Wellfleet-BGP-MIB

All MIBs › Wellfleet-BGP-MIB

Category: Wellfleet BayNetworks Routing Protocols

Description: Monitors Wellfleet BGP peer sessions, route advertisements, and path attribute statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-BGP-MIB?

Wellfleet-BGP-MIB is a proprietary MIB from Wellfleet Communications/Bay Networks that monitors the Border Gateway Protocol (BGP) implementation on its routers. It exposes data on BGP peer sessions, the routes each peer advertises, and path-attribute statistics associated with those routes. As a routing-protocol MIB it is primarily used to monitor software/protocol health: whether a BGP peer session is established, how many prefixes are being received or advertised, and whether route counts or attributes change unexpectedly -- key indicators of routing instability or misconfiguration. It closely parallels (and predates broad adoption of) the standard IETF BGP4-MIB, sharing similar peer-table concepts adapted to Wellfleet's own OID structure. It was typically deployed on Wellfleet/Bay Networks routers acting as BGP speakers at network edges or in ISP/enterprise WAN cores, and administrators can download the Wellfleet-BGP-MIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-BGP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet/Bay Networks router (legacy)

Monitoring Examples

No sample objects were provided, so this is inferred from the description: an administrator would poll the BGP peer table to check each peer's session state and the number of routes received from it. A peer whose session unexpectedly drops from 'established' to 'idle', or whose received-route count suddenly falls to zero, would indicate a BGP session reset or a route-filtering/policy problem needing investigation.

What Can Be Monitored

BGP peer session state
routes advertised/received per peer
path attribute statistics
BGP session state transitions

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfBgpGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfBgpGeneralGroup	1.3.6.1.4.1.18.3.5.3.2.5.1
wfBgp	1.3.6.1.4.1.18.3.5.3.2.5.1.1
INT wfBgpDelete	1.3.6.1.4.1.18.3.5.3.2.5.1.1.1	INTEGER	read-write	Create/Delete parameter for determining whether or not BGP is configured on this router.
INT wfBgpDisable	1.3.6.1.4.1.18.3.5.3.2.5.1.1.2	INTEGER	read-write	Enable/Disable parameter for determining whether or not to allow any versions of BGP to start up.
INT wfBgpState	1.3.6.1.4.1.18.3.5.3.2.5.1.1.3	INTEGER	read-only	the administrative state of BGP
IP wfBgpIdentifier	1.3.6.1.4.1.18.3.5.3.2.5.1.1.4	IpAddress	read-write	The BGP Identifier for this router.
INT wfBgpLocalAs	1.3.6.1.4.1.18.3.5.3.2.5.1.1.5	INTEGER	read-write	The Autonomous System (AS) that this router belongs to.
INT wfBgpEbgpDebugSwitch	1.3.6.1.4.1.18.3.5.3.2.5.1.1.6	INTEGER	read-write	If this debug switch is enabled, BGP will not enforce the rule that requires each EBGP peer to be on a directly attached network.
OCT wfBgpVersion	1.3.6.1.4.1.18.3.5.3.2.5.1.1.7	OCTET STRING	read-only	Vector of supported BGP protocol version numbers. Each peer negotiates the version from this vector. Versions are identified via the string of bits contained within this attribute. The first octet contains bits 0 to 7, the second octet contains bits 8 to 15, and so on, with the most significant bit referring to the lowest bit number in the octet (e.g., the MSB of the first octet refers to bit 0). If a bit, i, is present and set, then the version (i+1) of the BGP is supported.
INT wfBgpIntraAsIbgpRouting	1.3.6.1.4.1.18.3.5.3.2.5.1.1.8	INTEGER	read-write	If this switch is enabled, BGP will perform Intra-AS IBGP routing.
INT wfIbgpFromProtocols	1.3.6.1.4.1.18.3.5.3.2.5.1.1.9	INTEGER	read-write	if Intra-AS IBGP routing is enabled, this attribute spcifies if non-BGP external routes can be propogated via IBGP.
INT wfBgpIntAdvTimer	1.3.6.1.4.1.18.3.5.3.2.5.1.1.10	INTEGER	read-write	the minimum time interval, in seconds, between injections of EBGP routes into the IP routing table. default is 5. Can't be zero
CTR wfBgpUsedRoutes	1.3.6.1.4.1.18.3.5.3.2.5.1.1.11	Counter	read-only	the number of received BGP routes that have been submitted for possible inclusion in the IP routing table.
CTR wfBgpTotalRoutes	1.3.6.1.4.1.18.3.5.3.2.5.1.1.12	Counter	read-only	the total number of BGP routes currently maintained.
CTR wfBgpTotalPaths	1.3.6.1.4.1.18.3.5.3.2.5.1.1.13	Counter	read-only	the total number of BGP path attributes blocks currently maintained.
INT wfBgpMaxRedundantIbgpRoutes	1.3.6.1.4.1.18.3.5.3.2.5.1.1.14	INTEGER	read-write	Specifies the maximum number of IBGP routes to the same destination to be stored. At this point at least one route is stored even if zero is specified. If set to BGP_MAX_REDUNDANT_RTS_MAXIMUM, no limit will be imposed.
