AtiSwitch-MIB

All MIBs › AtiSwitch-MIB

Organization: Allied Telesyn International

Last Updated: 2002-05-01

Category: VLAN and Bridging, Vendor: Allied Telesis

Description: Manages core switch configuration including port speed, duplex, storm control, and QoS on Allied Telesyn switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AtiSwitch-MIB?

AtiSwitch-MIB manages core Layer 2/3 switch configuration for Allied Telesyn's ("ATI") next-generation switch product line, covering port topology, IP management configuration, and software version, intended for use in both Windows and UNIX-based management environments. Its general data categories are hardware/product inventory (product type, base and uplink port counts, uplink types), software version, and IP/network configuration (management IP address, subnet mask, routing enable, address status). It supports monitoring of both hardware and software status — atiswitchSwVersion tracks the running firmware/software version for compliance and upgrade auditing, atiswitchIPAddressStatus reveals whether the switch's management IP is properly bound, and atiswitchReset is a control object whose value can indicate/trigger a device reboot, relevant to uptime tracking. It appears to be a self-contained vendor MIB focused on the switch's own management/product identity rather than importing other MIBs. It is deployed on Allied Telesyn Layer 2 switches in enterprise wiring-closet and small-to-midsize network environments. Engineers can download the AtiSwitch-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in AtiSwitch-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Allied Telesyn Layer 2/3 next-generation switch

Monitoring Examples

An admin would poll atiswitchSwVersion to audit firmware versions fleet-wide before a security patch rollout, and atiswitchIPAddressStatus to confirm the switch's management IP (atiswitchConfigIpAddress/atiswitchConfigSubMask) is correctly active — a status of "invalid" or "duplicate" would indicate an addressing conflict cutting off management access. atiswitchBasePortCount and atiswitchUplinkPortCount, along with atiswitchUplink1Type/atiswitchUplink2Type, let the operator confirm the switch's physical port inventory matches expectations. atiswitchConfigRouting reveals whether Layer 3 routing is enabled on a unit expected to operate purely as a Layer 2 switch.

What Can Be Monitored

software/firmware version
management IP address status
base and uplink port counts
uplink port type
routing enabled/disabled
reset/reboot control

Imported Objects

From RFC1155-SMI

enterprises

From SNMPv2-SMI

Counter32
Integer32
IpAddress
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using atiswitchEthMonRxGoodFrames OID:

Select an Allied Telesyn Layer 2/3 next-generation switch (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type atiswitchEthMonRxGoodFrames into the Find box to locate it in the OID tree, then select it and click OK. The total number of good frames received on the switch. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
alliedTelesyn	1.3.6.1.4.1.207
at_8012M	1.3.6.1.4.1.207.1.4.86
at_8016F_MT	1.3.6.1.4.1.207.1.4.82
at_8016F_SC	1.3.6.1.4.1.207.1.4.79
at_8024	1.3.6.1.4.1.207.1.4.66
at_8024GB	1.3.6.1.4.1.207.1.4.67
at_8024M	1.3.6.1.4.1.207.1.4.78
at_8026FC	1.3.6.1.4.1.207.1.4.80
at_8026T	1.3.6.1.4.1.207.1.4.89
at_8088_MT	1.3.6.1.4.1.207.1.4.88
at_8088_SC	1.3.6.1.4.1.207.1.4.87
atiProduct	1.3.6.1.4.1.207.1
I32 atiswitchBasePortCount	1.3.6.1.4.1.207.8.15.1.2	Integer32	read-only	This object determines the number of base Ethernet ports in the switch.
atiswitchBasicVlanEntry	1.3.6.1.4.1.207.8.15.4.1.1		not-accessible	An entry describing the configured Virtual LAN.
atiswitchBasicVlanTable	1.3.6.1.4.1.207.8.15.4.1		not-accessible	Table of Virtual LANs configured in the switch.
INT atiswitchBeVlanIndex	1.3.6.1.4.1.207.8.15.4.1.1.1	INTEGER	read-only	Index of the Virtual LAN entry. Maximum number of Virtual LANs in 8024/8024GB is 32.
INT atiswitchBeVlanMirrorPort	1.3.6.1.4.1.207.8.15.4.1.1.6	INTEGER	read-create	Port number on which all Virtual LAN traffic is mirrored on. By default the value is 0 indicating no port mirroring.
STR atiswitchBeVlanName	1.3.6.1.4.1.207.8.15.4.1.1.2	DisplayString	read-create	Name of the Virtual LAN.
ROW atiswitchBeVlanRowStatus	1.3.6.1.4.1.207.8.15.4.1.1.7	RowStatus	read-create	Indicates the status of this entry. This object is used to create, modify or delete Virtual LAN entries as per the RowStatus specification of SMIv2. There are two ways to create a Virtual LAN entry - CreateAndGo (Used when all objects of the entry are set at one go) and CreateAndWait (Used when individual objects are set independently). CreateAndGo method: Assign values to all objects of the Virtual LAN entry. Set this object to CreateAndGo(4). CreateAndWait method: Set this object to CreateAndWait(5). Set individual object entries. When all other entries are set, set this object to Active(1). To delete a Virtual LAN entry, set this object to destroy(6).
STR atiswitchBeVlanTaggedPortMask	1.3.6.1.4.1.207.8.15.4.1.1.4	DisplayString	read-create	List of tagged ports in the Virtual LAN.
INT atiswitchBeVlanTagId	1.3.6.1.4.1.207.8.15.4.1.1.3	INTEGER	read-create	VId of the Virtual LAN as stored in the tag information header in accordance with 802.1q specification.
STR atiswitchBeVlanUntaggedPortMask	1.3.6.1.4.1.207.8.15.4.1.1.5	DisplayString	read-create	List of untagged ports in the Virtual LAN.
atiswitchConfigGroup	1.3.6.1.4.1.207.8.15.2
IP atiswitchConfigIpAddress	1.3.6.1.4.1.207.8.15.1.8.1	IpAddress	read-write	IP address of the switch.
IP atiswitchConfigRouting	1.3.6.1.4.1.207.8.15.1.8.3	IpAddress	read-write	Gateway address for the switch.
IP atiswitchConfigSubMask	1.3.6.1.4.1.207.8.15.1.8.2	IpAddress	read-write	Subnet mask of the switch.
STR atiswitchDefaultDomainName	1.3.6.1.4.1.207.8.15.1.8.6	DisplayString	read-write	This attribute specifies the default Domain Name for the switch.
IP atiswitchDNServer	1.3.6.1.4.1.207.8.15.1.8.5	IpAddress	read-write	This attribute specifies the DNS server address for the switch.
atiswitchEthernetStatsGroup	1.3.6.1.4.1.207.8.15.5
C32 atiswitchEthErrorAlignment	1.3.6.1.4.1.207.8.15.5.2.2	Counter32	read-only	The total number of packets received that has alignment errors.
C32 atiswitchEthErrorCRC	1.3.6.1.4.1.207.8.15.5.2.1	Counter32	read-only	The total number of CRC errors on received packets.
C32 atiswitchEthErrorLateCollision	1.3.6.1.4.1.207.8.15.5.2.4	Counter32	read-only	The number of times collision was detected in the switch.
C32 atiswitchEthErrorRxBadFrames	1.3.6.1.4.1.207.8.15.5.2.3	Counter32	read-only	The total number of bad frames received.
