TELESTE-LUMINATO-MIB

All MIBs › TELESTE-LUMINATO-MIB

Category: Broadcast and Cable TV Equipment

Description: Manages Teleste Luminato cable TV optical node configuration, RF levels, and downstream performance parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TELESTE-LUMINATO-MIB?

This MIB module manages Teleste's Luminato line of cable-TV optical nodes, part of the vendor's HFC (hybrid fiber-coax) access network product family. It exposes configuration and status data for the optical node, including RF output levels and downstream signal performance parameters that describe the quality of the broadcast signal delivered to subscribers. It is used to monitor both hardware health, such as RF/optical signal levels and likely temperature/power-supply status typical of outdoor optical nodes, and operational configuration of the node, helping operators detect signal degradation before it affects subscriber video/data service. As a cable-industry access device it likely coexists with DOCSIS-related MIBs on the broader HFC network but is itself a Teleste-proprietary management module. It is deployed by cable TV/MSO (multi-system operator) network operators managing fiber-to-the-node infrastructure in outside-plant locations. Network engineers evaluating or troubleshooting this functionality can download the TELESTE-LUMINATO-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TELESTE-LUMINATO-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Teleste Luminato optical node (cable TV/HFC network)

Monitoring Examples

A cable engineer would poll the node's downstream RF-level objects to confirm output power stays within the target range for a given service group, since drift here directly affects subscriber signal quality. Configuration objects covering modulation and downstream performance parameters would be checked after a node truck-roll to confirm settings match the design plan. Because Luminato nodes are outdoor optical-to-RF converters, operators would also expect status objects reflecting the node's internal environmental and power health as part of routine outside-plant monitoring.

What Can Be Monitored

RF output power/levels
downstream signal performance
node configuration parameters
optical node operational status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

