All MIBs › TN-QOS-EXT-MIB
Organization: Transition Networks, Inc.
Last Updated: 2014-00-06
Category: QoS, Transition Networks Media Converters
Description: Manages Transition Networks QoS policy extension attributes and extended queue parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TN-QOS-EXT-MIB?
TN-QOS-EXT-MIB is a Transition Networks proprietary SNMP MIB extending base QoS capability with additional per-port and per-queue policing controls not covered by standard QoS MIBs. It exposes a port-level policer table (rate, unit, flow-control behavior, enable status) and a per-queue policer table keyed by queue ID, letting an operator cap traffic at both the physical port and individual priority-queue level. It's mainly a configuration MIB, but the policer status objects support monitoring the software status of traffic shaping: confirming a policer is actually enabled and active where intended, essential for diagnosing unexpected packet drops or throughput caps. No dependency on other standard MIBs is evident, though it complements standard bridge/QoS MIBs already present on the switch for classification. It is deployed on Transition Networks managed switches in networks needing granular traffic-rate enforcement per port or per class of service, making the TN-QOS-EXT-MIB reference useful for confirming policer configuration at both levels.
IPNetwork Monitor allows you to monitor SNMP objects defined in TN-QOS-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Transition Networks managed switch
Monitoring Examples
An operator polls tnQosExtPortPolicerTable/tnQosExtPortPolicerEntry to check tnQosExtPortPolicerStatus and tnQosExtPortPolicerRate/Unit, confirming a port is capped at the intended bandwidth and that tnQosExtPortPolicerFlowControl behavior matches policy (drop vs. pause). tnQosExtPortQueuePolicerTable/tnQosExtPortQueuePolicerEntry is checked per tnQosExtPortQueuePolicerQid to verify individual queue-level rate limits, useful when diagnosing why a specific traffic class is experiencing more drops than the overall port policer alone would explain.
What Can Be Monitored
- port policer enable status and rate
- per-queue policer enable status and rate
- flow-control behavior under policing
This MIB depends on
Related MIBs
Imported Objects
From ENTITY-MIB
| entPhysicalIndex | OBJECT-TYPE |
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero | |
| ifIndex | OBJECT-TYPE |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From Q-BRIDGE-MIB
| PortList | |
| VlanIndex |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| MacAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeInterval | |
| TruthValue |
From TRANSITION-SMI
| tnProducts | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| tnQosExtMIB | 1.3.6.1.4.1.868.2.5.9 | The mib module for managing extra QoS features in TN platform products. | ||
| tnQosExtMIBObjects | 1.3.6.1.4.1.868.2.5.9.1 | |||
| tnQosExtPortMgmt | 1.3.6.1.4.1.868.2.5.9.1.1 | |||
| tnQosExtPortPolicerTable | 1.3.6.1.4.1.868.2.5.9.1.1.1 | not-accessible | A port policer table can limit the bandwidth of received frames per port. | |
| tnQosExtPortPolicerEntry | 1.3.6.1.4.1.868.2.5.9.1.1.1.1 | not-accessible | An entry in the table controls the bandwidth of received frames per port. It is located in front of the ingress queue. | |
| INT tnQosExtPortPolicerStatus | 1.3.6.1.4.1.868.2.5.9.1.1.1.1.1 | INTEGER | read-write | Controls the per port policer status. The policer can limit the bandwidth of received frames. It is located in front of the Ingress queue. |
| INT tnQosExtPortPolicerRate | 1.3.6.1.4.1.868.2.5.9.1.1.1.1.2 | INTEGER | read-write | Controls the rate for the port policer. The rate unit is defined in tnQosExtPortPolicerUnit. |
| TNQ tnQosExtPortPolicerUnit | 1.3.6.1.4.1.868.2.5.9.1.1.1.1.3 | TnQosExtRateUnitType | read-write | the rate unit for the port policer. Depend on the implement, some unit type may not be supported. |
| INT tnQosExtPortPolicerFlowControl | 1.3.6.1.4.1.868.2.5.9.1.1.1.1.4 | INTEGER | read-write | Controls the port policer flow control. If policer flow control is enabled and the port is in flow control mode, then pause frames are sent instead of discarding frames. |
| tnQosExtPortQueuePolicerTable | 1.3.6.1.4.1.868.2.5.9.1.1.2 | not-accessible | A port queue policer table can limit the bandwidth of received frames per port per queue. | |
| tnQosExtPortQueuePolicerEntry | 1.3.6.1.4.1.868.2.5.9.1.1.2.1 | not-accessible | An entry in the table controls the bandwidth of received frames per port per queue. It is located in front of the ingress queue. | |
| INT tnQosExtPortQueuePolicerQid | 1.3.6.1.4.1.868.2.5.9.1.1.2.1.1 | INTEGER | not-accessible | The ingress queue id for queue policer. tnQosExtPortQueuePolicerQid is a number in the range (0..(dot1dPortNumTrafficClasses-1)) |
| INT tnQosExtPortQueuePolicerStatus | 1.3.6.1.4.1.868.2.5.9.1.1.2.1.2 | INTEGER | read-write | Controls whether the policer is enabled on the specific queue. |
| INT tnQosExtPortQueuePolicerRate | 1.3.6.1.4.1.868.2.5.9.1.1.2.1.3 | INTEGER | read-write | Controls the rate for the queue policer. The rate unit is defined in tnQosExtPortQueuePolicerUnit. |
| TNQ tnQosExtPortQueuePolicerUnit | 1.3.6.1.4.1.868.2.5.9.1.1.2.1.4 | TnQosExtRateUnitType | read-write | The rate unit for the queue policer. Depend on the implement, some unit type may not be supported. |
| tnQosExtPortSchedulerTable | 1.3.6.1.4.1.868.2.5.9.1.1.3 | not-accessible | A port scheduler table controls the egress queue scheduler method per port. | |
| tnQosExtPortSchedulerEntry | 1.3.6.1.4.1.868.2.5.9.1.1.3.1 | not-accessible | An entry in the table controls the egress queue scheduler method per port. | |
| INT tnQosExtPortSchedulerMode | 1.3.6.1.4.1.868.2.5.9.1.1.3.1.1 | INTEGER | read-write | Controls the port egress scheduler mode, strict or weighted. |
