All MIBs › TN-EVC-MIB
Organization: Transition Networks, Inc.
Last Updated: 2014-05-06
Category: Service Management, Transition Networks Media Converters
Description: Manages Transition Networks Ethernet virtual circuit provisioning, attributes, and status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TN-EVC-MIB?
TN-EVC-MIB is a Transition Networks private MIB for managing Ethernet Virtual Circuits (EVCs) on the vendor's managed media-converter and switching platforms. It exposes port-level EVC attributes such as tag mode, DEI mode, and address learning, together with EVC-level attributes like VLAN ID (VID), inner VID, and NNI port list, covering both configuration and operational status of provisioned virtual circuits. From a monitoring standpoint it is used to confirm that Carrier Ethernet services are provisioned and operating as expected -- e.g., that the correct VLANs are mapped to the correct NNI ports and that learning/tagging behavior matches the service design -- functioning as a service/software-status MIB rather than exposing hardware environmentals. It builds on IEEE 802.1ad/MEF Ethernet virtual circuit concepts layered onto Transition Networks' device architecture. It is typically deployed in carrier Ethernet access/aggregation networks where Transition Networks media converters or switches terminate EVCs for business services. Network engineers evaluating or troubleshooting this functionality can download the TN-EVC-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TN-EVC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Transition Networks managed media converters/switches
Monitoring Examples
An operator can poll tnEvcTable/tnEvcEntry using tnEvcIndex to check tnEvcVid and tnEvcIVid against the expected service VLAN mapping, and inspect tnEvcNNIPortlist to confirm the EVC is bound to the correct network-facing ports. Checking tnEvcPortTable's tnEvcPortTagMode and tnEvcPortDEIMode per port can reveal a misconfigured tagging mode that would cause a customer's traffic to be dropped or misclassified.
What Can Be Monitored
- EVC VLAN ID / inner VID mapping
- NNI port list per EVC
- port tag mode
- DEI mode
- address learning mode
This MIB depends on
Related MIBs
Imported Objects
From ENTITY-MIB
| entPhysicalIndex | OBJECT-TYPE |
From IF-MIB
| InterfaceIndexOrZero | |
| ifIndex | OBJECT-TYPE |
From INET-ADDRESS-MIB
| InetAddress |
From Q-BRIDGE-MIB
| PortList | |
| VlanId | |
| VlanIdOrAny | |
| VlanIdOrAnyOrNone | |
| VlanIdOrNone |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter64 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| RowStatus | |
| StorageType | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From TRANSITION-SMI
| tnProducts | OBJECT-IDENTITY |
How to Use in IPNetwork Monitor
Example using tnEvcStatGreenFrameRx OID:
Select a Transition Networks managed media converters/switch (Ethernet Virtual Circuit VLAN/tagging config status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tnEvcStatGreenFrameRx into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of green received. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| INT tnEvcBandwidthProfilesCBS | 1.3.6.1.4.1.868.2.5.106.1.1.4.1.4 | INTEGER | read-create | The Committed Burst Size of the bandwidth profile. The allowed range is from 0 through 100,000 bytes. |
| INT tnEvcBandwidthProfilesCIR | 1.3.6.1.4.1.868.2.5.106.1.1.4.1.3 | INTEGER | read-create | The Committed Information Rate of the bandwidth profile. The allowed range is from 0 through 10,000,000 kilobit per second. |
| INT tnEvcBandwidthProfilesEBS | 1.3.6.1.4.1.868.2.5.106.1.1.4.1.6 | INTEGER | read-create | The Excess Burst Size of the bandwidth profile. The allowed range is from 0 through 100,000 bytes. |
| INT tnEvcBandwidthProfilesEIR | 1.3.6.1.4.1.868.2.5.106.1.1.4.1.5 | INTEGER | read-create | The Excess Information Rate of the bandwidth profile. The allowed range is from 0 through 10,000,000 kilobit per second. |
| tnEvcBandwidthProfilesEntry | 1.3.6.1.4.1.868.2.5.106.1.1.4.1 | not-accessible | This entry represents an entry of EVC ingress bandwidth profile configuration. | |
| INT tnEvcBandwidthProfilesIndex | 1.3.6.1.4.1.868.2.5.106.1.1.4.1.1 | INTEGER | not-accessible | The EVC bandwidth profiles policer index. |
| INT tnEvcBandwidthProfilesPolicerMode | 1.3.6.1.4.1.868.2.5.106.1.1.4.1.2 | INTEGER | read-create | The colour mode of the bandwidth profile. The allowed values are: coupled: Colour-aware mode with coupling enabled. aware: Colour-aware mode with coupling disabled. |
| INT tnEvcBandwidthProfilesState | 1.3.6.1.4.1.868.2.5.106.1.1.4.1.7 | INTEGER | read-create | The administrative state of the bandwidth profile. The allowed values are: enabled: The bandwidth profile enabled. disabled: The bandwidth profile is disabled. |
| tnEvcBandwidthProfilesTable | 1.3.6.1.4.1.868.2.5.106.1.1.4 | not-accessible | This entry displays and sets current EVC ingress bandwidth profile configurations. These policers may be used to limit the traffic received on UNI ports. | |
| tnEvcCfgMgmtGroup | 1.3.6.1.4.1.868.2.5.106.1.1 | |||
| tnEvcConformance | 1.3.6.1.4.1.868.2.5.106.1.8 | |||
| INT tnEvcEceActClass | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.42 | INTEGER | read-create | The traffic class for the ECE. The allowed range is from 0 through 8 or disabled. |
| INT tnEvcEceActDirection | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.37 | INTEGER | read-create | The EVCs and ECEs are used to setup flows in one or both directions as determined by the ECE Direction parameter. If the ECE is bidirectional, the ingress rules of the NNI ports will be setup to match the traffic being forwarded to NNI ports. The possible values are: both: Bidirectional. uni2nni: Unidirectional from UNI to NNI. nni2uni: Unidirectional from NNI to UNI. |
| INT tnEvcEceActDropPrecType | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.20 | INTEGER | read-write | The drop precedence for the ECE. The allowed range is 0, 1 or disabled. |
| INT tnEvcEceActEvcidFilterType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.38 | INTEGER | read-create | The outer tag PCP and DEI preservation for the ECE. The possible values are: any: No EVC ID filter is specified. (EVC ID filter status is 'don't-care'.) specific: If you want to filter a specific EVC ID with this ECE, choose this value. A field for entering a specific value appears. |