TimeTicks

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

Counter32
Unsigned32

From TELESTE-ROOT-MIB

luminato

OBJECT-IDENTITY

From UCD-SNMP-MIB

Float

OIDs

OID symbolic	OID numeric	Type	Access	Description
general	1.3.6.1.4.1.3715.17.1
STR deviceName	1.3.6.1.4.1.3715.17.1.1	DisplayString	read-write	The identification name ('aliasname') of the device
INT generalStatus	1.3.6.1.4.1.3715.17.1.2	INTEGER	read-only	General status of device
INT redundancyStatus	1.3.6.1.4.1.3715.17.1.3	INTEGER	read-only	Status of device in 1+1 backup operation mode
STR hwSerialNumber	1.3.6.1.4.1.3715.17.1.10	DisplayString	read-only	Device serial number
STR hwType	1.3.6.1.4.1.3715.17.1.11	DisplayString	read-only	The hardware type name of the device
STR hwVersion	1.3.6.1.4.1.3715.17.1.12	DisplayString	read-only	Device hardware version
STR swVersion	1.3.6.1.4.1.3715.17.1.13	DisplayString	read-only	Device running software version
TIK upTime	1.3.6.1.4.1.3715.17.1.14	TimeTicks	read-only	Device uptime
TIK cumulativeUptime	1.3.6.1.4.1.3715.17.1.15	TimeTicks	read-only	Device cummulative uptime
statusCode	1.3.6.1.4.1.3715.17.2
interfaceTypeTable	1.3.6.1.4.1.3715.17.2.1		not-accessible	InterfaceTypeTable lists possible interface types in the system.
interfaceTypeEntry	1.3.6.1.4.1.3715.17.2.1.1		not-accessible	Each InterfaceTypeEntry describes type of the interface.
INT interfaceTypeId	1.3.6.1.4.1.3715.17.2.1.1.1	INTEGER	not-accessible	Interfacetype Id has two values input(1) and output(2). Values are used in other tables as index.
statusCodeDeviceTable	1.3.6.1.4.1.3715.17.2.2		not-accessible	This table describes monitorable objects of the device. The objects may represents real objects or classes. The monitoring system or user shall not poll this table to detect device state. Instead - user shall wait for traps or poll currentAlarmTable(1.3.6.1.4.1.5591.1.1.2) from SCTE-HMS-PROPERTY-MIB. In this case statusCodeDeviceTable shall be used to obtains text definition of alarm.
statusCodeDeviceEntry	1.3.6.1.4.1.3715.17.2.2.1		not-accessible
U32 scdObjectId	1.3.6.1.4.1.3715.17.2.2.1.1	Unsigned32	read-only	Unique identifier of the monitorable object.
INT scdObjectValue	1.3.6.1.4.1.3715.17.2.2.1.2	INTEGER	read-only	Value of the monitorable object. The scdObjectDescriptor tells name, scale and unit of the object.
STR scdObjectDescriptor	1.3.6.1.4.1.3715.17.2.2.1.3	DisplayString	read-only	Description of the monitorable object. Free text if object has two states or Format: Name, Scale, Unit, [optional text] ------------------------------------ Example 1 (Analogue object): 'MainVoltage, 0.01, V' Usage: scdObjectId:7 (example) scdObjectValue:2399 scdObjectDescriptor:'MainVoltage, 0.01, V' means Main voltage is 23.99 V ------------------------------------ Example 2 (Discrete object): 'TemperatureHigh, 1, high(2)/nominal(1), Alarm state of the temperature' Usage: scdObjectId:12 (example) scdObjectValue:2 means Temperature is in high alarm state. ------------------------------------
INT scdObjectAlarmValue	1.3.6.1.4.1.3715.17.2.2.1.4	INTEGER	read-only	When the object has this value it is in the alarm state. One object id can have only one alarm state. If more alarm states exist then new associated object needs to be created. Note that alarm state value can have only discrete values. If the value is zero then there is no alarm for this object. Example: TemperatureHigh object can have values high(2) or nominal(1). Alarm monitoring for this object is triggered by setting dmObjectAlarmValue to value 2 meaning high(2). How the alarm processing is done is out of scope of this MIB.
statusCodeModuleTable	1.3.6.1.4.1.3715.17.2.3		not-accessible	This table describes monitorable objects per module inside the device. The objects may represents real objects or classes. The monitoring system or user shall not poll this table to detect device state. Instead - user shall wait for traps or poll currentAlarmTable(1.3.6.1.4.1.5591.1.1.2) from SCTE-HMS-PROPERTY-MIB. In this case statusCodeModuleTable shall be used to obtains text definition of alarm.
statusCodeModuleEntry	1.3.6.1.4.1.3715.17.2.3.1		not-accessible
INT scmModuleId	1.3.6.1.4.1.3715.17.2.3.1.1	INTEGER	read-only	Module Id within the device (usually slot number).
U32 scmObjectId	1.3.6.1.4.1.3715.17.2.3.1.2	Unsigned32	read-only	Unique identifier of the monitorable object within the module.
INT scmObjectValue	1.3.6.1.4.1.3715.17.2.3.1.3	INTEGER	read-only	Value of the monitorable object. The scmObjectDescriptor tells name, scale and unit of the object.
STR scmObjectDescriptor	1.3.6.1.4.1.3715.17.2.3.1.4	DisplayString	read-only	Description of the monitorable object. See scdObjectDescriptor for format, example and usage.