| BIT tnQosExtPortSchedulerQueueMask | 1.3.6.1.4.1.868.2.5.9.1.1.3.1.2 | Bits | read-write | Controls the queues mask which is in the weighted schedule mode. Other queues are in strict mode. |
| tnQosExtPortSchedulerWeightTable | 1.3.6.1.4.1.868.2.5.9.1.1.4 | not-accessible | A port scheduler weight table controls the egress queue weight value in weighted scheduler mode per port. | |
| tnQosExtPortSchedulerWeightEntry | 1.3.6.1.4.1.868.2.5.9.1.1.4.1 | not-accessible | An entry in the table controls the egress queue weight value in weighted scheduler mode per port. | |
| INT tnQosExtPortSchedulerWeightQid | 1.3.6.1.4.1.868.2.5.9.1.1.4.1.1 | INTEGER | not-accessible | The egress queue id for scheduler. tnQosExtPortSchedulerWeightQid is a number in the range (0..(dot1dPortNumTrafficClasses-1)) |
| INT tnQosExtPortSchedulerWeightVal | 1.3.6.1.4.1.868.2.5.9.1.1.4.1.2 | INTEGER | read-write | The egress queue weight value. the value range is from 1 to 100. |
| INT tnQosExtPortSchedulerWeightPercent | 1.3.6.1.4.1.868.2.5.9.1.1.4.1.3 | INTEGER | read-only | The egress queue weight in percent view. |
| tnQosExtPortShaperTable | 1.3.6.1.4.1.868.2.5.9.1.1.5 | not-accessible | A port shaper table can limit the bandwidth of egress frames per port. | |
| tnQosExtPortShaperEntry | 1.3.6.1.4.1.868.2.5.9.1.1.5.1 | not-accessible | An entry in the table controls the bandwidth of egress frames per port. | |
| INT tnQosExtPortShaperStatus | 1.3.6.1.4.1.868.2.5.9.1.1.5.1.1 | INTEGER | read-write | Controls the per port shaper status. The shaper can limit the bandwidth of transmit frames in egress side. |
| INT tnQosExtPortShaperRate | 1.3.6.1.4.1.868.2.5.9.1.1.5.1.2 | INTEGER | read-write | Controls the rate for the port shaper. The rate unit is defined in tnQosExtPortShaperUnit. |
| TNQ tnQosExtPortShaperUnit | 1.3.6.1.4.1.868.2.5.9.1.1.5.1.3 | TnQosExtRateUnitType | read-write | the rate unit for the port shaper. Depend on the implement, some unit type may not be supported. |
| tnQosExtPortQueueShaperTable | 1.3.6.1.4.1.868.2.5.9.1.1.6 | not-accessible | A port queue shaper table can limit the bandwidth of egress frames per port per queue. | |
| tnQosExtPortQueueShaperEntry | 1.3.6.1.4.1.868.2.5.9.1.1.6.1 | not-accessible | An entry in the table controls the bandwidth of egress frames per port per queue. | |
| INT tnQosExtPortQueueShaperQid | 1.3.6.1.4.1.868.2.5.9.1.1.6.1.1 | INTEGER | not-accessible | The egress queue id for queue shaper. tnQosExtPortQueueShaperQid is a number in the range (0..(dot1dPortNumTrafficClasses-1)) |
| INT tnQosExtPortQueueShaperStatus | 1.3.6.1.4.1.868.2.5.9.1.1.6.1.2 | INTEGER | read-write | Controls whether the shaper is enabled on the specific queue. |
| INT tnQosExtPortQueueShaperRate | 1.3.6.1.4.1.868.2.5.9.1.1.6.1.3 | INTEGER | read-write | Controls the rate for the queue shaper. The rate unit is defined in tnQosExtPortQueueShaperUnit. |
| TNQ tnQosExtPortQueueShaperUnit | 1.3.6.1.4.1.868.2.5.9.1.1.6.1.4 | TnQosExtRateUnitType | read-write | The rate unit for the queue shaper. Depend on the implement, some unit type may not be supported. |
| INT tnQosExtPortQueueShaperExcess | 1.3.6.1.4.1.868.2.5.9.1.1.6.1.5 | INTEGER | read-write | Controls whether the queue is allowed to use excess bandwidth. |
| tnQosExtPortStormControlTable | 1.3.6.1.4.1.868.2.5.9.1.1.7 | not-accessible | Storm control settings table. | |
| tnQosExtPortStormControlEntry | 1.3.6.1.4.1.868.2.5.9.1.1.7.1 | not-accessible | An entry in the table represents the storm control settings on an interface. | |
| INT tnQosExtPortStormControlUnicastStatus | 1.3.6.1.4.1.868.2.5.9.1.1.7.1.1 | INTEGER | read-write | Enable or disable the storm control status for unicast. |
| TNQ tnQosExtPortStormControlUnicastRate | 1.3.6.1.4.1.868.2.5.9.1.1.7.1.2 | TnQosExtRateInFps | read-write | The rate unit is packets per second (pps). |
| INT tnQosExtPortStormControlMulticastStatus | 1.3.6.1.4.1.868.2.5.9.1.1.7.1.3 | INTEGER | read-write | Enable or disable the storm control status for multicast. |
| TNQ tnQosExtPortStormControlMulticastRate | 1.3.6.1.4.1.868.2.5.9.1.1.7.1.4 | TnQosExtRateInFps | read-write | The rate unit is packets per second (pps). |
| INT tnQosExtPortStormControlBroadcastStatus | 1.3.6.1.4.1.868.2.5.9.1.1.7.1.5 | INTEGER | read-write | Enable or disable the storm control status for broadcast. |
| TNQ tnQosExtPortStormControlBroadcastRate | 1.3.6.1.4.1.868.2.5.9.1.1.7.1.6 | TnQosExtRateInFps | read-write | The rate unit is packets per second (pps). |
| tnQosExtPortStormControl2Table | 1.3.6.1.4.1.868.2.5.9.1.1.8 | not-accessible | Storm control settings table 2. | |
| tnQosExtPortStormControl2Entry | 1.3.6.1.4.1.868.2.5.9.1.1.8.1 | not-accessible | An entry in the table represents the storm control settings on an interface. | |
| INT tnQosExtPortStormControl2FrameType | 1.3.6.1.4.1.868.2.5.9.1.1.8.1.1 | INTEGER | not-accessible | The frame type that storm control takes effect. Implement may use values like: unicast - unicast frame broadcast - broadcast frame unknown - unknown(flooding) frame |
| INT tnQosExtPortStormControl2Rate | 1.3.6.1.4.1.868.2.5.9.1.1.8.1.2 | INTEGER | read-write | Controls the rate for the storm control. The rate unit is defined in tnQosExtPortStormControl2RateUnit |
| TNQ tnQosExtPortStormControl2RateUnit | 1.3.6.1.4.1.868.2.5.9.1.1.8.1.3 | TnQosExtRateUnitType | read-write | Controls the rate unit for the storm control. The rate is defined in tnQosExtPortStormControl2Rate |
| T/F tnQosExtPortStormControl2Status | 1.3.6.1.4.1.868.2.5.9.1.1.8.1.4 | TruthValue | read-write | Enable or disable the storm control status for the certain frame type. |
| tnQosExtPortWredTable | 1.3.6.1.4.1.868.2.5.9.1.1.9 | not-accessible | A table used to configure the Weighted Random Early Detection feature. | |