| INT tnEvcEceActEvcidVal | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.39 | INTEGER | read-create | When 'Specific' is selected for the VLAN ID filter, you can enter a specific value. The allowed value is from 1 through 128. |
| INT tnEvcEceActPolicyId | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.41 | INTEGER | read-create | The ACL Policy ID for the ECE for matching ACL rules. The allowed range is from 0 through 255. |
| INT tnEvcEceActRuleType | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.18 | INTEGER | read-write | The rule type for the ECE. The possible values are: Both: Ingress and egress rule. RX: Ingress rule. TX: Egress rule. |
| INT tnEvcEceActTagPopCount | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.40 | INTEGER | read-create | The ingress tag pop count for the ECE. The allowed range is from 0 through 2. |
| INT tnEvcEceActTxLookupType | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.19 | INTEGER | read-write | The TX lookup for the ECE. The possible values are: VID lookup: The TX lookup is based on VID. VID-PCP: The TX lookup is based on VID and PCP. ISDX: The TX lookup is based on ISDX. |
| INT tnEvcEceConflict | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.46 | INTEGER | read-only | Indicates the hardware status of the specific ECE. The specific ECE is not applied to the hardware due to hardware limitations. |
| INT tnEvcEceDMacSMacFilterType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.43 | INTEGER | read-create | The source/destination MAC address for matching the ECE. It depend on by the port address mode, when port address mode is set to 'Source' then the field is used for source MAC address. Similarly when port address mode is set to 'Destination' then the field is used for destination MAC address. The possible values are: any: No SMAC/DMAC filter is specified. (SMAC/DMAC filter status is 'don't-care'.) specific: If you want to filter a specific SMAC/DMAC value with this ECE, choose this value. A field for entering a specific value appears. |
| MAC tnEvcEceDMacSMacVal | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.44 | MacAddress | read-create | When 'Specific' is selected for the SMAC/DMAC filter, you can enter a specific value. The legal format is 'xx-xx-xx-xx-xx-xx' or 'xx.xx.xx.xx.xx.xx' or 'xxxxxxxxxxxx' (x is a hexadecimal digit). |
| INT tnEvcEceDMacType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.45 | INTEGER | read-create | The destination MAC address for matching the ECE. The possible values are: any: No destination MAC address is specified. unicast: Frame must be unicast. multicast: Frame must be multicast. broadcast: Frame must be broadcast. specific: If you want to filter a specific DMAC value with this ECE, choose this value. |
| MAC tnEvcEceDMacVal | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.15 | MacAddress | read-write | When 'Specific' is selected for the DMAC filter, you can enter a specific value. The legal format is 'xx-xx-xx-xx-xx-xx' or 'xx.xx.xx.xx.xx.xx' or 'xxxxxxxxxxxx' (x is a hexadecimal digit). |
| INT tnEvcEceDscpFilterType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.14 | INTEGER | read-create | The DSCP filter for matching the ECE. The possible values are: any: No DSCP filter is specified. (DSCP filter status is 'don't-care'.) specific: If you want to filter a specific DSCP value with this ECE, choose this value. A field for entering a specific value appears. range: If you want to filter a specific DSCP range filter with this ECE, choose this value. A field for entering a range appears. |
| INT tnEvcEceDscpFilterVal | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.15 | INTEGER | read-create | When 'Specific' is selected for the DSCP filter, you can enter a specific value. The allowed value is from 0 through 63. |
| INT tnEvcEceDscpRangeEnd | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.17 | INTEGER | read-create | When 'Range' is selected for the DSCP filter, you can enter a specific range. The allowed range end is from 0 through 63. |
| INT tnEvcEceDscpRangeStart | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.16 | INTEGER | read-create | When 'Range' is selected for the DSCP filter, you can enter a specific range. The allowed range start is from 0 through 63. |
| INT tnEvcEceDstPortFilterNo | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.23 | INTEGER | read-create | When 'Specific' is selected for the destination port filter, you can enter a specific value. The allowed value is from 0 through 65535. |
| INT tnEvcEceDstPortFilterType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.22 | INTEGER | read-create | The TCP/UDP destination port for matching the ECE. It only significant if protocol filter 'UDP' or 'TCP' is selected. The possible values are: any: No TCP/UDP destination port filter is specified. (Source port filter status is 'don't-care'.) specific: If you want to filter a specific TCP/UDP source port No. with this ECE, choose this value. A field for entering a specific No. appears. range: If you want to filter a specific TCP/UDP source port range filter with this ECE, choose this value. A field for entering a range appears. |
| INT tnEvcEceDstPortRangeEnd | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.25 | INTEGER | read-create | When 'Range' is selected for the destination port filter, you can enter a specific range. The allowed range end is from 0 through 65535. |
| INT tnEvcEceDstPortRangeStart | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.24 | INTEGER | read-create | When 'Range' is selected for the destination port filter, you can enter a specific range. The allowed range start is from 0 through 65535. |
| tnEvcEceEntry | 1.3.6.1.4.1.868.2.5.106.1.1.3.1 | not-accessible | This entry represents an ECE. The system automatically creates an entry when the system or the EMS/NMS creates a row in the cevcECETable. Likewise, the system automatically destroys an entry when the system or the EMS/NMS destroys the corresponding row in the cevcECETable. | |
