All MIBs › BIANCA-BOX-ISDN-MIB
Category: Telephony and VoIP, Vendor: bintec
Description: Manages ISDN B-channel and D-channel configuration and call statistics on the bintec BIANCA/BRICK router.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is BIANCA-BOX-ISDN-MIB?
This is a vendor MIB for the BIANCA/BRICK family of ISDN routers, originally from BinTec and later Bianca-Systems/bintec, intended to manage and monitor ISDN B-channel and D-channel configuration along with call statistics on the device. It would expose configuration objects for ISDN interface parameters as well as counters related to call setup, duration, and channel usage across the router's ISDN ports. Given its focus on ISDN connectivity, it is aimed at monitoring the hardware/interface status of ISDN ports, i.e. channel state and call activity, which is central to diagnosing WAN link availability and call failures on this dial/leased-line ISDN router. It is a self-contained enterprise MIB, though it conceptually parallels the general concept of standard ISDN management, without a documented formal dependency here. It would be deployed on small/branch-office bintec BIANCA/BRICK ISDN routers, where an administrator monitors channel and call state to troubleshoot ISDN WAN connectivity issues after completing a BIANCA-BOX-ISDN-MIB download to load the module into a MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in BIANCA-BOX-ISDN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- bintec BIANCA/BRICK ISDN router
Monitoring Examples
No sample object names or module description text were provided for this MIB, so specific table/object-level detail cannot be given honestly; based on the short description alone, it would expose ISDN B-channel/D-channel configuration and call-statistics objects on bintec BIANCA/BRICK routers, but concrete object identifiers are not confirmed here.
This MIB depends on
Related MIBs
Imported Objects
From RFC1155-SMI
| Counter | |
| OBJECT-TYPE | |
| TimeTicks |
From SNMPv2-TC
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| bibo | 1.3.6.1.4.1.272.4 | |||
| bintec | 1.3.6.1.4.1.272 | |||
| dod | 1.3.6 | |||
| enterprises | 1.3.6.1.4.1 | |||
| internet | 1.3.6.1 | |||
| isdn | 1.3.6.1.4.1.272.4.2 | |||
| STR isdnAccountingTemplate | 1.3.6.1.4.1.272.4.2.7 | DisplayString | read-write | Specifies the format of accounting messages sent by the syslog protocol. The format can consist of any order of the following variables. Tag Meaning %S Date the connection opened; in DD.MM.YY format. %s Time the connection was established: in HH:MM:SS format %R Date the connection closed; in DD.MM.YY format. %r Time the connection was closed: in HH:MM:SS format. %d The duration of the connection in seconds. %D Call identification: internal/external, ID, slot/unit (PABX only) %P Call classification: Private/Business, project number (PABX only) %y Total number of bytes received over the connection. %Y Total number of bytes sent over the connection. %g Total packets received over the connection %G Total packets sent over the connection. %c Total number of charging units (value) incurred for the connection. %C Total number of charging units (string) incurred for the connection. %n The call's direction; either incoming (I) or outgoing (O). %Z The local address (Calling or Called party's number, see %n). %z The local subaddress (Calling or Called party's number, see %n). %T The remote address (Calling or Called party's number %n). %t The remote subaddress (Calling or Called party's number %n). %i Service indicator and additional information for the call. %b Bearer capability for the call. %l Low layer capability for the call. %h High layer capability for the call. %u DSS1 error cause, if applicable. %U 1tr6 error cause, if applicable. %L Local (internal) error cause. %F Call reference (internal). %e Calling extension (for call assiciation; PABX only) %I Information about the subsystem the call was given to. The default accounting template setting contains the following tags: %S,%s,%r,%d,%y,%Y,%g,%G,%C,%n,%Z,%T,%i,%u,%L,%I. This template produces accounting messages similar to the following. ISDN:18.08.1997,13:53:19,13:53:34,12,1096,1875,33,33,1Units,O,2,091196730,7/0,9F,0 |
| INT isdnCallAddInfo | 1.3.6.1.4.1.272.4.2.4.1.14 | INTEGER | read-only | Additional information that was sent on the ISDN D-channel when the call was established. Only sent/received when using the 1TR6 protocol. |
