TELDAT-TRAP-SDLC-MIB

All MIBs › TELDAT-TRAP-SDLC-MIB

Organization: Teldat, S.A.

Last Updated: 2014-01-20

Category: Remote Access and Serial WAN, Teldat Router Management, Teldat Trap Notifications

Description: Defines Teldat router SDLC (Synchronous Data Link Control) event trap notifications.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TELDAT-TRAP-SDLC-MIB?

TELDAT-TRAP-SDLC-MIB is a vendor-specific SNMP module from Teldat, a Spanish manufacturer of enterprise routers, and it is dedicated entirely to notifications generated by the router's SDLC (Synchronous Data Link Control) subsystem, a legacy IBM mainframe link protocol still bridged over some WAN routers. Rather than exposing polled counters, it defines a set of trap objects (per-line variables such as interface identifier, station address, status, and frame count) that are bundled into notification PDUs when an SDLC event occurs. In monitoring terms this is fault/event-oriented rather than resource-oriented: it lets an operator learn in near real time when a particular SDLC line or station changes interface state, address, or status, functioning as an early-warning mechanism for link-level SDLC failures rather than a source of hardware health metrics like temperature or CPU. It depends on the base TELDAT enterprise MIB tree and standard SNMPv2 notification conventions (NOTIFICATION-TYPE) for its trap definitions. It is typically deployed on Teldat routers that still terminate legacy SDLC/mainframe links inside otherwise modern WAN environments, feeding an NMS trap receiver for legacy-protocol fault alerting, and administrators supporting these routers typically start with a TELDAT-TRAP-SDLC-MIB download to load its trap definitions into their NMS.

IPNetwork Monitor allows you to monitor SNMP objects defined in TELDAT-TRAP-SDLC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Teldat WAN router
Teldat router with legacy SDLC/SNA interface module

Monitoring Examples

A network operations team would configure their trap receiver to catch notifications carrying objects like sdlc7-status and sdlc7-interface, alerting them the instant SDLC line 7 transitions to a fault or disconnect state. Fields such as sdlc2-address and sdlc8-count let the operator correlate which SDLC station address and frame count were active at the moment of the event, aiding root-cause diagnosis of a flapping legacy link. Because the MIB is trap-only, there is no polling table to walk; monitoring value comes entirely from subscribing to sdlcNotifications and inspecting the bound variables in each received trap.

What Can Be Monitored

SDLC interface identifier per event
SDLC station address
SDLC line/interface status changes
SDLC frame/event count
SDLC subsystem trap notifications