INT scmObjectAlarmValue	1.3.6.1.4.1.3715.17.2.3.1.5	INTEGER	read-only	See scdObjectAlarmValue for format, example and usage.
statusCodeInterfaceTable	1.3.6.1.4.1.3715.17.2.4		not-accessible	This table describes monitorable objects per interface per module. The objects may represents real objects or classes. The monitoring system or user shall not poll this table to detect device state. Instead - user shall wait for traps or poll currentAlarmTable(1.3.6.1.4.1.5591.1.1.2) from SCTE-HMS-PROPERTY-MIB. In this case statusCodeInterfaceTable shall be used to obtains text definition of alarm.
statusCodeInterfaceEntry	1.3.6.1.4.1.3715.17.2.4.1		not-accessible
INT sciInterfaceId	1.3.6.1.4.1.3715.17.2.4.1.1	INTEGER	read-only	Unique interface Id within the module (e.g. RF connector number).
U32 sciObjectId	1.3.6.1.4.1.3715.17.2.4.1.2	Unsigned32	read-only	Unique identifier of the monitorable object within the interface.
INT sciObjectValue	1.3.6.1.4.1.3715.17.2.4.1.3	INTEGER	read-only	Value of the monitorable object. The sciObjectDescriptor tells name, scale and unit of the object.
STR sciObjectDescriptor	1.3.6.1.4.1.3715.17.2.4.1.4	DisplayString	read-only	Description of the monitorable object. See scdObjectDescriptor for format, example and usage.
INT sciObjectAlarmValue	1.3.6.1.4.1.3715.17.2.4.1.5	INTEGER	read-only	See dmObjectAlarmValue for format, example and usage.
statusCodeTransportStreamTable	1.3.6.1.4.1.3715.17.2.5		not-accessible	This table describes monitorable objects of each transport stream. The objects may represents real objects or classes. The monitoring system or user shall not poll this table to detect device state. Instead - user shall wait for traps or poll currentAlarmTable(1.3.6.1.4.1.5591.1.1.2) from SCTE-HMS-PROPERTY-MIB. In this case statusCodeTransportStreamTable shall be used to obtains text definition of alarm.
statusCodeTransportStreamEntry	1.3.6.1.4.1.3715.17.2.5.1		not-accessible
INT sctsTransportStreamId	1.3.6.1.4.1.3715.17.2.5.1.1	INTEGER	read-only	Unique transport stream id inside the interface.
U32 sctsObjectId	1.3.6.1.4.1.3715.17.2.5.1.2	Unsigned32	read-only	Unique identifier of the monitorable object.
INT sctsObjectValue	1.3.6.1.4.1.3715.17.2.5.1.3	INTEGER	read-only	Value of the monitorable object. The sctsObjectDescriptor tells name, scale and unit of the object.
STR sctsObjectDescriptor	1.3.6.1.4.1.3715.17.2.5.1.4	DisplayString	read-only	Description of the monitorable object. See dmObjectDescriptor for format, example and usage.
INT sctsObjectAlarmValue	1.3.6.1.4.1.3715.17.2.5.1.5	INTEGER	read-only	See scdObjectAlarmValue for format, example and usage.
statusCodeServiceTable	1.3.6.1.4.1.3715.17.2.6		not-accessible	This table describes monitorable objects of each service. The objects may represents real objects or classes. The monitoring system or user shall not poll this table to detect device state. Instead - user shall wait for traps or poll currentAlarmTable(1.3.6.1.4.1.5591.1.1.2) from SCTE-HMS-PROPERTY-MIB. In this case statusCodeServiceTable shall be used to obtains text definition of alarm.
statusCodeServiceEntry	1.3.6.1.4.1.3715.17.2.6.1		not-accessible
INT scsSID	1.3.6.1.4.1.3715.17.2.6.1.1	INTEGER	read-only	Unique service id number inside the transport stream.
U32 scsObjectId	1.3.6.1.4.1.3715.17.2.6.1.2	Unsigned32	read-only	Unique identifier of the monitorable object.
INT scsObjectValue	1.3.6.1.4.1.3715.17.2.6.1.3	INTEGER	read-only	Value of the monitorable object. The scsObjectDescriptor tells name, scale and unit of the object.
STR scsObjectDescriptor	1.3.6.1.4.1.3715.17.2.6.1.4	DisplayString	read-only	Description of the monitorable object. See scdObjectDescriptor for format, example and usage.
STR scsServiceName	1.3.6.1.4.1.3715.17.2.6.1.5	DisplayString	read-only	The name of the service.
INT scsObjectAlarmValue	1.3.6.1.4.1.3715.17.2.6.1.6	INTEGER	read-only	See scdObjectAlarmValue for format, example and usage.
statusCodePidTable	1.3.6.1.4.1.3715.17.2.7		not-accessible	This table lists monitorable objects of each PID. The objects may represents real objects or classes. The monitoring system or user shall not poll this table to detect device state. Instead - user shall wait for traps or poll currentAlarmTable(1.3.6.1.4.1.5591.1.1.2) from SCTE-HMS-PROPERTY-MIB. In this case statusCodePidTable shall be used to obtains text definition of alarm.
statusCodePidEntry	1.3.6.1.4.1.3715.17.2.7.1		not-accessible
INT scpPID	1.3.6.1.4.1.3715.17.2.7.1.1	INTEGER	read-only	Unique PID value inside the transport stream.
U32 scpObjectId	1.3.6.1.4.1.3715.17.2.7.1.2	Unsigned32	read-only	Unique identifier of the monitorable object.
INT scpObjectValue	1.3.6.1.4.1.3715.17.2.7.1.3	INTEGER	read-only	Value of the monitorable object. The scpObjectDescriptor tells name, scale and unit of the object.
