ESN310-MIB

All MIBs › ESN310-MIB

Organization: Ericsson AB

Last Updated: 2003--0-3-

Category: Vendor: Allied Telesis, Vendor: ERI, Vendor: Enterasys/Cabletron

Description: Manages hardware, port, and network configuration for ESN310 series network equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ESN310-MIB?

ESN310-MIB is a vendor-specific MIB for ESN310-series managed network switches, sharing the same switch-info object pattern (hardware/firmware version fields, power status, unit role) seen in other Accton-derived OEM switch MIBs, alongside VLAN-based management access configuration. It exposes hardware and firmware version information, power-supply status, unit stacking role, and a management VLAN setting used to control administrative access to the device. This makes it a hardware/software status MIB for basic switch health: version/firmware tracking, power health, and stack role are all directly monitorable. No dependency on other standard MIBs is evident beyond generic SNMP SMI conventions. It is deployed for inventory and basic health monitoring of ESN310-series switches in small/medium enterprise networks. Engineers can download the ESN310-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ESN310-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ESN310-series managed Ethernet switch

Monitoring Examples

switchInfoTable/switchInfoEntry, indexed by swUnitIndex, expose swHardwareVer, swMicrocodeVer, swBootRomVer, swLoaderVer, swOpCodeVer, and swPowerStatus, while switchManagementVlan defines which VLAN carries SNMP/management traffic. An operator polls swPowerStatus to catch a power-supply fault and checks swOpCodeVer/swMicrocodeVer before scheduling a firmware upgrade across the unit.

What Can Be Monitored

hardware/firmware/bootrom/loader version
power supply status
unit role in stack
management VLAN configuration
port count per unit

Imported Objects

From BRIDGE-MIB

BridgeId
Timeout
dot1dStpPort
dot1dStpPortEntry

From DXD-SMI

diaxMIB

MODULE-IDENTITY

From IF-MIB

InterfaceIndex

From P-BRIDGE-MIB

EnabledStatus

From Q-BRIDGE-MIB

PortList

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using xstInstancePortForwardTransitions OID:

Select an ESN310-series managed Ethernet switch (Accton-derived OEM) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type xstInstancePortForwardTransitions into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of times this port has transitioned from the Learning state to the Forwarding state. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
esn310MIB	1.3.6.1.4.1.193.72.900			The MIB module for esn310.
esn310MIBObjects	1.3.6.1.4.1.193.72.900.1
switchMgt	1.3.6.1.4.1.193.72.900.1.1
INT switchManagementVlan	1.3.6.1.4.1.193.72.900.1.1.1	INTEGER	read-write	The VLAN on which management is done.
I32 switchNumber	1.3.6.1.4.1.193.72.900.1.1.2	Integer32	read-only	The total number of switches present on this system.
switchInfoTable	1.3.6.1.4.1.193.72.900.1.1.3		not-accessible	Table of descriptive and status information about switches in this system.
switchInfoEntry	1.3.6.1.4.1.193.72.900.1.1.3.1		not-accessible	An entry in the table, containing information about a single switch in this system.
I32 swUnitIndex	1.3.6.1.4.1.193.72.900.1.1.3.1.1	Integer32	not-accessible	This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.
STR swHardwareVer	1.3.6.1.4.1.193.72.900.1.1.3.1.2	DisplayString	read-only	Hardware version of the main board.
STR swMicrocodeVer	1.3.6.1.4.1.193.72.900.1.1.3.1.3	DisplayString	read-only	Microcode version of the main board.
STR swLoaderVer	1.3.6.1.4.1.193.72.900.1.1.3.1.4	DisplayString	read-only	Loader version of the main board.
STR swBootRomVer	1.3.6.1.4.1.193.72.900.1.1.3.1.5	DisplayString	read-only	Boot ROM code version of the main board.
STR swOpCodeVer	1.3.6.1.4.1.193.72.900.1.1.3.1.6	DisplayString	read-only	Operation code version of the main board.
I32 swPortNumber	1.3.6.1.4.1.193.72.900.1.1.3.1.7	Integer32	read-only	The total port number of this switch (including expansion slot).
INT swPowerStatus	1.3.6.1.4.1.193.72.900.1.1.3.1.8	INTEGER	read-only	Indicates the switch using internalPower(1), redundantPower(2) or both(3)
INT swRoleInSystem	1.3.6.1.4.1.193.72.900.1.1.3.1.9	INTEGER	read-only	Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.
STR swSerialNumber	1.3.6.1.4.1.193.72.900.1.1.3.1.10	DisplayString	read-only	Serial number of the switch.
INT swExpansionSlot1	1.3.6.1.4.1.193.72.900.1.1.3.1.11	INTEGER	read-only	Type of expansion module in this switch slot 1.
INT swExpansionSlot2	1.3.6.1.4.1.193.72.900.1.1.3.1.12	INTEGER	read-only	Type of expansion module in this switch slot 2.
STR swServiceTag	1.3.6.1.4.1.193.72.900.1.1.3.1.13	DisplayString	read-only	Service tag serial-number of the switch.
INT switchOperState	1.3.6.1.4.1.193.72.900.1.1.4	INTEGER	read-only	Global operation state of the switch.
switchProductId	1.3.6.1.4.1.193.72.900.1.1.5
STR swProdName	1.3.6.1.4.1.193.72.900.1.1.5.1	DisplayString	read-only
STR swProdManufacturer	1.3.6.1.4.1.193.72.900.1.1.5.2	DisplayString	read-only
STR swProdDescription	1.3.6.1.4.1.193.72.900.1.1.5.3	DisplayString	read-only
STR swProdVersion	1.3.6.1.4.1.193.72.900.1.1.5.4	DisplayString	read-only
STR swProdUrl	1.3.6.1.4.1.193.72.900.1.1.5.5	DisplayString	read-only
INT swIdentifier	1.3.6.1.4.1.193.72.900.1.1.5.6	INTEGER	read-only	A unique identifier of which switch in the chassis is currently being looked at.
STR swChassisServiceTag	1.3.6.1.4.1.193.72.900.1.1.5.7	DisplayString	read-only	The service tag of the chassis this switch resides in.
switchIndivPowerTable	1.3.6.1.4.1.193.72.900.1.1.6		not-accessible	Table about statuses of individual powers.
switchIndivPowerEntry	1.3.6.1.4.1.193.72.900.1.1.6.1		not-accessible	Table about statuses of individual powers.
I32 swIndivPowerUnitIndex	1.3.6.1.4.1.193.72.900.1.1.6.1.1	Integer32	read-only	This is defined as swUnitIndex.
INT swIndivPowerIndex	1.3.6.1.4.1.193.72.900.1.1.6.1.2	INTEGER	read-only	1 means internal power. 2 means external power.
INT swIndivPowerStatus	1.3.6.1.4.1.193.72.900.1.1.6.1.3	INTEGER	read-only	notPresent(1) means not present. green(2) means up. red(3) means down.
portMgt	1.3.6.1.4.1.193.72.900.1.2
portTable	1.3.6.1.4.1.193.72.900.1.2.1		not-accessible	Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains information about each trunk (similar to Cisco's EtherChannel).
portEntry	1.3.6.1.4.1.193.72.900.1.2.1.1		not-accessible	An entry in the table, containing information about configuration in one switch port of the switch.
I32 portIndex	1.3.6.1.4.1.193.72.900.1.2.1.1.1	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
STR portName	1.3.6.1.4.1.193.72.900.1.2.1.1.2	DisplayString	read-write	Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later).
INT portType	1.3.6.1.4.1.193.72.900.1.2.1.1.3	INTEGER	read-only	Indicates the port type.
INT portSpeedDpxCfg	1.3.6.1.4.1.193.72.900.1.2.1.1.4	INTEGER	read-write	Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode hundredBaseTX port can be set as halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as halfDuplex100(4) fullDuplex100(5) thousandBaseSX port can be set as halfDuplex1000(6) fullDuplex1000(7) The actual operating speed and duplex of the port is given by portSpeedDpxStatus.
INT portFlowCtrlCfg	1.3.6.1.4.1.193.72.900.1.2.1.1.5	INTEGER	read-write	(1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (3) Flow control mechanism is backPressure. when the port is in fullDuplex mode.This flow control mechanism will not function. (4) Flow control mechanism is IEEE 802.3x flow control. when the port is in halfDuplex mode.This flow control mechanism will not function. hundredBaseTX and thousandBaseSX port can be set as: enabled(1), disabled(2), backPressure(3), dot3xFlowControl(4). hundredBaseFX port can be set as: enabled(1), disabled(2), backPressure(3). The actual flow control mechanism is used given by portFlowCtrlStatus.
BIT portCapabilities	1.3.6.1.4.1.193.72.900.1.2.1.1.6	Bits	read-write	Port capabilities.
INT portAutonegotiation	1.3.6.1.4.1.193.72.900.1.2.1.1.7	INTEGER	read-write	Whether autonegotiation is enabled.
INT portSpeedDpxStatus	1.3.6.1.4.1.193.72.900.1.2.1.1.8	INTEGER	read-only	The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk and the result is inconsistent among its member ports, this value is error(1).
INT portFlowCtrlStatus	1.3.6.1.4.1.193.72.900.1.2.1.1.9	INTEGER	read-only	(2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trunk and the result is inconsistent among its member ports, this value is error(1).
I32 portTrunkIndex	1.3.6.1.4.1.193.72.900.1.2.1.1.10	Integer32	read-only	The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to trunk at trunkIndex, defined by the corresponding trunkPorts.
trunkMgt	1.3.6.1.4.1.193.72.900.1.3
INT trunkMaxId	1.3.6.1.4.1.193.72.900.1.3.1	INTEGER	read-only	The maximum number for a trunk identifier.
INT trunkValidNumber	1.3.6.1.4.1.193.72.900.1.3.2	INTEGER	read-only	The number of valid trunks.
trunkTable	1.3.6.1.4.1.193.72.900.1.3.3		not-accessible	Table of descriptive and status information about configuration of each trunk, similar to Cisco EtherChannel.
trunkEntry	1.3.6.1.4.1.193.72.900.1.3.3.1		not-accessible	An entry in the table, containing information about configuration in one trunk of the switch.
I32 trunkIndex	1.3.6.1.4.1.193.72.900.1.3.3.1.1	Integer32	not-accessible	This object identifies the trunk within the switch for which this entry contains information.
POR trunkPorts	1.3.6.1.4.1.193.72.900.1.3.3.1.2	PortList	read-create	The complete set of ports currently associated with this trunk.
INT trunkCreation	1.3.6.1.4.1.193.72.900.1.3.3.1.3	INTEGER	read-only	A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.
