All MIBs › WWP-LEOS-TRAFFIC-PROFILE-MIB
Organization: Ciena, Inc
Last Updated: 2011-07-07
Category: Ciena LEOS Carrier Ethernet
Description: Manages Ciena LEOS traffic profile definitions for bandwidth policing and service level enforcement.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is WWP-LEOS-TRAFFIC-PROFILE-MIB?
The WWP-LEOS-TRAFFIC-PROFILE-MIB is a vendor-specific module from World Wide Packets (later acquired by Ciena), part of the LEOS (Layer 2/3 Ethernet Operating System) family used on Ciena's carrier Ethernet switching and service demarcation platforms. It defines traffic profile objects used to configure and monitor bandwidth policing, rate limiting, and service-level enforcement applied to Ethernet services. Key data exposed includes high-capacity (HC) counters for accepted and dropped packets and bytes per traffic profile, letting operators track how much traffic conforms to or exceeds a configured profile. In terms of hardware/software status monitoring, this MIB is primarily a performance/traffic-conformance counter set rather than an environmental or CPU health MIB - it is used to verify that policing rules are correctly shaping traffic and to spot service-level violations. It has no strong dependency beyond standard SNMPv2-SMI conventions, and it is typically deployed on Ciena/WWP carrier Ethernet access and aggregation switches in metro Ethernet or Carrier Ethernet service provider networks. Engineers can download the WWP-LEOS-TRAFFIC-PROFILE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in WWP-LEOS-TRAFFIC-PROFILE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Ciena/World Wide Packets LEOS carrier Ethernet switch
- Ethernet service demarcation device
Monitoring Examples
An operator would poll wwpLeosTrafficProfileStdHCAcceptedPackets alongside the related wwpLeosTrafficProfileStdHCAcceptedBytes and wwpLeosTrafficProfileStdHCDroppedBytes counters for each configured traffic profile instance to verify SLA compliance. A rising dropped-bytes counter relative to accepted traffic would indicate that a customer or service is exceeding its committed rate and being policed, which could explain reported throughput complaints. These counters are typically indexed per profile/interface so that per-service traffic conformance can be tracked over time.
What Can Be Monitored
- accepted packets per traffic profile
- dropped packets per traffic profile
- accepted bytes (high-capacity counter)
- dropped bytes (high-capacity counter)
- traffic policing/conformance
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TruthValue |
From WWP-SMI
| wwpModules | OBJECT-IDENTITY |
| wwpModulesLeos | OBJECT-IDENTITY |
How to Use in IPNetwork Monitor
Example using wwpLeosTrafficProfileStdAcceptedBytesHi OID:
Select a Ciena/World Wide Packets LEOS carrier Ethernet switch, Ethernet service demarcation device (traffic-profile accepted/dropped byte-counter status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type wwpLeosTrafficProfileStdAcceptedBytesHi into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object specifies the higher bytes of accepted frames of given standard profile. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| wwpLeosTrafficProfileMIB | 1.3.6.1.4.1.6141.2.60.27 | Added objects wwpLeosTrafficProfileStdHCAcceptedBytes and wwpLeosTrafficProfileStdHCDroppedBytes. | ||
| wwpLeosTrafficProfileObjects | 1.3.6.1.4.1.6141.2.60.27.1 | |||
| wwpLeosTrafficProfile | 1.3.6.1.4.1.6141.2.60.27.1.1 | |||
| wwpLeosTrafficProfileGlobalAttrs | 1.3.6.1.4.1.6141.2.60.27.1.1.1 | |||
| INT wwpLeosTrafficProfileGlobalState | 1.3.6.1.4.1.6141.2.60.27.1.1.1.1 | INTEGER | read-write | Setting this object to 'enabled' will enable traffic profile globally. Setting this object to 'disabled' will disable traffic profile globally. |
| INT wwpLeosTrafficProfileGlobalMeterProvisioningState | 1.3.6.1.4.1.6141.2.60.27.1.1.1.2 | INTEGER | read-write | Setting this object to 'pir' will allow meters to be provisioned in pir. Setting this object to 'eir' will allow meters to be provisioned in eir. |
| wwpLeosTrafficProfilePortTable | 1.3.6.1.4.1.6141.2.60.27.1.1.2 | not-accessible | A table of traffic profile port entries. | |
| wwpLeosTrafficProfilePortEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1 | not-accessible | A traffic profile entry in the wwpLeosTrafficProfilePortTable. | |
| INT wwpLeosTrafficProfilePort | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.1 | INTEGER | read-only | This object specifies the port number also used as index in the table. |
| INT wwpLeosTrafficProfileAdminState | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.2 | INTEGER | read-write | Setting this object to 'enabled' will administratively enable traffic profiling on the given port. Setting this object to 'disabled' will administratively disable traffic profiling on the given port. |