| TIK isdnCallAge | 1.3.6.1.4.1.272.4.2.4.1.4 | TimeTicks | read-only | The age of the call. For outgoing calls, the time since the call began, or for incoming calls, the time since the call was received. The format is in hh:mm:ss.00. |
| OCT isdnCallBC | 1.3.6.1.4.1.272.4.2.4.1.15 | OCTET STRING | read-only | Bearer Capability that was sent on the ISDN D-channel when the call was established. |
| INT isdnCallChannel | 1.3.6.1.4.1.272.4.2.4.1.7 | INTEGER | read-only | The corresponding B-channel on this ISDN interface. Refer to the isdnIfTable. |
| INT isdnCallCharge | 1.3.6.1.4.1.272.4.2.4.1.18 | INTEGER | read-only | This object contains the charge for this call either as units or as 1/1000 of the respective currency. Which type of information is choosen, depends on the information provided by the ISDN service provide. See also ChargeInfo for textual information. |
| STR isdnCallChargeInfo | 1.3.6.1.4.1.272.4.2.4.1.25 | DisplayString | read-only | Textual information of charge, i.e. 0.12 DM or 3 units |
| INT isdnCallDspItem | 1.3.6.1.4.1.272.4.2.4.1.8 | INTEGER | read-only | The item to or from which this call is connected. For any routing tasks (IP, IPX, X.25, bridging, ...) the ppp(1) item is used. For the isdnlogin program, login(2) is used. For CAPI 1.1 programs, the items eaz0(48) .. eaz9(57) are used. |
| isdnCallEntry | 1.3.6.1.4.1.272.4.2.4.1 | not-accessible | ||
| HEX isdnCallHistory1TR6Cause | 1.3.6.1.4.1.272.4.2.8.1.19 | HexValue | read-only | ISDN error condition reported by the 1TR6 protocol, for National ISDN in Germany. See Appendix C in the User's Guide. |
| INT isdnCallHistoryAddInfo | 1.3.6.1.4.1.272.4.2.8.1.13 | INTEGER | read-only | Additional information that was sent on the ISDN D-channel when the call was established. Only sent/received when using the 1TR6 protocol. |
| OCT isdnCallHistoryBC | 1.3.6.1.4.1.272.4.2.8.1.14 | OCTET STRING | read-only | Bearer Capability that was sent on the ISDN D-channel when the call was established. |
| INT isdnCallHistoryChannel | 1.3.6.1.4.1.272.4.2.8.1.6 | INTEGER | read-only | The corresponding B-channel on this ISDN interface. |
| INT isdnCallHistoryCharge | 1.3.6.1.4.1.272.4.2.8.1.17 | INTEGER | read-only | The number of charging ticks received for this connection. Actual charges can be computed by multiplying this value with the unit price, e.g. .12 DM in Germany. If you aren't receiving charging information for outgoing calls, verify with your local ISDN provider to make sure this option being provided/is available. As an option, this Object may contain the charge measured in 1/1000 of the respective currency. See also ChargeInfo for textual information. |
| STR isdnCallHistoryChargeInfo | 1.3.6.1.4.1.272.4.2.8.1.21 | DisplayString | read-only | Textual information of charge, i.e. 0.12 DM or 3 units |
| INT isdnCallHistoryDspItem | 1.3.6.1.4.1.272.4.2.8.1.7 | INTEGER | read-only | The item this call was connected to. Routing tasks (IP, IPX, X.25, bridging, ...) use ppp(1). The isdnlogin program uses login(2). CAPI 1.1 programs, use the items eaz0(48) .. eaz9(57) are used. |
| HEX isdnCallHistoryDSS1Cause | 1.3.6.1.4.1.272.4.2.8.1.18 | HexValue | read-only | ISDN error condition reported by the DSS1 protocol, for Euro ISDN. See Appendix C in the User's Guide. |
| INT isdnCallHistoryDuration | 1.3.6.1.4.1.272.4.2.8.1.4 | INTEGER | read-only | The duration of the call in seconds. |
| isdnCallHistoryEntry | 1.3.6.1.4.1.272.4.2.8.1 | not-accessible | ||
| OCT isdnCallHistoryHLC | 1.3.6.1.4.1.272.4.2.8.1.16 | OCTET STRING | read-only | High Layer Capability that was sent on the ISDN D-channel when the call was established. |
| STR isdnCallHistoryInfo | 1.3.6.1.4.1.272.4.2.8.1.23 | DisplayString | read-only | Additional information to identify the call |
| INT isdnCallHistoryIsdnIfIndex | 1.3.6.1.4.1.272.4.2.8.1.5 | INTEGER | read-only | The corresponding ISDN interface that this call used. |
| OCT isdnCallHistoryLLC | 1.3.6.1.4.1.272.4.2.8.1.15 | OCTET STRING | read-only | Low Layer Capability that was sent on the ISDN D-channel when the call was established. |
| INT isdnCallHistoryLocalCause | 1.3.6.1.4.1.272.4.2.8.1.20 | INTEGER | read-only | ISDN error condition reported by the system locally. See Appendix C in the User's Guide. |
| STR isdnCallHistoryLocalNumber | 1.3.6.1.4.1.272.4.2.8.1.10 | DisplayString | read-only | The calling party number that was sent (with the outgoing call) or was received (with incoming calls). |
| OCT isdnCallHistoryLocalSubaddress | 1.3.6.1.4.1.272.4.2.8.1.11 | OCTET STRING | read-only | The subaddress of the calling party number. |
