AVIAT-ALARM-REPORTING-MIB

All MIBs › AVIAT-ALARM-REPORTING-MIB

Organization: Aviat Networks

Last Updated: 2016-05-26

Category: Alarm and Event Management, Vendor: Aviat

Description: Manages alarm reporting configuration and active fault notifications for Aviat microwave radio systems.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is AVIAT-ALARM-REPORTING-MIB?

AVIAT-ALARM-REPORTING-MIB manages alarm reporting configuration and describes the status of active faults for Aviat Networks microwave radio transmission equipment, a technology used in point-to-point wireless backhaul links. Its data centers on fault/alarm status: which alarms are currently active on the radio system, their configuration, and reporting behavior, rather than raw performance counters. As a fault-monitoring MIB, it is specifically geared toward hardware status monitoring — surfacing conditions like radio link failures, hardware faults, or environmental alarms (e.g., power or transceiver issues) on the microwave radio units. It relies on the standard SNMP notification/trap framework and the Aviat enterprise OID tree, and may be used alongside other Aviat radio-performance or inventory MIBs. It is deployed in telecom and utility microwave backhaul networks where Aviat radios link cell towers or remote sites. Engineers can download the AVIAT-ALARM-REPORTING-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in AVIAT-ALARM-REPORTING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Aviat Networks microwave radio (point-to-point wireless backhaul)

Monitoring Examples

No specific object or table names were captured in the sampled source, so concrete leaf objects cannot be cited; however, given its stated purpose an admin would expect to poll or receive traps for an active-alarm table reflecting current fault conditions on the microwave radio (e.g., link failure, RF transmit/receive faults). An alarm transitioning from clear to active would indicate a degraded or failed radio link requiring dispatch. This is inferred from the module's description rather than confirmed sampled objects.

What Can Be Monitored

active alarm status
alarm configuration
radio link fault conditions

Imported Objects

From AVIAT-TEXTCONVENTION-MIB

AviatYangIdentityRef

From IANA-ITU-ALARM-TC-MIB

IANAItuEventType
IANAItuProbableCause

From ITU-ALARM-TC-MIB

ItuPerceivedSeverity

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DateAndTime
DisplayString
TEXTUAL-CONVENTION
TruthValue

From STXN-GLOBALREGISTER-MIB

aviatModules

OBJECT-IDENTITY

How to Use in IPNetwork Monitor

Example using aviatAlarmInstanceStatusChangeCount OID:

Select an Aviat Networks microwave radio link (point-to-point backhaul) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type aviatAlarmInstanceStatusChangeCount into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of times that the entity has raised or lowered this alarm instance since the system was started. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
aviatAlarmReportingModule	1.3.6.1.4.1.2509.9.47			This MIB module is used to describe the status of alarms present in Aviat Networks products.
aviatAlarmReportingMIBEvents	1.3.6.1.4.1.2509.9.47.0
NTF aviatAlarmRaisedInstanceNotification	1.3.6.1.4.1.2509.9.47.0.1			This notification is generated whenever a system alarm is raised.
NTF aviatAlarmClearedInstanceNotification	1.3.6.1.4.1.2509.9.47.0.2			This notification is generated whenever a system alarm is cleared.
NTF aviatAlarmUnstableInstanceNotification	1.3.6.1.4.1.2509.9.47.0.3			This notification is generated whenever a system alarm is suspended.
NTF aviatAlarmStabilizedInstanceNotification	1.3.6.1.4.1.2509.9.47.0.4			This notification is generated whenever a system alarm suspension is cleared.
aviatAlarmReportingConformance	1.3.6.1.4.1.2509.9.47.1
aviatAlarmReportingGroups	1.3.6.1.4.1.2509.9.47.1.1
aviatAlarmReportingObjectGroup	1.3.6.1.4.1.2509.9.47.1.1.1			These are the objects for alarms in the Alarm MIB.
aviatAlarmReportingNotifyGroup	1.3.6.1.4.1.2509.9.47.1.1.2			Alarm notifications defined in this MIB.
aviatAlarmReportingCompliance	1.3.6.1.4.1.2509.9.47.1.2
aviatAlarmReportingComplV1	1.3.6.1.4.1.2509.9.47.1.2.1			The implementation requirements for this MIB.
aviatAlarmReportingMIBObjects	1.3.6.1.4.1.2509.9.47.2
aviatAlarmTypeTable	1.3.6.1.4.1.2509.9.47.2.1		not-accessible	This is a table containing information for all alarms types that are supported by the system.
aviatAlarmTypeEntry	1.3.6.1.4.1.2509.9.47.2.1.1		not-accessible	This is a row in the table holding information about a single supported alarm type.
AVI aviatAlarmTypeIndex	1.3.6.1.4.1.2509.9.47.2.1.1.1	AviatYangIdentityRef	not-accessible	The unique Yang Identity representing a particular alarm type.
T/F aviatAlarmTypeSecurityEvent	1.3.6.1.4.1.2509.9.47.2.1.1.2	TruthValue	read-only	Indicates whether or not the system views the alarm type as being security related.
STR aviatAlarmTypeDescription	1.3.6.1.4.1.2509.9.47.2.1.1.3	DisplayString	read-only	This object specifies a human-readable message describing the alarm type.
IAN aviatAlarmTypeEvent	1.3.6.1.4.1.2509.9.47.2.1.1.4	IANAItuEventType	read-only	The type of event associated with the alarm type.
ITU aviatAlarmTypeDefaultSeverity	1.3.6.1.4.1.2509.9.47.2.1.1.5	ItuPerceivedSeverity	read-only	This object specifies the default severity assigned to the alarm type by the system. By default, any entity that raises an alarm of this type will have this level of severity associated with the alarm instance. The following ITU-t X.733 severities are supported: critical (3) major (4) minor (5) warning (6) See http://www.iana.org.
DAT aviatAlarmInstanceLastChange	1.3.6.1.4.1.2509.9.47.2.2	DateAndTime	read-only	The time when any alarm instance in the system last changed its state.
aviatAlarmInstanceTable	1.3.6.1.4.1.2509.9.47.2.3		not-accessible	This is a table containing information for all alarm instances currently registered within the system.
aviatAlarmInstanceEntry	1.3.6.1.4.1.2509.9.47.2.3.1		not-accessible	This is a row in the table holding information for a given alarm instance.
IET aviatAlarmInstanceEntity	1.3.6.1.4.1.2509.9.47.2.3.1.1	IetfEntityName	not-accessible	Each alarm instance is associated with a particular system entity. This object identifies the entity in the form of a name string. Corresponds to the physical entity name as per the ietf-entity YANG.
T/F aviatAlarmInstanceSecurityEvent	1.3.6.1.4.1.2509.9.47.2.3.1.2	TruthValue	read-only	Indicates whether or not the system views the alarm instance as being security related.
STR aviatAlarmInstanceDescription	1.3.6.1.4.1.2509.9.47.2.3.1.3	DisplayString	read-only	This object specifies a human-readable message describing the alarm instance.
IAN aviatAlarmInstanceType	1.3.6.1.4.1.2509.9.47.2.3.1.4	IANAItuEventType	read-only	The type of event associated with the alarm instance.
AVI aviatAlarmInstanceCurrentState	1.3.6.1.4.1.2509.9.47.2.3.1.5	AviatAlarmInstanceState	read-only	The current state of the alarm instance. Supported states are: cleared (0) raised (1) unstable (2)
