ASCEND-MIBE3ATMNET-MIB

All MIBs › ASCEND-MIBE3ATMNET-MIB

Category: ATM, Vendor: Ascend/Lucent

Description: Manages E3-based ATM network interface configuration and cell statistics on Ascend equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ASCEND-MIBE3ATMNET-MIB?

ASCEND-MIBE3ATMNET-MIB is a proprietary Ascend MIB managing E3-based ATM network interface configuration and cell statistics, the European counterpart to the DS3 ATM MIB in this family. It exposes E3 physical-line configuration and alarm status alongside ATM cell-layer performance counters for the interface. Its monitoring value centers on hardware and interface health: E3 line alarms reveal physical-layer problems such as loss of signal or framing errors, while ATM cell error and discard counters surface congestion or transmission faults on the trunk. It builds on standard E3 and ATM MIB conventions with Ascend-specific extensions layered on top. It was deployed on Ascend WAN edge/aggregation equipment connecting to carrier E3 ATM circuits, primarily in European and other E-carrier telecom environments, where technicians can still find an ASCEND-MIBE3ATMNET-MIB download for loading into legacy MIB browsers.

IPNetwork Monitor allows you to monitor SNMP objects defined in ASCEND-MIBE3ATMNET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ascend WAN edge/aggregation routers with E3 ATM interfaces

Monitoring Examples

An operator polls the E3 line alarm/status objects for loss-of-signal or framing-error indications on the physical circuit, together with ATM cell error and discard counters for the interface. An increase in cell discards paired with an active E3 alarm points to a degrading carrier circuit rather than a router-side misconfiguration. These counters are typically trended over time so a gradual increase in errors can be caught before the circuit fails outright.

What Can Be Monitored

E3 line alarm/error status
ATM cell error/discard counters
interface configuration parameters
physical-layer signal status