| U32 tnEvcEceEtypeData | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.33 | Unsigned32 | read-write | When 'Specific' is selected for the Ethernet type filter, you can enter a specific value. The allowed value is from 0x600 through 0xFFFF but exclude 0x0800(IPv4), 0x806(ARP) and 0x86DD(IPv6). |
| INT tnEvcEceEtypeDataFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.32 | INTEGER | read-write | The Ethernet type data for matching the ECE. The possible values are: Any: No Ethernet type data filter is specified. (Ethernet type filter status is 'don't-care'.) Specific: If you want to filter a specific Ethernet type value with this ECE, choose this value. |
| U32 tnEvcEceEtypeDataMask | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.34 | Unsigned32 | read-write | When 'Specific' is selected for the Ethernet type data filter, you can enter a specific value. It is a pair of the Ethernet type data and its mask. The allowed value is from 0x0 through 0xFFFF. |
| INT tnEvcEceEtypeFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.30 | INTEGER | read-write | The Ethernet type value for matching the ECE. The possible values are: Any: No Ethernet type value filter is specified. (Ethernet type filter status is 'don't-care'.) Specific: If you want to filter a specific Ethernet type value with this ECE, choose this value. |
| U32 tnEvcEceEtypeValue | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.31 | Unsigned32 | read-write | When 'Specific' is selected for the Ethernet type filter, you can enter a specific value. The allowed value is from 0x600 through 0xFFFF but exclude 0x0800(IPv4), 0x806(ARP) and 0x86DD(IPv6). |
| INT tnEvcEceId | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.1 | INTEGER | not-accessible | The identifier of the ECE. |
| INT tnEvcEceIInnerDeiMode | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.22 | INTEGER | read-write | The inner tag DEI mode for the ECE. The possible values are: Classified: The inner tag DEI mode is classified. Fixed: The inner tag DEI mode is fixed. Drop Precedence: The inner tag DEI mode is drop precedence. |
| INT tnEvcEceInnerDEI | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.14 | INTEGER | read-create | The inner tag DEI value for the ECE. The allowed value is 0 or 1. |
| INT tnEvcEceInnerPCP | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.13 | INTEGER | read-create | The inner tag PCP value for the ECE. The allowed range is from 0 through 7. |
| INT tnEvcEceInnerPCPDEIPreserve | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.12 | INTEGER | read-create | The inner tag PCP and DEI preservation for the ECE. The possible values are: Preserved: The inner tag PCP and DEI is preserved. Fixed: The inner tag PCP and DEI is fixed. |
| INT tnEvcEceInnerPcpMode | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.21 | INTEGER | read-write | The inner tag PCP mode for the ECE. The possible values are: Classified: The inner tag PCP Mode is classified. Fixed: The inner tag PCP Mode is classified. Mapped: The inner tag PCP Mode is based on mapped (QOS, DP). |
| INT tnEvcEceInnerTagDEI | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.7 | INTEGER | read-create | The DEI value for matching the ECE. It only significant if tag type 'Tagged' is selected. The allowed value is: 0, 1 or Any. |
| BIT tnEvcEceInnerTagPCP | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.6 | Bits | read-create | The PCP value for matching the ECE. It only significant if tag type 'Tagged' is selected. The possible values are: any: The ECE will match any PCP value(all bits will be set to 1). specific: each bit matchs a specific PCP of ECE(from bit0 to bit7). range: The ECE will match PCP values in the selected range, valid range bit0-bit1, bit2-bit3, bit4-bit5, bit6-bit7, bit0-bit3 or bit4-bit7. |
| INT tnEvcEceInnerTagType | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.1 | INTEGER | read-create | The Inner tag type for the ECE. The possible values are: tagged: The ECE will match tagged frames only. untagged: The ECE will match untagged frames only. any: The ECE will match both tagged and untagged frames. If supported: C-Tagged: The ECE will match custom tagged frames only. S-Tagged: The ECE will match service tagged frames only. |
| VLA tnEvcEceInnerTagVIDFilterEnd | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.5 | VlanIdOrNone | read-create | When 'Range' is selected for the Inner VLAN ID filter, you can enter a specific range. The allowed range end is from 0 through 4094. |
| VLA tnEvcEceInnerTagVIDFilterStart | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.4 | VlanIdOrNone | read-create | When 'Range' is selected for the Inner VLAN ID filter, you can enter a specific range. The allowed range start is from 0 through 4094. |
| INT tnEvcEceInnerTagVIDFilterType | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.2 | INTEGER | read-create | The Inner VLAN ID filter for matching the ECE. It only significant if tag type 'Tagged' is selected. The possible values are: any: No VLAN ID filter is specified. (VLAN ID filter status is 'don't-care'.) specific: If you want to filter a specific VLAN ID value with this ECE, choose this value. A field for entering a specific value appears. range: If you want to filter a specific VLAN ID range filter with this ECE, choose this value. A field for entering a range appears. |
| VLA tnEvcEceInnerTagVIDFilterVal | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.3 | VlanIdOrNone | read-create | When 'Specific' is selected for the Inner VLAN ID filter, you can enter a specific value. The allowed value is from 0 through 4094. |
| VLA tnEvcEceInnerVid | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.11 | VlanIdOrNone | read-create | The inner tag VLAN ID for the ECE. The allowed range is from 0 through 4094. |
| IP tnEvcEceIpv4DipAddr | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.24 | InetAddress | read-write | When 'Host' or 'Network' is selected for the DIP filter, you can enter a specific host or network address. |
| INT tnEvcEceIpv4DipFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.23 | INTEGER | read-write | The destination IP address for matching the ECE. The possible values are: Any: No DIP filter is specified. (DIP filter status is 'don't-care'.) Host: If you want to filter a specific host address with this ECE, choose this value. A field for entering a host address appears. Network: If you want to filter a specific network address with this ECE, choose this value. A Two fields for entering a specific network address and network mask appears. |