INT wfBgpRouteRequestSwitch	1.3.6.1.4.1.18.3.5.3.2.5.1.1.15	INTEGER	read-write	If this switch is enabled and at least one connection to IBGP route server is enabled, alternate routes to a destination which became unreachable will be requested from the Route Server.
INT wfBgpConnCollisionDetect	1.3.6.1.4.1.18.3.5.3.2.5.1.1.16	INTEGER	read-write	If this switch is enabled, redundant BGP connections to the same router will be detected and disallowed, i.e. only one BGP connection to the same router will be maintained.
INT wfBgpRsTopology	1.3.6.1.4.1.18.3.5.3.2.5.1.1.17	INTEGER	read-write	Specifies IBGP Route Server connection topology: none(Non-RS), RC, full-mesh, or tree. To enable Route Server mode full-mesh or tree topology must be selected.
GAU wfBgpClusterIdentifier	1.3.6.1.4.1.18.3.5.3.2.5.1.1.18	Gauge	read-write	If RS Server, cluster Identifer for this server
INT wfBgpDynamicPolChangeSupport	1.3.6.1.4.1.18.3.5.3.2.5.1.1.19	INTEGER	read-write	If this switch is enabled, when a BGP policy rule changes all affected routes are dynamically re-evaluated according to the new policy specification. If this switch is disabled, all bgp connections are restarted.
GAU wfBgpSoloistSlots	1.3.6.1.4.1.18.3.5.3.2.5.1.1.20	Gauge	read-write	Slot mask for which slots BGP is eligible to run on. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. Default is all slots on a BCN.
INT wfBgpSoloistSlot	1.3.6.1.4.1.18.3.5.3.2.5.1.1.21	INTEGER	read-only	Slot on which BGP runs in Soloist mode. Slots can be 1-14. Zero means that BGP is not in a Soloist mode. Default is zero.
INT wfBgpSubnetAggregation	1.3.6.1.4.1.18.3.5.3.2.5.1.1.22	INTEGER	read-write	If this switch is enabled, non-BGP originated subnet routes are aggregated to their corresponding natural network routes for advertisement to bgp peers. Advertisement of BGP originated routes is not affected by this switch.
INT wfBgpBlackHoleSupport	1.3.6.1.4.1.18.3.5.3.2.5.1.1.23	INTEGER	read-write	If this switch is disabled BGP doesn't submit a 'black-hole' route into IP routing table for an aggregate route advertised to a BGP peer. For action 'drop' packet will be dropped and for 'reject' - 'ICMP Destination Unreachable' will be send back.
INT wfBgpMedComparison	1.3.6.1.4.1.18.3.5.3.2.5.1.1.24	INTEGER	read-write	If this switch is disabled BGP, the Multi-Exit Discriminator (MED) route attribute is not considered in the route selection process.
INT wfBgpIbgpReflection	1.3.6.1.4.1.18.3.5.3.2.5.1.1.25	INTEGER	read-write	Enables/Disables reflecting of BGP routes to IBGP peers.
INT wfBgpIbgpEcmpMethod	1.3.6.1.4.1.18.3.5.3.2.5.1.1.26	INTEGER	read-write	Method to use IGP ECMP routing information for an IBGP peering. route-balance method distributes a set of destination networks that share the same IBGP Next Hop among available ECMP routes. Each IBGP network has one route submitted to IP RTM. traffic-balance uses all avaiable IGP ECMP routes. Each IBGP network submitted to IP RTM number of times equal to number IGP ECMP routes to IBGP Next Hop.
INT wfBgpLocalPrefCalc	1.3.6.1.4.1.18.3.5.3.2.5.1.1.27	INTEGER	read-write	Enable/disable local_pref calculation
INT wfBgpConfedIdentifier	1.3.6.1.4.1.18.3.5.3.2.5.1.1.28	INTEGER	read-write	The BGP Confederation Identifier for this router. NIL means this AS is not a member of any confederation
OCT wfBgpConfedPeers	1.3.6.1.4.1.18.3.5.3.2.5.1.1.29	OCTET STRING	read-write	Peer list of this BGP speaker to other member sub_ASs within the same confederation, NIL means no peer from this speaker to neighbor ASs that are members of this local confederation
INT wfBgpIgpInterAction	1.3.6.1.4.1.18.3.5.3.2.5.1.1.30	INTEGER	read-write	Bit map for BGP/IGP interaction control: bit 15 bit 0 +---------------------------------------+ \| \| +---------------------------------------+ bit0: eBGP to OSPF bit1: eBGP to RIP bit2 - bit15: Reserved value 0 means no interaction
wfBgpPeerTable	1.3.6.1.4.1.18.3.5.3.2.5.1.2		not-accessible	The BGP Peer table contains configuration and statistical information regarding this router's BGP peers
wfBgpPeerEntry	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1		not-accessible	An entry in the BGP-Peer table
INT wfBgpPeerDelete	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.1	INTEGER	read-write	Create/Delete: if set to delete, the peer connection is removed
INT wfBgpPeerDisable	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.2	INTEGER	read-write	Enable/Disable: controls whether the peer connection is enabled or disabled
INT wfBgpPeerState	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.3	INTEGER	read-only	the administrative state of the peer connection on this interface
IP wfBgpPeerLocalAddr	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.4	IpAddress	read-only	the local interface address
INT wfBgpPeerLocalPort	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.5	INTEGER	read-only	the local TCP port number
IP wfBgpPeerRemoteAddr	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.6	IpAddress	read-only	the peer's interface address
INT wfBgpPeerRemotePort	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.7	INTEGER	read-only	the peer's TCP port number
INT wfBgpPeerMinVersion	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.8	INTEGER	read-write	the minimum BGP version number supported on this connection. Default is 4.
