Wellfleet-DCMMW-MIB

All MIBs › Wellfleet-DCMMW-MIB

Category: Wellfleet BayNetworks System Management

Description: Manages Wellfleet data compression middleware parameters and compression ratio statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-DCMMW-MIB?

Wellfleet-DCMMW-MIB is a legacy Wellfleet/Bay Networks proprietary MIB (built on the shared Wellfleet-COMMON-MIB SMI) implementing DCMMW (a dynamically-loaded RMON-monitoring-card module) on Wellfleet/Bay Networks routers. Its objects cover delete/disable/create controls, boot image name/option/save-mode, config mode, RMON max-host/default-host/default-matrix settings, and a per-DCM-card table reporting memory size, hardware/firmware revision, agent image version, operational status, and stream count, following the vendor's standard create/delete/disable pattern for dynamically-loaded software modules. As a configuration/status MIB it lets an administrator confirm whether DCMMW (a dynamically-loaded RMON-monitoring-card module) is loaded/enabled and audit its configuration. It is deployed on legacy Wellfleet/Bay Networks routers. Engineers can download the Wellfleet-DCMMW-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-DCMMW-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Legacy Wellfleet/Bay Networks routers

Monitoring Examples

An administrator checks whether DCMMW (a dynamically-loaded RMON-monitoring-card module) has been created and enabled on a legacy Wellfleet router before troubleshooting a feature that depends on it.

What Can Be Monitored

DCMMW (a dynamically-loaded RMON-monitoring-card module) load/enable state and configuration

