All MIBs › BRIDGE-OPT-MIB
Category: Network Interfaces, VLAN and Bridging
Description: Manages bridge protocol options and spanning tree configuration for LAN bridge devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is BRIDGE-OPT-MIB?
BRIDGE-OPT-MIB is understood, from its name, to be a MIB extending standard bridge (IEEE 802.1D) management with optional spanning-tree and bridge-protocol configuration objects for Ethernet LAN bridges and switches. It would expose spanning-tree configuration and per-bridge-port state extensions beyond the base BRIDGE-MIB (RFC 4188). It would primarily support monitoring the software/protocol status of a device's bridging function -- spanning-tree topology state and per-port role/state such as blocking, listening, learning, or forwarding -- used to detect loops or topology changes rather than physical hardware sensor readings. It very likely builds on and depends on the standard BRIDGE-MIB, which it supplements with optional or extended objects. No module description or sample object names were retrievable for this MIB to confirm these details, so this characterization is based on its module name and conventional bridge-MIB structure. It's typically deployed on Ethernet bridges and Layer 2 switches implementing spanning tree, across various vendors, and network engineers can get the BRIDGE-OPT-MIB download to load into their MIB browser for spanning-tree monitoring.
IPNetwork Monitor allows you to monitor SNMP objects defined in BRIDGE-OPT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Motorola Codex 6500-series data/statistical multiplexer (legacy)
Monitoring Examples
No sample object or table names were retrievable for this MIB, so a concrete polling example can't be grounded in real identifiers. In general, a bridge "options" extension MIB of this kind would be polled for per-port spanning-tree state/role, which an operator would use to detect a topology change or a port unexpectedly transitioning into a blocking state, indicating a loop or link failure.
What Can Be Monitored
- spanning tree port state (blocking/listening/learning/forwarding)
- spanning tree topology change status
- bridge protocol configuration parameters
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| enterprises |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| cdx6500 | 1.3.6.1.4.1.449.2.1 | |||
| cdx6500CfgProtocolGroup | 1.3.6.1.4.1.449.2.1.2.1 | |||
| cdx6500Configuration | 1.3.6.1.4.1.449.2.1.2 | |||
| cdx6500dot1dBaseLinkStats | 1.3.6.1.4.1.449.2.1.3.1.5.10.3 | |||
| cdx6500dot1dBasePortCfg | 1.3.6.1.4.1.449.2.1.2.1.6.7.1 | |||
| cdx6500dot1dBasePortStats | 1.3.6.1.4.1.449.2.1.3.1.5.10.1 | |||
| cdx6500dot1dBridgeCfgGroup | 1.3.6.1.4.1.449.2.1.2.1.6.7 | |||
| cdx6500dot1dBridgeStatsGroup | 1.3.6.1.4.1.449.2.1.3.1.5.10 | |||
| cdx6500dot1dStpPortCfg | 1.3.6.1.4.1.449.2.1.2.1.6.7.2 | |||
| cdx6500dot1dTpPortStats | 1.3.6.1.4.1.449.2.1.3.1.5.10.2 | |||
| INT cdx6500LfcmBaseLink | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.1 | INTEGER | read-only | This object is the WAN Bridge Link number for control and statistics. |
| INT cdx6500LfcmBaseLinkBlStatus | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.4 | INTEGER | read-only | The status of the WAN Brdige Link: configErr = Configuration error on link swDisabled = Physical errors on link userDisabled = User shut down link congested = WAN congested condition inactive = Configured link - ready for use but not active active = Configured and active link unconfig = Not configured. newvalConfigErr = same functionality as 'configErr', new enumeration added for RFC1155 compatibility. |
| OID cdx6500LfcmBaseLinkCircuit | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.3 | OBJECT IDENTIFIER | read-only | For a WAN Bridge Link which (potentially) has the same value of dot1dBasePortIfIndex as another WAN Bridge Link on the same bridge, this object contains the name of an object instance unique to this WAN Bridge Link. For example, in the case where multiple ports correspond one-to-one with multiple X.25 virtual circuits, this value might identify an (e.g., the first) object instance associated with the X.25 virtual circuit corresponding to this port. For a WAN Bridge Link which has a unique value of dot1dBasePortIfIndex, this object can have the value { 0 0 }. Not Supported, will return zero |
| INT cdx6500LfcmBaseLinkClearStats | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.5 | INTEGER | write-only | This is the command to reset the LAN port bridge statistics. |
| INT cdx6500LfcmBaseLinkIfIndex | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.2 | INTEGER | read-only | The value of the instance of the ifIndex object, for the interface corresponding to this WAN Bridge Link. Not Supported, will return zero |
| INT cdx6500LfcmBaseLinkIndex | 1.3.6.1.4.1.449.2.1.2.1.6.9.1.1 | INTEGER | read-only | This is the WAN Bridge Link number (5 - 36) that identifies the particular Bridge Link. |
| STR cdx6500LfcmBaseLinkLastStatReset | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.6 | DisplayString | read-only | The time of the last LAN port statistics reset. |
| INT cdx6500LfcmBaseLlcLtrmDataPri | 1.3.6.1.4.1.449.2.1.2.1.6.7.3.7 | INTEGER | read-write | This parameter specifies the transmission priority of the LLC LT data over WAN. |
| INT cdx6500LfcmBasePort | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.1 | INTEGER | read-only | The port number of the port for which this entry contains bridge management information. |
| INT cdx6500LfcmBasePortIndex | 1.3.6.1.4.1.449.2.1.2.1.6.10.1.1 | INTEGER | read-only | The port number of the port for which this entry contains bridge management information. |
| INT cdx6500LfcmBridgeBoot | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.5 | INTEGER | write-only | This is the command to boot the LAN port bridge parameters. |
| STR cdx6500LfcmBridgedProtocols | 1.3.6.1.4.1.449.2.1.2.1.6.7.1.5 | DisplayString | read-write | NONE - No routable protocols can be bridged IP - IP packets can be bridged IPX - IPX packets can be bridged APPLETALK - AppleTalk and AARP packets can be bridged. |
| INT cdx6500LfcmBridgeId | 1.3.6.1.4.1.449.2.1.2.1.6.7.1.7 | INTEGER | read-write | This is the bridge ID used for bridging between local token ring ports. A value of 0 disables bridging between the local token ring ports. |
| INT cdx6500LfcmBridgeLfMode | 1.3.6.1.4.1.449.2.1.2.1.6.7.1.1 | INTEGER | read-write | The maximum size of the INFO field that this Bridge Link can send and receive. The minimum value of this parameter or of adjacent Bridge Link or values of Largest Frame Size of bridge wide parameter is used to determine whether a modification of the Routing Control field of RIF is necessary. Deprecated object without replacement |
| INT cdx6500LfcmBridgeLinkStatus | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.2 | INTEGER | read-only | The status of the LAN Port link: unconfig = Not configured configerr = Configuration error on link swDisabled = Physical errors on link userDisabled = User shut down link congested = WAN congested condition inactive = Configured link - ready for use but not active active = Configured and active link. newvalConfigErr = same functionality as 'configErr', new enumeration added for RFC1155 compatibility. |
| INT cdx6500LfcmClearStats | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.3 | INTEGER | write-only | This is the command to reset the LAN port bridge statistics. |
| INT cdx6500LfcmCtrlsLinkClrLinkProt | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.11 | INTEGER | write-only | This is a command to clear Unicast Protection for the WAN Bridge Link. |
| INT cdx6500LfcmCtrlsLinkClrMultProt | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.13 | INTEGER | write-only | This is a command to clear Multicast Protection for the WAN Bridge Link. |
| INT cdx6500LfcmCtrlsLinkSetLinkProt | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.10 | INTEGER | write-only | This is a command to set Unicast Protection for the WAN Bridge Link. |
| INT cdx6500LfcmCtrlsLinkSetMultProt | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.12 | INTEGER | write-only | This is a command to set Multicast Protection for the WAN Bridge Link. |