INT trunkStatus	1.3.6.1.4.1.193.72.900.1.3.3.1.4	INTEGER	read-create	Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry.
lacpMgt	1.3.6.1.4.1.193.72.900.1.4
lacpPortTable	1.3.6.1.4.1.193.72.900.1.4.1		not-accessible	Table for LACP port configuration.
lacpPortEntry	1.3.6.1.4.1.193.72.900.1.4.1.1		not-accessible	Entry for LACP port configuration.
I32 lacpPortIndex	1.3.6.1.4.1.193.72.900.1.4.1.1.1	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
INT lacpPortStatus	1.3.6.1.4.1.193.72.900.1.4.1.1.2	INTEGER	read-write	Whether 802.3ad LACP is enabled.
staMgt	1.3.6.1.4.1.193.72.900.1.5
ENA staSystemStatus	1.3.6.1.4.1.193.72.900.1.5.1	EnabledStatus	read-write	Global spanning tree status: (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.
staPortTable	1.3.6.1.4.1.193.72.900.1.5.2		not-accessible	The table manages port settings for Spanning Tree Protocol 802.1d, or 802.1w depending on the value specified by staProtocolType.
staPortEntry	1.3.6.1.4.1.193.72.900.1.5.2.1		not-accessible	The conceptual entry of staPortTable.
ENA staPortFastForward	1.3.6.1.4.1.193.72.900.1.5.2.1.2	EnabledStatus	read-write	Whether fast forwarding is enabled.
T/F staPortProtocolMigration	1.3.6.1.4.1.193.72.900.1.5.2.1.3	TruthValue	read-write	When operating in RSTP (version 2) mode, setting this object to TRUE(1) object forces the port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.
T/F staPortAdminEdgePort	1.3.6.1.4.1.193.72.900.1.5.2.1.4	TruthValue	read-write	The administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed to be an edge-port and a value of FALSE(2) indicates that this port should be assumed to be a non-edge-port.
T/F staPortOperEdgePort	1.3.6.1.4.1.193.72.900.1.5.2.1.5	TruthValue	read-only	The operational value of the Edge Port parameter. The object is initialized to the value of staPortAdminEdgePort and is set FALSE when a BPDU is received.
INT staPortAdminPointToPoint	1.3.6.1.4.1.193.72.900.1.5.2.1.6	INTEGER	read-write	The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members can be aggregated, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by explicit configuration.
T/F staPortOperPointToPoint	1.3.6.1.4.1.193.72.900.1.5.2.1.7	TruthValue	read-only	The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by explicit configuration or by auto-detection, as described in the staPortAdminPointToPoint object.
I32 staPortLongPathCost	1.3.6.1.4.1.193.72.900.1.5.2.1.8	Integer32	read-write	The contribution of this port to the path cost (as a 32 bit value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost as a 32 bit value when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this MIB object is not instantiated.
INT staProtocolType	1.3.6.1.4.1.193.72.900.1.5.3	INTEGER	read-write	The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'rstp(2)' indicates the Rapid Spanning Tree Protocol is as specified in IEEE 802.1w New values may be defined in the future as new or updated versions of the protocol become available.
I32 staTxHoldCount	1.3.6.1.4.1.193.72.900.1.5.4	Integer32	read-write	The minimum interval between the transmission of consecutive RSTP/MSTP BPDUs in seconds.
INT staPathCostMethod	1.3.6.1.4.1.193.72.900.1.5.5	INTEGER	read-write	Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the Spanning tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the staPortLongPathCost MIB object must be used to retrieve/ configure the spanning tree port path cost as a 32 bit value. The set operation on dot1dStpPortPathCost in the BRIDGE-MIB will be rejected. When retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of staPortLongPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in the BRIDGE-MIB must be used.
xstMgt	1.3.6.1.4.1.193.72.900.1.5.6
xstInstanceCfgTable	1.3.6.1.4.1.193.72.900.1.5.6.4		not-accessible	This table is used to configure Rapid Spanning Tree. Only the first row of the table is used by RST. In the future this table may be used to support other spanning tree protocols.
xstInstanceCfgEntry	1.3.6.1.4.1.193.72.900.1.5.6.4.1		not-accessible	A conceptual row containing the properties of the RST instance.
I32 xstInstanceCfgIndex	1.3.6.1.4.1.193.72.900.1.5.6.4.1.1	Integer32	not-accessible	The index for an entry in the xstInstanceCfgTable table. For RST only the first row in the table is used.
I32 xstInstanceCfgPriority	1.3.6.1.4.1.193.72.900.1.5.6.4.1.2	Integer32	read-write	The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.
I32 xstInstanceCfgTimeSinceTopologyChange	1.3.6.1.4.1.193.72.900.1.5.6.4.1.3	Integer32	read-only	The time (in hundredths of second) since the last topology change detected by the bridge entity in RST.
I32 xstInstanceCfgTopChanges	1.3.6.1.4.1.193.72.900.1.5.6.4.1.4	Integer32	read-only	The total number of topology changes detected by this bridge in RST since the management entity was last reset or initialized.
BRI xstInstanceCfgDesignatedRoot	1.3.6.1.4.1.193.72.900.1.5.6.4.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
I32 xstInstanceCfgRootCost	1.3.6.1.4.1.193.72.900.1.5.6.4.1.6	Integer32	read-only	The cost of the path to the root as seen from this bridge of the RST.
I32 xstInstanceCfgRootPort	1.3.6.1.4.1.193.72.900.1.5.6.4.1.7	Integer32	read-only	The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST .
TIM xstInstanceCfgMaxAge	1.3.6.1.4.1.193.72.900.1.5.6.4.1.8	Timeout	read-only	The maximum age of Rapid Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM xstInstanceCfgHelloTime	1.3.6.1.4.1.193.72.900.1.5.6.4.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using in RST.
TIM xstInstanceCfgHoldTime	1.3.6.1.4.1.193.72.900.1.5.6.4.1.10	Timeout	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
TIM xstInstanceCfgForwardDelay	1.3.6.1.4.1.193.72.900.1.5.6.4.1.11	Timeout	read-only	For the RST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. This value is the current value being used by the bridge. xstInstanceCfgBridgeForwardDelay defines the value that this bridge and all others would start using if/when this bridge were to become the root.
TIM xstInstanceCfgBridgeMaxAge	1.3.6.1.4.1.193.72.900.1.5.6.4.1.12	Timeout	read-only	For RST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
TIM xstInstanceCfgBridgeHelloTime	1.3.6.1.4.1.193.72.900.1.5.6.4.1.13	Timeout	read-only	For the RST protocol, the time (in hundredths of second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
TIM xstInstanceCfgBridgeForwardDelay	1.3.6.1.4.1.193.72.900.1.5.6.4.1.14	Timeout	read-only	For the RST protocol, the time (in hundredths of second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second.
I32 xstInstanceCfgTxHoldCount	1.3.6.1.4.1.193.72.900.1.5.6.4.1.15	Integer32	read-only	For the RST protocol, the value used by the Port Transmit state machine to limit the maximum transmission rate.
INT xstInstanceCfgPathCostMethod	1.3.6.1.4.1.193.72.900.1.5.6.4.1.16	INTEGER	read-only	For RST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the xstInstancePortPathCost MIB object must be used in order to retrieve/configure the spanning tree port path cost as a 32 bit value. The set operation on dot1dStpPortPathCost in the BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of xstInstancePortPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in the BRIDGE-MIB must be used.
xstInstancePortTable	1.3.6.1.4.1.193.72.900.1.5.6.5		not-accessible	The extension table for dot1dStpPortEntry to provide additional Spanning Tree information and configuration.
xstInstancePortEntry	1.3.6.1.4.1.193.72.900.1.5.6.5.1		not-accessible	The conceptual row for xstInstancePortTable.