| IP tnEvcEceIpv4DipMask | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.25 | InetAddress | read-write | When 'Host' or 'Network' is selected for the DIP filter, you can enter a specific network mask. |
| IP tnEvcEceIpv4DipSipAddr | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.27 | InetAddress | read-create | When 'Host' or 'Network' is selected for the SIP/DIP filter, you can enter a specific host or network address. |
| INT tnEvcEceIpv4DipSipFilter | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.26 | INTEGER | read-create | The source/destination IP address for matching the ECE. It depend on by the port address mode, when port address mode is set to 'Source' then the field is used for source address. Similarly when port address mode is set to 'Destination' then the field is used for destination address. The possible values are: Any: No SIP/DIP filter is specified. (SIP/DIP filter status is 'don't-care'.) Host: If you want to filter a specific host address with this ECE, choose this value. A field for entering a host address appears. Network: If you want to filter a specific network address with this ECE, choose this value. A Two fields for entering a specific network address and network mask appears. |
| IP tnEvcEceIpv4DipSipMask | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.28 | InetAddress | read-create | When 'Host' or 'Network' is selected for the SIP/DIP filter, you can enter a specific network mask. |
| INT tnEvcEceIpv4Fragment | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.29 | INTEGER | read-create | The IPv4 Fragment for matching the ECE. This involves the settings for the More Fragments (MF) bit and the Fragment Offset (FRAG OFFSET) field for an IPv4 frame. The possible values are: any: The ECE will match any MF bit. fragment: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must be able to match this entry. nonfragment: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must not be able to match this entry. |
| U32 tnEvcEceIpv6DipAddr | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.27 | Unsigned32 | read-write | When 'Host' or 'Network' is selected for the DIP filter, you can enter a specific host or network address. |
| INT tnEvcEceIpv6DipFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.26 | INTEGER | read-write | The destination IP address for matching the ECE. The possible values are: Any: No DIP filter is specified. (DIP filter status is 'don't-care'.) Host: If you want to filter a specific host address with this ECE, choose this value. A field for entering a host address appears. Network: If you want to filter a specific network address with this ECE, choose this value. A Two fields for entering a specific network address and network mask appears. |
| U32 tnEvcEceIpv6DipMask | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.28 | Unsigned32 | read-write | When 'Host' or 'Network' is selected for the DIP filter, you can enter a specific network mask. |
| U32 tnEvcEceIpv6DipSipAddr | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.31 | Unsigned32 | read-create | When 'Host' or 'Network' is selected for the SIP/DIP filter, you can enter a specific host or network address. When 'IPv6' is selected for the Frame Type, the field only supported 32 bits for IPv6 address. |
| INT tnEvcEceIpv6DipSipFilter | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.30 | INTEGER | read-create | The source/destination IP address for matching the ECE. It depend on by the port address mode, when port address mode is set to 'Source' then the field is used for source address. Similarly when port address mode is set to 'Destination' then the field is used for destination address. The possible values are: Any: No SIP/DIP filter is specified. (SIP/DIP filter status is 'don't-care'.) specific: If you want to filter a specific host address with this ECE, choose this value. A field for entering a host address appears. |
| U32 tnEvcEceIpv6DipSipMask | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.32 | Unsigned32 | read-create | When 'Host' or 'Network' is selected for the SIP/DIP filter, you can enter a specific network mask. When 'IPv6' is selected for the Frame Type, the field only supported 32 bits for IPv6 address mask. |
| INT tnEvcEceL2cpProtoType | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.48 | INTEGER | read-write | The L2CP type for the ECE. The possible values are: STP/RSTP/MSTP: Match STP/RSTP/MSTP frames. Pause: Match Pause frames. LACP: Match LACP frames. LAMP: Match LAMP frames. Link OAM(802.1ah): Match Link OAM(802.1ah) frames. Port Authentication(802.1x): Match Port Authentication(802.1x) frames. E-LMI: Match PB Group Address frames. PB Group Address: Match PB Group Address frames. PB GVRP: Match PB GVRP frames. LLDP: Match LLDP frames. GMRP: Match GMRP frames. GVRP: Match GVRP frames. ULD: Match ULD frames. PAgP: Match PAgP frames. PVST/PVST+: Match PVST/PVST+ frames. Cisco BPDU: Match Cisco BPDU frames. CDP: Match CDP frames. VTP: Match VTP frames. DTP: Match DTP frames. STP Uplink Fast: Match STP Uplink Fast frames. Cisco CFM: Match Cisco CFM frames. |
| INT tnEvcEceLlcCtrlFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.39 | INTEGER | read-write | The LLC control for matching the ECE. The possible values are: Any: No LLC control value filter is specified. (LLC control filter status is 'don't-care'.) Specific: If you want to filter a specific LLC control value with this ECE, choose this value. |
| U32 tnEvcEceLlcCtrlValue | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.40 | Unsigned32 | read-write | When 'Specific' is selected for the LLC control filter, you can enter a specific value. The allowed value is from 0x0 through 0xFF. |
| INT tnEvcEceLlcDataFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.41 | INTEGER | read-write | The LLC data for matching the ECE. The possible values are: Any: No LLC data filter is specified. (LLC filter status is 'don't-care'.) Specific: If you want to filter a specific LLC value with this ECE, choose this value. |