| INT cdx6500LfcmCtrlsPortClrLinkProt | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.10 | INTEGER | write-only | This is a command to clear Unicast Protection for the LAN Bridge Link. |
| INT cdx6500LfcmCtrlsPortClrMultProt | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.12 | INTEGER | write-only | This is a command to clear Multicast Protection for the LAN Bridge Link. |
| INT cdx6500LfcmCtrlsPortSetLinkProt | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.9 | INTEGER | write-only | This is a command to set Unicast Protection for the LAN Bridge Link. |
| INT cdx6500LfcmCtrlsPortSetMultProt | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.11 | INTEGER | write-only | This is a command to set Multicast Protection for the LAN Bridge Link. |
| STR cdx6500LfcmLastStatsReset | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.4 | DisplayString | read-only | The time of the last LAN port statistics reset. |
| INT cdx6500LfcmLearnOnlyPeriod | 1.3.6.1.4.1.449.2.1.2.1.6.7.1.3 | INTEGER | read-write | This is the time in seconds that a bridge will be prevented from forwarding frames after the Forwarding is cleared due to node boot. |
| INT cdx6500LfcmLinkBlDisable | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.9 | INTEGER | write-only | This is the command to Disable the WAN Bridge Link. |
| INT cdx6500LfcmLinkBlEnable | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.8 | INTEGER | write-only | This is the command to Enable the WAN Bridge Link. |
| INT cdx6500LfcmLinkBridgeLinkBoot | 1.3.6.1.4.1.449.2.1.3.1.5.4.1.7 | INTEGER | write-only | This is the command to boot the WAN Bridge Link parameters. |
| CTR cdx6500LfcmLinkFilDestAddrInDisc | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.4 | Counter | read-only | The number of inbound frames on this bridge link that were not forwarded because of Destination MAC Address filtering. |
| CTR cdx6500LfcmLinkFilDestAddrOutDisc | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.5 | Counter | read-only | The number of outbound frames on this bridge link that were not forwarded because of Destination MAC Address filtering. |
| CTR cdx6500LfcmLinkFilProtInDisc | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.6 | Counter | read-only | The number of inbound frames on this bridge link that were not forwarded because of Protocol filtering. |
| CTR cdx6500LfcmLinkFilProtOutDisc | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.7 | Counter | read-only | The number of outbound frames on this bridge link that were not forwarded because of Protocol filtering. |
| CTR cdx6500LfcmLinkFilSrcAddrInDisc | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.2 | Counter | read-only | The number of inbound frames on this bridge link that were not forwarded becauseof Source MAC Address filtering. |
| CTR cdx6500LfcmLinkFilSrcAddrOutDisc | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.3 | Counter | read-only | The number of outbound frames on this bridge link that were not forwarded becauseof Source MAC Address filtering. |
| INT cdx6500LfcmLinkFilterIndex | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.1 | INTEGER | read-only | The bridge link for which this entry contains filter information. |
| CTR cdx6500LfcmLinkFilTotalInDisc | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.8 | Counter | read-only | The sum of Source MAC Address, Destination MAC Address, and Protocol inbound frames on this bridge link not forwarded because of filtering. |
| CTR cdx6500LfcmLinkFilTotalOutDisc | 1.3.6.1.4.1.449.2.1.3.1.5.8.1.9 | Counter | read-only | The sum of Source MAC Address, Destination MAC Address, and Protocol outbound frames on this bridge link not forwarded because of filtering. |
| MAC cdx6500LfcmLinkStaticAddress | 1.3.6.1.4.1.449.2.1.2.1.6.4.1.1 | MacAddress | read-only | The destination MAC address in a frame to which this entry's filtering information applies. This object can take the value of a unicast address, a group address or the broadcast address. |
| OCT cdx6500LfcmLinkStaticAllowToGoTo | 1.3.6.1.4.1.449.2.1.2.1.6.4.1.3 | OCTET STRING | read-only | The set of WAN Bridge Links to which frames received from a specific port and destined for a specific MAC address, are allowed to be forwarded. Each octet within the value of this object specifies a set of eight bridge links, with the first octet specifying links 1 through 8, the second octet specifying links 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered link, and the least significant bit represents the highest numbered link. Thus, each link of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that link is included in the set of links; the link is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the link from which a frame is received is irrelevant.) |
| INT cdx6500LfcmLinkStaticReceivePort | 1.3.6.1.4.1.449.2.1.2.1.6.4.1.2 | INTEGER | read-only | Either the value '0', or the WAN Bridge Link of the link from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all bridge links of the bridge for which there is no other applicable entry. |
| INT cdx6500LfcmLinkStaticStatus | 1.3.6.1.4.1.449.2.1.2.1.6.4.1.4 | INTEGER | read-only | This object indicates the status of this entry. other - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid - writing this value to the object removes the corresponding entry. permanent - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout - this entry is currently in use and will remain so until it is aged out. |
| STR cdx6500LfcmLinkType | 1.3.6.1.4.1.449.2.1.2.1.6.9.1.2 | DisplayString | read-write | This is the bridge type for links which connect to WANs and defines the kind of bridging that will be employed on the link: applies only to WAN Bridge, Links number 5 to 36. |
| INT cdx6500LfcmLssBridgeId | 1.3.6.1.4.1.449.2.1.2.1.6.7.4.2 | INTEGER | read-write | This is the bridge ID of a virtual bridge and it uniquely identifies a bridge when more than one bridge is used to span the same two segments. |
| INT cdx6500LfcmLssCalculationInter | 1.3.6.1.4.1.449.2.1.2.1.6.7.4.4 | INTEGER | read-only | The Calculation Interval Time. Deprecated object without replacement. |
| INT cdx6500LfcmLssNotificationInter | 1.3.6.1.4.1.449.2.1.2.1.6.7.4.3 | INTEGER | read-only | The Notification Interval Time Deprecated object without replacement. |
| INT cdx6500LfcmLssPathTraceCtrl | 1.3.6.1.4.1.449.2.1.2.1.6.7.4.5 | INTEGER | read-write | The value of this parameter specifies whether or not the LBS is enabled to send the Path Trace frames to the LAN Manager. newvalDisable : same functionality as 'disable', new enumeration added for RFC1155 compatibility. |
| STR cdx6500LfcmLssRingNumber | 1.3.6.1.4.1.449.2.1.2.1.6.7.1.4 | DisplayString | read-write | This is a virtual ring number that is used by the 6500 whenever a virtual ring definition is required: to support the LSS in its path trace function and in IP tunnelling for token ring networks. Range : 1 - 0xFFF. |
| MAC cdx6500LfcmLssVirtualPortMacAddr | 1.3.6.1.4.1.449.2.1.2.1.6.7.4.1 | MacAddress | read-write | Specifies the MAC address of the virtual LAN port of the virtual ring. The entered value will be replaced by the Burned In Address (BIA) if the LAN hardware is present. |
| MAC cdx6500LfcmLtrmMacAddress | 1.3.6.1.4.1.449.2.1.2.1.6.5.1.2 | MacAddress | read-write | This MAC address must match the Source MAC address of the frame received from the LAN port or destination MAC address of a frame received from WAN for the session to be spoofed. |
| INT cdx6500LfcmLtrmProfEntryNumber | 1.3.6.1.4.1.449.2.1.2.1.6.6.1.1 | INTEGER | read-write | The Profile Number (1 - 8) that is to be configured. |
| STR cdx6500LfcmLtrmProfileName | 1.3.6.1.4.1.449.2.1.2.1.6.5.1.4 | DisplayString | read-write | Local Term Station Table reference this parameter for the T1, T2, Ti, N2, N3 and TW values. |
| STR cdx6500LfcmLtrmProfLlcName | 1.3.6.1.4.1.449.2.1.2.1.6.6.1.2 | DisplayString | read-write | Local Term Station Table reference this parameter for the T1, T2, Ti, N2, N3 and TW values. |
| INT cdx6500LfcmLtrmProfN2 | 1.3.6.1.4.1.449.2.1.2.1.6.6.1.6 | INTEGER | read-write | This count defines the number of times an I frame or supervisory frame with poll bit set to 1, will be transmitted, due to T1 acknowledgment time-out, before the Logical Link will be declared down (inoperative). |
