WIPIPE-MIB

All MIBs › WIPIPE-MIB

Category: Generic Wireless and Broadband

Description: Manages WiPipe cellular router interface bonding, tunnel status, and WAN link failover configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is WIPIPE-MIB?

WIPIPE-MIB is the vendor MIB for WiPipe cellular routers, gateway devices that provide WAN connectivity, interface bonding, and failover over cellular modem links. It exposes objects covering firmware upgrade management, GPIO input/output configuration and readback (used for external alarm or control wiring), and a modem table enumerating attached cellular modems. Its monitoring role centers on device software and hardware status: it reports firmware version and in-progress upgrade status (with URL and status codes), and it lets an operator poll GPIO pins for hardware alarm/contact-closure states as well as enumerate modem instances to check WAN link health across bonded connections. No module description was provided so dependency details are unclear, but it likely relies on standard MIB-II interface objects for the underlying WAN link statistics. It is typically deployed on ruggedized cellular routers used for M2M/IoT WAN failover in retail, industrial, or vehicle telematics settings, and a WIPIPE-MIB download lets administrators load the module into their SNMP management software.

IPNetwork Monitor allows you to monitor SNMP objects defined in WIPIPE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

WiPipe cellular router
M2M/IoT cellular gateway

Monitoring Examples

An operator would poll devFWVersion and devFWUpgradeStatus to confirm whether a remote firmware push to a fleet of routers succeeded, using devFWUpgradeURL to verify the correct image source was used. mdmTable/mdmEntry indexed by mdmIndex lets an admin enumerate each cellular modem installed in the router and check its individual link/bonding status against mdmNumber. devGpioReadInput and devGpioReadOutput can be polled to detect an external alarm condition, such as a door contact or power-loss signal wired into the router's GPIO header.

What Can Be Monitored

firmware version
firmware upgrade status
GPIO input/output state
modem table entries
WAN bonding/tunnel status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

