Wellfleet-SYS-SVC-MIB

All MIBs › Wellfleet-SYS-SVC-MIB

Category: Wellfleet BayNetworks System Management

Description: Manages Wellfleet system services configuration including process states and service startup parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-SYS-SVC-MIB?

Wellfleet-SYS-SVC-MIB is a Wellfleet (Bay Networks) enterprise MIB built from the wfNetBootGroup branch of Wellfleet-COMMON-MIB, and despite its 'system services' name the module is entirely about network boot (netboot) configuration rather than process states or service startup parameters. Global scalars enable or disable booting the executable image and the configuration file over the network versus from local storage (wfNetbootImage, wfNetbootConfig) and specify the remote server address and file pathnames (wfNetbootServerAddress, wfNetbootImageName, wfNetbootConfigName); a parallel wfNetbootCurrGroup exposes the values currently latched in non-volatile RAM. Per-interface netboot parameters — IP address/mask, next-hop router, protocol mask, enable/disable, and (for AN-series routers) Token Ring speed or B-channel/DSU-CSU rate — are captured in wfNetbootCfgTable and its current-value counterpart wfNetbootCurrTable, both indexed by slot and connector. So the actual monitoring value here is confirming which image/config file and remote server a given Wellfleet router slot will netboot from, not general service health, and it is deployed on Wellfleet/Bay Networks routing platforms (including AN-series routers), for which the Wellfleet-SYS-SVC-MIB download provides the full object definitions.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-SYS-SVC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet / Bay Networks routers (including AN-series)

Monitoring Examples

An operator compares wfNetbootImageName against wfNetbootImageNameCurr for a given slot/connector to confirm a configuration change to the netboot image path has actually taken effect in NVRAM; a mismatch between the two indicates the new path was set but the router has not yet been rebooted to pick it up.

What Can Be Monitored

netboot image/config enable state (configured and current)
netboot remote server address
netboot image and config file pathnames
per-slot/connector netboot IP address and next-hop
per-slot/connector netboot enable/disable and link-speed parameters