| INT cdx6500LfcmLtrmProfN3 | 1.3.6.1.4.1.449.2.1.2.1.6.6.1.7 | INTEGER | read-write | The receive count is used in conjunction with T2 to reduce the amount of acknowledgments a station generates. The receive count is used by a station to determine how many frames it will receive from the remote station while withholding acknowledgment of these frames. This is a method of reducing the amount of acknowledgments generated by a link station. When this count expires, the link station should immediately send an acknowledgment for all received frames not yet acknowledged. |
| INT cdx6500LfcmLtrmProfTimeout1 | 1.3.6.1.4.1.449.2.1.2.1.6.6.1.3 | INTEGER | read-write | This Ack Timer is used by a station to detect a failure of the remote station to acknowledge an outstanding I frame or supervisory frame with poll bit set to 1. Time is in seconds. |
| INT cdx6500LfcmLtrmProfTimeout2 | 1.3.6.1.4.1.449.2.1.2.1.6.6.1.4 | INTEGER | read-write | The Receive Ack Timer is used by a station to determine how long it will withhold acknowledgment of a frame(s) from the remote station that require acknowledgment. This is a method of reducing the amount of acknowledgments generated by a link station. When this timer expires, the link station should immediately send an acknowledgment for all received frames not yet acknowledged. Time is in tenths of seconds. |
| INT cdx6500LfcmLtrmProfTimeout3 | 1.3.6.1.4.1.449.2.1.2.1.6.6.1.5 | INTEGER | read-write | The Idle Timer is used by a station to detect an inoperative condition of the Logical Link. This timer is started when the link becomes idle (no data to pass and no outstanding acknowledgments) and if it expires, the station sends a supervisory frame with the poll bit set to 1. Time is in seconds. |
| INT cdx6500LfcmLtrmProfTxWindowsize | 1.3.6.1.4.1.449.2.1.2.1.6.6.1.8 | INTEGER | read-write | Transmit Window Size is the maximum number of I frames a station may transmit without acknowledgment. |
| INT cdx6500LfcmLtrmSap | 1.3.6.1.4.1.449.2.1.2.1.6.5.1.3 | INTEGER | read-write | This SAP must match the Source SAP of the frame received from the LAN port or destination SAP of a frame received from WAN for the session to be spoofed. |
| INT cdx6500LfcmLtrmStatsBoot | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.18 | INTEGER | read-only | This command is used to boot a Local Termination session when set to `boot'. |
| CTR cdx6500LfcmLtrmStatsCtFrRejIn | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.12 | Counter | read-only | The number of Reject frames received. |
| CTR cdx6500LfcmLtrmStatsCtFrRejOut | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.13 | Counter | read-only | The number of Reject frames transmitted. |
| CTR cdx6500LfcmLtrmStatsCtFrRnrIn | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.8 | Counter | read-only | The number of Receiver Not Ready frames received. |
| CTR cdx6500LfcmLtrmStatsCtFrRnrOut | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.9 | Counter | read-only | The number of Receiver Not Ready frames transmitted. |
| CTR cdx6500LfcmLtrmStatsCtFrRrIn | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.6 | Counter | read-only | The number of Receiver Ready frames received. |
| CTR cdx6500LfcmLtrmStatsCtFrRrOut | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.7 | Counter | read-only | The number of Receiver Ready frames transmitted. |
| CTR cdx6500LfcmLtrmStatsCtFrSabmeIn | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.14 | Counter | read-only | The number of SABME frames received. |
| CTR cdx6500LfcmLtrmStatsCtFrSabmeOut | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.15 | Counter | read-only | The number of SABME frames transmitted. |
| CTR cdx6500LfcmLtrmStatsCtFrXidIn | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.10 | Counter | read-only | The number of ID Exchange frames received. |
| CTR cdx6500LfcmLtrmStatsCtFrXidOut | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.11 | Counter | read-only | The number of ID Exchange frames transmitted. |
| CTR cdx6500LfcmLtrmStatsDataCharIn | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.2 | Counter | read-only | The number of data bytes received. |
| CTR cdx6500LfcmLtrmStatsDataCharOut | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.3 | Counter | read-only | The number of data bytes transmitted. |
| CTR cdx6500LfcmLtrmStatsDataFrIn | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.4 | Counter | read-only | The number of data frames received. |
| CTR cdx6500LfcmLtrmStatsDataFrOut | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.5 | Counter | read-only | The number of data frames transmitted. |
| INT cdx6500LfcmLtrmStatsIndex | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.1 | INTEGER | read-only | This is the Session number for which there is statistics. |
| CTR cdx6500LfcmLtrmStatsTotFrInData | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.16 | Counter | read-only | The sum of Data Frames, Receiver Ready, Receiver Not Ready, Reject, SABME and ID Exchange frames received. |
| CTR cdx6500LfcmLtrmStatsTotFrOutData | 1.3.6.1.4.1.449.2.1.3.1.5.9.1.17 | Counter | read-only | The sum of Data Frames, Receiver Ready, Receiver Not Ready, Reject, SABME and ID Exchange frames transmitted. |
| INT cdx6500LfcmLtrmStnEntryNumber | 1.3.6.1.4.1.449.2.1.2.1.6.5.1.1 | INTEGER | read-only | The Station Number (1 - 64) that is to be configured. |
| INT cdx6500LfcmLtrmWanN2 | 1.3.6.1.4.1.449.2.1.2.1.6.7.3.4 | INTEGER | read-write | This count defines the number of times an I frame or supervisory frame with poll bit set to 1, will be transmitted, due to T1 acknowledgment time-out, before the Logical Link will be declared down (inoperative). |
| INT cdx6500LfcmLtrmWanN3 | 1.3.6.1.4.1.449.2.1.2.1.6.7.3.5 | INTEGER | read-write | The receive count is used in conjunction with T2 to reduce the amount of acknowledgments a station generates. The receive count is used by a station to determine how many frames it will receive from the remote station while withholding acknowledgment of these frames. This is a method of reducing the amount of acknowledgments generated by a link station. When this count expires, the link station should immediately send an acknowledgment for all received frames not yet acknowledged. |
| INT cdx6500LfcmLtrmWanTimeout1 | 1.3.6.1.4.1.449.2.1.2.1.6.7.3.1 | INTEGER | read-write | This Ack Timer is used by a station to detect a failure of the remote station to acknowledge an outstanding I frame or supervisory frame with poll bit set to 1. Time is in seconds. |
| INT cdx6500LfcmLtrmWanTimeout2 | 1.3.6.1.4.1.449.2.1.2.1.6.7.3.2 | INTEGER | read-write | The Receive Ack Timer is used by a station to determine how long it will withhold acknowledgment of a frame(s) from the remote station that require acknowledgment. This is a method of reducing the amount of acknowledgments generated by a link station. When this timer expires, the link station should immediately send an acknowledgment for all received frames not yet acknowledged. Time is in tenths of seconds. |
| INT cdx6500LfcmLtrmWanTimeout3 | 1.3.6.1.4.1.449.2.1.2.1.6.7.3.3 | INTEGER | read-write | The Idle Timer is used by a station to detect an inoperative condition of the Logical Link. This timer is started when the link becomes idle (no data to pass and no outstanding acknowledgments) and if it expires, the station sends a supervisory frame with the poll bit set to 1. Time is in seconds. |
| INT cdx6500LfcmLtrmWanTxWindowSize | 1.3.6.1.4.1.449.2.1.2.1.6.7.3.6 | INTEGER | read-write | Transmit Window Size is the maximum number of I frames a station may transmit without acknowledgment. |
| INT cdx6500LfcmMacAddrFilterAction | 1.3.6.1.4.1.449.2.1.2.1.6.9.1.3 | INTEGER | read-write | pass = Pass all frames with MAC address not listed in MAC Address Filter Table block = Block all frames with MAC address not listed in MAC Address Filter Table none = No MAC address filtering to be performed for this link. newvalPass = same action as 'pass', new enumeration added for RFc1155 compatibility. |
| INT cdx6500LfcmMaxBridgeLinks | 1.3.6.1.4.1.449.2.1.2.1.6.7.1.6 | INTEGER | read-write | This parameter specifies the maximum number of bridge links that can be configured. |