| INT wwpLeosTrafficProfileOperState | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.3 | INTEGER | read-only | This object specifies operational state of the traffic profiling for a given port on the device. |
| INT wwpLeosTrafficProfileMode | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.4 | INTEGER | read-write | This object specifies the mode of traffic profiling for a given port. |
| INT wwpLeosTrafficProfileNonConformCascadedProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.5 | INTEGER | read-write | This object specifies that the device should map non-conformance traffic ingressing on a given port to cascaded profile specified by wwpLeosTrafficProfileNonConformCascadedProfile. This object will become effective only if device is running in cascaded profile mode. This object will be set to drop if using on a device that does not have cascaded-profiling |
| INT wwpLeosTrafficProfileNonConformStdProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.6 | INTEGER | read-write | This object specifies that the device should map non-conformance traffic ingressing on a given port to standard profile specified by wwpLeosTrafficProfileNonConformStdProfile. This object will become effective only if device is running in standard profile mode. |
| INT wwpLeosTrafficProfileArpCascadedProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.7 | INTEGER | read-write | This object specifies that the device should map ARP frames ingressing on a given port to cascaded profile specified by wwpLeosTrafficProfileArpCascadedProfile. This object will be set to bypass if using on a device that does not have cascaded-profiling. |
| INT wwpLeosTrafficProfileArpStdProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.8 | INTEGER | read-write | This object specifies that the device should map ARP frames ingressing on a given port to standard profile specified by wwpLeosTrafficProfileArpStdProfile. This object will become effective only if device is running in standard profile mode. |
| INT wwpLeosTrafficProfileMeterPool | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.9 | INTEGER | read-write | This object specifies the Meter Pool Index for a port. |
| INT wwpLeosTrafficProfileClassifierMode | 1.3.6.1.4.1.6141.2.60.27.1.1.2.1.10 | INTEGER | read-write | This object specifies how narrow or wide we classify traffic to a port's meters. |
| wwpLeosTrafficProfileCascadedTable | 1.3.6.1.4.1.6141.2.60.27.1.1.3 | not-accessible | A table of cascaded traffic profile entries. To create an entry in this table the following criteria must be met. - All indexes must be specified. - wwpLeosTrafficProfileCascadedCir must be specified - if wwpLeosTrafficProfileCascadedPir is not specified or is specified and is < wwpLeosTrafficProfileCascadedCir then device will make wwpLeosTrafficProfileCascadedPir = wwpLeosTrafficProfileCascadedCir - wwpLeosTrafficProfileCascadedStatus must be set to createandgo | |
| wwpLeosTrafficProfileCascadedEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.3.1 | not-accessible | A cascaded traffic profile entry in the wwpLeosTrafficProfileCascadedTable. | |
| INT wwpLeosTrafficProfileCascadedIndx | 1.3.6.1.4.1.6141.2.60.27.1.1.3.1.1 | INTEGER | read-only | This object is used as index in the table and it represents profile index which can be 1 or 2 or 3. |
| I32 wwpLeosTrafficProfileCascadedCir | 1.3.6.1.4.1.6141.2.60.27.1.1.3.1.2 | Integer32 | read-write | This object specifies the cir associated with a given cascaded traffic profile. Units are kbps. |
| I32 wwpLeosTrafficProfileCascadedPir | 1.3.6.1.4.1.6141.2.60.27.1.1.3.1.3 | Integer32 | read-write | This object specifies the pir associated with a given cascaded traffic profile. Units are kbps. |
| ROW wwpLeosTrafficProfileCascadedStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.3.1.5 | RowStatus | read-create | Setting this object to 'createandgo' along with wwpLeosTrafficProfileCascadedCir and wwpLeosTrafficProfileCascadedPir will result in creating an cascaded traffic profile entry. Setting this object to 'destroy' will delete the entry from the table. |
| wwpLeosTrafficProfileStdTable | 1.3.6.1.4.1.6141.2.60.27.1.1.4 | not-accessible | A table of Std traffic profile entries. To create entry in this table following criteria must be met. - All indexes must be specified. - wwpLeosTrafficProfileStdCir must be specified - if wwpLeosTrafficProfileStdPir is not specified or is specified and is < wwpLeosTrafficProfileStdCir then device will make wwpLeosTrafficProfileStdPir = wwpLeosTrafficProfileStdCir - wwpLeosTrafficProfileStdStatus must be set to createandgo | |
| wwpLeosTrafficProfileStdEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1 | not-accessible | A standard traffic profile entry in the wwpLeosTrafficProfileStdTable. | |