enterprises

OIDs

OID symbolic	OID numeric	Type	Access	Description
wipipe	1.3.6.1.4.1.20992
wipipeMgmt	1.3.6.1.4.1.20992.1
wipipeDevice	1.3.6.1.4.1.20992.1.1
STR devFWVersion	1.3.6.1.4.1.20992.1.1.1	DisplayString	read-only	A textual description providing the firmware version currently running on the device. It is mandatory that this only contain printable ASCII characters. @GET-FUNC=snmp_get_devFWVersion
INT devFWUpgrade	1.3.6.1.4.1.20992.1.1.2	INTEGER	read-write	Initiate a FW upgrade on the device. none - No upgrade is being performed or initiated. auto - If no other upgrade is begin performed, when this value is written then an automatic upgrade will be performed. When an automatic upgrade is done then the device will pull the most current FW image from the Wipipe server and install it. If this value is read then the router is performing an automatic upgrade and the devFWUpgradeStatus object should be read for further information. manual - If no other upgrade is begin performed, when this value is written then a manual upgrade will be performed. When an manual upgrade is done it will use the URL set in the devFWUpgradeURL object as the place to get the firmware image and install. If the devFWUpgradeURL object is not set then no upgrade will be performed. If this value is read then the router is performing an manual upgrade and the devFWUpgradeStatus object should be read for further information. - @SET-FUNC=snmp_set_devFWUpgrade @GET-FUNC=snmp_get_devFWUpgrade
STR devFWUpgradeURL	1.3.6.1.4.1.20992.1.1.3	DisplayString	read-write	Set the URL that points to the firmware image that will be used when doing a manual firmware upgrade. @SET-FUNC=snmp_set_devFWUpgradeURL @GET-FUNC=snmp_get_devFWUpgradeURL
INT devFWUpgradeStatus	1.3.6.1.4.1.20992.1.1.4	INTEGER	read-only	Show the result of the FW upgrade command. idle = there is no upgrade in process. upgrading = the new FW is being downloaded and written to flash. uptodate = the device is already at the latest FW. Nothing to upgrade. updateAvail - the device has an automatic update available. failure = some sort of failure occurred during the upgrade. The FW will not be upgraded. NOTE - while the FW image is being written to flash interrupts are disabled so no status will be returned at this time. User should get the FW version string in order to determine if the unit has been updated successfully. @GET-FUNC=snmp_get_devFWUpgradeStatus
INT devGpioConfigInput	1.3.6.1.4.1.20992.1.1.5	INTEGER	read-write	Set the Input GPIO config on the connector. none - ignore input value. input - read the input value. reboot - if the input is held low for 10 seconds, reboot the router. ignition_sensing - if the input is held low for 300 seconds, power off the router. IBR11x0 series feature. @SET-FUNC=snmp_set_devGpioConfigInput @GET-FUNC=snmp_get_devGpioConfigInput
INT devGpioReadInput	1.3.6.1.4.1.20992.1.1.6	INTEGER	read-only	Read the Input GPIO value on the connector. 0 - low. 1 - high. @SET-FUNC=snmp_set_devGpioReadInput @GET-FUNC=snmp_get_devGpioReadInput
INT devGpioConfigOutput	1.3.6.1.4.1.20992.1.1.7	INTEGER	read-write	Set the output GPIO config on the connector. low - Default low output value. high - high output value. routerRunning - high output value once the router completes its boot process. modemConnected - high output value when the modem completes a data connection @SET-FUNC=snmp_set_devGpioConfigOutput @GET-FUNC=snmp_get_devGpioConfigOutput
INT devGpioReadOutput	1.3.6.1.4.1.20992.1.1.8	INTEGER	read-only	Read the Output GPIO value on the connector. 0 - low. 1 - high. @SET-FUNC=snmp_set_devGpioReadOutput @GET-FUNC=snmp_get_devGpioReadOutput
wipipeCellMdm	1.3.6.1.4.1.20992.1.2
INT mdmNumber	1.3.6.1.4.1.20992.1.2.1	INTEGER	read-only	The number of Cellular Modems (regardless of their current state) present on this system. @GET-FUNC=snmp_get_mdmNumber
mdmTable	1.3.6.1.4.1.20992.1.2.2		not-accessible	A list of Modem entries. The number of entries is given by the value of ifNumber.
mdmEntry	1.3.6.1.4.1.20992.1.2.2.1		not-accessible	An entry containing management information applicable to a particular modem. @ROW-FUNC=snmp_get_mdmTable_row
