TELTONIKA-RUTX-MIB

All MIBs › TELTONIKA-RUTX-MIB

Organization: TELTONIKA

Last Updated: 2019-05-15

Category: Industrial and Cellular Routers, Wireless and Cellular Networking

Description: Manages Teltonika RUTX series industrial router advanced features, dual-SIM failover, and extended cellular interface data.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TELTONIKA-RUTX-MIB?

TELTONIKA-RUTX-MIB is a vendor-specific MIB for Teltonika's RUTX series of industrial/M2M cellular routers, covering device identification and advanced router features like dual-SIM cellular failover. It exposes hardware inventory data (serial number, product code, batch number, hardware revision) alongside firmware version and a modem table describing installed cellular modems. Its monitoring value spans both hardware and software status: administrators can confirm the running firmware version (fwVersion), verify hardware identity/revision for asset tracking, and inspect per-modem details (via modemTable/modemEntry) including GPS and mobile connectivity state, which is critical for routers deployed in remote or mobile industrial sites. It is a self-contained Teltonika enterprise MIB but is commonly used alongside standard IF-MIB and mobile-specific objects for full connectivity visibility. It is deployed in industrial IoT, fleet, and remote-site networking scenarios where RUTX routers provide primary or backup cellular WAN connectivity. Engineers can download the TELTONIKA-RUTX-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TELTONIKA-RUTX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Teltonika RUTX series industrial/cellular router

Monitoring Examples

An administrator reads fwVersion and hardwareRevision to confirm a fleet of RUTX routers is running the expected firmware before pushing a configuration update, and checks serial and productCode to reconcile device inventory. Polling modemTable (modemEntry, keyed by mIndex, with mDescr) across dual-SIM units reveals which modem is currently active and its description, helping diagnose a stalled SIM failover. The mobile and gps object groups would additionally be checked to confirm cellular signal and location reporting are functioning for a remote-deployed router.

What Can Be Monitored

firmware version
hardware revision and serial number
modem/SIM status
product/batch identification
GPS and mobile connectivity state

Imported Objects

From RFC1155-SMI

NetworkAddress

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Opaque
enterprises

From SNMPv2-TC

DisplayString
PhysAddress
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using hsSessionCount OID:

Select a Teltonika RUTX series industrial/cellular router (hardware identity/firmware/modem status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hsSessionCount into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of sessions. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
STR accuracy	1.3.6.1.4.1.48690.3.3	DisplayString	read-only	Accuracy
STR batchNumber	1.3.6.1.4.1.48690.1.4	DisplayString	read-only	Router batch number
NTF connectionTypeNotification	1.3.6.1.4.1.48690.4.1.2			Connection type trap
STR datetime	1.3.6.1.4.1.48690.3.4	DisplayString	read-only	GPS datetime
device	1.3.6.1.4.1.48690.1
NTF digitalInputNotification	1.3.6.1.4.1.48690.4.2.1			Digital input trap
NTF digitalOutputNotification	1.3.6.1.4.1.48690.4.2.2			Digital output trap
STR dinState	1.3.6.1.4.1.48690.4.2.0.1	DisplayString	read-only	Digital input state
STR doutState	1.3.6.1.4.1.48690.4.2.0.2	DisplayString	read-only	Digital output state
STR fwVersion	1.3.6.1.4.1.48690.1.6	DisplayString	read-only	Router firmware version
gps	1.3.6.1.4.1.48690.3
STR hardwareRevision	1.3.6.1.4.1.48690.1.5	DisplayString	read-only	Router hardware revision
hotspot	1.3.6.1.4.1.48690.5
STR hsAuth	1.3.6.1.4.1.48690.5.4	DisplayString	read-only	Authentication mode
IP hsIP	1.3.6.1.4.1.48690.5.2	IpAddress	read-only	The IPv4 address
STR hsNet	1.3.6.1.4.1.48690.5.3	DisplayString	read-only	Network interfaces
C64 hssDwBandwidth	1.3.6.1.4.1.48690.5.6.1.11	Counter64	read-only	Max download bandwidth in b/s. Cannot be accessed using SNMPv1.
C64 hssDwLimit	1.3.6.1.4.1.48690.5.6.1.7	Counter64	read-only	Download limit in bytes. Cannot be accessed using SNMPv1.
C64 hsSessionCountEx	1.3.6.1.4.1.48690.5.5	Counter64	read-only	Number of sessions
hsSessionEntry	1.3.6.1.4.1.48690.5.6.1		not-accessible	An entry containing information of a particular hotspot session.
hsSessionTable	1.3.6.1.4.1.48690.5.6		not-accessible	A list of hotspot session entries. The number of entries is given by the value of hsSessionNum.
STR hssID	1.3.6.1.4.1.48690.5.6.1.4	DisplayString	read-only	Session ID
I32 hssIdleTimeout	1.3.6.1.4.1.48690.5.6.1.10	Integer32	read-only	Idle timeout in sec.
INT hssIndex	1.3.6.1.4.1.48690.5.6.1.1	INTEGER	read-only	A unique value, greater than zero, for each session.
IP hssIP	1.3.6.1.4.1.48690.5.6.1.3	IpAddress	read-only	Clients IP address
PHY hssMAC	1.3.6.1.4.1.48690.5.6.1.2	PhysAddress	read-only	Clients MAC address
INT hssState	1.3.6.1.4.1.48690.5.6.1.6	INTEGER	read-only	Session state
INT hsState	1.3.6.1.4.1.48690.5.1	INTEGER	read-only	Hotspot state
C64 hssTimeLimit	1.3.6.1.4.1.48690.5.6.1.9	Counter64	read-only	Time limit in sec. Cannot be accessed using SNMPv1.
C64 hssUpBandwidth	1.3.6.1.4.1.48690.5.6.1.12	Counter64	read-only	Max upwnload bandwidth in b/s. Cannot be accessed using SNMPv1.
C64 hssUpLimit	1.3.6.1.4.1.48690.5.6.1.8	Counter64	read-only	Upload limit in bytes. Cannot be accessed using SNMPv1.
STR hssURL	1.3.6.1.4.1.48690.5.6.1.13	DisplayString	read-only	Original URL
STR hssUsername	1.3.6.1.4.1.48690.5.6.1.5	DisplayString	read-only	Username
io	1.3.6.1.4.1.48690.6
INT ioBidirectional	1.3.6.1.4.1.48690.6.2.1.5	INTEGER	read-only	Is I/O bidirectional?
INT ioCount	1.3.6.1.4.1.48690.6.1	INTEGER	read-only	Count of I/O
STR ioCurrent	1.3.6.1.4.1.48690.6.2.1.9	DisplayString	read-only	Current amount flowing though ACL.
ioEntry	1.3.6.1.4.1.48690.6.2.1		not-accessible	An entry containing information of a particular I/O.
INT ioIndex	1.3.6.1.4.1.48690.6.2.1.1	INTEGER	read-only	A unique value, greater than zero, for each session.
INT ioInput	1.3.6.1.4.1.48690.6.2.1.7	INTEGER	read-only	Is I/O an input?
INT ioInverted	1.3.6.1.4.1.48690.6.2.1.8	INTEGER	read-only	Is value of I/O inverted?
STR ioName	1.3.6.1.4.1.48690.6.2.1.3	DisplayString	read-only	The name of the I/O, as displayed in WebUI.
ioNotifications	1.3.6.1.4.1.48690.4.2
ioNotificationsObs	1.3.6.1.4.1.48690.4.2.0
STR ioPercentage	1.3.6.1.4.1.48690.6.2.1.10	DisplayString	read-only	Percentage of ACL.