I32 xstInstancePortPriority	1.3.6.1.4.1.193.72.900.1.5.6.5.1.3	Integer32	read-write	Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active link in the Spanning Tree. This makes a port with higher priority less likely to be blocked if the Spanning Tree Algorithm is detecting network loops. Where more than one port is assigned the highest priority, the port with lowest numeric identifier will be enabled.
INT xstInstancePortState	1.3.6.1.4.1.193.72.900.1.5.6.5.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1) Port receives configuration messages, but does not forward packets. learning(2) Port has transmitted configuration messages for an interval set by the Forward Delay parameter without receiving contradictory information. Port address table is cleared, and the port begins learning addresses. forwarding(3) Port forwards packets, and continues learning addresses. For ports which are disabled (see xstInstancePortEnable), this object will have a value of discarding(1).
ENA xstInstancePortEnable	1.3.6.1.4.1.193.72.900.1.5.6.5.1.5	EnabledStatus	read-only	The enabled/disabled status of the port.
I32 xstInstancePortPathCost	1.3.6.1.4.1.193.72.900.1.5.6.5.1.6	Integer32	read-write	The pathcost of the RST in the range 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).
BRI xstInstancePortDesignatedRoot	1.3.6.1.4.1.193.72.900.1.5.6.5.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
I32 xstInstancePortDesignatedCost	1.3.6.1.4.1.193.72.900.1.5.6.5.1.8	Integer32	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
BRI xstInstancePortDesignatedBridge	1.3.6.1.4.1.193.72.900.1.5.6.5.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OCT xstInstancePortDesignatedPort	1.3.6.1.4.1.193.72.900.1.5.6.5.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
C32 xstInstancePortForwardTransitionsEx	1.3.6.1.4.1.193.72.900.1.5.6.5.1.11	Counter32	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT xstInstancePortPortRole	1.3.6.1.4.1.193.72.900.1.5.6.5.1.12	INTEGER	read-only	The role of the port in the RST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port is connecting a LAN through the bridge to the root bridge (i.e., designated port) (4) The port may provide connectivity if other bridges, bridge ports, or LANs fail or are removed. (5) The port provides backup if other bridges, bridge ports, or LANs fail or are removed.
tftpMgt	1.3.6.1.4.1.193.72.900.1.6
INT tftpFileType	1.3.6.1.4.1.193.72.900.1.6.1	INTEGER	read-write	Type of file to transfer.
STR tftpSrcFile	1.3.6.1.4.1.193.72.900.1.6.2	DisplayString	read-write	The source file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
STR tftpDestFile	1.3.6.1.4.1.193.72.900.1.6.3	DisplayString	read-write	The destination file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
IP tftpServer	1.3.6.1.4.1.193.72.900.1.6.4	IpAddress	read-write	The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been specified.
INT tftpAction	1.3.6.1.4.1.193.72.900.1.6.5	INTEGER	read-write	When this object is set to downloadToRAM(2) or downloadToPROM(3), the device will discontinue its normal operation and begin download of the file specified by tftpSrcFile from the server specified by tftpServer to tftpDestFile in the device using the TFTP protocol. If downloadToRAM(2) is specified, the new image is copied to RAM only (the old image remains unaltered in the flash EPROM). If downloadToPROM(3) is specified the new image is written to the flash EPROM memory after its checksum has been verified to be correct. When the download process is completed, the device will warm boot to restart the newly loaded application. When the device is not downloading, this object will have a value of notDownloading(1). downloadToRAM(2) applies only to configuration download. Otherwise 'invalid value' is replied. When this object is set to upload(4), the device will begin upload of the file specified by tftpScrFile in the device to tftpDestFile in the server specified by tftpServer.
INT tftpStatus	1.3.6.1.4.1.193.72.900.1.6.6	INTEGER	read-only	The status of the last transfer procedure, if any. This object will have a value of downloadStatusUnknown(2) if no transfer process has been performed.
restartMgt	1.3.6.1.4.1.193.72.900.1.7
STR restartOpCodeFile	1.3.6.1.4.1.193.72.900.1.7.1	DisplayString	read-write	Name of op-code file for start-up.
STR restartConfigFile	1.3.6.1.4.1.193.72.900.1.7.2	DisplayString	read-write	Name of configuration file for start-up.
INT restartControl	1.3.6.1.4.1.193.72.900.1.7.3	INTEGER	read-write	Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Setting this object to coldBoot(3) causes the device to reinitialize configuration parameters in non-volatile memory to default values and restart the application software. When the device is running normally, this variable has a value of running(1).
mirrorMgt	1.3.6.1.4.1.193.72.900.1.8
mirrorTable	1.3.6.1.4.1.193.72.900.1.8.1		not-accessible	Table of descriptive and status information about switches in this system.
mirrorEntry	1.3.6.1.4.1.193.72.900.1.8.1.1		not-accessible	An entry in the table, containing information about a single switch in this system.
I32 mirrorDestinationPort	1.3.6.1.4.1.193.72.900.1.8.1.1.1	Integer32	not-accessible	Destination port for mirrored packets. This is defined as ifIndex in the IF-MIB.
I32 mirrorSourcePort	1.3.6.1.4.1.193.72.900.1.8.1.1.2	Integer32	not-accessible	Source port for mirrored packets. This is defined as ifIndex in the IF-MIB.
INT mirrorType	1.3.6.1.4.1.193.72.900.1.8.1.1.3	INTEGER	read-create	If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets.
INT mirrorStatus	1.3.6.1.4.1.193.72.900.1.8.1.1.4	INTEGER	read-create	Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry.
igmpSnoopMgt	1.3.6.1.4.1.193.72.900.1.9
INT igmpSnoopStatus	1.3.6.1.4.1.193.72.900.1.9.1	INTEGER	read-write	Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports.
INT igmpSnoopQuerier	1.3.6.1.4.1.193.72.900.1.9.2	INTEGER	read-write	Whether to act as querier.
INT igmpSnoopQueryCount	1.3.6.1.4.1.193.72.900.1.9.3	INTEGER	read-write	Maximum number of queries that have not been heard on the system before the system starts taking action to solicit reports.
INT igmpSnoopQueryInterval	1.3.6.1.4.1.193.72.900.1.9.4	INTEGER	read-write	Query interval.
INT igmpSnoopQueryMaxResponseTime	1.3.6.1.4.1.193.72.900.1.9.5	INTEGER	read-write	Timeout value (seconds) between IGMP reports received on a port for an IP Multicast Address that can pass before the system sends an IGMP Query out the port and removes it from the list.
INT igmpSnoopQueryTimeout	1.3.6.1.4.1.193.72.900.1.9.6	INTEGER	read-write	Query time-out.
INT igmpSnoopVersion	1.3.6.1.4.1.193.72.900.1.9.7	INTEGER	read-write	Version.
igmpSnoopRouterCurrentTable	1.3.6.1.4.1.193.72.900.1.9.8		not-accessible	Table for current router ports.
igmpSnoopRouterCurrentEntry	1.3.6.1.4.1.193.72.900.1.9.8.1		not-accessible	Entry for current router ports.
U32 igmpSnoopRouterCurrentVlanIndex	1.3.6.1.4.1.193.72.900.1.9.8.1.1	Unsigned32	not-accessible	This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB.
POR igmpSnoopRouterCurrentPorts	1.3.6.1.4.1.193.72.900.1.9.8.1.2	PortList	read-only	The set of ports which are current router ports. Within this list, some router ports are static router ports. Please refer to igmpSnoopRouterStaticTable.
POR igmpSnoopRouterCurrentStatus	1.3.6.1.4.1.193.72.900.1.9.8.1.3	PortList	read-only	The set of ports which are static router ports.
igmpSnoopRouterStaticTable	1.3.6.1.4.1.193.72.900.1.9.9		not-accessible	Table for static router ports.
igmpSnoopRouterStaticEntry	1.3.6.1.4.1.193.72.900.1.9.9.1		not-accessible	Entry for static router ports.