Imported Objects

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString

From TELDAT-MIB

telEventTraps

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
sdlcTrapsMIB	1.3.6.1.4.1.2007.1.4.90			This Module Information Base file is defined for managing received SNMP notifications generated by the SDLC event subsystem.
sdlcEventsGroup	1.3.6.1.4.1.2007.1.4.90.1
sdlcEventObjects1	1.3.6.1.4.1.2007.1.4.90.1.1			Event SDLC.1 DLSw SDLC has been initialized for operation over the serial device and is now available for use in the router.
STR sdlc1_interface	1.3.6.1.4.1.2007.1.4.90.1.1.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.1
sdlcEventObjects2	1.3.6.1.4.1.2007.1.4.90.1.2			Event SDLC.2 An open was attempted on an SDLC station, but a configuration record was not defined via the ADD STATION command. The station will be opened using default configuration value. This station will be listed in the monitor process LIST STATION ALL command. An asterisk * next to the station address signifies that a default configuration is in use.
I32 sdlc2_address	1.3.6.1.4.1.2007.1.4.90.1.2.1	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.2
STR sdlc2_interface	1.3.6.1.4.1.2007.1.4.90.1.2.2	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.2
sdlcEventObjects3	1.3.6.1.4.1.2007.1.4.90.1.3			Event SDLC.3 There is currently no memory available to copy user data to SDLC. Another attempt will be made at a later time.
STR sdlc3_interface	1.3.6.1.4.1.2007.1.4.90.1.3.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.3
sdlcEventObjects4	1.3.6.1.4.1.2007.1.4.90.1.4			Event SDLC.4 A frame was received on an interface that is not yet owned by an SDLC client. All packets received are dropped until an SDLC client opens the port for use.
STR sdlc4_interface	1.3.6.1.4.1.2007.1.4.90.1.4.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.4
sdlcEventObjects5	1.3.6.1.4.1.2007.1.4.90.1.5			Event SDLC.5 An incoming packet was dropped due to no SDLC receive credit or a temporary memory shortage.
STR sdlc5_interface	1.3.6.1.4.1.2007.1.4.90.1.5.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.5
sdlcEventObjects6	1.3.6.1.4.1.2007.1.4.90.1.6			Event SDLC.6 real-sdlc-in received a packet with I-ERR set.
STR sdlc6_interface	1.3.6.1.4.1.2007.1.4.90.1.6.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.6
sdlcEventObjects7	1.3.6.1.4.1.2007.1.4.90.1.7			Event SDLC.7 The call to netsend() failed while trying to send a frame from SDLC.
STR sdlc7_interface	1.3.6.1.4.1.2007.1.4.90.1.7.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.7
I32 sdlc7_status	1.3.6.1.4.1.2007.1.4.90.1.7.2	Integer32	accessible-for-notify	Parameter 'status' in event SDLC.7
sdlcEventObjects8	1.3.6.1.4.1.2007.1.4.90.1.8			Event SDLC.8 The router transmitted an SDLC frame. This is the entire frame, including the SDLC header. The router logs all transmitted SDLC frames with this message. To log only transmitted SDLC I-frames, use SDLC-53.
I32 sdlc8_count	1.3.6.1.4.1.2007.1.4.90.1.8.1	Integer32	accessible-for-notify	Parameter 'count' in event SDLC.8
I32 sdlc8_address	1.3.6.1.4.1.2007.1.4.90.1.8.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.8
STR sdlc8_interface	1.3.6.1.4.1.2007.1.4.90.1.8.3	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.8
STR sdlc8_octets	1.3.6.1.4.1.2007.1.4.90.1.8.4	DisplayString	accessible-for-notify	Parameter 'octets' in event SDLC.8
sdlcEventObjects9	1.3.6.1.4.1.2007.1.4.90.1.9			Event SDLC.9 The router received an SDLC frame. This is the entire frame, including the SDLC header. The router logs all received SDLC frames with this message. To log only received SDLC I-frames, use SDLC-52.
I32 sdlc9_count	1.3.6.1.4.1.2007.1.4.90.1.9.1	Integer32	accessible-for-notify	Parameter 'count' in event SDLC.9
I32 sdlc9_address	1.3.6.1.4.1.2007.1.4.90.1.9.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.9
STR sdlc9_interface	1.3.6.1.4.1.2007.1.4.90.1.9.3	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.9
STR sdlc9_octets	1.3.6.1.4.1.2007.1.4.90.1.9.4	DisplayString	accessible-for-notify	Parameter 'octets' in event SDLC.9
sdlcEventObjects10	1.3.6.1.4.1.2007.1.4.90.1.10			Event SDLC.10 An entity in the router has attached to the interface and can now use SDLC services.
STR sdlc10_interface	1.3.6.1.4.1.2007.1.4.90.1.10.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.10
sdlcEventObjects11	1.3.6.1.4.1.2007.1.4.90.1.11			Event SDLC.11 An entity in the router is no longer using SDLC services on this interface.
STR sdlc11_interface	1.3.6.1.4.1.2007.1.4.90.1.11.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.11
sdlcEventObjects12	1.3.6.1.4.1.2007.1.4.90.1.12			Event SDLC.12 An interface signal has changed state. Note: an unwieldy number of these messages will be generated when the interface is operating in half duplex mode.
STR sdlc12_exception	1.3.6.1.4.1.2007.1.4.90.1.12.1	DisplayString	accessible-for-notify	Parameter 'exception' in event SDLC.12
STR sdlc12_interface	1.3.6.1.4.1.2007.1.4.90.1.12.2	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.12
sdlcEventObjects13	1.3.6.1.4.1.2007.1.4.90.1.13			Event SDLC.13 The SDLC link is now operating in Normal Response Mode, meaning that a SDLC connection is now in progress.
I32 sdlc13_address	1.3.6.1.4.1.2007.1.4.90.1.13.1	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.13
STR sdlc13_interface	1.3.6.1.4.1.2007.1.4.90.1.13.2	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.13
sdlcEventObjects14	1.3.6.1.4.1.2007.1.4.90.1.14			Event SDLC.14 An attempt by the router to connect to a remote link station has been refused.
I32 sdlc14_address	1.3.6.1.4.1.2007.1.4.90.1.14.1	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.14
STR sdlc14_interface	1.3.6.1.4.1.2007.1.4.90.1.14.2	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.14
sdlcEventObjects15	1.3.6.1.4.1.2007.1.4.90.1.15			Event SDLC.15 The SDLC link is now operating in Normal Disconnect Mode, meaning that a SDLC connection has been terminated in an orderly fashion.
I32 sdlc15_address	1.3.6.1.4.1.2007.1.4.90.1.15.1	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.15
STR sdlc15_interface	1.3.6.1.4.1.2007.1.4.90.1.15.2	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.15
sdlcEventObjects16	1.3.6.1.4.1.2007.1.4.90.1.16			Event SDLC.16 The SDLC protocol has been initialized.
I32 sdlc16_address	1.3.6.1.4.1.2007.1.4.90.1.16.1	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.16
I32 sdlc16_exception	1.3.6.1.4.1.2007.1.4.90.1.16.2	Integer32	accessible-for-notify	Parameter 'exception' in event SDLC.16
STR sdlc16_interface	1.3.6.1.4.1.2007.1.4.90.1.16.3	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.16
sdlcEventObjects17	1.3.6.1.4.1.2007.1.4.90.1.17			Event SDLC.17 SDLC received a frame to the broadcast address on a multipoint line. The frame was dropped.
STR sdlc17_interface	1.3.6.1.4.1.2007.1.4.90.1.17.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.17
sdlcEventObjects18	1.3.6.1.4.1.2007.1.4.90.1.18			Event SDLC.18 SDLC could not be initialized because there is no SDLC link configuration for this interface.
STR sdlc18_interface	1.3.6.1.4.1.2007.1.4.90.1.18.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.18
sdlcEventObjects19	1.3.6.1.4.1.2007.1.4.90.1.19			Event SDLC.19 SDLC could not control one or more signals on the interface. This could occur if you attempt to run SDLC over an unsupported interface.
STR sdlc19_interface	1.3.6.1.4.1.2007.1.4.90.1.19.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.19
STR sdlc19_reason	1.3.6.1.4.1.2007.1.4.90.1.19.2	DisplayString	accessible-for-notify	Parameter 'reason' in event SDLC.19
sdlcEventObjects20	1.3.6.1.4.1.2007.1.4.90.1.20			Event SDLC.20 SDLC detected a fault on the link, and terminated all active SDLC connections on the link. This is usually due to a loss of DSR, CTS, or DCD on a full-duplex line, or loss of DSR on a half-duplex line.
STR sdlc20_interface	1.3.6.1.4.1.2007.1.4.90.1.20.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.20
I32 sdlc20_address	1.3.6.1.4.1.2007.1.4.90.1.20.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.20
sdlcEventObjects21	1.3.6.1.4.1.2007.1.4.90.1.21			Event SDLC.21 SDLC has received more than the number of frames configured as the RECEIVE WINDOW before SDLC could respond.
STR sdlc21_interface	1.3.6.1.4.1.2007.1.4.90.1.21.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.21
I32 sdlc21_address	1.3.6.1.4.1.2007.1.4.90.1.21.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.21
sdlcEventObjects22	1.3.6.1.4.1.2007.1.4.90.1.22			Event SDLC.22 The router detected a SDLC protocol error. As a result, the router terminated the SDLC connection.
STR sdlc22_interface	1.3.6.1.4.1.2007.1.4.90.1.22.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.22
I32 sdlc22_address	1.3.6.1.4.1.2007.1.4.90.1.22.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.22
sdlcEventObjects23	1.3.6.1.4.1.2007.1.4.90.1.23			Event SDLC.23 The remote link station is not responding to XID frames the router sent.
STR sdlc23_interface	1.3.6.1.4.1.2007.1.4.90.1.23.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.23
I32 sdlc23_address	1.3.6.1.4.1.2007.1.4.90.1.23.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.23
sdlcEventObjects24	1.3.6.1.4.1.2007.1.4.90.1.24			Event SDLC.24 The remote link station is not responding to TEST frames the router sent.
STR sdlc24_interface	1.3.6.1.4.1.2007.1.4.90.1.24.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.24
I32 sdlc24_address	1.3.6.1.4.1.2007.1.4.90.1.24.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.24
sdlcEventObjects25	1.3.6.1.4.1.2007.1.4.90.1.25			Event SDLC.25 The remote link station is not responding to SNRM frames the router sent. The connection attempt has failed.
STR sdlc25_interface	1.3.6.1.4.1.2007.1.4.90.1.25.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.25
I32 sdlc25_address	1.3.6.1.4.1.2007.1.4.90.1.25.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.25
