All MIBs › TAVVE-MIB
Category: Network Management Infrastructure, Vendor-Specific Device Management
Description: Manages Tavve network management device configuration and SNMP proxy service state.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TAVVE-MIB?
TAVVE-MIB is the vendor-specific MIB for Tavve Software's network management/SNMP-proxy products, used historically to relay events (via an "EventWatch"/tscEw object family) between managed devices and upstream network management platforms. It exposes fault and event data describing a source device's identity, address, protocol, and associated fault conditions, along with threshold/SLA-value settings and a report-host destination for forwarding alerts. Rather than exposing hardware sensors of its own, this MIB is primarily used to monitor the fault/event status of other devices proxied through the Tavve system, tracking fault names and times and user-defined thresholds that indicate degraded service levels elsewhere in the network. Because it wraps or forwards information sourced from other devices' protocols (referenced generically via tscEwSourceProtocol), it depends contextually on whatever protocol/MIB the monitored source device uses rather than a single fixed standard. Typical deployment is a service-provider or enterprise NOC where Tavve's software acts as an SNMP proxy/aggregation layer for fault and SLA event correlation across many managed elements. Engineers can download the TAVVE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TAVVE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Tavve network management/SNMP proxy appliance
Monitoring Examples
An operator would poll tscEwFaultName and tscEwFaultTimes to see how often and when a monitored source device (identified by tscEwSourceNode/tscEwSourceAddr) has raised a fault. tscEwUserThreshold and tscEwSlaValue let the admin read or set an SLA breach threshold, flagging when a metric exceeds an agreed limit. tscEwReportHost identifies where these fault events get forwarded, useful for confirming alert routing is correctly configured to the NOC's collector.
What Can Be Monitored
- source node fault status
- fault occurrence timestamps
- fault source protocol
- user-defined alert thresholds
- SLA metric value
- alert report destination host
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString |
From RFC1286-MIB
| MacAddress |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| tavve | 1.3.6.1.4.1.2668 | |||
| traps | 1.3.6.1.4.1.2668.1 | |||
| products | 1.3.6.1.4.1.2668.1.1 | |||
| eventWatch | 1.3.6.1.4.1.2668.1.1.1 | |||
| NTF tscEwSourceDown | 1.3.6.1.4.1.2668.1.1.1.0.1 | Device is verified down. This trap is sent after EventWatch verifies a device is down and it is not correlated to a problem in the network. This trap configured with source-down-trap. The bound variables contain the address of the fault, its name, and its protocol. | ||
| NTF tscEwInferredDown | 1.3.6.1.4.1.2668.1.1.1.0.2 | Device is verified down. This trap is sent after EventWatch verifies a device is down and it is not correlated to a problem in the network. This trap configured with behind-down-trap. | ||
| NTF tscEwSourceUp | 1.3.6.1.4.1.2668.1.1.1.0.3 | Device is back up. This trap complements trap 1 to report that the source node is back up. This trap configured with source-up-trap. | ||
| NTF tscEwInferredUp | 1.3.6.1.4.1.2668.1.1.1.0.4 | Device is verified up. This trap complements trap 2 to report that the root cause node is back up. This trap configured with behind-up-trap. | ||