| tnQosExtPortWredEntry | 1.3.6.1.4.1.868.2.5.9.1.1.9.1 | not-accessible | An entry in the table used to configure the Weighted Random Early Detection feature. | |
| INT tnQosExtPortWredQid | 1.3.6.1.4.1.868.2.5.9.1.1.9.1.1 | INTEGER | not-accessible | The queue id for the weighted random early detection. |
| T/F tnQosExtPortWredEnable | 1.3.6.1.4.1.868.2.5.9.1.1.9.1.2 | TruthValue | read-write | Enable or disable the weighted random early detection for a certain traffic queue. |
| INT tnQosExtPortWredThresholdMin | 1.3.6.1.4.1.868.2.5.9.1.1.9.1.3 | INTEGER | read-write | Controls the lower RED threshold for a certain traffic queue. If the average queue filling level is below this threshold, the drop probability is zero. This value is restricted to 0-100. |
| INT tnQosExtPortWredMaxDp1 | 1.3.6.1.4.1.868.2.5.9.1.1.9.1.4 | INTEGER | read-write | Controls the drop probability for frames marked with Drop Precedence Level 1 when the average queue filling level is 100%. This value is restricted to 0-100. |
| INT tnQosExtPortWredMaxDp2 | 1.3.6.1.4.1.868.2.5.9.1.1.9.1.5 | INTEGER | read-write | Controls the drop probability for frames marked with Drop Precedence Level 2 when the average queue filling level is 100%. This value is restricted to 0-100. |
| INT tnQosExtPortWredMaxDp3 | 1.3.6.1.4.1.868.2.5.9.1.1.9.1.6 | INTEGER | read-write | Controls the drop probability for frames marked with Drop Precedence Level 3 when the average queue filling level is 100%. This value is restricted to 0-100. |
| INT tnQosExtPortWredMaxThresh | 1.3.6.1.4.1.868.2.5.9.1.1.9.1.7 | INTEGER | read-write | Controls the upper RED drop probability or fill level threshold for frames marked with Drop Precedence Level 1 (yellow frames). This value is restricted to 1-100%. |
| INT tnQosExtPortWredMaxUnit | 1.3.6.1.4.1.868.2.5.9.1.1.9.1.8 | INTEGER | read-write | Selects the unit for Max. Threshold. Possible values are: Drop Probability: Max. Threshold controls the drop probability just below 100% fill level. Fill Level: Max. Threshold controls the fill level where drop probability reaches 100%. |
| tnQosExtPortPolicerOrderTable | 1.3.6.1.4.1.868.2.5.9.1.1.10 | not-accessible | A table used to configure the QoS Policer Order per port. | |
| tnQosExtPortPolicerOrderEntry | 1.3.6.1.4.1.868.2.5.9.1.1.10.1 | not-accessible | An entry in the table used to configure the QoS Policer Order per port. | |
| INT tnQosExtPortPolicerOrder | 1.3.6.1.4.1.868.2.5.9.1.1.10.1.1 | INTEGER | read-write | QoS policer order on the entry. depend on implement, the valid policer order would be: 1 - in this mode, QoS policer order is Port Queue Policer first, then Port Policer, ACL Policer is the last (default). 2 - in this mode, QoS policer order is ACL Policer first, then Port Queue Policer, Port Policer is the last. |
| tnQosExtL2CosMgmt | 1.3.6.1.4.1.868.2.5.9.1.2 | |||
| tnQosExtL2CosIfClassifDefaultTable | 1.3.6.1.4.1.868.2.5.9.1.2.1 | not-accessible | Qos layer 2 default Ingress Classification table. | |
| tnQosExtL2CosIfClassifDefaultEntry | 1.3.6.1.4.1.868.2.5.9.1.2.1.1 | not-accessible | An entry in the table represents the QoS layer 2 default Ingress Classification settings on an interface. | |
| INT tnQosExtL2CosIfClassifDefaultClass | 1.3.6.1.4.1.868.2.5.9.1.2.1.1.1 | INTEGER | read-write | Controls the default QoS class (the QoS class for frames not classified in any other way). There is a one to one mapping between QoS class, queue and priority. A QoS class of 0 (zero) has the lowest priority. tnQosExtL2CosIfClassifDefaultClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)) |
| INT tnQosExtL2CosIfClassifDefaultDpl | 1.3.6.1.4.1.868.2.5.9.1.2.1.1.2 | INTEGER | read-write | Controls the default DP (Drop Precedence) level for frames not classified in any other way. |
| INT tnQosExtL2CosIfClassifDefaultPcp | 1.3.6.1.4.1.868.2.5.9.1.2.1.1.3 | INTEGER | read-write | Controls the default PCP for untagged frames. PCP (Priority Code Point) is a 3-bit field storing the priority level for the 802.1Q frame. It is also known as User Priority. |
| INT tnQosExtL2CosIfClassifDefaultDei | 1.3.6.1.4.1.868.2.5.9.1.2.1.1.4 | INTEGER | read-write | Controls the default DEI for untagged frames. DEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag. |
| tnQosExtL2CosIfClassifTagTable | 1.3.6.1.4.1.868.2.5.9.1.2.2 | not-accessible | Layer 2 Cos ingress priority-tagged frame classification mode Table. | |
| tnQosExtL2CosIfClassifTagEntry | 1.3.6.1.4.1.868.2.5.9.1.2.2.1 | not-accessible | An entry in the table represents the Layer 2 Cos ingress priority-tagged frame classification mode on an interface. | |
| INT tnQosExtL2CosIfClassifTagMode | 1.3.6.1.4.1.868.2.5.9.1.2.2.1.1 | INTEGER | read-write | Controls the classification mode for priority tagged frames on this interface. Disabled - Use default QoS class and DP level for priority tagged frames. Enabled - Use mapped value of PCP and DEI for priority tagged frames. |
| tnQosExtL2CosIfClassifTagMapTable | 1.3.6.1.4.1.868.2.5.9.1.2.3 | not-accessible | classified (PCP, DEI) to (QoS class, DP level) mapping table. | |
| tnQosExtL2CosIfClassifTagMapEntry | 1.3.6.1.4.1.868.2.5.9.1.2.3.1 | not-accessible | An entry in the table represents the mapping of the classified (PCP, DEI) to (QoS class, DP level) values. This mapping is valid when tnQosExtL2CosIfClassifTagMode is set to Enabled. | |
| INT tnQosExtL2CosIfClassifTagMapPcp | 1.3.6.1.4.1.868.2.5.9.1.2.3.1.1 | INTEGER | not-accessible | The carried Pcp (Priority Code Point) field value if recieved frame is IEEE tagged frame. |
| INT tnQosExtL2CosIfClassifTagMapDei | 1.3.6.1.4.1.868.2.5.9.1.2.3.1.2 | INTEGER | not-accessible | The carried Dei (Drop Eligible Indicator) field value if recieved frame is IEEE tagged frame. |
| INT tnQosExtL2CosIfClassifTagMapClass | 1.3.6.1.4.1.868.2.5.9.1.2.3.1.3 | INTEGER | read-write | The Traffic Class the received frame is mapped to. tnQosExtL2CosIfClassifTagMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)). |