| STR cdx6500LfcmNbiosAsciiName | 1.3.6.1.4.1.449.2.1.2.1.6.11.1.3 | DisplayString | read-write | The NETBIOS name indicates the name that will be filtered or forwarded. A name consisting of up to 16 characters may be entered. The name is case sensitive. The wildcard character '?' matches any character. The wildcard character '*' at the end of the name matches all remaining characters. |
| INT cdx6500LfcmNbiosFilterAction | 1.3.6.1.4.1.449.2.1.2.1.6.9.1.6 | INTEGER | read-write | pass = Pass all frames with MAC address not listed in MAC Address Filter Table block = Block all frames with MAC address not listed in MAC Address Filter Table none = No MAC address filtering to be performed for this link. newvalPass = same action as 'pass', new enumeration added for RFc1155 compatibility. |
| STR cdx6500LfcmNbiosHexName | 1.3.6.1.4.1.449.2.1.2.1.6.11.1.4 | DisplayString | read-write | The NETBIOS name indicates the name that will be filtered or forwarded. A name consisting of 16 bytes may be entered in hexdecimal format ex:32 hexdecimal characters, without any spaces between the characters. |
| STR cdx6500LfcmNbiosIncAction | 1.3.6.1.4.1.449.2.1.2.1.6.11.1.5 | DisplayString | read-write | PASS = Pass all. BLOCK = Block all. PASSLIST = Pass List. BLOCKLIST = Block List. |
| STR cdx6500LfcmNbiosIncList | 1.3.6.1.4.1.449.2.1.2.1.6.11.1.6 | DisplayString | read-write | A range of link numbers can be entered. for example: 1,6,8-12 indicates 1,6,8,9,10,11,12. |
| STR cdx6500LfcmNbiosOutAction | 1.3.6.1.4.1.449.2.1.2.1.6.11.1.7 | DisplayString | read-write | PASS = Pass all. BLOCK = Block all. PASSLIST = Pass List. BLOCKLIST = Block List. |
| STR cdx6500LfcmNbiosOutList | 1.3.6.1.4.1.449.2.1.2.1.6.11.1.8 | DisplayString | read-write | A range of link numbers can be entered. for example: 1,6,8-12 indicates 1,6,8,9,10,11,12. |
| INT cdx6500LfcmNbiosStrType | 1.3.6.1.4.1.449.2.1.2.1.6.11.1.2 | INTEGER | read-write | The NETBIOS name can be entered in ASCII or HEX format. 'ASCII' means ACSII characters may be entered for the name. 'HEX' means hexadecimal values may be entered. |
| INT cdx6500LfcmNetBiosIndex | 1.3.6.1.4.1.449.2.1.2.1.6.11.1.1 | INTEGER | read-only | The Index number for which this entry contains bridge management information. |
| INT cdx6500LfcmNumLinks | 1.3.6.1.4.1.449.2.1.3.1.5.10.3.1 | INTEGER | read-only | The number of WAN Bridge Links that have been configured. |
| INT cdx6500LfcmPortAddrFiltAction | 1.3.6.1.4.1.449.2.1.2.1.6.10.1.2 | INTEGER | read-write | pass = Pass all frames with MAC address not listed in MAC Address Filter Table block = Block all frames with MAC address not listed in MAC Address Filter Table none = No MAC address filtering to be performed for this link. newvalPass = same functionality as 'pass', new enumeration added for RFC1155 compatibility. |
| INT cdx6500LfcmPortBlDisable | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.8 | INTEGER | write-only | This is the command to Disable the LAN port Bridge Link. |
| INT cdx6500LfcmPortBlEnable | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.7 | INTEGER | write-only | This is the command to Enable the LAN port Bridge Link. |
| INT cdx6500LfcmPortBridgeLinkBoot | 1.3.6.1.4.1.449.2.1.3.1.5.11.1.6 | INTEGER | write-only | This is the command to boot the LAN port Bridge Link parameters. |
| CTR cdx6500LfcmPortFilDestAddrInDisc | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.4 | Counter | read-only | The number of inbound frames on this port that were not forwarded because of Destination MAC Address filtering. |
| CTR cdx6500LfcmPortFilDestAddrOutDisc | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.5 | Counter | read-only | The number of outbound frames on this port that were not forwarded because of Destination MAC Address filtering. |
| CTR cdx6500LfcmPortFilProtInDisc | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.6 | Counter | read-only | The number of inbound frames on this port that were not forwarded because of Protocol filtering. |
| CTR cdx6500LfcmPortFilProtOutDisc | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.7 | Counter | read-only | The number of outbound frames on this port that were not forwarded because of Protocol filtering. |
| CTR cdx6500LfcmPortFilSrcAddrInDisc | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.2 | Counter | read-only | The number of inbound frames on this port that were not forwarded because of Source MAC Address filtering. |
| CTR cdx6500LfcmPortFilSrcAddrOutDisc | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.3 | Counter | read-only | The number of outbound frames on this port that were not forwarded because of Source MAC Address filtering. |
| INT cdx6500LfcmPortFilterIfIndex | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.1 | INTEGER | read-only | The port number of the port for which this entry contains filter information. |
| CTR cdx6500LfcmPortFilTotalInDisc | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.8 | Counter | read-only | The sum of Source MAC Address, Destination MAC Address, and Protocol inbound frames on this port not forwarded because of filtering. |
| CTR cdx6500LfcmPortFilTotalOutDisc | 1.3.6.1.4.1.449.2.1.3.1.5.3.1.9 | Counter | read-only | The sum of Source MAC Address, Destination MAC Address, and Protocol outbound frames on this port not forwarded because of filtering. |
| INT cdx6500LfcmPortProtFiltAction | 1.3.6.1.4.1.449.2.1.2.1.6.10.1.3 | INTEGER | read-write | pass = Pass all frames with Protocol value not listed in Protocol Filter Table block = Block all frames with Protocol value not listed in Protocol Filter Table none = No Protocol filtering to be performed for this link. newvalPass = same functionality as 'pass', new enumeration added for RFC1155 compatibility. |
| INT cdx6500LfcmPortStptManState | 1.3.6.1.4.1.449.2.1.2.1.6.10.1.4 | INTEGER | read-write | Value of this parameters specifies whether to forward or block a STE (or Single Route Broadcast ) frame while the STPE Control parameter is configured to MAN. newvalForward : same functionality as 'newvalForward', new enumeration added for RFC1155 compatibility. |
| INT cdx6500LfcmProtocolFilterAction | 1.3.6.1.4.1.449.2.1.2.1.6.9.1.4 | INTEGER | read-write | pass = Pass all frames with Protocol value not listed in Protocol Filter Table block = Block all frames with Protocol value not listed in Protocol Filter Table none = No Protocol filtering to be performed for this link. newvalPass = same action as 'pass', new enumeration added for RFc1155 compatibility. |
| INT cdx6500LfcmSrLink | 1.3.6.1.4.1.449.2.1.2.1.6.3.1.1 | INTEGER | read-only | The link number of the WAN Bridge Linkfor which this entry contains Source Route management information. |
| CTR cdx6500LfcmSrLinkApeInFrames | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.5 | Counter | read-only | The number of all paths explorer frames that have been received by this bridge link from its segment. |
| CTR cdx6500LfcmSrLinkApeOutFrames | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.6 | Counter | read-only | The number of all paths explorer frames that have been transmitted by this bridge link on its segment. |
| INT cdx6500LfcmSrLinkBridgeNum | 1.3.6.1.4.1.449.2.1.2.1.6.3.1.3 | INTEGER | read-write | A bridge number uniquely identifies a bridge when more than one bridge is used to span the same two segments. Current source routing protocols limit this value to the range: 0 through 15. A value of 65535 signifies that no bridge number is assigned to this bridge. |
| CTR cdx6500LfcmSrLinkDupSegDisc | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.10 | Counter | read-only | The number of frames that have been discarded by this bridge link because the routing descriptor field contained a duplicate segment identifier. |
| INT cdx6500LfcmSrLinkHopCount | 1.3.6.1.4.1.449.2.1.2.1.6.3.1.2 | INTEGER | read-write | The maximum number of routing descriptors allowed in an All Paths or Spanning Tree Explorer frames. |
| CTR cdx6500LfcmSrLinkHopCountExcDisc | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.11 | Counter | read-only | The number of explorer frames that have been discarded by this bridge link because the Routing Information Field has exceeded the maximum route descriptor length. |