sdlcEventObjects26	1.3.6.1.4.1.2007.1.4.90.1.26			Event SDLC.26 The remote link station is not responding to polls (RR or RNR) sent by the router. As a result, the router terminated the connection.
STR sdlc26_interface	1.3.6.1.4.1.2007.1.4.90.1.26.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.26
I32 sdlc26_address	1.3.6.1.4.1.2007.1.4.90.1.26.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.26
sdlcEventObjects27	1.3.6.1.4.1.2007.1.4.90.1.27			Event SDLC.27 SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received a frame with an invalid control field.
STR sdlc27_interface	1.3.6.1.4.1.2007.1.4.90.1.27.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.27
I32 sdlc27_address	1.3.6.1.4.1.2007.1.4.90.1.27.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.27
sdlcEventObjects28	1.3.6.1.4.1.2007.1.4.90.1.28			Event SDLC.28 SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received a frame that was too short.
STR sdlc28_interface	1.3.6.1.4.1.2007.1.4.90.1.28.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.28
I32 sdlc28_address	1.3.6.1.4.1.2007.1.4.90.1.28.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.28
sdlcEventObjects29	1.3.6.1.4.1.2007.1.4.90.1.29			Event SDLC.29 SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received a frame that was too long.
STR sdlc29_interface	1.3.6.1.4.1.2007.1.4.90.1.29.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.29
I32 sdlc29_address	1.3.6.1.4.1.2007.1.4.90.1.29.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.29
sdlcEventObjects30	1.3.6.1.4.1.2007.1.4.90.1.30			Event SDLC.30 SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received a frame with an invalid N(r) in the control field.
STR sdlc30_interface	1.3.6.1.4.1.2007.1.4.90.1.30.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.30
I32 sdlc30_address	1.3.6.1.4.1.2007.1.4.90.1.30.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.30
sdlcEventObjects31	1.3.6.1.4.1.2007.1.4.90.1.31			Event SDLC.31 SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received an I-frame with no data in the I field.
STR sdlc31_interface	1.3.6.1.4.1.2007.1.4.90.1.31.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.31
I32 sdlc31_address	1.3.6.1.4.1.2007.1.4.90.1.31.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.31
sdlcEventObjects32	1.3.6.1.4.1.2007.1.4.90.1.32			Event SDLC.32 SDLC has received a frame with an invalid control field.
STR sdlc32_interface	1.3.6.1.4.1.2007.1.4.90.1.32.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.32
I32 sdlc32_address	1.3.6.1.4.1.2007.1.4.90.1.32.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.32
sdlcEventObjects33	1.3.6.1.4.1.2007.1.4.90.1.33			Event SDLC.33 SDLC has received a frame that was too short.
STR sdlc33_interface	1.3.6.1.4.1.2007.1.4.90.1.33.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.33
I32 sdlc33_address	1.3.6.1.4.1.2007.1.4.90.1.33.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.33
sdlcEventObjects34	1.3.6.1.4.1.2007.1.4.90.1.34			Event SDLC.34 SDLC has received a frame that was too long.
STR sdlc34_interface	1.3.6.1.4.1.2007.1.4.90.1.34.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.34
I32 sdlc34_address	1.3.6.1.4.1.2007.1.4.90.1.34.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.34
sdlcEventObjects35	1.3.6.1.4.1.2007.1.4.90.1.35			Event SDLC.35 SDLC has received a frame with an invalid N(r) in the control field.
STR sdlc35_interface	1.3.6.1.4.1.2007.1.4.90.1.35.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.35
I32 sdlc35_address	1.3.6.1.4.1.2007.1.4.90.1.35.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.35
sdlcEventObjects36	1.3.6.1.4.1.2007.1.4.90.1.36			Event SDLC.36 SDLC received a Disconnected Mode (DM) frame. A remote secondary link station sent the frame to indicate that it accepted a previously received DISC frame. The link disconnection is now complete.
STR sdlc36_interface	1.3.6.1.4.1.2007.1.4.90.1.36.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.36
I32 sdlc36_address	1.3.6.1.4.1.2007.1.4.90.1.36.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.36
sdlcEventObjects37	1.3.6.1.4.1.2007.1.4.90.1.37			Event SDLC.37 SDLC received a Request Disconnect (RD) frame. The SDLC client should respond to this by sending a Disconnect (DISC) frame.
STR sdlc37_interface	1.3.6.1.4.1.2007.1.4.90.1.37.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.37
I32 sdlc37_address	1.3.6.1.4.1.2007.1.4.90.1.37.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.37
sdlcEventObjects38	1.3.6.1.4.1.2007.1.4.90.1.38			Event SDLC.38 SDLC received a Request Initialization Mode (RIM) frame. The SDLC client should respond to this by sending a Set Initialization Mode (SIM) frame.
STR sdlc38_interface	1.3.6.1.4.1.2007.1.4.90.1.38.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.38
I32 sdlc38_address	1.3.6.1.4.1.2007.1.4.90.1.38.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.38
sdlcEventObjects39	1.3.6.1.4.1.2007.1.4.90.1.39			Event SDLC.39 Inactivity detection.
STR sdlc39_interface	1.3.6.1.4.1.2007.1.4.90.1.39.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.39
I32 sdlc39_address	1.3.6.1.4.1.2007.1.4.90.1.39.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.39
sdlcEventObjects40	1.3.6.1.4.1.2007.1.4.90.1.40			Event SDLC.40 SDLC entered a frame reject (FRMR) state because it received a frame with an invalid control field.
STR sdlc40_interface	1.3.6.1.4.1.2007.1.4.90.1.40.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.40
I32 sdlc40_address	1.3.6.1.4.1.2007.1.4.90.1.40.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.40
sdlcEventObjects41	1.3.6.1.4.1.2007.1.4.90.1.41			Event SDLC.41 SDLC entered a frame reject (FRMR) state because it received a frame that was too short.
STR sdlc41_interface	1.3.6.1.4.1.2007.1.4.90.1.41.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.41
I32 sdlc41_address	1.3.6.1.4.1.2007.1.4.90.1.41.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.41
sdlcEventObjects42	1.3.6.1.4.1.2007.1.4.90.1.42			Event SDLC.42 SDLC entered a frame reject (FRMR) state because it received a frame that was too long.
STR sdlc42_interface	1.3.6.1.4.1.2007.1.4.90.1.42.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.42
I32 sdlc42_address	1.3.6.1.4.1.2007.1.4.90.1.42.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.42
sdlcEventObjects43	1.3.6.1.4.1.2007.1.4.90.1.43			Event SDLC.43 SDLC entered a frame reject (FRMR) state because it received a frame with an invalid N(r) in the control field.
STR sdlc43_interface	1.3.6.1.4.1.2007.1.4.90.1.43.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.43
I32 sdlc43_address	1.3.6.1.4.1.2007.1.4.90.1.43.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.43
sdlcEventObjects44	1.3.6.1.4.1.2007.1.4.90.1.44			Event SDLC.44 SDLC received a SNRM while in Normal Response Mode (NRM) state.
STR sdlc44_interface	1.3.6.1.4.1.2007.1.4.90.1.44.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.44
I32 sdlc44_address	1.3.6.1.4.1.2007.1.4.90.1.44.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.44
sdlcEventObjects45	1.3.6.1.4.1.2007.1.4.90.1.45			Event SDLC.45 The user disabled the interface from the SDLC console. All current connections are terminated.
STR sdlc45_interface	1.3.6.1.4.1.2007.1.4.90.1.45.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.45
I32 sdlc45_address	1.3.6.1.4.1.2007.1.4.90.1.45.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.45
sdlcEventObjects46	1.3.6.1.4.1.2007.1.4.90.1.46			Event SDLC.46 The user enabled the interface from the SDLC console.
STR sdlc46_interface	1.3.6.1.4.1.2007.1.4.90.1.46.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.46
I32 sdlc46_address	1.3.6.1.4.1.2007.1.4.90.1.46.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.46
sdlcEventObjects47	1.3.6.1.4.1.2007.1.4.90.1.47			Event SDLC.47 The interface has been closed by SDLC. SDLC is no longer running over this interface.
STR sdlc47_interface	1.3.6.1.4.1.2007.1.4.90.1.47.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.47
sdlcEventObjects48	1.3.6.1.4.1.2007.1.4.90.1.48			Event SDLC.48 The user disabled a remote link station on this interface from the SDLC console. Any existing connection was terminated.
STR sdlc48_interface	1.3.6.1.4.1.2007.1.4.90.1.48.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.48
I32 sdlc48_address	1.3.6.1.4.1.2007.1.4.90.1.48.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.48
sdlcEventObjects49	1.3.6.1.4.1.2007.1.4.90.1.49			Event SDLC.49 The user enabled a remote link station has been enabled on this interface from the SDLC console.
STR sdlc49_interface	1.3.6.1.4.1.2007.1.4.90.1.49.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.49
I32 sdlc49_address	1.3.6.1.4.1.2007.1.4.90.1.49.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.49
sdlcEventObjects50	1.3.6.1.4.1.2007.1.4.90.1.50			Event SDLC.50 The router received an Unnumbered Information (UI) frame on this interface.
STR sdlc50_interface	1.3.6.1.4.1.2007.1.4.90.1.50.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.50
I32 sdlc50_address	1.3.6.1.4.1.2007.1.4.90.1.50.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.50
STR sdlc50_octets	1.3.6.1.4.1.2007.1.4.90.1.50.3	DisplayString	accessible-for-notify	Parameter 'octets' in event SDLC.50
sdlcEventObjects51	1.3.6.1.4.1.2007.1.4.90.1.51			Event SDLC.51 The router transmitted an Unnumbered Information (UI) frame on this interface.
STR sdlc51_interface	1.3.6.1.4.1.2007.1.4.90.1.51.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.51
I32 sdlc51_address	1.3.6.1.4.1.2007.1.4.90.1.51.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.51
STR sdlc51_octets	1.3.6.1.4.1.2007.1.4.90.1.51.3	DisplayString	accessible-for-notify	Parameter 'octets' in event SDLC.51
sdlcEventObjects52	1.3.6.1.4.1.2007.1.4.90.1.52			Event SDLC.52 The router received an Information (I) frame on this interface. To log all received SDLC frames, use SDLC-9.