| INT tnQosExtL2CosIfClassifTagMapDpl | 1.3.6.1.4.1.868.2.5.9.1.2.3.1.4 | INTEGER | read-write | The DP (Drop Precedence) level the received frame is mapped to. |
| tnQosExtL2CosIfTagRemarkingModeTable | 1.3.6.1.4.1.868.2.5.9.1.2.4 | not-accessible | A table can control the egress frame tag remarking mode on an interface. | |
| tnQosExtL2CosIfTagRemarkingModeEntry | 1.3.6.1.4.1.868.2.5.9.1.2.4.1 | not-accessible | An entry in the table controls the egress frame tag remarking mode on an interface. | |
| INT tnQosExtL2CosIfTagRemarkingMode | 1.3.6.1.4.1.868.2.5.9.1.2.4.1.1 | INTEGER | read-write | Controls the tag remarking mode for this port. Classified - Use classified PCP/DEI values. Default - Use default PCP/DEI values. Mapped - Use mapped versions of QoS class and DP level. |
| tnQosExtL2CosIfTagRemarkingDefaultTable | 1.3.6.1.4.1.868.2.5.9.1.2.5 | not-accessible | A table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to default mode. | |
| tnQosExtL2CosIfTagRemarkingDefaultEntry | 1.3.6.1.4.1.868.2.5.9.1.2.5.1 | not-accessible | An entry in the table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to default mode. | |
| INT tnQosExtL2CosIfTagRemarkingDefaultPcp | 1.3.6.1.4.1.868.2.5.9.1.2.5.1.1 | INTEGER | read-write | Default PCP (Priority Code Point) is a 3-bit field storing the priority level for the 802.1Q frame. It is also known as User Priority. The valid range is 0 - 7. The default is 0. |
| INT tnQosExtL2CosIfTagRemarkingDefaultDei | 1.3.6.1.4.1.868.2.5.9.1.2.5.1.2 | INTEGER | read-write | Default DEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag. The valid range is 0 - 1. The default is 0. |
| tnQosExtL2CosIfTagRemarkingMappingTable | 1.3.6.1.4.1.868.2.5.9.1.2.6 | not-accessible | A table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode. | |
| tnQosExtL2CosIfTagRemarkingMappingEntry | 1.3.6.1.4.1.868.2.5.9.1.2.6.1 | not-accessible | An entry in the table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode. | |
| INT tnQosExtL2CosIfTagRemarkingClass | 1.3.6.1.4.1.868.2.5.9.1.2.6.1.1 | INTEGER | not-accessible | The traffic class of the transmit frame belongs to. tnQosExtIfTagRemarkingClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)). |
| INT tnQosExtL2CosIfTagRemarkingDpl | 1.3.6.1.4.1.868.2.5.9.1.2.6.1.2 | INTEGER | not-accessible | The DP (Drop Precedence) level of the transmit frame belongs to. |
| INT tnQosExtL2CosIfTagRemarkingPcp | 1.3.6.1.4.1.868.2.5.9.1.2.6.1.3 | INTEGER | read-write | PCP (Priority Code Point) is a 3-bit field storing the priority level for the 802.1Q frame. It is also known as User Priority. The valid range is 0 - 7. |
| INT tnQosExtL2CosIfTagRemarkingDei | 1.3.6.1.4.1.868.2.5.9.1.2.6.1.4 | INTEGER | read-write | DEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag. The valid range is 0 - 1. |
| tnQosExtL2CosIfTagRemarkingDplMappingTable | 1.3.6.1.4.1.868.2.5.9.1.2.7 | not-accessible | A table represents the egress frame tag remarking DP level mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode. | |
| tnQosExtL2CosIfTagRemarkingDplMappingEntry | 1.3.6.1.4.1.868.2.5.9.1.2.7.1 | not-accessible | An entry in the table represents the egress frame tag remarking dpl mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode. | |
| INT tnQosExtL2CosIfTagRemarkingDplMappingClassifDpl | 1.3.6.1.4.1.868.2.5.9.1.2.7.1.1 | INTEGER | not-accessible | The Classified DP (Drop Precedence) level of the transmit frame belongs to. |
| INT tnQosExtL2CosIfTagRemarkingDplMappingDpl | 1.3.6.1.4.1.868.2.5.9.1.2.7.1.2 | INTEGER | read-write | The DP (Drop Precedence) level used for tag remarking process. |
| tnQosExtDscpMgmt | 1.3.6.1.4.1.868.2.5.9.1.3 | |||
| tnQosExtDscpIfClassifBaseTable | 1.3.6.1.4.1.868.2.5.9.1.3.1 | not-accessible | A table represents the QoS classification mode basis on an interface. | |
| tnQosExtDscpIfClassifBaseEntry | 1.3.6.1.4.1.868.2.5.9.1.3.1.1 | not-accessible | An entry in the table represents the QoS classification mode basis on an interface. | |
| INT tnQosExtDscpIfClassifBaseDscp | 1.3.6.1.4.1.868.2.5.9.1.3.1.1.1 | INTEGER | read-write | Controls whether the QoS classification mode is based on DSCP value in IP frames on an interface. Disabled - Disable DSCP based classification. Enabled - Enable DSCP based classification. |
| tnQosExtDscpIfTransTable | 1.3.6.1.4.1.868.2.5.9.1.3.2 | not-accessible | A table represents the DSCP ingress translation mode on an interface. | |
| tnQosExtDscpIfTransEntry | 1.3.6.1.4.1.868.2.5.9.1.3.2.1 | not-accessible | An entry in the table represents the DSCP ingress translation mode on an interface. | |
| INT tnQosExtDscpIfTransMode | 1.3.6.1.4.1.868.2.5.9.1.3.2.1.1 | INTEGER | read-write | Controls the ingress DSCP translation setting on an interface. |
| tnQosExtDscpIfTransMapTable | 1.3.6.1.4.1.868.2.5.9.1.3.3 | not-accessible | A table perform the ingress DSCP translation on an interface. | |
| tnQosExtDscpIfTransMapEntry | 1.3.6.1.4.1.868.2.5.9.1.3.3.1 | not-accessible | A entry in this table perform the ingress DSCP translation on an interface. | |
| INT tnQosExtDscpIfTransMapDscp | 1.3.6.1.4.1.868.2.5.9.1.3.3.1.1 | INTEGER | not-accessible | The received frame carried DSCP value, used for DSCP transmit input. DSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes. The valid range is 0 - 63 |
| INT tnQosExtDscpIfTransMapToDscp | 1.3.6.1.4.1.868.2.5.9.1.3.3.1.2 | INTEGER | read-write | The mapping DSCP value from the frame DSCP value, used for DSCP classification. DSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes. The valid range is 0 - 63 |
| tnQosExtDscpClassifMapTable | 1.3.6.1.4.1.868.2.5.9.1.3.4 | not-accessible | A table represents the DSCP-Based QoS ingress classification mapping on an interface. | |