| INT cdx6500LfcmSrLinkIfIndex | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.1 | INTEGER | read-only | The bridge link number of the WAN Bridge Link for which this entry contains Source Route management information. |
| INT cdx6500LfcmSrLinkLargestFrame | 1.3.6.1.4.1.449.2.1.2.1.6.3.1.5 | INTEGER | read-write | The maximum size of the INFO field (LLC and above) that this port can send/receive. It does not include any MAC level (framing) octets. The value of this object is used by this bridge to determine whether a modification of the LargestFrame field of the Routing Control field of the Routing Information Field is necessary. Valid values as defined by the 802.5 source routing bridging specification are 516, 1500, 2052, 4472, 8144, 11407, 17800, and 65535 octets. Behavior of the WAN Bridge LINK when an illegal value is written is implementation specific. It is recommended that a reasonable legal value be chosen. |
| INT cdx6500LfcmSrLinkMode | 1.3.6.1.4.1.449.2.1.2.1.6.3.1.6 | INTEGER | read-write | NORMAL - Bridge link connects to another Bridge using the Link Control Protocol to determine remote Ring Number RFC1294- Bridge link uses RFC1294 (or RFC1490) bridging to connect to another Bridge or FRAD. TRANS- Bridge link does translational bridging of frames received from a Transparent Bridge. |
| INT cdx6500LfcmSrLinkNextRingNumber | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.14 | INTEGER | read-only | The Next Ring number of the WAN bridge link to which the bridge route is bridging. This is the ring number to which the Codex remote bridge halfis attached. |
| CTR cdx6500LfcmSrLinkSegMisDisc | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.9 | Counter | read-only | The number of explorer frames that have been discarded by this bridge link because the routing descriptor field contained an invalid adjacent segment value. |
| CTR cdx6500LfcmSrLinkSpecInFrames | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.3 | Counter | read-only | The number of specifically routed frames that have been received from this bridge link's segment. |
| CTR cdx6500LfcmSrLinkSpecOutFrames | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.4 | Counter | read-only | The number of specifically routed frames that this bridge link has transmitted on its segment. |
| CTR cdx6500LfcmSrLinkSteinFrames | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.8 | Counter | read-only | The number of spanning tree explorer frames that have been received by this bridge Link from its segment. |
| CTR cdx6500LfcmSrLinkSteOutFrames | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.7 | Counter | read-only | The number of spanning tree explorer frames that have been transmitted by this bridge link on its segment. |
| INT cdx6500LfcmSrLinkSteSpanMode | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.2 | INTEGER | read-only | This object is no longer supported. |
| INT cdx6500LfcmSrLinkTargetSegment | 1.3.6.1.4.1.449.2.1.2.1.6.3.1.4 | INTEGER | read-only | The segment number that corresponds to the target segment this port is considered to be connected to by the bridge. Current source routing protocols limit this value to the range: 0 through 4095. A value of 65535 signifies that no target segment is assigned to this port. |
| CTR cdx6500LfcmSrLinkTotalFramesRx | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.12 | Counter | read-only | The sum of ARE, STE and SRF frames received on this bridge link. |
| CTR cdx6500LfcmSrLinkTotalFramesTx | 1.3.6.1.4.1.449.2.1.3.1.5.5.1.13 | Counter | read-only | The sum of ARE, STE and SRF frames transmitted on this bridge link. |
| STR cdx6500LfcmSrLinkVsegNum | 1.3.6.1.4.1.449.2.1.2.1.6.3.1.7 | DisplayString | read-write | This is a virtual ring number that is used by the Bridge Link for connecting to another Bridge or FRAD via RFC1294 or RFC1490 Bridging. Range : 1 - 0xFFF. |
| CTR cdx6500LfcmSrPortFramesRx | 1.3.6.1.4.1.449.2.1.3.1.5.1.1.2 | Counter | read-only | The sum of ARE, STE and SRF frames received on this LAN link. |
| CTR cdx6500LfcmSrPortFramesTx | 1.3.6.1.4.1.449.2.1.3.1.5.1.1.3 | Counter | read-only | The sum of ARE, STE and SRF frames transmitted on this LAN link. |
| INT cdx6500LfcmSrPortIfIndex | 1.3.6.1.4.1.449.2.1.3.1.5.1.1.1 | INTEGER | read-only | The port number of the port for which this entry contains Source Route management information. |
| INT cdx6500LfcmSrPortRingNumber | 1.3.6.1.4.1.449.2.1.3.1.5.1.1.4 | INTEGER | read-only | The Next Ring number of the LAN link to which the bridge route is bridging. This is the ring number to which the Codex remote bridge half is attached. Deprecated object without replacement |
| INT cdx6500LfcmStaticAddrEntryNumber | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.1 | INTEGER | read-only | The number of the table entry corresponding to the MAC address that is subject to Filtering Action. The Entry Number ranger is 1 - 300 |
| STR cdx6500LfcmStaticIncDestLinkAct | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.5 | DisplayString | read-write | PASS = Pass incoming frames with this MAC Address value on all links. (See User's Manual). BLOCK = Block incoming frames with this MAC Address value on all links. (See User's Manual). PASSLIST = Pass List. Links in this list will pass the frame. Links not in this list will block the frame. (See User's Manual). BLOCKLIST = Block List. Links in this list will block the frame. Links not in this list will pass the frame. (See User's Manual). |
| STR cdx6500LfcmStaticIncDestList | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.9 | DisplayString | read-write | The individual numbers correspond to the Links which will be filtered according to the preceding parameter: PASSLIST = the listed links will pass the frame and unlisted links will block the frame. BLOCKLIST = the listed links will block the frame and unlisted links pass the frame A range of link numbers can be entered, for example: 1,6,8-12 indicates 1,6,8,9,10,11,12 |
| STR cdx6500LfcmStaticIncProtLinkAct | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.4 | DisplayString | read-write | PASS = Pass all. If this value is used, incoming frames with the specified protocol value will be passed on all links. All other protocols will be blocked on incoming links. (See User's Manual). BLOCK = Block all. If this value is used, incoming frames with the specified protocol value will be blocked on all links. All other protocols will be passed on incoming links. (See User's Manual). PASSLIST = Pass List. Links in the list will pass the frame. Links not in this list will block the frame. An empty list means all links will block. (See User's Manual). BLOCKLIST = Block List. Links in the list will block the frame. Links not in this list will pass the frame. An empty list will mean all links will pass. (See User's Manual). |
| STR cdx6500LfcmStaticIncProtList | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.6 | DisplayString | read-write | The individual numbers correspond to the Links which will be filtered according to the preceding parameter: PASSLIST = the listed links will pass the frame and unlisted links will block the frame. An empty list means all links will block. BLOCKLIST = the listed links will block the frame and unlisted links will pass the frame. An empty list will mean all links will pass. A range of link numbers can be entered, for example: 1,6,8-12 indicates 1,6,8,9,10,11,12 |
| STR cdx6500LfcmStaticIncSrcLinkAct | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.3 | DisplayString | read-write | PASS = Pass incoming frames with this MAC Address value on all links. (See User's Manual). BLOCK = Block incoming frames with this MAC Address value on all links. (See User's Manual). PASSLIST = Pass List. Links in this list will pass the frame. Links not in this list will block the frame. (See User's Manual). BLOCKLIST = Block List. Links in this list will block the frame. Links not in this list will pass the frame. (See User's Manual). |
| STR cdx6500LfcmStaticIncSrcList | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.7 | DisplayString | read-write | The individual numbers correspond to the Links which will be filtered according to the preceding parameter: PASSLIST = the listed links will pass the frame and unlisted links will block the frame. BLOCKLIST = the listed links will block the frame and unlisted links will pass the frame. A range of link numbers can be entered, for example: 1,6,8-12 indicates 1,6,8,9,10,11,12 |
