WILAN-120-58-MIB

All MIBs › WILAN-120-58-MIB

Category: Generic Wireless and Broadband

Description: Manages WiLAN 120/5.8 GHz broadband wireless bridge link status, RF parameters, and throughput statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is WILAN-120-58-MIB?

WILAN-120-58-MIB is a private enterprise MIB from WiLAN (awe120-58) for managing their 120 series 5.8 GHz fixed-wireless broadband bridge/link equipment. It exposes basic device identity and configuration objects — serialNumber, productionDate, macAddress, systemName, unitLocation, contactName — alongside IP addressing configuration (ipAddress, ipNewAddress, ipSubnetMask) and a set of numbered configuration parameters (config7-config9) presumably covering RF link settings. While the visible sample objects lean toward identity/configuration rather than deep runtime telemetry, radio-bridge MIBs of this era typically also carry RF signal quality, link status, and throughput statistics under the broader config/awe120-58 subtree, making this fundamentally a wireless-link health and configuration MIB. It is a self-contained private enterprise MIB with no notable dependency beyond the standard SNMP SMI. It is deployed on WiLAN 120-5.8GHz point-to-point or point-to-multipoint wireless bridge units used for last-mile broadband wireless links, making WILAN-120-58-MIB SNMP monitoring a practical way to track bridge identity and link configuration in the field.

IPNetwork Monitor allows you to monitor SNMP objects defined in WILAN-120-58-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

WiLAN 120/5.8GHz fixed wireless broadband bridge

Monitoring Examples

An admin would poll systemName, unitLocation, and serialNumber to inventory a fielded WiLAN bridge unit, and check ipAddress/ipSubnetMask to confirm correct network configuration after a firmware or config change. The numbered config7/config8/config9 objects would typically hold RF link parameters (e.g. frequency, power, or link-quality settings) that, if drifted from expected values, would explain a degraded wireless link. Given the limited sample objects shown, actual signal/throughput statistics likely live elsewhere in the awe120-58 tree not captured here.

What Can Be Monitored

device serial number and production date
system name and location identity
IP address and subnet configuration
RF/link configuration parameters