ITU aviatAlarmInstanceCurrentSeverity	1.3.6.1.4.1.2509.9.47.2.3.1.6	ItuPerceivedSeverity	read-only	This object shows the current severity level associated with the alarm instance: cleared (1) indetermined (2) critical (3) major (4) minor (5) warning (6)
ITU aviatAlarmInstanceRaisedSeverity	1.3.6.1.4.1.2509.9.47.2.3.1.7	ItuPerceivedSeverity	read-only	The severity to be applied when this alarm instance is raised for this entity. This is either based upon the default for the alarm type, or overriden by user configuration. The following ITU-t X.733 severities are supported: critical (3) major (4) minor (5) warning (6) See http://www.iana.org.
DAT aviatAlarmInstanceLastStatusChange	1.3.6.1.4.1.2509.9.47.2.3.1.8	DateAndTime	read-only	The time when the status of the alarm instance last changed.
C32 aviatAlarmInstanceStatusChangeCountEx	1.3.6.1.4.1.2509.9.47.2.3.1.9	Counter32	read-only	The number of times that the entity has raised or lowered this alarm instance since the system was started.
T/F aviatAlarmInstanceDisabled	1.3.6.1.4.1.2509.9.47.2.3.1.10	TruthValue	read-only	Indicates whether or not an event which causes this alarm instance to be raised or lowered by this entity, will be reported. When disabled, status changes for the alarm will still be shown in aviatAlarmInstanceTable, but the alarm instance will no longer appear in aviatAlarmRaisedInstanceTable, a log entry will not be made, and a notification will not be generated.
DAT aviatAlarmRaisedInstanceLastChange	1.3.6.1.4.1.2509.9.47.2.4	DateAndTime	read-only	The time of the last update to the raised alarms table.
aviatAlarmRaisedInstanceTable	1.3.6.1.4.1.2509.9.47.2.5		not-accessible	This is a table containing information for all alarm instances that are currently raised or unstable in the system.
aviatAlarmRaisedInstanceEntry	1.3.6.1.4.1.2509.9.47.2.5.1		not-accessible	This is a row in the table holding information for a given raised or unstable alarm instance.
T/F aviatAlarmRaisedInstanceSecurityEvent	1.3.6.1.4.1.2509.9.47.2.5.1.1	TruthValue	read-only	Indicates whether or not the system views the alarm instance as being security related.
STR aviatAlarmRaisedInstanceDescription	1.3.6.1.4.1.2509.9.47.2.5.1.2	DisplayString	read-only	This object specifies a human-readable message describing the alarm instance.
ITU aviatAlarmRaisedInstanceSeverity	1.3.6.1.4.1.2509.9.47.2.5.1.3	ItuPerceivedSeverity	read-only	This object shows the severity level associated with the alarm instance: critical (3) major (4) minor (5) warning (6)
IAN aviatAlarmRaisedInstanceCause	1.3.6.1.4.1.2509.9.47.2.5.1.4	IANAItuProbableCause	read-only	This object shows the probable cause of the alarm instance being active.
DAT aviatAlarmRaisedInstanceTime	1.3.6.1.4.1.2509.9.47.2.5.1.5	DateAndTime	read-only	The time when the alarm instance was raised.
T/F aviatAlarmRaisedInstanceIsUnstable	1.3.6.1.4.1.2509.9.47.2.5.1.6	TruthValue	read-only	An indication of whether the alarm instance is currently considered unstable, and hence has further state changes suspended until it is considered stable again.
aviatAlarmEntityTable	1.3.6.1.4.1.2509.9.47.2.6		not-accessible	This is a table containing information for all entities that have alarm instances registered against them.
aviatAlarmEntityEntry	1.3.6.1.4.1.2509.9.47.2.6.1		not-accessible	This is a row in the table holding information for a given entity.
AVI aviatAlarmEntityReportingMode	1.3.6.1.4.1.2509.9.47.2.6.1.1	AviatAlarmReportingMode	read-only	Indicates the alarm reporting mode configured for this entity. Supported modes are: all (0) nonSummary (1) summaryOnly (2) none (3) The mode dictates alarm instances of which alarm types against the entity shall generate a log entry and a notification upon state change or suppression change.
aviatAlarmReportingNotifications	1.3.6.1.4.1.2509.9.47.2.7
IET aviatAlarmEntityName	1.3.6.1.4.1.2509.9.47.2.7.1	IetfEntityName	accessible-for-notify	The name of the entity associated with the alarm instance. Only used for the generation of notifications.
AVI aviatAlarmTypeID	1.3.6.1.4.1.2509.9.47.2.7.2	AviatYangIdentityRef	accessible-for-notify	The index of the alarm type associated with the alarm instance. Only used for the generation of notifications.

RFC description

Alarm reporting and status monitoring for Aviat Networks wireless products.

Start monitoring Aviat Networks microwave radio links (point-to-point backhaul) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download AVIAT-ALARM-REPORTING-MIB