atiswitchEthErrorStats	1.3.6.1.4.1.207.8.15.5.2
C32 atiswitchEthErrorTxTotal	1.3.6.1.4.1.207.8.15.5.2.5	Counter32	read-only	Total number of errors resulting from transmit operations.
C32 atiswitchEthMonRxGoodFramesEx	1.3.6.1.4.1.207.8.15.5.1.1	Counter32	read-only	The total number of good frames received on the switch.
C32 atiswitchEthMonRxOverruns	1.3.6.1.4.1.207.8.15.5.1.8	Counter32	read-only	The total number of Received Overrun Frames while switching.
atiswitchEthMonStats	1.3.6.1.4.1.207.8.15.5.1
C32 atiswitchEthMonTxBroadcastFrames	1.3.6.1.4.1.207.8.15.5.1.6	Counter32	read-only	The total number of Transmit Broadcast Frames while switching.
C32 atiswitchEthMonTxCollisions	1.3.6.1.4.1.207.8.15.5.1.5	Counter32	read-only	The total number of collisions detected while transmitting from the switch.
C32 atiswitchEthMonTxDeferred	1.3.6.1.4.1.207.8.15.5.1.4	Counter32	read-only	The number of times a transmission attempt failed because of the medium being busy.
C32 atiswitchEthMonTxGoodFrames	1.3.6.1.4.1.207.8.15.5.1.2	Counter32	read-only	The total number of good frames that has been transimitted by the switch.
C32 atiswitchEthMonTxMulticastFrames	1.3.6.1.4.1.207.8.15.5.1.7	Counter32	read-only	The total number of Transmit Multicast frames while switching.
C32 atiswitchEthMonTxTotalBytes	1.3.6.1.4.1.207.8.15.5.1.3	Counter32	read-only	The total number of bytes transimitted from the switch.
atiswitchEthPortError	1.3.6.1.4.1.207.8.15.6.2
atiswitchEthPortErrorEntry	1.3.6.1.4.1.207.8.15.6.2.1.1		not-accessible	A collection of statistics kept for a particular port.
INT atiswitchEthPortErrorId	1.3.6.1.4.1.207.8.15.6.2.1.1.1	INTEGER	read-only	Port number.
C32 atiswitchEthPortErrorRxBadFrames	1.3.6.1.4.1.207.8.15.6.2.1.1.2	Counter32	read-only	Total number of bad Frames received on this port.
atiswitchEthPortErrorTable	1.3.6.1.4.1.207.8.15.6.2.1		not-accessible	A list of statistics entries.
C32 atiswitchEthPortErrorTxTotal	1.3.6.1.4.1.207.8.15.6.2.1.1.3	Counter32	read-only	Total number of errors resulting from transmit operations.
atiswitchEthPortMonEntry	1.3.6.1.4.1.207.8.15.6.1.1.1		not-accessible	A colletion of statistics kept for a particular port.
INT atiswitchEthPortMonId	1.3.6.1.4.1.207.8.15.6.1.1.1.1	INTEGER	read-only	Port number.
C32 atiswitchEthPortMonRxGoodFrames	1.3.6.1.4.1.207.8.15.6.1.1.1.2	Counter32	read-only	The total number of good frames received on this port.
C32 atiswitchEthPortMonRxOverruns	1.3.6.1.4.1.207.8.15.6.1.1.1.9	Counter32	read-only	The total number of over sized frames received on this port.
atiswitchEthPortMonStats	1.3.6.1.4.1.207.8.15.6.1
atiswitchEthPortMonTable	1.3.6.1.4.1.207.8.15.6.1.1		not-accessible	A list of statistics entry for each port.
C32 atiswitchEthPortMonTxBroadcastFrames	1.3.6.1.4.1.207.8.15.6.1.1.1.7	Counter32	read-only	The total number of broadcast frames transmitted from this port.
C32 atiswitchEthPortMonTxCollisions	1.3.6.1.4.1.207.8.15.6.1.1.1.6	Counter32	read-only	The total number of collisions while switching on an interface.
C32 atiswitchEthPortMonTxDeferred	1.3.6.1.4.1.207.8.15.6.1.1.1.5	Counter32	read-only	This is the count of first time Transmission attempt which failed on an interface due to medium being busy.
C32 atiswitchEthPortMonTxGoodFrames	1.3.6.1.4.1.207.8.15.6.1.1.1.3	Counter32	read-only	The total number of good frames transmitted from this port.
C32 atiswitchEthPortMonTxMulticastFrames	1.3.6.1.4.1.207.8.15.6.1.1.1.8	Counter32	read-only	The total number of multicast frames transmitted from this port.
C32 atiswitchEthPortMonTxTotalBytes	1.3.6.1.4.1.207.8.15.6.1.1.1.4	Counter32	read-only	The total number of bytes transmitted from this port.
atiswitchEthPortStatsGroup	1.3.6.1.4.1.207.8.15.6
NTF atiswitchFanStopTrap	1.3.6.1.4.1.207.8.15.9.1			Trap sent when an error in the fan operation is detected.
