Wellfleet-OSI-MIB

All MIBs › Wellfleet-OSI-MIB

Category: Wellfleet BayNetworks Routing Protocols

Description: Monitors Wellfleet OSI protocol stack parameters, CLNP routing, and IS-IS adjacency statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-OSI-MIB?

Wellfleet-OSI-MIB is a vendor MIB from Wellfleet Communications (later Bay Networks/Nortel) covering the OSI protocol stack on Wellfleet routers, including CLNP (Connectionless Network Protocol) routing and the IS-IS interior gateway routing protocol used in OSI-based networks. It exposes configuration data for CLNP addressing and IS-IS routing parameters, along with status objects for IS-IS adjacency state and related routing statistics. Its monitoring focus is on routing protocol software status: an operator checks IS-IS adjacency state to confirm neighboring routers remain correctly adjacent and watches CLNP routing statistics for anomalies indicating a topology or configuration problem in the OSI routing domain. It implements the ISO/OSI CLNP and IS-IS standards, so its addressing and adjacency model closely follows those specifications rather than an IETF MIB. It is typically deployed on legacy Wellfleet/Bay Networks routers in telecom and government networks that historically ran OSI-based routing alongside or instead of IP. Engineers can download the Wellfleet-OSI-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-OSI-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet/Bay Networks routers
legacy OSI/CLNP routing infrastructure

Monitoring Examples

An administrator would poll the IS-IS adjacency status objects to confirm a router maintains full adjacency with its OSI routing neighbors, and an adjacency reported down or flapping would reveal a link failure or IS-IS parameter mismatch (such as area address or timer settings) disrupting CLNP routing in that domain. No sample objects were listed in the source excerpt, so specific table/object names are inferred from standard CLNP/IS-IS adjacency concepts rather than taken verbatim from the MIB.

What Can Be Monitored

IS-IS adjacency state
CLNP addressing configuration
routing protocol statistics
area/topology configuration

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
Opaque

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfOsiGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfOsi	1.3.6.1.4.1.18.3.5.6.1
INT wfOsiDelete	1.3.6.1.4.1.18.3.5.6.1.1	INTEGER	read-write	This value determines whether OSI is configured on this slot.
INT wfOsiDisable	1.3.6.1.4.1.18.3.5.6.1.2	INTEGER	read-write	This value determines whether OSI is to startup.
INT wfOsiState	1.3.6.1.4.1.18.3.5.6.1.3	INTEGER	read-only	This value determines whether OSI is to startup.
STR wfOsiIsisVersion	1.3.6.1.4.1.18.3.5.6.1.4	DisplayString	read-only	This read-only parameter identifies the version number of the IS-IS protocol to which this node conforms to.
INT wfOsiRouterType	1.3.6.1.4.1.18.3.5.6.1.5	INTEGER	read-write	This value determines whether this system is an L1-only router or L1-L2 IS.
OCT wfOsiRouterId	1.3.6.1.4.1.18.3.5.6.1.6	OCTET STRING	read-write	This value contains the system ID of this Intermediate System. If no value is entered by the user, Site Manager should supply a 6-byte value that will be unique (a MAC address would work).
INT wfOsiLoadBal	1.3.6.1.4.1.18.3.5.6.1.7	INTEGER	read-write	This Boolean defines whether or not we are doing load balancing over multiple paths.
INT wfOsiMaxAreas	1.3.6.1.4.1.18.3.5.6.1.8	INTEGER	read-write	This value defines the maximum allowable number of areas addresses for the domain that this router exists in.
INT wfOsiMaxEs	1.3.6.1.4.1.18.3.5.6.1.9	INTEGER	read-write	This value defines the maximum allowable number of End Systems for the area that this router exists in.
INT wfOsiMaxL1Is	1.3.6.1.4.1.18.3.5.6.1.10	INTEGER	read-write	This value defines the maximum allowable number of L1 Intermediate Systems for the area that this router exists in.
INT wfOsiMaxL2Is	1.3.6.1.4.1.18.3.5.6.1.11	INTEGER	read-write	This value defines the maximum allowable number of L2 Intermediate Systems for the domain that this router exists in.
INT wfOsiMaxExtAddr	1.3.6.1.4.1.18.3.5.6.1.12	INTEGER	read-write	This value defines the maximum allowable number of External Addresses for the domain that this router exists in. The default value of this field is 0.
INT wfOsiCksumIsPdus	1.3.6.1.4.1.18.3.5.6.1.13	INTEGER	read-write	This value indicates whether ISIS PDUs will carry a checksum.
STR wfOsiL1LspPassword	1.3.6.1.4.1.18.3.5.6.1.14	DisplayString	read-write	This assigns a password such that only L1 Lsps with the matching password will be accepted. All L1 Lsps generated by this system will contain this string in the password option.
STR wfOsiL2LspPassword	1.3.6.1.4.1.18.3.5.6.1.15	DisplayString	read-write	This assigns a password such that only L2 Lsps with the matching password will be accepted. All L2 Lsps generated by this system will contain this string in the password option.
OCT wfOsiAreaAddr	1.3.6.1.4.1.18.3.5.6.1.16	OCTET STRING	read-write	This Assigns the area address for this router. This field must be filled in. If the user doesn't enter a value, then assign 490040. Site Manager must force the user to enter at least a 3-byte value for this field.
OCT wfOsiAreaAddrAlias1	1.3.6.1.4.1.18.3.5.6.1.17	OCTET STRING	read-write	This Assigns the first area address alias for this router. This field does no have to be filled in, but if the user tries to enter a value, Site Manager must make sure that it is at least 3-bytes in length.
OCT wfOsiAreaAddrAlias2	1.3.6.1.4.1.18.3.5.6.1.18	OCTET STRING	read-write	This Assigns the second area address alias for this router. This field does no have to be filled in, but if the user tries to enter a value, Site Manager must make sure that it is at least 3-bytes in length.
CTR wfOsiCorruptedLsps	1.3.6.1.4.1.18.3.5.6.1.19	Counter	read-only	Number of Corrupted Lsps Detected.
CTR wfOsiL1LspDbOverloads	1.3.6.1.4.1.18.3.5.6.1.20	Counter	read-only	Number of times the L1 Lsp Database Overload event has been generated.
CTR wfOsiL2LspDbOverloads	1.3.6.1.4.1.18.3.5.6.1.21	Counter	read-only	Number of times the L2 Lsp Database Overload event has been generated.
CTR wfOsiManAddrDroppedAreas	1.3.6.1.4.1.18.3.5.6.1.22	Counter	read-only	Number of times the Manual Address Dropped from Area event has been generated.
CTR wfOsiSeqNumberSkips	1.3.6.1.4.1.18.3.5.6.1.23	Counter	read-only	Number of times the Sequence Number Skipped event has been generated.
CTR wfOsiOwnLspPurges	1.3.6.1.4.1.18.3.5.6.1.24	Counter	read-only	Number of times the Own Lsp Purged event has been generated.