STR scpObjectDescriptor	1.3.6.1.4.1.3715.17.2.7.1.4	DisplayString	read-only	Description of the monitorable object. See scdObjectDescriptor for format, example and usage.
INT scpObjectAlarmValue	1.3.6.1.4.1.3715.17.2.7.1.5	INTEGER	read-only	See scdObjectAlarmValue for format, example and usage.
interface	1.3.6.1.4.1.3715.17.3
ifExtTable	1.3.6.1.4.1.3715.17.3.1		not-accessible
ifExtEntry	1.3.6.1.4.1.3715.17.3.1.1		not-accessible
INT ifExtIndex	1.3.6.1.4.1.3715.17.3.1.1.1	INTEGER	not-accessible	A unique index for an interface. The index is of following format: SDPPVVVV, where: - S = Slot number - D = input(1) / output(2) - PP = Physical interface number - VVVV = Virtual interface number
STR ifExtName	1.3.6.1.4.1.3715.17.3.1.1.2	DisplayString	read-only	Description for the interface.
INT ifExtModule	1.3.6.1.4.1.3715.17.3.1.1.3	INTEGER	read-only	Number of the physical module or slot housing the interface.
INT ifExtPhysInterface	1.3.6.1.4.1.3715.17.3.1.1.4	INTEGER	read-only	Physical interface number.
INT ifExtLogiInterface	1.3.6.1.4.1.3715.17.3.1.1.5	INTEGER	read-only	Logical interface number.
INT ifExtDirection	1.3.6.1.4.1.3715.17.3.1.1.6	INTEGER	read-only	Direction for the data going through the interface.
signalPhysTable	1.3.6.1.4.1.3715.17.3.2		not-accessible
signalPhysEntry	1.3.6.1.4.1.3715.17.3.2.1		not-accessible
INT signalSnr	1.3.6.1.4.1.3715.17.3.2.1.2	INTEGER	read-only	Recent signal to noise ratio in 1/10th of dB.
INT signalSnrMin	1.3.6.1.4.1.3715.17.3.2.1.3	INTEGER	read-write	Lowest measured SNR value since last device startup or last counter reset.
INT signalSnrMax	1.3.6.1.4.1.3715.17.3.2.1.4	INTEGER	read-write	Highest measured SNR value since last device startup or last counter reset.
INT signalCcErrors	1.3.6.1.4.1.3715.17.3.2.1.5	INTEGER	read-write	The number of continuity errors since last device startup or last counter reset.
FLO signalBer	1.3.6.1.4.1.3715.17.3.2.1.6	Float	read-only	Calculated bit error ratio of the signal.
FLO signalVber	1.3.6.1.4.1.3715.17.3.2.1.7	Float	read-only	Calculated Viterbi bit error ratio of the signal.
transferTable	1.3.6.1.4.1.3715.17.3.3		not-accessible
transferEntry	1.3.6.1.4.1.3715.17.3.3.1		not-accessible
INT transBitrate	1.3.6.1.4.1.3715.17.3.3.1.2	INTEGER	read-only	Recent measured bitrate of the interface in kilobits per second.
INT transBitrateMin	1.3.6.1.4.1.3715.17.3.3.1.3	INTEGER	read-write	Lowest measured bitrate since last device startup or last counter reset. Writing clears the counter.
INT transBitrateMax	1.3.6.1.4.1.3715.17.3.3.1.4	INTEGER	read-write	Highest measured bitrate since last device startup or last counter reset. Writing clears the counter.
proMpegFecTable	1.3.6.1.4.1.3715.17.3.20		not-accessible
proMpegFecEntry	1.3.6.1.4.1.3715.17.3.20.1		not-accessible
C32 fecValidPkts	1.3.6.1.4.1.3715.17.3.20.1.1	Counter32	read-write	Number of media stream packets received. Writing any value in this oid will clear all ProMpegFec related counters on the current interface.
C32 fecUncorrectedPkts	1.3.6.1.4.1.3715.17.3.20.1.2	Counter32	read-write	Number of missing media stream packets after FEC decoding. Writing any value in this oid will clear all ProMpegFec related counters on the current interface.
C32 fecCorrectedPkts	1.3.6.1.4.1.3715.17.3.20.1.3	Counter32	read-write	Number of corrected packets after FEC decoding. Writing any value in this oid will clear all ProMpegFec related counters on the current interface.
C32 fecDuplicatePkts	1.3.6.1.4.1.3715.17.3.20.1.4	Counter32	read-write	Number of duplicate packets received. Defined as a received packet with the same RTP sequence number as any of the packets already in the decoding buffer. All duplicate packets are automatically discarded and do not cause missing packets or duplicates to the output stream. Writing any value in this oid will clear all ProMpegFec related counters on the current interface.
C32 fecReorderedPkts	1.3.6.1.4.1.3715.17.3.20.1.5	Counter32	read-write	Number of reordered packets received. Defined as a received packet which RTP sequence number is smaller than the highest RTP sequence number already received, excluding duplicate packets and packets which are out of the decoding buffer range. These packets will be re-ordered and do not cause missing packets to the output stream. Writing any value in this oid will clear all ProMpegFec related counters on the current interface.
C32 fecIncorrectSeqNumbers	1.3.6.1.4.1.3715.17.3.20.1.6	Counter32	read-write	Number of received media packets that have RTP sequence number out of decoding buffer range. All these packet are discarded. If 10 consecutive packets are out of range then decoding buffer is flushed and re-initialised i.e. all packets in the buffer are discarded. Incorrect sequence numbers counter will not be incremented if decoding buffer has been flushed. Writing any value in this oid will clear all ProMpegFec related counters on the current interface.
