All MIBs › SWITCH-SYSTEM-MIB
Organization: Raisecom Science & Technology Co., ltd
Last Updated: 2004-12-17
Category: Switch Management - Raisecom
Description: Manages Raisecom switch system-level objects including identity, uptime, and operational configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SWITCH-SYSTEM-MIB?
SWITCH-SYSTEM-MIB is a Raisecom enterprise MIB module (prefix rc) covering system-level management of the iSCOM Ethernet switch product family. It exposes system identity and capability data such as hardware and internal software (RoseVersion) versions, maximum port/aggregation/subnet capacities, MAC address table sizing, VLAN space, and per-slot hardware information, all reachable via the SWITCH-SYSTEM-MIB OID tree defined under the rc enterprise prefix. It is squarely a hardware/software status module: it surfaces hardware and firmware version strings, the most recent internal error code, and slot-level hardware inventory, all of which are useful for detecting a failed line card or confirming firmware consistency before an upgrade. No explicit dependency on other MIBs is evident from the source, though it likely complements standard interface and VLAN MIBs used alongside it on the same switch. It is typically deployed on Raisecom iSCOM-series metro Ethernet access/aggregation switches in carrier and enterprise networks.
IPNetwork Monitor allows you to monitor SNMP objects defined in SWITCH-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Raisecom iSCOM-series metro Ethernet switch family (system identity/hardware inventory)
Monitoring Examples
rcSwitchHardwareVersion and rcSwitchRoseVersion let an admin confirm which hardware revision and internal software version are running before a firmware rollout; rcSwitchLastErrorCode exposes the most recent internal fault code, and rcSlotInformation/rcSwitchInformation reveal per-slot hardware presence, useful for detecting a missing or failed line card; rcSwitchMacTableCapability and rcSwitchVlanSpaceSize expose configured capacity limits for the MAC table and VLAN space.
What Can Be Monitored
- hardware and software version
- last error code
- slot/card inventory
- MAC address table capacity
- VLAN space utilization
- max port/aggregation capacity
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifIndex | OBJECT-TYPE |
From RAISECOM-BASE-MIB
| iscomSwitch | OBJECT-IDENTITY |
From SNMPv2-CONF
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| MacAddress | |
| RowStatus | |
| TruthValue |
From SWITCH-TC
| EnableVar | |
| PortList | |
| Vlanset |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| I32 rcArpAgingTime | 1.3.6.1.4.1.8886.6.1.1.3.16 | Integer32 | read-write | arp timeout |
| POR rcBpduTransPorts | 1.3.6.1.4.1.8886.6.1.1.3.17 | PortList | read-write | The ports translating BPDU packets. |
| INT rcComboIndex | 1.3.6.1.4.1.8886.6.1.1.4.2.1.1 | INTEGER | not-accessible | An index based 1 that uniquely identifies a Ether like interface. |
| INT rcComboPortActiveStatus | 1.3.6.1.4.1.8886.6.1.1.4.2.1.5 | INTEGER | read-only | used to identify whether this Combo port currently be in the active state. |
| rcComboPortEntry | 1.3.6.1.4.1.8886.6.1.1.4.2.1 | not-accessible | Table entry for Combo port status information. | |
| INT rcComboPortIndex | 1.3.6.1.4.1.8886.6.1.1.4.2.1.2 | INTEGER | not-accessible | An index for media attachment on Combo that 'rcComboIndex' uniquely identifies a Ether like interface. |
| INT rcComboPortMediaAttachCapability | 1.3.6.1.4.1.8886.6.1.1.4.2.1.6 | INTEGER | read-only | Medium type and capability of media attachment units. It is different with rcComboPortType which identifys the capability of the Ether like interface |