| NTF tscEwNodeDown | 1.3.6.1.4.1.2668.1.1.1.0.5 | Device is verified down. This trap is issued when EventWatch is reporting the node down. Note this is the root cause node. This trap configured with level/trap. | ||
| NTF tscEwNodeUp | 1.3.6.1.4.1.2668.1.1.1.0.6 | Device is back up after being verified down. This trap configured with level/trap. | ||
| NTF tscEwSlaThres | 1.3.6.1.4.1.2668.1.1.1.0.7 | The availability of this group or host fell below the user configured threshold. This trap configured with level/trap. | ||
| NTF tscEwRemoteSourceDown | 1.3.6.1.4.1.2668.1.1.1.0.11 | Device is verified down by Remote. This trap is sent after EventWatch on Remote verifies a device is down and it is not correlated to a problem in the network. This trap configured with source-down-trap. The bound variables contain the address of the fault, its name, and its protocol. | ||
| NTF tscEwRemoteInferredDown | 1.3.6.1.4.1.2668.1.1.1.0.12 | Device is verified down by Remote. This trap is sent after EventWatch on Remote verifies a device is down and it is not correlated to a problem in the network. This trap configured with behind-down-trap. | ||
| NTF tscEwRemoteSourceUp | 1.3.6.1.4.1.2668.1.1.1.0.13 | Device is back up, reported by Remote. This trap complements trap 1 to report that the source node is back up on Remote. This trap configured with source-up-trap. | ||
| NTF tscEwRemoteInferredUp | 1.3.6.1.4.1.2668.1.1.1.0.14 | Device is verified up by Remote. This trap complements trap 2 to report that the root cause node is back up on Remote. This trap configured with behind-up-trap. | ||
| NTF tscEwRemoteNodeDown | 1.3.6.1.4.1.2668.1.1.1.0.15 | Device is verified down by Remote. This trap is issued when EventWatch is reporting the node down. Note this is the root cause node. This trap configured with level/trap. | ||
| NTF tscEwRemoteNodeUp | 1.3.6.1.4.1.2668.1.1.1.0.16 | Device is back up after being verified down by Remote. This trap configured with level/trap. | ||
| NTF tscEwTestTrap | 1.3.6.1.4.1.2668.1.1.1.0.91 | EventWatch Test Notification. This trap is sent to EventWatch. It is used to verify that EventWatch can receive and send traps. This trap configured with test-trap. The bound variables contain the address of the device, its name, and its protocol. | ||
| NTF tscEwTestTrapRecv | 1.3.6.1.4.1.2668.1.1.1.0.92 | EventWatch Test Notification. This trap is sent after EventWatch receives it. The status of the device reported is not actually verified. This trap configured with test-trap. The bound variables contain the address of the device, its name, and its protocol. | ||
| STR tscEwSourceNode | 1.3.6.1.4.1.2668.1.1.1.1 | DisplayString | read-only | The address of the node that was originally reported down. |
| STR tscEwFaultAddr | 1.3.6.1.4.1.2668.1.1.1.2 | DisplayString | read-only | The IP address of the node that was is the root cause. |
| STR tscEwFaultTimes | 1.3.6.1.4.1.2668.1.1.1.3 | DisplayString | read-only | A string with two time stamps in it: 1) the current time 2) the time the original failure was reported The time is printed in Unix time (seconds since Jan 1, 1970). |
| STR tscEwSourceAddr | 1.3.6.1.4.1.2668.1.1.1.6 | DisplayString | read-only | The address of the node being reported. |
| STR tscEwGroupName | 1.3.6.1.4.1.2668.1.1.1.7 | DisplayString | read-only | The group name (as defined to EventWatch to which this node belongs. |
| STR tscEwSourceName | 1.3.6.1.4.1.2668.1.1.1.8 | DisplayString | read-only | The name of the node being reported. |
| STR tscEwSourceProtocol | 1.3.6.1.4.1.2668.1.1.1.9 | DisplayString | read-only | The protocol of the node being reported, e.g. IP. |