C32 fecDiscontinuities	1.3.6.1.4.1.3715.17.3.20.1.7	Counter32	read-write	Number of RTP sequence number discontinuities after FEC decoding. Discontinuity is detected when the sequence number of received RTP packet (after decoding) is not equal to sequence number of previous packet. Discontinuities are typically detected when there are uncorrected packets in the stream, or when there are brief interruptions in the stream (in range of about 1-20 seconds). Also abrupt change of stream source will be counted as discontinuity because of jump in RTP sequence numbers. Writing any value in this oid will clear all ProMpegFec related counters on the current interface.
notifications	1.3.6.1.4.1.3715.17.4
statusFlags	1.3.6.1.4.1.3715.17.5
moduleStatusTable	1.3.6.1.4.1.3715.17.5.2		not-accessible
moduleStatusEntry	1.3.6.1.4.1.3715.17.5.2.1		not-accessible
INT moduleId	1.3.6.1.4.1.3715.17.5.2.1.1	INTEGER	not-accessible	Module identifier
INT modulePidConflictStatus	1.3.6.1.4.1.3715.17.5.2.1.4	INTEGER	read-only	PID conflict status
INT moduleTemperatureHigh	1.3.6.1.4.1.3715.17.5.2.1.6	INTEGER	read-only	High temperature status
INT moduleTemperatureLow	1.3.6.1.4.1.3715.17.5.2.1.7	INTEGER	read-only	Low temperature status
INT modulePidCapaStatus	1.3.6.1.4.1.3715.17.5.2.1.4104	INTEGER	read-only	Module PID capacity status
INT modulePsisiCaptureCapaStatus	1.3.6.1.4.1.3715.17.5.2.1.4105	INTEGER	read-only	Module PSI/SI table capture capacity status
INT moduleSidAllocStatus	1.3.6.1.4.1.3715.17.5.2.1.4106	INTEGER	read-only	Module service ID allocation capacity status
INT moduleCaDetectStatus	1.3.6.1.4.1.3715.17.5.2.1.4108	INTEGER	read-only	CA module detection status
INT moduleDetectStatus	1.3.6.1.4.1.3715.17.5.2.1.4111	INTEGER	read-only	Module detection status
INT moduleVoltageHigh	1.3.6.1.4.1.3715.17.5.2.1.4112	INTEGER	read-only	High voltage status
INT moduleVoltageLow	1.3.6.1.4.1.3715.17.5.2.1.4113	INTEGER	read-only	Low voltage status
INT moduleCurrentHigh	1.3.6.1.4.1.3715.17.5.2.1.4114	INTEGER	read-only	High current status
INT moduleCurrentLow	1.3.6.1.4.1.3715.17.5.2.1.4115	INTEGER	read-only	Low current status
INT moduleDaemonInitStatus	1.3.6.1.4.1.3715.17.5.2.1.4127	INTEGER	read-only	Module daemon initialization status
INT moduleDriverStatus	1.3.6.1.4.1.3715.17.5.2.1.4129	INTEGER	read-only	Module device driver status
INT moduleHwStatus	1.3.6.1.4.1.3715.17.5.2.1.4130	INTEGER	read-only	Module hardware status
INT moduleFanStatus	1.3.6.1.4.1.3715.17.5.2.1.4131	INTEGER	read-only	Fan status
INT modulePowerSourceStatus	1.3.6.1.4.1.3715.17.5.2.1.4132	INTEGER	read-only	Power source status
INT modulePsuOverloadStatus	1.3.6.1.4.1.3715.17.5.2.1.4133	INTEGER	read-only	Power supply overload status
INT moduleBootupProgressStatus	1.3.6.1.4.1.3715.17.5.2.1.4134	INTEGER	read-only	Module bootup progress
INT moduleBootupRetryStatus	1.3.6.1.4.1.3715.17.5.2.1.4135	INTEGER	read-only	Module bootup retry status
INT moduleBootupStatus	1.3.6.1.4.1.3715.17.5.2.1.4136	INTEGER	read-only	Module bootup status
INT moduleShutdownProgressStatus	1.3.6.1.4.1.3715.17.5.2.1.4137	INTEGER	read-only	Module shutdown progress
INT moduleConnStatus	1.3.6.1.4.1.3715.17.5.2.1.4138	INTEGER	read-only	Module connection status
INT moduleCompatStatus	1.3.6.1.4.1.3715.17.5.2.1.4139	INTEGER	read-only	Module compatibility status
INT moduleUpcPowerLow	1.3.6.1.4.1.3715.17.5.2.1.4147	INTEGER	read-only	Module UPC input power low status
INT moduleUpcPowerHigh	1.3.6.1.4.1.3715.17.5.2.1.4148	INTEGER	read-only	Module UPC input power high status
INT moduleCalibrDataStatus	1.3.6.1.4.1.3715.17.5.2.1.4149	INTEGER	read-only	Module calibration data status
INT moduleCalibrDataCheckStatus	1.3.6.1.4.1.3715.17.5.2.1.4150	INTEGER	read-only	Module calibration data check status
INT moduleDescrStatus	1.3.6.1.4.1.3715.17.5.2.1.4151	INTEGER	read-only	Module descrambling status
INT moduleBackupStatus	1.3.6.1.4.1.3715.17.5.2.1.4153	INTEGER	read-only	Module backup status
INT moduleNitOutputsStatus	1.3.6.1.4.1.3715.17.5.2.1.4154	INTEGER	read-only	Supported Nit output module status
INT moduleNitSelectionStatus	1.3.6.1.4.1.3715.17.5.2.1.4155	INTEGER	read-only	Nit output selection status
INT moduleNitConfChangeStatus	1.3.6.1.4.1.3715.17.5.2.1.4156	INTEGER	read-only	Nit configuration change status
INT moduleNitDataQueryStatus	1.3.6.1.4.1.3715.17.5.2.1.4157	INTEGER	read-only	Nit data query status
INT moduleNitWizardStatus	1.3.6.1.4.1.3715.17.5.2.1.4158	INTEGER	read-only	Nit wizard status
INT moduleQamFreqStatus	1.3.6.1.4.1.3715.17.5.2.1.4159	INTEGER	read-only	QAM output unique frequency status