STR sdlc52_interface	1.3.6.1.4.1.2007.1.4.90.1.52.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.52
I32 sdlc52_address	1.3.6.1.4.1.2007.1.4.90.1.52.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.52
I32 sdlc52_byte_count	1.3.6.1.4.1.2007.1.4.90.1.52.3	Integer32	accessible-for-notify	Parameter 'byte-count' in event SDLC.52
STR sdlc52_octets	1.3.6.1.4.1.2007.1.4.90.1.52.4	DisplayString	accessible-for-notify	Parameter 'octets' in event SDLC.52
sdlcEventObjects53	1.3.6.1.4.1.2007.1.4.90.1.53			Event SDLC.53 The router transmitted an Information (I) frame has been transmitted on this interface. To log all received SDLC frames, use SDLC-8.
STR sdlc53_interface	1.3.6.1.4.1.2007.1.4.90.1.53.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.53
I32 sdlc53_address	1.3.6.1.4.1.2007.1.4.90.1.53.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.53
I32 sdlc53_byte_count	1.3.6.1.4.1.2007.1.4.90.1.53.3	Integer32	accessible-for-notify	Parameter 'byte-count' in event SDLC.53
STR sdlc53_octets	1.3.6.1.4.1.2007.1.4.90.1.53.4	DisplayString	accessible-for-notify	Parameter 'octets' in event SDLC.53
sdlcEventObjects54	1.3.6.1.4.1.2007.1.4.90.1.54			Event SDLC.54 The max BTU size configured for a remote link station exceeds that defined for the link. The router adjusted the value for the remote link station temporarily. To avoid this message in the future, change the max BTU size with the SET REMOTE MAX-PACKET command.
STR sdlc54_interface	1.3.6.1.4.1.2007.1.4.90.1.54.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.54
I32 sdlc54_address	1.3.6.1.4.1.2007.1.4.90.1.54.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.54
I32 sdlc54_oldBTUSize	1.3.6.1.4.1.2007.1.4.90.1.54.3	Integer32	accessible-for-notify	Parameter 'oldBTUSize' in event SDLC.54
I32 sdlc54_newBTUSize	1.3.6.1.4.1.2007.1.4.90.1.54.4	Integer32	accessible-for-notify	Parameter 'newBTUSize' in event SDLC.54
sdlcEventObjects55	1.3.6.1.4.1.2007.1.4.90.1.55			Event SDLC.55 The modulo for this link has been changed by the user, rendering the window sizes for all pre-defined remote link stations invalid. The window size has been temporarily adjusted. When a link is configured for mod-8, the valid window sizes are 0 to 7. When the link is configured for mod-128, the valid window sizes are 8 to 128. To avoid this message in the future, change the receive window size with the 'SET REMOTE RECEIVE-WINDOW' command.
STR sdlc55_interface	1.3.6.1.4.1.2007.1.4.90.1.55.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.55
I32 sdlc55_address	1.3.6.1.4.1.2007.1.4.90.1.55.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.55
I32 sdlc55_oldRxWindow	1.3.6.1.4.1.2007.1.4.90.1.55.3	Integer32	accessible-for-notify	Parameter 'oldRxWindow' in event SDLC.55
I32 sdlc55_newRxWindow	1.3.6.1.4.1.2007.1.4.90.1.55.4	Integer32	accessible-for-notify	Parameter 'newRxWindow' in event SDLC.55
sdlcEventObjects56	1.3.6.1.4.1.2007.1.4.90.1.56			Event SDLC.56 The modulo for this link has been changed by the user, rendering the window sizes for all pre-defined remote link stations invalid. The window size has been temporarily adjusted. When a link is configured for mod-8, the valid window sizes are 0 to 7. When the link is configured for mod-128, the valid window sizes are 8 to 128. To avoid this message in the future, change the transmit window size with the 'SET REMOTE TRANSMIT-WINDOW' command.
STR sdlc56_interface	1.3.6.1.4.1.2007.1.4.90.1.56.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.56
I32 sdlc56_address	1.3.6.1.4.1.2007.1.4.90.1.56.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.56
I32 sdlc56_oldTxWindow	1.3.6.1.4.1.2007.1.4.90.1.56.3	Integer32	accessible-for-notify	Parameter 'oldTxWindow' in event SDLC.56
I32 sdlc56_newTxWindow	1.3.6.1.4.1.2007.1.4.90.1.56.4	Integer32	accessible-for-notify	Parameter 'newTxWindow' in event SDLC.56
sdlcEventObjects57	1.3.6.1.4.1.2007.1.4.90.1.57			Event SDLC.57 The link configuration was somehow corrupted, possibly due to a software upgrade. A default link configuration has been created. Before operating SDLC, review the newly-created configuration and adjust as necessary.
STR sdlc57_interface	1.3.6.1.4.1.2007.1.4.90.1.57.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.57
sdlcEventObjects58	1.3.6.1.4.1.2007.1.4.90.1.58			Event SDLC.58 An invalid XID/TEST timeout value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the XID/TEST timeout from the SDLC config prompt for this interface.
STR sdlc58_interface	1.3.6.1.4.1.2007.1.4.90.1.58.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.58
sdlcEventObjects59	1.3.6.1.4.1.2007.1.4.90.1.59			Event SDLC.59 An invalid XID/TEST retry value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the XID/TEST retry count from the SDLC config prompt for this interface.
STR sdlc59_interface	1.3.6.1.4.1.2007.1.4.90.1.59.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.59
sdlcEventObjects60	1.3.6.1.4.1.2007.1.4.90.1.60			Event SDLC.60 An invalid SNRM timeout value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the SNRM timeout from the SDLC config prompt for this interface.
STR sdlc60_interface	1.3.6.1.4.1.2007.1.4.90.1.60.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.60
sdlcEventObjects61	1.3.6.1.4.1.2007.1.4.90.1.61			Event SDLC.61 An invalid SNRM retry value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the SNRM retry count from the SDLC config prompt for this interface.
STR sdlc61_interface	1.3.6.1.4.1.2007.1.4.90.1.61.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.61
sdlcEventObjects62	1.3.6.1.4.1.2007.1.4.90.1.62			Event SDLC.62 An invalid POLL timeout value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the POLL timeout from the SDLC config prompt for this interface.
STR sdlc62_interface	1.3.6.1.4.1.2007.1.4.90.1.62.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.62
sdlcEventObjects63	1.3.6.1.4.1.2007.1.4.90.1.63			Event SDLC.63 An invalid inter-POLL delay value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the inter-POLL delay from the SDLC config prompt for this interface.
STR sdlc63_interface	1.3.6.1.4.1.2007.1.4.90.1.63.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.63
sdlcEventObjects64	1.3.6.1.4.1.2007.1.4.90.1.64			Event SDLC.64 An invalid POLL retry value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the POLL retry count from the SDLC config prompt for this interface.
STR sdlc64_interface	1.3.6.1.4.1.2007.1.4.90.1.64.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.64
sdlcEventObjects65	1.3.6.1.4.1.2007.1.4.90.1.65			Event SDLC.65 An invalid inactivity timeout value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the inactivity timeout from the SDLC config prompt for this interface.
STR sdlc65_interface	1.3.6.1.4.1.2007.1.4.90.1.65.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.65
sdlcEventObjects66	1.3.6.1.4.1.2007.1.4.90.1.66			Event SDLC.66 An invalid RTS hold value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the RTS hold value from the SDLC config prompt for this interface.
STR sdlc66_interface	1.3.6.1.4.1.2007.1.4.90.1.66.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.66
sdlcEventObjects67	1.3.6.1.4.1.2007.1.4.90.1.67			Event SDLC.67 An invalid maximum frame size value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the maximum frame size from the SDLC config prompt for this interface.
STR sdlc67_interface	1.3.6.1.4.1.2007.1.4.90.1.67.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.67
sdlcEventObjects68	1.3.6.1.4.1.2007.1.4.90.1.68			Event SDLC.68 The link counters have been reset from the SDLC console.
STR sdlc68_interface	1.3.6.1.4.1.2007.1.4.90.1.68.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.68
sdlcEventObjects69	1.3.6.1.4.1.2007.1.4.90.1.69			Event SDLC.69 The link counters could not be reset from the SDLC console. This is usually a temporary condition. Retry the operation.
STR sdlc69_interface	1.3.6.1.4.1.2007.1.4.90.1.69.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.69
sdlcEventObjects70	1.3.6.1.4.1.2007.1.4.90.1.70			Event SDLC.70 The user reset the counters for a remote secondary station from the SDLC console.
STR sdlc70_interface	1.3.6.1.4.1.2007.1.4.90.1.70.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.70
I32 sdlc70_address	1.3.6.1.4.1.2007.1.4.90.1.70.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.70
sdlcEventObjects71	1.3.6.1.4.1.2007.1.4.90.1.71			Event SDLC.71 The user could not reset the counters for a remote secondary station from the SDLC console. This is usually a temporary condition. Retry the operation.
STR sdlc71_interface	1.3.6.1.4.1.2007.1.4.90.1.71.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.71
I32 sdlc71_address	1.3.6.1.4.1.2007.1.4.90.1.71.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.71
sdlcEventObjects72	1.3.6.1.4.1.2007.1.4.90.1.72			Event SDLC.72 The remote link station has been closed by the router and is no longer active.
STR sdlc72_interface	1.3.6.1.4.1.2007.1.4.90.1.72.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.72
I32 sdlc72_address	1.3.6.1.4.1.2007.1.4.90.1.72.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.72
sdlcEventObjects73	1.3.6.1.4.1.2007.1.4.90.1.73			Event SDLC.73 SDLC failed to allocate memory from the router's heap because it has already allocated its fair share. SDLC will recover from this usually temporary problem.
STR sdlc73_interface	1.3.6.1.4.1.2007.1.4.90.1.73.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.73
sdlcEventObjects74	1.3.6.1.4.1.2007.1.4.90.1.74			Event SDLC.74 SDLC failed to allocate a high-priority buffer from the router's heap. As a result, SDLC will temporarily experience a loss of performance. SDLC sessions could possibly be lost if the condition persists.
STR sdlc74_interface	1.3.6.1.4.1.2007.1.4.90.1.74.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.74