| MAC cdx6500LfcmStaticMacAddr | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.2 | MacAddress | read-write | MAC Address subject to Filtering action |
| MAC cdx6500LfcmStaticMacMask | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.11 | MacAddress | read-only | This object contains a six-byte mask to indicate which nibbles in cdx6500LfcmStaticMacAddr object contain a wild card. A mask nibble with value 'F' shows no wild card in corresponding nibble in MacAddress, while a mask nibble with value '0' shows a wild card. Any (0) nibbles in the mask corresponds to 'don't care' location in the Mac Address. Only the significant nibble positions are checked when comparing a frame's source or destination Mac Address to the cdx6500LfcmStaticMacAddr field. |
| STR cdx6500LfcmStaticOutDestLinkAct | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.6 | DisplayString | read-write | PASS = Pass outgoing frames with this MAC Address value on all links. (See User's Manual). BLOCK = Block outgoing frames with this MAC Address value on all links. (See User's Manual). PASSLIST = Pass List. Links in this list will pass the frame. Links not in this list will block the frame. (See User's Manual). BLOCKLIST = Block List. Links in this list will block the frame. Links not in this list will pass the frame. (See User's Manual). |
| STR cdx6500LfcmStaticOutDestList | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.10 | DisplayString | read-write | The individual numbers correspond to the Links which will be filtered according to the preceding parameter: PASSLIST = the listed links will pass the frame and unlisted links will block the frame. BLOCKLIST = the listed links will block the frame and unlisted links will pass the frame A range of link numbers can be entered, for example: 1,6,8-12 indicates 1,6,8,9,10,11,12 |
| STR cdx6500LfcmStaticOutProtLinkAct | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.5 | DisplayString | read-write | PASS = Pass all. If this value is used, outgoing frames with the specified protocol value will be passed on all links. All other protocols will be blocked on outgoing links. (See User's Manual). BLOCK = Block all. If this value is used, outgoing frames with the specified protocol value will be blocked on all links. All other protocols will be passed on outgoing links. (See User's Manual). PASSLIST = Pass List. Links in this list will pass the frame. Links not in this list will block the frame. An empty list means all links will block. (See User's Manual). BLOCKLIST = Block List. Links in this list will block the frame. Links not in this list will pass the frame. An empty list will mean all links will pass. (See User's Manual). |
| STR cdx6500LfcmStaticOutProtList | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.7 | DisplayString | read-write | The individual numbers correspond to the Links which will be filtered according to the preceding parameter: PASSLIST = the listed links will pass the frame and unlisted links will block the frame. An empty list means all links will block. BLOCKLIST = the listed links will block the frame and unlisted links will pass the frame. An empty list will mean all links will pass. A range of link numbers can be entered, for example: 1,6,8-12 indicates 1,6,8,9,10,11,12 |
| STR cdx6500LfcmStaticOutSrcLinkAct | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.4 | DisplayString | read-write | PASS = Pass outgoing frames with this MAC Address value on all links. (See User's Manual). BLOCK = Block outgoing frames with this MAC Address value on all links. (See User's Manual). PASSLIST = Pass List. Links in this list will pass the frame. Links not in this list will block the frame. (See User's Manual). BLOCKLIST = Block List. Links in this list will block the frame. Links not in this list will pass the frame. (See User's Manual). |
| STR cdx6500LfcmStaticOutSrcList | 1.3.6.1.4.1.449.2.1.2.1.6.1.1.8 | DisplayString | read-write | The individual numbers correspond to the Links which will be filtered according to the preceding parameter: PASSLIST = the listed links will pass the frame and unlisted links will block the frame BLOCKLIST = the listed links will block the frame and unlisted links will pass the frame A range of link numbers can be entered, for example: 1,6,8-12 indicates 1,6,8,9,10,11,12 |
| INT cdx6500LfcmStaticProtEntryNumber | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.1 | INTEGER | read-only | The number of the table entry corresponding to the Protocol Type that is subject to Filtering Action. The Entry Number ranger is 1 - 100 |
| INT cdx6500LfcmStaticType | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.2 | INTEGER | read-write | Protocol Type indicates what type of protocol is involved in the frame. dsap: The Protocol Value to be filtered/forwarded is the Destination SAP of the 802.2 LLC Protocol. snap: The Protocol Value to be filtered/forwarded is the SNAP header which identifies the OUI and Protocol type. eType: The Protocol Value to be filtered/forwarded is defined as the protocol ID of Ethernet type frame. newvalDsap : same functionality as 'dsap', new enumeration introduced for RFC1155 compatibility. |
| STR cdx6500LfcmStaticValue | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.3 | DisplayString | read-write | The protocol value indicates the value of the protocol that will be filtered or forwarded. for DSAP. Range : 0x00 - 0xFF. |
| STR cdx6500LfcmStaticValue1 | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.8 | DisplayString | read-write | The protocol value indicates the value of the protocol that will be filtered or forwarded. for SNAP(10 digit hex value) |
| STR cdx6500LfcmStaticValue2 | 1.3.6.1.4.1.449.2.1.2.1.6.2.1.9 | DisplayString | read-write | The protocol value indicates the value of the protocol that will be filtered or forwarded. for E-TYPE. Range : 0x5DD - 0xFFFF . |
| INT cdx6500LfcmStpBadHelloThreshold | 1.3.6.1.4.1.449.2.1.2.1.6.7.2.2 | INTEGER | read-write | A Bad Hello counter is incremented when HELLO PDU is received while the STPE Control parameter is configured to MAN. An event (report) is generated when the counter exceeds the value of this parameter. The event will be generated only once during the Bad Hello Time. |
| INT cdx6500LfcmStpBadHelloTimeout | 1.3.6.1.4.1.449.2.1.2.1.6.7.2.3 | INTEGER | read-write | This is a timeout value in minute. On timeout the Bad Hello counter is reset. |
| INT cdx6500LfcmStpControl | 1.3.6.1.4.1.449.2.1.2.1.6.7.2.1 | INTEGER | read-write | auto: This bridge participates in STP and automatically calculates the STE (Single Route Broadcast) frame path. man : The spanning tree is manually configured Configure Bridge Link parameter. newvalAuto : same functionality as 'auto', new enumeration added for RFC1155 compatibility. |
| BRI cdx6500LfcmStpDesignatedBridge | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.8 | BridgeId | read-only | The Bridge Identifier of the bridge which this bridge link considers to be the Designated Bridge for this bridge link's segment. |
| INT cdx6500LfcmStpDesignatedCost | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.7 | INTEGER | read-only | The path cost of the Designated Port of the segment connected to this bridge link. This value is compared to the Root Path Cost field in received bridge PDUs. |
| OCT cdx6500LfcmStpDesignatedPort | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.9 | OCTET STRING | read-only | The Port Identifier of the bridge link on the Designated Bridge for this bridge link's segment. |
| BRI cdx6500LfcmStpDesignatedRoot | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.6 | BridgeId | read-only | The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the bridge link is attached. |
| INT cdx6500LfcmStpEnable | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.4 | INTEGER | read-only | The enabled/disabled status of the bridge link. |
| CTR cdx6500LfcmStpForwardTransitions | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.10 | Counter | read-only | The number of times this port has transitioned from the Learning state to the Forwarding state. Not supported, will return zero. |