CTR wfOsiOthLspPurges	1.3.6.1.4.1.18.3.5.6.1.25	Counter	read-only	Number of times the Other Lsp Purged event has been generated.
CTR wfOsiExceedMaxSeqNums	1.3.6.1.4.1.18.3.5.6.1.26	Counter	read-only	Number of times the Attempt tp Exceed Maximum Sequence Number event has been generated.
OCT wfOsiNearestL2Is	1.3.6.1.4.1.18.3.5.6.1.27	OCTET STRING	read-only	This is the ID of the Nearest L2 system in this area.
INT wfOsiMaxDynEs	1.3.6.1.4.1.18.3.5.6.1.28	INTEGER	read-write	This is the maximum number of dynamically learned (via Hello) End Systems allowed per slot.
INT wfOsiMaxDynL1Is	1.3.6.1.4.1.18.3.5.6.1.29	INTEGER	read-write	This is the maximum number of dynamically learned (via Hello) Level 1 Intermediate Systems allowed per slot.
INT wfOsiMaxDynL2Is	1.3.6.1.4.1.18.3.5.6.1.30	INTEGER	read-write	This is the maximum number of dynamically learned (via Hello) Level 2 Intermediate Systems allowed per slot.
CTR wfOsiNumDynEsAdjs	1.3.6.1.4.1.18.3.5.6.1.31	Counter	read-only	Number of Dynamic ES adjs the osi master gate receives from the cct gate.
CTR wfOsiNumDynL1Adjs	1.3.6.1.4.1.18.3.5.6.1.32	Counter	read-only	Number of Dynamic L1 adjs the osi master gate receives from the cct gate.
CTR wfOsiNumDynL2Adjs	1.3.6.1.4.1.18.3.5.6.1.33	Counter	read-only	Number of Dynamic L2 adjs the osi master gate receives from the cct gate.
CTR wfOsiNumL1Routes	1.3.6.1.4.1.18.3.5.6.1.34	Counter	read-only	Number of L1 Routes. WL 2.27.93
CTR wfOsiNumL2Routes	1.3.6.1.4.1.18.3.5.6.1.35	Counter	read-only	Number of L2 Routes. WL 2.27.93
CTR wfOsiNumDynPtpEsAdjs	1.3.6.1.4.1.18.3.5.6.1.36	Counter	read-only	Number of Dynamic Point-to-Point ES adjs the osi master gate receives on.
CTR wfOsiNumDynPtpIsAdjs	1.3.6.1.4.1.18.3.5.6.1.37	Counter	read-only	Number of Dynamic Point-to-Point IS adjs the osi master gate receives on .
INT wfOsiClnpSrcRtOptionDisable	1.3.6.1.4.1.18.3.5.6.1.38	INTEGER	read-write	Enable/Disable processing of Source Route options in CLNP PDUs. This is required for GOSIP v2 support. GOSIP prohibits processing Source Routing options.
CTR wfOsiNumL1Lsps	1.3.6.1.4.1.18.3.5.6.1.39	Counter	read-only	Number of L1 LSPs stored in database.
CTR wfOsiNumL2Lsps	1.3.6.1.4.1.18.3.5.6.1.40	Counter	read-only	Number of L2 LSPs stored in database.
INT wfOsiFletchRelaxedEnable	1.3.6.1.4.1.18.3.5.6.1.41	INTEGER	read-write	Enable/Disable whether non-standard Fletcher Checksums are allowed in LSP's. If enabled, a log message will be generated, otherwise the LSP will be rejected.
wfOsiStaticRouteTable	1.3.6.1.4.1.18.3.5.6.2		not-accessible	This table contains all the static routes for this system.
wfOsiStaticRouteEntry	1.3.6.1.4.1.18.3.5.6.2.1		not-accessible	This is the Static Route Entry for the Static Route Table.
INT wfOsiStaticRouteDelete	1.3.6.1.4.1.18.3.5.6.2.1.1	INTEGER	read-write	Create/Delete parameter for Osi Static Route Record.
INT wfOsiStaticRouteDisable	1.3.6.1.4.1.18.3.5.6.2.1.2	INTEGER	read-write	Enable/Disable parameter for this Static Route.
OCT wfOsiStaticRouteAddr	1.3.6.1.4.1.18.3.5.6.2.1.3	OCTET STRING	read-only	This specifies the address of the static route. It is also the inst_id.
INT wfOsiStaticRouteNibbleLength	1.3.6.1.4.1.18.3.5.6.2.1.4	INTEGER	read-write	This is the length in nibbles of the static route address. It is necessary to specify it in nibbles since the static route may be an external address which can be specified in nibbles.
OCT wfOsiStaticRouteNextHopIs	1.3.6.1.4.1.18.3.5.6.2.1.5	OCTET STRING	read-write	This is the 6-octet ID of the next Hop IS that all data destined to wfOsiStaticRouteAddr will be forwarded to.
INT wfOsiStaticRouteType	1.3.6.1.4.1.18.3.5.6.2.1.6	INTEGER	read-write	This specifies whether the destination is an End System, an area, or an external Domain.
INT wfOsiStaticRouteCost	1.3.6.1.4.1.18.3.5.6.2.1.7	INTEGER	read-write	This value is the cost to get to this address.
wfOsiCircuitTable	1.3.6.1.4.1.18.3.5.6.3		not-accessible	This Table contains all circuit configuration info counters available on a per circuit basis.
wfOsiCircuitEntry	1.3.6.1.4.1.18.3.5.6.3.1		not-accessible	This is the circuit entry record that appears in the Circuit Table.
INT wfOsiCircuitDelete	1.3.6.1.4.1.18.3.5.6.3.1.1	INTEGER	read-write	This value determines whether this circuit is configured.
INT wfOsiCircuitDisable	1.3.6.1.4.1.18.3.5.6.3.1.2	INTEGER	read-write	Enable/Disable parameter for this circuit.
INT wfOsiCircuitState	1.3.6.1.4.1.18.3.5.6.3.1.3	INTEGER	read-only	This indicates whether the circuit state is up or down.
INT wfOsiCircuitId	1.3.6.1.4.1.18.3.5.6.3.1.4	INTEGER	read-only	A unique value for each known circuit.
INT wfOsiCircuitRouterLevel	1.3.6.1.4.1.18.3.5.6.3.1.5	INTEGER	read-write	This is the level protocol that the circuit runs. Its a bit mask to allow for some combination of L1, L2, External, ES-IS-only.
INT wfOsiCircuitL1DefaultMetric	1.3.6.1.4.1.18.3.5.6.3.1.6	INTEGER	read-write	This is the default cost of using this circuit for L1 traffic.
INT wfOsiCircuitL2DefaultMetric	1.3.6.1.4.1.18.3.5.6.3.1.7	INTEGER	read-write	This is the default cost of using this circuit for L2 traffic.