sdlcEventObjects75	1.3.6.1.4.1.2007.1.4.90.1.75			Event SDLC.75 SDLC failed to allocate memory from the router's heap because the heap is exhausted. SDLC will recover from this usually temporary problem.
STR sdlc75_interface	1.3.6.1.4.1.2007.1.4.90.1.75.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.75
sdlcEventObjects76	1.3.6.1.4.1.2007.1.4.90.1.76			Event SDLC.76 SDLC could not send an Information (I) frame to the interface. SDLC will attempt to re-transmit it later.
STR sdlc76_interface	1.3.6.1.4.1.2007.1.4.90.1.76.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.76
sdlcEventObjects77	1.3.6.1.4.1.2007.1.4.90.1.77			Event SDLC.77 SDLC could not send a Supervisory (S) frame to the interface. SDLC will attempt to re-transmit it later.
STR sdlc77_interface	1.3.6.1.4.1.2007.1.4.90.1.77.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.77
sdlcEventObjects78	1.3.6.1.4.1.2007.1.4.90.1.78			Event SDLC.78 SDLC could not send an Unnumbered Information (UI) frame to the interface. SDLC will attempt to re-transmit it later.
STR sdlc78_interface	1.3.6.1.4.1.2007.1.4.90.1.78.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.78
sdlcEventObjects79	1.3.6.1.4.1.2007.1.4.90.1.79			Event SDLC.79 SDLC could not send an XID or TEST frame to the interface. SDLC will attempt to re-transmit it later.
STR sdlc79_interface	1.3.6.1.4.1.2007.1.4.90.1.79.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.79
sdlcEventObjects80	1.3.6.1.4.1.2007.1.4.90.1.80			Event SDLC.80 SDLC received an invalid frame type. This frame was ignored.
STR sdlc80_interface	1.3.6.1.4.1.2007.1.4.90.1.80.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.80
sdlcEventObjects81	1.3.6.1.4.1.2007.1.4.90.1.81			Event SDLC.81 SDLC received a frame from a remote link station that it had not polled. This frame was ignored. This error may also occur if the poll response timeout is too short.
STR sdlc81_interface	1.3.6.1.4.1.2007.1.4.90.1.81.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.81
sdlcEventObjects82	1.3.6.1.4.1.2007.1.4.90.1.82			Event SDLC.82 SDLC received an Unnumbered Information (UI) frame without the Final (F) bit set. This frame was dropped.
STR sdlc82_interface	1.3.6.1.4.1.2007.1.4.90.1.82.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.82
sdlcEventObjects83	1.3.6.1.4.1.2007.1.4.90.1.83			Event SDLC.83 SDLC received a frame to the broadcast address on a multipoint line. The frame was dropped.
STR sdlc83_interface	1.3.6.1.4.1.2007.1.4.90.1.83.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.83
sdlcEventObjects84	1.3.6.1.4.1.2007.1.4.90.1.84			Event SDLC.84 SDLC could not be initialized because there is no SDLC link configuration for this interface.
STR sdlc84_interface	1.3.6.1.4.1.2007.1.4.90.1.84.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.84
sdlcEventObjects85	1.3.6.1.4.1.2007.1.4.90.1.85			Event SDLC.85 SDLC could not control one or more signals on the interface. This could occur if you attempt to run SDLC over an unsupported interface.
STR sdlc85_interface	1.3.6.1.4.1.2007.1.4.90.1.85.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.85
STR sdlc85_reason	1.3.6.1.4.1.2007.1.4.90.1.85.2	DisplayString	accessible-for-notify	Parameter 'reason' in event SDLC.85
sdlcEventObjects86	1.3.6.1.4.1.2007.1.4.90.1.86			Event SDLC.86 DCD went high during transmission of a frame in half duplex mode. This is a protocol violation, and the interface will go down shortly in order to correct the problem.
STR sdlc86_interface	1.3.6.1.4.1.2007.1.4.90.1.86.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.86
sdlcEventObjects87	1.3.6.1.4.1.2007.1.4.90.1.87			Event SDLC.87 The CTS signal has transitioned to low while the interface was recovering from a half-duplex protocol violation. The link is now in the correct state and data transfer may resume.
STR sdlc87_interface	1.3.6.1.4.1.2007.1.4.90.1.87.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.87
sdlcEventObjects88	1.3.6.1.4.1.2007.1.4.90.1.88			Event SDLC.88 A signal was asserted by the connected device while the line was idle. When operating in half-duplex mode, only the DTR/DSR signal should be asserted on an idle interface.
STR sdlc88_interface	1.3.6.1.4.1.2007.1.4.90.1.88.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.88
sdlcEventObjects89	1.3.6.1.4.1.2007.1.4.90.1.89			Event SDLC.89 The DSR or CTS signal went low during transmission. This is a protocol violation, and the interface will go down shortly in order to correct the problem.
STR sdlc89_interface	1.3.6.1.4.1.2007.1.4.90.1.89.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.89
sdlcEventObjects90	1.3.6.1.4.1.2007.1.4.90.1.90			Event SDLC.90 SDLC received a frame other than a UA while trying to close the link station. The router ignored this frame.
STR sdlc90_interface	1.3.6.1.4.1.2007.1.4.90.1.90.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.90
I32 sdlc90_address	1.3.6.1.4.1.2007.1.4.90.1.90.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.90
sdlcEventObjects91	1.3.6.1.4.1.2007.1.4.90.1.91			Event SDLC.91 An SDLC remote link station was added by the user from the SDLC console and is now available for use.
I32 sdlc91_address	1.3.6.1.4.1.2007.1.4.90.1.91.1	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.91
STR sdlc91_interface	1.3.6.1.4.1.2007.1.4.90.1.91.2	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.91
sdlcEventObjects92	1.3.6.1.4.1.2007.1.4.90.1.92			Event SDLC.92 An SDLC remote link station was deleted by the user from the SDLC console and is no longer available for use.
I32 sdlc92_address	1.3.6.1.4.1.2007.1.4.90.1.92.1	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.92
STR sdlc92_interface	1.3.6.1.4.1.2007.1.4.90.1.92.2	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.92
sdlcEventObjects93	1.3.6.1.4.1.2007.1.4.90.1.93			Event SDLC.93 SDLC received a frame from a remote link station that contains an unrecognized station address. The router ignored this frame.
STR sdlc93_interface	1.3.6.1.4.1.2007.1.4.90.1.93.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.93
sdlcEventObjects94	1.3.6.1.4.1.2007.1.4.90.1.94			Event SDLC.94 The router ignored the received frame for this station, because the target station is in a disabled state.
STR sdlc94_interface	1.3.6.1.4.1.2007.1.4.90.1.94.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.94
I32 sdlc94_address	1.3.6.1.4.1.2007.1.4.90.1.94.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.94
sdlcEventObjects95	1.3.6.1.4.1.2007.1.4.90.1.95			Event SDLC.95 The local SDLC secondary link station received a null XID frame from a remote link station while in NRM. We treat this as an indication that the link failed at the sending end and this is an attempt to reestablish the connection.
STR sdlc95_interface	1.3.6.1.4.1.2007.1.4.90.1.95.1	DisplayString	accessible-for-notify	Parameter 'interface' in event SDLC.95
I32 sdlc95_address	1.3.6.1.4.1.2007.1.4.90.1.95.2	Integer32	accessible-for-notify	Parameter 'address' in event SDLC.95
sdlcNotifications	1.3.6.1.4.1.2007.1.4.90.2
sdlcNotificationsPrefix	1.3.6.1.4.1.2007.1.4.90.2.0
NTF sdlcNotification1	1.3.6.1.4.1.2007.1.4.90.2.0.1			Notification of Event SDLC.1 Message: 'SDLC support installed for QSL, on interface $1' Parameters list: $1: sdlc1-interface DLSw SDLC has been initialized for operation over the serial device and is now available for use in the router.
NTF sdlcNotification2	1.3.6.1.4.1.2007.1.4.90.2.0.2			Notification of Event SDLC.2 Message: 'No remote configuration was defined for SDLC address $1 - default settings used, on interface $2' Parameters list: $1: sdlc2-address $2: sdlc2-interface An open was attempted on an SDLC station, but a configuration record was not defined via the ADD STATION command. The station will be opened using default configuration value. This station will be listed in the monitor process LIST STATION ALL command. An asterisk * next to the station address signifies that a default configuration is in use.
NTF sdlcNotification3	1.3.6.1.4.1.2007.1.4.90.2.0.3			Notification of Event SDLC.3 Message: 'Cannot copy a user buffer to to SDLC - Out of memory, on interface $1' Parameters list: $1: sdlc3-interface There is currently no memory available to copy user data to SDLC. Another attempt will be made at a later time.
NTF sdlcNotification4	1.3.6.1.4.1.2007.1.4.90.2.0.4			Notification of Event SDLC.4 Message: 'Inbound frame was dropped - SDLC not yet active on interface $1' Parameters list: $1: sdlc4-interface A frame was received on an interface that is not yet owned by an SDLC client. All packets received are dropped until an SDLC client opens the port for use.
NTF sdlcNotification5	1.3.6.1.4.1.2007.1.4.90.2.0.5			Notification of Event SDLC.5 Message: 'Packet dropped due to no SDLC credit or memory shortage, on interface $1. Temporary' Parameters list: $1: sdlc5-interface An incoming packet was dropped due to no SDLC receive credit or a temporary memory shortage.
NTF sdlcNotification6	1.3.6.1.4.1.2007.1.4.90.2.0.6			Notification of Event SDLC.6 Message: 'Packet received with I-ERR set, on interface $1' Parameters list: $1: sdlc6-interface real-sdlc-in received a packet with I-ERR set.
NTF sdlcNotification7	1.3.6.1.4.1.2007.1.4.90.2.0.7			Notification of Event SDLC.7 Message: 'Failure to send packet to device, on interface $1, status = $2' Parameters list: $1: sdlc7-interface $2: sdlc7-status The call to netsend() failed while trying to send a frame from SDLC.
NTF sdlcNotification8	1.3.6.1.4.1.2007.1.4.90.2.0.8			Notification of Event SDLC.8 Message: 'Transmit $1 bytes to link station $2, on interface $3:$4' Parameters list: $1: sdlc8-count $2: sdlc8-address $3: sdlc8-interface $4: sdlc8-octets The router transmitted an SDLC frame. This is the entire frame, including the SDLC header. The router logs all transmitted SDLC frames with this message. To log only transmitted SDLC I-frames, use SDLC-53.