| INT cdx6500LfcmStpLink | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.1 | INTEGER | read-only | The bridge link number for which this entry contains Spanning Tree Protocol management information. |
| INT cdx6500LfcmStpLinkManState | 1.3.6.1.4.1.449.2.1.2.1.6.9.1.5 | INTEGER | read-write | Value of this parameters specifies whether to forward or block a STE (or Single Route Broadcast ) frame while the STPE Control parameter is configured to MAN. newvalForward : same functionality as 'forward', new enumeration added for RFC1155 compatibility. |
| INT cdx6500LfcmStpPathCost | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.5 | INTEGER | read-write | The contribution of this bridge link to the path cost of paths towards the spanning tree root which include this bridge link. |
| INT cdx6500LfcmStpPriority | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.2 | INTEGER | read-write | The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of cdx6500LfcmStpLink. |
| INT cdx6500LfcmStpState | 1.3.6.1.4.1.449.2.1.3.1.5.7.1.3 | INTEGER | read-only | The bridge link's current state as defined by application of the Spanning Tree Protocol. This state controls what action a bridge link takes on reception of a frame. For bridge links which are disabled (see cdx6500LfcmStpEnable), this object will have a value of 'disabled'. |
| INT cdx6500LfcmTbEntry | 1.3.6.1.4.1.449.2.1.2.1.6.8.1.1 | INTEGER | read-only | The number of the table entry corresponding to the MAC address used for Forwarding Action. The Entry Number ranger is 1 - 8000 |
| INT cdx6500LfcmTpLink | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.1 | INTEGER | read-only | The bridge link number of the port for which this entry contains Transparent bridging management information. |
| CTR cdx6500LfcmTpLinkBroadcastRx | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.10 | Counter | read-only | The number of Broadcast Frames received on this WAN Bridge Link. |
| CTR cdx6500LfcmTpLinkBroadcastTx | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.11 | Counter | read-only | The number of Broadcast Frames transmitted on this WAN Bridge Link. |
| CTR cdx6500LfcmTpLinkInBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.12 | Counter | read-only | The number of frames discarded due to receive link state not in forwarding state . |
| CTR cdx6500LfcmTpLinkInDiscards | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.5 | Counter | read-only | Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process. |
| CTR cdx6500LfcmTpLinkInFrames | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.3 | Counter | read-only | The number of frames that have been received by this bridge link from its segment. Note that a frame received on the interface corresponding to this bridge link is only counted by this object if and only if it is for a protocol being processed by the local bridging function. |
| INT cdx6500LfcmTpLinkMaxInfo | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.2 | INTEGER | read-only | The maximum size of the INFO (non-MAC) field that this port will receive or transmit. |
| CTR cdx6500LfcmTpLinkMLPInBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.16 | Counter | read-only | The number of frames discarded due to Multicast Link Protect being set on the incoming link. |
| CTR cdx6500LfcmTpLinkMLPOutBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.17 | Counter | read-only | The number of frames discarded due to Multicast Link Protect being set on the outgoing link. |
| CTR cdx6500LfcmTpLinkMulticastRx | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.8 | Counter | read-only | The number of Multicast Frames received on this WAN Bridge Link. |
| CTR cdx6500LfcmTpLinkMulticastTx | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.9 | Counter | read-only | The number of Multicast Frames transmitted on this WAN Bridge Link. |
| CTR cdx6500LfcmTpLinkOutBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.13 | Counter | read-only | The number of frames discarded due to transmit link state not in forwarding state. |
| CTR cdx6500LfcmTpLinkOutFrames | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.4 | Counter | read-only | The number of frames that have been transmitted by this bridge link to its segment. Note that a frame transmitted on the interface corresponding to this bridge link is only counted by this object if and only if it is for a protocol being processed by the local bridging function. |
| CTR cdx6500LfcmTpLinkULPInBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.14 | Counter | read-only | The number of frames discarded due to Unicast Link Protect being set on the incoming link. |
| CTR cdx6500LfcmTpLinkULPOutBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.15 | Counter | read-only | The number of frames discarded due to Unicast Link Protect being set on the outgoing link. |
| CTR cdx6500LfcmTpLinkUnicastRx | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.6 | Counter | read-only | The number of Unicast Frames received on this WAN Bridge Link. |
| CTR cdx6500LfcmTpLinkUnicastTx | 1.3.6.1.4.1.449.2.1.3.1.5.6.1.7 | Counter | read-only | The number of Unicast Frames transmitted on this WAN Bridge Link. |
| INT cdx6500LfcmTpPortAvailEntries | 1.3.6.1.4.1.449.2.1.3.1.5.10.2.2 | INTEGER | read-only | The number of Available Entries in the Forwarding Table. |
| INT cdx6500LfcmTpPortBridgeLinkNums | 1.3.6.1.4.1.449.2.1.2.1.6.8.1.3 | INTEGER | read-write | This is the bridge link to forward a frame with the MAC Address which is the Forwarding Table |
| CTR cdx6500LfcmTpPortBroadcastRx | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.6 | Counter | read-only | The number of Broadicast Frames received on this LAN link. |
| CTR cdx6500LfcmTpPortBroadcastTx | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.7 | Counter | read-only | The number of Broadicast Frames transmitted on this LAN link. |
| INT cdx6500LfcmTpPortIfIndex | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.1 | INTEGER | read-only | The port number of the port for which this entry contains Transparent bridging management information. |
| CTR cdx6500LfcmTpPortInboundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.8 | Counter | read-only | The number of frames discarded due to receive link state not in forwarding state . |
| INT cdx6500LfcmTpPortLearnedEntries | 1.3.6.1.4.1.449.2.1.3.1.5.10.2.1 | INTEGER | read-only | The number of end station addresses learned. |
| MAC cdx6500LfcmTpPortLocalMacAddress | 1.3.6.1.4.1.449.2.1.2.1.6.8.1.2 | MacAddress | read-write | MAC Address which is to be used for forwarding. |
| INT cdx6500LfcmTpPortMaximumEntries | 1.3.6.1.4.1.449.2.1.3.1.5.10.2.3 | INTEGER | read-only | The maximum number of entries being used in the Forwarding Table since the last node boot. |
| CTR cdx6500LfcmTpPortMLPInBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.12 | Counter | read-only | The number of frames discarded due to Multicast Link Protect being set on the incoming link. |
| CTR cdx6500LfcmTpPortMLPOutBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.13 | Counter | read-only | The number of frames discarded due to Multicast Link Protect being set on the outgoing link. |
| CTR cdx6500LfcmTpPortMulticastRx | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.4 | Counter | read-only | The number of Multicast Frames received on this LAN link. |
| CTR cdx6500LfcmTpPortMulticastTx | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.5 | Counter | read-only | The number of Multicast Frames transmitted on this LAN link. |
| CTR cdx6500LfcmTpPortOutboundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.9 | Counter | read-only | The number of frames discarded due to transmit link state not in forwarding state . |
| CTR cdx6500LfcmTpPortULPInBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.10 | Counter | read-only | The number of frames discarded due to Unicast Link Protect being set on the incoming link. |
| CTR cdx6500LfcmTpPortULPOutBoundDisc | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.11 | Counter | read-only | The number of frames discarded due to Unicast Link Protect being set on the outgoing link. |