INT wfOsiCircuitL1DrPriority	1.3.6.1.4.1.18.3.5.6.3.1.8	INTEGER	read-write	This is the priority for this system to become L1 designated router on this LAN circuit.
INT wfOsiCircuitL2DrPriority	1.3.6.1.4.1.18.3.5.6.3.1.9	INTEGER	read-write	This is the priority for this system to become L2 designated router on this LAN circuit.
INT wfOsiCircuitIsisHelloTimer	1.3.6.1.4.1.18.3.5.6.3.1.10	INTEGER	read-write	This is the period (secs) between IIH hello transmissions.
INT wfOsiCircuitEsisHelloTimer	1.3.6.1.4.1.18.3.5.6.3.1.11	INTEGER	read-write	This is the period (secs) between ISH hello transmissions.
INT wfOsiCircuitEshConfigTime	1.3.6.1.4.1.18.3.5.6.3.1.12	INTEGER	read-write	This is the suggested time between ESH transmissions from an ES went in ISHs (ESCT).
STR wfOsiCircuitPassword	1.3.6.1.4.1.18.3.5.6.3.1.13	DisplayString	read-write	This is Circuit Password for this circuit. Used to filter out Hellos from systems without the correct password.
CTR wfOsiCircuitReceivedPkts	1.3.6.1.4.1.18.3.5.6.3.1.14	Counter	read-only	This is the number of pkts that have been received on this circuit.
CTR wfOsiCircuitSentPkts	1.3.6.1.4.1.18.3.5.6.3.1.15	Counter	read-only	This is the number of pkts sent out this circuit.
CTR wfOsiCircuitDroppedPkts	1.3.6.1.4.1.18.3.5.6.3.1.16	Counter	read-only	This is the number of pkts dropped on this circuit.
CTR wfOsiCircuitFragmentedPdus	1.3.6.1.4.1.18.3.5.6.3.1.17	Counter	read-only	This is the number of pdus that had to be fragmented when forwarded out this circuit.
CTR wfOsiCircuitCongestionDiscards	1.3.6.1.4.1.18.3.5.6.3.1.18	Counter	read-only	This is the number of PDUs dropped because of congestion.
CTR wfOsiCircuitAddrUnreachDiscards	1.3.6.1.4.1.18.3.5.6.3.1.19	Counter	read-only	This is the number of PDUs dropped because the destination is unreachable.
CTR wfOsiCircuitAgedPduDiscards	1.3.6.1.4.1.18.3.5.6.3.1.20	Counter	read-only	This is the number of PDUs dropped because of aging.
CTR wfOsiCircuitPduFormatErrDiscards	1.3.6.1.4.1.18.3.5.6.3.1.21	Counter	read-only	This is the number of PDUs dropped because of Format Error.
CTR wfOsiCircuitUnsuppOptsDiscards	1.3.6.1.4.1.18.3.5.6.3.1.22	Counter	read-only	This is the number of PDUs dropped because they contain unsupported options.
CTR wfOsiCircuitSentErrorReports	1.3.6.1.4.1.18.3.5.6.3.1.23	Counter	read-only	This is the number of error reports sent out this circuit.
CTR wfOsiCircuitReceivedControlPdus	1.3.6.1.4.1.18.3.5.6.3.1.24	Counter	read-only	This is the number of ESIS or ISIS PDUs received on this circuit.
CTR wfOsiCircuitSentControlPdus	1.3.6.1.4.1.18.3.5.6.3.1.25	Counter	read-only	This is the number of ESIS or ISIS PDUs sent out this circuit.
CTR wfOsiCircuitStateChanges	1.3.6.1.4.1.18.3.5.6.3.1.26	Counter	read-only	This is the number of times the circuit goes from down to up or from up to down.
CTR wfOsiCircuitAdjStateChanges	1.3.6.1.4.1.18.3.5.6.3.1.27	Counter	read-only	This is the number of times an adjacency off of this circuit goes from down to up or from up to down state.
CTR wfOsiCircuitInitFailures	1.3.6.1.4.1.18.3.5.6.3.1.28	Counter	read-only	This is the number of times this circuit fails to initialize.
CTR wfOsiCircuitRejectedAdjs	1.3.6.1.4.1.18.3.5.6.3.1.29	Counter	read-only	This is the number of Adjacencies that were rejected on this circuit.
CTR wfOsiCircuitReceivedBadLsps	1.3.6.1.4.1.18.3.5.6.3.1.30	Counter	read-only	This is the number of bad Lsps received on this circuit.
CTR wfOsiCircuitReceivedBadSnps	1.3.6.1.4.1.18.3.5.6.3.1.31	Counter	read-only	This is the number of BAD Sequence Number Pdus received on this circuit.
CTR wfOsiCircuitReceivedBadEshs	1.3.6.1.4.1.18.3.5.6.3.1.32	Counter	read-only	This is the number of bad ESHs received on this circuit.
CTR wfOsiCircuitReceivedBadL1Iihs	1.3.6.1.4.1.18.3.5.6.3.1.33	Counter	read-only	This is the number of bad L1 IIHs received on this circuit.
CTR wfOsiCircuitReceivedBadL2Iihs	1.3.6.1.4.1.18.3.5.6.3.1.34	Counter	read-only	This is the number of bad L2 IIHs received on this circuit.
CTR wfOsiCircuitL1DrChanges	1.3.6.1.4.1.18.3.5.6.3.1.35	Counter	read-only	This is the number of times the L1 Designated Router has been elected on this circuit.
CTR wfOsiCircuitL2DrChanges	1.3.6.1.4.1.18.3.5.6.3.1.36	Counter	read-only	This is the number of times the L2 Designated Router has been elected on this circuit.
CTR wfOsiCircuitClnpForwarding	1.3.6.1.4.1.18.3.5.6.3.1.37	Counter	read-only	This shows whether forwarding is enabled over this circuit.
CTR wfOsiCircuitClnpDefaultLifeTime	1.3.6.1.4.1.18.3.5.6.3.1.38	Counter	read-only	This is the lifetime included in clnp pdus generated by this router (i.e. echo and echo reply pdus, error report pdus).
CTR wfOsiCircuitClnpInReceives	1.3.6.1.4.1.18.3.5.6.3.1.39	Counter	read-only	This is the number of CLNP pdus received from this circuit.
CTR wfOsiCircuitClnpInAddrErrors	1.3.6.1.4.1.18.3.5.6.3.1.40	Counter	read-only	This is the number of CLNP pdus recived from this circuit with Address format errors.
CTR wfOsiCircuitClnpForwPdus	1.3.6.1.4.1.18.3.5.6.3.1.41	Counter	read-only	This is the number of Clnp PDUs received on this circuit that are forwarded.
CTR wfOsiCircuitClnpInUnknownNlps	1.3.6.1.4.1.18.3.5.6.3.1.42	Counter	read-only	This is the number of Clnp PDUs received on this circuit where the network layer addressed is unknown (Bad NLPID).