STR ioState	1.3.6.1.4.1.48690.6.2.1.6	DisplayString	read-only	State of I/O.
STR ioSystemName	1.3.6.1.4.1.48690.6.2.1.2	DisplayString	read-only	The name of the I/O.
ioTable	1.3.6.1.4.1.48690.6.2		not-accessible	A list of I/O. The number of entries is given by the value of ioCount.
STR ioType	1.3.6.1.4.1.48690.6.2.1.4	DisplayString	read-only	A description of I/O type.
STR latitude	1.3.6.1.4.1.48690.3.1	DisplayString	read-only	Latitutde coordinates
STR longtitude	1.3.6.1.4.1.48690.3.2	DisplayString	read-only	Longtitude coordinates
STR mCellID	1.3.6.1.4.1.48690.2.2.1.18	DisplayString	read-only	CELL ID
STR mConnectionState	1.3.6.1.4.1.48690.2.2.1.15	DisplayString	read-only	Sata session connection state
STR mConnectionType	1.3.6.1.4.1.48690.2.2.1.16	DisplayString	read-only	Data session connection type
STR mDescr	1.3.6.1.4.1.48690.2.2.1.2	DisplayString	read-only	A textual string containing information about the modem.
STR mImei	1.3.6.1.4.1.48690.2.2.1.3	DisplayString	read-only	Modem IMEI
STR mIMSI	1.3.6.1.4.1.48690.2.2.1.8	DisplayString	read-only	IMSI
I32 mIndex	1.3.6.1.4.1.48690.2.2.1.1	Integer32	read-only	A unique value, greater than zero, for each modem.
STR mIP	1.3.6.1.4.1.48690.2.2.1.24	DisplayString	read-only	Modem IP address(es)
STR mManufacturer	1.3.6.1.4.1.48690.2.2.1.5	DisplayString	read-only	Modem manufacturer
STR mModel	1.3.6.1.4.1.48690.2.2.1.4	DisplayString	read-only	Modem model
STR mNetState	1.3.6.1.4.1.48690.2.2.1.11	DisplayString	read-only	Mobile network registration status
mobile	1.3.6.1.4.1.48690.2
mobileNotifications	1.3.6.1.4.1.48690.4.1
modemEntry	1.3.6.1.4.1.48690.2.2.1		not-accessible	An entry containing information of a particular interface.
I32 modemNum	1.3.6.1.4.1.48690.2.1	Integer32	read-only	The number of modems (regardless of their current state) present on this system.
modemTable	1.3.6.1.4.1.48690.2.2		not-accessible	A list of modem entries. The number of entries is given by the value of modemNum.
STR mOperator	1.3.6.1.4.1.48690.2.2.1.13	DisplayString	read-only	Operator currently in use
STR mOperatorNumber	1.3.6.1.4.1.48690.2.2.1.14	DisplayString	read-only	Operator number (MCC+MNC)
STR mPinState	1.3.6.1.4.1.48690.2.2.1.10	DisplayString	read-only	PIN status
C64 mReceived	1.3.6.1.4.1.48690.2.2.1.23	Counter64	read-only	Total bytes received.
C64 mReceivedToday	1.3.6.1.4.1.48690.2.2.1.26	Counter64	read-only	Bytes received today.
STR mRevision	1.3.6.1.4.1.48690.2.2.1.6	DisplayString	read-only	Modem revision
STR mRSRP	1.3.6.1.4.1.48690.2.2.1.20	DisplayString	read-only	LTE RSRP level
STR mRSRQ	1.3.6.1.4.1.48690.2.2.1.21	DisplayString	read-only	LTE RSRQ level
C64 mSent	1.3.6.1.4.1.48690.2.2.1.22	Counter64	read-only	Total bytes sent.
C64 mSentToday	1.3.6.1.4.1.48690.2.2.1.25	Counter64	read-only	Bytes sent today.
STR mSerial	1.3.6.1.4.1.48690.2.2.1.7	DisplayString	read-only	Serial number
INT mSignal	1.3.6.1.4.1.48690.2.2.1.12	INTEGER	read-only	Signal level
STR mSimState	1.3.6.1.4.1.48690.2.2.1.9	DisplayString	read-only	SIM status
STR mSINR	1.3.6.1.4.1.48690.2.2.1.19	DisplayString	read-only	LTE SINR level
INT mTemperature	1.3.6.1.4.1.48690.2.2.1.17	INTEGER	read-only	Modem temperature
notifications	1.3.6.1.4.1.48690.4
I32 numSatellites	1.3.6.1.4.1.48690.3.5	Integer32	read-only	Number of satellites
STR productCode	1.3.6.1.4.1.48690.1.3	DisplayString	read-only	Router product code
STR routerName	1.3.6.1.4.1.48690.1.2	DisplayString	read-only	Router name
STR serial	1.3.6.1.4.1.48690.1.1	DisplayString	read-only	Serial number
NTF signalChangeNotification	1.3.6.1.4.1.48690.4.1.1			Signal strength trap
teltonika	1.3.6.1.4.1.48690			The MIB module for TELTONIKA rutx routers.

RFC description

Teltonika RUTX industrial router monitoring including GPS, mobile, and I/O notifications.

Start monitoring Teltonika RUTX series industrial/cellular router (hardware identity/firmware/modem status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TELTONIKA-RUTX-MIB