ZXR10-TRACE-MIB

All MIBs › ZXR10-TRACE-MIB

Organization: ZTE Corporation.

Last Updated: 2015-04-03

Category: ZTE ZXR10 System Management

Description: Defines ZTE ZXR10 traceroute diagnostic operations for hop-by-hop path discovery and latency measurement.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZXR10-TRACE-MIB?

ZXR10-TRACE-MIB is a ZTE proprietary diagnostic module for ZXR10 routers and switches that models SNMP-driven traceroute operations, allowing a management station to trigger a traceroute from the device and retrieve the resulting hop-by-hop path. It exposes control objects to start a trace toward a target address and result objects listing each hop's address and measured round-trip latency. Rather than continuous hardware/software health counters, its monitoring value is diagnostic: an administrator uses it to verify network reachability and path latency from the device's perspective when troubleshooting routing or connectivity problems, complementing uptime and interface status data from other MIBs. It depends on standard SNMPv2-SMI conventions and is typically used alongside ZXR10 routing and interface MIBs during fault investigation. It is deployed in ZTE ZXR10 network environments as an on-demand diagnostic tool rather than a passive monitoring feed. Engineers can download the ZXR10-TRACE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZXR10-TRACE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE ZXR10 routers/switches

Monitoring Examples

No explicit object names were captured in sample_objects, but consistent with its purpose the module would expose a trace-control object to launch a traceroute and a trace-results table listing each hop's address, round-trip time, and status. An administrator troubleshooting a slow or unreachable destination would trigger a trace from the ZXR10 device and inspect the hop table for the point where latency spikes or responses stop.

What Can Be Monitored

traceroute hop addresses
per-hop round-trip latency
trace operation status
target reachability