INT moduleOutputSidStatus	1.3.6.1.4.1.3715.17.5.2.1.4173	INTEGER	read-only	Module output SID status
INT moduleConfStatus	1.3.6.1.4.1.3715.17.5.2.1.4175	INTEGER	read-only	Module configuration status
INT moduleFreqStatus	1.3.6.1.4.1.3715.17.5.2.1.4176	INTEGER	read-only	Module frequency configuration range status
INT moduleOutputPowerStatus	1.3.6.1.4.1.3715.17.5.2.1.4177	INTEGER	read-only	Module output power status
INT moduleSymrateStatus	1.3.6.1.4.1.3715.17.5.2.1.4178	INTEGER	read-only	Module symbol rate configuration status
INT moduleChanDistStatus	1.3.6.1.4.1.3715.17.5.2.1.4179	INTEGER	read-only	Module channel distance configuration status
INT moduleLnbVoltStatus	1.3.6.1.4.1.3715.17.5.2.1.4180	INTEGER	read-only	Module LNB voltage configuration status
INT moduleFecRateStatus	1.3.6.1.4.1.3715.17.5.2.1.4181	INTEGER	read-only	Module FEC rate configuration vs modulation status
INT moduleLnbCurrStatus	1.3.6.1.4.1.3715.17.5.2.1.4182	INTEGER	read-only	Module LNB current status
INT moduleFreqOffsetStatus	1.3.6.1.4.1.3715.17.5.2.1.4183	INTEGER	read-only	Module frequency offset configuration status
INT moduleDescrRestartStatus	1.3.6.1.4.1.3715.17.5.2.1.4185	INTEGER	read-only	Module descrambling restart status
INT moduleCamRestartStatus	1.3.6.1.4.1.3715.17.5.2.1.4186	INTEGER	read-only	Module CAM restart status
INT moduleEcmgStatus	1.3.6.1.4.1.3715.17.5.2.1.4187	INTEGER	read-only	Ecmg status
INT moduleEcmStreamStatus	1.3.6.1.4.1.3715.17.5.2.1.4188	INTEGER	read-only	Ecm stream status
INT moduleEmmStatus	1.3.6.1.4.1.3715.17.5.2.1.4189	INTEGER	read-only	Emm status
INT moduleEmmStreamStatus	1.3.6.1.4.1.3715.17.5.2.1.4190	INTEGER	read-only	Emm stream status
INT moduleEcmgConnStatus	1.3.6.1.4.1.3715.17.5.2.1.4191	INTEGER	read-only	Ecmg connection status
INT moduleEmmConnStatus	1.3.6.1.4.1.3715.17.5.2.1.4192	INTEGER	read-only	Emm connection status
INT moduleEcmgSpareStatus	1.3.6.1.4.1.3715.17.5.2.1.4194	INTEGER	read-only	Ecmg spare connection status
INT moduleBootloaderAvailStatus	1.3.6.1.4.1.3715.17.5.2.1.4195	INTEGER	read-only	Module bootloader availability status
INT moduleBl1UpdateProgStatus	1.3.6.1.4.1.3715.17.5.2.1.4196	INTEGER	read-only	Module bootloader update progress
INT moduleBl2UpdateProgStatus	1.3.6.1.4.1.3715.17.5.2.1.4197	INTEGER	read-only	Module bootloader update progress
INT moduleBl1UpdateStatus	1.3.6.1.4.1.3715.17.5.2.1.4198	INTEGER	read-only	Module bootloader update status
INT moduleBl2UpdateStatus	1.3.6.1.4.1.3715.17.5.2.1.4199	INTEGER	read-only	Module bootloader update status
INT moduleActiveBackupStatus	1.3.6.1.4.1.3715.17.5.2.1.4203	INTEGER	read-only	Backup module status
INT moduleConfProgressStatus	1.3.6.1.4.1.3715.17.5.2.1.4205	INTEGER	read-only	Module configuration progress
INT modulePresenceStatus	1.3.6.1.4.1.3715.17.5.2.1.4206	INTEGER	read-only	Module presence progress
INT moduleProcessRestartStatus	1.3.6.1.4.1.3715.17.5.2.1.4208	INTEGER	read-only	Process restart status
INT moduleBackupLicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4209	INTEGER	read-only	Backup license status
INT modulePsisiEditorLicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4210	INTEGER	read-only	PSI/SI editor license status
INT moduleMuxLicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4211	INTEGER	read-only	Multiplexing license status
INT moduleDemuxLicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4212	INTEGER	read-only	Demultiplexing license status
INT moduleDvbLicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4213	INTEGER	read-only	DVB processing license status
INT moduleMsdLicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4214	INTEGER	read-only	MSD license status
INT moduleDvbs2LicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4215	INTEGER	read-only	DVB-S2 processing license status
INT moduleDvbt2LicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4216	INTEGER	read-only	DVB-T2 processing license status
INT moduleScsLicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4217	INTEGER	read-only	Scs license status
INT moduleCliLoginStatus	1.3.6.1.4.1.3715.17.5.2.1.4218	INTEGER	read-only	CLI login status
INT moduleRedunActivationStatus	1.3.6.1.4.1.3715.17.5.2.1.4222	INTEGER	read-only	Redundancy activation status
INT moduleExtioPinSignalingStatus	1.3.6.1.4.1.3715.17.5.2.1.4223	INTEGER	read-only	EXT-IO pin status
INT moduleBackupPsuStatus	1.3.6.1.4.1.3715.17.5.2.1.4224	INTEGER	read-only	Backup power supply status
INT moduleIntrusionStatus	1.3.6.1.4.1.3715.17.5.2.1.4225	INTEGER	read-only	Intrusion detection status
INT moduleRedunStatus	1.3.6.1.4.1.3715.17.5.2.1.4227	INTEGER	read-only	Redundancy status
INT moduleBackupHwStatus	1.3.6.1.4.1.3715.17.5.2.1.4230	INTEGER	read-only	Hardware backup support status
INT moduleSwUpdateProgress	1.3.6.1.4.1.3715.17.5.2.1.4231	INTEGER	read-only	Software update progress