I32 atiswitchFwdVlanAge	1.3.6.1.4.1.207.8.15.7.1.1.3	Integer32	read-only	Current age of the MAC Address in the forwarding table - 0 indicates it is still active, 1 indicates that the address has aged out.
atiswitchFwdVlanEntry	1.3.6.1.4.1.207.8.15.7.1.1		not-accessible	Entry in the atiswitchFwdVlanTable.
atiswitchFwdVlanGroup	1.3.6.1.4.1.207.8.15.7
MAC atiswitchFwdVlanMACAddr	1.3.6.1.4.1.207.8.15.7.1.1.1	MACAddress	read-only	A MAC address from the forwarding table of the switch.
I32 atiswitchFwdVlanPort	1.3.6.1.4.1.207.8.15.7.1.1.5	Integer32	read-only	Either the value 0, or the port number of the port on which a frame having a source address equal to the atiswitchFwdVlanMACAddr has been seen. A value of 0 indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address.
INT atiswitchFwdVlanStatus	1.3.6.1.4.1.207.8.15.7.1.1.4	INTEGER	read-only	Status of the MAC address - inactive (1): It is no longer valid e.g, it was learned and has since aged out, but has not yet been flushed from the table, active (2): Learned or statically assigned and currently in use and other (3): Neither of the other two.
atiswitchFwdVlanTable	1.3.6.1.4.1.207.8.15.7.1		not-accessible	This table associates MAC addresses (as stored in the forwarding table of the switch) to the Virtual LAN to which it belongs.
I32 atiswitchFwdVlanVlanId	1.3.6.1.4.1.207.8.15.7.1.1.2	Integer32	read-only	The Virtual LAN to which atiswitchFwdVlanMACAddr belongs to.
INT atiswitchIPAddressStatus	1.3.6.1.4.1.207.8.15.1.8.4	INTEGER	read-only	The IP Address can be obtained/configured through different ways - through DHCP, through Bootp or through a static configuration. This object specifies how the IP address, subnet mask and the gateway address currently used by the switch was configured/obtained.
atiswitchIpGroup	1.3.6.1.4.1.207.8.15.1.8
atiSwitchMib	1.3.6.1.4.1.207.8.15			Private MIB for ATI next generation layer 2 switches. This MIB can be used in Windows and UNIX environment
I32 atiswitchMirroringDestinationPort	1.3.6.1.4.1.207.8.15.2.3	Integer32	read-write	This attribute identifies the destination port number which mirrors the source port. All packets received, transmitted or both on the source port gets mirrored on to this port. This attribute will have the value 0 when port mirroring is disabled.
STR atiswitchMirroringSourcePorts	1.3.6.1.4.1.207.8.15.2.2	DisplayString	read-write	This attribute identifies the source ports which are mirrored. All packets received, transmitted or both on these ports gets mirrored on to the destination port. It's value can be a single port number or a contiguous range of ports (eg. 1-5). This attribute will have an empty string when port mirroring is disabled.
INT atiswitchMirrorState	1.3.6.1.4.1.207.8.15.2.1	INTEGER	read-write	If the attribute is set to one of the first three values, then port mirroring is enabled. If disabled, port operation works nomally. No traffic gets mirrored.
atiswitchNMGroup	1.3.6.1.4.1.207.8.15.1.9
atiswitchNwMgrEntry	1.3.6.1.4.1.207.8.15.1.9.1.1		not-accessible	An entry of atiswitchNwMgrTable specifying each management station to which a SNMP trap is sent.
INT atiswitchNwMgrIndex	1.3.6.1.4.1.207.8.15.1.9.1.1.1	INTEGER	read-only	The index for the management station entry.
IP atiswitchNwMgrIpAddr	1.3.6.1.4.1.207.8.15.1.9.1.1.2	IpAddress	read-write	The IP address of the management station.
atiswitchNwMgrTable	1.3.6.1.4.1.207.8.15.1.9.1		not-accessible	This table contains the list of IP Addresses (management stations) to which SNMP Traps are sent. The maximum number of entries in the table is 4.
atiswitchPort2VlanEntry	1.3.6.1.4.1.207.8.15.4.2.1		not-accessible	An entry in the table, containing per port Virtual LAN information.
atiswitchPort2VlanTable	1.3.6.1.4.1.207.8.15.4.2		not-accessible	Table of per port Virtual LAN configuration.
INT atiswitchPortAutosenseOrHalfDuplex	1.3.6.1.4.1.207.8.15.3.1.1.3	INTEGER	read-write	This object allows an admin request to configure whether this port is set to autosense or one of the different speed/duplex combinations.