INT mdmIndex	1.3.6.1.4.1.20992.1.2.2.1.1	INTEGER	read-only	A unique value, greater than zero, for each cellular modem. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
STR mdmDescr	1.3.6.1.4.1.20992.1.2.2.1.2	DisplayString	read-only	A textual string containing information about the modem.
STR mdmPort	1.3.6.1.4.1.20992.1.2.2.1.3	DisplayString	read-only	A textual string containing information about what port the modem is installed in.
INT mdmSignalStrength	1.3.6.1.4.1.20992.1.2.2.1.4	INTEGER	read-only	The cellular modems signal strength, given in dBm's.
INT mdmStatus	1.3.6.1.4.1.20992.1.2.2.1.5	INTEGER	read-only	A textual string containing infomation of the state of the modem.
INT mdmECIO	1.3.6.1.4.1.20992.1.2.2.1.6	INTEGER	read-only	The cellular modems Ec/Io ratio given in dBm's.
STR mdmSerialNumber	1.3.6.1.4.1.20992.1.2.2.1.7	DisplayString	read-only	A textual string representing the unique serial number of the device.
STR mdmFirmwareVersion	1.3.6.1.4.1.20992.1.2.2.1.8	DisplayString	read-only	A textual string representing the current firmware version of the modem. Not all modems report this value.
STR mdmMDN	1.3.6.1.4.1.20992.1.2.2.1.9	DisplayString	read-only	A textual string representing the unique Mobile Directory Number of the device.
STR mdmSERDIS	1.3.6.1.4.1.20992.1.2.2.1.10	DisplayString	read-only	A textual string representing the Service Display of the device.
STR mdmPROF	1.3.6.1.4.1.20992.1.2.2.1.11	DisplayString	read-only	A textual string representing the Profile of the device.
INT mdmCINR	1.3.6.1.4.1.20992.1.2.2.1.12	INTEGER	read-only	The cellular modems CINR ratio given in dBm's.
INT mdmSINR	1.3.6.1.4.1.20992.1.2.2.1.13	INTEGER	read-only	The cellular modems SINR ratio given in dBm's.
INT mdmRSRP	1.3.6.1.4.1.20992.1.2.2.1.14	INTEGER	read-only	The cellular modems RSRP given in dBm's.
INT mdmRSRQ	1.3.6.1.4.1.20992.1.2.2.1.15	INTEGER	read-only	The cellular modems RSRQ given in dBm's.
INT mdmROAM	1.3.6.1.4.1.20992.1.2.2.1.16	INTEGER	read-only	The cellular modems Roaming Status.
STR mdmRFBAND	1.3.6.1.4.1.20992.1.2.2.1.17	DisplayString	read-only	The cellular modems RF band.
STR mdmHOMECARRIER	1.3.6.1.4.1.20992.1.2.2.1.18	DisplayString	read-only	The cellular modems Home Carrier.
STR mdmIMSI	1.3.6.1.4.1.20992.1.2.2.1.19	DisplayString	read-only	The cellular modems IMSI.
STR mdmIMEI	1.3.6.1.4.1.20992.1.2.2.1.20	DisplayString	read-only	The cellular modems IMEI.
STR mdmAPN	1.3.6.1.4.1.20992.1.2.2.1.21	DisplayString	read-only	The cellular modems APN.
STR mdmRFCHANNEL	1.3.6.1.4.1.20992.1.2.2.1.22	DisplayString	read-only	The cellular modems RF Channel.
wipipeProd	1.3.6.1.4.1.20992.2
mbr1000	1.3.6.1.4.1.20992.2.1
ctr500	1.3.6.1.4.1.20992.2.2
mbr800	1.3.6.1.4.1.20992.2.3
mbr1100	1.3.6.1.4.1.20992.2.4
mbr1200	1.3.6.1.4.1.20992.2.5
mbr900	1.3.6.1.4.1.20992.2.6
cba250	1.3.6.1.4.1.20992.2.7
cba750	1.3.6.1.4.1.20992.2.8
cx111	1.3.6.1.4.1.20992.2.9
mbr1400	1.3.6.1.4.1.20992.2.10
mbr1200b	1.3.6.1.4.1.20992.2.11
cbr400	1.3.6.1.4.1.20992.2.12
cbr450	1.3.6.1.4.1.20992.2.13
ibr600	1.3.6.1.4.1.20992.2.14
ibr650	1.3.6.1.4.1.20992.2.15
mbr1400v2	1.3.6.1.4.1.20992.2.16
cba750b	1.3.6.1.4.1.20992.2.17
aer2100	1.3.6.1.4.1.20992.2.18
ibr1150	1.3.6.1.4.1.20992.2.19
ibr1100	1.3.6.1.4.1.20992.2.20
cba850	1.3.6.1.4.1.20992.2.21
ibr350	1.3.6.1.4.1.20992.2.22
aer3100	1.3.6.1.4.1.20992.2.23
aer1600	1.3.6.1.4.1.20992.2.24
ibr650b	1.3.6.1.4.1.20992.2.25
aer3150	1.3.6.1.4.1.20992.2.26
aer1650	1.3.6.1.4.1.20992.2.27
aer2150	1.3.6.1.4.1.20992.2.28
ibr600b	1.3.6.1.4.1.20992.2.29
ibr950	1.3.6.1.4.1.20992.2.30
ibr900	1.3.6.1.4.1.20992.2.31

RFC description

Cradlepoint proprietary MIB for managing SNMP settings and device monitoring on Cradlepoint network devices. Includes objects for firmware version, firmware upgrade control, CPU utilization metrics, and WAN status change notifications.

Start monitoring WiPipe cellular router, M2M/IoT cellular gateway (firmware-upgrade/GPIO-alarm/modem-table status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download WIPIPE-MIB

What Is WIPIPE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description