| CTR isdnCallHistoryReceivedErrors | 1.3.6.1.4.1.272.4.2.8.1.26 | Counter | read-only | Count of received invalid HDLC Frames. |
| CTR isdnCallHistoryReceivedOctets | 1.3.6.1.4.1.272.4.2.8.1.25 | Counter | read-only | Count of received valid HDLC Octets. |
| CTR isdnCallHistoryReceivedPackets | 1.3.6.1.4.1.272.4.2.8.1.24 | Counter | read-only | Count of received valid HDLC Frames. |
| STR isdnCallHistoryRemoteNumber | 1.3.6.1.4.1.272.4.2.8.1.8 | DisplayString | read-only | The ISDN number that was called (for outgoing calls) or was calling (for incoming calls). |
| OCT isdnCallHistoryRemoteSubaddress | 1.3.6.1.4.1.272.4.2.8.1.9 | OCTET STRING | read-only | The subaddress of the remote number. See isdnCall- HistoryRemoteNumber. |
| INT isdnCallHistoryScreening | 1.3.6.1.4.1.272.4.2.8.1.22 | INTEGER | read-only | Screening Indicator of the calling party number of incoming calls. The calling partys number (CPN) may be assigned either by the user placing the call or by the telephone switching station. If the CPN was assigned by the user the switching station may optionally verify the address. indicator: CPN assigned: verification: `user' by user none `user-verified' by user verification successful `user-failed' by user verification failed `network' by network none |
| INT isdnCallHistoryServiceIndicator | 1.3.6.1.4.1.272.4.2.8.1.12 | INTEGER | read-only | Service indicator that was sent on the ISDN D-channel when the call was established. |
| INT isdnCallHistoryStkNumber | 1.3.6.1.4.1.272.4.2.8.1.1 | INTEGER | read-only | The number of the ISDN-Stack, this call went through. |
| isdnCallHistoryTable | 1.3.6.1.4.1.272.4.2.8 | not-accessible | The isdnCallHistoryTable contains information pertaining to the last 20 ISDN calls made, since the last system startup. Each call that appears in the isdnCallTable, will have its information stored here (temporarily), once it disconnects. Creating entries: Entries are added by the system once a call is disconnected. Deleting entries: Entries are removed by the system. The table is designed as a circular queue (or FIFO); the most calls are stored at inx 19 with older calls rolling off the top of the table at inx 00. | |
| DAT isdnCallHistoryTime | 1.3.6.1.4.1.272.4.2.8.1.3 | Date | read-only | The time the call was received (incoming) or was placed (outgoing). |
| CTR isdnCallHistoryTransmitErrors | 1.3.6.1.4.1.272.4.2.8.1.29 | Counter | read-only | Count of transmit errors (Collision, TX underrun). |
| CTR isdnCallHistoryTransmitOctets | 1.3.6.1.4.1.272.4.2.8.1.28 | Counter | read-only | Count of transmitted Octets. |
| CTR isdnCallHistoryTransmitPackets | 1.3.6.1.4.1.272.4.2.8.1.27 | Counter | read-only | Count of transmitted HDLC Frames. |
| INT isdnCallHistoryType | 1.3.6.1.4.1.272.4.2.8.1.2 | INTEGER | read-only | The direction of the call, incoming or outgoing. |
| OCT isdnCallHLC | 1.3.6.1.4.1.272.4.2.4.1.17 | OCTET STRING | read-only | The number of charging ticks received since this connection was established. Actual charges can be computed by multiplying this value with the unit price (e.g. .12 DM in Germany). If you aren't receiving charging information for outgoing calls, verify with your local ISDN provider to make sure this option is being provided/is available. |
| STR isdnCallInfo | 1.3.6.1.4.1.272.4.2.4.1.27 | DisplayString | read-only | Additional information to identify the call |
| INT isdnCallIsdnIfIndex | 1.3.6.1.4.1.272.4.2.4.1.6 | INTEGER | read-only | The corresponding ISDN interface that is used for this call. Refer to the isdnIfTable. |
| OCT isdnCallLLC | 1.3.6.1.4.1.272.4.2.4.1.16 | OCTET STRING | read-only | Low Layer Capability that was sent on the ISDN D-channel when the call was established. |
| STR isdnCallLocalNumber | 1.3.6.1.4.1.272.4.2.4.1.11 | DisplayString | read-only | The calling party number that was sent (with the outgoing call) or was received (with incoming calls). Refer to the isdnStkTable. |
| OCT isdnCallLocalSubaddress | 1.3.6.1.4.1.272.4.2.4.1.12 | OCTET STRING | read-only | The subaddress of the calling party number. See isdnCallRLocalNumber. |
| CTR isdnCallReceivedErrors | 1.3.6.1.4.1.272.4.2.4.1.21 | Counter | read-only | Count of received invalid HDLC Frames. |
| CTR isdnCallReceivedOctets | 1.3.6.1.4.1.272.4.2.4.1.20 | Counter | read-only | Count of received valid HDLC Octets. |
| CTR isdnCallReceivedPackets | 1.3.6.1.4.1.272.4.2.4.1.19 | Counter | read-only | Count of received valid HDLC Frames. |