INT atiswitchPortBackPressureConfig	1.3.6.1.4.1.207.8.15.3.1.1.9	INTEGER	read-write	This per-port attribute describes whether the port identified has Back Pressure Enabled or not.By default, Back Pressure is Disabled.
INT atiswitchPortBroadcastConfig	1.3.6.1.4.1.207.8.15.3.1.1.12	INTEGER	read-write	This per-port attribute determines if broadcast packets received should be discarded or processed. By default, they will be processed.
INT atiswitchPortCOSPriorityConfig	1.3.6.1.4.1.207.8.15.3.1.1.11	INTEGER	read-write	This per-port attribute allows the configuration of the priority of the port. There are 8 priorities as per the IEEE standard with 0 being the lowest priority and 7 the highest. In a switch environment, ports with higher priority has it's to and from traffic given higher priority when compared with those with lower priority.
INT atiswitchPortDuplexStatus	1.3.6.1.4.1.207.8.15.3.1.1.5	INTEGER	read-only	This object allows an admin request to read the status of Duplex on this port.
atiswitchPortEntry	1.3.6.1.4.1.207.8.15.3.1.1		not-accessible	The device type in the DeviceTable.
INT atiswitchPortFlowControlConfig	1.3.6.1.4.1.207.8.15.3.1.1.8	INTEGER	read-write	This per port attribute determines whether the port has flow control enabled or not. By default, flow control is disabled.
atiswitchPortGroup	1.3.6.1.4.1.207.8.15.3
INT atiswitchPortLinkState	1.3.6.1.4.1.207.8.15.3.1.1.4	INTEGER	read-only	This attribute allows an admin request to read the status of link state on this port.
STR atiswitchPortName	1.3.6.1.4.1.207.8.15.3.1.1.2	DisplayString	read-write	This attribute associates a user defined string name with the port.
INT atiswitchPortNumber	1.3.6.1.4.1.207.8.15.3.1.1.1	INTEGER	read-only	The object identifies the port of the switch.
INT atiswitchPortReset	1.3.6.1.4.1.207.8.15.3.1.1.13	INTEGER	read-write	This per-port attribute resets the port to the original default configuration.This can prove useful in situations where a port is experiencing a problem making a valid connection to the end node. Setting the value to 'no-reset' has no effect.
INT atiswitchPortSpeed	1.3.6.1.4.1.207.8.15.3.1.1.6	INTEGER	read-only	This attribute allows an admin request to read the speed of this port.
INT atiswitchPortState	1.3.6.1.4.1.207.8.15.3.1.1.7	INTEGER	read-write	This attribute allows an admin request to disable or enable communications on this port. It also responds with the status of the port. Except enabled(1) and disabled(2), all values are read-only status.
atiswitchPortTable	1.3.6.1.4.1.207.8.15.3.1		not-accessible	This table contains all the type of devices supported by this MIB.
INT atiswitchPortVlanTagPriorityConfig	1.3.6.1.4.1.207.8.15.3.1.1.10	INTEGER	read-write	This per-port attribute allows the configuration of the Tag Priority to be Override or use the Tag Priority. By Default, all ports use Vlan Tag priority.
INT atiswitchProductType	1.3.6.1.4.1.207.8.15.1.1	INTEGER	read-only	This object identifies the Product Type.
INT atiswitchPvPortNumber	1.3.6.1.4.1.207.8.15.4.2.1.1	INTEGER	read-only	This object identifies the port on the switch.
STR atiswitchPvVlanName	1.3.6.1.4.1.207.8.15.4.2.1.2	DisplayString	read-only	This object identifies the Virtual LAN name to which the port belongs to.
INT atiswitchReset	1.3.6.1.4.1.207.8.15.1.4	INTEGER	read-write	Setting this object to switchreset will cause the switch to perform a soft reboot. Setting this object to switch_no_reset will have no effect.
INT atiswitchSecurityAction	1.3.6.1.4.1.207.8.15.2.5	INTEGER	read-write	This attribute identifies the security action taken in case of an intruder detected.