| INT wwpLeosTrafficProfileStdIndx | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.1 | INTEGER | read-only | This object is used as index in the table and it represents profile index which can be 1 through 64. |
| I32 wwpLeosTrafficProfileStdCir | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.2 | Integer32 | read-write | This object specifies the cir associated with a given standard traffic profile. |
| I32 wwpLeosTrafficProfileStdPir | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.3 | Integer32 | read-write | This object specifies the pir associated with a given standard traffic profile. |
| STR wwpLeosTrafficProfileStdName | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.4 | DisplayString | read-create | The name associated with this profile. This must be unique per port. The name does not have to be set on create. However, when updating the name, it must have some value - zero-string not support. |
| ROW wwpLeosTrafficProfileStdStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.5 | RowStatus | read-create | Setting this object to 'createandgo' along with wwpLeosTrafficProfileStdCir and or wwpLeosTrafficProfileStdPir will result in creating an standard traffic profile entry. Setting this object to 'destroy' will delete the entry from the table. |
| INT wwpLeosTrafficProfileStdVlan | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.6 | INTEGER | read-write | This object specifies the VLAN associated with a profile. |
| U32 wwpLeosTrafficProfileStdCbs | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.7 | Unsigned32 | read-write | This object specifies the Commited burst size associated with a given standard traffic profile. |
| U32 wwpLeosTrafficProfileStdEbs | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.8 | Unsigned32 | read-write | This object specifies the Excess burst size associated with a given standard traffic profile. |
| INT wwpLeosTrafficProfileStdDscpRemarkPolicy | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.9 | INTEGER | read-write | Leave => Don't remark the frame. Fixed => Remark the DSCP of a frame with the fixed-dscp value for IP frames which classify to the Traffic Profile |
| INT wwpLeosTrafficProfileStdFixedDscp | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.10 | INTEGER | read-write | Fixed DSCP value to use for frames classifying to a Traffic Profile when the dscp-remark-policy id 'Fixed |
| INT wwpLeosTrafficProfileStdUnsetVlan | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.11 | INTEGER | read-write | Setting This object to unset(1) unsets the VLAN associated with a profile. This object returns a value of none(0) on get. |
| INT wwpLeosTrafficProfileStdDefaultProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.12 | INTEGER | read-create | Setting this object to true(1) during createAndGo(4) will create Tier-1 default profile. |
| INT wwpLeosTrafficeProfileStdDrop | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.13 | INTEGER | read-create | Setting this value to true causes metering to cease and all traffic to drop. |
| I32 wwpLeosTrafficProfileStdParentIndex | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.14 | Integer32 | read-create | This mib object is set when creating Child traffic profile to specify the parent index |
| INT wwpLeosTrafficProfileStdChildMode | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.15 | INTEGER | read-create | When the port mode is hierarchical-vlan, then the valid child-modes are dot1dPri, ipprec, dscp. When the port mode is hierarchical-port then the valid childModes is dot1dPri, ipprec, dscp and vlan(4). |
| INT wwpLeosTrafficProfileStdStatsMonitor | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.16 | INTEGER | read-write | To disable stats collection, set this object to off(2). To enable stats collection, set this object to on(1). |
| INT wwpLeosTrafficProfileStdUntaggedState | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.17 | INTEGER | read-write | To enable this profile to match untagged traffic set this to on(1). To disable, set to off(2) |
| STR wwpLeosTrafficProfileStdVs | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.18 | DisplayString | read-create | The virtual-switch name associated with this profile. The virtual-switch name must exist before using it as a profile classifier. |
| INT wwpLeosTrafficProfileStdRemarkColorPolicy | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.19 | INTEGER | read-write | This sets the profile's color remarking policy at the meter output. |
| INT wwpLeosTrafficProfileStdRemarkRcosPolicy | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.20 | INTEGER | read-write | This sets the profile's rcos remarking policy based on meter color. |