| INT isdnCallReference | 1.3.6.1.4.1.272.4.2.4.1.3 | INTEGER | read-only | The corresponding Call-Reference Value on the ISDN D-channel. |
| STR isdnCallRemoteNumber | 1.3.6.1.4.1.272.4.2.4.1.9 | DisplayString | read-only | The ISDN number that was called (for outgoing calls) or was calling (for incoming calls). |
| OCT isdnCallRemoteSubaddress | 1.3.6.1.4.1.272.4.2.4.1.10 | OCTET STRING | read-only | The subaddress of the remote number. The subaddress is coded in NSAP format as octets. See isdnCallRemoteNumber. |
| INT isdnCallScreening | 1.3.6.1.4.1.272.4.2.4.1.26 | INTEGER | read-only | Screening Indicator of the calling party number of incoming calls. The calling partys number (CPN) may be assigned either by the user placing the call or by the telephone switching station. If the CPN was assigned by the user the switching station may optionally verify the address. indicator: CPN assigned: verification: `user' by user none `user-verified' by user verification successful `user-failed' by user verification failed `network' by network none |
| INT isdnCallServiceIndicator | 1.3.6.1.4.1.272.4.2.4.1.13 | INTEGER | read-only | Service indicator that was sent on the ISDN D-channel when the call was established. |
| INT isdnCallState | 1.3.6.1.4.1.272.4.2.4.1.5 | INTEGER | read-write | The state of the call. |
| INT isdnCallStkNumber | 1.3.6.1.4.1.272.4.2.4.1.1 | INTEGER | read-only | The number of the ISDN-Stack, this call is going through. Refer to the isdnStkTable. |
| isdnCallTable | 1.3.6.1.4.1.272.4.2.4 | not-accessible | The isdnCallTable displays all currently active ISDN calls (incoming and outgoing). Only the system can add or remove entries to this table. Creating entries: Entries are added when an outgoing call is made or when an incoming call is connected. Deleting entries: Entries are removed once the respective call is disconnected. | |
| CTR isdnCallTransmitErrors | 1.3.6.1.4.1.272.4.2.4.1.24 | Counter | read-only | Count of transmit errors (Collision, TX underrun). |
| CTR isdnCallTransmitOctets | 1.3.6.1.4.1.272.4.2.4.1.23 | Counter | read-only | Count of transmitted Octets. |
| CTR isdnCallTransmitPackets | 1.3.6.1.4.1.272.4.2.4.1.22 | Counter | read-only | Count of transmitted HDLC Frames. |
| INT isdnCallType | 1.3.6.1.4.1.272.4.2.4.1.2 | INTEGER | read-only | The direction of the call. |
| INT isdnChBundle | 1.3.6.1.4.1.272.4.2.2.1.5 | INTEGER | read-write | Index of the bundle to aggregate multiple Channels to one interface. Not valid in dialup mode. |
| isdnChEntry | 1.3.6.1.4.1.272.4.2.2.1 | not-accessible | ||
| INT isdnChIsdnIfIndex | 1.3.6.1.4.1.272.4.2.2.1.1 | INTEGER | read-only | Unique index of an Interface. |
| INT isdnChNumber | 1.3.6.1.4.1.272.4.2.2.1.2 | INTEGER | read-only | The channel number. 0 is D-channel, 1..2 are the B- channels of a BRI module, and 1..31 are the B-channels of a PRI module. |
| CTR isdnChReceivedErrors | 1.3.6.1.4.1.272.4.2.2.1.9 | Counter | read-only | Count of received valid errors (can be detected by HDLC-Checksum-Errors). |
| CTR isdnChReceivedOctets | 1.3.6.1.4.1.272.4.2.2.1.8 | Counter | read-only | Count of received valid HDLC bytes. |
| CTR isdnChReceivedPackets | 1.3.6.1.4.1.272.4.2.2.1.7 | Counter | read-only | Count of received valid HDLC Frames. |
| INT isdnChState | 1.3.6.1.4.1.272.4.2.2.1.3 | INTEGER | read-only | Status of the Channel controlled either by the call control protocol or the physical state of the interface. |
| isdnChTable | 1.3.6.1.4.1.272.4.2.2 | not-accessible | The isdnChTable contains information for each physical B or D channel on the system. The entries contain information regarding the configuration of the channel and various statistical data for active connections. Only the system can add entries to this table. Creating entries: Entries are created by the system when a new interface appears in the isdnIfTable; when a new BRI or PRI module is installed. Deleting entries: Are not possible. | |
| INT isdnChThroughput | 1.3.6.1.4.1.272.4.2.2.1.6 | INTEGER | read-only | Throughput of the channel in bits/second (64000 for B-channels, 16000 for BRI D-Channels. |
| CTR isdnChTransmitErrors | 1.3.6.1.4.1.272.4.2.2.1.12 | Counter | read-only | Count of transmitted valid HDLC errors. Can occur when the transmitter can not be reloaded fast enough when transmitting large packets. This should only happen when the system is over encumbered. |
| CTR isdnChTransmitOctets | 1.3.6.1.4.1.272.4.2.2.1.11 | Counter | read-only | Count of received valid HDLC Frames. |