| tnQosExtDscpClassifMapEntry | 1.3.6.1.4.1.868.2.5.9.1.3.4.1 | not-accessible | An entry in the table represents the DSCP-Based QoS ingress classification mapping on an interface. | |
| INT tnQosExtDscpClassifMapDscp | 1.3.6.1.4.1.868.2.5.9.1.3.4.1.1 | INTEGER | not-accessible | DSCP value used to map Qos class and DPL is either translated DSCP value or incoming frame DSCP value. |
| INT tnQosExtDscpClassifMapTrust | 1.3.6.1.4.1.868.2.5.9.1.3.4.1.2 | INTEGER | read-write | Controls whether a specific DSCP value is trusted. Only frames with trused DSCP values are mapped to a specific QoS class and DPL. Frames with untrusted DSCP values are treated as a non-IP frame. Enabled - Set DSCP as trusted DSCP. Disabled - Set DSCP as un-trusted DSCP. |
| INT tnQosExtDscpClassifMapClass | 1.3.6.1.4.1.868.2.5.9.1.3.4.1.3 | INTEGER | read-write | The traffic class of the recieved frame mapped to. tnQosExtDscpClassifMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)). |
| INT tnQosExtDscpClassifMapDpl | 1.3.6.1.4.1.868.2.5.9.1.3.4.1.4 | INTEGER | read-write | The DP (Drop Precedence) level of the transmit frame mapped to |
| tnQosExtDscpIfClassifExtTable | 1.3.6.1.4.1.868.2.5.9.1.3.5 | not-accessible | A table represents the DSCP classification based on QoS class and DP level on an interface. | |
| tnQosExtDscpIfClassifExtEntry | 1.3.6.1.4.1.868.2.5.9.1.3.5.1 | not-accessible | An entry in the table represents the DSCP classification based on QoS class and DP level on an interface. | |
| INT tnQosExtDscpIfClassifExtMode | 1.3.6.1.4.1.868.2.5.9.1.3.5.1.1 | INTEGER | read-write | Controls the ingress DSCP classification setting on an interface. Disable - No Ingress DSCP Classification. DSCP=0 - Classify if incoming (or translated if enabled) DSCP is 0. Selected: Classify only selected DSCP for which classification is enabled. All: Classify all DSCP. |
| tnQosExtDscpIfClassifExtDscpTable | 1.3.6.1.4.1.868.2.5.9.1.3.6 | not-accessible | A table represents the DSCP classification mode per DSCP value. | |
| tnQosExtDscpIfClassifExtDscpEntry | 1.3.6.1.4.1.868.2.5.9.1.3.6.1 | not-accessible | An entry in the table represents the DSCP classification mode per DSCP value. | |
| INT tnQosExtDscpIfClassifExtDscp | 1.3.6.1.4.1.868.2.5.9.1.3.6.1.1 | INTEGER | not-accessible | DSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes. The valid range is 0 - 63 |
| INT tnQosExtDscpIfClassifExtDscpMode | 1.3.6.1.4.1.868.2.5.9.1.3.6.1.2 | INTEGER | read-write | Control the DSCP ingress classification mode on an interface. If port DSCP classification is 'selected', DSCP will be classified based on QoS class and DP level only for DSCP value with classification mode 'enabled'. DSCP may be translated DSCP if translation is enabled for the port. Enabled - Enable DSCP ingress classification. Disabled - Disable DSCP ingress classification. |
| tnQosExtDscpIfClassifExtMapTable | 1.3.6.1.4.1.868.2.5.9.1.3.7 | not-accessible | A table config the Dscp ingress classification mapping. | |
| tnQosExtDscpIfClassifExtMapEntry | 1.3.6.1.4.1.868.2.5.9.1.3.7.1 | not-accessible | An entry in this table perform the Dscp ingress classification mapping. | |
| INT tnQosExtDscpIfClassifExtMapClass | 1.3.6.1.4.1.868.2.5.9.1.3.7.1.1 | INTEGER | not-accessible | The Traffic Class the received frame is mapped to. tnQosExtDscpIfClassifExtMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)). |
| INT tnQosExtDscpIfClassifExtMapDpl | 1.3.6.1.4.1.868.2.5.9.1.3.7.1.2 | INTEGER | not-accessible | The DP (Drop Precedence) level the received frame is mapped to. |
| INT tnQosExtDscpIfClassifExtMapDscp | 1.3.6.1.4.1.868.2.5.9.1.3.7.1.3 | INTEGER | read-write | The Classified DSCP from QoS class and DP level. The DSCP which needs to be classified depends on interface DSCP classification and DSCP classification mode. Incoming frame DSCP may be translated before using the value for classification. |
| tnQosExtDscpIfEgressRemarkTable | 1.3.6.1.4.1.868.2.5.9.1.3.8 | not-accessible | A table represents the DSCP egress remark mode on an interface. | |
| tnQosExtDscpIfEgressRemarkEntry | 1.3.6.1.4.1.868.2.5.9.1.3.8.1 | not-accessible | An entry in the table represents the DSCP egress remark mode on an interface. | |
| INT tnQosExtDscpIfEgressRemarkMode | 1.3.6.1.4.1.868.2.5.9.1.3.8.1.1 | INTEGER | read-write | Controls the egress frame DSCP field rewrite setting per port. Disable: No Egress rewrite. Enable: Rewrite enable without remapped. Remap DP Unaware: DSCP from analyzer is remapped and frame is remarked with remapped DSCP value. Remap DP Aware: DSCP from analyzer is remapped and frame is remarked with remapped DSCP value. |
| tnQosExtDscpIfEgressRemarkMapTable | 1.3.6.1.4.1.868.2.5.9.1.3.9 | not-accessible | A table represents the DSCP egress remark map on an interface. | |
| tnQosExtDscpIfEgressRemarkMapEntry | 1.3.6.1.4.1.868.2.5.9.1.3.9.1 | not-accessible | An entry in the table represents the DSCP egress remark map on an interface. | |
| INT tnQosExtDscpIfEgressRemarkMapDscp | 1.3.6.1.4.1.868.2.5.9.1.3.9.1.1 | INTEGER | not-accessible | The classified DSCP value of the specific IP frame, used for DSCP egress remark. DSCP valid range is 0 - 63 |
| INT tnQosExtDscpIfEgressRemarkMapDpl | 1.3.6.1.4.1.868.2.5.9.1.3.9.1.2 | INTEGER | not-accessible | The classified DP (Drop Precedence) level of the specific frame, used for DSCP egress remark. |
| INT tnQosExtDscpIfEgressRemarkMapToDscp | 1.3.6.1.4.1.868.2.5.9.1.3.9.1.3 | INTEGER | read-write | The DSCP value to which you want to remap for the egress side. This remap is based on classified DSCP and DP level. |
| tnQosExtQclMgmt | 1.3.6.1.4.1.868.2.5.9.1.4 | |||
| tnQosExtQclTable | 1.3.6.1.4.1.868.2.5.9.1.4.1 | not-accessible | A table used to configure the QoS Control List settings. | |
| tnQosExtQclEntry | 1.3.6.1.4.1.868.2.5.9.1.4.1.1 | not-accessible | An entry in the table used to configure the QoS Control List settings. | |