| STR tscEwFaultName | 1.3.6.1.4.1.2668.1.1.1.10 | DisplayString | read-only | The name of the fault being reported. |
| STR tscEwFaultProtocol | 1.3.6.1.4.1.2668.1.1.1.11 | DisplayString | read-only | The protocol of the fault being reported, e.g. IP. |
| INT tscEwUserThreshold | 1.3.6.1.4.1.2668.1.1.1.12 | INTEGER | read-only | The value of the user defined threshold. |
| INT tscEwSlaValue | 1.3.6.1.4.1.2668.1.1.1.13 | INTEGER | read-only | The value of the group availability. |
| STR tscEwReportHost | 1.3.6.1.4.1.2668.1.1.1.14 | DisplayString | read-only | The name of the EventWatch host reporting the problem. Make sure all the Remote box names are resolvable. |
| INT tscEwDownTime | 1.3.6.1.4.1.2668.1.1.1.15 | INTEGER | read-only | The amount of time (in seconds) the device in question was down. |
| INT tscEwEventTime | 1.3.6.1.4.1.2668.1.1.1.16 | INTEGER | read-only | The time (Unix time) when this event occurred. |
| STR tscEwDescr | 1.3.6.1.4.1.2668.1.1.1.17 | DisplayString | read-only | The textual description of the entity. |
| tcpdmon | 1.3.6.1.4.1.2668.1.1.2 | |||
| STR tscTcpSourceNode | 1.3.6.1.4.1.2668.1.1.2.1 | DisplayString | read-only | The address of the node on which the TCP reported. |
| STR tscTCPPortName | 1.3.6.1.4.1.2668.1.1.2.2 | DisplayString | read-only | The Service Name of this particular port. |
| STR tscTCPPortNumber | 1.3.6.1.4.1.2668.1.1.2.3 | DisplayString | read-only | The Service Number of this particular port. |
| STR tscTCPTime | 1.3.6.1.4.1.2668.1.1.2.4 | DisplayString | read-only | The time at which the event occurred. |
| ciscotrap | 1.3.6.1.4.1.2668.1.1.3 | |||
| NTF tscCtSeverity0 | 1.3.6.1.4.1.2668.1.1.3.0.10 | Cisco device reporting a severity 0 event. | ||
| NTF tscCtSeverity1 | 1.3.6.1.4.1.2668.1.1.3.0.11 | Cisco device reporting a severity 1 event. | ||
| NTF tscCtSeverity2 | 1.3.6.1.4.1.2668.1.1.3.0.12 | Cisco device reporting a severity 2 event. | ||
| NTF tscCtSeverity3 | 1.3.6.1.4.1.2668.1.1.3.0.13 | Cisco device reporting a severity 3 event. | ||
| NTF tscCtSeverity4 | 1.3.6.1.4.1.2668.1.1.3.0.14 | Cisco device reporting a severity 4 event. | ||
| NTF tscCtSeverity5 | 1.3.6.1.4.1.2668.1.1.3.0.15 | Cisco device reporting a severity 5 event. | ||
| NTF tscCtSeverity6 | 1.3.6.1.4.1.2668.1.1.3.0.16 | Cisco device reporting a severity 6 event. | ||
| NTF tscCtSeverity7 | 1.3.6.1.4.1.2668.1.1.3.0.17 | Cisco device reporting a severity 7 event. | ||
| NTF tscCtSeverity8 | 1.3.6.1.4.1.2668.1.1.3.0.18 | Cisco device reporting a severity 8 event. | ||
| STR tscCtLogMessage | 1.3.6.1.4.1.2668.1.1.3.1 | DisplayString | read-only | The message from log file suitable for logging. Format is: month day, time : facility-severity-mnemonic: message |
| STR tscCtFacility | 1.3.6.1.4.1.2668.1.1.3.2 | DisplayString | read-only | The Cisco facility from log message, e.g. IP, PIX. |
| STR tscCtSeverity | 1.3.6.1.4.1.2668.1.1.3.3 | DisplayString | read-only | The Cisco severity from log message, e.g. 0, 1, 2, 3, 4, 5, 6, 7, 8. |
| STR tscCtMnemonic | 1.3.6.1.4.1.2668.1.1.3.4 | DisplayString | read-only | The Cisco Mnemonic from log message, e.g. DUPADDR. |
| STR tscCtMessage | 1.3.6.1.4.1.2668.1.1.3.5 | DisplayString | read-only | The Cisco message from log message (stripped of time stamp, facility, severity, mnemonic |
| wwwmon | 1.3.6.1.4.1.2668.1.1.4 | |||
| NTF wwwmonUp | 1.3.6.1.4.1.2668.1.1.4.0.101 | Wwwmon reporting the status change to Up from a web page query. | ||