Imported Objects

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From IPV6-TC

Ipv6Address

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

DateAndTime
DisplayString
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
zte	1.3.6.1.4.1.3902
zxr10	1.3.6.1.4.1.3902.3
trace	1.3.6.1.4.1.3902.3.318			ZTE TRACE MIB
zxr10LspTrace	1.3.6.1.4.1.3902.3.318.1
zxr10LspTraceCtlTable	1.3.6.1.4.1.3902.3.318.1.1		not-accessible	the description of lsp trace information.
zxr10LspTraceCtlEntry	1.3.6.1.4.1.3902.3.318.1.1.1		not-accessible	lsp trace control entry
I32 zxr10LspTraceCtlSerial	1.3.6.1.4.1.3902.3.318.1.1.1.1	Integer32	read-only	lsp trace control serial number
LSP zxr10LspTraceCtlTraceType	1.3.6.1.4.1.3902.3.318.1.1.1.2	LspTraceType	read-write	lsp trace type (0:ldp, 1:rsvpTe, 2:vccv, 3:v6ldp)
IP zxr10LspTraceCtlLdpPrefix	1.3.6.1.4.1.3902.3.318.1.1.1.3	IpAddress	read-write	ldp prefix
I32 zxr10LspTraceCtlLdpPrefixLength	1.3.6.1.4.1.3902.3.318.1.1.1.4	Integer32	read-write	ldp prefix length
STR zxr10LspTraceCtlTeTunnelIfName	1.3.6.1.4.1.3902.3.318.1.1.1.5	DisplayString	read-write	tunnel name
IP zxr10LspTraceCtlPwDestAddr	1.3.6.1.4.1.3902.3.318.1.1.1.6	IpAddress	read-write	pw peer address
U32 zxr10LspTraceCtlPwVcId	1.3.6.1.4.1.3902.3.318.1.1.1.7	Unsigned32	read-write	pw vcid
LSP zxr10LspTraceCtlIfOption	1.3.6.1.4.1.3902.3.318.1.1.1.9	LspTraceIfOption	read-write	if select option,default:none
I32 zxr10LspTraceCtlTimeOut	1.3.6.1.4.1.3902.3.318.1.1.1.10	Integer32	read-write	Timeout, default:3. The object is effective only when zxr10LspTraceCtlIfOption is option(1).
I32 zxr10LspTraceCtlTTL	1.3.6.1.4.1.3902.3.318.1.1.1.11	Integer32	read-write	TTL, default:30. The object is effective only when zxr10LspTraceCtlIfOption is option(1).
T/F zxr10LspTraceCtlTrapOncompletion	1.3.6.1.4.1.3902.3.318.1.1.1.12	TruthValue	read-write	Whether generate a notification when trace completed.
TRA zxr10LspTraceRosStatus	1.3.6.1.4.1.3902.3.318.1.1.1.13	TraceRosStatus	read-write	controls to start lsp trace
STR zxr10LspTraceEntryOwner	1.3.6.1.4.1.3902.3.318.1.1.1.14	DisplayString	read-write	Description of this entry's owner.
LSP zxr10LspTraceCtlPwType	1.3.6.1.4.1.3902.3.318.1.1.1.15	LspTracePwType	read-write	lsp pw type (0:etherVlan,1:ether)
STR zxr10LspTraceCtlPwName	1.3.6.1.4.1.3902.3.318.1.1.1.16	DisplayString	read-write	PW name
T/F zxr10LspTraceCtlMultiSegment	1.3.6.1.4.1.3902.3.318.1.1.1.17	TruthValue	read-write	Indicate if the pw is multi-segment or not.
ADR zxr10LspTraceCtlV6LdpPrefix	1.3.6.1.4.1.3902.3.318.1.1.1.18	Ipv6Address	read-write	IPv6 ldp prefix
I32 zxr10LspTraceCtlV6LdpPrefixLen	1.3.6.1.4.1.3902.3.318.1.1.1.19	Integer32	read-write	IPv6 ldp prefix length
STR zxr10LspTraceCtlOutInterface	1.3.6.1.4.1.3902.3.318.1.1.1.20	DisplayString	read-write	out-interface for tracing packets
INT zxr10LspTraceCtlLspType	1.3.6.1.4.1.3902.3.318.1.1.1.21	INTEGER	read-write	te-tunnel lsp type
IP zxr10LspTraceCtlSrcIpAddr	1.3.6.1.4.1.3902.3.318.1.1.1.22	IpAddress	read-write	Source IPv4 address for tracing
ADR zxr10LspTraceCtlV6SrcIpAddr	1.3.6.1.4.1.3902.3.318.1.1.1.23	Ipv6Address	read-write	Source IPv6 address for tracing
INT zxr10LspTraceCtlDownstrMapType	1.3.6.1.4.1.3902.3.318.1.1.1.24	INTEGER	read-write	Downstream mapping type - 0, Downstream Mapping in RFC4379 - 1, Downstream Detailed Mapping in RFC6424
INT zxr10LspTraceCtlReplyMode	1.3.6.1.4.1.3902.3.318.1.1.1.25	INTEGER	read-write	The reply mode by the receiving router receive an MPLS echo request