| INT tnQosExtQclIndex | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.1 | INTEGER | not-accessible | The row index of the QCL. |
| INT tnQosExtQclId | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.2 | INTEGER | read-only | The identifier of the QCL. |
| INT tnQosExtQclNextQclId | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.3 | INTEGER | read-create | Specify the created ECE is placed before which QCL. |
| POR tnQosExtQclPortList | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.4 | PortList | read-create | The list of port members for the QCL. |
| INT tnQosExtQclTagType | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.5 | INTEGER | read-create | The frame tag type for matching the QCL. The possible values are: tagged: The QCL will match tagged frames only. untagged: The QCL will match untagged frames only. any: The QCL will match both tagged and untagged frames. |
| INT tnQosExtQclTagVlanType | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.6 | INTEGER | read-create | The VLAN ID filter type for matching the QCL. It is only significant if tnQosExtQclTagType is 'tagged' or 'any'. The possible values are: any: No VLAN ID filter is specified. (VLAN ID filter status is 'don't-care'.) specific: If you want to filter a specific VLAN ID value with this QCL, choose this value. A field for entering a specific value appears. range: If you want to filter a specific VLAN ID range filter with this QCL, choose this value. A field for entering a range appears. |
| VLA tnQosExtQclTagVlanVal | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.7 | VlanIndex | read-create | The Specific VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType is selected 'specific'. |
| VLA tnQosExtQclTagVlanMin | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.8 | VlanIndex | read-create | The Start of Range VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType is selected 'range'. this value should be lower than tnQosExtQclTagVlanMax value. |
| VLA tnQosExtQclTagVlanMax | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.9 | VlanIndex | read-create | The End of Range VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType is selected 'range'. this value should be higher than tnQosExtQclTagVlanMin value. |
| BIT tnQosExtQclTagPcp | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.10 | Bits | read-create | The PCP value for mataching the QCL. It is only significant if tnQosExtQclTagType is 'tagged' or 'any'. The possible values are: any: The QCL will match any PCP value(all bits will be set to 1). specific: each bit matchs a specific PCP of QCL(from bit0 to bit7). range: The QCL will match PCP values in the selected range, valid range is depend on the specific implement. e.g: for S3280, the valid range are bit0-bit1, bit2-bit3, bit4-bit5, bit6-bit7, bit0-bit3 or bit4-bit7. |
| INT tnQosExtQclTagDei | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.11 | INTEGER | read-create | The DEI value for mataching the QCL. It is only significant if tnQosExtQclTagType is 'tagged' or 'any'. The possible values are: 'any', 'dei0' or 'dei1'. |
| INT tnQosExtQclSMacType | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.12 | INTEGER | read-create | The source MAC address filter type for matching the QCL. The possible values are: any: No source MAC address filter is specified. (source MAC address filter status is 'don't-care'.) specific: choose this value to filter a specific source MAC address value with this QCL. |
| MAC tnQosExtQclSMac | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.13 | MacAddress | read-create | The source MAC address filter for matching the QCL. In S3280 implement, only MAC OUI(first three octets) are used for MAC address matching process. |
| INT tnQosExtQclDMacType | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.14 | INTEGER | read-create | The destination MAC address filter for matching the QCL. The possible values are: any: No destination MAC address filter is specified. (destination MAC address filter status is 'don't-care'.) unicast: Match the unicast destination MAC address for the QCL. multicast: Match the multicast destination MAC address for the QCL. broadcast: Match the broadcast destination MAC address for the QCL. |
| INT tnQosExtQclFrameType | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.15 | INTEGER | read-create | The frame type for the QCL. The possible values are: any: The QCL will match any frame type. ethernet: The QCL will match Ethernet frame type. llc: The QCL will match LLC frame type. snap: The QCL will match SNAP frame type. ipv4: The QCL will match IPv4 frames. ipv6: The QCL will match IPv6 frames. |
| INT tnQosExtQclActClassDefault | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.16 | INTEGER | read-create | Determe the type of matched frame traffic class modification. default: QCL do not change the traffic class of the matched received frames. specific: QCL will change the traffic class to the specific value of the matched received frames. |
| INT tnQosExtQclActClass | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.17 | INTEGER | read-create | If a frame matches the QCE it will be put in the queue. It is only significant if tnQosExtQclActClassDefault is selected 'specific' value. tnQosExtQclActClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)). |
| INT tnQosExtQclActDplDefault | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.18 | INTEGER | read-create | Determe the type of matched frame traffic DP (Drop Precedence) level modification. default: QCL do not change the DP (Drop Precedence) level of the matched received frames. specific: QCL will change the DP (Drop Precedence) level to the specific value of the matched received frames. |