NTF sdlcNotification9	1.3.6.1.4.1.2007.1.4.90.2.0.9			Notification of Event SDLC.9 Message: 'Received $1 bytes from link station $2, on interface $3:$4' Parameters list: $1: sdlc9-count $2: sdlc9-address $3: sdlc9-interface $4: sdlc9-octets The router received an SDLC frame. This is the entire frame, including the SDLC header. The router logs all received SDLC frames with this message. To log only received SDLC I-frames, use SDLC-52.
NTF sdlcNotification10	1.3.6.1.4.1.2007.1.4.90.2.0.10			Notification of Event SDLC.10 Message: 'Request to bring up SDLC, on interface $1' Parameters list: $1: sdlc10-interface An entity in the router has attached to the interface and can now use SDLC services.
NTF sdlcNotification11	1.3.6.1.4.1.2007.1.4.90.2.0.11			Notification of Event SDLC.11 Message: 'Request to bring down SDLC, on interface $1' Parameters list: $1: sdlc11-interface An entity in the router is no longer using SDLC services on this interface.
NTF sdlcNotification12	1.3.6.1.4.1.2007.1.4.90.2.0.12			Notification of Event SDLC.12 Message: 'Link status change $1 occurred, on interface $2' Parameters list: $1: sdlc12-exception $2: sdlc12-interface An interface signal has changed state. Note: an unwieldy number of these messages will be generated when the interface is operating in half duplex mode.
NTF sdlcNotification13	1.3.6.1.4.1.2007.1.4.90.2.0.13			Notification of Event SDLC.13 Message: 'Station $1 is now UP, on interface $2' Parameters list: $1: sdlc13-address $2: sdlc13-interface The SDLC link is now operating in Normal Response Mode, meaning that a SDLC connection is now in progress.
NTF sdlcNotification14	1.3.6.1.4.1.2007.1.4.90.2.0.14			Notification of Event SDLC.14 Message: 'Remote station refused SNRM, link station $1 remains DOWN on interface $2' Parameters list: $1: sdlc14-address $2: sdlc14-interface An attempt by the router to connect to a remote link station has been refused.
NTF sdlcNotification15	1.3.6.1.4.1.2007.1.4.90.2.0.15			Notification of Event SDLC.15 Message: 'Station $1 is now DOWN, on interface $2' Parameters list: $1: sdlc15-address $2: sdlc15-interface The SDLC link is now operating in Normal Disconnect Mode, meaning that a SDLC connection has been terminated in an orderly fashion.
NTF sdlcNotification16	1.3.6.1.4.1.2007.1.4.90.2.0.16			Notification of Event SDLC.16 Message: 'An exception occurred on Link Station $1: exception $2, on interface $3' Parameters list: $1: sdlc16-address $2: sdlc16-exception $3: sdlc16-interface The SDLC protocol has been initialized.
NTF sdlcNotification17	1.3.6.1.4.1.2007.1.4.90.2.0.17			Notification of Event SDLC.17 Message: 'Interface $1: received a broadcast frame from a secondary station on a multipoint line - dropped' Parameters list: $1: sdlc17-interface SDLC received a frame to the broadcast address on a multipoint line. The frame was dropped.
NTF sdlcNotification18	1.3.6.1.4.1.2007.1.4.90.2.0.18			Notification of Event SDLC.18 Message: 'Interface $1: SDLC not brought up because no LINK configuration is defined' Parameters list: $1: sdlc18-interface SDLC could not be initialized because there is no SDLC link configuration for this interface.
NTF sdlcNotification19	1.3.6.1.4.1.2007.1.4.90.2.0.19			Notification of Event SDLC.19 Message: 'Interface $1: signal control request failed because $2' Parameters list: $1: sdlc19-interface $2: sdlc19-reason SDLC could not control one or more signals on the interface. This could occur if you attempt to run SDLC over an unsupported interface.
NTF sdlcNotification20	1.3.6.1.4.1.2007.1.4.90.2.0.20			Notification of Event SDLC.20 Message: 'Interface $1 SDLC station $2: DLC-LINK-FAULT-CONDITION' Parameters list: $1: sdlc20-interface $2: sdlc20-address SDLC detected a fault on the link, and terminated all active SDLC connections on the link. This is usually due to a loss of DSR, CTS, or DCD on a full-duplex line, or loss of DSR on a half-duplex line.
NTF sdlcNotification21	1.3.6.1.4.1.2007.1.4.90.2.0.21			Notification of Event SDLC.21 Message: 'Interface $1 SDLC station $2: DLC-RX-EXCEED-WINDOW-SIZE' Parameters list: $1: sdlc21-interface $2: sdlc21-address SDLC has received more than the number of frames configured as the RECEIVE WINDOW before SDLC could respond.
NTF sdlcNotification22	1.3.6.1.4.1.2007.1.4.90.2.0.22			Notification of Event SDLC.22 Message: 'Interface $1 SDLC station $2: DLC-RX-LOCAL-PROTOCOL-ERROR' Parameters list: $1: sdlc22-interface $2: sdlc22-address The router detected a SDLC protocol error. As a result, the router terminated the SDLC connection.
NTF sdlcNotification23	1.3.6.1.4.1.2007.1.4.90.2.0.23			Notification of Event SDLC.23 Message: 'Interface $1 SDLC station $2: DLC-XID-RETRY-LIMIT-REACHED' Parameters list: $1: sdlc23-interface $2: sdlc23-address The remote link station is not responding to XID frames the router sent.
NTF sdlcNotification24	1.3.6.1.4.1.2007.1.4.90.2.0.24			Notification of Event SDLC.24 Message: 'Interface $1 SDLC station $2: DLC-TEST-RETRY-LIMIT-REACHED' Parameters list: $1: sdlc24-interface $2: sdlc24-address The remote link station is not responding to TEST frames the router sent.
NTF sdlcNotification25	1.3.6.1.4.1.2007.1.4.90.2.0.25			Notification of Event SDLC.25 Message: 'Interface $1 SDLC station $2: DLC-SNRM-RETRY-LIMIT-REACHED' Parameters list: $1: sdlc25-interface $2: sdlc25-address The remote link station is not responding to SNRM frames the router sent. The connection attempt has failed.
NTF sdlcNotification26	1.3.6.1.4.1.2007.1.4.90.2.0.26			Notification of Event SDLC.26 Message: 'Interface $1 SDLC station $2: DLC-POLL-RETRY-LIMIT-REACHED' Parameters list: $1: sdlc26-interface $2: sdlc26-address The remote link station is not responding to polls (RR or RNR) sent by the router. As a result, the router terminated the connection.
NTF sdlcNotification27	1.3.6.1.4.1.2007.1.4.90.2.0.27			Notification of Event SDLC.27 Message: 'Interface $1 SDLC station $2: DLC-RX-FRMR-INV-CTL-FIELD' Parameters list: $1: sdlc27-interface $2: sdlc27-address SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received a frame with an invalid control field.
NTF sdlcNotification28	1.3.6.1.4.1.2007.1.4.90.2.0.28			Notification of Event SDLC.28 Message: 'Interface $1 SDLC station $2: DLC-RX-FRMR-INV-LENGTH' Parameters list: $1: sdlc28-interface $2: sdlc28-address SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received a frame that was too short.
NTF sdlcNotification29	1.3.6.1.4.1.2007.1.4.90.2.0.29			Notification of Event SDLC.29 Message: 'Interface $1 SDLC station $2: DLC-RX-FRMR-LONG-I-FIELD' Parameters list: $1: sdlc29-interface $2: sdlc29-address SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received a frame that was too long.
NTF sdlcNotification30	1.3.6.1.4.1.2007.1.4.90.2.0.30			Notification of Event SDLC.30 Message: 'Interface $1 SDLC station $2: DLC-RX-FRMR-INV-NR' Parameters list: $1: sdlc30-interface $2: sdlc30-address SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received a frame with an invalid N(r) in the control field.
NTF sdlcNotification31	1.3.6.1.4.1.2007.1.4.90.2.0.31			Notification of Event SDLC.31 Message: 'Interface $1 SDLC station $2: DLC-RX-FRMR-NO-I-FIELD' Parameters list: $1: sdlc31-interface $2: sdlc31-address SDLC has received a Frame Reject (FRMR) frame indicating that the remote link station received an I-frame with no data in the I field.
NTF sdlcNotification32	1.3.6.1.4.1.2007.1.4.90.2.0.32			Notification of Event SDLC.32 Message: 'Interface $1 SDLC station $2: DLC-RX-FRAME-INV-CTL-FIELD' Parameters list: $1: sdlc32-interface $2: sdlc32-address SDLC has received a frame with an invalid control field.
NTF sdlcNotification33	1.3.6.1.4.1.2007.1.4.90.2.0.33			Notification of Event SDLC.33 Message: 'Interface $1 SDLC station $2: DLC-RX-FRAME-INV-LENGTH' Parameters list: $1: sdlc33-interface $2: sdlc33-address SDLC has received a frame that was too short.
NTF sdlcNotification34	1.3.6.1.4.1.2007.1.4.90.2.0.34			Notification of Event SDLC.34 Message: 'Interface $1 SDLC station $2: DLC-RX-FRAME-LONG-I-FIELD' Parameters list: $1: sdlc34-interface $2: sdlc34-address SDLC has received a frame that was too long.
NTF sdlcNotification35	1.3.6.1.4.1.2007.1.4.90.2.0.35			Notification of Event SDLC.35 Message: 'Interface $1 SDLC station $2: DLC-RX-FRAME-INV-NR' Parameters list: $1: sdlc35-interface $2: sdlc35-address SDLC has received a frame with an invalid N(r) in the control field.
NTF sdlcNotification36	1.3.6.1.4.1.2007.1.4.90.2.0.36			Notification of Event SDLC.36 Message: 'Interface $1 SDLC station $2: DLC-RX-DM' Parameters list: $1: sdlc36-interface $2: sdlc36-address SDLC received a Disconnected Mode (DM) frame. A remote secondary link station sent the frame to indicate that it accepted a previously received DISC frame. The link disconnection is now complete.
NTF sdlcNotification37	1.3.6.1.4.1.2007.1.4.90.2.0.37			Notification of Event SDLC.37 Message: 'Interface $1 SDLC station $2: DLC-RX-RD' Parameters list: $1: sdlc37-interface $2: sdlc37-address SDLC received a Request Disconnect (RD) frame. The SDLC client should respond to this by sending a Disconnect (DISC) frame.
NTF sdlcNotification38	1.3.6.1.4.1.2007.1.4.90.2.0.38			Notification of Event SDLC.38 Message: 'Interface $1 SDLC station $2: DLC-RX-RIM' Parameters list: $1: sdlc38-interface $2: sdlc38-address SDLC received a Request Initialization Mode (RIM) frame. The SDLC client should respond to this by sending a Set Initialization Mode (SIM) frame.
NTF sdlcNotification39	1.3.6.1.4.1.2007.1.4.90.2.0.39			Notification of Event SDLC.39 Message: 'Interface $1 SDLC station $2: DLC-LINK-INACTIVITY-DETECTION' Parameters list: $1: sdlc39-interface $2: sdlc39-address Inactivity detection.
NTF sdlcNotification40	1.3.6.1.4.1.2007.1.4.90.2.0.40			Notification of Event SDLC.40 Message: 'Interface $1 SDLC station $2: DLC-TX-FRMR-INV-CTL-FIELD' Parameters list: $1: sdlc40-interface $2: sdlc40-address SDLC entered a frame reject (FRMR) state because it received a frame with an invalid control field.