| INT wwpLeosTrafficProfileStdYellowRemarkRcos | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.21 | INTEGER | read-write | This sets the profile's rcos remarking policy based on meter color. |
| INT wwpLeosTrafficProfileStdGreenRemarkRcos | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.22 | INTEGER | read-write | This sets the profile's rcos remarking policy based on meter color. |
| INT wwpLeosTrafficProfileStdIngressColorAware | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.23 | INTEGER | read-write | This sets the profile's meter ingress color awareness. |
| I32 wwpLeosTrafficProfileStdEir | 1.3.6.1.4.1.6141.2.60.27.1.1.4.1.24 | Integer32 | read-write | This object specifies the eir associated with a given standard traffic profile. Sets/Gets on this are only valid when the global meter-provisioning mode is set to eir. All other times it will be ignored and return 0 |
| wwpLeosTrafficProfileStdDot1dTable | 1.3.6.1.4.1.6141.2.60.27.1.1.5 | not-accessible | A table of Std dot1d traffic profile entries. To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdDot1dStatus to 'createandgo'. - set wwpLeosTrafficProfileStdDot1dToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdDot1dStatus to destroy. | |
| wwpLeosTrafficProfileStdDot1dEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.5.1 | not-accessible | A standard dot1d traffic profile entry in the wwpLeosTrafficProfileStdDot1dTable. | |
| INT wwpLeosTrafficProfileStdDot1d | 1.3.6.1.4.1.6141.2.60.27.1.1.5.1.1 | INTEGER | read-only | This object specifies the dot1d priority for the associated standard profile entry in the wwpLeosTrafficProfileStdDot1dTable table. |
| INT wwpLeosTrafficProfileStdDot1dToProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.5.1.2 | INTEGER | read-write | This object specifies the profile to which wwpLeosTrafficProfileStdDot1d must be mapped to. |
| ROW wwpLeosTrafficProfileStdDot1dStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.5.1.3 | RowStatus | read-create | To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdDot1dStatus to 'createandgo'. - set wwpLeosTrafficProfileStdDot1dToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdDot1dStatus to destroy. |
| wwpLeosTrafficProfileStdIpPrecTable | 1.3.6.1.4.1.6141.2.60.27.1.1.6 | not-accessible | A table of standard ip precedence traffic profile entries. To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdIpPrecStatus to 'createandgo'. - set wwpLeosTrafficProfileStdIpPrecToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdIpPrecStatus to destroy. | |
| wwpLeosTrafficProfileStdIpPrecEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.6.1 | not-accessible | A standard ip precedence traffic profile entry in the wwpLeosTrafficProfileStdTable. | |
| INT wwpLeosTrafficProfileStdIpPrec | 1.3.6.1.4.1.6141.2.60.27.1.1.6.1.1 | INTEGER | read-only | This object specifies the ip precedence for the associated standard profile entry in wwpLeosTrafficProfileStdTable. |
| INT wwpLeosTrafficProfileStdIpPrecToProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.6.1.2 | INTEGER | read-write | This object specifies the profile to which wwpLeosTrafficProfileStdIpPrec must be mapped to. |
| ROW wwpLeosTrafficProfileStdIpPrecStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.6.1.3 | RowStatus | read-create | To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdIpPrecStatus to 'createandgo'. - set wwpLeosTrafficProfileStdIpPrecToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdIpPrecStatus to destroy. |
| wwpLeosTrafficProfileStdPhbTable | 1.3.6.1.4.1.6141.2.60.27.1.1.7 | not-accessible | A table of standard phb traffic profile entries. To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdPhbStatus to 'createandgo'. - set wwpLeosTrafficProfileStdPhbToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdPhbStatus to destroy. | |
| wwpLeosTrafficProfileStdPhbEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.7.1 | not-accessible | A standard Phb traffic profile entry in the wwpLeosTrafficProfileStdTable. | |
| INT wwpLeosTrafficProfileStdPhb | 1.3.6.1.4.1.6141.2.60.27.1.1.7.1.1 | INTEGER | read-only | This object specifies the diff-serv values for the associated standard profile entry in wwpLeosTrafficProfileStdTable. |
| INT wwpLeosTrafficProfileStdPhbToProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.7.1.2 | INTEGER | read-write | This object specifies the profile to which wwpLeosTrafficProfileStdPhb must be mapped to. |
| ROW wwpLeosTrafficProfileStdPhbStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.7.1.3 | RowStatus | read-create | To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdPhbStatus to 'createandgo'. - set wwpLeosTrafficProfileStdPhbToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdPhbStatus to destroy. |