| INT rcComboPortMediaAttachType | 1.3.6.1.4.1.8886.6.1.1.4.2.1.4 | INTEGER | read-only | media attachment type of Combo port. |
| rcComboPortTable | 1.3.6.1.4.1.8886.6.1.1.4.2 | not-accessible | A table of Combo port and associated properties. | |
| INT rcComboPortType | 1.3.6.1.4.1.8886.6.1.1.4.2.1.3 | INTEGER | read-only | port type identfies capability of Ether like interface. |
| ENA rcConsoleEnable | 1.3.6.1.4.1.8886.6.1.1.3.34 | EnableVar | read-write | Enable or disable console connect. |
| ENA rcDlfForwardingEnable | 1.3.6.1.4.1.8886.6.1.1.3.26 | EnableVar | read-write | whether forwarding DLF packets . |
| POR rcDot1xTransPorts | 1.3.6.1.4.1.8886.6.1.1.3.18 | PortList | read-write | The ports translating Dot1x packets. |
| T/F rcFastRoute | 1.3.6.1.4.1.8886.6.1.1.3.25 | TruthValue | read-write | true for fast route and false for normal route . |
| ENA rcGarpEnable | 1.3.6.1.4.1.8886.6.1.1.3.11 | EnableVar | read-write | GARP enable or disable |
| POR rcGarpTransPorts | 1.3.6.1.4.1.8886.6.1.1.3.20 | PortList | read-write | The ports translating Garp packets. |
| POR rcGmrpTransPorts | 1.3.6.1.4.1.8886.6.1.1.3.21 | PortList | read-write | The ports translating Gmrp packets. |
| POR rcGvrpTransPorts | 1.3.6.1.4.1.8886.6.1.1.3.22 | PortList | read-write | The ports translating Gvrp packets. |
| INT rcIpRouting | 1.3.6.1.4.1.8886.6.1.1.3.23 | INTEGER | read-write | start or stop system routing function . this is a commnd MIB variable . |
| ENA rcLacpEnable | 1.3.6.1.4.1.8886.6.1.1.3.12 | EnableVar | read-write | share vlan mode enable or disable |
| POR rcLacpTransPorts | 1.3.6.1.4.1.8886.6.1.1.3.19 | PortList | read-write | The ports translating Lacp packets. |
| MAC rcLoopbackDetectDestAddr | 1.3.6.1.4.1.8886.6.1.1.3.28 | MacAddress | read-write | destination MAC address of loopback-detection packet. |
| INT rcLoopbackDetectInterval | 1.3.6.1.4.1.8886.6.1.1.3.15 | INTEGER | read-write | Interval of sending loopback-detect packet. |
| I32 rcLoopbackDetectVlan | 1.3.6.1.4.1.8886.6.1.1.3.27 | Integer32 | read-write | loopback-detection packet belongs to which VLAN. |
| NTF rcLoopbackLinkDownTrap | 1.3.6.1.4.1.8886.6.1.1.5.2 | A linkDown trap signifies that the port identified by rcPortIndex change to link down state from link up. | ||
| NTF rcLoopbackLinkUpTrap | 1.3.6.1.4.1.8886.6.1.1.5.1 | A linkDown trap signifies that the port identified by rcPortIndex change to link up state from link down. | ||
| rcLoopbackTrap | 1.3.6.1.4.1.8886.6.1.1.5 | |||
| I32 rcMacAgingTime | 1.3.6.1.4.1.8886.6.1.1.3.1 | Integer32 | read-write | The value based 10 is the aging time for MAC address. Aging will be disable when aging time was (0) |
| INT rcMaxAllowedFrameLength | 1.3.6.1.4.1.8886.6.1.1.3.29 | INTEGER | read-write | the maximum packet size for the switch. |
| INT rcOperMaxAllowedFrameLength | 1.3.6.1.4.1.8886.6.1.1.3.37 | INTEGER | read-only | The actual maximum packet size for the switch. |
| rcPorConnectorChangeTrap | 1.3.6.1.4.1.8886.6.1.1.6 | |||
| INT rcPortAdminStatus | 1.3.6.1.4.1.8886.6.1.1.4.1.1.5 | INTEGER | read-write | The desired state of the interface. |
| NTF rcPortConnectorInsertTrap | 1.3.6.1.4.1.8886.6.1.1.6.1 | To notify NMS that connector has been inserted. If 'rcPortMediaAttachType' is 'combo' NMS need check 'rcComboPortTable' for deciding which combo port is inserted. | ||