| CTR isdnChTransmitPackets | 1.3.6.1.4.1.272.4.2.2.1.10 | Counter | read-only | Count of received valid HDLC Frames. |
| INT isdnChType | 1.3.6.1.4.1.272.4.2.2.1.4 | INTEGER | read-write | Type of Channel.Setting this object to one of the leased values creates a new entry in the ifTable. |
| INT isdnCreditsCurrentInCon | 1.3.6.1.4.1.272.4.2.12.1.10 | INTEGER | read-only | Current number of incoming connections. |
| INT isdnCreditsCurrentOutCon | 1.3.6.1.4.1.272.4.2.12.1.11 | INTEGER | read-only | Current number of outgoing connections. |
| isdnCreditsEntry | 1.3.6.1.4.1.272.4.2.12.1 | not-accessible | ||
| INT isdnCreditsMaxCharge | 1.3.6.1.4.1.272.4.2.12.1.6 | INTEGER | read-write | Maximum allowed charge amount during the observation interval. -1 disables this limit. |
| INT isdnCreditsMaxCurrentCon | 1.3.6.1.4.1.272.4.2.12.1.20 | INTEGER | read-write | Maximum number of currently allowed connections in both directions. -1 disables this limit. |
| INT isdnCreditsMaxCurrentInCon | 1.3.6.1.4.1.272.4.2.12.1.18 | INTEGER | read-write | Maximum number of currently allowed incoming connections. -1 disables this limit. |
| INT isdnCreditsMaxCurrentOutCon | 1.3.6.1.4.1.272.4.2.12.1.19 | INTEGER | read-write | Maximum number of currently allowed outgoing connections. -1 disables this limit. |
| INT isdnCreditsMaxInCon | 1.3.6.1.4.1.272.4.2.12.1.4 | INTEGER | read-write | Maximum number of allowed incoming connections during the observation interval. -1 disables this limit. |
| INT isdnCreditsMaxInDuration | 1.3.6.1.4.1.272.4.2.12.1.7 | INTEGER | read-write | Maximum connect time for incoming connections in seconds during the observation interval. -1 disables this limit. |
| INT isdnCreditsMaxOutCon | 1.3.6.1.4.1.272.4.2.12.1.5 | INTEGER | read-write | Maximum number of allowed outgoing connections during the observation interval. -1 disables this limit. |
| INT isdnCreditsMaxOutDuration | 1.3.6.1.4.1.272.4.2.12.1.8 | INTEGER | read-write | Maximum connect time for outgoing connections in seconds during the observation interval. -1 disables this limit |
| INT isdnCreditsMeasuretime | 1.3.6.1.4.1.272.4.2.12.1.3 | INTEGER | read-write | Time of one observation interval in seconds. |
| INT isdnCreditsSubsysNumber | 1.3.6.1.4.1.272.4.2.12.1.1 | INTEGER | read-only | Type of Subsystem. |
| INT isdnCreditsSurveillance | 1.3.6.1.4.1.272.4.2.12.1.2 | INTEGER | read-write | Surveillance on or off. |
| isdnCreditsTable | 1.3.6.1.4.1.272.4.2.12 | not-accessible | The isdnCreditsTable contains informations about current used resources and maximum allowed resources for each during a specified interval subsystem. Creating entries: Entries are added by the system during startup. Deleting entries: Is not possible. | |
| INT isdnCreditsTimeleft | 1.3.6.1.4.1.272.4.2.12.1.9 | INTEGER | read-write | Time in seconds left in current interval. Writing to Timeleft will restart the observation interval. |
| INT isdnCreditsTotalCharge | 1.3.6.1.4.1.272.4.2.12.1.15 | INTEGER | read-only | Total accounted charge during the observation interval. |
| INT isdnCreditsTotalInCon | 1.3.6.1.4.1.272.4.2.12.1.12 | INTEGER | read-only | Total count of incoming connections during the observation interval. |
| INT isdnCreditsTotalInDuration | 1.3.6.1.4.1.272.4.2.12.1.16 | INTEGER | read-only | Total connect time of incoming connections during the observation interval. |
| INT isdnCreditsTotalMaxCon | 1.3.6.1.4.1.272.4.2.12.1.14 | INTEGER | read-only | Maximum number of simultaniously established connections during the observation interval. |
| INT isdnCreditsTotalOutCon | 1.3.6.1.4.1.272.4.2.12.1.13 | INTEGER | read-only | Total count of outgoing connections during the observation interval. |
| INT isdnCreditsTotalOutDuration | 1.3.6.1.4.1.272.4.2.12.1.17 | INTEGER | read-only | Total connect time of outgoing connections during the observation interval. |
| isdnDChanX31Entry | 1.3.6.1.4.1.272.4.2.6.1 | not-accessible | ||
| isdnDChanX31Table | 1.3.6.1.4.1.272.4.2.6 | not-accessible | The isdnDChanX31Table contains information for the X.31 stack for each available ISDN D-channel. This information is mainly used for X.25 packet-switching functions but can be used for CAPI applications. The table is initialized during the auto configure process. By default the system polls each D-channel for an assigned TEI (terminal endpoint identifier). Creating entries: Entries can be added by assigning a new value (valid IfIndex) to isdnX31IsdnIfIndex. Deleting entries: Entries are removed by assigning 'delete' to the approprate isdnX31IsdnAssignedTo object. | |