| wwpLeosTrafficProfileCascadedStatsTable | 1.3.6.1.4.1.6141.2.60.27.1.1.8 | not-accessible | A table of cascaded profile stats. | |
| wwpLeosTrafficProfileCascadedStatsEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.8.1 | not-accessible | A cascaded traffic profile entry in the wwpLeosTrafficProfileCascadedStatsTable. | |
| C32 wwpLeosTrafficProfileCascadedAcceptedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.8.1.1 | Counter32 | read-only | This object specifies the higher bytes of accepted frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedAcceptedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.8.1.2 | Counter32 | read-only | This object specifies the lower bytes of accepted frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedDroppedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.8.1.3 | Counter32 | read-only | This object specifies the higher bytes of dropped frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedDroppedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.8.1.4 | Counter32 | read-only | This object specifies the lower bytes of dropped frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedRemarkedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.8.1.5 | Counter32 | read-only | This object specifies the higher bytes of remarked frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedRemarkedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.8.1.6 | Counter32 | read-only | This object specifies the lower bytes of remarked frames of given cascaded profile. |
| wwpLeosTrafficProfileStdStatsTable | 1.3.6.1.4.1.6141.2.60.27.1.1.9 | not-accessible | A table of standard profile stats. | |
| wwpLeosTrafficProfileStdStatsEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1 | not-accessible | The entry in wwpLeosTrafficProfileStdStatsTable. | |
| C32 wwpLeosTrafficProfileStdAcceptedBytesHiEx | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1.1 | Counter32 | read-only | This object specifies the higher bytes of accepted frames of given standard profile. |
| C32 wwpLeosTrafficProfileStdAcceptedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1.2 | Counter32 | read-only | This object specifies the lower bytes of accepted frames of given standard profile. |
| C32 wwpLeosTrafficProfileStdDroppedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1.3 | Counter32 | read-only | This object specifies the higher bytes of dropped frames of given standard profile. |
| C32 wwpLeosTrafficProfileStdDroppedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1.4 | Counter32 | read-only | This object specifies the higher bytes of dropped frames of given standard profile. |
| C64 wwpLeosTrafficProfileStdHCAcceptedBytes | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1.5 | Counter64 | read-only | This object specifies the bytes of accepted frame data by a given standard profile. |
| C64 wwpLeosTrafficProfileStdHCDroppedBytes | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1.6 | Counter64 | read-only | This object specifies the bytes of dropped frame data by a given standard profile. |
| C64 wwpLeosTrafficProfileStdHCAcceptedPackets | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1.7 | Counter64 | read-only | This object specifies the number of packets passed by a standard profile |
| C64 wwpLeosTrafficProfileStdHCDroppedPackets | 1.3.6.1.4.1.6141.2.60.27.1.1.9.1.8 | Counter64 | read-only | This object specifies the number of packets dropped by a standard profile |
| wwpLeosTrafficProfileCascadedGlobalTable | 1.3.6.1.4.1.6141.2.60.27.1.1.10 | not-accessible | A table of global attributes used by cascaded traffic profile table. To create entry in this table following criteria must be met. - All indexes must be specified. - wwpLeosTrafficProfileCascadedGlobalDot1d,wwpLeosTrafficProfileCascadedGlobalIpPrec and wwpLeosTrafficProfileCascadedGlobalDscp may be specified. - wwpLeosTrafficProfileCascadedGlobalName may be specified. - wwpLeosTrafficProfileCascadedGlobalStatus must be set to createandgo | |
| wwpLeosTrafficProfileCascadedGlobalEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.10.1 | not-accessible | A global cascaded traffic profile entry in the wwpLeosTrafficProfileCascadedGlobalTable. | |
| INT wwpLeosTrafficProfileCascadedGlobalDot1d | 1.3.6.1.4.1.6141.2.60.27.1.1.10.1.1 | INTEGER | read-write | This specifies the dot1d priority for a given cascaded traffic profile. If this object returns -1 then it means the value was not set by user and thus doesn't care. |
| INT wwpLeosTrafficProfileCascadedGlobalIpPrec | 1.3.6.1.4.1.6141.2.60.27.1.1.10.1.2 | INTEGER | read-write | This specifies the ip precedence value for a given cascaded traffic profile. If this object returns -1 then it means the value was not set by user and thus doesn't care. |