| NTF rcPortConnectorRemoveTrap | 1.3.6.1.4.1.8886.6.1.1.6.2 | To notify NMS that connector has been removed. If 'rcPortMediaAttachType' is 'combo' NMS need check 'rcComboPortTable' for deciding which combo port is removed. | ||
| INT rcPortDefaultPriority | 1.3.6.1.4.1.8886.6.1.1.4.1.1.18 | INTEGER | read-write | The received untaged frames are forwarded to a proper queue according to this default priority. |
| C32 rcportDiscPKts | 1.3.6.1.4.1.8886.6.1.1.4.1.1.31 | Counter32 | read-only | The number of packets which were the difference between the total number of packets received on the interface and all packets transmitted out of the interface |
| INT rcPortDuplexSpeedGet | 1.3.6.1.4.1.8886.6.1.1.4.1.1.8 | INTEGER | read-only | The actual speed and duplex for this interface. If the interface is not configured for an acceptable value, a value of illegal(99) is returned. A value of unknown(1) is returned when the 'rcPortLink' indicates down(2) for this interface. |
| INT rcPortDuplexSpeedSet | 1.3.6.1.4.1.8886.6.1.1.4.1.1.7 | INTEGER | read-write | The desired speed and duplex for this interface. If the selected control is not possible on the interface, a value of illegal(99) is returned. If the port type does NOT support the default of autonegotiate(1), then the application initializes the port to a valid value (e.g., 1000full(6)). Note that not all controls are possible for all interfaces. For example, only full-1000(6) is available for Gigabit Ethernet interfaces. |
| rcPortEntry | 1.3.6.1.4.1.8886.6.1.1.4.1.1 | not-accessible | Table entry for switch port control and status information. | |
| ENA rcPortFlowControlEnable | 1.3.6.1.4.1.8886.6.1.1.4.1.1.9 | EnableVar | read-write | Set the flow control on the interface to enable(1) or disable(2). |
| ENA rcPortFlowControlRecvEnable | 1.3.6.1.4.1.8886.6.1.1.4.1.1.22 | EnableVar | read-write | Set the flow control on receive direction of the interface to enable(1) or disable(2). |
| ENA rcPortFlowControlRecvStatus | 1.3.6.1.4.1.8886.6.1.1.4.1.1.24 | EnableVar | read-only | The flow control status on receive direction of the interface to enable(1) or disable(2). |
| ENA rcPortFlowControlSendEnable | 1.3.6.1.4.1.8886.6.1.1.4.1.1.23 | EnableVar | read-write | Set the flow control on sender direction of the interface to enable(1) or disable(2). |
| ENA rcPortFlowControlSendStatus | 1.3.6.1.4.1.8886.6.1.1.4.1.1.25 | EnableVar | read-only | The flow control status on sender direction of the interface to enable(1) or disable(2). |
| I32 rcPortIndex | 1.3.6.1.4.1.8886.6.1.1.4.1.1.1 | Integer32 | read-only | An index based 1 that uniquely identifies a system interface. |
| rcPortInfoConfig | 1.3.6.1.4.1.8886.6.1.1.4 | |||
| INT rcPortLinkUpDelayTime | 1.3.6.1.4.1.8886.6.1.1.4.1.1.34 | INTEGER | read-write | The port link delay time. |
| INT rcPortLoopbackDetectDownTime | 1.3.6.1.4.1.8886.6.1.1.4.1.1.26 | INTEGER | read-write | time of loopback port shutdown. |
| ENA rcPortLoopbackDetectEnable | 1.3.6.1.4.1.8886.6.1.1.4.1.1.19 | EnableVar | read-write | Loopback detect of this port is on or off. |
| INT rcPortLoopbackDetectSrcPort | 1.3.6.1.4.1.8886.6.1.1.4.1.1.20 | INTEGER | read-only | The source port(it sends loopback-detect packets) makes of loop with loopback port. |
| ENA rcPortMacLearningEnable | 1.3.6.1.4.1.8886.6.1.1.4.1.1.10 | EnableVar | read-write | Set the learning ability on the interface to enable(1) or disable(2). |
| INT rcPortMacThreshold | 1.3.6.1.4.1.8886.6.1.1.4.1.1.11 | INTEGER | read-write | The Mac limit number on the interface or interface-vlan. |