U32 igmpSnoopRouterStaticVlanIndex	1.3.6.1.4.1.193.72.900.1.9.9.1.1	Unsigned32	not-accessible	This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB.
POR igmpSnoopRouterStaticPorts	1.3.6.1.4.1.193.72.900.1.9.9.1.2	PortList	read-create	The set of ports which are static router ports.
INT igmpSnoopRouterStaticStatus	1.3.6.1.4.1.193.72.900.1.9.9.1.3	INTEGER	read-create	Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry.
igmpSnoopMulticastCurrentTable	1.3.6.1.4.1.193.72.900.1.9.10		not-accessible	Table for current multicast addresses.
igmpSnoopMulticastCurrentEntry	1.3.6.1.4.1.193.72.900.1.9.10.1		not-accessible	Entry for current multicast addresses.
U32 igmpSnoopMulticastCurrentVlanIndex	1.3.6.1.4.1.193.72.900.1.9.10.1.1	Unsigned32	not-accessible	This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB.
IP igmpSnoopMulticastCurrentIpAddress	1.3.6.1.4.1.193.72.900.1.9.10.1.2	IpAddress	not-accessible	IP address of multicast group.
POR igmpSnoopMulticastCurrentPorts	1.3.6.1.4.1.193.72.900.1.9.10.1.3	PortList	read-only	The set of ports which are members.
POR igmpSnoopMulticastCurrentStatus	1.3.6.1.4.1.193.72.900.1.9.10.1.4	PortList	read-only	The set of ports which are static members.
igmpSnoopMulticastStaticTable	1.3.6.1.4.1.193.72.900.1.9.11		not-accessible	Table for static multicast addresses.
igmpSnoopMulticastStaticEntry	1.3.6.1.4.1.193.72.900.1.9.11.1		not-accessible	Entry for static multicast addresses.
U32 igmpSnoopMulticastStaticVlanIndex	1.3.6.1.4.1.193.72.900.1.9.11.1.1	Unsigned32	not-accessible	This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB.
IP igmpSnoopMulticastStaticIpAddress	1.3.6.1.4.1.193.72.900.1.9.11.1.2	IpAddress	not-accessible	IP address of multicast group.
POR igmpSnoopMulticastStaticPorts	1.3.6.1.4.1.193.72.900.1.9.11.1.3	PortList	read-create	The set of ports which are members.
INT igmpSnoopMulticastStaticStatus	1.3.6.1.4.1.193.72.900.1.9.11.1.4	INTEGER	read-create	Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry.
ipMgt	1.3.6.1.4.1.193.72.900.1.10
netConfigTable	1.3.6.1.4.1.193.72.900.1.10.1		not-accessible	A table of netConfigEntries.
netConfigEntry	1.3.6.1.4.1.193.72.900.1.10.1.1		not-accessible	A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is composed of the ifIndex assigned to the corresponding interface.
I32 netConfigIfIndex	1.3.6.1.4.1.193.72.900.1.10.1.1.1	Integer32	not-accessible	VLAN interface on which this entry is defined. This is defined as ifIndex in the IF-MIB.
IP netConfigIPAddress	1.3.6.1.4.1.193.72.900.1.10.1.1.2	IpAddress	not-accessible	The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device). If BOOTP is used, care should be taken to not send BOOTP broadcasts too frequently and to eventually send very infrequently if no replies are received.
IP netConfigSubnetMask	1.3.6.1.4.1.193.72.900.1.10.1.1.3	IpAddress	not-accessible	The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device). If BOOTP is used, care should be taken to not send BOOTP broadcasts too frequently and to eventually send very infrequently if no replies are received.
INT netConfigPrimaryInterface	1.3.6.1.4.1.193.72.900.1.10.1.1.4	INTEGER	read-create	Whether this is a primary interface.
INT netConfigUnnumbered	1.3.6.1.4.1.193.72.900.1.10.1.1.5	INTEGER	read-create	Whether this is an unnumbered interface.
ROW netConfigStatus	1.3.6.1.4.1.193.72.900.1.10.1.1.6	RowStatus	read-create	The status of this netConfigEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value.
IP netDefaultGateway	1.3.6.1.4.1.193.72.900.1.10.2	IpAddress	read-write	The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
INT ipHttpState	1.3.6.1.4.1.193.72.900.1.10.3	INTEGER	read-write	Whether HTTP is enabled.
INT ipHttpPort	1.3.6.1.4.1.193.72.900.1.10.4	INTEGER	read-write	The port number for HTTP.
INT ipDhcpRestart	1.3.6.1.4.1.193.72.900.1.10.5	INTEGER	read-write	Write it to restart(1) to restart DHCP. When read, this value always returns noRestart(2).
INT ipHttpsState	1.3.6.1.4.1.193.72.900.1.10.6	INTEGER	read-write	Whether HTTPS is enabled.
INT ipHttpsPort	1.3.6.1.4.1.193.72.900.1.10.7	INTEGER	read-write	The port number for HTTPS.
bcastStormMgt	1.3.6.1.4.1.193.72.900.1.11
bcastStormTable	1.3.6.1.4.1.193.72.900.1.11.1		not-accessible	Table of descriptive and status information about configuration of each switch ports(including expansion slot) in this system.
bcastStormEntry	1.3.6.1.4.1.193.72.900.1.11.1.1		not-accessible	An entry in the table, containing information about configuration in one switch port of the switch.
I32 bcastStormIfIndex	1.3.6.1.4.1.193.72.900.1.11.1.1.1	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
INT bcastStormStatus	1.3.6.1.4.1.193.72.900.1.11.1.1.2	INTEGER	read-write	Whether broadcast storm protection is enabled.
INT bcastStormSampleType	1.3.6.1.4.1.193.72.900.1.11.1.1.3	INTEGER	read-write	Sample type. If this is pkt-rate(1), then bcastStormPktRate is valid. If this is octet-rate(2), then bcastStormOctetRate is valid. If this is percent(3), then bcastStormPercent is valid.
INT bcastStormPktRate	1.3.6.1.4.1.193.72.900.1.11.1.1.4	INTEGER	read-write	Broadcast storm threshold as packets per second.
INT bcastStormOctetRate	1.3.6.1.4.1.193.72.900.1.11.1.1.5	INTEGER	read-write	Broadcast storm threshold as octets per second.
INT bcastStormPercent	1.3.6.1.4.1.193.72.900.1.11.1.1.6	INTEGER	read-write	Broadcast storm threshold as percentage of bandwidth.
vlanMgt	1.3.6.1.4.1.193.72.900.1.12
vlanTable	1.3.6.1.4.1.193.72.900.1.12.1		not-accessible	Table for VLAN configuration.
vlanEntry	1.3.6.1.4.1.193.72.900.1.12.1.1		not-accessible	Entry for VLAN configuration.
U32 vlanIndex	1.3.6.1.4.1.193.72.900.1.12.1.1.1	Unsigned32	not-accessible	Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.
INT vlanAddressMethod	1.3.6.1.4.1.193.72.900.1.12.1.1.2	INTEGER	read-write	Method to get the IP address.
vlanPortTable	1.3.6.1.4.1.193.72.900.1.12.2		not-accessible	Table for port configuration in VLAN.
vlanPortEntry	1.3.6.1.4.1.193.72.900.1.12.2.1		not-accessible	Entry for port configuration in VLAN.
I32 vlanPortIndex	1.3.6.1.4.1.193.72.900.1.12.2.1.1	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
INT vlanPortMode	1.3.6.1.4.1.193.72.900.1.12.2.1.2	INTEGER	read-write	This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) sets an access link.
priorityMgt	1.3.6.1.4.1.193.72.900.1.13
INT prioIpPrecDscpStatus	1.3.6.1.4.1.193.72.900.1.13.1	INTEGER	read-write	Whether IP precedence or DSCP look-up is enabled.
prioIpPrecTable	1.3.6.1.4.1.193.72.900.1.13.2		not-accessible	Table for IP precedence priority mapping.
prioIpPrecEntry	1.3.6.1.4.1.193.72.900.1.13.2.1		not-accessible	Entry for IP precendence priority mapping.
I32 prioIpPrecPort	1.3.6.1.4.1.193.72.900.1.13.2.1.2	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
I32 prioIpPrecValue	1.3.6.1.4.1.193.72.900.1.13.2.1.3	Integer32	not-accessible	Precedence value for this entry.
INT prioIpPrecCos	1.3.6.1.4.1.193.72.900.1.13.2.1.4	INTEGER	read-write	Class of service for this entry.
I32 prioIpPrecRestoreDefault	1.3.6.1.4.1.193.72.900.1.13.3	Integer32	read-write	This object is to restore IP Precedence settings of a port to default. To do this, write it to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, this object always returns 0.
prioIpDscpTable	1.3.6.1.4.1.193.72.900.1.13.4		not-accessible	Table for IP DSCP priority mapping.
prioIpDscpEntry	1.3.6.1.4.1.193.72.900.1.13.4.1		not-accessible	Entry for IP DSCP priority mapping.
I32 prioIpDscpPort	1.3.6.1.4.1.193.72.900.1.13.4.1.1	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