| INT wwpLeosTrafficProfileCascadedGlobalDscp | 1.3.6.1.4.1.6141.2.60.27.1.1.10.1.3 | INTEGER | read-write | This specifies the dscp value for a given cascaded traffic profile. If this object returns -1 then it means the value was not set by user and thus doesn't care. |
| STR wwpLeosTrafficProfileCascadedGlobalName | 1.3.6.1.4.1.6141.2.60.27.1.1.10.1.4 | DisplayString | read-write | The name associated with this profile. This must be unique name per profile. The name does not have to be set on create. However, when updating the name, it must have some value - zero-string not support. |
| ROW wwpLeosTrafficProfileCascadedGlobalStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.10.1.5 | RowStatus | read-create | Setting this object to 'createandgo' will result in creating an global cascaded traffic profile entry. Setting this object to 'destroy' will delete the entry from the table. |
| wwpLeosTrafficProfileCascadedTotalStatsTable | 1.3.6.1.4.1.6141.2.60.27.1.1.11 | not-accessible | A table of cascaded profile stats. | |
| wwpLeosTrafficProfileCascadedTotalStatsEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.11.1 | not-accessible | A cascaded traffic profile entry in the wwpLeosTrafficProfileCascadedTotalStatsTable. | |
| C32 wwpLeosTrafficProfileCascadedTotalAcceptedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.11.1.1 | Counter32 | read-only | This object specifies the higher bytes of accepted frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedTotalAcceptedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.11.1.2 | Counter32 | read-only | This object specifies the lower bytes of accepted frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedTotalDroppedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.11.1.3 | Counter32 | read-only | This object specifies the higher bytes of dropped frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedTotalDroppedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.11.1.4 | Counter32 | read-only | This object specifies the lower bytes of dropped frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedTotalRemarkedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.11.1.5 | Counter32 | read-only | This object specifies the higher bytes of remarked frames of given cascaded profile. |
| C32 wwpLeosTrafficProfileCascadedTotalRemarkedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.11.1.6 | Counter32 | read-only | This object specifies the lower bytes of remarked frames of given cascaded profile. |
| wwpLeosTrafficProfileStdTotalStatsTable | 1.3.6.1.4.1.6141.2.60.27.1.1.12 | not-accessible | A table of standard profile stats. | |
| wwpLeosTrafficProfileStdTotalStatsEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.12.1 | not-accessible | The entry in wwpLeosTrafficProfileStdTotalStatsTable. | |
| C32 wwpLeosTrafficProfileStdTotalAcceptedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.12.1.1 | Counter32 | read-only | This object specifies the higher bytes of accepted frames of given standard profile. |
| C32 wwpLeosTrafficProfileStdTotalAcceptedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.12.1.2 | Counter32 | read-only | This object specifies the lower bytes of accepted frames of given standard profile. |
| C32 wwpLeosTrafficProfileStdTotalDroppedBytesHi | 1.3.6.1.4.1.6141.2.60.27.1.1.12.1.3 | Counter32 | read-only | This object specifies the higher bytes of dropped frames of given standard profile. |
| C32 wwpLeosTrafficProfileStdTotalDroppedBytesLo | 1.3.6.1.4.1.6141.2.60.27.1.1.12.1.4 | Counter32 | read-only | This object specifies the higher bytes of dropped frames of given standard profile. |
| wwpLeosTrafficProfileStdVlanTable | 1.3.6.1.4.1.6141.2.60.27.1.1.14 | not-accessible | A table of Std Vlan Traffic Profile Entries. To create entry in the table following criteria must be met -- set wwpLeosTrafficProfileStdVlanStatus to 'createandgo'. -- set wwpLeosTrafficProfileStdVlan to valid profile. To delete entry set wwpLeosTrafficProfileStdVlanStatus to destroy. | |
| wwpLeosTrafficProfileStdVlanEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.14.1 | not-accessible | A standard Dscp traffic profile entry in the wwpLeosTrafficProfileStdTable. | |
| INT wwpLeosTrafficProfileStdVlanIndex | 1.3.6.1.4.1.6141.2.60.27.1.1.14.1.1 | INTEGER | not-accessible | This object specifies the Vlan for the associated standard profile entry in wwpLeosTrafficProfileStdTable. |
| INT wwpLeosTrafficProfileStdVlanToProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.14.1.2 | INTEGER | read-create | This object specifies the profile to which wwpLeosTrafficProfileStdVlan must be mapped to. |