zxr10LspTraceResultsTable	1.3.6.1.4.1.3902.3.318.1.2		not-accessible	the description of lsp trace results information
zxr10LspTraceResultsEntry	1.3.6.1.4.1.3902.3.318.1.2.1		not-accessible	lsp trace result entry
I32 zxr10LspTraceResultsSerial	1.3.6.1.4.1.3902.3.318.1.2.1.1	Integer32	read-only	lsp trace result serial number
I32 zxr10LspTraceResultsCurHopCount	1.3.6.1.4.1.3902.3.318.1.2.1.2	Integer32	read-only	valid hops count
STR zxr10LspTraceResultsEntryOwner	1.3.6.1.4.1.3902.3.318.1.2.1.3	DisplayString	read-only	Description of this entry's owner.
zxr10LspTraceHopsTable	1.3.6.1.4.1.3902.3.318.1.3		not-accessible	the description of lsp trace hops information.
zxr10LspTraceHopsEntry	1.3.6.1.4.1.3902.3.318.1.3.1		not-accessible	lsp trace hops entry
I32 zxr10LspTraceHopsSerial	1.3.6.1.4.1.3902.3.318.1.3.1.1	Integer32	read-only	lsp trace hops serial number
I32 zxr10LspTraceHopsHopIndex	1.3.6.1.4.1.3902.3.318.1.3.1.2	Integer32	read-only	Hop index
TRA zxr10LspTraceHopsResultValid	1.3.6.1.4.1.3902.3.318.1.3.1.3	TraceHopsResult	read-only	Hop Result (0:valid,1:success,2:downstreamRouterButNotTarget, 3:requestNotTransmitted,4:timeout,5:unreachable)
HOP zxr10LspTraceHopsType	1.3.6.1.4.1.3902.3.318.1.3.1.4	HopType	read-only	Hop Type (0:Ingress,1:Downstream,2:Egress)
IP zxr10LspTraceHopsAddr	1.3.6.1.4.1.3902.3.318.1.3.1.5	IpAddress	read-only	Hop Address
I32 zxr10LspTraceHopsLabel	1.3.6.1.4.1.3902.3.318.1.3.1.6	Integer32	read-only	Hop Label
I32 zxr10LspTraceHopsMtu	1.3.6.1.4.1.3902.3.318.1.3.1.7	Integer32	read-only	Hop Mtu
I32 zxr10LspTraceHopsRtt	1.3.6.1.4.1.3902.3.318.1.3.1.8	Integer32	read-only	Hop Rtt
ADR zxr10LspTraceHopsV6Addr	1.3.6.1.4.1.3902.3.318.1.3.1.9	Ipv6Address	read-only	IPv6 hop address
lspTraceNotifications	1.3.6.1.4.1.3902.3.318.1.4
NTF lspTraceTrapResult	1.3.6.1.4.1.3902.3.318.1.4.1			The object will return a value while trace finish.
NTF lspTraceTrapHops	1.3.6.1.4.1.3902.3.318.1.4.2			The object will return a value while trace finish.
zxr10MacTrace	1.3.6.1.4.1.3902.3.318.2
zxr10MacTraceCtlTable	1.3.6.1.4.1.3902.3.318.2.1		not-accessible	the description of mac trace information.
zxr10MacTraceCtlEntry	1.3.6.1.4.1.3902.3.318.2.1.1		not-accessible	mac trace control entry
I32 zxr10MacTraceCtlSerial	1.3.6.1.4.1.3902.3.318.2.1.1.1	Integer32	read-only	mac trace control serial number
STR zxr10MacTraceCtlDestMac	1.3.6.1.4.1.3902.3.318.2.1.1.2	DisplayString	read-write	destination mac address
MAC zxr10MacTraceCtlIfPeOption	1.3.6.1.4.1.3902.3.318.2.1.1.3	MacTraceIfPeOption	read-write	if PE option (0:CE,1:PE)
I32 zxr10MacTraceCtlOutEtherIfIndex	1.3.6.1.4.1.3902.3.318.2.1.1.4	Integer32	read-write	index of out interface on CE
STR zxr10MacTraceCtlVfiName	1.3.6.1.4.1.3902.3.318.2.1.1.5	DisplayString	read-write	VFI name
IP zxr10MacTraceCtlPeerAddress	1.3.6.1.4.1.3902.3.318.2.1.1.6	IpAddress	read-write	Peer Address
I32 zxr10MacTraceCtlVlanCount	1.3.6.1.4.1.3902.3.318.2.1.1.7	Integer32	read-write	vlan count
I32 zxr10MacTraceCtlInternalVlanId	1.3.6.1.4.1.3902.3.318.2.1.1.8	Integer32	read-write	Internal VlanId
I32 zxr10MacTraceCtlExternalVlanId	1.3.6.1.4.1.3902.3.318.2.1.1.9	Integer32	read-write	External VlanId
T/F zxr10MacTraceCtlTrapOncompletion	1.3.6.1.4.1.3902.3.318.2.1.1.10	TruthValue	read-write	Whether generate a notification when trace completed.
TRA zxr10MacTraceCtlRosStatus	1.3.6.1.4.1.3902.3.318.2.1.1.11	TraceRosStatus	read-write	control to start mac trace