| U32 tnEvcEceLlcDataMask | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.43 | Unsigned32 | read-write | When 'Specific' is selected for the LLC data filter, you can enter a specific mask. The allowed value is from 0x0 through 0xFFFF. |
| U32 tnEvcEceLlcDataValue | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.42 | Unsigned32 | read-write | When 'Specific' is selected for the LLC data filter, you can enter a specific value. It is a pair of the LLC data and its mask. The allowed value is from 0x0 through 0xFFFF. |
| INT tnEvcEceLlcDSAPFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.35 | INTEGER | read-write | The LLC DSAP for matching the ECE. The possible values are: Any: No LLC DSAP value filter is specified. (LLC DSAP filter status is 'don't-care'.) Specific: If you want to filter a specific LLC DSAP value with this ECE, choose this value. |
| U32 tnEvcEceLlcDSAPValue | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.36 | Unsigned32 | read-write | When 'Specific' is selected for the LLC DSAP filter, you can enter a specific value. The allowed value is from 0x0 through 0xFF |
| INT tnEvcEceLlcSSAPFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.37 | INTEGER | read-write | The LLC SSAP for matching the ECE. The possible values are: Any: No LLC SSAP value filter is specified. (LLC SSAP filter status is 'don't-care'.) Specific: If you want to filter a specific LLC SSAP value with this ECE, choose this value. |
| U32 tnEvcEceLlcSSAPValue | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.38 | Unsigned32 | read-write | When 'Specific' is selected for the LLC SSAP filter, you can enter a specific value. The allowed value is from 0x0 through 0xFF. |
| INT tnEvcEceLookup | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.29 | INTEGER | read-write | The looup type for matching the ECE. The allowed values are: Basic: First lookup for basic classification. Advanced: Second lookup for advanced classification. |
| INT tnEvcEceNextEceId | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.2 | INTEGER | read-create | Specify the created ECE is placed before which ECE. |
| INT tnEvcEceNNIInnerTagType | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.10 | INTEGER | read-create | The inner type for the ECE determines whether an inner tag is inserted in frames forwarded to NNI ports.\ The possible values are: None: An inner tag is not inserted. C-tag: An inner C-tag is inserted. S-tag: An inner S-tag is inserted. S-custom-tag: An inner tag is inserted and the tag type is determined by the VLAN port configuration of the NNI. |
| INT tnEvcEceOuterDEI | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.36 | INTEGER | read-create | The outer tag DEI value for the ECE. The allowed value is 0 or 1. |
| INT tnEvcEceOuterDEIMode | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.17 | INTEGER | read-write | The outer tag DEI mode for the ECE. The possible values are: Classified: The outer tag DEI mode is classified. Fixed: The outer tag DEI mode is fixed. Drop Precedence: The outer tag DEI mode is drop precedence. |
| INT tnEvcEceOuterMode | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.33 | INTEGER | read-create | The outer tag PCP and DEI preservation for the ECE. The possible values are: enabled: Enable outer tag for nni-to-uni direction for the ECE. disabled: Disable outer tag for nni-to-uni direction for the ECE. |
| INT tnEvcEceOuterPCP | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.35 | INTEGER | read-create | The outer tag PCP value for the ECE. The allowed range is from 0 through 7. |
| INT tnEvcEceOuterPCPDEIPreserve | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.34 | INTEGER | read-create | The outer tag PCP and DEI preservation for the ECE. The possible values are: preserved: The outer tag PCP and DEI is preserved. fixed: The outer tag PCP and DEI is fixed. |
| INT tnEvcEceOuterPCPMode | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.16 | INTEGER | read-write | The outer tag PCP mode for the ECE. The possible values are: Classified: The outer tag PCP Mode is classified. Fixed: The outer tag PCP Mode is fixed. Mapped: The outer tag PCP Mode is based on mapped (QOS, DP). |
| VLA tnEvcEceOuterVid | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.9 | VlanIdOrNone | read-create | The EVC outer tag VID for UNI ports. The allowed value is from 0 through 4094. |
| INT tnEvcEcePolicer | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.8 | INTEGER | read-create | The ingress bandwidth profile mode for the EVC. The possible values are: Specific: The allowed range is from 1 through 128. Discard: All received frames are discarded for the EVC. The value is 4094. None: None bandwidth profile for the EVC. The value is 4095. EVC:The bandwidth profile for the specified EVC ID is used. The value is 4096. |
| INT tnEvcEceProtoType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.12 | INTEGER | read-create | The IP protocol for matching the ECE. The possible values are: any: No protocol filter is specified. (Protocol filter status is 'don't-care'.) udp: Specify the UDP for matching the ECE. tcp: Specify the TCP for matching the ECE. other: If you want to filter a specific protocol value with this ECE, choose this value. A field for entering a specific value appears. |
| INT tnEvcEceProtoVal | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.13 | INTEGER | read-create | When 'Specific' is selected for the protocol filter, you can enter a specific value. The allowed value is from 0 through 255. |
| INT tnEvcEceSnapOuiFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.44 | INTEGER | read-write | The SNAP OUI for matching the ECE. The possible values are: Any: No SNAP OUI value filter is specified. (SNAP OUI filter status is 'don't-care'.) Specific: If you want to filter a specific SNAP OUI value with this ECE, choose this value. |
| U32 tnEvcEceSnapOuiValue | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.45 | Unsigned32 | read-write | When 'Specific' is selected for the SNAP OUI filter, you can enter a specific value. The allowed value is from 00-00-00 through FF-FF-FF. |
| INT tnEvcEceSnapPidFilter | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.46 | INTEGER | read-write | The SNAP PID for matching the ECE. The possible values are: Any: No SNAP PID value filter is specified. (SNAP PID filter status is 'don't-care'.) Specific: If you want to filter a specific SNAP PID value with this ECE, choose this value. |