INT wfBgpPeerMaxVersion	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.9	INTEGER	read-write	the maximum BGP version number supported on this connection Default is 4.
INT wfBgpPeerRemoteAs	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.10	INTEGER	read-write	the configured peer's AS number. this must be filled in. the AS received in the open message must match this one.
INT wfBgpPeerExtAdvTimer	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.11	INTEGER	read-write	Time interval in seconds for the MinRouteAdvertisementInterval BGP timer. Default is 30. Can't be zero
INT wfBgpPeerConnectRetry	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.12	INTEGER	read-write	the ConnectRetry timer, in seconds. this is the time between TCP connection attempts.
INT wfBgpPeerCfgHoldtime	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.13	INTEGER	read-write	the configured Holdtime timer, in seconds. this is the maximum time that the peer can wait without receiving a KEEPALIVE from this speaker. if no hold timer is to be used (for an SVC), zero should be entered. otherwise, the value must be 3 or greater. this value is sent in the OPEN message. upon receipt of an OPEN, the received hold time is compared to this value. if both are zero, no hold timer will be run and periodic keepalives will not be sent. otherwise, the minimum of the two timers will be used. if this results in a hold timer of less than 3, 3 will be used.
INT wfBgpPeerHoldtime	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.14	INTEGER	read-only	the Holdtime timer value that was negotiated and is in use
INT wfBgpPeerCfgKeepAlive	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.15	INTEGER	read-write	the configured KeepAlive timer, in seconds. this is the interval between sending KEEPALIVE messages. if the hold timer was set to zero, this is ignored. otherwise, the KeepAlive timer will be set to the minimum of this value and 1/3 of the hold timer.
INT wfBgpPeerKeepAlive	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.16	INTEGER	read-only	the value used for the KeepAlive timer
INT wfBgpPeerPathAttrSwitch	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.17	INTEGER	read-write	controls whether the wfBgp3PathAttrTable (and the bgpRcvdPathAttrTable) will be maintained.
IP wfBgpPeerIdentifier	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.18	IpAddress	read-only	the BGP ID of the Peer
INT wfBgpPeerConnState	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.19	INTEGER	read-only	the state of the BGP connection FSM
INT wfBgpPeerNegotiatedVersion	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.20	INTEGER	read-only	the negotiated version of BGP running between the two peers
CTR wfBgpPeerInUpdates	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.21	Counter	read-only	the number of BGP UPDATE messages received on this connection. This object should be initialized to zero when the connection is established.
CTR wfBgpPeerOutUpdates	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.22	Counter	read-only	the number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero when the connection is established.
CTR wfBgpPeerInTotalMessages	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.23	Counter	read-only	the total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established.
CTR wfBgpPeerOutTotalMessages	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.24	Counter	read-only	the total number of messages transmitted from the remote peer on this connection. This object should be initialized to zero when the connection is established.
OCT wfBgpPeerLastError	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.25	OCTET STRING	read-only	the last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code; the second contains the subcode.
CTR wfBgpPeerTotalRoutes	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.26	Counter	read-only	the total number of routes that were received from this peer that we are currently maintaining.
CTR wfBgpPeerFsmEstablishedTransitions	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.27	Counter	read-only	The total number of times the BGP FSM transitioned into the established state.
GAU wfBgpPeerFsmEstablishedTime	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.28	Gauge	read-only	This timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set to zero when a new peer is configured or the router is booted.
GAU wfBgpPeerInUpdateElapsedTime	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.29	Gauge	read-only	Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time wfBgpPeerInUpdates is incremented, the value of this object is set to zero (0).
INT wfBgpPeerMinASOriginationInterval	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.30	INTEGER	read-write	Time interval in seconds for the MinASOriginationInterval timer. The default value for this timer is 15 seconds. Can't be zero.
INT wfBgpPeerLocalAS	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.31	INTEGER	read-write	If configured, specifies the AS Number that is sent in OPEN message to this peer. If zero, the AS Number specified with wfBgpLocalAS attribute is used.