| ROW wwpLeosTrafficProfileStdVlanStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.14.1.3 | RowStatus | read-create | To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdVlanStatus to 'createandgo'. - set wwpLeosTrafficProfileStdVlanToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdVlanStatus to destroy. |
| wwpLeosTrafficProfileStdDscpTable | 1.3.6.1.4.1.6141.2.60.27.1.1.15 | not-accessible | A table of standard Dscp traffic profile entries. To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdDscpStatus to 'createandgo'. - set wwpLeosTrafficProfileStdDscpToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdDscpStatus to destroy. | |
| wwpLeosTrafficProfileStdDscpEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.15.1 | not-accessible | A standard Dscp traffic profile entry in the wwpLeosTrafficProfileStdTable. | |
| INT wwpLeosTrafficProfileStdDscp | 1.3.6.1.4.1.6141.2.60.27.1.1.15.1.1 | INTEGER | not-accessible | This object specifies the Dscp for the associated standard profile entry in wwpLeosTrafficProfileStdTable. |
| INT wwpLeosTrafficProfileStdDscpToProfile | 1.3.6.1.4.1.6141.2.60.27.1.1.15.1.2 | INTEGER | read-create | This object specifies the profile to which wwpLeosTrafficProfileStdDscp must be mapped to. |
| ROW wwpLeosTrafficProfileStdDscpStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.15.1.3 | RowStatus | read-create | To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdDscpStatus to 'createandgo'. - set wwpLeosTrafficProfileStdDscpToProfile to valid profile. To delete entry set wwpLeosTrafficProfileStdDscpStatus to destroy. |
| wwpLeosTrafficProfileMeterPoolTable | 1.3.6.1.4.1.6141.2.60.27.1.1.16 | not-accessible | A Table of Meter Pool | |
| wwpLeosTrafficProfileMeterPoolEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1 | not-accessible | A Meter Pool Entry in wwpLeosTrafficProfileMeterPoolTable | |
| INT wwpLeosTrafficProfileMeterPoolIndex | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1.1 | INTEGER | not-accessible | A Meter Pool Index |
| STR wwpLeosTrafficProfileMeterPoolName | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1.2 | DisplayString | read-only | A Meter Pool Name |
| I32 wwpLeosTrafficProfileMeterPoolNumOfMeters | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1.3 | Integer32 | read-only | Number of Meters for a pool |
| I32 wwpLeosTrafficProfileMeterPoolMetersUsed | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1.4 | Integer32 | read-only | Number of Used Meters in a Pool |
| I32 wwpLeosTrafficProfileMeterPoolNumOfStats | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1.5 | Integer32 | read-only | Number of Stats Counters for a pool |
| I32 wwpLeosTrafficProfileMeterPoolStatsUsed | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1.6 | Integer32 | read-only | Number of Used Stats Counters in a Pool |
| I32 wwpLeosTrafficProfileMeterPoolNumOfClassifiers | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1.7 | Integer32 | read-only | Number of Classifiers for a pool |
| I32 wwpLeosTrafficProfileMeterPoolClassifiersUsed | 1.3.6.1.4.1.6141.2.60.27.1.1.16.1.8 | Integer32 | read-only | Number of Used Classifiers in a Pool |
| wwpLeosTrafficProfileTosStampTable | 1.3.6.1.4.1.6141.2.60.27.1.1.20 | not-accessible | A table of TosStamps entries. | |
| wwpLeosTrafficProfileTosStampEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.20.1 | not-accessible | The entry in wwpLeosTrafficProfileTosStampTable. | |
| INT wwpLeosTrafficProfileTosStampState | 1.3.6.1.4.1.6141.2.60.27.1.1.20.1.1 | INTEGER | read-write | This object specifies the state of the TOS Stamp on a port |
| INT wwpLeosTrafficProfileTosStampValue | 1.3.6.1.4.1.6141.2.60.27.1.1.20.1.2 | INTEGER | read-write | This object specifies the Value of the TOS Stamp. For IP prec left shift the value by 3 bits. |
| wwpLeosTrafficProfileIpDscpTable | 1.3.6.1.4.1.6141.2.60.27.1.1.21 | not-accessible | A table of IpDscp entries. | |
| wwpLeosTrafficProfileIpDscpEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1 | not-accessible | The entry in wwpLeosTrafficProfileIpDscpTable. | |
| INT wwpLeosTrafficProfileIpp0Cs0State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.1 | INTEGER | read-write | This object specifies the state of the Ipp0 or cs0 enable disable on a port |
| INT wwpLeosTrafficProfileIpp1Cs1State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.2 | INTEGER | read-write | This object specifies the state of the Ipp1 or cs1 enable disable on a port |
| INT wwpLeosTrafficProfileIpp2Cs2State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.3 | INTEGER | read-write | This object specifies the state of the Ipp0 or cs0 enable disable on a port |
| INT wwpLeosTrafficProfileIpp3Cs3State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.4 | INTEGER | read-write | This object specifies the state of the Ipp3 or cs3 enable disable on a port |
