| OID symbolic | OID numeric | Type | Access | Description |
|---|
| a3Com | 1.3.6.1.4.1.43 | | | |
| switchingSystemsMibs | 1.3.6.1.4.1.43.29 | | | |
| a3ComSwitchingSystemsFddiMib | 1.3.6.1.4.1.43.29.10 | | | |
| NTF a3ComFddiSMTHoldCondition | 1.3.6.1.4.1.43.29.10.0.1 | | | Generated when fddiSMTHoldState (fddimibSMTHoldState) assumes the state holding-prm or holding-sec. This notification is a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF a3ComFddiSMTPeerWrapCondition | 1.3.6.1.4.1.43.29.10.0.2 | | | This condition is active when fddiSMTPeerWrapFlag (fddimibSMTPeerWrapFlag) is set. This notification is a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF a3ComFddiMACDuplicateAddressCondition | 1.3.6.1.4.1.43.29.10.0.3 | | | This condition is active when either fddiMACDA-Flag (fddimibMACDaFlag) or fddiMACUNDA-Flag (fddimibMACUnaDaFlag) is set. This event is handled as a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF a3ComFddiMACFrameErrorCondition | 1.3.6.1.4.1.43.29.10.0.4 | | | Generated when the fddiMACFrameErrorRatio (fddimibMACFrameErrorRatio) is greater than or equal to fddiMACFrameErrorThreshold (fddimibMACFrameErrorThreshold). This event is handled as a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF a3ComFddiMACNotCopiedCondition | 1.3.6.1.4.1.43.29.10.0.5 | | | Generated when the fddiMACNotCopiedRatio (fddimibMACNotCopiedRatio) is greater than or equal to the fddiMACNotCopiedThreshold (a3ComFddiMACNotCopiedThreshold). This event is handled as a Condition in the Status Report Protocol (see 7.2.7 and 8.3). |
| NTF a3ComFddiMACNeighborChangeEvent | 1.3.6.1.4.1.43.29.10.0.6 | | | Generated when a change in a MAC's upstream neighbor address or downstream neighbor address is detected. (see 7.2.7 and 8.3). |
| NTF a3ComFddiMACPathChangeEvent | 1.3.6.1.4.1.43.29.10.0.7 | | | This event is generated when the value of the fddiMACCurrentPath (fddimibMACCurrentPath) changes. This event shall be supressed if the value changes from isolated to local or local to isolated (see 7.2.7 and 8.3). |
| NTF a3ComFddiPORTLerCondition | 1.3.6.1.4.1.43.29.10.0.8 | | | This condition becomes active when the value of fddiPORTLer-Estimate (fddimibPORTLerEstimate) is less than or equal to fddiPORTLer-Alarm (fddimibPORTLerAlarm). This will be reported with the Status Report Frames (SRF) (see 7.2.7 and 8.3). |
| NTF a3ComFddiPORTUndesiredConnAttemptEvent | 1.3.6.1.4.1.43.29.10.0.9 | | | Generated when an undesired connection attempt has been made (see 5.2.4, 7.2.7, and 8.3). |
| NTF a3ComFddiPORTEBErrorCondition | 1.3.6.1.4.1.43.29.10.0.10 | | | Generated when the Elasticity Buffer Error-Ct (a3ComFddiPORTEBErrorCt) increments. This is handled as a condition in the Status Report Protocol. It is generated when an increment occurs in the station's sampling period (see 7.2.7 and 8.3). |
| NTF a3ComFddiPORTPathChangeEvent | 1.3.6.1.4.1.43.29.10.0.11 | | | This event is generated when the value of the fddiPORTCurrentPath (a3ComFddiPORTCurrentPath) changes. This event shall be surpressed if the value changes from isolated to local or local to isolated (see 7.2.7 and 8.3). |
| a3ComFddiSMT | 1.3.6.1.4.1.43.29.10.1 | | | |
| a3ComFddiSMTTable | 1.3.6.1.4.1.43.29.10.1.1 | | not-accessible | A list of optional SMT entries. The number of entries
shall not exceed the value of snmpFddiSMTNumber. |
| a3ComFddiSMTEntry | 1.3.6.1.4.1.43.29.10.1.1.1 | | not-accessible | An optional SMT entry containing information common to
a given optional SMT. |
| INT a3ComFddiSMTIndex | 1.3.6.1.4.1.43.29.10.1.1.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| OCT a3ComFddiSMTManufacturerOUI | 1.3.6.1.4.1.43.29.10.1.1.1.2 | OCTET STRING | read-only | The three octets of manufacturer data which make
up the manufacturerOUI component. |
| OCT a3ComFddiSMTManufacturerData | 1.3.6.1.4.1.43.29.10.1.1.1.3 | OCTET STRING | read-only | The 29 octets of manufacturer data which make up the
manufacturerData component. |
| INT a3ComFddiSMTHoldState | 1.3.6.1.4.1.43.29.10.1.1.1.4 | INTEGER | read-only | This variable indicates the current state of the
Hold function. The value 'not-holding' is the
default and initial value. The value must be set
to 'not-holding' as part of Active-Actions and
when the conditions causing 'holding-prm' or
'holding-sec' are no longer true. The value
'holding-prm' must be set when the condition
(notTR-Flag & not RE-Flag & (PC-LS=QLS | LEM-Fail
TNE>NS-Max | (not LS-Flag & TPC > T-Out))) is