INT wfBgpPeerMaxUpdateSize	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.32	INTEGER	read-write	Specifies the maximum size (in bytes) of UPDATE message that can be sent to this peer. Note that, if the message size that is needed to advertise a single route is greater than the configured maximum message size, the acctual message size can exceed the configured value.
INT wfBgpPeerRouteEchoSwitch	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.33	INTEGER	read-write	The switch controls route echoing. If enabled, a BGP route that is selected for forwarding is advertised back to the peer from which the route was received.
INT wfBgpPeerDiscardDuplicateRouteSwitch	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.34	INTEGER	read-write	Indicates if duplicate routes with the identical path attributes should be discarded. Should be enabled only when peering with an IBGP Route Server.
INT wfBgpPeerRSMode	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.35	INTEGER	read-write	Indicates the Route Reflector / Route Server Mode of BGP peer: (1) - not a Route Server or Route Reflector connection; (2) - peer is a Route Server client; (3) - peer is a Route Server in the same RS cluster; (4) - peer is a Route Server in a different RS cluster; (5) - peer is a Route Reflector client; (6) - peer is a Route Reflector in the same RR cluster; (7) - peer is a Route Reflector in a different RR cluster.
INT wfBgpPeerRSIdentifier	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.36	INTEGER	read-write	if wfBgpPeerRSMode is BGP_PEER_RS_MODE_INTERNAL or BGP_PEER_RS_MODE_RS_EXTERNAL, specifies the RS Identifier that is send in IDENTIFICATION message.
INT wfBgpPeerCfgDelayGranularity	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.37	INTEGER	read-write	the configured delay granularity in seconds.
INT wfBgpPeerDelayGranularity	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.38	INTEGER	read-only	the delay granularity in use
INT wfBgpPeerLastErrorSrc	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.39	INTEGER	read-only	The source of the last error notification received/sent \ ( 1 = recv / 2 = sent ). A null is present if no errors \ have occured.
INT wfBgpPeerNexthopSelf	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.40	INTEGER	read-write	Disable the use of third party advertisements
INT wfBgpPeerASLoopDetect	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.41	INTEGER	read-write	Designates whether the router will kill a peering \ session if a Loop is detected in the AS Path.
INT wfBgpPeerBgpEcmpMethod	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.42	INTEGER	read-write	Defines a method to use IGP ECMP routing information. route-balance method distributes a set of destination networks that share the same BGP Next Hop among available ECMP routes. Each BGP network has one route submitted to IP RTM. traffic-balance uses all avaiable IGP ECMP routes. Each BGP network submitted to IP RTM number of times equal to number IGP ECMP routes to BGP Next Hop. This parameter is similar to wfBgpIbgpEcmpMethod but is applicable only to EBGP peer connections. IBGP peer connection selects ECMP method according to wfBgpIbgpEcmpMethod value.
INT wfBgpPeerDampenedRoutes	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.43	INTEGER	read-only	Number of routes from this peer that are suppressed due to flap dampening.
INT wfBgpPeerTTL	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.44	INTEGER	read-write	Configurable Time-To-Live field to be used for this peer connection. Unless wfBgpEbgpDebugSwitch is set, a TTL of 1 is used for external BGP connections. A value of zero (default) indicate to use wfIpBaseDefaultTTL as the TTL value for this peer connection.
INT wfBgpPeerTcpAuthentication	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.45	INTEGER	read-write	Indicates if BGP TCP Authentication is enabled\ none(1) - no authentication\ md5(2) - MD5 authentication enabled
INT wfBgpPeerTcpMd5KeyStorage	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.46	INTEGER	read-write	Indicates how the wfBgpPeerTcpMd5Key is stored \ in the MIB and configuration file. \ clear-text(1) - the key is stored unencrypted \ encrypted(2) - the key is stored encrypted
OCT wfBgpPeerTcpMd5Key	1.3.6.1.4.1.18.3.5.3.2.5.1.2.1.47	OCTET STRING	read-write	if nil, no key configured\ if not nil, BGP TCP MD5 authentication key stored in \ wfBgpPeerTcpMd5KeyStorage format
wfBgpAsWeightTable	1.3.6.1.4.1.18.3.5.3.2.5.1.3		not-accessible	The BGP AS weight table contains weights for autonomous systems for use in best-route calculations
wfBgpAsWeightEntry	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1		not-accessible	An entry in the BGP AS weight table
INT wfBgpAsWeightDelete	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.1	INTEGER	read-write	Create/Delete: if set to delete, the AS entry is removed from this table
INT wfBgpAsWeightDisable	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.2	INTEGER	read-write	Enable/Disable: controls whether the AS entry is enabled or disabled
INT wfBgpAsWeightState	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.3	INTEGER	read-only	the state of this AS weight entry
INT wfBgpAsWeightNumber	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.4	INTEGER	read-only	the AS number
INT wfBgpAsWeightValue	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.5	INTEGER	read-write	the class-1 value to assign to this AS
INT wfBgpAsWeightValue2	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.6	INTEGER	read-write	the class-2 value to assign to this AS
INT wfBgpAsWeightValue3	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.7	INTEGER	read-write	the class-3 value to assign to this AS
INT wfBgpAsWeightValue4	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.8	INTEGER	read-write	the class-4 value to assign to this AS
INT wfBgpAsWeightValue5	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.9	INTEGER	read-write	the class-5 value to assign to this AS
INT wfBgpAsWeightValue6	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.10	INTEGER	read-write	the class-6 value to assign to this AS
INT wfBgpAsWeightValue7	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.11	INTEGER	read-write	the class-7 value to assign to this AS
INT wfBgpAsWeightValue8	1.3.6.1.4.1.18.3.5.3.2.5.1.3.1.12	INTEGER	read-write	the class-8 value to assign to this AS
wfBgpPathAttrTable	1.3.6.1.4.1.18.3.5.3.2.5.1.4		not-accessible	The BGP received path attribute table contains information about paths to destination networks received by all peers.