| NTF wwwmonTimeout | 1.3.6.1.4.1.2668.1.1.4.0.102 | Wwwmon reporting the status change to Timeout from a web page query. | ||
| NTF wwwmonRefd | 1.3.6.1.4.1.2668.1.1.4.0.103 | Wwwmon reporting the status change to Refused from a web page query. | ||
| NTF wwwmonUnknown | 1.3.6.1.4.1.2668.1.1.4.0.104 | Wwwmon reporting the status change to Unknown from a web page query. | ||
| NTF wwwmonBusy | 1.3.6.1.4.1.2668.1.1.4.0.105 | Wwwmon reporting the status change to Busy from a web page query. | ||
| NTF wwwmonInfo | 1.3.6.1.4.1.2668.1.1.4.0.106 | Wwwmon reporting the status change to HTTP-Info from a web page query. | ||
| NTF wwwmonRedirect | 1.3.6.1.4.1.2668.1.1.4.0.107 | Wwwmon reporting the status change to HTTP-Redirect from a web page query. | ||
| NTF wwwmonClient | 1.3.6.1.4.1.2668.1.1.4.0.108 | Wwwmon reporting the status change to HTTP-Client-Err from a web page query. | ||
| NTF wwwmonServer | 1.3.6.1.4.1.2668.1.1.4.0.109 | Wwwmon reporting the status change to HTTP-Server-Err from a web page query. | ||
| STR wwwmonServerName | 1.3.6.1.4.1.2668.1.1.4.1 | DisplayString | read-only | This is the web server's hostname |
| INT wwwmonServerPort | 1.3.6.1.4.1.2668.1.1.4.2 | INTEGER | read-only | This is the web server port number. |
| STR wwwmonServerURL | 1.3.6.1.4.1.2668.1.1.4.3 | DisplayString | read-only | This is the URL passed to the web server |
| STR wwwmonServerStatus | 1.3.6.1.4.1.2668.1.1.4.4 | DisplayString | read-only | This is the web server's status for the HEAD request. |
| agentmon | 1.3.6.1.4.1.2668.1.1.5 | |||
| remote | 1.3.6.1.4.1.2668.1.1.6 | |||
| NTF tscIfDown | 1.3.6.1.4.1.2668.1.1.6.0.1 | Interface is not reachable. This trap is sent after tpingd determines that an interface is no longer reachable. The bound variables contain the address of the device. | ||
| NTF tscIfUp | 1.3.6.1.4.1.2668.1.1.6.0.2 | Interface is reachable. This trap is sent after tpingd determines that an interface is now reachable. The bound variables contain the address of the device. | ||
| NTF tscIfLatThreshold | 1.3.6.1.4.1.2668.1.1.6.0.3 | A user-defined interface latency threshold was exceeded. This trap is sent after tpingd determines that a user-defined interface latency threshold was exceeded for this device. The bound variables contain the address of the device, the value of the interface latency, the value of the user-defined threshold. | ||
| NTF tscIfLatRearm | 1.3.6.1.4.1.2668.1.1.6.0.4 | A user-defined interface latency threshold was rearmed. This trap is sent after tpingd determines that a user-defined interface latency threshold was rearmed for this device. The bound variables contain the address of the device, the value of the interface latency, the value of the user-defined rearm. | ||
| NTF tscIfUnknown | 1.3.6.1.4.1.2668.1.1.6.0.5 | Interface status is unknown. This trap is sent after tpingd determines that an interface is no longer known. The bound variables contain the address of the device. | ||
| NTF tscNodeDown | 1.3.6.1.4.1.2668.1.1.6.0.6 | Node is down. This trap is sent after ipmon determines that all interfaces on a node are down. The bound variables contain the address of the device. | ||
| NTF tscNodeMarginal | 1.3.6.1.4.1.2668.1.1.6.0.7 | Node is marginal. This trap is sent after ipmon determines that some interfaces on the node are down and some interfaces on the node are up. The bound variables contain the address of the device. | ||
| NTF tscNodeUp | 1.3.6.1.4.1.2668.1.1.6.0.8 | Node is up. This trap is sent after ipmon determines that all interfaces on a node are up. The bound variables contain the address of the device. | ||