Imported Objects

From ASCEND-MIB

configuration

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT e3AtmNetworkProfile_Action_o	1.3.6.1.4.1.529.23.15.1.1.19	INTEGER	read-write
INT e3AtmNetworkProfile_Enabled	1.3.6.1.4.1.529.23.15.1.1.8	INTEGER	read-write	TRUE if the line is enabled, otherwise FALSE.
INT e3AtmNetworkProfile_IgnoreLineup	1.3.6.1.4.1.529.23.15.1.1.27	INTEGER	read-write	Ignore line up value for this port.
INT e3AtmNetworkProfile_Item_o	1.3.6.1.4.1.529.23.15.1.1.3	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_CellPayloadScramble	1.3.6.1.4.1.529.23.15.1.1.18	INTEGER	read-write	TRUE if the cell payload scrambling is enabled, otherwise FALSE.
INT e3AtmNetworkProfile_LineConfig_ClockPriority	1.3.6.1.4.1.529.23.15.1.1.22	INTEGER	read-write	Clock priority assigned to the E3-ATM line. Used to select a particular E3 line as clock source.
INT e3AtmNetworkProfile_LineConfig_ClockSource	1.3.6.1.4.1.529.23.15.1.1.21	INTEGER	read-write	Determine whether the 8KHz clock from the E3-ATM board is eligible to be used as the system-wide TDM clock source.
INT e3AtmNetworkProfile_LineConfig_FramerMode	1.3.6.1.4.1.529.23.15.1.1.16	INTEGER	read-write	The E3 ATM framer mode.
INT e3AtmNetworkProfile_LineConfig_HighTxOutput	1.3.6.1.4.1.529.23.15.1.1.15	INTEGER	read-write	TRUE if the E3 cable length is more than 300 ft, otherwise FALSE.
INT e3AtmNetworkProfile_LineConfig_IncomingVCCs_Enabled	1.3.6.1.4.1.529.23.15.3.1.5	INTEGER	read-write	TRUE if the item is enabled, otherwise FALSE.
INT e3AtmNetworkProfile_LineConfig_IncomingVCCs_EndVci	1.3.6.1.4.1.529.23.15.3.1.8	INTEGER	read-write	A number that identifies the ending Virtual Channel Identifier of this item.
INT e3AtmNetworkProfile_LineConfig_IncomingVCCs_Index_o	1.3.6.1.4.1.529.23.15.3.1.4	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_IncomingVCCs_Item_o	1.3.6.1.4.1.529.23.15.3.1.3	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_IncomingVCCs_Shelf_o	1.3.6.1.4.1.529.23.15.3.1.1	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_IncomingVCCs_Slot_o	1.3.6.1.4.1.529.23.15.3.1.2	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_IncomingVCCs_StartVci	1.3.6.1.4.1.529.23.15.3.1.7	INTEGER	read-write	A number that identifies the starting Virtual Channel Identifier of this item.
INT e3AtmNetworkProfile_LineConfig_IncomingVCCs_Vpi	1.3.6.1.4.1.529.23.15.3.1.6	INTEGER	read-write	A number that identifies the Virtual Path Identifier of this item.
INT e3AtmNetworkProfile_LineConfig_Loopback	1.3.6.1.4.1.529.23.15.1.1.14	INTEGER	read-write	Loopback mode.
INT e3AtmNetworkProfile_LineConfig_NailedGroup	1.3.6.1.4.1.529.23.15.1.1.10	INTEGER	read-write	A number that identifies the set of lines that makes up a nailed group. 0 means this line is not part of a nailed group.
INT e3AtmNetworkProfile_LineConfig_ReceiveEqualization	1.3.6.1.4.1.529.23.15.1.1.20	INTEGER	read-write	TRUE if receive equalization is needed, otherwise FALSE. Receive equalization is needed if the cable length is more than 300 ft.
INT e3AtmNetworkProfile_LineConfig_StatusChangeTrapEnable	1.3.6.1.4.1.529.23.15.1.1.28	INTEGER	read-write	When set to No, do not send dsx3LineStatusChangeTrapEnable trap. If Yes, send traps. The default is No.
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_Aggregate	1.3.6.1.4.1.529.23.15.2.1.9	INTEGER	read-write	If FALSE each individual VC gets the bit rate that is assigned to this shaper. If TRUE the VCs share the bit rate that is assigned to this shaper equally.
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_BitRate	1.3.6.1.4.1.529.23.15.2.1.6	INTEGER	read-write	What is the sustained rate in Kilobits per second that can be transmitted by the VC(s) when using this shaper. Limited by the framer mode and the interface type.
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_Enabled	1.3.6.1.4.1.529.23.15.2.1.5	INTEGER	read-write	TRUE if the shaper is enabled, otherwise FALSE.
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_Index_o	1.3.6.1.4.1.529.23.15.2.1.4	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_Item_o	1.3.6.1.4.1.529.23.15.2.1.3	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_MaxBurstSize	1.3.6.1.4.1.529.23.15.2.1.8	INTEGER	read-write	What is the maximum burst size in cell that can be transmitted during the peak rate by the VC(s) when using this shaper.
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_PeakRate	1.3.6.1.4.1.529.23.15.2.1.7	INTEGER	read-write	What is the peak rate in Kilobits per second that can be transmitted by the VC(s) when using this shaper. Limited by the framer mode and the interface type.
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_Priority	1.3.6.1.4.1.529.23.15.2.1.10	INTEGER	read-write	A number that represent the prioriy of the shaper in respect to other shapers. 0 is the highest priority and 15 is the lowest.
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_Shelf_o	1.3.6.1.4.1.529.23.15.2.1.1	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_TrafficShapers_Slot_o	1.3.6.1.4.1.529.23.15.2.1.2	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_TrunkGroup	1.3.6.1.4.1.529.23.15.1.1.9	INTEGER	read-write	The trunk group to which this line is assigned. 0 means this line is not part of a trunk group.