INT moduleSwUpdateStatus	1.3.6.1.4.1.3715.17.5.2.1.4233	INTEGER	read-only	Software update status
INT moduleEitLicenseStatus	1.3.6.1.4.1.3715.17.5.2.1.4235	INTEGER	read-only	EIT license status
INT moduleDescramblingStatus	1.3.6.1.4.1.3715.17.5.2.1.4237	INTEGER	read-only	Descrambling status
INT moduleDvbTimeStatus	1.3.6.1.4.1.3715.17.5.2.1.4243	INTEGER	read-only	DVB time detection status
INT moduleTunerDcFeedStatus	1.3.6.1.4.1.3715.17.5.2.1.4245	INTEGER	read-only	Tuner DC feed current status
INT moduleTunerPlpSelectionReqStatus	1.3.6.1.4.1.3715.17.5.2.1.4247	INTEGER	read-only	Tuner data PLP ID requirement status
INT moduleTunerPlpStatus	1.3.6.1.4.1.3715.17.5.2.1.4248	INTEGER	read-only	Tuner data PLP ID validity status
INT moduleTunerHierarchyStatus	1.3.6.1.4.1.3715.17.5.2.1.4249	INTEGER	read-only	Status of transmission hierarchy
INT moduleEcmStatus	1.3.6.1.4.1.3715.17.5.2.1.4250	INTEGER	read-only	ECM stream connection status
INT moduleScramConflictStatus	1.3.6.1.4.1.3715.17.5.2.1.4251	INTEGER	read-only	Module scrambling shared component conflict status
INT moduleScramSharedStatus	1.3.6.1.4.1.3715.17.5.2.1.4252	INTEGER	read-only	Module scrambling shared component status
INT moduleBackupVoltageHigh	1.3.6.1.4.1.3715.17.5.2.1.4253	INTEGER	read-only	Backup high voltage status
INT moduleBackupVoltageLow	1.3.6.1.4.1.3715.17.5.2.1.4254	INTEGER	read-only	Backup low voltage status
INT moduleSdtTableStatus	1.3.6.1.4.1.3715.17.5.2.1.4255	INTEGER	read-only	Sdt table template status
INT moduleDescramblingRestart	1.3.6.1.4.1.3715.17.5.2.1.4256	INTEGER	read-only	Descrambling restart status
INT moduleCaModuleRestart	1.3.6.1.4.1.3715.17.5.2.1.4257	INTEGER	read-only	CA module restart status
INT moduleCaMenuStatus	1.3.6.1.4.1.3715.17.5.2.1.4258	INTEGER	read-only	CA menu access status
INT moduleInvalidCamRouting	1.3.6.1.4.1.3715.17.5.2.1.4259	INTEGER	read-only	CAM routing status
INT moduleNitSidConflict	1.3.6.1.4.1.3715.17.5.2.1.4260	INTEGER	read-only	Nit / Sid conflict status
INT moduleLicenseMissingFEC	1.3.6.1.4.1.3715.17.5.2.1.4262	INTEGER	read-only	FEC license status
INT moduleFecCorrectionStatus	1.3.6.1.4.1.3715.17.5.2.1.4263	INTEGER	read-only	Fec packet correction status. Correction overload (2) is result of too many simultaneous missing packets.
INT moduleFecPacketDropStatus	1.3.6.1.4.1.3715.17.5.2.1.4264	INTEGER	read-only	FEC packet discarding status. Packet discarding (2) is resulted by too high bitrate.
INT moduleFecMediaPktsStatus	1.3.6.1.4.1.3715.17.5.2.1.4265	INTEGER	read-only	Fec media packet discarding status. Packet discarding (2) is resulted by too high bitrate.
INT moduleSfpLinkStatus	1.3.6.1.4.1.3715.17.5.2.1.4269	INTEGER	read-only	SFP link status
INT moduleBackupSyncModeOff	1.3.6.1.4.1.3715.17.5.2.1.4272	INTEGER	read-only	Backup sync mode off status flag
INT moduleBackupSyncModeManual	1.3.6.1.4.1.3715.17.5.2.1.4273	INTEGER	read-only	Backup sync mode manual status flag
INT moduleBackupSyncModeAuto	1.3.6.1.4.1.3715.17.5.2.1.4274	INTEGER	read-only	Backup sync mode automatic status flag
INT moduleBackupSyncConfStatus	1.3.6.1.4.1.3715.17.5.2.1.4275	INTEGER	read-only	Backup sync configuration change status
INT moduleBackupSyncStatus	1.3.6.1.4.1.3715.17.5.2.1.4276	INTEGER	read-only	Backup configuration synchronization status
INT moduleBackupSyncSwCompatibility	1.3.6.1.4.1.3715.17.5.2.1.4278	INTEGER	read-only	Software version compatibility for backup sync
INT moduleBackupSyncHwCompatibility	1.3.6.1.4.1.3715.17.5.2.1.4279	INTEGER	read-only	Hardware version compatibility for backup sync
INT moduleBackupSyncConfFaultStatus	1.3.6.1.4.1.3715.17.5.2.1.4280	INTEGER	read-only	Backup sync configuration fault status
INT moduleBackupSyncConnectionStatus	1.3.6.1.4.1.3715.17.5.2.1.4281	INTEGER	read-only	Backup sync connection status
INT moduleBackupSyncFromBackupStatus	1.3.6.1.4.1.3715.17.5.2.1.4283	INTEGER	read-only	Status flag for backup autosync from backup to main
INT moduleBackupSyncRebootStatus	1.3.6.1.4.1.3715.17.5.2.1.4284	INTEGER	read-only	Status flag for rebooting pair device to new configuration
INT moduleBackupSyncLicenseCompatStatus	1.3.6.1.4.1.3715.17.5.2.1.4285	INTEGER	read-only	License compatibility status flag for backup sync
INT moduleBackupSyncLicenseCompareStatus	1.3.6.1.4.1.3715.17.5.2.1.4286	INTEGER	read-only	Backup sync license comparing status
INT moduleDeviceFirstBootStatus	1.3.6.1.4.1.3715.17.5.2.1.4288	INTEGER	read-only	Status flag for device first boot operations
INT modulePartitionConfigurationBackup	1.3.6.1.4.1.3715.17.5.2.1.4289	INTEGER	read-only	Status flag for partition configuration backup operation
INT modulePartitionConfigurationRestore	1.3.6.1.4.1.3715.17.5.2.1.4290	INTEGER	read-only	Status flag for partition configuration restore operation