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfDCMmwGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfDCMmw	1.3.6.1.4.1.18.3.3.2.16.1
INT wfDCMmwDelete	1.3.6.1.4.1.18.3.3.2.16.1.1	INTEGER	read-write	DCMMW is dynamically loaded. This object specifies that the users can perform a set operation on this object in order to create/delete DCMMW base record. Default is created.
INT wfDCMmwDisable	1.3.6.1.4.1.18.3.3.2.16.1.2	INTEGER	read-write	Enables or Disables DCMMW Subsystem. By disabling DCMMW, can disable the DCM board.
STR wfDCMmwImageName	1.3.6.1.4.1.18.3.3.2.16.1.3	DisplayString	read-write	A textual string to describe the name of DCM image to be download on to DCM. The image name should be a fully qualified filename. For ex: vol:filename.
INT wfDCMmwBootOption	1.3.6.1.4.1.18.3.3.2.16.1.4	INTEGER	read-write	Specifies DCM's image load mode to DCMMW. If the option specified is local, DCMMW will not load a new image to DCM's shared memory. If the option specified is download, then DCMMW will load an image into DCM's shared memory. Name of the image is specified using wfDCMMWImageName
INT wfDCMmwImageSaveMode	1.3.6.1.4.1.18.3.3.2.16.1.5	INTEGER	read-write	Specifies DCM's image save mode. If the mode is save, then DCMMW indicates it to DCM, to save the image on to its(DCM's) FLASH memory. This saved image will be used by DCM in its next boot time if the boot option is set to local. If the mode is nosave then the image will not be saved.
INT wfDCMmwCfgMode	1.3.6.1.4.1.18.3.3.2.16.1.6	INTEGER	read-write	Specifies whether DCMMW should let DCM use the config info from the shared memory or use the config info from DCM's FLASH memory. If the mode is local, then DCMMW will write `0' in DCM's config file, which indicates the DCM that it should use the config info from its FLASH memory. If the mode is shared memory, then DCMMW will write the config info in DCM's config file, for DCM to use.
INT wfDCMmwWriteConfigInfo	1.3.6.1.4.1.18.3.3.2.16.1.7	INTEGER	read-write	DCMMW uses this object to specify DCM whether it should commit the configuration information into its Flash memory or not
INT wfDCMmwRMONMaxHost	1.3.6.1.4.1.18.3.3.2.16.1.8	INTEGER	read-write	Indicates the maximum number of hosts each RMON host control entry on DCM will store. When the table reaches this value, entries will be deleted based on an LRU algorithm. The max limit depends on the amount of memory installed in DCM. It is in the range 2048..8128. DCMMW uses this object to provide the value to DCM. Check the MIB object wfDCMmwRMONHost to verify the number of hosts that got configured in the RMON host control entry.
INT wfDCMmwRMONDfltHost	1.3.6.1.4.1.18.3.3.2.16.1.9	INTEGER	read-write	DCMMW uses this to specify DCM that it should create or not create the hostControlTable. If enabled DCMMW indicates DCM to create default host entries for the interface it is configured to.
INT wfDCMmwRMONDfltMtrix	1.3.6.1.4.1.18.3.3.2.16.1.10	INTEGER	read-write	DCMMW uses this to specify DCM that it should create or not create the matrixControlTable. If enabled DCMMW indicates DCM to create default matrix entries for the interface it is configured to.
INT wfDCMmwRMONHost	1.3.6.1.4.1.18.3.3.2.16.1.11	INTEGER	read-only	This specifies the configured number of hosts in each RMON host control entry on DCM
INT wfDCMRmonAgent	1.3.6.1.4.1.18.3.3.2.16.1.12	INTEGER	read-only	The state of the RMON agent. A ready state(1) indicates that the RMON agent instrumentation is up and ready to process SNMP requests
INT wfDCMmwNumDCM	1.3.6.1.4.1.18.3.3.2.16.1.17	INTEGER	read-only	This specifies how many DCMs are present
wfDCMTable	1.3.6.1.4.1.18.3.3.2.16.2		not-accessible	Table containing DCM records
wfDCMEntry	1.3.6.1.4.1.18.3.3.2.16.2.1		not-accessible	Information concerning a specific DCM entry. Each DCM entry corresponds to a physical probe.
INT wfDCMDelete	1.3.6.1.4.1.18.3.3.2.16.2.1.1	INTEGER	read-write	Create/Delete flag. Default is created. User can perform a set operation on this object to create/delete a DCMEntry instance.
INT wfDCMIndex	1.3.6.1.4.1.18.3.3.2.16.2.1.2	INTEGER	read-only	An index that uniquely identifies an entry in the DCM table. Each such entry defines one DCM.
INT wfDCMDisable	1.3.6.1.4.1.18.3.3.2.16.2.1.3	INTEGER	read-write	Enables or Disables the DCM
INT wfDCMOperStatus	1.3.6.1.4.1.18.3.3.2.16.2.1.4	INTEGER	read-only	This object indicates the operational state of the DCM
INT wfDCMStreamCount	1.3.6.1.4.1.18.3.3.2.16.2.1.5	INTEGER	read-only	This object indicates the number of Streams this DCM configured to support.
INT wfDCMIntfType	1.3.6.1.4.1.18.3.3.2.16.2.1.6	INTEGER	read-only	This object identifies the type of interface this DCM is configured to.
STR wfDCMImageName	1.3.6.1.4.1.18.3.3.2.16.2.1.7	DisplayString	read-write	A textual string to describe the name of the DCM image to be download on to the DCM. The image name should be a fully qualified filename. For ex: vol:filename.