INT e3AtmNetworkProfile_LineConfig_VcSwitchingVpi	1.3.6.1.4.1.529.23.15.4.1.5	INTEGER	read-write	VPI(s) to be used for the VC switching (VCC). It should always contain VPI 0 for VC switching. All VC switching VPI have similar valid VCI range which is determined by 'vpi-vci-range' attribute. Rest of the VPIs will be used for the VP switching. The user needs to understand that adding a VPI in a list of VC switching VPI will allocate more VCCs for this port. The user needs to make sure that VCCs for the other ports have been reduced to accommodate increase in VCC for this port because system can support only 32k VCCs on all trunk ports combined. If vci-range is 4k and VPI 0 is the only VPI doing VC switching for this port than this port occupies 4k VCCs. If user adds VPI 1 to the list of VPIs to do VCC then total 8k VCCs are occupied for this port. System will reject the configuration if user tries to use more than 32k VCCs for all trunk ports combined. ANY CHANGES IN A LIST OF VPIs WILL BE EFFECTIVE IMMEDIATLY. IN ORDER TO DO THAT ALL CONNECTIONS WITHIN THIS SYSTEM WILL BE DROPPED AND REESTABLISHED.
INT e3AtmNetworkProfile_LineConfig_VcSwitchingVpi_Index_o	1.3.6.1.4.1.529.23.15.4.1.4	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_VcSwitchingVpi_Item_o	1.3.6.1.4.1.529.23.15.4.1.3	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_VcSwitchingVpi_Shelf_o	1.3.6.1.4.1.529.23.15.4.1.1	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_VcSwitchingVpi_Slot_o	1.3.6.1.4.1.529.23.15.4.1.2	INTEGER	read-only
INT e3AtmNetworkProfile_LineConfig_VpiVciRange	1.3.6.1.4.1.529.23.15.1.1.17	INTEGER	read-write	The E3 ATM valid VPI/VCI value range.
STR e3AtmNetworkProfile_Name	1.3.6.1.4.1.529.23.15.1.1.4	DisplayString	read-write	For future use. The current design does not use the name field but instead references E3-ATM lines by the physical address; we may in the future support referencing E3-ATM lines by name as well as by address. The name consists of a null terminated ascii string supplied by the user; it defaults to the ascii form of the E3-ATM line physical address.
INT e3AtmNetworkProfile_PhysicalAddress_ItemNumber	1.3.6.1.4.1.529.23.15.1.1.7	INTEGER	read-write	A number that specifies an addressable entity within the context of shelf and slot.
INT e3AtmNetworkProfile_PhysicalAddress_Shelf	1.3.6.1.4.1.529.23.15.1.1.5	INTEGER	read-write	The number of the shelf that the addressed physical device resides on.
INT e3AtmNetworkProfile_PhysicalAddress_Slot	1.3.6.1.4.1.529.23.15.1.1.6	INTEGER	read-write	The number of the slot that the addressed physical device resides on.
INT e3AtmNetworkProfile_Shelf_o	1.3.6.1.4.1.529.23.15.1.1.1	INTEGER	read-only
INT e3AtmNetworkProfile_Slot_o	1.3.6.1.4.1.529.23.15.1.1.2	INTEGER	read-only
INT e3AtmNetworkProfile_SparePhysicalAddress_ItemNumber	1.3.6.1.4.1.529.23.15.1.1.25	INTEGER	read-write	A number that specifies an addressable entity within the context of shelf and slot.
INT e3AtmNetworkProfile_SparePhysicalAddress_Shelf	1.3.6.1.4.1.529.23.15.1.1.23	INTEGER	read-write	The number of the shelf that the addressed physical device resides on.
INT e3AtmNetworkProfile_SparePhysicalAddress_Slot	1.3.6.1.4.1.529.23.15.1.1.24	INTEGER	read-write	The number of the slot that the addressed physical device resides on.
INT e3AtmNetworkProfile_SparingMode	1.3.6.1.4.1.529.23.15.1.1.26	INTEGER	read-write	Trunk port sparing operational mode for this port.
mibe3AtmNetworkProfile	1.3.6.1.4.1.529.23.15
mibe3AtmNetworkProfile_LineConfig_IncomingVCCsEntry	1.3.6.1.4.1.529.23.15.3.1		not-accessible	A mibe3AtmNetworkProfile__line_config__incomingVCCs entry containing objects that maps to the parameters of mibe3AtmNetworkProfile__line_config__incomingVCCs profile.
mibe3AtmNetworkProfile_LineConfig_IncomingVCCsTable	1.3.6.1.4.1.529.23.15.3		not-accessible	A list of mibe3AtmNetworkProfile__line_config__incomingVCCs profile entries.
mibe3AtmNetworkProfile_LineConfig_TrafficShapersEntry	1.3.6.1.4.1.529.23.15.2.1		not-accessible	A mibe3AtmNetworkProfile__line_config__traffic_shapers entry containing objects that maps to the parameters of mibe3AtmNetworkProfile__line_config__traffic_shapers profile.
mibe3AtmNetworkProfile_LineConfig_TrafficShapersTable	1.3.6.1.4.1.529.23.15.2		not-accessible	A list of mibe3AtmNetworkProfile__line_config__traffic_shapers profile entries.
mibe3AtmNetworkProfile_LineConfig_VcSwitchingVpiEntry	1.3.6.1.4.1.529.23.15.4.1		not-accessible	A mibe3AtmNetworkProfile__line_config__vc_switching_vpi entry containing objects that maps to the parameters of mibe3AtmNetworkProfile__line_config__vc_switching_vpi profile.
mibe3AtmNetworkProfile_LineConfig_VcSwitchingVpiTable	1.3.6.1.4.1.529.23.15.4		not-accessible	A list of mibe3AtmNetworkProfile__line_config__vc_switching_vpi profile entries.
mibe3AtmNetworkProfileEntry	1.3.6.1.4.1.529.23.15.1.1		not-accessible	A mibe3AtmNetworkProfile entry containing objects that maps to the parameters of mibe3AtmNetworkProfile profile.
mibe3AtmNetworkProfileTable	1.3.6.1.4.1.529.23.15.1		not-accessible	A list of mibe3AtmNetworkProfile profile entries.

RFC description

E3 ATM network profile configuration for Ascend equipment including physical addressing and line settings.

Start monitoring Ascend WAN edge/aggregation routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ASCEND-MIBE3ATMNET-MIB

What Is ASCEND-MIBE3ATMNET-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description