Imported Objects

From RFC1155-SMI

Counter
Gauge
enterprises

From RFC1213-MIB

DisplayString
PhysAddress

From SNMPv2-SMI

IpAddress
OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
wilan	1.3.6.1.4.1.2686
awe120_58	1.3.6.1.4.1.2686.2
config	1.3.6.1.4.1.2686.2.1
STR serialNumber	1.3.6.1.4.1.2686.2.1.1	DisplayString	read-only	Unit Serial Number
STR productionDate	1.3.6.1.4.1.2686.2.1.2	DisplayString	read-only	Unit Date of Manufacture
PHY macAddress	1.3.6.1.4.1.2686.2.1.3	PhysAddress	read-only	Ethernet MAC address
STR systemName	1.3.6.1.4.1.2686.2.1.4	DisplayString	read-only	System Name
STR unitLocation	1.3.6.1.4.1.2686.2.1.5	DisplayString	read-only	Unit Location
STR contactName	1.3.6.1.4.1.2686.2.1.6	DisplayString	read-only	Contact Name
INT config7	1.3.6.1.4.1.2686.2.1.7	INTEGER	read-write	Spare
INT config8	1.3.6.1.4.1.2686.2.1.8	INTEGER	read-write	Spare
INT config9	1.3.6.1.4.1.2686.2.1.9	INTEGER	read-write	Spare
IP ipAddress	1.3.6.1.4.1.2686.2.1.10	IpAddress	read-only	Internet IP Address
IP ipNewAddress	1.3.6.1.4.1.2686.2.1.11	IpAddress	read-write	Internet IP Address
IP ipSubnetMask	1.3.6.1.4.1.2686.2.1.12	IpAddress	read-write	IP Subnet Mask
IP ipGatewayAddr	1.3.6.1.4.1.2686.2.1.13	IpAddress	read-write	IP Default Gateway Address (currently unused)
IP ipNetmanAddr	1.3.6.1.4.1.2686.2.1.14	IpAddress	read-write	SNMP Network Management Station IP Address
INT ipPacketFiltering	1.3.6.1.4.1.2686.2.1.15	INTEGER	read-write	IP Packet Filtering: Disabled, Enabled
INT ipAddressFiltering	1.3.6.1.4.1.2686.2.1.16	INTEGER	read-write	IP Address Filtering: Disabled, Enabled
INT ipFilter1Range	1.3.6.1.4.1.2686.2.1.17	INTEGER	read-write	IP Address Filter 1 Range
IP ipFilter1Base	1.3.6.1.4.1.2686.2.1.18	IpAddress	read-write	IP Filter 1 Base Address
INT ipFilter2Range	1.3.6.1.4.1.2686.2.1.19	INTEGER	read-write	IP Address Filter 2 Range
IP ipFilter2Base	1.3.6.1.4.1.2686.2.1.20	IpAddress	read-write	IP Filter 2 Base Address
INT ipFilter3Range	1.3.6.1.4.1.2686.2.1.21	INTEGER	read-write	IP Address Filter 3 Range
IP ipFilter3Base	1.3.6.1.4.1.2686.2.1.22	IpAddress	read-write	IP Filter 3 Base Address
INT ipFilter4Range	1.3.6.1.4.1.2686.2.1.23	INTEGER	read-write	IP Address Filter 4 Range
IP ipFilter4Base	1.3.6.1.4.1.2686.2.1.24	IpAddress	read-write	IP Filter 4 Base Address
INT ipFilter5Range	1.3.6.1.4.1.2686.2.1.25	INTEGER	read-write	IP Address Filter 5 Range
IP ipFilter5Base	1.3.6.1.4.1.2686.2.1.26	IpAddress	read-write	IP Filter 5 Base Address
INT macFilterEntryAge	1.3.6.1.4.1.2686.2.1.27	INTEGER	read-write	MAC Filter Entry Age Time Minutes (1-60)
INT config28	1.3.6.1.4.1.2686.2.1.28	INTEGER	read-write	Spare
INT config29	1.3.6.1.4.1.2686.2.1.29	INTEGER	read-write	Spare
INT stationType	1.3.6.1.4.1.2686.2.1.30	INTEGER	read-only	Current Station Type
INT stationRank	1.3.6.1.4.1.2686.2.1.31	INTEGER	read-only	Current Station RF Rank
INT centerFreq	1.3.6.1.4.1.2686.2.1.32	INTEGER	read-only	Current RF Center Frequency (57410 - 58338)
INT securityWord1	1.3.6.1.4.1.2686.2.1.33	INTEGER	read-only	Current RF Security Password 1
INT securityWord2	1.3.6.1.4.1.2686.2.1.34	INTEGER	read-only	Current RF Security Password 2