STR zxr10MacTraceCtlEntryOwner	1.3.6.1.4.1.3902.3.318.2.1.1.12	DisplayString	read-write	Description of this entry's owner.
zxr10MacTraceHopsTable	1.3.6.1.4.1.3902.3.318.2.2		not-accessible	the description of mac trace hops information.
zxr10MacTraceHopsEntry	1.3.6.1.4.1.3902.3.318.2.2.1		not-accessible	mac trace hops entry
I32 zxr10MacTraceHopsSerial	1.3.6.1.4.1.3902.3.318.2.2.1.1	Integer32	read-only	mac trace hops serial number
MAC zxr10MacTraceHopsResultValidHop0	1.3.6.1.4.1.3902.3.318.2.2.1.2	MactraceHopsResult	read-only	Hop0 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop0	1.3.6.1.4.1.3902.3.318.2.2.1.3	DisplayString	read-only	Hop0 Host Name
STR zxr10MacTraceHopsIfNameHop0	1.3.6.1.4.1.3902.3.318.2.2.1.4	DisplayString	read-only	Hop0 Interface Name
STR zxr10MacTraceHopsMacAddrHop0	1.3.6.1.4.1.3902.3.318.2.2.1.5	DisplayString	read-only	Hop0 Mac Address
MAC zxr10MacTraceHopsResultValidHop1	1.3.6.1.4.1.3902.3.318.2.2.1.6	MactraceHopsResult	read-only	Hop1 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop1	1.3.6.1.4.1.3902.3.318.2.2.1.7	DisplayString	read-only	Hop1 Host Name
STR zxr10MacTraceHopsIfNameHop1	1.3.6.1.4.1.3902.3.318.2.2.1.8	DisplayString	read-only	Hop1 Interface Name
STR zxr10MacTraceHopsMacAddrHop1	1.3.6.1.4.1.3902.3.318.2.2.1.9	DisplayString	read-only	Hop1 Mac Address
MAC zxr10MacTraceHopsResultValidHop2	1.3.6.1.4.1.3902.3.318.2.2.1.10	MactraceHopsResult	read-only	Hop2 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop2	1.3.6.1.4.1.3902.3.318.2.2.1.11	DisplayString	read-only	Hop2 Host Name
STR zxr10MacTraceHopsIfNameHop2	1.3.6.1.4.1.3902.3.318.2.2.1.12	DisplayString	read-only	Hop2 Interface Name
STR zxr10MacTraceHopsMacAddrHop2	1.3.6.1.4.1.3902.3.318.2.2.1.13	DisplayString	read-only	Hop2 Mac Address
MAC zxr10MacTraceHopsResultValidHop3	1.3.6.1.4.1.3902.3.318.2.2.1.14	MactraceHopsResult	read-only	Hop3 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop3	1.3.6.1.4.1.3902.3.318.2.2.1.15	DisplayString	read-only	Hop3 Host Name
STR zxr10MacTraceHopsIfNameHop3	1.3.6.1.4.1.3902.3.318.2.2.1.16	DisplayString	read-only	Hop3 Interface Name
STR zxr10MacTraceHopsMacAddrHop3	1.3.6.1.4.1.3902.3.318.2.2.1.17	DisplayString	read-only	Hop3 Mac Address
MAC zxr10MacTraceHopsResultValidHop4	1.3.6.1.4.1.3902.3.318.2.2.1.18	MactraceHopsResult	read-only	Hop4 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop4	1.3.6.1.4.1.3902.3.318.2.2.1.19	DisplayString	read-only	Hop4 Host Name
STR zxr10MacTraceHopsIfNameHop4	1.3.6.1.4.1.3902.3.318.2.2.1.20	DisplayString	read-only	Hop4 Interface Name
STR zxr10MacTraceHopsMacAddrHop4	1.3.6.1.4.1.3902.3.318.2.2.1.21	DisplayString	read-only	Hop4 Mac Address
MAC zxr10MacTraceHopsResultValidHop5	1.3.6.1.4.1.3902.3.318.2.2.1.22	MactraceHopsResult	read-only	Hop5 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop5	1.3.6.1.4.1.3902.3.318.2.2.1.23	DisplayString	read-only	Hop5 Host Name
STR zxr10MacTraceHopsIfNameHop5	1.3.6.1.4.1.3902.3.318.2.2.1.24	DisplayString	read-only	Hop5 Interface Name
STR zxr10MacTraceHopsMacAddrHop5	1.3.6.1.4.1.3902.3.318.2.2.1.25	DisplayString	read-only	Hop5 Mac Address
MAC zxr10MacTraceHopsResultValidHop6	1.3.6.1.4.1.3902.3.318.2.2.1.26	MactraceHopsResult	read-only	Hop6 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop6	1.3.6.1.4.1.3902.3.318.2.2.1.27	DisplayString	read-only	Hop6 Host Name
STR zxr10MacTraceHopsIfNameHop6	1.3.6.1.4.1.3902.3.318.2.2.1.28	DisplayString	read-only	Hop6 Interface Name