| U32 tnEvcEceSnapPidValue | 1.3.6.1.4.1.868.2.5.106.1.1.5.1.47 | Unsigned32 | read-write | When 'Specific' is selected for the SNAP PID filter, you can enter a specific value. The allowed value is from 0x0 through 0xFFFF. |
| INT tnEvcEceSrcPortFilterNo | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.19 | INTEGER | read-create | When 'Specific' is selected for the source port filter, you can enter a specific value. The allowed value is from 0 through 65535. |
| INT tnEvcEceSrcPortFilterType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.18 | INTEGER | read-create | The TCP/UDP source port for matching the ECE. It only significant if protocol filter 'UDP' or 'TCP' is selected. The possible values are: any: No TCP/UDP source port filter is specified. (Source port filter status is 'don't-care'.) specific: If you want to filter a specific TCP/UDP source port No. with this ECE, choose this value. A field for entering a specific No. appears. range: If you want to filter a specific TCP/UDP source port range filter with this ECE, choose this value. A field for entering a range appears. |
| INT tnEvcEceSrcPortRangeEnd | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.21 | INTEGER | read-create | When 'Range' is selected for the source port filter, you can enter a specific range. The allowed range end is from 0 through 65535. |
| INT tnEvcEceSrcPortRangeStart | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.20 | INTEGER | read-create | When 'Range' is selected for the source port filter, you can enter a specific range. The allowed range start is from 0 through 65535. |
| ROW tnEvcEceStatus | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.47 | RowStatus | read-create | The status of this conceptual row entry of ECE table. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. For a detailed description of this object, please refer to SNMPv2-TC MIB. |
| tnEvcEceTable | 1.3.6.1.4.1.868.2.5.106.1.1.3 | not-accessible | This table contains the configuration of EVC control entry. | |
| INT tnEvcEceTagDEI | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.10 | INTEGER | read-create | The DEI value for mataching the ECE. It only significant if tag type 'Tagged' is selected. The allowed value is: 0, 1 or Any. |
| INT tnEvcEceTagFrameType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.11 | INTEGER | read-create | The frame type for the ECE. The possible values are: any: The ECE will match any frame type. etype: The ECE will match Ethernet Type frames only. llc: The ECE will match LLC frames only. snap: The ECE will match SNAP frames only. ipv4: The ECE will match IPv4 frames only. ipv6: The ECE will match IPv6 frames only. l2cp: The ECE will match L2CP frames only. |
| BIT tnEvcEceTagPCP | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.9 | Bits | read-create | The PCP value for mataching the ECE. It only significant if tag type 'Tagged' is selected. The possible values are: any: The ECE will match any PCP value(all bits will be set to 1). specific: each bit matchs a specific PCP of ECE(from bit0 to bit7). range: The ECE will match PCP values in the selected range, valid range bit0-bit1, bit2-bit3, bit4-bit5, bit6-bit7, bit0-bit3 or bit4-bit7. |
| INT tnEvcEceTagType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.4 | INTEGER | read-create | The tag type for the ECE. The possible values are: tagged: The ECE will match tagged frames only. untagged: The ECE will match untagged frames only. any: The ECE will match both tagged and untagged frames. |
| VLA tnEvcEceTagVIDFilterEnd | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.8 | VlanIdOrAnyOrNone | read-create | When 'Range' is selected for the VLAN ID filter, you can enter a specific range. The allowed range end is from 0 through 4094. |
| VLA tnEvcEceTagVIDFilterStart | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.7 | VlanIdOrAnyOrNone | read-create | When 'Range' is selected for the VLAN ID filter, you can enter a specific range. The allowed range start is from 0 through 4094. |
| INT tnEvcEceTagVIDFilterType | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.5 | INTEGER | read-create | The VLAN ID filter for matching the ECE. It only significant if tag type 'Tagged' is selected. The possible values are: any: No VLAN ID filter is specified. (VLAN ID filter status is 'don't-care'.) specific: If you want to filter a specific VLAN ID value with this ECE, choose this value. A field for entering a specific value appears. range: If you want to filter a specific VLAN ID range filter with this ECE, choose this value. A field for entering a range appears. |
| VLA tnEvcEceTagVIDFilterVal | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.6 | VlanIdOrAnyOrNone | read-create | When 'Specific' is selected for the VLAN ID filter, you can enter a specific value. The allowed value is from 0 through 4094. |
| POR tnEvcEceUNIPortlist | 1.3.6.1.4.1.868.2.5.106.1.1.3.1.3 | PortList | read-create | The list of User to Network Interfaces for the ECE. |
| tnEvcEntry | 1.3.6.1.4.1.868.2.5.106.1.1.2.1 | not-accessible | This entry represents an EVC. Each entry in this table represents an EVC and can be created or deleted by the management system. | |
| tnEvcExtEceEntry | 1.3.6.1.4.1.868.2.5.106.1.1.5.1 | not-accessible | This entry represents an ECE. The system automatically creates an entry when the system or the EMS/NMS creates a row in the cevcECETable. Likewise, the system automatically destroys an entry when the system or the EMS/NMS destroys the corresponding row in the cevcECETable. | |
| tnEvcExtEceTable | 1.3.6.1.4.1.868.2.5.106.1.1.5 | not-accessible | This table contains the configuration of EVC control entry. | |
| T/F tnEvcExtStatclear | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.18 | TruthValue | read-write | Clear the value by EVC or ECE index. |
| C64 tnEvcExtStatDiscardBytesRx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.16 | Counter64 | read-only | The number Bytes of discarded received. |
| C64 tnEvcExtStatDiscardBytesTx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.17 | Counter64 | read-only | The number Bytes of discarded transmitted. |