wfBgpPathAttrEntry	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1		not-accessible	An entry in the BGP Path Attribute Table
IP wfBgpPathAttrIpAddrPrefix	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.1	IpAddress	read-only	the IP address of the destination (sub)network.
INT wfBgpPathAttrIpAddrPrefixLen	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.2	INTEGER	read-only	Length in bits of the IP address prefix in the destination (sub)network address.
IP wfBgpPathAttrPeer	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.3	IpAddress	read-only	the IP address of the peer where the path information was learned.
INT wfBgpPathAttrOrigin	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.4	INTEGER	read-only	the ultimate origin of the path information: igp (1) -- network is interior; egp (2) -- network learned via EGP; incomplete (3) -- undetermined.
OCT wfBgpPathAttrASPathSegment	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.5	OCTET STRING	read-only	The sequence of AS path segments. Each AS path segment is represented by a triple . The type is a 1-octet field which has two possible values: 1 AS_SET: unordered set of ASs a route in the UPDATE message has traversed 2 AS_SEQUENCE: ordered set of ASs a route in the UPDATE message has traversed. The length is a 1-octet field containing the number of ASs in the value field. The value field contains one or more AS numbers, each AS is represented in the octet string as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;
IP wfBgpPathAttrNextHop	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.6	IpAddress	read-only	the address of the border router that should be used as the next-hop for the destination network.
INT wfBgpPathAttrMultiExitDisc	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.7	INTEGER	read-only	The optional inter-AS metric. If this attribute has not been provided for this route, the value for this object is -1.
INT wfBgpPathAttrLocalPref	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.8	INTEGER	read-only	the originating BGP speaker's degree of preference for advertised route (-1..2147483647); if this attribute has not been provided for this route, the value for this object is -1.
INT wfBgpPathAttrAtomicAggregate	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.9	INTEGER	read-only	indicates whether or not the local system has selected a less specific route without selecting a more specific route
INT wfBgpPathAttrAggregatorAS	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.10	INTEGER	read-only	The AS number of the last BGP speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute.
IP wfBgpPathAttrAggregatorAddr	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.11	IpAddress	read-only	The BGP ID of the last BGP speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
INT wfBgpPathAttrCalcLocalPref	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.12	INTEGER	read-only	The degree of preference calculated by the receiving BGP speaker for an advertised route (-1..2147483647). A value of -1 indicates the absence of this attribute
INT wfBgpPathAttrBest	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.13	INTEGER	read-only	an indication of whether or not this was chosen as the best bgp rout to the destination and whether or not it was chosen as a forwarding IP route
OCT wfBgpPathAttrUnknown	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.14	OCTET STRING	read-only	One or more path attributes not understood by this BGP speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size (255), if any, are not recorded by this object.
IP wfBgpPathAttrImporterID	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.15	IpAddress	read-only	For RS, the BGP ID of the border router that imported this route
OCT wfBgpPathAttrClusterID	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.16	OCTET STRING	read-only	For RS, the sequence of Cluter IDs of the Clusters. Size zero (0) indicates the absence of such attribute(s).
OCT wfBgpPathAttrCommunity	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.17	OCTET STRING	read-only	List of BGP communities. Each community is 4 bytes long. Size zero (0) indicates the absence of community attribute. Octets beyond the maximum size (255), if any, are not recorded by this object.
INT wfBgpPathAttrCalcMED	1.3.6.1.4.1.18.3.5.3.2.5.1.4.1.18	INTEGER	read-only	The Multi Exit Disc. calculated by the receiving BGP speaker for an advertised route (-1...2G)
wfBgpDbgTable	1.3.6.1.4.1.18.3.5.3.2.5.1.5		not-accessible	BGP debug table contains objects that controls generation of BGP debug information
wfBgpDbgEntry	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1		not-accessible	a table entry
INT wfBgpDbgCreate	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.1	INTEGER	read-write	Create/Delete parameter. Default is created.
IP wfBgpDbgLocAddr	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.2	IpAddress	read-only	The peer's local address. If 0.0.0.0, debug attributes are applied to all peers to specified Remote Address or with specified BGP version
IP wfBgpDbgRemoteAddr	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.3	IpAddress	read-write	The peer's Remote Address . If 0.0.0.0, debug attrubutes are applied to all configured peers from specified Local Address; if 255.255.255.255, debug attrubutes are applied to BGP4 gate only.