STR zxr10MacTraceHopsMacAddrHop6	1.3.6.1.4.1.3902.3.318.2.2.1.29	DisplayString	read-only	Hop6 Mac Address
MAC zxr10MacTraceHopsResultValidHop7	1.3.6.1.4.1.3902.3.318.2.2.1.30	MactraceHopsResult	read-only	Hop7 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop7	1.3.6.1.4.1.3902.3.318.2.2.1.31	DisplayString	read-only	Hop7 Host Name
STR zxr10MacTraceHopsIfNameHop7	1.3.6.1.4.1.3902.3.318.2.2.1.32	DisplayString	read-only	Hop7 Interface Name
STR zxr10MacTraceHopsMacAddrHop7	1.3.6.1.4.1.3902.3.318.2.2.1.33	DisplayString	read-only	Hop7 Mac Address
MAC zxr10MacTraceHopsResultValidHop8	1.3.6.1.4.1.3902.3.318.2.2.1.34	MactraceHopsResult	read-only	Hop8 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop8	1.3.6.1.4.1.3902.3.318.2.2.1.35	DisplayString	read-only	Hop8 Host Name
STR zxr10MacTraceHopsIfNameHop8	1.3.6.1.4.1.3902.3.318.2.2.1.36	DisplayString	read-only	Hop8 Interface Name
STR zxr10MacTraceHopsMacAddrHop8	1.3.6.1.4.1.3902.3.318.2.2.1.37	DisplayString	read-only	Hop8 Mac Address
MAC zxr10MacTraceHopsResultValidHop9	1.3.6.1.4.1.3902.3.318.2.2.1.38	MactraceHopsResult	read-only	Hop9 Result (0:valid,1:success)
STR zxr10MacTraceHopsHostNameHop9	1.3.6.1.4.1.3902.3.318.2.2.1.39	DisplayString	read-only	Hop9 Host Name
STR zxr10MacTraceHopsIfNameHop9	1.3.6.1.4.1.3902.3.318.2.2.1.40	DisplayString	read-only	Hop9 Interface Name
STR zxr10MacTraceHopsMacAddrHop9	1.3.6.1.4.1.3902.3.318.2.2.1.41	DisplayString	read-only	Hop9 Mac Address
STR zxr10MacTraceHopsEntryOwner	1.3.6.1.4.1.3902.3.318.2.2.1.42	DisplayString	read-only	Description of this entry's owner.
macTraceNotifications	1.3.6.1.4.1.3902.3.318.2.4
NTF macTraceTrapResult	1.3.6.1.4.1.3902.3.318.2.4.1			Generated when trace finished.
zxr10TraceRoute	1.3.6.1.4.1.3902.3.318.3
zxr10TraceRouteObjects	1.3.6.1.4.1.3902.3.318.3.1
zxr10TraceRouteCtlTable	1.3.6.1.4.1.3902.3.318.3.1.1		not-accessible	Defines the Remote Operations Traceroute Control Table for providing the capability of invoking traceroute from a remote host. The results of traceroute operations can be stored in the zxr10TraceRouteResultsTable, and the zxr10TraceRouteHopsTable.
zxr10TraceRouteCtlEntry	1.3.6.1.4.1.3902.3.318.3.1.1.1		not-accessible	Defines an entry in the zxr10TraceRouteCtlTable. The index element, zxr10TraceRouteCtlSerial, is of type Integer32, limited to 100 entries.
I32 zxr10TraceRouteCtlSerial	1.3.6.1.4.1.3902.3.318.3.1.1.1.1	Integer32	not-accessible	Traceroute control serial number.
INT zxr10TraceRouteCtlTraceType	1.3.6.1.4.1.3902.3.318.3.1.1.1.2	INTEGER	read-create	The type of a traceroute destination. 1: IP address, uses zxr10TraceRouteCtlTgtAddr 2: domain name, uses zxr10TraceRouteCtlDomainName
IPt zxr10TraceRouteCtlIpAddrType	1.3.6.1.4.1.3902.3.318.3.1.1.1.3	InetAddressType	read-create	Specifies the IP address type for the traceroute request, including zxr10TraceRouteCtlDstAddr and zxr10TraceRouteCtlSrcAddr.
IP zxr10TraceRouteCtlTgtAddr	1.3.6.1.4.1.3902.3.318.3.1.1.1.4	InetAddress	read-create	Specifies the host address used on the traceroute request at the remote host.
STR zxr10TraceRouteCtlDomainName	1.3.6.1.4.1.3902.3.318.3.1.1.1.5	DisplayString	read-create	The name of a traceroute domain.
INT zxr10TraceRouteCtlVrfType	1.3.6.1.4.1.3902.3.318.3.1.1.1.6	INTEGER	read-create	Controls the VRF type of traceroute test. 1: not vrf 2: normal vrf, uses zxr10TraceRouteCtlVrfName 3: dcn vrf, the vrf name is ?_dcn