INT securityWord3	1.3.6.1.4.1.2686.2.1.35	INTEGER	read-only	Current RF Security Password 3
INT securityWord4	1.3.6.1.4.1.2686.2.1.36	INTEGER	read-only	Current RF Security Password 4
INT securityWord5	1.3.6.1.4.1.2686.2.1.37	INTEGER	read-only	Current RF Security Password 5
INT scramblingCode	1.3.6.1.4.1.2686.2.1.38	INTEGER	read-only	Current RF Scrambling Code Word
INT acquisitionCode	1.3.6.1.4.1.2686.2.1.39	INTEGER	read-only	Current RF Acquisition Code
INT configMinutes	1.3.6.1.4.1.2686.2.1.40	INTEGER	read-only	Current RF Configuration Test Minutes
INT repeaterMode	1.3.6.1.4.1.2686.2.1.41	INTEGER	read-only	Current Base Station Repeater Mode (Disabled, Enabled)
INT systemType	1.3.6.1.4.1.2686.2.1.42	INTEGER	read-only	Current Base Station Symmetry Type (Asymmetric, Symmetric)
INT remoteGroup	1.3.6.1.4.1.2686.2.1.43	INTEGER	read-only	Current RF Group Identifier
INT numOfPollRounds	1.3.6.1.4.1.2686.2.1.44	INTEGER	read-only	Current Number of Polling Rounds (1-60)
INT txPwrLevelAdj	1.3.6.1.4.1.2686.2.1.45	INTEGER	read-only	Current RF Tx Power Level Adjust (-31 to 0) dB
INT defStationType	1.3.6.1.4.1.2686.2.1.46	INTEGER	read-only	Default Station Type
INT defStationRank	1.3.6.1.4.1.2686.2.1.47	INTEGER	read-only	Default Station RF Rank
INT defCenterFreq	1.3.6.1.4.1.2686.2.1.48	INTEGER	read-only	Current RF Center Frequency (57410 - 58338)
INT defSecurityWord1	1.3.6.1.4.1.2686.2.1.49	INTEGER	read-only	Default RF Security Password 1
INT defSecurityWord2	1.3.6.1.4.1.2686.2.1.50	INTEGER	read-only	Default RF Security Password 2
INT defSecurityWord3	1.3.6.1.4.1.2686.2.1.51	INTEGER	read-only	Default RF Security Password 3
INT defSecurityWord4	1.3.6.1.4.1.2686.2.1.52	INTEGER	read-only	Default RF Security Password 4
INT defSecurityWord5	1.3.6.1.4.1.2686.2.1.53	INTEGER	read-only	Default RF Security Password 5
INT defScramblingCode	1.3.6.1.4.1.2686.2.1.54	INTEGER	read-only	Default RF Scrambling Code Word
INT defAcquisitionCode	1.3.6.1.4.1.2686.2.1.55	INTEGER	read-only	Default RF Acquisition Code
INT defConfigMinutes	1.3.6.1.4.1.2686.2.1.56	INTEGER	read-only	Default RF Configuration Test Minutes
INT defRepeaterMode	1.3.6.1.4.1.2686.2.1.57	INTEGER	read-only	Default Base Station Repeater Mode (Disabled, Enabled)
INT defSystemType	1.3.6.1.4.1.2686.2.1.58	INTEGER	read-only	Default Base Station Symmetry Type (Asymmetric, Symmetric)
INT defRemoteGroup	1.3.6.1.4.1.2686.2.1.59	INTEGER	read-only	Default RF Group Identifier
INT defNumOfPollRounds	1.3.6.1.4.1.2686.2.1.60	INTEGER	read-only	Default Number of Polling Rounds (1-60)
INT defTxPwrLevelAdj	1.3.6.1.4.1.2686.2.1.61	INTEGER	read-only	Default RF Tx Power Level Adjust (-31 to 0) dB
INT newStationType	1.3.6.1.4.1.2686.2.1.62	INTEGER	read-write	New Station Type
INT newStationRank	1.3.6.1.4.1.2686.2.1.63	INTEGER	read-write	New Station RF Rank
INT newCenterFreq	1.3.6.1.4.1.2686.2.1.64	INTEGER	read-write	Current RF Center Frequency (57410 - 58338)
INT newSecurityWord1	1.3.6.1.4.1.2686.2.1.65	INTEGER	read-write	New RF Security Password 1
INT newSecurityWord2	1.3.6.1.4.1.2686.2.1.66	INTEGER	read-write	New RF Security Password 2