INT wfDCMBootOption	1.3.6.1.4.1.18.3.3.2.16.2.1.8	INTEGER	read-write	Specifies DCM's image load mode to DCMMW. If the option specified is local, DCMMW will not load a new image to DCM's shared memory. If the option specified is download, then DCMMW will load an image into DCM's shared memory. Name of the image is specified using wfDCMMWImageName
INT wfDCMImageSaveMode	1.3.6.1.4.1.18.3.3.2.16.2.1.9	INTEGER	read-write	Specifies DCM's image save mode. If the mode is save, then DCMMW indicates it to DCM, to save the image on to its(DCM's) FLASH memory. This saved image will be used by DCM in its next boot time if the boot option is set to local. If the mode is nosave then the image will not be saved.
INT wfDCMCfgMode	1.3.6.1.4.1.18.3.3.2.16.2.1.10	INTEGER	read-write	Specifies whether DCMMW should let DCM use the config info from the shared memory or use the config info from DCM's FLASH memory. If the mode is local, then DCMMW will write `0' in DCM's config file, which indicates the DCM that it should use the config info from its FLASH memory. If the mode is shared memory, then DCMMW will write the config info in DCM's config file, for DCM to use.
INT wfDCMSaveConfigInfo	1.3.6.1.4.1.18.3.3.2.16.2.1.11	INTEGER	read-write	DCMMW uses this object to specify DCM whether it should commit the configuration information into its Flash memory or not
INT wfDCMRMONMaxHost	1.3.6.1.4.1.18.3.3.2.16.2.1.12	INTEGER	read-write	Indicates the maximum number of hosts each RMON host control entry on DCM will store. When the table reaches this value, entries will be deleted based on an LRU algorithm. The max limit depends on the amount of memory installed in DCM. It is in the range 2048..8128. DCMMW uses this object to provide the value to DCM. Check the MIB object wfDCMmwRMONHost to verify the number of hosts that got configured in the RMON host control entry.
INT wfDCMRMONDfltHost	1.3.6.1.4.1.18.3.3.2.16.2.1.13	INTEGER	read-write	DCMMW uses this to specify DCM that it should create or not create the hostControlTable. If enabled DCMMW indicates DCM to create default host entries for the interface it is configured to.
INT wfDCMRMONDfltMtrix	1.3.6.1.4.1.18.3.3.2.16.2.1.14	INTEGER	read-write	DCMMW uses this to specify DCM that it should create or not create the matrixControlTable. If enabled DCMMW indicates DCM to create default matrix entries for the interface it is configured to.
INT wfDCMRMONHost	1.3.6.1.4.1.18.3.3.2.16.2.1.15	INTEGER	read-only	This specifies the configured number of hosts in each RMON host control entry on DCM
INT wfDCMMemSize	1.3.6.1.4.1.18.3.3.2.16.2.1.16	INTEGER	read-only	This specifies DCM board's memory size
STR wfDCMHwRev	1.3.6.1.4.1.18.3.3.2.16.2.1.17	DisplayString	read-only	This specifies DCM board's HW revision number
STR wfDCMFwRev	1.3.6.1.4.1.18.3.3.2.16.2.1.18	DisplayString	read-only	This specifies DCM board's FW revision number
STR wfDCMAgentImageVersion	1.3.6.1.4.1.18.3.3.2.16.2.1.19	DisplayString	read-only	This specifies DCM board's Agent Image version number
INT wfDCMRmonObjectSupport	1.3.6.1.4.1.18.3.3.2.16.2.1.20	INTEGER	read-write	Allows a user to specify whether they want to access RMON and RMON2 stats rmon2(2), or just RMON stats rmon(1) from a specific DCM. This attribute is only used when two DCMs are present on a system. If only one DCM is present the default value will be rmon(2) and sets to this attribute will have no affect.
wfDCMStreamTable	1.3.6.1.4.1.18.3.3.2.16.3		not-accessible	Table containing DCM stream records
wfDCMStreamEntry	1.3.6.1.4.1.18.3.3.2.16.3.1		not-accessible	Information concerning a specific DCM stream entry. Each stream entry corresponds to the interface the DCM is associated with.
INT wfDCMStreamDCMIndex	1.3.6.1.4.1.18.3.3.2.16.3.1.1	INTEGER	read-only	An index that identifies the DCM entry of which this stream is associated with.
INT wfDCMStreamIndex	1.3.6.1.4.1.18.3.3.2.16.3.1.2	INTEGER	read-only	An index that uniquely identifies the particular stream this entry is associated with.
INT wfDCMStreamDisable	1.3.6.1.4.1.18.3.3.2.16.3.1.3	INTEGER	read-only	Enables or Disables DCM stream
OID wfDCMStreamDataSource	1.3.6.1.4.1.18.3.3.2.16.3.1.4	OBJECT IDENTIFIER	read-only	This object identifies the source of the data that this DCM stream entry is configured to analyze. This is the ifIndex value of the stream(interface).

RFC description

Wellfleet vendor-private MIB for DC motor control and microwave module management on Wellfleet networking equipment.

Start monitoring Legacy Wellfleet/Bay Networks routers (RMON-card hardware/firmware-revision status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-DCMMW-MIB

What Is Wellfleet-DCMMW-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description