INT wfBgpDbgMsgLevel	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.4	INTEGER	read-write	BGP log messages level. To control certain level of log messages BGP_DBG_MSG_ALL 0x001f0000 - 2031616 BGP_DBG_MSG_DEBUG 0x00010000 - 65536 BGP_DBG_MSG_INFO 0x00020000 - 131072 BGP_DBG_MSG_WARNING 0x00040000 - 262144 BGP_DBG_MSG_FAULT 0x00080000 - 524288 BGP_DBG_MSG_TRACE 0x00100000 - 1048576
INT wfBgpDbgMsgTraceSwitch	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.5	INTEGER	read-write	controls whether BGP messages that are exchanged on this connection are dumped to the log. BGP_DBG_MSG_DUMP_REC_OPEN enables tracing of OPEN messages BGP_DBG_MSG_DUMP_REC_UPDATE - UPDATE messages BGP_DBG_MSG_DUMP_REC_NOTIFICATION - NOTIFICATION and BGP_DBG_MSG_DUMP_REC_KEEPALIVE - KEEPALIVE on logical OR basis BGP_DBG_MSG_DUMP_DISABLED 1 BGP_DBG_MSG_DUMP_REC_OPEN 0x10 - 16 BGP_DBG_MSG_DUMP_REC_UPDATE 0x20 - 32 BGP_DBG_MSG_DUMP_REC_NOTIFICATION 0x40 - 64 BGP_DBG_MSG_DUMP_REC_KEEPALIVE 0x80 - 128
INT wfBgpDbgLogCode	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.6	INTEGER	read-write	Indicates that a debug log message which corresponds to the value of this attributes should be or should be not sent to the log. Affects wfBgpDbgCodes only. In order to save combined list of messages you have to set wfBgpDbgBootCodes directly as copy of wfBgpDbgCodes
INT wfBgpDbgLogCodeDisable	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.7	INTEGER	read-write	Indicates that a debug log message defined in wfBgpDbgCode will be or will be not logged
OCT wfBgpDbgCodes	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.8	OCTET STRING	read-only	Vector of enabled debug messages (to check only). Messages are identified via the string of bits contained within this attribute. The first octet contains bits 0 to 7, the second octet contains bits 8 to 15, and so on, with the most significant bit referring to the lowest bit number in the octet (e.g., the MSB of the first octet refers to bit 0). If a bit, i, is present and set, then the DEBUG log message with the code (i) is enabled.
OCT wfBgpDbgBootCodes	1.3.6.1.4.1.18.3.5.3.2.5.1.5.1.9	OCTET STRING	read-write	User-defined vector of enabled debug messages at boot moment. Coded as instance above
wfBgpVirtualPeerTable	1.3.6.1.4.1.18.3.5.3.2.5.1.6		not-accessible	The BGP Virtual Peer table contains configuration and statistical information regarding this router's Virtual peers learned via the Route Server
wfBgpVirtualPeerEntry	1.3.6.1.4.1.18.3.5.3.2.5.1.6.1		not-accessible	An entry in the BGP-Virtual-Peer table
IP wfBgpVirtualPeerLocalAddr	1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.1	IpAddress	read-only	the local interface address
IP wfBgpVirtualPeerRemoteAddr	1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.2	IpAddress	read-only	the peer's interface address
IP wfBgpVirtualPeerIdentifier	1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.3	IpAddress	read-only	the BGP ID of the Peer
CTR wfBgpVirtualPeerInUpdates	1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.4	Counter	read-only	the number of BGP UPDATE messages received on this connection. This object should be initialized to zero when the connection is established.
CTR wfBgpVirtualPeerTotalRoutes	1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.5	Counter	read-only	the total number of routes that were received from this peer that we are currently maintaining.
GAU wfBgpVirtualPeerInUpdateElapsedTime	1.3.6.1.4.1.18.3.5.3.2.5.1.6.1.6	Gauge	read-only	Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time wfBgpVirtualPeerInUpdates is incremented, the value of this object is set to zero (0).
wfBgpPathAttributeTable	1.3.6.1.4.1.18.3.5.3.2.5.1.7		not-accessible	The BGP received path attribute table contains information about paths to destination networks received by all peers.
wfBgpPathAttributeEntry	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1		not-accessible	An entry in the BGP Path Attribute Table
IP wfBgpPathAttributeIpAddrPrefix	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.1	IpAddress	read-only	the IP address of the destination (sub)network.
INT wfBgpPathAttributeIpAddrPrefixLen	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.2	INTEGER	read-only	Length in bits of the IP address prefix in the destination (sub)network address.
IP wfBgpPathAttributeImporterID	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.3	IpAddress	read-only	For RS, the BGP ID of the border router that imported this route
IP wfBgpPathAttributePeer	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.4	IpAddress	read-only	the IP address of the peer where the path information was learned.