| NTF tscNodeUnknown | 1.3.6.1.4.1.2668.1.1.6.0.9 | Node is unknown. This trap is sent after ipmon determines that all interfaces on a node are unknown. The bound variables contain the address of the device. | ||
| NTF tscNewNode | 1.3.6.1.4.1.2668.1.1.6.0.10 | A new node has been discovered by this system. | ||
| NTF tscNameChange | 1.3.6.1.4.1.2668.1.1.6.0.11 | A node name has changed | ||
| NTF tscIfDelete | 1.3.6.1.4.1.2668.1.1.6.0.12 | Interface is deleted This trap is sent after tpingd determines that an interface has been deleted. The bound variables contain the address of the device. | ||
| NTF tscNodeAdded | 1.3.6.1.4.1.2668.1.1.6.0.13 | Node is added. This trap is sent when scannode determines that a node is new in the nodedb. | ||
| NTF tscInterfaceAdded | 1.3.6.1.4.1.2668.1.1.6.0.14 | An interface on a node is added. This trap is sent when scannode determines that an interface is new in the ifdb. | ||
| NTF tscNodeDeleted | 1.3.6.1.4.1.2668.1.1.6.0.15 | Node is deleted. This trap is sent when scannode determines that a node is removed from the nodedb. | ||
| NTF tscInterfaceDeleted | 1.3.6.1.4.1.2668.1.1.6.0.16 | An interface on a node is removed. This trap is sent when scannode determines that an interface is removed from the ifdb. | ||
| NTF tscHostnameChanged | 1.3.6.1.4.1.2668.1.1.6.0.17 | A hostname change has been detected. This trap is sent when scannode determines that a new hostname is being used for a formerly different named node. | ||
| NTF tscSysObjectIDChanged | 1.3.6.1.4.1.2668.1.1.6.0.18 | The sysObjectID on the device changed. This trap is sent when scannode determines that a new sysObjectID was detected for a host. | ||
| NTF tscProcFail | 1.3.6.1.4.1.2668.1.1.6.0.21 | A key eProbe process has failed. | ||
| NTF tscProcStop | 1.3.6.1.4.1.2668.1.1.6.0.22 | A key eProbe process has stopped (deliberate). | ||
| NTF tscProcStart | 1.3.6.1.4.1.2668.1.1.6.0.23 | A key eProbe process has started. | ||
| NTF tscFsFull | 1.3.6.1.4.1.2668.1.1.6.0.24 | A file system is getting full. It has reached a particular level of capacity (%). | ||
| NTF tscVoidWarranty | 1.3.6.1.4.1.2668.1.1.6.0.25 | The eProbe admin has elected for root access to the device and understands this voids the warranty. | ||
| NTF tscSysNameChanged | 1.3.6.1.4.1.2668.1.1.6.0.26 | The sysName on the device changed. This trap is sent when scannode determines that a new sysName was detected for a host. | ||
| NTF tscSysDescrChanged | 1.3.6.1.4.1.2668.1.1.6.0.27 | The sysDescr on the device changed. This trap is sent when scannode determines that a new sysDescr was detected for a host. | ||
| NTF tscSysLocationChanged | 1.3.6.1.4.1.2668.1.1.6.0.28 | The sysLocation on the device changed. This trap is sent when scannode determines that a new sysLocation was detected for a host. | ||
| NTF tscSysContactChanged | 1.3.6.1.4.1.2668.1.1.6.0.29 | The sysContact on the device changed. This trap is sent when scannode determines that a new sysContact was detected for a host. | ||
| NTF tscManage | 1.3.6.1.4.1.2668.1.1.6.0.50 | A node is now managed. This trap is sent after tmanage switches the status of the node to managed. The bound variable contain the name of the device. | ||
| NTF tscUnmanage | 1.3.6.1.4.1.2668.1.1.6.0.51 | A node is now unmanaged. This trap is sent after tunmanage switches the status of the node to unmanaged. The bound variable contain the name of the device. | ||
| NTF tscIfManage | 1.3.6.1.4.1.2668.1.1.6.0.52 | An interface is now managed. This trap is sent after tmanage switches the status of the interface to managed. The bound variables contain the ifIndex, ifDescr. | ||