CTR wfOsiCircuitClnpInDelivers	1.3.6.1.4.1.18.3.5.6.3.1.43	Counter	read-only	This is the number of Clnp PDUs received on this circuit whose destination is this router.
CTR wfOsiCircuitClnpInUnknownUlps	1.3.6.1.4.1.18.3.5.6.3.1.44	Counter	read-only	This is number of Clnp PDUs received on this circuit addressed to this router where the upper layer is unknown.
CTR wfOsiCircuitClnpSegCreates	1.3.6.1.4.1.18.3.5.6.3.1.45	Counter	read-only	This is the number of CLNP segments created from pdus received on this circuit.
CTR wfOsiCircuitClnpInOpts	1.3.6.1.4.1.18.3.5.6.3.1.46	Counter	read-only	This is the number of CLNP pdus received with an options portion.
CTR wfOsiCircuitClnpOutOpts	1.3.6.1.4.1.18.3.5.6.3.1.47	Counter	read-only	This is the number of CLNP pdus sent with an options portion.
CTR wfOsiCircuitEsisEshIns	1.3.6.1.4.1.18.3.5.6.3.1.48	Counter	read-only	This is the number of ESHs received from this circuit.
CTR wfOsiCircuitEsisIshOuts	1.3.6.1.4.1.18.3.5.6.3.1.49	Counter	read-only	This is the number of ISHs sent out this circuit.
CTR wfOsiCircuitEsisRduOuts	1.3.6.1.4.1.18.3.5.6.3.1.50	Counter	read-only	This is the number of Redirects sent out this circuit.
OCT wfOsiCircuitL1DesignatedRouter	1.3.6.1.4.1.18.3.5.6.3.1.51	OCTET STRING	read-only	This is the ID of the L1 Designated Router on this circuit.
OCT wfOsiCircuitL2DesignatedRouter	1.3.6.1.4.1.18.3.5.6.3.1.52	OCTET STRING	read-only	This is the ID of the L2 Designated Router on this circuit.
CTR wfOsiCircuitClnpOutEchoReplies	1.3.6.1.4.1.18.3.5.6.3.1.53	Counter	read-only	This is the number of CLNP Echo Replies sent out this circuit.
CTR wfOsiCircuitClnpOutEchoRequests	1.3.6.1.4.1.18.3.5.6.3.1.54	Counter	read-only	This is the number of Clnp Echo Requests sent out this circuit.
CTR wfOsiCircuitClnpInEchoReplies	1.3.6.1.4.1.18.3.5.6.3.1.55	Counter	read-only	This is the number of CLNP Echo Replies received on this circuit.
CTR wfOsiCircuitClnpInEchoRequests	1.3.6.1.4.1.18.3.5.6.3.1.56	Counter	read-only	This is the number of CLNP Echo Requests recived on this circuit.
CTR wfOsiCircuitNumDynEsAdjs	1.3.6.1.4.1.18.3.5.6.3.1.57	Counter	read-only	This is the number of Dynamic End System Adjacencies formed on this circuit.
CTR wfOsiCircuitNumDynL1Adjs	1.3.6.1.4.1.18.3.5.6.3.1.58	Counter	read-only	This is the number of Dynamic Level 1 Intermediate System Adjacencies formed on this circuit.
CTR wfOsiCircuitNumDynL2Adjs	1.3.6.1.4.1.18.3.5.6.3.1.59	Counter	read-only	This is the number of Dynamic Level 2 Intermediate System Adjacencies formed on this circuit.
CTR wfOsiCircuitNumDynPtpIsAdjs	1.3.6.1.4.1.18.3.5.6.3.1.60	Counter	read-only	This is the number of Dynamic Intermediate System Point-to-Point Adjacencies formed on this circuit.
CTR wfOsiCircuitNumDynPtpEsAdjs	1.3.6.1.4.1.18.3.5.6.3.1.61	Counter	read-only	This is the number of Dynamic End System Point-to-Point Adjaciences formed on this circuit.
CTR wfOsiCircuitBadIshReceived	1.3.6.1.4.1.18.3.5.6.3.1.62	Counter	read-only	This is the number of bad Intermediate System Hellos received on this circuit. These will only be received on Point-to-Point circuits.
CTR wfOsiCircuitEsisIshIns	1.3.6.1.4.1.18.3.5.6.3.1.63	Counter	read-only	This is the number of good Intermediate System Hellos received on this circuit. These will only be received on Point-to-Point circuits.
INT wfOsiCircuitIihHoldMultiplier	1.3.6.1.4.1.18.3.5.6.3.1.64	INTEGER	read-write	This is the multiplier value used to compute the hold time set in the IIH PDUs transmitted from this router. Hold time equals IIH Timer times IIH Hold Multiplier.
INT wfOsiCircuitIshHoldMultiplier	1.3.6.1.4.1.18.3.5.6.3.1.65	INTEGER	read-write	This is the multiplier value used to compute the hold time set in the ISH PDUs transmitted from this router. Hold time equals IIH Timer times IIH Hold Multiplier.
INT wfOsiCircuitDisableRedirect	1.3.6.1.4.1.18.3.5.6.3.1.66	INTEGER	read-write	Allow Redirects to be disabled. This is required when operating over Frame Relay in group mode in a partial mesh topology.
wfOsiExternalAddressTable	1.3.6.1.4.1.18.3.5.6.4		not-accessible	This is the table of External Addresses for this Router.
wfOsiExternalAddressEntry	1.3.6.1.4.1.18.3.5.6.4.1		not-accessible	This is the External Address Record for this Router.
INT wfOsiExtAddrDelete	1.3.6.1.4.1.18.3.5.6.4.1.1	INTEGER	read-write	This is the Create/Delete parameter for this ExtAddr entry.
INT wfOsiExtAddrDisable	1.3.6.1.4.1.18.3.5.6.4.1.2	INTEGER	read-write	Enable/Disable parameter for this ExtAddr.
OCT wfOsiExtAddr	1.3.6.1.4.1.18.3.5.6.4.1.3	OCTET STRING	read-only	This is the prefix external address. It is also the inst_id.
INT wfOsiExtAddrCircuit	1.3.6.1.4.1.18.3.5.6.4.1.4	INTEGER	read-only	This is the circuit to go out for this adj.
INT wfOsiExtAddrNibbleLength	1.3.6.1.4.1.18.3.5.6.4.1.5	INTEGER	read-write	This is the length in nibbles of the external address.
OCT wfOsiExtAddrSnpa	1.3.6.1.4.1.18.3.5.6.4.1.6	OCTET STRING	read-write	This is the SNPA of the neighbor on this circuit.
INT wfOsiExtAddrCost	1.3.6.1.4.1.18.3.5.6.4.1.7	INTEGER	read-write	This is the external metric cost to this address.
wfOsiStaticEsTable	1.3.6.1.4.1.18.3.5.6.5		not-accessible	This is the Static ES Table for this router.
wfOsiStaticEsEntry	1.3.6.1.4.1.18.3.5.6.5.1		not-accessible	This is the Static ES entry for the Static ES Table.