INT wfBgpPathAttributeOrigin	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.5	INTEGER	read-only	the ultimate origin of the path information: igp (1) -- network is interior; egp (2) -- network learned via EGP; incomplete (3) -- undetermined.
OCT wfBgpPathAttributeASPathSegment	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.6	OCTET STRING	read-only	The sequence of AS path segments. Each AS path segment is represented by a triple . The type is a 1-octet field which has two possible values: 1 AS_SET: unordered set of ASs a route in the UPDATE message has traversed 2 AS_SEQUENCE: ordered set of ASs a route in the UPDATE message has traversed. The length is a 1-octet field containing the number of ASs in the value field. The value field contains one or more AS numbers, each AS is represented in the octet string as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;
IP wfBgpPathAttributeNextHop	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.7	IpAddress	read-only	the address of the border router that should be used as the next-hop for the destination network.
INT wfBgpPathAttributeMultiExitDisc	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.8	INTEGER	read-only	The optional inter-AS metric. If this attribute has not been provided for this route, the value for this object is -1.
INT wfBgpPathAttributeLocalPref	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.9	INTEGER	read-only	the originating BGP speaker's degree of preference for advertised route (-1..2147483647); if this attribute has not been provided for this route, the value for this object is -1.
INT wfBgpPathAttributeAtomicAggregate	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.10	INTEGER	read-only	indicates whether or not the local system has selected a less specific route without selecting a more specific route
INT wfBgpPathAttributeAggregatorAS	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.11	INTEGER	read-only	The AS number of the last BGP speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute.
IP wfBgpPathAttributeAggregatorAddr	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.12	IpAddress	read-only	The BGP ID of the last BGP speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
INT wfBgpPathAttributeCalcLocalPref	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.13	INTEGER	read-only	The degree of preference calculated by the receiving BGP speaker for an advertised route (-1..2147483647). A value of -1 indicates the absence of this attribute
INT wfBgpPathAttributeBest	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.14	INTEGER	read-only	an indication of whether or not this was chosen as the best bgp rout to the destination and whether or not it was chosen as a forwarding IP route
OCT wfBgpPathAttributeUnknown	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.15	OCTET STRING	read-only	One or more path attributes not understood by this BGP speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size (255), if any, are not recorded by this object.
OCT wfBgpPathAttributeClusterID	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.16	OCTET STRING	read-only	For RS, the sequence of Cluter IDs of the Clusters. Size zero (0) indicates the absence of such attribute(s).
OCT wfBgpPathAttributeCommunity	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.17	OCTET STRING	read-only	List of BGP communities. Each community is 4 bytes long. Size zero (0) indicates the absence of community attribute. Octets beyond the maximum size (255), if any, are not recorded by this object.
INT wfBgpPathAttributeCalcMED	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.18	INTEGER	read-only	The Multi Exit Disc. calculated by the receiving BGP speaker for an advertised route (-1...2G)
INT wfBgpPathAttributeFlapPenalty	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.19	INTEGER	read-only	Penalty value based on number of route flaps
INT wfBgpPathAttributeFlapCount	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.20	INTEGER	read-only	Number of times a route flapped since the last time the penaltywas reset to zero
INT wfBgpPathAttributeRouteDampened	1.3.6.1.4.1.18.3.5.3.2.5.1.7.1.21	INTEGER	read-only	Shows whether this route is currently suppressed from being announced
wfBgpRouteFlapDampeningTable	1.3.6.1.4.1.18.3.5.3.2.5.1.8		not-accessible	Table of wfBgpRouteFlapDampeningEntry
wfBgpRouteFlapDampeningEntry	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1		not-accessible	An entry in the Route Flap Dampening table
INT wfBgpRouteFlapDampeningDelete	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.1	INTEGER	read-write	Create/Delete: if set to delete, the entry is removed
INT wfBgpRouteFlapDampeningIndex	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.2	INTEGER	read-only	Index number of this entry in wfBgpRouteFlapDampeningTable
STR wfBgpRouteFlapDampeningName	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.3	DisplayString	read-write	Name of this template
INT wfBgpRouteFlapDampeningCutoffThreshold	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.4	INTEGER	read-write	Value of penalty over which a route is suppressed. Expressed in number of withdrawals
INT wfBgpRouteFlapDampeningReuseThreshold	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.5	INTEGER	read-write	Value of penalty below which a route is unsuppressed. Expressed in number of withdrawals
INT wfBgpRouteFlapDampeningReachableDecay	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.6	INTEGER	read-write	Duration in minutes after which the penalty value is reduced to half when the route is reachable. Default is 5 minutes
INT wfBgpRouteFlapDampeningUnreachableDecay	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.7	INTEGER	read-write	Duration in minutes after which the penalty value is reduced to half when the route is unreachable. Default is 15 minutes.