NTF sdlcNotification41	1.3.6.1.4.1.2007.1.4.90.2.0.41			Notification of Event SDLC.41 Message: 'Interface $1 SDLC station $2: DLC-TX-FRMR-INV-LENGTH' Parameters list: $1: sdlc41-interface $2: sdlc41-address SDLC entered a frame reject (FRMR) state because it received a frame that was too short.
NTF sdlcNotification42	1.3.6.1.4.1.2007.1.4.90.2.0.42			Notification of Event SDLC.42 Message: 'Interface $1 SDLC station $2: DLC-TX-FRMR-LONG-I-FIELD' Parameters list: $1: sdlc42-interface $2: sdlc42-address SDLC entered a frame reject (FRMR) state because it received a frame that was too long.
NTF sdlcNotification43	1.3.6.1.4.1.2007.1.4.90.2.0.43			Notification of Event SDLC.43 Message: 'Interface $1 SDLC station $2: DLC-TX-FRMR-INV-NR' Parameters list: $1: sdlc43-interface $2: sdlc43-address SDLC entered a frame reject (FRMR) state because it received a frame with an invalid N(r) in the control field.
NTF sdlcNotification44	1.3.6.1.4.1.2007.1.4.90.2.0.44			Notification of Event SDLC.44 Message: 'Interface $1 SDLC station $2: DLC-RX-SNRM-WHILE-IN-NRM' Parameters list: $1: sdlc44-interface $2: sdlc44-address SDLC received a SNRM while in Normal Response Mode (NRM) state.
NTF sdlcNotification45	1.3.6.1.4.1.2007.1.4.90.2.0.45			Notification of Event SDLC.45 Message: 'Interface $1 SDLC station $2: DLC-PORT-DISABLED' Parameters list: $1: sdlc45-interface $2: sdlc45-address The user disabled the interface from the SDLC console. All current connections are terminated.
NTF sdlcNotification46	1.3.6.1.4.1.2007.1.4.90.2.0.46			Notification of Event SDLC.46 Message: 'Interface $1 SDLC station $2: DLC-PORT-ENABLED' Parameters list: $1: sdlc46-interface $2: sdlc46-address The user enabled the interface from the SDLC console.
NTF sdlcNotification47	1.3.6.1.4.1.2007.1.4.90.2.0.47			Notification of Event SDLC.47 Message: 'Interface $1 SDLC link: DLC-STATION-CLOSED' Parameters list: $1: sdlc47-interface The interface has been closed by SDLC. SDLC is no longer running over this interface.
NTF sdlcNotification48	1.3.6.1.4.1.2007.1.4.90.2.0.48			Notification of Event SDLC.48 Message: 'Interface $1 SDLC station $2: DLC-LS-DISABLED' Parameters list: $1: sdlc48-interface $2: sdlc48-address The user disabled a remote link station on this interface from the SDLC console. Any existing connection was terminated.
NTF sdlcNotification49	1.3.6.1.4.1.2007.1.4.90.2.0.49			Notification of Event SDLC.49 Message: 'Interface $1 SDLC station $2: DLC-LS-ENABLED' Parameters list: $1: sdlc49-interface $2: sdlc49-address The user enabled a remote link station has been enabled on this interface from the SDLC console.
NTF sdlcNotification50	1.3.6.1.4.1.2007.1.4.90.2.0.50			Notification of Event SDLC.50 Message: 'Interface $1 received UI from SDLC addr $2:$3' Parameters list: $1: sdlc50-interface $2: sdlc50-address $3: sdlc50-octets The router received an Unnumbered Information (UI) frame on this interface.
NTF sdlcNotification51	1.3.6.1.4.1.2007.1.4.90.2.0.51			Notification of Event SDLC.51 Message: 'Interface $1 sent UI to SDLC addr $2:$3' Parameters list: $1: sdlc51-interface $2: sdlc51-address $3: sdlc51-octets The router transmitted an Unnumbered Information (UI) frame on this interface.
NTF sdlcNotification52	1.3.6.1.4.1.2007.1.4.90.2.0.52			Notification of Event SDLC.52 Message: 'Interface $1 received I from SDLC addr $2 $3 bytes:$4' Parameters list: $1: sdlc52-interface $2: sdlc52-address $3: sdlc52-byte-count $4: sdlc52-octets The router received an Information (I) frame on this interface. To log all received SDLC frames, use SDLC-9.
NTF sdlcNotification53	1.3.6.1.4.1.2007.1.4.90.2.0.53			Notification of Event SDLC.53 Message: 'Interface $1 sent I to SDLC addr $2 $3 bytes:$4' Parameters list: $1: sdlc53-interface $2: sdlc53-address $3: sdlc53-byte-count $4: sdlc53-octets The router transmitted an Information (I) frame has been transmitted on this interface. To log all received SDLC frames, use SDLC-8.
NTF sdlcNotification54	1.3.6.1.4.1.2007.1.4.90.2.0.54			Notification of Event SDLC.54 Message: 'Interface $1 Station $2, Max BTU size too large for link - adjusted ($3 -> $4)' Parameters list: $1: sdlc54-interface $2: sdlc54-address $3: sdlc54-oldBTUSize $4: sdlc54-newBTUSize The max BTU size configured for a remote link station exceeds that defined for the link. The router adjusted the value for the remote link station temporarily. To avoid this message in the future, change the max BTU size with the SET REMOTE MAX-PACKET command.
NTF sdlcNotification55	1.3.6.1.4.1.2007.1.4.90.2.0.55			Notification of Event SDLC.55 Message: 'Interface $1 Station $2, Window size is inconsistent with modulo for link - adjusted ($3 -> $4)' Parameters list: $1: sdlc55-interface $2: sdlc55-address $3: sdlc55-oldRxWindow $4: sdlc55-newRxWindow The modulo for this link has been changed by the user, rendering the window sizes for all pre-defined remote link stations invalid. The window size has been temporarily adjusted. When a link is configured for mod-8, the valid window sizes are 0 to 7. When the link is configured for mod-128, the valid window sizes are 8 to 128. To avoid this message in the future, change the receive window size with the 'SET REMOTE RECEIVE-WINDOW' command.
NTF sdlcNotification56	1.3.6.1.4.1.2007.1.4.90.2.0.56			Notification of Event SDLC.56 Message: 'Interface $1 Station $2, Window size is inconsistent with modulo for link - adjusted ($3 -> $4)' Parameters list: $1: sdlc56-interface $2: sdlc56-address $3: sdlc56-oldTxWindow $4: sdlc56-newTxWindow The modulo for this link has been changed by the user, rendering the window sizes for all pre-defined remote link stations invalid. The window size has been temporarily adjusted. When a link is configured for mod-8, the valid window sizes are 0 to 7. When the link is configured for mod-128, the valid window sizes are 8 to 128. To avoid this message in the future, change the transmit window size with the 'SET REMOTE TRANSMIT-WINDOW' command.
NTF sdlcNotification57	1.3.6.1.4.1.2007.1.4.90.2.0.57			Notification of Event SDLC.57 Message: 'Interface $1 - Link configuration corrupted, using defaults' Parameters list: $1: sdlc57-interface The link configuration was somehow corrupted, possibly due to a software upgrade. A default link configuration has been created. Before operating SDLC, review the newly-created configuration and adjust as necessary.
NTF sdlcNotification58	1.3.6.1.4.1.2007.1.4.90.2.0.58			Notification of Event SDLC.58 Message: 'Interface $1 - Configured XID/TEST timeout corrupted - fixed' Parameters list: $1: sdlc58-interface An invalid XID/TEST timeout value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the XID/TEST timeout from the SDLC config prompt for this interface.
NTF sdlcNotification59	1.3.6.1.4.1.2007.1.4.90.2.0.59			Notification of Event SDLC.59 Message: 'Interface $1 - Configured XID/TEST retry count corrupted - fixed' Parameters list: $1: sdlc59-interface An invalid XID/TEST retry value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the XID/TEST retry count from the SDLC config prompt for this interface.
NTF sdlcNotification60	1.3.6.1.4.1.2007.1.4.90.2.0.60			Notification of Event SDLC.60 Message: 'Interface $1 - Configured XID/TEST timeout value corrupted - fixed' Parameters list: $1: sdlc60-interface An invalid SNRM timeout value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the SNRM timeout from the SDLC config prompt for this interface.
NTF sdlcNotification61	1.3.6.1.4.1.2007.1.4.90.2.0.61			Notification of Event SDLC.61 Message: 'Interface $1 - Configured SNRM retry count corrupted - fixed' Parameters list: $1: sdlc61-interface An invalid SNRM retry value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the SNRM retry count from the SDLC config prompt for this interface.
NTF sdlcNotification62	1.3.6.1.4.1.2007.1.4.90.2.0.62			Notification of Event SDLC.62 Message: 'Interface $1 - Configured POLL timeout value corrupted - fixed' Parameters list: $1: sdlc62-interface An invalid POLL timeout value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the POLL timeout from the SDLC config prompt for this interface.
NTF sdlcNotification63	1.3.6.1.4.1.2007.1.4.90.2.0.63			Notification of Event SDLC.63 Message: 'Interface $1 - Configured inter-POLL delay value corrupted - fixed' Parameters list: $1: sdlc63-interface An invalid inter-POLL delay value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the inter-POLL delay from the SDLC config prompt for this interface.
NTF sdlcNotification64	1.3.6.1.4.1.2007.1.4.90.2.0.64			Notification of Event SDLC.64 Message: 'Interface $1 - Configured POLL retry count corrupted - fixed' Parameters list: $1: sdlc64-interface An invalid POLL retry value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the POLL retry count from the SDLC config prompt for this interface.
NTF sdlcNotification65	1.3.6.1.4.1.2007.1.4.90.2.0.65			Notification of Event SDLC.65 Message: 'Interface $1 - Configured inactivity timeout value corrupted - fixed' Parameters list: $1: sdlc65-interface An invalid inactivity timeout value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the inactivity timeout from the SDLC config prompt for this interface.
NTF sdlcNotification66	1.3.6.1.4.1.2007.1.4.90.2.0.66			Notification of Event SDLC.66 Message: 'Interface $1 - Configured RTS hold duration value corrupted - fixed' Parameters list: $1: sdlc66-interface An invalid RTS hold value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the RTS hold value from the SDLC config prompt for this interface.