INT newSecurityWord3	1.3.6.1.4.1.2686.2.1.67	INTEGER	read-write	New RF Security Password 3
INT newSecurityWord4	1.3.6.1.4.1.2686.2.1.68	INTEGER	read-write	New RF Security Password 4
INT newSecurityWord5	1.3.6.1.4.1.2686.2.1.69	INTEGER	read-write	New RF Security Password 5
INT newScramblingCode	1.3.6.1.4.1.2686.2.1.70	INTEGER	read-write	New RF Scrambling Code Word
INT newAcquisitionCode	1.3.6.1.4.1.2686.2.1.71	INTEGER	read-write	New RF Acquisition Code
INT newConfigMinutes	1.3.6.1.4.1.2686.2.1.72	INTEGER	read-write	RF New Configuration Test Minutes
INT newRepeaterMode	1.3.6.1.4.1.2686.2.1.73	INTEGER	read-write	New Base Station Repeater Mode (Disabled, Enabled)
INT newSystemType	1.3.6.1.4.1.2686.2.1.74	INTEGER	read-write	New Base Station Symmetry Type (Asymmetric, Symmetric)
INT newRemoteGroup	1.3.6.1.4.1.2686.2.1.75	INTEGER	read-write	New RF Group Identifier
INT newNumOfPollRounds	1.3.6.1.4.1.2686.2.1.76	INTEGER	read-write	New Number of Polling Rounds (1-60)
INT newTxPwrLevelAdj	1.3.6.1.4.1.2686.2.1.77	INTEGER	read-write	New RF Tx Power Level Adjust (-31 to 0) dB
INT stationMode	1.3.6.1.4.1.2686.2.1.78	INTEGER	read-write	Operating Mode (Normal, Rx-Test, Tx-Test, RSSI-Test)
INT rfTransmitStatus	1.3.6.1.4.1.2686.2.1.79	INTEGER	read-write	RF Transmit Status (Blocked, Unblocked)
INT linkMonitorPeriod	1.3.6.1.4.1.2686.2.1.80	INTEGER	read-write	Link Monitor Period (0=OFF, 1-10000)
INT testModeTimer	1.3.6.1.4.1.2686.2.1.81	INTEGER	read-write	Test Mode Timer Minutes (0=OFF, 1-1000)
INT remoteDistance	1.3.6.1.4.1.2686.2.1.82	INTEGER	read-write	Maximum Remote Distance
INT linkMonitorRank	1.3.6.1.4.1.2686.2.1.83	INTEGER	read-write	Link Monitor Remote Station Rank (1-1000)
INT throttleEnable	1.3.6.1.4.1.2686.2.1.84	INTEGER	read-write	Throttling Enable
INT throttleLevel	1.3.6.1.4.1.2686.2.1.85	INTEGER	read-write	Throttle Level (1-50)
INT config86	1.3.6.1.4.1.2686.2.1.86	INTEGER	read-write	Spare
INT config87	1.3.6.1.4.1.2686.2.1.87	INTEGER	read-write	Spare
INT config88	1.3.6.1.4.1.2686.2.1.88	INTEGER	read-write	Spare
INT config89	1.3.6.1.4.1.2686.2.1.89	INTEGER	read-write	Spare
STR communityName1	1.3.6.1.4.1.2686.2.1.90	DisplayString	read-write	Read-Only Access Community Name
STR communityName2	1.3.6.1.4.1.2686.2.1.91	DisplayString	read-write	Read-Write Access Community Name
INT ethernetAccess	1.3.6.1.4.1.2686.2.1.92	INTEGER	read-only	Ethernet Access to Local Host
INT wirelessAccess	1.3.6.1.4.1.2686.2.1.93	INTEGER	read-only	Ethernet Access to Local Host
INT config94	1.3.6.1.4.1.2686.2.1.94	INTEGER	read-write	Spare
STR currentImage	1.3.6.1.4.1.2686.2.1.95	DisplayString	read-only	Current System Image File Name
STR defaultImage	1.3.6.1.4.1.2686.2.1.96	DisplayString	read-write	Select Specified System Image As Default
STR prevDefaultImage	1.3.6.1.4.1.2686.2.1.97	DisplayString	read-only	Previous Default System Image File Name
INT config98	1.3.6.1.4.1.2686.2.1.98	INTEGER	read-write	Spare
INT config99	1.3.6.1.4.1.2686.2.1.99	INTEGER	read-write	Spare
systemImageList	1.3.6.1.4.1.2686.2.1.100		not-accessible	System Image List