I32 prioIpDscpValue	1.3.6.1.4.1.193.72.900.1.13.4.1.2	Integer32	not-accessible	DSCP value for this entry.
INT prioIpDscpCos	1.3.6.1.4.1.193.72.900.1.13.4.1.3	INTEGER	read-write	Class of service for this entry.
I32 prioIpDscpRestoreDefault	1.3.6.1.4.1.193.72.900.1.13.5	Integer32	read-write	This object is to restore IP DSCP settings of a port to default. To do this, write it to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, this object always returns 0.
INT prioIpPortEnableStatus	1.3.6.1.4.1.193.72.900.1.13.6	INTEGER	read-write	Whether IP Port priority look-up is enabled.
prioIpPortTable	1.3.6.1.4.1.193.72.900.1.13.7		not-accessible	Table for IP port priority mapping.
prioIpPortEntry	1.3.6.1.4.1.193.72.900.1.13.7.1		not-accessible	Entry for IP port priority mapping.
I32 prioIpPortPhysPort	1.3.6.1.4.1.193.72.900.1.13.7.1.1	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
I32 prioIpPortValue	1.3.6.1.4.1.193.72.900.1.13.7.1.2	Integer32	not-accessible	IP port for this value.
INT prioIpPortCos	1.3.6.1.4.1.193.72.900.1.13.7.1.3	INTEGER	read-create	Class of service for this entry.
INT prioIpPortStatus	1.3.6.1.4.1.193.72.900.1.13.7.1.4	INTEGER	read-create	Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry.
prioCopy	1.3.6.1.4.1.193.72.900.1.13.8
OCT prioCopyIpPrec	1.3.6.1.4.1.193.72.900.1.13.8.1	OCTET STRING	read-write	Action to copy IP Precedence settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (big-endian) order. Starting from the 5th octet is destination port list in a form described by PortList in the Q-BRIDGE-MIB. Writing this object will perform copy. Reading this object will always get a zero-length octet string.
OCT prioCopyIpDscp	1.3.6.1.4.1.193.72.900.1.13.8.2	OCTET STRING	read-write	Action to copy IP DSCP settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (big-endian) order. Starting from the 5th octet is destination port list in a form described by PortList in the Q-BRIDGE-MIB. Writing this object will perform copy. Reading this object will always get a zero-length octet string.
OCT prioCopyIpPort	1.3.6.1.4.1.193.72.900.1.13.8.3	OCTET STRING	read-write	Action to copy IP Port settings from a source port to many destination ports. The first four octets represent an integer for the source port, in high-to-low (big-endian) order. Starting from the 5th octet is destination port list in a form described by PortList in the Q-BRIDGE-MIB. Writing this object will perform copy. Reading this object will always get a zero-length octet string.
prioWrrTable	1.3.6.1.4.1.193.72.900.1.13.9		not-accessible	Table for weighted round robin (WRR).
prioWrrEntry	1.3.6.1.4.1.193.72.900.1.13.9.1		not-accessible	Entry for weighted round robin (WRR).
INT prioWrrTrafficClass	1.3.6.1.4.1.193.72.900.1.13.9.1.1	INTEGER	not-accessible	Traffic class for this entry, as defined in dot1dTrafficClass in the Q-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTrafficClasses-1.
INT prioWrrWeight	1.3.6.1.4.1.193.72.900.1.13.9.1.2	INTEGER	read-write	Weight for this entry.
trapDestMgt	1.3.6.1.4.1.193.72.900.1.14
trapDestTable	1.3.6.1.4.1.193.72.900.1.14.1		not-accessible	A list of trap destination entries.
trapDestEntry	1.3.6.1.4.1.193.72.900.1.14.1.1		not-accessible	This entry includes a destination IP address to which to send traps for this community.
IP trapDestAddress	1.3.6.1.4.1.193.72.900.1.14.1.1.1	IpAddress	not-accessible	The address to send traps.
OCT trapDestCommunity	1.3.6.1.4.1.193.72.900.1.14.1.1.2	OCTET STRING	read-create	A community to which this destination address belongs.
INT trapDestStatus	1.3.6.1.4.1.193.72.900.1.14.1.1.3	INTEGER	read-create	Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry.
INT trapDestVersion	1.3.6.1.4.1.193.72.900.1.14.1.1.4	INTEGER	read-create	This variables represent the version of the Trap we wish to send to trap Receiver, if the value is 1, mean we wish to send Version 1 trap, if the value is 2, mean we wish to send version 2 trap.
trapVar	1.3.6.1.4.1.193.72.900.1.14.2
OID trapVarMibObjId	1.3.6.1.4.1.193.72.900.1.14.2.8	OBJECT IDENTIFIER	accessible-for-notify	Object ID of the mib variable.
qosMgt	1.3.6.1.4.1.193.72.900.1.16
rateLimitMgt	1.3.6.1.4.1.193.72.900.1.16.1
ENA rateLimitStatus	1.3.6.1.4.1.193.72.900.1.16.1.1	EnabledStatus	read-write	Whether rate limit is enabled.
rateLimitPortTable	1.3.6.1.4.1.193.72.900.1.16.1.2		not-accessible	Table for rate limit of each port.
rateLimitPortEntry	1.3.6.1.4.1.193.72.900.1.16.1.2.1		not-accessible	Entry for rate limit of each port.
I32 rlPortIndex	1.3.6.1.4.1.193.72.900.1.16.1.2.1.1	Integer32	not-accessible	The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
I32 rlPortInputLimit	1.3.6.1.4.1.193.72.900.1.16.1.2.1.2	Integer32	read-write	Value of the input rate limit. Its unit is megabits per second. For a 100 Mb/s port, the range is 1 to 100. For a 1000 Mb/s port, the range is 1 to 1000.
I32 rlPortOutputLimit	1.3.6.1.4.1.193.72.900.1.16.1.2.1.3	Integer32	read-write	Value of the output rate limit. Its unit is megabits per second. For a 100 Mb/s port, the range is 1 to 100. For a 1000 Mb/s port, the range is 1 to 1000.
ENA rlPortInputStatus	1.3.6.1.4.1.193.72.900.1.16.1.2.1.6	EnabledStatus	read-write	Whether input rate limit is enabled for this port.
ENA rlPortOutputStatus	1.3.6.1.4.1.193.72.900.1.16.1.2.1.7	EnabledStatus	read-write	Whether output rate limit is enabled for this port.
securityMgt	1.3.6.1.4.1.193.72.900.1.17
privateVlanMgt	1.3.6.1.4.1.193.72.900.1.17.1
privateVlanVlanTable	1.3.6.1.4.1.193.72.900.1.17.1.4		not-accessible	A table containing Private VLAN information on the VLANs which currently exist.
privateVlanVlanEntry	1.3.6.1.4.1.193.72.900.1.17.1.4.1		not-accessible	A conceptual row containing the Private VLAN information on the VLANs for a particular management domain.
I32 privateVlanVlanIndex	1.3.6.1.4.1.193.72.900.1.17.1.4.1.1	Integer32	not-accessible	The VLAN-id of this private VLAN.
INT privateVlanVlanType	1.3.6.1.4.1.193.72.900.1.17.1.4.1.2	INTEGER	read-create	The VLAN type as defined for Private VLAN feature. Set the value to invalid(1) to destory an entry, set other value to create an entry, if an index is already exist, set other to modifiy. Note that a VLAN's Private VLAN type can not be changed once it already has any ports in it.
I32 privateVlanAssoicatedPrimaryVlan	1.3.6.1.4.1.193.72.900.1.17.1.4.1.3	Integer32	read-create	The VLAN ID of the associated primary VLAN used for the Private VLAN feature if privateVlanVlanType has the value of isolated(3), community(4). If privateVlanVlanType has the value of primary(2), then this object has the value of 0. Note that one isolated VLAN can only be associated with one unique primary VLAN. One primary VLAN can only be associated with one isolated VLAN. One primary VLAN can be associated with multiple VLANs of community type; one community VLAN can only be associated with one unique primary VLAN.
portSecurityMgt	1.3.6.1.4.1.193.72.900.1.17.2
portSecPortTable	1.3.6.1.4.1.193.72.900.1.17.2.1		not-accessible	The Port Security(MAC bindind) Table
portSecPortEntry	1.3.6.1.4.1.193.72.900.1.17.2.1.1		not-accessible	The entry of portSecPortTable
I32 portSecPortIndex	1.3.6.1.4.1.193.72.900.1.17.2.1.1.1	Integer32	not-accessible	The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.
ENA portSecPortStatus	1.3.6.1.4.1.193.72.900.1.17.2.1.1.2	EnabledStatus	read-write	Set enabled(1) to enable port security and set disabled(2) to disable port security.