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfNetBootGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfNetbootCfgGroup	1.3.6.1.4.1.18.3.3.2.10.1
INT wfNetbootImage	1.3.6.1.4.1.18.3.3.2.10.1.1	INTEGER	read-write	Enables booting of an executable image over the network. If disabled, then the image will be read from a local file system.
INT wfNetbootConfig	1.3.6.1.4.1.18.3.3.2.10.1.2	INTEGER	read-write	Enables booting of a configuration file over the network. If disabled, then the config will be read from a local file system.
IP wfNetbootServerAddress	1.3.6.1.4.1.18.3.3.2.10.1.3	IpAddress	read-write	IP address of remote server.
STR wfNetbootImageName	1.3.6.1.4.1.18.3.3.2.10.1.4	DisplayString	read-write	Pathname of image file on remote server.
STR wfNetbootConfigName	1.3.6.1.4.1.18.3.3.2.10.1.5	DisplayString	read-write	Pathname of configuration file on remote server.
INT wfNetbootCfgDelete	1.3.6.1.4.1.18.3.3.2.10.1.6	INTEGER	read-write	create/delete parameter, dflt = created
wfNetbootCurrGroup	1.3.6.1.4.1.18.3.3.2.10.2
INT wfNetbootImageCurr	1.3.6.1.4.1.18.3.3.2.10.2.1	INTEGER	read-only	Current value of Netboot image flag in Non-Volatile RAM.
INT wfNetbootConfigCurr	1.3.6.1.4.1.18.3.3.2.10.2.2	INTEGER	read-only	Current value of Netboot config flag in Non-Volatile RAM.
IP wfNetbootServerAddressCurr	1.3.6.1.4.1.18.3.3.2.10.2.3	IpAddress	read-only	IP address of remote server.
STR wfNetbootImageNameCurr	1.3.6.1.4.1.18.3.3.2.10.2.4	DisplayString	read-only	Pathname of image file on remote server.
STR wfNetbootConfigNameCurr	1.3.6.1.4.1.18.3.3.2.10.2.5	DisplayString	read-only	Pathname of configuration file on remote server.
wfNetbootCfgTable	1.3.6.1.4.1.18.3.3.2.10.3		not-accessible	A Table of Interface-specific Netboot Configuration Parameters
wfNetbootCfgEntry	1.3.6.1.4.1.18.3.3.2.10.3.1		not-accessible	Values of a particular interface's configuration parameters.
INT wfNetbootDelete	1.3.6.1.4.1.18.3.3.2.10.3.1.1	INTEGER	read-write	create/delete parameter, dflt = created Deleteing this instance will set the corresponding NOVRAM values to the default settings.
INT wfNetbootSlot	1.3.6.1.4.1.18.3.3.2.10.3.1.2	INTEGER	read-only	instance ID Slot, filled in by driver
INT wfNetbootConnector	1.3.6.1.4.1.18.3.3.2.10.3.1.3	INTEGER	read-only	Unique number which identifies the interface for which the following parameters are configured.
IP wfNetbootIpAddr	1.3.6.1.4.1.18.3.3.2.10.3.1.4	IpAddress	read-write	IP address to use on this interface
IP wfNetbootIpMask	1.3.6.1.4.1.18.3.3.2.10.3.1.5	IpAddress	read-write	IP address mask to use on this interface
IP wfNetbootNextHop	1.3.6.1.4.1.18.3.3.2.10.3.1.6	IpAddress	read-write	IP address of the next hop router connected to this interface. This value is used to auto-configure a static route for Network Boot.
INT wfNetbootProtoMask	1.3.6.1.4.1.18.3.3.2.10.3.1.7	INTEGER	read-write	Bit Mask indicating a non-default protocol is being used on this interface.
INT wfNetbootDisable	1.3.6.1.4.1.18.3.3.2.10.3.1.8	INTEGER	read-write	Enable or disable the interface for Netbooting.
STR wfNetbootConnName	1.3.6.1.4.1.18.3.3.2.10.3.1.9	DisplayString	read-only	Connector name.
INT wfNetbootTokenRingSpeed	1.3.6.1.4.1.18.3.3.2.10.3.1.10	INTEGER	read-write	Speed of the Token Ring interface for Netbooting.
INT wfNetbootBchanRate	1.3.6.1.4.1.18.3.3.2.10.3.1.11	INTEGER	read-write	Speed B Channel for Netbooting. AN 200 Only
INT wfNetbootDsuCsuOpMode	1.3.6.1.4.1.18.3.3.2.10.3.1.12	INTEGER	read-write	Dsu/Csu interface speed for Netbooting
wfNetbootCurrTable	1.3.6.1.4.1.18.3.3.2.10.4		not-accessible	A Table of current values for Interface-specific Netboot Parameters
wfNetbootCurrEntry	1.3.6.1.4.1.18.3.3.2.10.4.1		not-accessible	Values of a particular interface's current configuration parameters.
INT wfNetbootCurrSlot	1.3.6.1.4.1.18.3.3.2.10.4.1.1	INTEGER	read-only	instance ID Slot, filled in by driver
INT wfNetbootCurrConnector	1.3.6.1.4.1.18.3.3.2.10.4.1.2	INTEGER	read-only	Unique number which identifies the interface for which the following parameters are configured.
IP wfNetbootCurrIpAddr	1.3.6.1.4.1.18.3.3.2.10.4.1.3	IpAddress	read-only	IP address to use on this interface
IP wfNetbootCurrIpMask	1.3.6.1.4.1.18.3.3.2.10.4.1.4	IpAddress	read-only	IP address mask to use on this interface
IP wfNetbootCurrNextHop	1.3.6.1.4.1.18.3.3.2.10.4.1.5	IpAddress	read-only	IP address of the next hop router connected to this interface. This value is used to auto-configure a static route for Network Boot.
INT wfNetbootCurrProtoMask	1.3.6.1.4.1.18.3.3.2.10.4.1.6	INTEGER	read-only	Bit Mask indicating a non-default protocol is being used on this interface.
INT wfNetbootCurrDisable	1.3.6.1.4.1.18.3.3.2.10.4.1.7	INTEGER	read-only	Enable or disable the interface for Netbooting.
STR wfNetbootCurrConnName	1.3.6.1.4.1.18.3.3.2.10.4.1.8	DisplayString	read-only	Connector name.
INT wfNetbootCurrTokenRingSpeed	1.3.6.1.4.1.18.3.3.2.10.4.1.9	INTEGER	read-only	Speed of the Token Ring interface for Netbooting.
INT wfNetbootCurrBchanRate	1.3.6.1.4.1.18.3.3.2.10.4.1.10	INTEGER	read-write	Speed B Channel for Netbooting. AN 200 Only
INT wfNetbootCurrDsuCsuOpMode	1.3.6.1.4.1.18.3.3.2.10.4.1.11	INTEGER	read-write	Dsu/Csu interface speed for Netbooting

RFC description

Wellfleet network boot configuration for remote image and configuration file loading.

Start monitoring Wellfleet / Bay Networks routers, including AN-series (netboot image/config-server config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-SYS-SVC-MIB

What Is Wellfleet-SYS-SVC-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description