| C64 tnEvcExtStatDiscardFrameRx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.14 | Counter64 | read-only | The number Frames of discarded received. |
| C64 tnEvcExtStatDiscardFrameTx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.15 | Counter64 | read-only | The number Frames of discarded transmitted. |
| tnEvcExtStatEntry | 1.3.6.1.4.1.868.2.5.106.1.2.2.1 | not-accessible | This entry represents an entry of EVC statistics. | |
| C64 tnEvcExtStatGreenBytesRx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.6 | Counter64 | read-only | The number Bytes of green received. |
| C64 tnEvcExtStatGreenBytesTx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.7 | Counter64 | read-only | The number Bytes of green transmitted. |
| C64 tnEvcExtStatGreenFrameRx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.4 | Counter64 | read-only | The number Frames of green received. |
| C64 tnEvcExtStatGreenFrameTx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.5 | Counter64 | read-only | The number Frames of green transmitted. |
| INT tnEvcExtStatIndex | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.2 | INTEGER | not-accessible | The EVC or ECE index. |
| INT tnEvcExtStatPort | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.3 | INTEGER | not-accessible | The EVC or ECE index. |
| C64 tnEvcExtStatRedBytesRx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.13 | Counter64 | read-only | The number Bytes of red received. |
| C64 tnEvcExtStatRedFrameRx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.12 | Counter64 | read-only | The number Frames of red received. |
| tnEvcExtStatTable | 1.3.6.1.4.1.868.2.5.106.1.2.2 | not-accessible | This table provides port traffic statistics for the selected EVC. It also shows counters for UNI ports of ECEs mapping to the EVC. | |
| INT tnEvcExtStatType | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.1 | INTEGER | not-accessible | The traffic class for the EVC. |
| C64 tnEvcExtStatYellowBytesRx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.10 | Counter64 | read-only | The number Bytes of yellow received. |
| C64 tnEvcExtStatYellowBytesTx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.11 | Counter64 | read-only | The number Bytes of yellow transmitted. |
| C64 tnEvcExtStatYellowFrameRx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.8 | Counter64 | read-only | The number Frames of yellow received. |
| C64 tnEvcExtStatYellowFrameTx | 1.3.6.1.4.1.868.2.5.106.1.2.2.1.9 | Counter64 | read-only | The number Frames of yellow transmitted. |
| tnEvcGroups | 1.3.6.1.4.1.868.2.5.106.1.8.1 | |||
| INT tnEvcIndex | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.1 | INTEGER | not-accessible | The identifier of the EVC. |
| INT tnEvcInnerDEI | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.11 | INTEGER | read-create | The inner tag DEI value. The allowed value is 0 or 1. |
| INT tnEvcInnerPCP | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.10 | INTEGER | read-create | The inner tag PCP value. The allowed range is from 0 through 7. |
| INT tnEvcInnerPCPDEIPreservation | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.9 | INTEGER | read-create | The inner tag PCP and DEI preservation. The allowed values are: Preserved: The inner tag PCP and DEI is preserved. Fixed: The inner tag PCP and DEI is fixed. |
| INT tnEvcInnerTagType | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.6 | INTEGER | read-create | The inner tag type is used to determine whether an inner tag is inserted in frames forwarded to NNI ports. The allowed values are: None: An inner tag is not inserted. cTag: An inner C-tag is inserted. sTag: An inner S-tag is inserted. sCustomTag: An inner tag is inserted and the tag type is determined by the VLAN port configuration of the NNI. |
| VLA tnEvcInnerVid | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.8 | VlanIdOrAnyOrNone | read-create | The Inner tag VLAN ID. The allowed range is from 0 through 4094. |
| INT tnEvcInnerVidMode | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.7 | INTEGER | read-create | The inner VID Mode affects the VID in the inner and outer tag. The allowed values are: normal: The VID of the two outer tags aren't swapped. tunnel: The VID of the two outer tags are swapped, so that the VID of the outer tag is taken from the Inner Tag configuration and the VID of the inner tag is the EVC VID. In this mode, the NNI ports are normally configured to do EVC classification based on the inner tag. |
| VLA tnEvcIVid | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.4 | VlanIdOrAny | read-create | The Internal/classified VLAN ID in the PB network. The allowed range is from 1 through 4094 |
| tnEvcJaguarPortConfigGroup | 1.3.6.1.4.1.868.2.5.106.1.8.1.2 | The collection of objects which are used to configure or describe the configuration or behavior of the S4140. | ||
| tnEvcL2cpCfgEntry | 1.3.6.1.4.1.868.2.5.106.1.3.3.1 | not-accessible | L2CP settings table entry. | |
| OCT tnEvcL2cpCfgEvcName | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.8 | OCTET STRING | read-create | Sets L2CP EVC association. |
| U32 tnEvcL2cpCfgIndex | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.2 | Unsigned32 | not-accessible | Sets L2CP index number on an interface. |
| U32 tnEvcL2cpCfgInterfaceNumber | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.1 | Unsigned32 | not-accessible | Sets L2CP interface number. |
| MAC tnEvcL2cpCfgMacAddress | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.5 | MacAddress | read-create | Sets L2CP Destination MAC address. |
| INT tnEvcL2cpCfgMatchScope | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.4 | INTEGER | read-create | Sets L2CP selection matching scope. |
| U32 tnEvcL2cpCfgProtocol | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.6 | Unsigned32 | read-create | Sets L2CP protocol. |
| ROW tnEvcL2cpCfgRowStatus | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.10 | RowStatus | read-create | The status of the row. The writable columns in a row cannot be changed if the row is active. All columns must have a valid value before a row can be activated. |
| U32 tnEvcL2cpCfgSubType | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.7 | Unsigned32 | read-create | Sets L2CP subtype for the protocol selected. |