| NTF tscIfUnmanage | 1.3.6.1.4.1.2668.1.1.6.0.53 | An interface is now unmanaged. This trap is sent after tunmanage switches the status of the interface to unmanaged. The bound variables contain the ifIndex, ifDescr. | ||
| NTF tscNetManage | 1.3.6.1.4.1.2668.1.1.6.0.54 | A subnet is now managed. This trap is sent after tmanage switches the status of the subnet to managed. | ||
| NTF tscNetUnmanage | 1.3.6.1.4.1.2668.1.1.6.0.55 | A subnet is now unmanaged. This trap is sent after tunmanage switches the status of the subnet to unmanaged. | ||
| NTF tscPortManage | 1.3.6.1.4.1.2668.1.1.6.0.56 | An interface is now managed. This trap is sent after tmanage switches the status of the interface to managed. The bound variables contain the ifIndex, chassis, slot, and positon. | ||
| NTF tscPortUnmanage | 1.3.6.1.4.1.2668.1.1.6.0.57 | An interface is now unmanaged. This trap is sent after tunmanage switches the status of the interface to unmanaged. The bound variables contain the ifIndex, chassis, slot, and positon. | ||
| NTF tscFwdTrap | 1.3.6.1.4.1.2668.1.1.6.0.60 | Ensapsulate a trap within this trap. This trap is sent by ePROBE when forwarding traps with ensapsulation mode on. In particular, this makes sure forwarded traps do not have source agent IP address which messes up the NMS in duplicate IP environments. The bound variables contain the details of the oringal trap: agent IP address, agent hostname, enterprise OID, generic, specific, timestamp, community, log message, and variables. | ||
| NTF tscRedPeerAdd | 1.3.6.1.4.1.2668.1.1.6.0.61 | Report a redundant peer has been added. | ||
| NTF tscRedPeerRm | 1.3.6.1.4.1.2668.1.1.6.0.62 | Report a redundant peer has been removed. | ||
| NTF tscRedPeerUp | 1.3.6.1.4.1.2668.1.1.6.0.63 | Report a redundant peer is now up. | ||
| NTF tscRedPeerUnavail | 1.3.6.1.4.1.2668.1.1.6.0.64 | Report a redundant peer is now unavailable. | ||
| NTF tscRedPeerDown | 1.3.6.1.4.1.2668.1.1.6.0.65 | Report a redundant peer is now down. | ||
| NTF tscRemoteNoStatus | 1.3.6.1.4.1.2668.1.1.6.0.68 | ePROBE is inferred down because it has not reported in to NMS. This trap is sent by ePdaemon. This trap has bindings in alignment with remote source down trap | ||
| NTF tscRemoteAlive | 1.3.6.1.4.1.2668.1.1.6.0.69 | ePROBE is inferred up because it has again reported in to NMS. This trap is sent by ePdaemon. This trap has bindings in alignment with remote source up trap | ||
| STR tscRemoteSourceNode | 1.3.6.1.4.1.2668.1.1.6.1 | DisplayString | read-only | The hostname of the node being reported. |
| INT tscRemoteValue | 1.3.6.1.4.1.2668.1.1.6.2 | INTEGER | read-only | The value of a variable a thresold was set against. |
| INT tscRemoteThreshold | 1.3.6.1.4.1.2668.1.1.6.3 | INTEGER | read-only | The value of a user-defined thresold. |
| INT tscRemoteRearm | 1.3.6.1.4.1.2668.1.1.6.4 | INTEGER | read-only | The value of a user-defined rearm. |
| STR tscRemoteSourceAddr | 1.3.6.1.4.1.2668.1.1.6.5 | DisplayString | read-only | The address of the node being reported. |
| STR tscRemoteName | 1.3.6.1.4.1.2668.1.1.6.6 | DisplayString | read-only | The hostname of this reporting system. |
| STR tscRemoteSourceNode2 | 1.3.6.1.4.1.2668.1.1.6.7 | DisplayString | read-only | Another hostname being reported. |
| STR tscRemoteSourceProtocol | 1.3.6.1.4.1.2668.1.1.6.8 | DisplayString | read-only | The network protocol of the node being reported. |
| STR tscRemoteProcName | 1.3.6.1.4.1.2668.1.1.6.9 | DisplayString | read-only | The eProbe process name being reported. |