INT portSecAction	1.3.6.1.4.1.193.72.900.1.17.2.1.1.3	INTEGER	read-write	The corresponding actions that will take place when a port is under intruded, when this variable is set to none(1), no action will perform, when this variable is set to trap(2), a swPortSecurityTrap trap will send, when this variable is set to shutdown(3), the port will shutdown, when this variable is set to trapAndShutdown(4), a swPortSecurityTrap will send and the port will shutdown.
I32 portSecMaxMacCount	1.3.6.1.4.1.193.72.900.1.17.2.1.1.4	Integer32	read-write	The maximun number of MAC addresses that will be learned and locked. When we change the value of this variable, if the portSecPortStatus is enabled, we will discard all secure MAC and begin to learn again, until the number of MAC has reached this value, and only the secure MAC addresses can enter this port. If the portSecPortStatus is disabled, we will begin to learn the MAC, and auto enabled the portSecPortStatus when the MAC has reached this value.
radiusMgt	1.3.6.1.4.1.193.72.900.1.17.4
IP radiusServerAddress	1.3.6.1.4.1.193.72.900.1.17.4.1	IpAddress	read-write	IP address of RADIUS server.
INT radiusServerPortNumber	1.3.6.1.4.1.193.72.900.1.17.4.2	INTEGER	read-write	IP port number of RADIUS server.
STR radiusServerKey	1.3.6.1.4.1.193.72.900.1.17.4.3	DisplayString	read-write	Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string.
INT radiusServerRetransmit	1.3.6.1.4.1.193.72.900.1.17.4.4	INTEGER	read-write	Maximum number of retransmissions for RADIUS.
INT radiusServerTimeout	1.3.6.1.4.1.193.72.900.1.17.4.5	INTEGER	read-write	Timeout for RADIUS.
tacacsMgt	1.3.6.1.4.1.193.72.900.1.17.5
IP tacacsServerAddress	1.3.6.1.4.1.193.72.900.1.17.5.1	IpAddress	read-write	IP address of TACACS server.
I32 tacacsServerPortNumber	1.3.6.1.4.1.193.72.900.1.17.5.2	Integer32	read-write	IP port number of TACACS server.
STR tacacsServerKey	1.3.6.1.4.1.193.72.900.1.17.5.3	DisplayString	read-write	The encryption key used to authenticate logon access for the client using TACAS. Do not use blank spaces in the string. (Maximum length: 20 characters). This variable can only be set. When this variable is read, it always returns a zero-length string.
sshMgt	1.3.6.1.4.1.193.72.900.1.17.6
ENA sshServerStatus	1.3.6.1.4.1.193.72.900.1.17.6.1	EnabledStatus	read-write	The status of Secure Shell Server, set this value to 1 to enable SSH server, set this value to 2 to disable the SSH server.
I32 sshServerMajorVersion	1.3.6.1.4.1.193.72.900.1.17.6.2	Integer32	read-only	The major version of the SSH Server.
I32 sshServerMinorVersion	1.3.6.1.4.1.193.72.900.1.17.6.3	Integer32	read-only	The minor version of the SSH Server.
INT sshTimeout	1.3.6.1.4.1.193.72.900.1.17.6.4	INTEGER	read-write	The time interval that the router waits for the SSH client to respond. The range is 1-120.
INT sshAuthRetries	1.3.6.1.4.1.193.72.900.1.17.6.5	INTEGER	read-write	The number of attempts after which the interface is reset. The range is 1-5.
sshConnInfoTable	1.3.6.1.4.1.193.72.900.1.17.6.6		not-accessible	The table for Secure Shell Connection.
sshConnInfoEntry	1.3.6.1.4.1.193.72.900.1.17.6.6.1		not-accessible	The conceptual row for sshConnInfoTable.
I32 sshConnID	1.3.6.1.4.1.193.72.900.1.17.6.6.1.1	Integer32	not-accessible	The connection ID of the Secure Shell Connection.
I32 sshConnMajorVersion	1.3.6.1.4.1.193.72.900.1.17.6.6.1.2	Integer32	read-only	The SSH major version.
I32 sshConnMinorVersion	1.3.6.1.4.1.193.72.900.1.17.6.6.1.3	Integer32	read-only	The SSH minor version.
INT sshConnEncryptionType	1.3.6.1.4.1.193.72.900.1.17.6.6.1.4	INTEGER	read-only	The encryption type of the SSH. none(1) mean no encrytion , des(2) mean using DES encrytion, tribeDes mean using 3DES encrytion.
INT sshConnStatus	1.3.6.1.4.1.193.72.900.1.17.6.6.1.5	INTEGER	read-only	The SSH connection State. negotiationStart(1) mean the SSH is in its negotiation start state, authenticationStart(2) mean the SSH is in authentication start state, sessionStart(3) mean the SSH is in session start State.
OCT sshConnUserName	1.3.6.1.4.1.193.72.900.1.17.6.6.1.6	OCTET STRING	read-only	The user name of the connection.
INT sshDisconnect	1.3.6.1.4.1.193.72.900.1.17.6.6.1.7	INTEGER	read-write	Set the variables to disconnect to disconnect the connection, when read, this variables always return noDisconnect(1).
sysLogMgt	1.3.6.1.4.1.193.72.900.1.19
INT sysLogStatus	1.3.6.1.4.1.193.72.900.1.19.1	INTEGER	read-write	Whether system log is enabled.
INT sysLogHistoryFlashLevel	1.3.6.1.4.1.193.72.900.1.19.2	INTEGER	read-write	Severity level for logging to flash.
INT sysLogHistoryRamLevel	1.3.6.1.4.1.193.72.900.1.19.3	INTEGER	read-write	Severity level for logging to RAM.
lineMgt	1.3.6.1.4.1.193.72.900.1.20
consoleMgt	1.3.6.1.4.1.193.72.900.1.20.1
INT consoleDataBits	1.3.6.1.4.1.193.72.900.1.20.1.1	INTEGER	read-write	Number of data bits.
INT consoleParity	1.3.6.1.4.1.193.72.900.1.20.1.2	INTEGER	read-write	Define the generation of a parity bit.
INT consoleBaudRate	1.3.6.1.4.1.193.72.900.1.20.1.3	INTEGER	read-write	Baud rate. Valid values are 115200, 57600, 38400, 19200, and 9600.
INT consoleStopBits	1.3.6.1.4.1.193.72.900.1.20.1.4	INTEGER	read-write	The stop Bits of the console, valid value is stopbits1(1) or stopbits2(2)
INT consoleExecTimeout	1.3.6.1.4.1.193.72.900.1.20.1.5	INTEGER	read-write	In serial console, use the consoleExecTimeout variables to set the interval that the EXEC command interpreter waits until user input is detected, set the value to 0 to disable it.
INT consolePasswordThreshold	1.3.6.1.4.1.193.72.900.1.20.1.6	INTEGER	read-write	In serial console, use the consolePasswordThreshold variabes to set the password intrusion threshold, which limits the number of failed logon attempts allowed. Set it value to 0 to disable it.
INT consoleSilentTime	1.3.6.1.4.1.193.72.900.1.20.1.7	INTEGER	read-write	In Console, Use the consoleSilentTime variable to set the amount of time the management console is inaccessible after the number of unsuccessful logon attempts exceeds the threshold set by the password-thresh command. Set it to 0 to disable it.
telnetMgt	1.3.6.1.4.1.193.72.900.1.20.2
INT telnetExecTimeout	1.3.6.1.4.1.193.72.900.1.20.2.1	INTEGER	read-write	In a telnet session, to set the interval that the EXEC command interpreter waits until user input is detected, use the telnetExecTimeout variables.
INT telnetPasswordThreshold	1.3.6.1.4.1.193.72.900.1.20.2.2	INTEGER	read-write	In a telnet session, use the consolePasswordThreshold variabes to set the password intrusion threshold, which limits the number of failed logon attempts allowed. Set it value to 0 to disable it.
sysTimeMgt	1.3.6.1.4.1.193.72.900.1.23
sntpMgt	1.3.6.1.4.1.193.72.900.1.23.1
ENA sntpStatus	1.3.6.1.4.1.193.72.900.1.23.1.1	EnabledStatus	read-write	Set enabled(1) to enable the SNTP, set disabled(2) to disable the SNTP.
INT sntpServiceMode	1.3.6.1.4.1.193.72.900.1.23.1.2	INTEGER	read-write	Service mode.
I32 sntpPollInterval	1.3.6.1.4.1.193.72.900.1.23.1.3	Integer32	read-write	Polling interval.
sntpServerTable	1.3.6.1.4.1.193.72.900.1.23.1.4		not-accessible	Table for SNTP servers
sntpServerEntry	1.3.6.1.4.1.193.72.900.1.23.1.4.1		not-accessible	Entry for SNTP servers.
I32 sntpServerIndex	1.3.6.1.4.1.193.72.900.1.23.1.4.1.1	Integer32	not-accessible	The index of a server. This table has fixed size.
IP sntpServerIpAddress	1.3.6.1.4.1.193.72.900.1.23.1.4.1.2	IpAddress	read-write	The IP address of a server. Valid IP addresses must occupy contiguous indexes. All IP addresses after the last valid index is 0.