| CTR cdx6500LfcmTpPortUnicastRx | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.2 | Counter | read-only | The number of Unicast Frames received on this LAN link. |
| CTR cdx6500LfcmTpPortUnicastTx | 1.3.6.1.4.1.449.2.1.3.1.5.2.1.3 | Counter | read-only | The number of Unicast Frames transmitted on this LAN link. |
| INT cdx6500LfcmWanDataPri | 1.3.6.1.4.1.449.2.1.2.1.6.7.1.2 | INTEGER | read-write | This parameter specifies the transmission priority of the bridged data over WAN. newvalLow : same functionality as 'low', new enumeration added for RFC1155 compatibility. |
| cdx6500LssCfg | 1.3.6.1.4.1.449.2.1.2.1.6.7.4 | |||
| cdx6500LtrmCfg | 1.3.6.1.4.1.449.2.1.2.1.6.7.3 | |||
| cdx6500PCTBasePortEntry | 1.3.6.1.4.1.449.2.1.2.1.6.10.1 | not-accessible | A list of the individual elements that make the Base Port Configurables. | |
| cdx6500PCTBasePortTable | 1.3.6.1.4.1.449.2.1.2.1.6.10 | not-accessible | This table contains Configurables for the Base Port. | |
| cdx6500PCTBridgeGroup | 1.3.6.1.4.1.449.2.1.2.1.6 | |||
| cdx6500PCTdot1dBaseLinkEntry | 1.3.6.1.4.1.449.2.1.2.1.6.9.1 | not-accessible | A list of parameters for each WAN Bridge Link. | |
| cdx6500PCTdot1dBaseLinkTable | 1.3.6.1.4.1.449.2.1.2.1.6.9 | not-accessible | This table contains WAN Bridge Link parameters, one per Bridge Link. | |
| cdx6500PCTLtrmProfEntry | 1.3.6.1.4.1.449.2.1.2.1.6.6.1 | not-accessible | A list of parameters for the Profile Table. | |
| cdx6500PCTLtrmProfTable | 1.3.6.1.4.1.449.2.1.2.1.6.6 | not-accessible | This table contains configuration for Local Termination Profile Table. | |
| cdx6500PCTLtrmStnEntry | 1.3.6.1.4.1.449.2.1.2.1.6.5.1 | not-accessible | A list of parameters for the Station Table. | |
| cdx6500PCTLtrmStnTable | 1.3.6.1.4.1.449.2.1.2.1.6.5 | not-accessible | This table contains configuration for Local Termination Station Table. | |
| cdx6500PCTNetBiosEntry | 1.3.6.1.4.1.449.2.1.2.1.6.11.1 | not-accessible | A list of the individual elements that make the Net Bios Configurables. | |
| cdx6500PCTNetBiosTable | 1.3.6.1.4.1.449.2.1.2.1.6.11 | not-accessible | This table contains Configurables for the Net Bios. | |
| cdx6500PCTPortStaticAddrEntry | 1.3.6.1.4.1.449.2.1.2.1.6.1.1 | not-accessible | A list of Source and Destination Address Actions and Bridge Link Lists for each entry. | |
| cdx6500PCTPortStaticAddrTable | 1.3.6.1.4.1.449.2.1.2.1.6.1 | not-accessible | This table contains MAC Address filtering configuration information. | |
| cdx6500PCTPortStaticProtEntry | 1.3.6.1.4.1.449.2.1.2.1.6.2.1 | not-accessible | This is a list of configurable information for each Protocol Filtering Table entry. The parameters include Protocol Type, Protocol Value, link actions and Bridge Link lists. | |
| cdx6500PCTPortStaticProtTable | 1.3.6.1.4.1.449.2.1.2.1.6.2 | not-accessible | This table contains Protocol Filtering Configuration Information. | |
| cdx6500PCTSrLinkEntry | 1.3.6.1.4.1.449.2.1.2.1.6.3.1 | not-accessible | A list of information for each WAN Bridge Link of a source route bridge. | |
| cdx6500PCTSrLinkTable | 1.3.6.1.4.1.449.2.1.2.1.6.3 | not-accessible | A table that contains configuration information about every WAN Bridge Link that is associated with this source route bridge. | |
| cdx6500PCTStaticLinkEntry | 1.3.6.1.4.1.449.2.1.2.1.6.4.1 | not-accessible | Filtering information configured into the bridge by (local or network) management specifying the set of WAN Bridge Links to which frames received from a specific bridge link and containing a specific destination address are allowed to be forwarded. | |
| cdx6500PCTStaticLinkTable | 1.3.6.1.4.1.449.2.1.2.1.6.4 | not-accessible | A table containing filtering information configured into the bridge by (local or network) management specifying the set of WAN Bridge Links to which frames received from specific links and containing specific destination addresses are allowed to be forwarded. The value of zero in this table as the WAN Bridge Link from which frames with a specific destination address are received, is used to specify all links for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast and for group/broadcast addresses. | |
| cdx6500PCTTbPermEntry | 1.3.6.1.4.1.449.2.1.2.1.6.8.1 | not-accessible | A list of the individual elements that make the entries of the Permanent MAC Address table | |
| cdx6500PCTTbPermTable | 1.3.6.1.4.1.449.2.1.2.1.6.8 | not-accessible | This table contains Permanent MAC Address that are loaded into the Forwarding Table after a table or node boot. | |
| cdx6500PSTBaseLinkEntry | 1.3.6.1.4.1.449.2.1.3.1.5.4.1 | not-accessible | A list of controls and statistics for each WAN Bridge Links. | |
| cdx6500PSTBaseLinkTable | 1.3.6.1.4.1.449.2.1.3.1.5.4 | not-accessible | This table contains statistics for the WAN Bridge Links. | |
| cdx6500PSTBridgeGroup | 1.3.6.1.4.1.449.2.1.3.1.5 | |||
| cdx6500PSTLtrmStatsEntry | 1.3.6.1.4.1.449.2.1.3.1.5.9.1 | not-accessible | A list of statistics and boot control per Local Termination session. | |
| cdx6500PSTLtrmStatsTable | 1.3.6.1.4.1.449.2.1.3.1.5.9 | not-accessible | This table contains Local Termination session statistics. | |
| cdx6500PSTPortBasePortEntry | 1.3.6.1.4.1.449.2.1.3.1.5.11.1 | not-accessible | A list of information for each port of the bridge. | |
| cdx6500PSTPortBaseTable | 1.3.6.1.4.1.449.2.1.3.1.5.11 | not-accessible | A table that contains generic information about every port that is associated with this bridge. Transparent, source-route, and srt ports are included. | |
| cdx6500PSTPortFilterEntry | 1.3.6.1.4.1.449.2.1.3.1.5.3.1 | not-accessible | A list of filtering statistcs for MAC Address and Protocol filtering. | |
| cdx6500PSTPortFilterTable | 1.3.6.1.4.1.449.2.1.3.1.5.3 | not-accessible | This table contains MAC Address and Protocol Filtering information. | |
| cdx6500PSTSrLinkEntry | 1.3.6.1.4.1.449.2.1.3.1.5.5.1 | not-accessible | A list of information for each WAN Bridge Link of a source route bridge. | |
| cdx6500PSTSrLinkTable | 1.3.6.1.4.1.449.2.1.3.1.5.5 | not-accessible | A table that contains information about every WAN Bridge Link that is associated with this source route bridge. | |
| cdx6500PSTSrPortEntry | 1.3.6.1.4.1.449.2.1.3.1.5.1.1 | not-accessible | A list of information for each port of a source route bridge. | |
| cdx6500PSTSrPortTable | 1.3.6.1.4.1.449.2.1.3.1.5.1 | not-accessible | A table that contains information about every port that is associated with this source route bridge. | |
| cdx6500PSTStaticsStatsLinkEntry | 1.3.6.1.4.1.449.2.1.3.1.5.8.1 | not-accessible | A list of filtering statistcs for MAC Address and Protocol filtering. | |
| cdx6500PSTStaticStatsLinkTable | 1.3.6.1.4.1.449.2.1.3.1.5.8 | not-accessible | This table contains MAC Address and Protocol Filtering information. | |
| cdx6500PSTStpLinkEntry | 1.3.6.1.4.1.449.2.1.3.1.5.7.1 | not-accessible | A list of information maintained by every bridge link about the Spanning Tree Protocol state for that bridge link. | |
| cdx6500PSTStpLinkTable | 1.3.6.1.4.1.449.2.1.3.1.5.7 | not-accessible | A table that contains bridge-Link-specific information for the Spanning Tree Protocol. | |
| cdx6500PSTTpLinkEntry | 1.3.6.1.4.1.449.2.1.3.1.5.6.1 | not-accessible | A list of information for each bridge link of a transparent bridge. | |
| cdx6500PSTTpLinkTable | 1.3.6.1.4.1.449.2.1.3.1.5.6 | not-accessible | A table that contains information about every bridge link that is associated with this transparent bridge. | |
| cdx6500PSTTpPortEntry | 1.3.6.1.4.1.449.2.1.3.1.5.2.1 | not-accessible | A list of information for each port of a transparent bridge. | |
| cdx6500PSTTpPortTable | 1.3.6.1.4.1.449.2.1.3.1.5.2 | not-accessible | A table that contains information about every port that is associated with this transparent bridge. | |
| cdx6500Statistics | 1.3.6.1.4.1.449.2.1.3 | |||
| cdx6500StatProtocolGroup | 1.3.6.1.4.1.449.2.1.3.1 | |||
| cdxProductSpecific | 1.3.6.1.4.1.449.2 | |||
| codex | 1.3.6.1.4.1.449 |
RFC description
Manages bridge MAC filtering and static address tables on Codex CDX6500 data networking equipment.
Start monitoring Motorola Codex 6500-series data/statistical multiplexer (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.