| INT tnQosExtQclActDpl | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.19 | INTEGER | read-create | If a frame matches the QCE then DP level will set to the value. It is only significant if tnQosExtQclActDplDefault is selected 'specific' value. |
| INT tnQosExtQclActDscpDefault | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.20 | INTEGER | read-create | Determe the type of matched frame DSCP modification. default: QCL do not change the DSCP of the matched received frames. specific: QCL will change the DSCP to the specific value of the matched received frames. |
| INT tnQosExtQclActDscp | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.21 | INTEGER | read-create | If a frame matches the QCE then DSCP will be classified with the value. It is only significant if tnQosExtQclActDscpDefault is selected 'specific' value. |
| INT tnQosExtQclConflict | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.22 | INTEGER | read-only | QCE status. It may be that resources required to add a QCE may not be available; in that case it shows conflict status as 'yes', otherwise it is always 'no'. |
| ROW tnQosExtQclStatus | 1.3.6.1.4.1.868.2.5.9.1.4.1.1.23 | RowStatus | read-create | The status of this conceptual row entry of QCL table. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. For a detailed description of this object, please refer to SNMPv2-TC MIB. |
| tnQosExtQclL2Table | 1.3.6.1.4.1.868.2.5.9.1.4.2 | not-accessible | A table used to configure the QoS Control List layer 2 frame settings. | |
| tnQosExtQclL2Entry | 1.3.6.1.4.1.868.2.5.9.1.4.2.1 | not-accessible | An entry in the table used to configure the QoS Control List layer 2 fram settings. | |
| INT tnQosExtQclEtherType | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.1 | INTEGER | read-write | The Ether type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'ethernet' is selected. The possible values are: any: No Ether type filter is specified. (Ether type filter status is 'don't-care'.) specific: Choose this value to filter a specific Ether type value with this QCL. |
| INT tnQosExtQclEtherVal | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.2 | INTEGER | read-write | When tnQosExtQclEtherType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0x0600 through 0xFFFF. If implement supports ipv4 or ipv6 selection in tnQosExtQclFrameType, the value 0x0800(ipv4) or 0x86DD(ipv6) are reserved from setting. |
| INT tnQosExtQclLlcSsapType | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.3 | INTEGER | read-write | The LLC SSAP type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'llc' is selected. The possible values are: any: No SSAP type filter is specified. (SSAP type filter status is 'don't-care'.) specific: Choose this value to filter a specific SSAP type value with this QCL. |
| INT tnQosExtQclLlcSsapVal | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.4 | INTEGER | read-write | When tnQosExtQclLlcSsapType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 255. |
| INT tnQosExtQclLlcDsapType | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.5 | INTEGER | read-write | The LLC DSAP type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'llc' is selected. The possible values are: any: No DSAP type filter is specified. (DSAP type filter status is 'don't-care'.) specific: Choose this value to filter a specific DSAP type value with this QCL. |
| INT tnQosExtQclLlcDsapVal | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.6 | INTEGER | read-write | When tnQosExtQclLlcDsapType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 255. |
| INT tnQosExtQclLlcControlType | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.7 | INTEGER | read-write | The LLC Control type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'llc' is selected. The possible values are: any: No Control type filter is specified. (Control type filter status is 'don't-care'.) specific: Choose this value to filter a specific Control type value with this QCL. |
| INT tnQosExtQclLlcControlVal | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.8 | INTEGER | read-write | When tnQosExtQclLlcControlType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 255. |
| INT tnQosExtQclSnapPidType | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.9 | INTEGER | read-write | The SNAP PID type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'snap' is selected. The possible values are: any: No SNAP PIDtype filter is specified. (SNAP PID type filter status is 'don't-care'.) specific: Choose this value to filter a specific SNAP PID type value with this QCL. |
| INT tnQosExtQclSnapPidVal | 1.3.6.1.4.1.868.2.5.9.1.4.2.1.10 | INTEGER | read-write | When tnQosExtQclSnapPidType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0x600 through 0xFFFF. If implement supports ipv4 or ipv6 selection in tnQosExtQclFrameType, the value 0x0800(ipv4) or 0x86DD(ipv6) are reserved from setting. |
| tnQosExtQclIpTable | 1.3.6.1.4.1.868.2.5.9.1.4.3 | not-accessible | A table used to configure the QoS Control List IP settings. | |
| tnQosExtQclIpEntry | 1.3.6.1.4.1.868.2.5.9.1.4.3.1 | not-accessible | An entry in the table used to configure the QoS Control List IP settings. | |
| INT tnQosExtQclProtoType | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.1 | INTEGER | read-write | The IP protocol for matching the QCL.The possible values are: any: No protocol filter is specified. (Protocol filter status is 'don't-care'.) udp: Specify the UDP for matching the QCL. tcp: Specify the TCP for matching the QCL. specific: Choose this value to filter a specific protocol value with this QCL. |
| INT tnQosExtQclProtoVal | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.2 | INTEGER | read-write | When tnQosExtQclProtoType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 255. If implement supports udp or tcp selection in tnQosExtQclProtoType, the value 6(tcp) or 17(udp) are reserved from setting. |