systemImageEntry	1.3.6.1.4.1.2686.2.1.100.1		not-accessible	System Image List Entry
INT systemImageNumber	1.3.6.1.4.1.2686.2.1.100.1.1	INTEGER	read-only	System Image Number
STR systemImageName	1.3.6.1.4.1.2686.2.1.100.1.2	DisplayString	read-only	System Image File Name
STR systemImageRevn	1.3.6.1.4.1.2686.2.1.100.1.3	DisplayString	read-only	System Image Revision Identifier
STR systemImageDate	1.3.6.1.4.1.2686.2.1.100.1.4	DisplayString	read-only	System Image File Date
STR systemImageTime	1.3.6.1.4.1.2686.2.1.100.1.5	DisplayString	read-only	System Image File Time
INT systemImageSize	1.3.6.1.4.1.2686.2.1.100.1.6	INTEGER	read-only	System Image File Size
STR systemImageText	1.3.6.1.4.1.2686.2.1.100.1.7	DisplayString	read-only	System Image Descriptive Text
INT config101	1.3.6.1.4.1.2686.2.1.101	INTEGER	read-write	Spare
INT config102	1.3.6.1.4.1.2686.2.1.102	INTEGER	read-write	Spare
INT config103	1.3.6.1.4.1.2686.2.1.103	INTEGER	read-write	Spare
INT config104	1.3.6.1.4.1.2686.2.1.104	INTEGER	read-write	Spare
status	1.3.6.1.4.1.2686.2.2
CTR totalHours	1.3.6.1.4.1.2686.2.2.1	Counter	read-only	Cumulative Run-Time Hours
CTR systemHours	1.3.6.1.4.1.2686.2.2.2	Counter	read-only	Current Run-Time Hours Since Powerup
CTR loginOkays	1.3.6.1.4.1.2686.2.2.3	Counter	read-only	Number of Successful Logins
CTR loginFails	1.3.6.1.4.1.2686.2.2.4	Counter	read-only	Number of Unsuccessful Login Attempts
INT localUser	1.3.6.1.4.1.2686.2.2.5	INTEGER	read-only	Local User Login Status
INT telnetUser	1.3.6.1.4.1.2686.2.2.6	INTEGER	read-only	Telnet User Login Status
INT ftpUser	1.3.6.1.4.1.2686.2.2.7	INTEGER	read-only	FTP User Login Status
statistics	1.3.6.1.4.1.2686.2.3
CTR etherRxTotalPkts	1.3.6.1.4.1.2686.2.3.1	Counter	read-only	Total Ethernet Packets Received
CTR etherRxLocalPkts	1.3.6.1.4.1.2686.2.3.2	Counter	read-only	Ethernet Packets Received For Local Host
CTR etherRxErrorPkts	1.3.6.1.4.1.2686.2.3.3	Counter	read-only	Ethernet Receive Error Packets
CTR etherRxDroppedPkts	1.3.6.1.4.1.2686.2.3.4	Counter	read-only	Ethernet Receive Packets Dropped
CTR etherRxDiscardPkts	1.3.6.1.4.1.2686.2.3.5	Counter	read-only	Ethernet Receive Packets Discarded
CTR etherRxTotalKbytes	1.3.6.1.4.1.2686.2.3.6	Counter	read-only	Total Ethernet KBytes Received Since Last Reset
CTR etherRxBcastKbytes	1.3.6.1.4.1.2686.2.3.7	Counter	read-only	Ethernet Broadcast KBytes Received Since Last Reset
CTR etherTxTotalPkts	1.3.6.1.4.1.2686.2.3.8	Counter	read-only	Total Ethernet Packets Transmitted
CTR etherTxDroppedPkts	1.3.6.1.4.1.2686.2.3.9	Counter	read-only	Ethernet Transmit Packets Dropped
CTR etherTxTotalKbytes	1.3.6.1.4.1.2686.2.3.10	Counter	read-only	Total Ethernet KBytes Transmitted Since Last Reset
CTR etherTxBcastKbytes	1.3.6.1.4.1.2686.2.3.11	Counter	read-only	Ethernet Broadcast KBytes Transmitted Since Last Reset
CTR rfRxTotalPkts	1.3.6.1.4.1.2686.2.3.12	Counter	read-only	Total RF Receive Packets
CTR rfRxLocalPkts	1.3.6.1.4.1.2686.2.3.13	Counter	read-only	RF Packets Received For Local Host
CTR rfRxDroppedPkts	1.3.6.1.4.1.2686.2.3.14	Counter	read-only	RF Receive Packets Dropped
CTR rfRxDiscardedPkts	1.3.6.1.4.1.2686.2.3.15	Counter	read-only	RF Receive Packets Discarded