STR zxr10TraceRouteCtlVrfName	1.3.6.1.4.1.3902.3.318.3.1.1.1.7	DisplayString	read-create	VRF name.
U32 zxr10TraceRouteCtlMaxTtl	1.3.6.1.4.1.3902.3.318.3.1.1.1.8	Unsigned32	read-create	Specifies the maximum time-to-live value.
U32 zxr10TraceRouteCtlTimeOut	1.3.6.1.4.1.3902.3.318.3.1.1.1.9	Unsigned32	read-create	Specifies the time-out value, in seconds, for a traceroute request.
U32 zxr10TraceRouteCtlProbPerHop	1.3.6.1.4.1.3902.3.318.3.1.1.1.10	Unsigned32	read-create	Specifies the number of times to reissue a traceroute request with the same time-to-live (TTL) value.
IP zxr10TraceRouteCtlSrcAddr	1.3.6.1.4.1.3902.3.318.3.1.1.1.11	InetAddress	read-create	Use the specified IP address (which must be given as an IP number, not a hostname) as the source address in outgoing probe packets. On hosts with more than one IP address, this option can be used to select the address to be used. If the IP address is not one of this machine's interface addresses, an error is returned, and nothing is sent. A zero-length octet string value for this object disables source address specification.
T/F zxr10TraceRouteCtlGenHopEntry	1.3.6.1.4.1.3902.3.318.3.1.1.1.12	TruthValue	read-create	The current path for a traceroute test is kept in the zxr10TraceRouteHopsTable on a per-hop basis when the value of this object is true(1).
INT zxr10TraceRouteCtlRowStatus	1.3.6.1.4.1.3902.3.318.3.1.1.1.13	INTEGER	read-create	This object allows to start tracing or destroy entries in the zxr10TraceRouteCtlTable.
U32 zxr10TraceRouteCtlDataSize	1.3.6.1.4.1.3902.3.318.3.1.1.1.14	Unsigned32	read-create	Specifies the size of the data portion of a traceroute request, in octets. The value for this object includes IP header size and UDP header size.
zxr10TraceRouteResultsTable	1.3.6.1.4.1.3902.3.318.3.1.2		not-accessible	Defines the Remote Operations Traceroute Results Table for keeping track of the status of a zxr10TraceRouteCtlEntry. An entry is added to the zxr10TraceRouteResultsTable when an zxr10TraceRouteCtlEntry is started. An entry is removed from the zxr10TraceRouteResultsTable when its corresponding zxr10TraceRouteCtlEntry is deleted.
zxr10TraceRouteResultsEntry	1.3.6.1.4.1.3902.3.318.3.1.2.1		not-accessible	Defines an entry in the zxr10TraceRouteResultsTable. The zxr10TraceRouteResultsTable has the same indexing as the zxr10TraceRouteCtlTable.
U32 zxr10TraceRouteResCurHopCount	1.3.6.1.4.1.3902.3.318.3.1.2.1.1	Unsigned32	read-only	Reflects the current TTL value (from 1 to 255) for a remote traceroute operation. Maximum TTL value is determined by zxr10TraceRouteCtlMaxTtl.
U32 zxr10TraceRouteResCurProbCount	1.3.6.1.4.1.3902.3.318.3.1.2.1.2	Unsigned32	read-only	Reflects the current probe count (1..10) for a remote traceroute operation. The maximum probe count is determined by zxr10TraceRouteCtlProbPerHop.
IPt zxr10TraceRouteResIpTgtAddrType	1.3.6.1.4.1.3902.3.318.3.1.2.1.3	InetAddressType	read-only	This object indicates the type of address stored in the corresponding zxr10TraceRouteResIpTgtAddr object.
IP zxr10TraceRouteResIpTgtAddr	1.3.6.1.4.1.3902.3.318.3.1.2.1.4	InetAddress	read-only	This object reports the IP address associated with a zxr10TraceRouteCtlTgtAddr value when the destination address is specified as a DNS name. The value of this object should be a zero-length octet string when a DNS name is not specified or when a specified DNS name fails to resolve.
U32 zxr10TraceRouteResTestAttempts	1.3.6.1.4.1.3902.3.318.3.1.2.1.5	Unsigned32	read-only	The current number of attempts to determine a path to a target. The value of this object MUST be started at 0.