NTF sdlcNotification67	1.3.6.1.4.1.2007.1.4.90.2.0.67			Notification of Event SDLC.67 Message: 'Interface $1 - Configured max frame size value corrupted - fixed' Parameters list: $1: sdlc67-interface An invalid maximum frame size value was detected in the link configuration, possibly due to a software upgrade. It has been temporarily changed to a valid value. To avoid this message in the future, set the maximum frame size from the SDLC config prompt for this interface.
NTF sdlcNotification68	1.3.6.1.4.1.2007.1.4.90.2.0.68			Notification of Event SDLC.68 Message: 'Interface $1 - SDLC link counters were reset by user' Parameters list: $1: sdlc68-interface The link counters have been reset from the SDLC console.
NTF sdlcNotification69	1.3.6.1.4.1.2007.1.4.90.2.0.69			Notification of Event SDLC.69 Message: 'Interface $1 - SDLC link counters cannot be reset' Parameters list: $1: sdlc69-interface The link counters could not be reset from the SDLC console. This is usually a temporary condition. Retry the operation.
NTF sdlcNotification70	1.3.6.1.4.1.2007.1.4.90.2.0.70			Notification of Event SDLC.70 Message: 'Interface $1 Link Station $2 - SDLC link counters were reset by user' Parameters list: $1: sdlc70-interface $2: sdlc70-address The user reset the counters for a remote secondary station from the SDLC console.
NTF sdlcNotification71	1.3.6.1.4.1.2007.1.4.90.2.0.71			Notification of Event SDLC.71 Message: 'Interface $1 Link Station $2 - SDLC link counters cannot be reset' Parameters list: $1: sdlc71-interface $2: sdlc71-address The user could not reset the counters for a remote secondary station from the SDLC console. This is usually a temporary condition. Retry the operation.
NTF sdlcNotification72	1.3.6.1.4.1.2007.1.4.90.2.0.72			Notification of Event SDLC.72 Message: 'Interface $1 SDLC station $2: DLC-SAP-CLOSED' Parameters list: $1: sdlc72-interface $2: sdlc72-address The remote link station has been closed by the router and is no longer active.
NTF sdlcNotification73	1.3.6.1.4.1.2007.1.4.90.2.0.73			Notification of Event SDLC.73 Message: 'Interface $1: low priority buffer request failed' Parameters list: $1: sdlc73-interface SDLC failed to allocate memory from the router's heap because it has already allocated its fair share. SDLC will recover from this usually temporary problem.
NTF sdlcNotification74	1.3.6.1.4.1.2007.1.4.90.2.0.74			Notification of Event SDLC.74 Message: 'Interface $1: high priority buffer request failed' Parameters list: $1: sdlc74-interface SDLC failed to allocate a high-priority buffer from the router's heap. As a result, SDLC will temporarily experience a loss of performance. SDLC sessions could possibly be lost if the condition persists.
NTF sdlcNotification75	1.3.6.1.4.1.2007.1.4.90.2.0.75			Notification of Event SDLC.75 Message: 'Interface $1: buffer alloc request failed, but credit is okay' Parameters list: $1: sdlc75-interface SDLC failed to allocate memory from the router's heap because the heap is exhausted. SDLC will recover from this usually temporary problem.
NTF sdlcNotification76	1.3.6.1.4.1.2007.1.4.90.2.0.76			Notification of Event SDLC.76 Message: 'Interface $1: cannot transmit I-frame. Will re-transmit later' Parameters list: $1: sdlc76-interface SDLC could not send an Information (I) frame to the interface. SDLC will attempt to re-transmit it later.
NTF sdlcNotification77	1.3.6.1.4.1.2007.1.4.90.2.0.77			Notification of Event SDLC.77 Message: 'Interface $1: cannot transmit S-frame - dropped' Parameters list: $1: sdlc77-interface SDLC could not send a Supervisory (S) frame to the interface. SDLC will attempt to re-transmit it later.
NTF sdlcNotification78	1.3.6.1.4.1.2007.1.4.90.2.0.78			Notification of Event SDLC.78 Message: 'Interface $1: cannot transmit U-frame - SDLC will recover' Parameters list: $1: sdlc78-interface SDLC could not send an Unnumbered Information (UI) frame to the interface. SDLC will attempt to re-transmit it later.
NTF sdlcNotification79	1.3.6.1.4.1.2007.1.4.90.2.0.79			Notification of Event SDLC.79 Message: 'Interface $1: cannot transmit U-frame - SDLC will re-transmit' Parameters list: $1: sdlc79-interface SDLC could not send an XID or TEST frame to the interface. SDLC will attempt to re-transmit it later.
NTF sdlcNotification80	1.3.6.1.4.1.2007.1.4.90.2.0.80			Notification of Event SDLC.80 Message: 'Interface $1: received invalid frame type - dropped' Parameters list: $1: sdlc80-interface SDLC received an invalid frame type. This frame was ignored.
NTF sdlcNotification81	1.3.6.1.4.1.2007.1.4.90.2.0.81			Notification of Event SDLC.81 Message: 'Interface $1: received a frame from a secondary station that was not polled - dropped' Parameters list: $1: sdlc81-interface SDLC received a frame from a remote link station that it had not polled. This frame was ignored. This error may also occur if the poll response timeout is too short.
NTF sdlcNotification82	1.3.6.1.4.1.2007.1.4.90.2.0.82			Notification of Event SDLC.82 Message: 'Interface $1: received a UI frame from a secondary station without the Final bit set - dropped' Parameters list: $1: sdlc82-interface SDLC received an Unnumbered Information (UI) frame without the Final (F) bit set. This frame was dropped.
NTF sdlcNotification83	1.3.6.1.4.1.2007.1.4.90.2.0.83			Notification of Event SDLC.83 Message: 'Interface $1: received a broadcast frame from a secondary station on a multipoint line - dropped' Parameters list: $1: sdlc83-interface SDLC received a frame to the broadcast address on a multipoint line. The frame was dropped.
NTF sdlcNotification84	1.3.6.1.4.1.2007.1.4.90.2.0.84			Notification of Event SDLC.84 Message: 'Interface $1: SDLC not brought up because no LINK configuration is defined' Parameters list: $1: sdlc84-interface SDLC could not be initialized because there is no SDLC link configuration for this interface.
NTF sdlcNotification85	1.3.6.1.4.1.2007.1.4.90.2.0.85			Notification of Event SDLC.85 Message: 'Interface $1: signal control request failed because $2' Parameters list: $1: sdlc85-interface $2: sdlc85-reason SDLC could not control one or more signals on the interface. This could occur if you attempt to run SDLC over an unsupported interface.
NTF sdlcNotification86	1.3.6.1.4.1.2007.1.4.90.2.0.86			Notification of Event SDLC.86 Message: 'HDX, DCD went high during HDX transmit, on interface $1' Parameters list: $1: sdlc86-interface DCD went high during transmission of a frame in half duplex mode. This is a protocol violation, and the interface will go down shortly in order to correct the problem.
NTF sdlcNotification87	1.3.6.1.4.1.2007.1.4.90.2.0.87			Notification of Event SDLC.87 Message: 'HDX, CTS now low. Premature DCD recovery complete, on interface $1' Parameters list: $1: sdlc87-interface The CTS signal has transitioned to low while the interface was recovering from a half-duplex protocol violation. The link is now in the correct state and data transfer may resume.
NTF sdlcNotification88	1.3.6.1.4.1.2007.1.4.90.2.0.88			Notification of Event SDLC.88 Message: 'HDX, unsolicited signal while idle, on interface $1' Parameters list: $1: sdlc88-interface A signal was asserted by the connected device while the line was idle. When operating in half-duplex mode, only the DTR/DSR signal should be asserted on an idle interface.
NTF sdlcNotification89	1.3.6.1.4.1.2007.1.4.90.2.0.89			Notification of Event SDLC.89 Message: 'HDX, DSR or CTS went low during HDX transmit, on interface $1' Parameters list: $1: sdlc89-interface The DSR or CTS signal went low during transmission. This is a protocol violation, and the interface will go down shortly in order to correct the problem.
NTF sdlcNotification90	1.3.6.1.4.1.2007.1.4.90.2.0.90			Notification of Event SDLC.90 Message: 'Interface $1: received inappropriate frame while closing link $2 - dropped' Parameters list: $1: sdlc90-interface $2: sdlc90-address SDLC received a frame other than a UA while trying to close the link station. The router ignored this frame.
NTF sdlcNotification91	1.3.6.1.4.1.2007.1.4.90.2.0.91			Notification of Event SDLC.91 Message: 'Secondary station $1 has been dynamically added, on interface $2' Parameters list: $1: sdlc91-address $2: sdlc91-interface An SDLC remote link station was added by the user from the SDLC console and is now available for use.
NTF sdlcNotification92	1.3.6.1.4.1.2007.1.4.90.2.0.92			Notification of Event SDLC.92 Message: 'Secondary station $1 has been dynamically deleted, on interface $2' Parameters list: $1: sdlc92-address $2: sdlc92-interface An SDLC remote link station was deleted by the user from the SDLC console and is no longer available for use.
NTF sdlcNotification93	1.3.6.1.4.1.2007.1.4.90.2.0.93			Notification of Event SDLC.93 Message: 'Interface $1: received a frame from an invalid station address - dropped' Parameters list: $1: sdlc93-interface SDLC received a frame from a remote link station that contains an unrecognized station address. The router ignored this frame.
NTF sdlcNotification94	1.3.6.1.4.1.2007.1.4.90.2.0.94			Notification of Event SDLC.94 Message: 'Interface $1 Link Station $2 - station is disabled; frame ignored' Parameters list: $1: sdlc94-interface $2: sdlc94-address The router ignored the received frame for this station, because the target station is in a disabled state.
NTF sdlcNotification95	1.3.6.1.4.1.2007.1.4.90.2.0.95			Notification of Event SDLC.95 Message: 'Interface $1 SDLC station $2: DLC-RX-NXID-WHILE-IN-NRM' Parameters list: $1: sdlc95-interface $2: sdlc95-address The local SDLC secondary link station received a null XID frame from a remote link station while in NRM. We treat this as an indication that the link failed at the sending end and this is an attempt to reestablish the connection.

RFC description

Manages SNMP notifications generated by the SDLC event subsystem in Teldat routers.

Start monitoring Teldat router with legacy SDLC/SNA interface module (link-level state event traps) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TELDAT-TRAP-SDLC-MIB

What Is TELDAT-TRAP-SDLC-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description