| isdnDispatchEntry | 1.3.6.1.4.1.272.4.2.5.1 | not-accessible | ||
| isdnDispatchTable | 1.3.6.1.4.1.272.4.2.5 | not-accessible | The isdnDispatchTable is the central distribution center for all incoming ISDN connections. Incoming ISDN connections are `dispatched' to a service (isdnDspItem) based on the calling party's number sent over the ISDN. Creating entries: Entries can be created by assigning a value to both the isdnDspStkNumber and isdnDspItem objects within one operation. Deleting entries: Entries are removed by setting the isdnDspItem to 'delete'. | |
| INT isdnDspBearer | 1.3.6.1.4.1.272.4.2.5.1.5 | INTEGER | read-write | The isdnDspBearer is used for dispatching different types of calls |
| INT isdnDspDirection | 1.3.6.1.4.1.272.4.2.5.1.8 | INTEGER | read-write | Specifies whether the entry is to be used for outgoing calls, incoming calls or both. |
| INT isdnDspItem | 1.3.6.1.4.1.272.4.2.5.1.2 | INTEGER | read-write | The item to connect this call to. Routing tasks (IP, IPX, X.25, bridging, ...) should use the ppp(1). For the isdnlogin program use the login(2) item. For CAPI 1.1 programs, use items eaz0(48) .. eaz9(57). |
| STR isdnDspLocalNumber | 1.3.6.1.4.1.272.4.2.5.1.3 | DisplayString | read-write | If the Called Party Number of the incoming call on the specified ISDN stack matches this value, the call is dispatched to the defined item. For outgoing calls from this item, the local number is sent as the Calling Party Number. Note: The matching of isdnDspLocalNumber value is done from right to left based on the number of digits in isdnDspLocalNumber. For example: if isdnDspLocalNumber is set to 124 then an incoming Called Party Number of 6501124 would match while one with 650024 would not. |
| OCT isdnDspLocalSubaddress | 1.3.6.1.4.1.272.4.2.5.1.4 | OCTET STRING | read-write | If the Called Party Subaddress of the incoming call on the specified ISDN stack matches this value, the call is dispatched to the defined item. For outgoing calls from this item, the local subaddress is sent as the Calling Party Subaddress. Note: The matching of isdnDspLocalSubaddress values is done by comparing the entire string of numbers in the Called Party Subaddress field. For example: if issdnDspLocalSubaddress is set to 072522 then only calls with an incoming Called Party Subaddress of 072522 would match, i.e. one with 522 would not match. |
| INT isdnDspMode | 1.3.6.1.4.1.272.4.2.5.1.9 | INTEGER | read-write | This object specifies the matching direction for incoming calls. When set to right-to-left, the rightmost digits of the called address of an incoming call are compared against the LocalNumber. This is useful for normal basic rate interfaces without DDI, because only few last digits have to be specified to be unique. When set to left-to-right, the leftmost digits of an incoming call are compared against the LocalNumber. Only the latter mode may be used for direct dialing in (DDI). |
| INT isdnDspSlot | 1.3.6.1.4.1.272.4.2.5.1.6 | INTEGER | read-write | Identification number of the used slot. |
| INT isdnDspStkNumber | 1.3.6.1.4.1.272.4.2.5.1.1 | INTEGER | read-write | The ISDN stack number for this entry. |
| INT isdnDspUnit | 1.3.6.1.4.1.272.4.2.5.1.7 | INTEGER | read-write | Identification number of the used unit. |
| STR isdnDspUserName | 1.3.6.1.4.1.272.4.2.5.1.10 | DisplayString | read-write | The name of the user. |
| INT isdnHistoryMaxEntries | 1.3.6.1.4.1.272.4.2.10 | INTEGER | read-write | Maximum number of isdnCallHistory entries in memory. |
| CTR isdnIfActivates | 1.3.6.1.4.1.272.4.2.1.1.11 | Counter | read-only | Number of successful activation cycles during lifetime of the system. |
| INT isdnIfActivationRequest | 1.3.6.1.4.1.272.4.2.1.1.5 | INTEGER | read-write | When this object is set to 'activate' the BRICK will start an activation sequence of ISDN-Layer1 of the basic rate interface. |
| INT isdnIfAutoconfig | 1.3.6.1.4.1.272.4.2.1.1.14 | INTEGER | read-write | Start Autoconfiguration on this ISDN interface at bootup. |
| INT isdnIfAutoconfigState | 1.3.6.1.4.1.272.4.2.1.1.13 | INTEGER | read-write | Start auto configuration on this ISDN Interface. Auto configuration is a mechanism to automatically detect the attributes of an ISDN interface. This can be done at boot time (if isdnIfAutoConfig is set to 'on') or by manually setting this field to 'start'. Refer to Chapter 3 on Features and Methods. |