U32 zxr10TraceRouteResTestSuccesses	1.3.6.1.4.1.3902.3.318.3.1.2.1.6	Unsigned32	read-only	The current number of attempts to determine a path to a target that have succeeded. The value of this object MUST be reported as 0 when no attempts have succeeded.
DAT zxr10TraceRouteResLastGoodPath	1.3.6.1.4.1.3902.3.318.3.1.2.1.7	DateAndTime	read-only	The date and time when the last complete path was determined. A path is complete if responses were received or timeout occurred for each hop on the path.
zxr10TraceRouteHopsTable	1.3.6.1.4.1.3902.3.318.3.1.4		not-accessible	Defines the Remote Operations Traceroute Hop Table for keeping track of the results of traceroute tests on a per-hop basis.
zxr10TraceRouteHopsEntry	1.3.6.1.4.1.3902.3.318.3.1.4.1		not-accessible	Defines an entry in the zxr10TraceRouteHopsTable. The index elements identify the zxr10TraceRouteCtlEntry that a zxr10TraceRouteHopsEntry belongs to.
I32 zxr10TraceRouteHopsIndex	1.3.6.1.4.1.3902.3.318.3.1.4.1.1	Integer32	not-accessible	Specifies the hop index for a traceroute hop.
IPt zxr10TraceRouteHopsIpTgtAddrType	1.3.6.1.4.1.3902.3.318.3.1.4.1.2	InetAddressType	read-only	This object indicates the type of address stored in the corresponding zxr10TraceRouteHopsIpTgtAddr object.
IP zxr10TraceRouteHopsIpTgtAddr	1.3.6.1.4.1.3902.3.318.3.1.4.1.3	InetAddress	read-only	This object reports the IP address associated with the hop. A value for this object should be reported as a numeric IP address, not as a DNS name.
U32 zxr10TraceRouteHopsMinRtt	1.3.6.1.4.1.3902.3.318.3.1.4.1.4	Unsigned32	read-only	The minimum traceroute round-trip-time (RTT) received for this hop. A value of 0 for this object implies that no RTT has been received.
U32 zxr10TraceRouteHopsMaxRtt	1.3.6.1.4.1.3902.3.318.3.1.4.1.5	Unsigned32	read-only	The maximum traceroute round-trip-time (RTT) received for this hop. A value of 0 for this object implies that no RTT has been received.
U32 zxr10TraceRouteHopsAverageRtt	1.3.6.1.4.1.3902.3.318.3.1.4.1.6	Unsigned32	read-only	The current average traceroute round-trip-time (RTT) for this hop.
U32 zxr10TraceRouteHopsRttSumOfSquar	1.3.6.1.4.1.3902.3.318.3.1.4.1.7	Unsigned32	read-only	This object contains the sum of the squares of all round-trip-times received for this hop. Its purpose is to enable standard deviation calculation.
U32 zxr10TraceRouteHopsSentProbs	1.3.6.1.4.1.3902.3.318.3.1.4.1.8	Unsigned32	read-only	The value of this object reflects the number of probes sent for this hop during this traceroute test. The value of this object should start at 0.
U32 zxr10TraceRouteHopsProbResponses	1.3.6.1.4.1.3902.3.318.3.1.4.1.9	Unsigned32	read-only	Number of responses received for this hop during this traceroute test. This value of this object should start at 0.
DAT zxr10TraceRouteHopsLastGoodProb	1.3.6.1.4.1.3902.3.318.3.1.4.1.10	DateAndTime	read-only	Date and time at which the last response was received for a probe for this hop during this traceroute test.

RFC description

Provides traceroute functionality for both IP routes and MPLS LSP paths with timeout and hop-by-hop result tracking.

Start monitoring ZTE ZXR10 routers/switches (SNMP-driven traceroute hop/round-trip-latency status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZXR10-TRACE-MIB

What Is ZXR10-TRACE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description