CTR rfTxTotalPkts	1.3.6.1.4.1.2686.2.3.16	Counter	read-only	Total RF Transmitted Packets
CTR rfTxLocalPkts	1.3.6.1.4.1.2686.2.3.17	Counter	read-only	RF Local Transmit Packets
CTR rfTxDroppedPkts	1.3.6.1.4.1.2686.2.3.18	Counter	read-only	RF Transmit Packets Dropped
CTR rfRxSframeCount	1.3.6.1.4.1.2686.2.3.19	Counter	read-only	Total RF Super Frames Received
CTR rfRxOverrunErrors	1.3.6.1.4.1.2686.2.3.20	Counter	read-only	RF Overrun Errors
CTR rfRxSFrameErrors	1.3.6.1.4.1.2686.2.3.21	Counter	read-only	RF Super Frame Control Word Errors
CTR rfRxChecksumErrors	1.3.6.1.4.1.2686.2.3.22	Counter	read-only	RF Super Frame Header Checksum Errors
CTR rfRxPacketErrors	1.3.6.1.4.1.2686.2.3.23	Counter	read-only	RF Packet Control Word Errors
CTR rfRxLengthErrors	1.3.6.1.4.1.2686.2.3.24	Counter	read-only	RF Super Frame Length Errors
CTR rfTxSuperFrameCnt	1.3.6.1.4.1.2686.2.3.25	Counter	read-only	RF Super Frames Transmitted
CTR rfEtoIThroughput	1.3.6.1.4.1.2686.2.3.26	Counter	read-only	Ethernet to RF Throughput in bits/s
CTR rfItoEThroughput	1.3.6.1.4.1.2686.2.3.27	Counter	read-only	RF to Ethernet Throughput in bits/s
CTR statistics24	1.3.6.1.4.1.2686.2.3.28	Counter	read-only	Spare
INT linkMonitorRank1	1.3.6.1.4.1.2686.2.3.29	INTEGER	read-only	Link Monitor Remote Station Rank
STR linkMonRtoBber	1.3.6.1.4.1.2686.2.3.30	DisplayString	read-only	Link Monitor Remote To Base BER
STR linkMonBtoRber	1.3.6.1.4.1.2686.2.3.31	DisplayString	read-only	Link Monitor Base to Remote BER
CTR linkMonMissPktCnt	1.3.6.1.4.1.2686.2.3.32	Counter	read-only	Link Monitor Missed Packet Count
INT linkMonEnvPBtoR	1.3.6.1.4.1.2686.2.3.33	INTEGER	read-only	Link Monitor Base to Remote Envelope Power
INT linkMonEnvPRtoB	1.3.6.1.4.1.2686.2.3.34	INTEGER	read-only	Link Monitor Remote to Base Envelope Power
INT linkMonCorrPBtoR	1.3.6.1.4.1.2686.2.3.35	INTEGER	read-only	Link Monitor Base to Remote Correlation Power
INT linkMonCorrPRtoB	1.3.6.1.4.1.2686.2.3.36	INTEGER	read-only	Link Monitor Remote to Base Correlation Power
commands	1.3.6.1.4.1.2686.2.4
INT rebootCurrent	1.3.6.1.4.1.2686.2.4.1	INTEGER	read-write	Reboot Current System Image
STR rebootImage	1.3.6.1.4.1.2686.2.4.2	DisplayString	read-write	Reboot Specified System Image
INT rebootNewRfConfig	1.3.6.1.4.1.2686.2.4.3	INTEGER	read-write	Reboot New RF Configuration
INT restFactConfReboot	1.3.6.1.4.1.2686.2.4.4	INTEGER	read-write	Restore Factory Configuration and Reboot
INT saveConfToFlash	1.3.6.1.4.1.2686.2.4.5	INTEGER	read-write	Save Current Configuration To Flash
INT resetRadioStats	1.3.6.1.4.1.2686.2.4.6	INTEGER	read-write	Reset Radio Statistics
INT resetEthernetStats	1.3.6.1.4.1.2686.2.4.7	INTEGER	read-write	Reset Ethernet Statistics

RFC description

Manages Wi-LAN AWE 120-58 broadband wireless equipment with configuration and monitoring capabilities.

Start monitoring WiLAN 120/5.8GHz fixed wireless broadband bridge (identity/IP-config/RF-link status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download WILAN-120-58-MIB

What Is WILAN-120-58-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description