INT atiswitchSecurityConfig	1.3.6.1.4.1.207.8.15.2.4	INTEGER	read-write	This attribute is a port security configuration object. Setting the value to 'disabled' will allow the switch to learn new MAC addresses as they come in. In enabledLearningLocked mode, the device will stop learning new addresses and the old addresses that the device has learned will be locked. In enabledLimited mode, only a limited number of addresses will be learned. In enabledSecured mode, the administrator is responsible for entering the MAC addresses manually. By doing this, the administrator knows exactly who is connecting to the switch.
MAC atiswitchStaticMACAddress	1.3.6.1.4.1.207.8.15.8.1.1.1	MACAddress	read-write	This object identifies the MAC address associated with Static MAC table.
atiswitchStaticMACEntry	1.3.6.1.4.1.207.8.15.8.1.1		not-accessible	Entry in the atiswitchStaticMACTable.
INT atiswitchStaticMACEntryStatus	1.3.6.1.4.1.207.8.15.8.1.1.3	INTEGER	read-write	The status of this entry. The meanings of the values are: valid(1) : This entry is valid. invalid(2) : This entry is no longer valid, but has not yet been flushed from the table.
atiswitchStaticMACGroup	1.3.6.1.4.1.207.8.15.8
INT atiswitchStaticMACPortNumber	1.3.6.1.4.1.207.8.15.8.1.1.2	INTEGER	read-write	This object identifies the port for which the MAC address is associated statically in the MAC Table.
atiswitchStaticMACTable	1.3.6.1.4.1.207.8.15.8.1		not-accessible	This tables lists MAC addresses lexicographically from the static table which binds MAC address to ports on the switch.
STR atiswitchSw	1.3.6.1.4.1.207.8.15.1.7.1	DisplayString	read-only	Identifies the name of the software running in the switch.
atiswitchSwGroup	1.3.6.1.4.1.207.8.15.1.7
STR atiswitchSwVersion	1.3.6.1.4.1.207.8.15.1.7.2	DisplayString	read-only	Identifies the version number of the software running in the switch.
atiswitchSysGroup	1.3.6.1.4.1.207.8.15.1
NTF atiswitchTemperatureAbnormalTrap	1.3.6.1.4.1.207.8.15.9.2			Trap sent when the temperature of the switch is abnormal.
atiswitchTraps	1.3.6.1.4.1.207.8.15.9
INT atiswitchUplink1Type	1.3.6.1.4.1.207.8.15.1.5	INTEGER	read-only	This object returns the MDA (Media Dependant Adapter) type of Uplink port 1. If there is no uplink installed it will return a value of none.
INT atiswitchUplink2Type	1.3.6.1.4.1.207.8.15.1.6	INTEGER	read-only	This object returns the MDA (Media Dependant Adapter) type of Uplink port 2. If there is no uplink installed it will return a value of none.
I32 atiswitchUplinkPortCount	1.3.6.1.4.1.207.8.15.1.3	Integer32	read-only	This object determines the total number of uplink ports available in the switch.
atiswitchVlanConfigGroup	1.3.6.1.4.1.207.8.15.4
INT atiswitchVlanMode	1.3.6.1.4.1.207.8.15.4.3	INTEGER	read-write	This object specifies the current VLAN mode. Setting this object to 'user-configured (1)' allows the manager to create, delete and modify VLANs using 'atiswitchBasicVlanTable'. Setting this object to 'multiple (2)' or 'multiple-802-1Q (3)'will result in the creation of predefined VLANs. Setting these values requires that the object 'atiswitchVlanUplinkVlanPort' also be set in the same SET request. Note that SET operations on any object under 'atiswitchBasicVlanTable' are not allowed in these two modes.
I32 atiswitchVlanUplinkVlanPort	1.3.6.1.4.1.207.8.15.4.4	Integer32	read-write	This object specifies the Uplink VLAN Port ID used while creating pre-configured VLANs. This object can be set to any valid Port ID present on the switch. Note that a SET operation on the object 'atiswitchVlanMode' to the value 'multiple (2)' or 'multiple-802-1Q (3)' should always be accompanied by a SET operation on this object in the same SET request. By default this object is set to 0 when 'atiswitchVlanMode' is set to 'user-configured (1)'.
mibObject	1.3.6.1.4.1.207.8
swhub	1.3.6.1.4.1.207.1.4

RFC description

Allied Telesyn MIB for managing ATI next-generation layer 2 switches, providing SNMP object definitions for system configuration, port settings, and network management on Allied Telesyn switching equipment.

Start monitoring Allied Telesyn Layer 2/3 next-generation switches (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AtiSwitch-MIB