INT wfOsiStaticEsDelete	1.3.6.1.4.1.18.3.5.6.5.1.1	INTEGER	read-write	This is the Create/Delete parameter for this Static ES entry.
INT wfOsiStaticEsDisable	1.3.6.1.4.1.18.3.5.6.5.1.2	INTEGER	read-write	Enable/Disable parameter for this Static ES.
OCT wfOsiStaticEsId	1.3.6.1.4.1.18.3.5.6.5.1.3	OCTET STRING	read-only	This is the ESID of the neighbor.
INT wfOsiStaticEsCircuit	1.3.6.1.4.1.18.3.5.6.5.1.4	INTEGER	read-only	This is the circuit to go out for this adj.
OCT wfOsiStaticEsSnpa	1.3.6.1.4.1.18.3.5.6.5.1.5	OCTET STRING	read-write	This is the SNPA of the neighbor on this circuit.
wfOsiTrafficFilterTable	1.3.6.1.4.1.18.3.5.6.6		not-accessible	OSI Traffic Filters
wfOsiTrafficFilterEntry	1.3.6.1.4.1.18.3.5.6.6.1		not-accessible	A traffic filter definition
INT wfOsiTrafficFilterDelete	1.3.6.1.4.1.18.3.5.6.6.1.1	INTEGER	read-write	Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
INT wfOsiTrafficFilterDisable	1.3.6.1.4.1.18.3.5.6.6.1.2	INTEGER	read-write	Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
INT wfOsiTrafficFilterStatus	1.3.6.1.4.1.18.3.5.6.6.1.3	INTEGER	read-only	Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
CTR wfOsiTrafficFilterCounter	1.3.6.1.4.1.18.3.5.6.6.1.4	Counter	read-only	The number of received packets that have matched this rule.
OPA wfOsiTrafficFilterDefinition	1.3.6.1.4.1.18.3.5.6.6.1.5	Opaque	read-write	The filter rule definition.
INT wfOsiTrafficFilterReserved	1.3.6.1.4.1.18.3.5.6.6.1.6	INTEGER	read-only	Reserved field.
INT wfOsiTrafficFilterCircuit	1.3.6.1.4.1.18.3.5.6.6.1.7	INTEGER	read-only	The ID of the Circuit to which the filter is applied.
INT wfOsiTrafficFilterRuleNumber	1.3.6.1.4.1.18.3.5.6.6.1.8	INTEGER	read-only	ID for the rule.
INT wfOsiTrafficFilterFragment	1.3.6.1.4.1.18.3.5.6.6.1.9	INTEGER	read-only	Fragment number - for large rules.
STR wfOsiTrafficFilterName	1.3.6.1.4.1.18.3.5.6.6.1.10	DisplayString	read-write	name of the rule number
wfOsiL1LspHdrTable	1.3.6.1.4.1.18.3.5.6.7		not-accessible	2 u_int32's so the inst_id len is 2.
wfOsiL1LspHdrEntry	1.3.6.1.4.1.18.3.5.6.7.1		not-accessible	A Record in the Level 1 Lsp Header Table
OCT wfOsiL1LspHdrLspId	1.3.6.1.4.1.18.3.5.6.7.1.1	OCTET STRING	read-only	LSPID = Source ID + Pseudo-node ID + LSP number
INT wfOsiL1LspHdrLifetime	1.3.6.1.4.1.18.3.5.6.7.1.2	INTEGER	read-only	Lsp Lifetime
INT wfOsiL1LspHdrSeqnum	1.3.6.1.4.1.18.3.5.6.7.1.3	INTEGER	read-only	Lsp sequence number
OCT wfOsiL1LspHdrFlags	1.3.6.1.4.1.18.3.5.6.7.1.4	OCTET STRING	read-only	Flags: P/ATT/LSPDBOL/IS type
OCT wfOsiL1LspHdrCksum	1.3.6.1.4.1.18.3.5.6.7.1.5	OCTET STRING	read-only	Checksum
wfOsiL2LspHdrTable	1.3.6.1.4.1.18.3.5.6.8		not-accessible	2 u_int32's so the inst_id len is 2.
wfOsiL2LspHdrEntry	1.3.6.1.4.1.18.3.5.6.8.1		not-accessible	A Record in the Lsp Header Table
OCT wfOsiL2LspHdrLspId	1.3.6.1.4.1.18.3.5.6.8.1.1	OCTET STRING	read-only	LSPID = Source ID + Pseudo-node ID + LSP number
INT wfOsiL2LspHdrLifetime	1.3.6.1.4.1.18.3.5.6.8.1.2	INTEGER	read-only	Lsp Lifetime
INT wfOsiL2LspHdrSeqnum	1.3.6.1.4.1.18.3.5.6.8.1.3	INTEGER	read-only	Lsp sequence number
OCT wfOsiL2LspHdrFlags	1.3.6.1.4.1.18.3.5.6.8.1.4	OCTET STRING	read-only	Flags: P/ATT/LSPDBOL/IS type
OCT wfOsiL2LspHdrCksum	1.3.6.1.4.1.18.3.5.6.8.1.5	OCTET STRING	read-only	Checksum
wfOsiDynAdjTable	1.3.6.1.4.1.18.3.5.6.9		not-accessible	Dynamic Adjacency Table
wfOsiDynAdjEntry	1.3.6.1.4.1.18.3.5.6.9.1		not-accessible	Adjacency Table - the real index is the adjacency id
INT wfOsiDynAdjId	1.3.6.1.4.1.18.3.5.6.9.1.1	INTEGER	read-only	Index in the Adjacency Table
INT wfOsiDynAdjDatabase	1.3.6.1.4.1.18.3.5.6.9.1.2	INTEGER	read-only	Database into which the Adjacency is stored, 1=ES, 2=Level 1 IS, 3=Level 2 IS.
INT wfOsiDynAdjType	1.3.6.1.4.1.18.3.5.6.9.1.3	INTEGER	read-only	The type of adjacency. (see Osi_const.h)
INT wfOsiDynAdjState	1.3.6.1.4.1.18.3.5.6.9.1.4	INTEGER	read-only	The state of the adjacency. INITIALIZING, UP or FAILED
INT wfOsiDynAdjCircuitId	1.3.6.1.4.1.18.3.5.6.9.1.5	INTEGER	read-only	A unique value for each known circuit.
INT wfOsiDynAdjHoldTime	1.3.6.1.4.1.18.3.5.6.9.1.6	INTEGER	read-only	Hold Time received from neighbor.
INT wfOsiDynAdjPriority	1.3.6.1.4.1.18.3.5.6.9.1.7	INTEGER	read-only	Priority to become designated router. IS only.
OCT wfOsiDynAdjSnpaAddr	1.3.6.1.4.1.18.3.5.6.9.1.8	OCTET STRING	read-only	SNAP address for neighbor.