| INT wwpLeosTrafficProfileIpp4Cs4State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.5 | INTEGER | read-write | This object specifies the state of the Ipp4 or cs4 enable disable on a port |
| INT wwpLeosTrafficProfileIpp5Cs5State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.6 | INTEGER | read-write | This object specifies the state of the Ipp5 or cs5 enable disable on a port |
| INT wwpLeosTrafficProfileIpp6Cs6State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.7 | INTEGER | read-write | This object specifies the state of the Ipp6 or cs6 enable disable on a port |
| INT wwpLeosTrafficProfileIpp7Cs7State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.8 | INTEGER | read-write | This object specifies the state of the Ipp7 or cs7 enable disable on a port |
| INT wwpLeosTrafficProfileAf1State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.9 | INTEGER | read-write | This object specifies the state of the Af1 enable disable on a port |
| INT wwpLeosTrafficProfileAf2State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.10 | INTEGER | read-write | This object specifies the state of the Af2 enable disable on a port |
| INT wwpLeosTrafficProfileAf3State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.11 | INTEGER | read-write | This object specifies the state of the Af3 enable disable on a port |
| INT wwpLeosTrafficProfileAf4State | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.12 | INTEGER | read-write | This object specifies the state of the Af4 enable disable on a port |
| INT wwpLeosTrafficProfileEfState | 1.3.6.1.4.1.6141.2.60.27.1.1.21.1.13 | INTEGER | read-write | This object specifies the state of the Ef enable disable on a port |
| wwpLeosTrafficProfileStdVlanDot1dTable | 1.3.6.1.4.1.6141.2.60.27.1.1.40 | not-accessible | A table of Std Vlan dot1d traffic profile entries. To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdDot1dStatus to 'createandgo'. To delete entry set wwpLeosTrafficProfileStdDot1dStatus to destroy. | |
| wwpLeosTrafficProfileStdVlanDot1dEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.40.1 | not-accessible | A standard dot1d traffic profile entry in the wwpLeosTrafficProfileStdDot1dTable. | |
| ROW wwpLeosTrafficProfileStdVlanDot1dStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.40.1.1 | RowStatus | read-create | To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdDot1dStatus to 'createandgo'. To delete entry set wwpLeosTrafficProfileStdDot1dStatus to destroy. |
| wwpLeosTrafficProfileStdVlanIpPrecTable | 1.3.6.1.4.1.6141.2.60.27.1.1.41 | not-accessible | A table of Std Vlan-Ip prec traffic profile entries. To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdVlanIpPrecStatus to 'createandgo'. To delete entry set wwpLeosTrafficProfileStdVlanIpPrecStatus to destroy. | |
| wwpLeosTrafficProfileStdVlanIpPrecEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.41.1 | not-accessible | A standard vlan-Ip prec traffic profile entry in the wwpLeosTrafficProfileStdVlanIpPrecTable. | |
| ROW wwpLeosTrafficProfileStdVlanIpPrecStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.41.1.1 | RowStatus | read-create | To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdVlanIpPrecStatus to 'createandgo'. To delete entry set wwpLeosTrafficProfileStdVlanIpPrecStatus to destroy. |
| wwpLeosTrafficProfileStdVlanDscpTable | 1.3.6.1.4.1.6141.2.60.27.1.1.42 | not-accessible | A table of Std Vlan-dscp traffic profile entries. To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdVlanDscpStatus to 'createandgo'. To delete entry set wwpLeosTrafficProfileStdVlanDscpStatus to destroy. | |
| wwpLeosTrafficProfileStdVlanDscpEntry | 1.3.6.1.4.1.6141.2.60.27.1.1.42.1 | not-accessible | A standard vlan-dscp traffic profile entry in the wwpLeosTrafficProfileStdVlanDscpTable. | |
| ROW wwpLeosTrafficProfileStdVlanDscpStatus | 1.3.6.1.4.1.6141.2.60.27.1.1.42.1.2 | RowStatus | read-create | To create entry in the table following criteria must be met - set wwpLeosTrafficProfileStdVlanDscpStatus to 'createandgo'. To delete entry set wwpLeosTrafficProfileStdVlanDscpStatus to destroy. |
| wwpLeosTrafficProfileNotificationPrefix | 1.3.6.1.4.1.6141.2.60.27.2 | |||
| wwpLeosTrafficProfileNotifications | 1.3.6.1.4.1.6141.2.60.27.2.0 | |||
| wwpLeosTrafficProfileMIBConformance | 1.3.6.1.4.1.6141.2.60.27.3 | |||
| wwpLeosTrafficProfileMIBCompliances | 1.3.6.1.4.1.6141.2.60.27.3.1 | |||
| wwpLeosTrafficProfileMIBGroups | 1.3.6.1.4.1.6141.2.60.27.3.2 |
RFC description
Manages traffic profiling and classification on Ciena LEOS switches, supporting QoS policies and traffic shaping.
Start monitoring Ciena/World Wide Packets LEOS carrier Ethernet switch, Ethernet service demarcation device (traffic-profile accepted/dropped byte-counter status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.