STR sysCurrentTime	1.3.6.1.4.1.193.72.900.1.23.2	DisplayString	read-write	It is a text string in the following form, based on Unix: 'Mmm _d hh:mm:ss yyyy'. 'Mmm' is the first three letters of the English name of the month. '_d' is the day of month. A single-digit day is preceded by the space. 'hh:mm:ss' is a 24-hour representations of hours, minutes, and seconds. A single-digit hour is preceded by a zero. 'yyyy' is the four-digit year. An example is: 'Jan 1 02:03:04 2002'.
STR sysTimeZone	1.3.6.1.4.1.193.72.900.1.23.3	DisplayString	read-write	It is a text string in the following form: '[s]hh:mm'. '[s]' is a plus-or-minus sign. For UTC, this is omitted. For a positive offset, this is '+'. For a negative offset, this is '-'. 'hh:mm' in the hour and minute offset from UTC. A single-digit hour is preceded by a zero.
STR sysTimeZoneName	1.3.6.1.4.1.193.72.900.1.23.4	DisplayString	read-write	The name of the time zone.
fileMgt	1.3.6.1.4.1.193.72.900.1.24
fileCopyMgt	1.3.6.1.4.1.193.72.900.1.24.1
INT fileCopySrcOperType	1.3.6.1.4.1.193.72.900.1.24.1.1	INTEGER	read-write	The Copy Operation in which we want to perform to the fileCopyDestOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDestOperType'. file(1) means we want to perform the 'copy file fileCopyDestType' operation, runningCfg(2) means we want to perform the 'copy running-config fileCopyDestOperType' operation, startUpCfg(3) means we want to perform the 'copy startup-config fileCopyDestOperType' operation, tftp(4) means we want to perform the 'copy tftp fileCopyDestOperType' operation, unit(5) is only avaiable in stacking system, in which we can copy files from one unit to another unit and it means we want to perform the 'copy unit fileCopyDestOperType' operation. The possible permuations is as follow: (1)copy file file (2)copy file runningCfg (3) copy file startUpCfg (4)copy file tftp (5) copy file unit(for stacking system only) (6)copy runningCfg file (7)copy runningCfg startUpCfg (8)copy runningCfg tftp (9)copy startupCfg file (10)copy startupCfg runningcfg (11)copy startupCfg tftp (12)copy tftp file (13)copy tftp runningCfg (14)copy tftp startUpCfg (15)copy unit file.
STR fileCopySrcFileName	1.3.6.1.4.1.193.72.900.1.24.1.2	DisplayString	read-write	The source file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to the zero length string when no file name has been specified. Note: if the fileCopySrcOperType is runningCfg(2) or startUpCfg(3), this varible can be ignored.
INT fileCopyDestOperType	1.3.6.1.4.1.193.72.900.1.24.1.3	INTEGER	read-write	The Copy Operation in which we want to perform from the fileCopySrcOperType, this operation is similar to the CLI command 'copy fileCopySrcOperType fileCopyDestOperType'. file(1) means we want to perform the 'copy fileCopySrcType file ' operation, runningCfg(2) means we want to perform the 'copy fileCopySrcOperType running-config ' operation, startUpCfg(3) means we want to perform the 'copy fileCopySrcOperType startup-config ' operation, tftp(4) means we want to perform the 'copy fileCopySrcOperType tftp' operation, unit(5) is only avaiable in stacking system, in which we can copy files from one unit to another unit and it means we want to perform the 'copy fileCopySrcOperType unit' operation. The possible permuations is as follow: (1)copy file file (2)copy file runningCfg (3) copy file startUpCfg (4)copy file tftp (5) copy file unit(for stacking system only) (6)copy runningCfg file (7)copy runningCfg startUpCfg (8)copy runningCfg tftp (9)copy startupCfg file (10)copy startupCfg runningcfg (11)copy startupCfg tftp (12)copy tftp file (13)copy tftp runningCfg (14)copy tftp startUpCfg (15)copy unit file.
STR fileCopyDestFileName	1.3.6.1.4.1.193.72.900.1.24.1.4	DisplayString	read-write	The destination file name for fileCopyMgt when a copy operation is next requested via this MIB. This value is set to the zero length string when no file name has been specified. Note: if the fileCopyDestOperType is runningCfg(2) or startupCfg(3), this varible can be ignored.
INT fileCopyFileType	1.3.6.1.4.1.193.72.900.1.24.1.5	INTEGER	read-write	Type of file to copy in fileCopyMgt. If the fileCopySrcOperType or fileCopyDestOperType is either runningCfg(2) or startupCfg(3), this varible can be ignored. If the fileCopySrcOperType or fileCopyDestOperType is unit(5), this varibles cannot be set to bootRom(3).
IP fileCopyTftpServer	1.3.6.1.4.1.193.72.900.1.24.1.6	IpAddress	read-write	The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to '0.0.0.0' when no IP address has been specified. If neither fileCopySrcOperType nor fileCopyDestOperType is tftp(4), this variable can be ignored.
I32 fileCopyUnitId	1.3.6.1.4.1.193.72.900.1.24.1.7	Integer32	read-write	Specify the unit of the switch for stackable device when performing the 'copy unit file' or 'copy file unit' action, If neither fileCopySrcOperType nor fileCopyDestOperType is unit(5), this variable can be ignored.
INT fileCopyAction	1.3.6.1.4.1.193.72.900.1.24.1.8	INTEGER	read-write	Setting this object to copy(2) to begin the copy Operation.
INT fileCopyStatus	1.3.6.1.4.1.193.72.900.1.24.1.9	INTEGER	read-only	The status of the last copy procedure, if any. This object will have a value of downloadStatusUnknown(2) if no copy operation has been performed.
fileInfoMgt	1.3.6.1.4.1.193.72.900.1.24.2
fileInfoTable	1.3.6.1.4.1.193.72.900.1.24.2.1		not-accessible	This table contain the information of the file system, we can also perfrom the delete, set startup file operation.
fileInfoEntry	1.3.6.1.4.1.193.72.900.1.24.2.1.1		not-accessible	A conceptually row for fileInfoTable.
I32 fileInfoUnitID	1.3.6.1.4.1.193.72.900.1.24.2.1.1.1	Integer32	not-accessible	The unit of the switch in a stacking system, in a non-stacking system, it value is always 1.
OCT fileInfoFileName	1.3.6.1.4.1.193.72.900.1.24.2.1.1.2	OCTET STRING	not-accessible	The file Name of the file System in the device.
INT fileInfoFileType	1.3.6.1.4.1.193.72.900.1.24.2.1.1.3	INTEGER	read-only	The file type of the file System in the device.
T/F fileInfoIsStartUp	1.3.6.1.4.1.193.72.900.1.24.2.1.1.4	TruthValue	read-write	This flag indicate whether this file is a startup file, Setting this object to truth(1) to indicate this is a startup file, setting this object to false(2) is a invalid operation.
I32 fileInfoFileSize	1.3.6.1.4.1.193.72.900.1.24.2.1.1.5	Integer32	read-only	The sizes( in bytes) of the file.
STR fileInfoCreationTime	1.3.6.1.4.1.193.72.900.1.24.2.1.1.6	DisplayString	read-only	The creation time of the file.
INT fileInfoDelete	1.3.6.1.4.1.193.72.900.1.24.2.1.1.7	INTEGER	read-write	Writing this object to delete(2) to delete a file, when read, this always return noDelete(1).
ledCtrlMgt	1.3.6.1.4.1.193.72.900.1.27
INT ledCtrlMgtColorOnOffTime	1.3.6.1.4.1.193.72.900.1.27.1	INTEGER	read-write	Indicates the control led color and on off time.
esn310Notifications	1.3.6.1.4.1.193.72.900.2
esn310Traps	1.3.6.1.4.1.193.72.900.2.1
esn310TrapsPrefix	1.3.6.1.4.1.193.72.900.2.1.0
NTF swPowerStatusChangeTrap	1.3.6.1.4.1.193.72.900.2.1.0.1			This trap is sent when the power status of an individual power changes.
NTF swSettingToAllInterfacesTrap	1.3.6.1.4.1.193.72.900.2.1.0.42			This trap is issued when a MIB object defined on a per-interface basis is being set, but because of a system limitation, this set action is applied to all interfaces.
esn310Conformance	1.3.6.1.4.1.193.72.900.3

RFC description

Manages Ericsson ESN310 switches with support for VLANs, QoS, security, and trunk configurations.

Start monitoring ESN310-series managed Ethernet switch (Accton-derived OEM) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ESN310-MIB