INT moduleSwRevertStatus	1.3.6.1.4.1.3715.17.5.2.1.4291	INTEGER	read-only	Software revertion status
INT moduleMaxOutputPidsStatus	1.3.6.1.4.1.3715.17.5.2.1.4292	INTEGER	read-only	Status flag for maximum number of Pid allocations
INT moduleUserRebootStatus	1.3.6.1.4.1.3715.17.5.2.1.4293	INTEGER	read-only	Status flag for user initiated reboot
INT moduleRemovalStatus	1.3.6.1.4.1.3715.17.5.2.1.4294	INTEGER	read-only	Status flag for module removal
INT moduleInsertionStatus	1.3.6.1.4.1.3715.17.5.2.1.4295	INTEGER	read-only	Status flag for module insertion
INT moduleSptsInputConfStatus	1.3.6.1.4.1.3715.17.5.2.1.4296	INTEGER	read-only	Status flag for input spts misconfiguration
ifStatusTable	1.3.6.1.4.1.3715.17.5.3		not-accessible
ifStatusEntry	1.3.6.1.4.1.3715.17.5.3.1		not-accessible
INT ifId	1.3.6.1.4.1.3715.17.5.3.1.1	INTEGER	not-accessible	Interface identifier
INT ifDirection	1.3.6.1.4.1.3715.17.5.3.1.2	INTEGER	not-accessible	Interface data direction
INT ifSignalStatus	1.3.6.1.4.1.3715.17.5.3.1.4097	INTEGER	read-only	Interface signal status
INT ifAsiLinkStatus	1.3.6.1.4.1.3715.17.5.3.1.4102	INTEGER	read-only	ASI link status
INT ifLinkStatus	1.3.6.1.4.1.3715.17.5.3.1.4226	INTEGER	read-only	Interface link status
tsStatusTable	1.3.6.1.4.1.3715.17.5.4		not-accessible
tsStatusEntry	1.3.6.1.4.1.3715.17.5.4.1		not-accessible
INT tsPidRemappingStatus	1.3.6.1.4.1.3715.17.5.4.1.5	INTEGER	read-only	TS PID remapping status
INT tsManualTableInsertStatus	1.3.6.1.4.1.3715.17.5.4.1.8	INTEGER	read-only	TS manual table insertion status
INT tsPassthruDupStatus	1.3.6.1.4.1.3715.17.5.4.1.11	INTEGER	read-only	TS output service passthrough duplication status
INT tsSyncStatus	1.3.6.1.4.1.3715.17.5.4.1.4098	INTEGER	read-only	TS sync status
INT tsRxStatus	1.3.6.1.4.1.3715.17.5.4.1.4099	INTEGER	read-only	TS Rx error status
INT tsInputBufferStatus	1.3.6.1.4.1.3715.17.5.4.1.4100	INTEGER	read-only	TS input buffer status
INT tsNetworkStatus	1.3.6.1.4.1.3715.17.5.4.1.4103	INTEGER	read-only	TS network ID status
INT tsPsisiCapaStatus	1.3.6.1.4.1.3715.17.5.4.1.4109	INTEGER	read-only	TS PSI/SI insertion capacity status
INT tsMultiplexDiscardStatus	1.3.6.1.4.1.3715.17.5.4.1.4110	INTEGER	read-only	TS multiplex packet discard status
INT tsMultiplexDelayStatus	1.3.6.1.4.1.3715.17.5.4.1.4228	INTEGER	read-only	TS multiplex packet delay status
INT tsCbrOversubscriptionStatus	1.3.6.1.4.1.3715.17.5.4.1.4229	INTEGER	read-only	TS CBR oversubscription status
INT tsCbrDiscardStatus	1.3.6.1.4.1.3715.17.5.4.1.4236	INTEGER	read-only	TS CBR packet discard due to oversubscription status
INT tsIpInputCapaStatus	1.3.6.1.4.1.3715.17.5.4.1.4238	INTEGER	read-only	TS IP input capacity status
INT tsEitReinsertCapaStatus	1.3.6.1.4.1.3715.17.5.4.1.4239	INTEGER	read-only	TS EIT reinsert capacity status
INT tsSectionCapaStatus	1.3.6.1.4.1.3715.17.5.4.1.4240	INTEGER	read-only	TS section processing capacity status
INT tsRtpInputStatus	1.3.6.1.4.1.3715.17.5.4.1.4241	INTEGER	read-only	TS RTP input packet droip status
INT tsRtpSeqStatus	1.3.6.1.4.1.3715.17.5.4.1.4242	INTEGER	read-only	TS RTP input packet sequence anomaly status
INT tsTdtTotGenStatus	1.3.6.1.4.1.3715.17.5.4.1.4246	INTEGER	read-only	TS output TDT/TOT table generation status
INT tsSttGenStatus	1.3.6.1.4.1.3715.17.5.4.1.4261	INTEGER	read-only	TS output STT table generation status
INT tsFecPacketCorrectionStatus	1.3.6.1.4.1.3715.17.5.4.1.4266	INTEGER	read-only	Status flag for FEC correcting packets
INT tsFecInputAnomalyStatus	1.3.6.1.4.1.3715.17.5.4.1.4267	INTEGER	read-only	Status flag for FEC input anomaly detection
INT tsFecCorrectionCapacityStatus	1.3.6.1.4.1.3715.17.5.4.1.4268	INTEGER	read-only	Fec input packets correction capacity status
INT tsIpMirrorOutputPacketLossStatus	1.3.6.1.4.1.3715.17.5.4.1.4297	INTEGER	read-only	Status flag for IP mirror output packet discarding
serviceStatusTable	1.3.6.1.4.1.3715.17.5.5		not-accessible
serviceStatusEntry	1.3.6.1.4.1.3715.17.5.5.1		not-accessible
INT serviceId	1.3.6.1.4.1.3715.17.5.5.1.1	INTEGER	not-accessible	Service identifier
INT serviceStatus	1.3.6.1.4.1.3715.17.5.5.1.3	INTEGER	read-only	Service status
pidStatusTable	1.3.6.1.4.1.3715.17.5.6		not-accessible
pidStatusEntry	1.3.6.1.4.1.3715.17.5.6.1		not-accessible
INT pId	1.3.6.1.4.1.3715.17.5.6.1.1	INTEGER	not-accessible	Program Identifier
INT pidStatus	1.3.6.1.4.1.3715.17.5.6.1.2	INTEGER	read-only	PID status

RFC description

Teleste Luminato optical monitoring device management for status reporting, alarms, and general device identification.

Start monitoring Teleste optical nodes with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TELESTE-LUMINATO-MIB

What Is TELESTE-LUMINATO-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description