| tnEvcL2cpCfgTable | 1.3.6.1.4.1.868.2.5.106.1.3.3 | not-accessible | This table supports L2CP settings. | |
| INT tnEvcL2cpCfgType | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.3 | INTEGER | read-create | Sets L2CP type setting. |
| INT tnEvcL2cpCfgValid | 1.3.6.1.4.1.868.2.5.106.1.3.3.1.9 | INTEGER | read-create | Sets L2CP valid instance. |
| tnEvcL2cpMgmtGroup | 1.3.6.1.4.1.868.2.5.106.1.3 | |||
| INT tnEvcLearning | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.5 | INTEGER | read-create | The learning mode for the EVC controls whether source MAC addresses are learned for frames matching the EVC. Learning may be disabled if the EVC only includes two UNI/NNI ports. The allowed values are: Enabled: Learning is enabled (MAC addresses are learned). Disabled: Learning is disabled (MAC addresses are not learned). |
| tnEvcMib | 1.3.6.1.4.1.868.2.5.106 | TBD | ||
| OCT tnEvcName | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.15 | OCTET STRING | read-create | EVC Administrative Name. |
| POR tnEvcNNIPortlist | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.2 | PortList | read-create | The list of Network to Network Interfaces for the EVC. |
| tnEvcObjects | 1.3.6.1.4.1.868.2.5.106.1 | |||
| VLA tnEvcOuterVid | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.12 | VlanIdOrAnyOrNone | read-create | The Outer tag VLAN ID. The allowed range is from 0 through 4094. |
| INT tnEvcPolicerID | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.14 | INTEGER | read-create | The ingress bandwidth profile mode for the EVC. The possible values are: Specific: The allowed range is from 1 through 128. Discard: All received frames are discarded for the EVC. The value is 4094. None: None bandwidth profile for the EVC. The value is 4095. |
| INT tnEvcPortAddressMode | 1.3.6.1.4.1.868.2.5.106.1.1.1.1.3 | INTEGER | read-write | The IP/MAC address mode specifying whether the EVC classification must be based on source (SMAC/SIP) or destination (DMAC/DIP) addresses. The allowed values are: 'source': Enable SMAC/SIP matching. 'destination': Enable DMAC/DIP matching. |
| tnEvcPortConfigGroup | 1.3.6.1.4.1.868.2.5.106.1.8.1.1 | The collection of objects which are used to configure or describe the configuration or behavior of the S3280. | ||
| INT tnEvcPortDEIMode | 1.3.6.1.4.1.868.2.5.106.1.1.1.1.1 | INTEGER | read-write | The DEI mode for an NNI port determines whether frames transmitted on the port will have the DEI field in the outer tag marked based on the colour of the frame. The allowed values are: 'coloured': The DEI is 1 for yellow frames and 0 for green frames. 'fixed': The DEI value is determined by ECE rules. |
| tnEvcPortEntry | 1.3.6.1.4.1.868.2.5.106.1.1.1.1 | not-accessible | This entry represents an EVC port configuration. | |
| tnEvcPortTable | 1.3.6.1.4.1.868.2.5.106.1.1.1 | not-accessible | This table displays and sets current EVC port configurations. This table has a sparse depedent relationship on the ifTable, containing a row for each ifEntry having an ifType of 'ethernetCsmacd' capable of supporting Ethernet services. | |
| INT tnEvcPortTagMode | 1.3.6.1.4.1.868.2.5.106.1.1.1.1.2 | INTEGER | read-write | The inner tag type is used to determine whether an inner tag is inserted in frames forwarded to NNI ports. The possible values are: 'inner': An inner tag is not inserted. 'outer': An inner C-tag is inserted. |
| INT tnEvcStatClass | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.1 | INTEGER | not-accessible | The traffic class for the EVC. |
| T/F tnEvcStatClear | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.9 | TruthValue | read-write | Clears the counters for selected ports when the value of tnEvcStatClear is true. |
| C64 tnEvcStatDiscardGreenFrame | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.7 | Counter64 | read-only | The number of discarded in the green color. |
| C64 tnEvcStatDiscardYellowFrame | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.8 | Counter64 | read-only | The number of discarded in the yellow color. |
| tnEvcStatEntry | 1.3.6.1.4.1.868.2.5.106.1.2.1.1 | not-accessible | This entry represents an entry of EVC statistics. | |
| C64 tnEvcStatGreenFrameRxEx | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.2 | Counter64 | read-only | The number of green received. |
| C64 tnEvcStatGreenFrameTx | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.3 | Counter64 | read-only | The number of green transmitted. |
| tnEvcStatGroup | 1.3.6.1.4.1.868.2.5.106.1.2 | |||
| C64 tnEvcStatRedFrameRx | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.6 | Counter64 | read-only | The number of red received. |
| tnEvcStatTable | 1.3.6.1.4.1.868.2.5.106.1.2.1 | not-accessible | This table provides NNI port traffic statistics for the selected EVC. It also shows counters for UNI ports of ECEs mapping to the EVC. | |
| ROW tnEvcStatus | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.13 | RowStatus | read-create | The status of this conceptual row entry of EVC table. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. For a detailed description of this object, please refer to SNMPv2-TC MIB. |
| C64 tnEvcStatYellowFrameRx | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.4 | Counter64 | read-only | The number of yellow received. |
| C64 tnEvcStatYellowFrameTx | 1.3.6.1.4.1.868.2.5.106.1.2.1.1.5 | Counter64 | read-only | The number of yellow transmitted. |
| tnEvcTable | 1.3.6.1.4.1.868.2.5.106.1.1.2 | not-accessible | This table contains the configuration of EVC(Ethernet Virtual Circuit). | |
| tnEvcTableGroup | 1.3.6.1.4.1.868.2.5.106.1.8.1.3 | The collection of objects which are used to configure or describe the configuration or behavior of the S4140. | ||
| VLA tnEvcVid | 1.3.6.1.4.1.868.2.5.106.1.1.2.1.3 | VlanIdOrAny | read-create | The VLAN ID in the PB network. It may be inserted in a C-tag, S-tag or S-custom tag depending on the NNI port VLAN configuration. The allowed range is from 1 through 4094 |
RFC description
Ethernet Virtual Circuit (EVC) MIB for transport networks. Manages E-Line, E-LAN, and E-Tree services as defined by Metro Ethernet Forum.
Start monitoring Transition Networks managed media converters/switches (Ethernet Virtual Circuit VLAN/tagging config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.