satisfied in state PC8:ACTIVE for the A Port. The
value 'holding-sec' must be set when the condition
(notTR-Flag & not RE-Flag & (PC-LS=QLS | LEM-Fail
TNE>NS-Max | (not LS-Flag & TPC > T-Out))) is
satisfied in state PC8:ACTIVE for the B Port. |
| INT a3ComFddiSMTSetCount | 1.3.6.1.4.1.43.29.10.1.1.1.5 | INTEGER | read-only | This variable is composed of a count incremented
in response to a Set operation on the MIB, and the
time of the change, however only the count is
reported here (refer to ANSI SMT 8.4.1). |
| FDD a3ComFddiSMTLastSetStationId | 1.3.6.1.4.1.43.29.10.1.1.1.6 | FddiSMTStationIdType | read-only | The Station ID of the station that effected the last
change in the FDDI MIB. |
| a3ComFddiMAC | 1.3.6.1.4.1.43.29.10.2 | | | |
| a3ComFddiMACBridgeFunctionTable | 1.3.6.1.4.1.43.29.10.2.1 | | not-accessible | A list of MAC bridge function entries. |
| a3ComFddiMACBridgeFunctionEntry | 1.3.6.1.4.1.43.29.10.2.1.1 | | not-accessible | Bridge function information for a given MAC
within a given SMT. |
| INT a3ComFddiMACBridgeFunctionSMTIndex | 1.3.6.1.4.1.43.29.10.2.1.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT a3ComFddiMACBridgeFunctionMACIndex | 1.3.6.1.4.1.43.29.10.2.1.1.2 | INTEGER | read-only | Index variable for uniquely identifying the MAC
object instances. |
| INT a3ComFddiMACBridgeFunctions | 1.3.6.1.4.1.43.29.10.2.1.1.3 | INTEGER | read-only | Indicates the MAC's optional bridging functions.
The Value -1 is used to indicate that bridging is
not supported by this MAC.
The value is a sum. This value initially takes
the value zero, then for each function present, 2
raised to a power is added to the sum. The powers
are according to the following table:
Function Power
tb 0 -- Transparent bridging active
sr 1 -- Src routing active
srt 2 -- Src routing transparent active |
| a3ComFddiMACTPriTable | 1.3.6.1.4.1.43.29.10.2.2 | | not-accessible | A list of MAC T-Pri entries. |
| a3ComFddiMACTPriEntry | 1.3.6.1.4.1.43.29.10.2.2.1 | | not-accessible | A collection of T-Pri information for a given MAC within
a given SMT. |
| INT a3ComFddiMACTPriSMTIndex | 1.3.6.1.4.1.43.29.10.2.2.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT a3ComFddiMACTPriMACIndex | 1.3.6.1.4.1.43.29.10.2.2.1.2 | INTEGER | read-only | Index variable for uniquely identifying the MAC
object instances. |
| FDD a3ComFddiMACTPri0 | 1.3.6.1.4.1.43.29.10.2.2.1.3 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T-pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD a3ComFddiMACTPri1 | 1.3.6.1.4.1.43.29.10.2.2.1.4 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T-pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD a3ComFddiMACTPri2 | 1.3.6.1.4.1.43.29.10.2.2.1.5 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T-pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD a3ComFddiMACTPri3 | 1.3.6.1.4.1.43.29.10.2.2.1.6 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T-pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD a3ComFddiMACTPri4 | 1.3.6.1.4.1.43.29.10.2.2.1.7 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T-pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD a3ComFddiMACTPri5 | 1.3.6.1.4.1.43.29.10.2.2.1.8 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T-pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| FDD a3ComFddiMACTPri6 | 1.3.6.1.4.1.43.29.10.2.2.1.9 | FddiTimeNano | read-only | This attribute is an unsigned twos-complement T-pri
threshold as described in the MAC standard converted
to non-twos-complement form and reported in 1 ns units. |
| a3ComFddiPATH | 1.3.6.1.4.1.43.29.10.3 | | | |
| a3ComFddiPATHRingTable | 1.3.6.1.4.1.43.29.10.3.1 | | not-accessible | A list of PATH ring entries. |
| a3ComFddiPATHRingEntry | 1.3.6.1.4.1.43.29.10.3.1.1 | | not-accessible | Ring latency, trace status, and T-Rmode information for a
given PATH within a given SMT. |
| INT a3ComFddiPATHRingSMTIndex | 1.3.6.1.4.1.43.29.10.3.1.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT a3ComFddiPATHRingPATHIndex | 1.3.6.1.4.1.43.29.10.3.1.1.2 | INTEGER | read-only | Index variable for uniquely identifying the
primary, secondary and local PATH object
instances. Local PATH object instances are
represented with integer values 3 to 255. |
| FDD a3ComFddiPATHRingLatency | 1.3.6.1.4.1.43.29.10.3.1.1.3 | FddiTimeNano | read-write | Gives the total accumulated latency of the ring
associated with this path. May be measured directly
by the station or calculated by a management station.