| INT isdnIfBchannelControl | 1.3.6.1.4.1.272.4.2.1.1.4 | INTEGER | read-only | B-channels are controlled by a call control protocol in the D-channel. Otherwise they may be used as permanent links. |
| CTR isdnIfDeactivates | 1.3.6.1.4.1.272.4.2.1.1.12 | Counter | read-only | Number of deactivations during lifetime of the system. |
| STR isdnIfDescription | 1.3.6.1.4.1.272.4.2.1.1.2 | DisplayString | read-only | Textual description of the basic rate interface including its slot and number (e.g. bri2-0 means slot 2, unit 0). |
| isdnIfEntry | 1.3.6.1.4.1.272.4.2.1.1 | not-accessible | ||
| INT isdnIfIndex | 1.3.6.1.4.1.272.4.2.1.1.1 | INTEGER | read-only | Unique index of the basic or primary rate interface. |
| INT isdnIfLayer1State | 1.3.6.1.4.1.272.4.2.1.1.3 | INTEGER | read-only | The ISDN physical layer state according to I.430 f1(1) = inactive; f2(2) = sensing; f3(3) = deactivated; f4(4) = awaiting signal; f5(5) = identifying input; f6(6) = synchronized; f7(7) = activated; f8(8) = lost framing; g1(9) = deactive; g2(10) = pending activation; g3(11) = active; g4(12) = pending deactivation |
| INT isdnIfMode | 1.3.6.1.4.1.272.4.2.1.1.6 | INTEGER | read-write | Specifies the mode of the interface. TE or NT Mode will be set for ISDN interfaces without PABX control. For PRI both NT (network termination) and TE (terminal equipment) modes are supported. |
| INT isdnIfNumberOfChannels | 1.3.6.1.4.1.272.4.2.1.1.9 | INTEGER | read-only | Number of Channels including the D channel, that are available on this ISDN Interface (3 = BRI, 31 = PRI). |
| CTR isdnIfSlips | 1.3.6.1.4.1.272.4.2.1.1.21 | Counter | read-only | Slip conditions detected since startup. Flags that the frequency of receive clock is different than frequency of internal system clock. |
| isdnIfTable | 1.3.6.1.4.1.272.4.2.1 | not-accessible | The isdnIfTable contains information relating to the interfaces found on the system. Each entry corresponds to a connected ISDN interface (BRI or PRI). Entries can only be added or deleted by the system. Creating entries: Entries are created by the system only when a new BRI or PRI module is installed. Deleting entries: Entries are removed by the system after the appropriate BRI or PRI module is removed. | |
| CTR isdnIfTimeouts | 1.3.6.1.4.1.272.4.2.1.1.10 | Counter | read-only | Number of timeouts of T3 during lifetime of the system. |
| INT isdnIfTimerT3 | 1.3.6.1.4.1.272.4.2.1.1.7 | INTEGER | read-write | Value of Timer T3 in milliseconds.T3 is started whenever ISDNLayer-1 is activated (i.e. Activation Request is started). |
| INT isdnIfUsePowerDetector | 1.3.6.1.4.1.272.4.2.1.1.8 | INTEGER | read-write | Use the PS1 Power Detector to control the layer 1 automaton.This object is only valid for basic rate interfaces. |
| isdnloginAllowEntry | 1.3.6.1.4.1.272.4.2.11.1 | not-accessible | ||
| STR isdnloginAllowRemoteNumber | 1.3.6.1.4.1.272.4.2.11.1.2 | DisplayString | read-write | The number of the ISDN partner that is allowed to login via isdnlogin through the corresponding ISDN Stack. The wildcards '*', '?', '[', ']', '{', '}' may be used. See isdnCallRemoteNumber. |
| OCT isdnloginAllowRemoteSubaddress | 1.3.6.1.4.1.272.4.2.11.1.3 | OCTET STRING | read-write | The subaddress of the remote number. The subaddress is coded in NSAP format as octets. See isdnloginAllowRemoteNumber. |
| INT isdnloginAllowScreening | 1.3.6.1.4.1.272.4.2.11.1.4 | INTEGER | read-write | The screening indicator of the calling party number (CPN). The isdnloginAllowScreening field can be used to gauge the `trustworthiness' of the CPN field (see isdnCallScreening). Indicators are ordered from highest to lowest as follows: indicator: CPN assigned: verification: `network' by network none `user-verified' by user verification successful `user' by user none `user-failed' by user verification failed Set this field to `dont-care' to accept all calls. Set this field to `delete' to delete this entry. Otherwise calls are accepted only if the screening indicator matches or is higher than the set value. |
| INT isdnloginAllowStkNumber | 1.3.6.1.4.1.272.4.2.11.1.1 | INTEGER | read-write | The number of the ISDN stack, that accepts incoming isdnlogin calls. Refer to the isdnStkTable. The value `-1' matches all available stacks. |