| STR tscRemoteFsDevice | 1.3.6.1.4.1.2668.1.1.6.10 | DisplayString | read-only | The file system logical device. |
| STR tscRemoteFsName | 1.3.6.1.4.1.2668.1.1.6.11 | DisplayString | read-only | The file system name (mount point). |
| STR tscRemoteIfIndex | 1.3.6.1.4.1.2668.1.1.6.12 | DisplayString | read-only | The relevant ifIndex. |
| STR tscRemoteChassis | 1.3.6.1.4.1.2668.1.1.6.13 | DisplayString | read-only | The relevant chassis #. |
| STR tscRemoteSlot | 1.3.6.1.4.1.2668.1.1.6.14 | DisplayString | read-only | The relevant slot #. |
| STR tscRemotePosition | 1.3.6.1.4.1.2668.1.1.6.15 | DisplayString | read-only | The relevant port position #. |
| STR tscRemoteDescription | 1.3.6.1.4.1.2668.1.1.6.16 | DisplayString | read-only | The relevant description. |
| STR tscRemoteRecno | 1.3.6.1.4.1.2668.1.1.6.17 | DisplayString | read-only | The relevant database record number. |
| INT tscRemoteOldValue | 1.3.6.1.4.1.2668.1.1.6.18 | INTEGER | read-only | The old value of a variable a thresold was set against. |
| STR tscRemoteTrapOID | 1.3.6.1.4.1.2668.1.1.6.19 | DisplayString | read-only | The enterprise OID of trap being encapsulated. |
| STR tscRemoteTrapGeneric | 1.3.6.1.4.1.2668.1.1.6.20 | DisplayString | read-only | The generic of trap being encapsulated. |
| STR tscRemoteTrapSpecific | 1.3.6.1.4.1.2668.1.1.6.21 | DisplayString | read-only | The specific of trap being encapsulated. |
| STR tscRemoteTrapTimestamp | 1.3.6.1.4.1.2668.1.1.6.22 | DisplayString | read-only | The timestamp of trap being encapsulated. |
| STR tscRemoteTrapCommunity | 1.3.6.1.4.1.2668.1.1.6.23 | DisplayString | read-only | The community of trap being encapsulated. |
| STR tscRemoteTimestamp | 1.3.6.1.4.1.2668.1.1.6.24 | DisplayString | read-only | A timestamp for this event. |
| STR tscRemoteDomain | 1.3.6.1.4.1.2668.1.1.6.25 | DisplayString | read-only | An ePROBE domain for this event. |
| _pysmi_global | 1.3.6.1.4.1.2668.1.1.7 | |||
| portmon | 1.3.6.1.4.1.2668.1.1.8 | |||
| NTF tscPmNameChange | 1.3.6.1.4.1.2668.1.1.8.0.1 | The port name has changed. This trap is sent after a port configuration check determined that the port name has changed. | ||
| NTF tscPmTypeChange | 1.3.6.1.4.1.2668.1.1.8.0.2 | The port type has changed. This trap is sent after a port configuration check determined that the port type has changed. | ||
| NTF tscPmSpeedChange | 1.3.6.1.4.1.2668.1.1.8.0.3 | The port speed has changed. This trap is sent after a port configuration check determined that the port speed has changed. | ||
| NTF tscPmDuplexChange | 1.3.6.1.4.1.2668.1.1.8.0.4 | The port duplex has changed. This trap is sent after a port configuration check determined that the port duplex has changed. | ||
| NTF tscPmVlanChange | 1.3.6.1.4.1.2668.1.1.8.0.5 | The port VLAN has changed. This trap is sent after a port configuration check determined that the port VLAN has changed. | ||
| NTF tscPmNewPort | 1.3.6.1.4.1.2668.1.1.8.0.100 | A new port has been discovered. This trap is sent after a port configuration check determined that a new port is present | ||
| NTF tscPmPortFault | 1.3.6.1.4.1.2668.1.1.8.0.101 | The status of a port has gone critical. This trap is sent after a port status check determined that the port is not functioning. | ||
| NTF tscPmPortRestored | 1.3.6.1.4.1.2668.1.1.8.0.102 | The status of a port returned to normal. This trap is sent after a port status check determined that the port is functioning again. | ||
| NTF tscPmPortUnknown | 1.3.6.1.4.1.2668.1.1.8.0.103 | The status of a port is now unknown. This trap is sent after a port status check determined that the port has entered an unknown state. | ||