Values of this object are reported in 1 ns units. |
| INT a3ComFddiPATHTraceStatus | 1.3.6.1.4.1.43.29.10.3.1.1.4 | INTEGER | read-only | This attribute indicates the current trace status of
the path.
The value is a sum which represents all of the trace
status information which applies. This value initially
takes the value zero, then for each condition which
applies, 2 raised to a power is added to the sum. the
powers are according to the following table:
TraceStatus Power
traceinitiated 0
tracepropragated 1
traceterminated 2
tracetimeout 3 |
| FDD a3ComFddiPATHT_Rmode | 1.3.6.1.4.1.43.29.10.3.1.1.5 | FddiTimeNano | read-write | Used by RMT to limit the duration of restricted dialogs on a path. This object is reported in 1 ns units. |
| a3ComFddiPATHSbaTable | 1.3.6.1.4.1.43.29.10.3.2 | | not-accessible | A list of PATH Sba entries. |
| a3ComFddiPATHSbaEntry | 1.3.6.1.4.1.43.29.10.3.2.1 | | not-accessible | Sba information for a given PATH within a given SMT. |
| INT a3ComFddiPATHSbaSMTIndex | 1.3.6.1.4.1.43.29.10.3.2.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT a3ComFddiPATHSbaPATHIndex | 1.3.6.1.4.1.43.29.10.3.2.1.2 | INTEGER | read-only | Index variable for uniquely identifying the
primary, secondary and local PATH object
instances. Local PATH object instances are
represented with integer values 3 to 255. |
| INT a3ComFddiPATHSbaPayload | 1.3.6.1.4.1.43.29.10.3.2.1.3 | INTEGER | read-write | The payload portion of the Synchronous Bandwidth
Allocation for thi path. This value represents the
maximum number of bytes of data allocated for
transmission per 125 microseconds. |
| INT a3ComFddiPATHSbaOverhead | 1.3.6.1.4.1.43.29.10.3.2.1.4 | INTEGER | read-write | The overhead portion of the Synchronous Bandwith
Allocation for this path. This value repersents the
maximum number of bytes overhead (token capture, frame
header, etc.) used pre negotiated Target Token Rotation
Time (T-neg). |
| INT a3ComFddiPATHSbaAvailable | 1.3.6.1.4.1.43.29.10.3.2.1.5 | INTEGER | read-write | This value is the maximum Synchronous Bandwith available
for a path in bytes per second. |
| a3ComFddiPORT | 1.3.6.1.4.1.43.29.10.4 | | | |
| a3ComFddiPORTTable | 1.3.6.1.4.1.43.29.10.4.1 | | not-accessible | A list of optional PORT entries. |
| a3ComFddiPORTEntry | 1.3.6.1.4.1.43.29.10.4.1.1 | | not-accessible | MAC loop time and EB error count information for a
given PORT within a given SMT. |
| INT a3ComFddiPORTSMTIndex | 1.3.6.1.4.1.43.29.10.4.1.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT a3ComFddiPORTIndex | 1.3.6.1.4.1.43.29.10.4.1.1.2 | INTEGER | read-only | Index variable for uniquely identifying the PORT
object instances. |
| FDD a3ComFddiPORTMACLoopTime | 1.3.6.1.4.1.43.29.10.4.1.1.3 | FddiTimeNano | read-write | This attribute controls the value used for T-Next(9)
(see 9.4.4.2.3). This object is reported in 1 ns
units. |
| CTR a3ComFddiPORTEBErrorCt | 1.3.6.1.4.1.43.29.10.4.1.1.4 | Counter | read-only | A count that should as closely as possible match the
times an Elasticity Buffer Error has occurred while in
active line state. |
| a3ComFddiPORTLSTable | 1.3.6.1.4.1.43.29.10.4.2 | | not-accessible | A list of optional PORT line state entries. |
| a3ComFddiPORTLSEntry | 1.3.6.1.4.1.43.29.10.4.2.1 | | not-accessible | Maintenance line state and PC line state information
for a given PORT within a given SMT. |
| INT a3ComFddiPORTLSSMTIndex | 1.3.6.1.4.1.43.29.10.4.2.1.1 | INTEGER | read-only | A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber. The
value for each SMT must remain constant at least
from one re-initialization of the entity's network
management system to the next re-initialization. |
| INT a3ComFddiPORTLSPORTIndex | 1.3.6.1.4.1.43.29.10.4.2.1.2 | INTEGER | read-only | Index variable for uniquely identifying the PORT
object instances. |
| INT a3ComFddiPORTMaintLS | 1.3.6.1.4.1.43.29.10.4.2.1.3 | INTEGER | read-write | The PORT Maintenance Line State specifies the line state
(Maint-LS) to be transmitted when the PCM state machine
for the port is in state PC9 Maint. |
| INT a3ComFddiPORTPCLS | 1.3.6.1.4.1.43.29.10.4.2.1.4 | INTEGER | read-only | This attribute indicates the line state (PC-LS) received
by the port. |
