ARUBAWIRED-MVRP-MIB

All MIBs › ARUBAWIRED-MVRP-MIB

Organization: HPE/Aruba Networking Division

Last Updated: 2017-11-02

Category: Vendor: Aruba, Wireless and WLAN

Description: Aruba wired switch ArubaOS-CX MVRP dynamic VLAN registration protocol configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ARUBAWIRED-MVRP-MIB?

ARUBAWIRED-MVRP-MIB is a vendor-specific MIB for HPE Aruba VSX/CX wired switches, covering Multiple VLAN Registration Protocol (MVRP), the IEEE-standard mechanism switches use to dynamically propagate VLAN membership across a bridged network. It exposes configuration objects such as maximum VLAN limits and per-port registrar mode/timer settings, alongside per-port MVRP statistics and clear-stats controls. Its monitoring relevance is in protocol health and network configuration/software status rather than raw hardware: it lets an administrator confirm MVRP is registering VLANs correctly on each port, track periodic transmission status, and reset statistics counters to isolate a specific fault window. It depends on and interoperates with standard 802.1Q VLAN and IF-MIB interface indexing since ports are referenced via ifIndex. It is deployed in enterprise and campus networks using Aruba CX switches where dynamic VLAN propagation reduces manual trunk configuration across many switches. Engineers can download the ARUBAWIRED-MVRP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ARUBAWIRED-MVRP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Aruba CX/VSX wired switch (ArubaOS-CX)

Monitoring Examples

An administrator would poll arubaWiredMvrpPortConfigTable/Entry, keyed by arubaWiredMvrpPortConfigifIndex, to check arubaWiredMvrpPortConfigRegistrarMode and arubaWiredMvrpPortConfigPeriodicTransmissionStatus per port, and cross-reference arubaWiredMvrpPortStatsTable for registration counts. If arubaWiredMvrpMaxVlanLimit is being approached or a port's registrar mode is unexpectedly disabled, VLANs may fail to propagate to that port, causing intermittent connectivity for devices on a newly added VLAN. arubaWiredMvrpGlobalClearStats or arubaWiredMvrpPortStatsClearStats can be used to reset counters before re-testing a suspected registration issue.

What Can Be Monitored

MVRP registrar mode per port
MVRP periodic timer and transmission status
MVRP registration/deregistration statistics
maximum VLAN limit

Imported Objects

From ARUBAWIRED-NETWORKING-OID

wndFeatures

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From P-BRIDGE-MIB

EnabledStatus

From Q-BRIDGE-MIB

VlanId

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

TimeInterval
TruthValue

How to Use in IPNetwork Monitor

Example using arubaWiredMvrpPortStatsNewReceived OID:

Select an Aruba (HPE) ArubaOS-CX wired switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type arubaWiredMvrpPortStatsNewReceived into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of New messages received. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
arubaWiredMvrpMIB	1.3.6.1.4.1.47196.4.1.1.3.6			This is the MIB module related to HPE Aruba VSX feature
arubaWiredMvrpNotifications	1.3.6.1.4.1.47196.4.1.1.3.6.0
NTF arubaWiredMvrpVlanLimitReachedEvent	1.3.6.1.4.1.47196.4.1.1.3.6.0.1			The number of VLANs learned dynamically by MVRP has reached a configured limit. Notify the management entity with the number of VLANs learned dynamically by MVRP and the configured MVRP VLAN limit.
arubaWiredMvrpObjects	1.3.6.1.4.1.47196.4.1.1.3.6.1
arubaWiredMvrpConfig	1.3.6.1.4.1.47196.4.1.1.3.6.1.1
T/F arubaWiredMvrpGlobalClearStats	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.1	TruthValue	read-write	Defines the global clear statistics control for MVRP. True(1) indicates that MVRP should clear all statistic counters related to all ports in the system. A write operation of False(0) leads to a no operation and a GET request for this object always returns FALSE.
I32 arubaWiredMvrpMaxVlanLimit	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.2	Integer32	read-write	Defines the maximum number of dynamic VLANs that can be created on the system by MVRP. If the number of VLANs created by MVRP reaches this limit, the system will prevent MVRP from creating additional VLANs. A write operation for this object is not supported.
arubaWiredMvrpPortConfigTable	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.3		not-accessible	A table containing MVRP port configuration information.
arubaWiredMvrpPortConfigEntry	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.3.1		not-accessible	An MVRP port configuration entry.
NUM arubaWiredMvrpPortConfigifIndex	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.3.1.1	InterfaceIndex	not-accessible	The index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex.
INT arubaWiredMvrpPortConfigRegistrarMode	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.3.1.2	INTEGER	read-write	Defines the mode of operation of all the registrar state machines associated to the port. normal - Registration as well as de-registration of VLANs are allowed. fixed - The Registrar ignores all MRP messages and remains in IN state(Registered). NOTE: Forbidden Registration Mode will be managed by ieee8021QBridgeVlanForbiddenEgressPorts.
G32 arubaWiredMvrpPortConfigPeriodicTimer	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.3.1.3	Gauge32	read-write	Interval at which the Periodic transmission state machine of an MVRP instance generates transmission opportunities for the MVRP instance.
ENA arubaWiredMvrpPortConfigPeriodicTransmissionStatus	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.3.1.4	EnabledStatus	read-write	Used to enable or disable the Periodic transmission state machine of an MVRP instance.
T/F arubaWiredMvrpPortStatsClearStats	1.3.6.1.4.1.47196.4.1.1.3.6.1.1.3.1.5	TruthValue	read-write	Clear all statistics parameters corresponding to this port. True(1) indicates that MVRP will clear all statistic counters related to this port. A write operation of False(0) leads to a no operation and a GET request for this object always returns FALSE.
arubaWiredMvrpStats	1.3.6.1.4.1.47196.4.1.1.3.6.1.2
arubaWiredMvrpPortStatsTable	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1		not-accessible	A table containing MVRP port statistics information.
arubaWiredMvrpPortStatsEntry	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1		not-accessible	An MVRP port statistics entry.
NUM arubaWiredMvrpPortStatsifIndex	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.1	InterfaceIndex	not-accessible	The index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex.
C32 arubaWiredMvrpPortStatsNewReceivedEx	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.2	Counter32	read-only	The number of New messages received.
C32 arubaWiredMvrpPortStatsJoinInReceived	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.3	Counter32	read-only	The number of Join In messages received.
C32 arubaWiredMvrpPortStatsJoinEmptyReceived	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.4	Counter32	read-only	The number of Join Empty messages received.
C32 arubaWiredMvrpPortStatsLeaveReceived	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.5	Counter32	read-only	The number of Leave messages received.
C32 arubaWiredMvrpPortStatsInReceived	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.6	Counter32	read-only	The number of In messages received.
C32 arubaWiredMvrpPortStatsEmptyReceived	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.7	Counter32	read-only	The number of Empty messages received.
C32 arubaWiredMvrpPortStatsLeaveAllReceived	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.8	Counter32	read-only	The number of Leave all messages received.
C32 arubaWiredMvrpPortStatsNewTransmitted	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.9	Counter32	read-only	The number of New messages transmitted.
C32 arubaWiredMvrpPortStatsJoinInTransmitted	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.10	Counter32	read-only	The number of Join In messages transmitted.
C32 arubaWiredMvrpPortStatsJoinEmptyTransmitted	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.11	Counter32	read-only	The number of Join Empty messages transmitted.
C32 arubaWiredMvrpPortStatsLeaveTransmitted	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.12	Counter32	read-only	The number of Leave messages transmitted.
C32 arubaWiredMvrpPortStatsInTransmitted	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.13	Counter32	read-only	The number of In messages transmitted.
C32 arubaWiredMvrpPortStatsEmptyTransmitted	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.14	Counter32	read-only	The number of Empty messages transmitted.
C32 arubaWiredMvrpPortStatsLeaveAllTransmitted	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.15	Counter32	read-only	The number of Leave all messages transmitted.
C32 arubaWiredMvrpPortStatsTotalPDUReceived	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.16	Counter32	read-only	The total number of MVRP PDUs received.
C32 arubaWiredMvrpPortStatsTotalPDUTransmitted	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.17	Counter32	read-only	The total number of MVRP PDUs transmitted.
C32 arubaWiredMvrpPortStatsFramesDiscarded	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.1.1.18	Counter32	read-only	The number of Invalid messages received.
arubaWiredMvrpStateTable	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.2		not-accessible	A table that contains information about the MVRP state Machine(s) configuration.
arubaWiredMvrpStateEntry	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.2.1		not-accessible	A row in a table that contains the VLAN ID and port list.
VLA arubaWiredMvrpVlanId	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.2.1.1	VlanId	not-accessible	The VLAN ID to which this entry belongs.
NUM arubaWiredMvrpStateifIndex	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.2.1.2	InterfaceIndex	not-accessible	The index value that uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex.
INT arubaWiredMvrpApplicantState	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.2.1.3	INTEGER	read-only	This MIB provides the Applicant State Machine values of the MVRP enabled port as follows: 0 = aa, 1 = qa, 2 = la, 3 = vp, 4 = ap, 5 = qp, 6 = vo, 7 = ao, 8 = qo, 9 = lo, 10 = vn, 11 = an. The first letter indicates the state: V for Very anxious, A for Anxious, Q for Quiet, and L for Leaving. The second letter indicates the membership state: A for Active member, P for Passive member, O for Observer and N for New.
INT arubaWiredMvrpRegistrarState	1.3.6.1.4.1.47196.4.1.1.3.6.1.2.2.1.4	INTEGER	read-only	This MIB provides the Registrar state machine value for the MVRP enabled port as follows: 1 = registered, 2 = leaving, 3 = empty.
arubaWiredMvrpConformance	1.3.6.1.4.1.47196.4.1.1.3.6.3
arubaWiredMvrpCompliances	1.3.6.1.4.1.47196.4.1.1.3.6.3.1
arubaWiredMvrpCompliance	1.3.6.1.4.1.47196.4.1.1.3.6.3.1.1			Compliance statement for MVRP.
arubaWiredMvrpGroups	1.3.6.1.4.1.47196.4.1.1.3.6.3.2
arubaWiredMvrpBaseGroup	1.3.6.1.4.1.47196.4.1.1.3.6.3.2.1			Collection of objects for management of MVRP Base Group.
arubaWiredMvrpPortConfigGroup	1.3.6.1.4.1.47196.4.1.1.3.6.3.2.2			Collection of objects for management of MVRP Port Configuration Table.
arubaWiredMvrpPortStatsGroup	1.3.6.1.4.1.47196.4.1.1.3.6.3.2.3			Collection of objects for management of MVRP Statistics Table.
arubaWiredMvrpPortStateGroup	1.3.6.1.4.1.47196.4.1.1.3.6.3.2.4			Collection of objects to display Applicant and Registrar state machine of the ports.
arubaWiredMvrpNotifyGroup	1.3.6.1.4.1.47196.4.1.1.3.6.3.2.5			MVRP notification group.

RFC description

HPE Aruba Wired (formerly Aruba Networks) MIB for managing Multiple VLAN Registration Protocol (MVRP) on managed switches for dynamic VLAN registration.

Start monitoring Aruba (HPE) ArubaOS-CX wired switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ARUBAWIRED-MVRP-MIB