OCT wfOsiDynAdjNsapAddr	1.3.6.1.4.1.18.3.5.6.9.1.9	OCTET STRING	read-only	Neighbor address (NSAP).
OCT wfOsiDynAdjLanId	1.3.6.1.4.1.18.3.5.6.9.1.10	OCTET STRING	read-only	LAN ID from Designated Router. IS only.
wfOsiL1RoutesTable	1.3.6.1.4.1.18.3.5.6.10		not-accessible	This is the L1 Routes Table for this router.
wfOsiL1RouteEntry	1.3.6.1.4.1.18.3.5.6.10.1		not-accessible	This is the L1 Route entry for the Routes Table.
OCT wfOsiL1RouteId	1.3.6.1.4.1.18.3.5.6.10.1.1	OCTET STRING	read-only	This is the SysID of the L1 Destination.
INT wfOsiL1RoutePathSplit	1.3.6.1.4.1.18.3.5.6.10.1.2	INTEGER	read-only	This assigns a number to each equal cost path to the destination. There can be up to 2 equal cost paths to a destination.
INT wfOsiL1RouteType	1.3.6.1.4.1.18.3.5.6.10.1.3	INTEGER	read-only	This tells what kind of a route this entry is.
OCT wfOsiL1RouteNextHopSnpa	1.3.6.1.4.1.18.3.5.6.10.1.4	OCTET STRING	read-only	This is the SNPA of the next hop adj for this route.
OCT wfOsiL1RouteNextHopId	1.3.6.1.4.1.18.3.5.6.10.1.5	OCTET STRING	read-only	This is the ID of the next hop adjacency to this route. If its just an ES then it is the 6byte System ID. If the next HOP is an IS then it is the NET.
INT wfOsiL1RouteNextHopType	1.3.6.1.4.1.18.3.5.6.10.1.6	INTEGER	read-only	This is the adj type of the next hop for this route.
INT wfOsiL1RouteNextHopCircuit	1.3.6.1.4.1.18.3.5.6.10.1.7	INTEGER	read-only	This is the circuit to forward out for this route.
INT wfOsiL1RouteDefaultMetricCost	1.3.6.1.4.1.18.3.5.6.10.1.8	INTEGER	read-only	This is the cost to from this system to this destination.
wfOsiL2RoutesTable	1.3.6.1.4.1.18.3.5.6.11		not-accessible	This is the L2 Routes Table for this router.
wfOsiL2RouteEntry	1.3.6.1.4.1.18.3.5.6.11.1		not-accessible	This is the L2 Route entry for the Routes Table.
OCT wfOsiL2RouteId	1.3.6.1.4.1.18.3.5.6.11.1.1	OCTET STRING	read-only	This is the SysID of the L2 Destination.
INT wfOsiL2RoutePathSplit	1.3.6.1.4.1.18.3.5.6.11.1.2	INTEGER	read-only	This assigns a number to each equal cost path to the destination. There can be up to 2 equal cost paths to a destination.
INT wfOsiL2RouteType	1.3.6.1.4.1.18.3.5.6.11.1.3	INTEGER	read-only	This tells what kind of a route this entry is.
OCT wfOsiL2RouteNextHopSnpa	1.3.6.1.4.1.18.3.5.6.11.1.4	OCTET STRING	read-only	This is the SNPA of the neighbor on this circuit.
OCT wfOsiL2RouteNextHopId	1.3.6.1.4.1.18.3.5.6.11.1.5	OCTET STRING	read-only	This is the ID of the next hop adjacency to this route. If its just an ES then it is the 6byte System ID. If the next HOP is an IS then it is the NET.
INT wfOsiL2RouteNextHopType	1.3.6.1.4.1.18.3.5.6.11.1.6	INTEGER	read-only	This is the adj type of the next hop for this route.
INT wfOsiL2RouteNextHopCircuit	1.3.6.1.4.1.18.3.5.6.11.1.7	INTEGER	read-only	This is the circuit to go out for this adj.
INT wfOsiL2RouteDefaultMetricCost	1.3.6.1.4.1.18.3.5.6.11.1.8	INTEGER	read-only	This is the cost to from this system to this destination.
wfOsiDecnetTrans	1.3.6.1.4.1.18.3.5.6.12
INT wfOsiDecnetTransDelete	1.3.6.1.4.1.18.3.5.6.12.1	INTEGER	read-write	This value determines whether DECnet Phase 4 to Phase 5 Transition functions are configured.
INT wfOsiDecnetTransDisable	1.3.6.1.4.1.18.3.5.6.12.2	INTEGER	read-write	This value determines whether DECnet Phase 4 to Phase 5 Transition functions are enabled.
INT wfOsiDecnetTransState	1.3.6.1.4.1.18.3.5.6.12.3	INTEGER	read-only	This value displays the state of the DECnet Phase 4 to Phase 5 Transition function.
CTR wfOsiDecnetTransPhase4Pkts	1.3.6.1.4.1.18.3.5.6.12.4	Counter	read-only	Number of successfully translated Phase 4 packets
CTR wfOsiDecnetTransSegFail	1.3.6.1.4.1.18.3.5.6.12.5	Counter	read-only	Number of times Phase 5 translation failed because the packet was segmented.
CTR wfOsiDecnetTransNselFail	1.3.6.1.4.1.18.3.5.6.12.6	Counter	read-only	Number of times Phase 5 translation failed because the NSELs were not the same.
CTR wfOsiDecnetTransUnrFail	1.3.6.1.4.1.18.3.5.6.12.7	Counter	read-only	Number of times Phase 5 failed to find a route to the destination.
CTR wfOsiDecnetTransNumPhase4Es	1.3.6.1.4.1.18.3.5.6.12.8	Counter	read-only	Number of Phase 4 ES Adjacencies announced by the Phase 4 (DECnet IV) router.
wfOsiAreaAddressTable	1.3.6.1.4.1.18.3.5.6.13		not-accessible	This is the table of Area Addresses for this Router.
wfOsiAreaAddressEntry	1.3.6.1.4.1.18.3.5.6.13.1		not-accessible	This is the Area Address Record for this Router.
INT wfOsiAreaAddrDelete	1.3.6.1.4.1.18.3.5.6.13.1.1	INTEGER	read-write	This is the Create/Delete parameter for this AreaAddr entry.
INT wfOsiAreaAddrDisable	1.3.6.1.4.1.18.3.5.6.13.1.2	INTEGER	read-write	Enable/Disable parameter for this AreaAddr.
OCT wfOsiAreaAddress	1.3.6.1.4.1.18.3.5.6.13.1.3	OCTET STRING	read-only	This is the prefix area address. It is also the inst_id.
wfOsiTarpEntry	1.3.6.1.4.1.18.3.5.6.14
INT wfOsiTarpCreate	1.3.6.1.4.1.18.3.5.6.14.1	INTEGER	read-write	This value determines whether OSI Tarp is configured on this slot.