| INT tnQosExtQclDscpType | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.3 | INTEGER | read-write | The DSCP filter for matching the QCL. The possible values are: any: No DSCP filter is specified. (DSCP filter status is 'don't-care'.) specific: choose this value to filter a specific DSCP value with this QCL. range: Choose this value to filter a specific DSCP range filter with this QCL. |
| INT tnQosExtQclDscpVal | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.4 | INTEGER | read-write | When tnQosExtQclDscpType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 63. |
| INT tnQosExtQclDscpMin | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.5 | INTEGER | read-write | When tnQosExtQclDscpType is selected 'Range' value, you can enter a specific range. this value should be lower than tnQosExtQclDscpMax value. The allowed range start is from 0 through 63. |
| INT tnQosExtQclDscpMax | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.6 | INTEGER | read-write | When tnQosExtQclDscpType is selected 'Range' value, you can enter a specific range. this value should be higher than tnQosExtQclDscpMin value. The allowed range end is from 0 through 63. |
| INT tnQosExtQclSrcIpType | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.7 | INTEGER | read-write | The source IP address type filter for matching the QCL. The possible values are: any: No source IP address filter is specified. (source IP address filter status is 'don't-care'.) specific: Choose this value to filter a specific source IP address with this QCL. |
| IPt tnQosExtQclSrcIpAddrType | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.8 | InetAddressType | read-write | Specify the tnQosExtQclSrcIpAddr type. |
| IP tnQosExtQclSrcIpAddr | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.9 | InetAddress | read-write | When tnQosExtQclSrcIpType is selected 'Specific' value, you can enter a specific host or network address. |
| IPt tnQosExtQclSrcIpMaskType | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.10 | InetAddressType | read-write | Specify the tnQosExtQclSrcIpMask type. |
| IP tnQosExtQclSrcIpMask | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.11 | InetAddress | read-write | When tnQosExtQclSrcIpType is selected 'Specific' value, you can enter a specific network mask for the source IP address. |
| INT tnQosExtQclIpv4Fragment | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.12 | INTEGER | read-write | The IPv4 Fragment for matching the QCL. This involves the settings for the More Fragments (MF) bit and the Fragment Offset (FRAG OFFSET) field for an IPv4 frame. The possible values are: any: The QCL will match any MF bit. fragment: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must be able to match this entry. nonfragment: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must not be able to match this entry. |
| INT tnQosExtQclTcpUdpSportType | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.13 | INTEGER | read-write | The TCP/UDP source port for matching the QCL. It is only significant if protocol filter 'UDP' or 'TCP' is selected. The possible values are: any: No TCP/UDP source port filter is specified. (Source port filter status is 'don't-care'.) specific: Choose this value to filter a specific TCP/UDP source port No. with this QCL. range: Choose this value to filter a specific TCP/UDP source port range filter with this QCL. |
| INT tnQosExtQclTcpUdpSportVal | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.14 | INTEGER | read-write | When tnQosExtQclTcpUdpSportType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 65535. |
| INT tnQosExtQclTcpUdpSportMin | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.15 | INTEGER | read-write | When tnQosExtQclTcpUdpSportType is selected 'Range' value, you can enter a specific range. this value should be lower than tnQosExtQclTcpUdpSportMax value. The allowed range start is from 0 through 65535. |
| INT tnQosExtQclTcpUdpSportMax | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.16 | INTEGER | read-write | When tnQosExtQclTcpUdpSportType is selected 'Range' value, you can enter a specific range. this value should be higher than tnQosExtQclTcpUdpSportMin value. The allowed range end is from 0 through 65535. |
| INT tnQosExtQclTcpUdpDportType | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.17 | INTEGER | read-write | The TCP/UDP destination port for matching the QCL. It only significant if protocol filter 'UDP' or 'TCP' is selected. The possible values are: any: No TCP/UDP destination port filter is specified. (Source port filter status is 'don't-care'.) specific: Choose this value to filter a specific TCP/UDP source port No. with this QCL. range: Choose this value to filter a specific TCP/UDP source port range filter with this QCL. |
| INT tnQosExtQclTcpUdpDportVal | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.18 | INTEGER | read-write | When tnQosExtQclTcpUdpDportVal is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 65535. |
| INT tnQosExtQclTcpUdpDportMin | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.19 | INTEGER | read-write | When tnQosExtQclTcpUdpDportVal is selected 'Range' value, you can enter a specific range. this value should be lower than tnQosExtQclTcpUdpDportMax value. The allowed range start is from 0 through 65535. |
| INT tnQosExtQclTcpUdpDportMax | 1.3.6.1.4.1.868.2.5.9.1.4.3.1.20 | INTEGER | read-write | When tnQosExtQclTcpUdpDportVal is selected 'Range' value, you can enter a specific range. this value should be higher than tnQosExtQclTcpUdpDportMin value. The allowed range end is from 0 through 65535. |
RFC description
Vendor-private MIB (likely Nortel/Ciena) extending QoS management capabilities for network devices.
Start monitoring Transition Networks managed switch (per-port/per-queue policer config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.