| NTF tscPmPortDeleted | 1.3.6.1.4.1.2668.1.1.8.0.104 | A port has been deleted from portdb. This trap is sent after a port status check determined that the port no longer exists. | ||
| STR tscPmOldValue | 1.3.6.1.4.1.2668.1.1.8.1 | DisplayString | read-only | The old value (before the change). |
| STR tscPmValue | 1.3.6.1.4.1.2668.1.1.8.2 | DisplayString | read-only | The (new) value (after the change). |
| INT tscPmIndex | 1.3.6.1.4.1.2668.1.1.8.3 | INTEGER | read-only | The ifIndex for the port being reported. |
| INT tscPmChassis | 1.3.6.1.4.1.2668.1.1.8.4 | INTEGER | read-only | The chassis # for the port being reported. |
| INT tscPmSlot | 1.3.6.1.4.1.2668.1.1.8.5 | INTEGER | read-only | The slot number inside chassis for the port being reported. |
| INT tscPmPos | 1.3.6.1.4.1.2668.1.1.8.6 | INTEGER | read-only | The port # or port position in slot for the port being reported. |
| STR tscPmStatus | 1.3.6.1.4.1.2668.1.1.8.7 | DisplayString | read-only | The (new) status of the port. |
| STR tscPmName | 1.3.6.1.4.1.2668.1.1.8.8 | DisplayString | read-only | The user defined name of the port. |
| STR tscPmTime | 1.3.6.1.4.1.2668.1.1.8.9 | DisplayString | read-only | The (Unix) time of the status change. |
| syslogtrap | 1.3.6.1.4.1.2668.1.1.9 | |||
| NTF tscSltTrap | 1.3.6.1.4.1.2668.1.1.9.0.1 | Reporting a syslog event. | ||
| STR tscSltLogMessage | 1.3.6.1.4.1.2668.1.1.9.1 | DisplayString | read-only | The message from log file suitable for logging. Format is: month day time host facility[pid]: message |
| STR tscSltFacility | 1.3.6.1.4.1.2668.1.1.9.2 | DisplayString | read-only | The facility from log message, e.g. snmpd, kernel. |
| INT tscSltPid | 1.3.6.1.4.1.2668.1.1.9.3 | INTEGER | read-only | The process id of the facility or 0. |
| STR tscSltHostname | 1.3.6.1.4.1.2668.1.1.9.4 | DisplayString | read-only | The hostname of the device reporting the message. |
| STR tscSltMessage | 1.3.6.1.4.1.2668.1.1.9.5 | DisplayString | read-only | The message from log message (stripped of time stamp, facility, and hostname |
| atmmon | 1.3.6.1.4.1.2668.1.1.10 | |||
| NTF tscAtmIfDown | 1.3.6.1.4.1.2668.1.1.10.0.101 | Interface is not reachable. This trap is sent after atmmon determines that an interface is no longer reachable. The bound variables contain the address of the device. | ||
| NTF tscAtmIfUp | 1.3.6.1.4.1.2668.1.1.10.0.102 | Interface is reachable. This trap is sent after atmmon determines that an interface is reachable. The bound variables contain the address of the device. | ||
| NTF tscAtmIfUnknown | 1.3.6.1.4.1.2668.1.1.10.0.103 | Interface is not reachable. This trap is sent after atmmon determines that an interface is no longer reachable. The bound variables contain the address of the device. | ||
| STR tscAtmmonSourceNode | 1.3.6.1.4.1.2668.1.1.10.1 | DisplayString | read-only | The hostname of the interface being reported. |
| INT tscAtmmonIfIndex | 1.3.6.1.4.1.2668.1.1.10.2 | INTEGER | read-only | The relevant ifIndex. |
| STR tscAtmmonifName | 1.3.6.1.4.1.2668.1.1.10.3 | DisplayString | read-only | The name of the interface being reported down. |
| xmon | 1.3.6.1.4.1.2668.1.1.12 | |||
| custom | 1.3.6.1.4.1.2668.1.2 | |||
| agents | 1.3.6.1.4.1.2668.2 |
RFC description
Manages traps and monitoring for Tavve Software products including EventWatch and network monitoring.
Start monitoring Tavve network management/SNMP proxy appliance (proxied fault/event/SLA status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.