| isdnloginAllowTable | 1.3.6.1.4.1.272.4.2.11 | not-accessible | The isdnloginAllowTable contains information about the ISDN partners that are allowed to login to the BRICK via the isdnlogin service. ISDN callers are identified by their calling partner number. Incoming isdnlogin requests can be restricted to single ISDN stacks. If this table is empty all calls given to the isdnlogind, are accepted. (Note that the isdnDispatchTable is consulted first.) Creating entries: Entries are created by assigning a value to the isdnloginAllowStkNumber object. Deleting entries: An entry can be removed by assigning the value `delete' to its isdnloginAllowScreening object. | |
| INT isdnLoginOnPPPDispatch | 1.3.6.1.4.1.272.4.2.9 | INTEGER | read-write | Allows or disallows incoming ISDN calls (with an ISDN service indicator of 'telephony'), to be connected to the isdnlogin daemon even though the call has a matching service in the isdnDispatchTable (isdnDspItem). These calls must be initiated using isdnlogin telephony. |
| INT isdnStkBchannels | 1.3.6.1.4.1.272.4.2.3.1.25 | INTEGER | read-write | Number of B channels that correspond to that stack. |
| INT isdnStkClearAllCalls | 1.3.6.1.4.1.272.4.2.3.1.22 | INTEGER | read-write | Setting this value to clear(2) will force all current connections on this stack to terminate. |
| INT isdnStkConfiguration | 1.3.6.1.4.1.272.4.2.3.1.5 | INTEGER | read-write | |
| STR isdnStkDialOutPrefix | 1.3.6.1.4.1.272.4.2.3.1.26 | DisplayString | read-write | Prefix for PABX dialout. This entry is added to a dialing number provided by the calling site via PPP negotiation (LCP Callback Option / PPP Bandwith Alllocation Protocol). |
| isdnStkEntry | 1.3.6.1.4.1.272.4.2.3.1 | not-accessible | ||
| INT isdnStkIsdnIfIndex | 1.3.6.1.4.1.272.4.2.3.1.3 | INTEGER | read-write | The index of the ISDN interface. The isdnIfTable lists all available ISDN interfaces. |
| INT isdnStkLayer2State | 1.3.6.1.4.1.272.4.2.3.1.24 | INTEGER | read-only | Shows the current state of Layer2. To allow ISDN connections, the state established(4) must be assigned. |
| INT isdnStkNumber | 1.3.6.1.4.1.272.4.2.3.1.1 | INTEGER | read-write | Unique number of an ISDN stack (0..n). This number can be used in the isdnDispatchTable. |
| INT isdnStkProtocolProfile | 1.3.6.1.4.1.272.4.2.3.1.4 | INTEGER | read-write | The protocol for the D channel. Assigning `delete' to this object has the effect of removing the entry from this table. |
| STR isdnStkSPID | 1.3.6.1.4.1.272.4.2.3.1.6 | DisplayString | read-write | The service profile identifier; only required for the national ISDN1 protocol in North America. |
| INT isdnStkStatus | 1.3.6.1.4.1.272.4.2.3.1.23 | INTEGER | read-only | Shows the status of this ISDN stack. If auto configuration was successful for this stack, this object will be loaded(1). If this stack is not loaded, ISDN calls are not possible. |
| isdnStkTable | 1.3.6.1.4.1.272.4.2.3 | not-accessible | The isdnStkTable contains information for each ISDN protocol stack currently configured on the system. Entries are normally created by the system at boot time, during the auto configuration process, but can also be added manually. Creating entries: Entries are created by the system during the ISDN auto configuration procedure at boot time (see Chapter 3). Entries can also be created by assigning a value to the Number and isdnIfNumber objects. Deleting entries: Entries can be removed by assigning the value 'delete' to the ProtocolProfile object. | |
| INT isdnStkTeiProc | 1.3.6.1.4.1.272.4.2.3.1.7 | INTEGER | read-write | The Tei procedure used. Note that for point-to-point configurations this object should be set to fixed(2). |
| INT isdnStkTeiValue | 1.3.6.1.4.1.272.4.2.3.1.8 | INTEGER | read-write | The Tei value. Note that for point-to-point configurations this object should be 0. |
| INT isdnX31AssignedTo | 1.3.6.1.4.1.272.4.2.6.1.5 | INTEGER | read-write | The service this TEI value is assigned to. |
| INT isdnX31IsdnIfIndex | 1.3.6.1.4.1.272.4.2.6.1.1 | INTEGER | read-write | The corresponding ISDN interface that is used for this call. Refer to the isdnIfTable. |
| INT isdnX31TeiProc | 1.3.6.1.4.1.272.4.2.6.1.2 | INTEGER | read-write | The procedure used for polling of TEI (terminal end-point identifiers) values. |
| INT isdnX31TeiValue | 1.3.6.1.4.1.272.4.2.6.1.3 | INTEGER | read-write | The TEI value for this interface. |
| org | 1.3 | |||
| private | 1.3.6.1.4 |
RFC description
Monitors ISDN (BRI and PRI) interfaces on BIANCA/BOX devices, tracking layer 1 state, channel status, and connection statistics.
Start monitoring bintec BIANCA/BRICK ISDN/VPN routers (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.