INT wfOsiTarpEnable	1.3.6.1.4.1.18.3.5.6.14.2	INTEGER	read-write	This value dtermines if OSI Tarp is to startup.
INT wfOsiTarpState	1.3.6.1.4.1.18.3.5.6.14.3	INTEGER	read-only	This value describes the state of OSI Tarp.
STR wfOsiTarpTID	1.3.6.1.4.1.18.3.5.6.14.4	DisplayString	read-write	This value contains the Target Identifier assigned to the router (Network Entity).
INT wfOsiTarpOriginate	1.3.6.1.4.1.18.3.5.6.14.5	INTEGER	read-write	This value determines if TARP is allowed to originate any tarp requests.
INT wfOsiTarpLifetime	1.3.6.1.4.1.18.3.5.6.14.6	INTEGER	read-write	This value determines what the lifetime of of TARP packets originated by this router will be.
INT wfOsiTarpStartSeq	1.3.6.1.4.1.18.3.5.6.14.7	INTEGER	read-write	This value determines what the starting sequence number of TARP packets originated by this router will be.
INT wfOsiTarpNextSeq	1.3.6.1.4.1.18.3.5.6.14.8	INTEGER	read-only	This value determines what the next sequence number of TARP packets originated by this router will be.
INT wfOsiTarpTarPro	1.3.6.1.4.1.18.3.5.6.14.9	INTEGER	read-write	This value describes what the Protocol Address Type field within the TARP packet must be. A value of 'FE' describes a CLNP address type.
INT wfOsiTarpTDC	1.3.6.1.4.1.18.3.5.6.14.10	INTEGER	read-write	This value determines whether or not TARP uses and maintains a Tarp Data Cache.
INT wfOsiTarpL2TDC	1.3.6.1.4.1.18.3.5.6.14.11	INTEGER	read-write	This value determines whether or not TARP uses and maintains a Level 2 Tarp Data Cache.
INT wfOsiTarpT1	1.3.6.1.4.1.18.3.5.6.14.12	INTEGER	read-write	This value configures the Tarp T1 Timer - how many seconds to wait for a response to a Type1 Request PDU.
INT wfOsiTarpT2	1.3.6.1.4.1.18.3.5.6.14.13	INTEGER	read-write	This value configures the Tarp T2 Timer - how many seconds to wait for a response to a Type2 Request PDU.
INT wfOsiTarpT3	1.3.6.1.4.1.18.3.5.6.14.14	INTEGER	read-write	This value configures the Tarp T3 Timer - how many seconds to wait for a response to a Type5 Request PDU.
INT wfOsiTarpT4	1.3.6.1.4.1.18.3.5.6.14.15	INTEGER	read-write	This value configures the Tarp T4 Timer, which is used during the Error Recovery process after T2 expires.
INT wfOsiTarpLDBTimer	1.3.6.1.4.1.18.3.5.6.14.16	INTEGER	read-write	This value configures the Loop Detection Buffer's Entry Timer.
INT wfOsiTarpLDBFlush	1.3.6.1.4.1.18.3.5.6.14.17	INTEGER	read-write	This value configures the timer that signals the flushing of the Loop Detection Buffer.
INT wfOsiTarpLDBSize	1.3.6.1.4.1.18.3.5.6.14.18	INTEGER	read-write	This value specifies the maximum number of entries the the Loop Detection Buffer can hold.
CTR wfOsiTarpType1Rcv	1.3.6.1.4.1.18.3.5.6.14.19	Counter	read-only	This value counts the number of Type 1 Tarp packets received by this interface.
CTR wfOsiTarpType1Xmt	1.3.6.1.4.1.18.3.5.6.14.20	Counter	read-only	This value counts the number of Type 1 Tarp packets transmitted by this interface.
CTR wfOsiTarpType2Rcv	1.3.6.1.4.1.18.3.5.6.14.21	Counter	read-only	This value counts the number of Type 2 Tarp packets received by this interface.
CTR wfOsiTarpType2Xmt	1.3.6.1.4.1.18.3.5.6.14.22	Counter	read-only	This value counts the number of Type 2 Tarp packets transmitted by this interface.
CTR wfOsiTarpType3Rcv	1.3.6.1.4.1.18.3.5.6.14.23	Counter	read-only	This value counts the number of Type 3 Tarp packets received by this interface.
CTR wfOsiTarpType3Xmt	1.3.6.1.4.1.18.3.5.6.14.24	Counter	read-only	This value counts the number of Type 3 Tarp packets transmitted by this interface.
CTR wfOsiTarpType4Rcv	1.3.6.1.4.1.18.3.5.6.14.25	Counter	read-only	This value counts the number of Type 4 Tarp packets received by this interface.
CTR wfOsiTarpType4Xmt	1.3.6.1.4.1.18.3.5.6.14.26	Counter	read-only	This value counts the number of Type 4 Tarp packets transmitted by this interface.
CTR wfOsiTarpType5Rcv	1.3.6.1.4.1.18.3.5.6.14.27	Counter	read-only	This value counts the number of Type 5 Tarp packets received by this interface.
CTR wfOsiTarpType5Xmt	1.3.6.1.4.1.18.3.5.6.14.28	Counter	read-only	This value counts the number of Type 5 Tarp packets transmitted by this interface.
wfOsiTarpCircuitTable	1.3.6.1.4.1.18.3.5.6.15		not-accessible	This table contains all of the Tarp interfaces for this system.
wfOsiTarpCircuitEntry	1.3.6.1.4.1.18.3.5.6.15.1		not-accessible	This is the Tarp Interface Entry for the Tarp Interface Table.
INT wfOsiTarpCircuitCreate	1.3.6.1.4.1.18.3.5.6.15.1.1	INTEGER	read-write	This value determines if the Tarp Interface is to be created for this OSI interface.
INT wfOsiTarpCircuitEnable	1.3.6.1.4.1.18.3.5.6.15.1.2	INTEGER	read-write	This value determines if the Tarp Interface is to be enabled for this OSI interface.
INT wfOsiTarpCircuitState	1.3.6.1.4.1.18.3.5.6.15.1.3	INTEGER	read-only	This value reflects the state of the Tarp interface.
INT wfOsiTarpCircuitCct	1.3.6.1.4.1.18.3.5.6.15.1.4	INTEGER	read-only	Circuit number for this Tarp Interface.
INT wfOsiTarpCircuitPropagate	1.3.6.1.4.1.18.3.5.6.15.1.5	INTEGER	read-write	This value determines if this interface will propagate transit Tarp packets out this interface.
INT wfOsiTarpCircuitOriginate	1.3.6.1.4.1.18.3.5.6.15.1.6	INTEGER	read-write	This value determines if this interface will send out Tarp packets originated by the router.
CTR wfOsiTarpCircuitType1Rcv	1.3.6.1.4.1.18.3.5.6.15.1.7	Counter	read-only	This value counts the number of Type 1 Tarp packets received by this interface.