INT wfBgpRouteFlapDampeningMaxHoldDown	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.8	INTEGER	read-write	Maximum time a route remains suppressed. Expressed in number seconds. Default is 45 minutes
INT wfBgpRouteFlapDampeningMemoryLimit	1.3.6.1.4.1.18.3.5.3.2.5.1.8.1.9	INTEGER	read-write	If the state of a route(reachable/unreachable) remains stable for this duration, the penalty is cleared and the route unsuppressed. Expressed in number of minutes. Default is 45 minutes
wfBgp3Group	1.3.6.1.4.1.18.3.5.3.2.5.2
wfBgp3	1.3.6.1.4.1.18.3.5.3.2.5.2.1
INT wfBgp3Delete	1.3.6.1.4.1.18.3.5.3.2.5.2.1.1	INTEGER	read-write	Create/Delete parameter for determining whether or not BGP3 is configured on this router.
INT wfBgp3Disable	1.3.6.1.4.1.18.3.5.3.2.5.2.1.2	INTEGER	read-write	Enable/Disable parameter for determining whether or not to start-up BGP3.
INT wfBgp3State	1.3.6.1.4.1.18.3.5.3.2.5.2.1.3	INTEGER	read-only	the administrative state of BGP-3
INT wfBgp3IntraAsIbgpRouting	1.3.6.1.4.1.18.3.5.3.2.5.2.1.4	INTEGER	read-write	If this switch is enabled, BGP-3 will perform Intra-AS IBGP routing.
INT wfBgp3IntAdvTimer	1.3.6.1.4.1.18.3.5.3.2.5.2.1.5	INTEGER	read-write	the minimum time interval, in seconds, between injections of EBGP routes into the IP routing table. default is 5. can't be zero
INT wfBgp3RipRules	1.3.6.1.4.1.18.3.5.3.2.5.2.1.6	INTEGER	read-write	if enabled, IBGP routes that are also reachable via a RIP route will be consider 'reachable' and will be used. the use of this is highly discouraged.
CTR wfBgp3UsedRoutes	1.3.6.1.4.1.18.3.5.3.2.5.2.1.7	Counter	read-only	the number of received BGP-3 routes that have been submitted for possible inclusion in the IP routing table.
CTR wfBgp3TotalRoutes	1.3.6.1.4.1.18.3.5.3.2.5.2.1.8	Counter	read-only	the total number of BGP-3 routes currently maintained.
wfBgp3PathAttrTable	1.3.6.1.4.1.18.3.5.3.2.5.2.2		not-accessible	The BGP3 received path attribute table contains information about paths to destination networks received by all peers. This table is deprecated and replaced with wfBgpPathAttrTable
wfBgp3PathAttrEntry	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1		not-accessible	An entry in the BGP-3 Path Attribute Table
IP wfBgp3PathAttrPeer	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.1	IpAddress	read-only	the BGP identifier of the peer where the path information was learned.
IP wfBgp3PathAttrDestNetwork	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.2	IpAddress	read-only	the address of the destination network.
INT wfBgp3PathAttrOrigin	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.3	INTEGER	read-only	the ultimate origin of the path information: igp (1) -- network is interior; egp (2) -- network learned via EGP; incomplete (3) -- undetermined.
OCT wfBgp3PathAttrASPath	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.4	OCTET STRING	read-only	the set of ASes that must be traversed to reach the network. Each AS is represented as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;
IP wfBgp3PathAttrNextHop	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.5	IpAddress	read-only	the address of the border router that should be used as the next-hop for the destination network.
INT wfBgp3PathAttrInterASMetric	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.6	INTEGER	read-only	the optional inter-AS metric. if this attribute has not been provided for this route, the value for this object is 0.
INT wfBgp3PathAttrASPathWeight	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.7	INTEGER	read-only	the calculated AS path weight
INT wfBgp3PathAttrBgpPreference	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.8	INTEGER	read-only	the preference that is used to calculate this route with other BGP routes to the same destination
INT wfBgp3PathAttrBest	1.3.6.1.4.1.18.3.5.3.2.5.2.2.1.9	INTEGER	read-only	an indication of whether or not this was chosen as the best route to the destination
wfBgp4Group	1.3.6.1.4.1.18.3.5.3.2.5.3
wfBgp4	1.3.6.1.4.1.18.3.5.3.2.5.3.1
INT wfBgp4Delete	1.3.6.1.4.1.18.3.5.3.2.5.3.1.1	INTEGER	read-write	Create/Delete parameter for determining whether or not BGP-4 is configured on this router.
INT wfBgp4Disable	1.3.6.1.4.1.18.3.5.3.2.5.3.1.2	INTEGER	read-write	Enable/Disable parameter for determining whether or not to start-up BGP-4.
INT wfBgp4State	1.3.6.1.4.1.18.3.5.3.2.5.3.1.3	INTEGER	read-only	the administrative state of BGP-4

RFC description

Wellfleet Communications vendor-private MIB for BGP (Border Gateway Protocol) management on Wellfleet routers.

Start monitoring Wellfleet/Bay Networks router, legacy (BGP peer-session/prefix-count status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-BGP-MIB

What Is Wellfleet-BGP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description