CTR wfOsiTarpCircuitType1Xmt	1.3.6.1.4.1.18.3.5.6.15.1.8	Counter	read-only	This value counts the number of Type 1 Tarp packets transmitted by this interface.
CTR wfOsiTarpCircuitType2Rcv	1.3.6.1.4.1.18.3.5.6.15.1.9	Counter	read-only	This value counts the number of Type 2 Tarp packets received by this interface.
CTR wfOsiTarpCircuitType2Xmt	1.3.6.1.4.1.18.3.5.6.15.1.10	Counter	read-only	This value counts the number of Type 2 Tarp packets transmitted by this interface.
CTR wfOsiTarpCircuitType3Rcv	1.3.6.1.4.1.18.3.5.6.15.1.11	Counter	read-only	This value counts the number of Type 3 Tarp packets received by this interface.
CTR wfOsiTarpCircuitType3Xmt	1.3.6.1.4.1.18.3.5.6.15.1.12	Counter	read-only	This value counts the number of Type 3 Tarp packets transmitted by this interface.
CTR wfOsiTarpCircuitType4Rcv	1.3.6.1.4.1.18.3.5.6.15.1.13	Counter	read-only	This value counts the number of Type 4 Tarp packets received by this interface.
CTR wfOsiTarpCircuitType4Xmt	1.3.6.1.4.1.18.3.5.6.15.1.14	Counter	read-only	This value counts the number of Type 4 Tarp packets transmitted by this interface.
CTR wfOsiTarpCircuitType5Rcv	1.3.6.1.4.1.18.3.5.6.15.1.15	Counter	read-only	This value counts the number of Type 5 Tarp packets received by this interface.
CTR wfOsiTarpCircuitType5Xmt	1.3.6.1.4.1.18.3.5.6.15.1.16	Counter	read-only	This value counts the number of Type 5 Tarp packets transmitted by this interface.
CTR wfOsiTarpCircuitNoBufs	1.3.6.1.4.1.18.3.5.6.15.1.17	Counter	read-only	This value represents the number of times Tarp tried to allocate a buffer but was unable.
wfOsiTarpLDBTable	1.3.6.1.4.1.18.3.5.6.16		not-accessible	Table of wfOsiTarpLDBEntry's.
wfOsiTarpLDBEntry	1.3.6.1.4.1.18.3.5.6.16.1		not-accessible	Each entry in the Loop Detection Buffer.
INT wfOsiTarpLDBCreate	1.3.6.1.4.1.18.3.5.6.16.1.1	INTEGER	read-write	Specifies the creation or deletion of the instance.
OCT wfOsiTarpLDBNSAP	1.3.6.1.4.1.18.3.5.6.16.1.2	OCTET STRING	read-only	The NSAP address for this entry.
INT wfOsiTarpLDBSequence	1.3.6.1.4.1.18.3.5.6.16.1.3	INTEGER	read-only	The sequence number for this LDB entry.
INT wfOsiTarpLDBCurrentTimer	1.3.6.1.4.1.18.3.5.6.16.1.4	INTEGER	read-write	Current timer for this LDB Entry.
wfOsiTarpStaticAdjTable	1.3.6.1.4.1.18.3.5.6.17		not-accessible	Table of wfOsiTarpStaticAdjEntry's.
wfOsiTarpStaticAdjEntry	1.3.6.1.4.1.18.3.5.6.17.1		not-accessible	This is the static adjacency record that appears in the adjacency table.
INT wfOsiTarpStaticAdjCreate	1.3.6.1.4.1.18.3.5.6.17.1.1	INTEGER	read-write	This value determines if this instance should be created or deleted.
INT wfOsiTarpStaticAdjEnable	1.3.6.1.4.1.18.3.5.6.17.1.2	INTEGER	read-write	This value determines if the Static Adjacency should be enabled.
OCT wfOsiTarpStaticAdjNSAP	1.3.6.1.4.1.18.3.5.6.17.1.3	OCTET STRING	read-only	This specifies the address of the Static Adjacency. It is also the instance ID.
INT wfOsiTarpStaticNibbleLength	1.3.6.1.4.1.18.3.5.6.17.1.4	INTEGER	read-write	Describes the number of nibbles in the Static NSAP Address.
wfOsiTarpIgnoreAdjTable	1.3.6.1.4.1.18.3.5.6.18		not-accessible	This table contains all the adjacency entries that should be ignored.
wfOsiTarpIgnoreAdjEntry	1.3.6.1.4.1.18.3.5.6.18.1		not-accessible	This is the ignore static route entry for the wfOsiTarpIgnoreAdj table.
INT wfOsiTarpIgnoreAdjCreate	1.3.6.1.4.1.18.3.5.6.18.1.1	INTEGER	read-write	Signifies this instance should be created.
INT wfOsiTarpIgnoreAdjEnable	1.3.6.1.4.1.18.3.5.6.18.1.2	INTEGER	read-write	This value determines if this instance should be enabled or disabled.
OCT wfOsiTarpIgnoreAdjNSAP	1.3.6.1.4.1.18.3.5.6.18.1.3	OCTET STRING	read-only	Identifies the OSI Adjacency that should be ignored.
INT wfOsiTarpIgnoreNibbleLength	1.3.6.1.4.1.18.3.5.6.18.1.4	INTEGER	read-write	Describes the number of nibbles in the Static NSAP Address for the Ignore Static Route.
wfOsiGreAdjTable	1.3.6.1.4.1.18.3.5.6.19		not-accessible	Gre Adjacency Table
wfOsiGreAdjEntry	1.3.6.1.4.1.18.3.5.6.19.1		not-accessible	GRE Adjacency Entry
INT wfOsiGreAdjDelete	1.3.6.1.4.1.18.3.5.6.19.1.1	INTEGER	read-write	Delete/Create parameter.
INT wfOsiGreAdjDisable	1.3.6.1.4.1.18.3.5.6.19.1.2	INTEGER	read-write	Enable/Disable parameter
INT wfOsiGreAdjTnlNum	1.3.6.1.4.1.18.3.5.6.19.1.3	INTEGER	read-only	GRE tunnel number from GRE MIB
INT wfOsiGreAdjConnNum	1.3.6.1.4.1.18.3.5.6.19.1.4	INTEGER	read-only	GRE remote tunnel connection number from GRE MIB.
IP wfOsiGreAdjRemoteISId	1.3.6.1.4.1.18.3.5.6.19.1.5	IpAddress	read-write	This is the Physical IP address of the Destination.
INT wfOsiGreAdjCircuitId	1.3.6.1.4.1.18.3.5.6.19.1.6	INTEGER	read-write	Circuit number on which this link in configured.

RFC description

Manages OSI protocol stack configurations, IS-IS routing parameters, and router type settings on Wellfleet equipment.

Start monitoring Wellfleet/Bay Networks routers, legacy OSI/CLNP routing infrastructure (IS-IS adjacency status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-OSI-MIB

What Is Wellfleet-OSI-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description