| INT rcPortMacThresholdVlan | 1.3.6.1.4.1.8886.6.1.1.4.1.1.32 | INTEGER | read-write | when the Mac limits mac-thredshold on the interface-vlan, it indicates the VlanId;when the mac limits mac-thredshold on interface, its value is 4095. |
| rcPortMappingInfoConfig | 1.3.6.1.4.1.8886.6.1.1.8 | |||
| INT rcPortMDIXMode | 1.3.6.1.4.1.8886.6.1.1.4.1.1.29 | INTEGER | read-write | Automatic MDI Crossover mode of a port/PHY |
| INT rcPortMDIXStatus | 1.3.6.1.4.1.8886.6.1.1.4.1.1.30 | INTEGER | read-write | Automatic MDI Crossover mode of a port/PHY |
| INT rcPortMediaAttachCapability | 1.3.6.1.4.1.8886.6.1.1.4.1.1.28 | INTEGER | read-only | Medium type and capability of media attachment units. It is different with rcPortType which identifys the capability of the Ether like interface. |
| INT rcPortMediaAttachType | 1.3.6.1.4.1.8886.6.1.1.4.1.1.27 | INTEGER | read-only | media attachment type of this Ether like interface. |
| INT rcPortOperStatus | 1.3.6.1.4.1.8886.6.1.1.4.1.1.6 | INTEGER | read-only | The current operational state of the interface. |
| INT rcPortPhysicalStatus | 1.3.6.1.4.1.8886.6.1.1.4.1.1.33 | INTEGER | read-write | The current physical state of the interface. |
| ENA rcPortProtected | 1.3.6.1.4.1.8886.6.1.1.4.1.1.21 | EnableVar | read-write | Traffic between protected port group members are blocked. |
| ENA rcPortStormControlBcastEnable | 1.3.6.1.4.1.8886.6.1.1.4.1.1.12 | EnableVar | read-write | Set the broadcast storm control on the interface to enable(1) or disable(2). |
| INT rcPortStormControlBurst | 1.3.6.1.4.1.8886.6.1.1.4.1.1.15 | INTEGER | read-write | Set burst length when storm control open on the interface. . |
| ENA rcPortStormControlDlfEnable | 1.3.6.1.4.1.8886.6.1.1.4.1.1.14 | EnableVar | read-write | Set the DLF storm control on the interface to enable(1) or disable(2). |
| rcPortStormControlEntry | 1.3.6.1.4.1.8886.6.1.1.4.3.1 | not-accessible | Table entry for ports' storm control information. | |
| INT rcPortStormControlLimit | 1.3.6.1.4.1.8886.6.1.1.4.1.1.16 | INTEGER | read-write | The limit number for storm control on this port . |
| INT rcPortStormControlLimitRatio | 1.3.6.1.4.1.8886.6.1.1.4.1.1.17 | INTEGER | read-write | storm control limit ratio on this port |
| INT rcPortStormControlMaxValue | 1.3.6.1.4.1.8886.6.1.1.4.3.1.4 | INTEGER | read-write | Max value for storm control. |
| ENA rcPortStormControlMcastEnable | 1.3.6.1.4.1.8886.6.1.1.4.1.1.13 | EnableVar | read-write | Set the multicast storm control on the interface to enable(1) or disable(2). |
| INT rcPortStormControlPktType | 1.3.6.1.4.1.8886.6.1.1.4.3.1.2 | INTEGER | not-accessible | An index that uniquely identifies packet type for storm control. |
| INT rcPortStormControlPortIndex | 1.3.6.1.4.1.8886.6.1.1.4.3.1.1 | INTEGER | not-accessible | An index based 1 that uniquely identifies a Ether like interface. |
| rcPortStormControlTable | 1.3.6.1.4.1.8886.6.1.1.4.3 | not-accessible | A table of ports' storm control properties. | |
| INT rcPortStormControlUnit | 1.3.6.1.4.1.8886.6.1.1.4.3.1.3 | INTEGER | read-write | unit of value for storm control. |
| rcPortTable | 1.3.6.1.4.1.8886.6.1.1.4.1 | not-accessible | A table of switch port and associated properties. | |
| INT rcPortType | 1.3.6.1.4.1.8886.6.1.1.4.1.1.2 | INTEGER | read-only | port type,same as slot type. |
| INT rcPvidSpaceNum | 1.3.6.1.4.1.8886.6.1.1.3.14 | INTEGER | read-write | The system supports at most rcPvidSpaceSize vlans, so the vlan ID increases at rcPvidSpaceSize step over. |
| INT rcSlotIndex | 1.3.6.1.4.1.8886.6.1.1.2.2.1.1 | INTEGER | not-accessible | slot index based 0 |
| rcSlotInformation | 1.3.6.1.4.1.8886.6.1.1.2 | |||
| INT rcSlotNum | 1.3.6.1.4.1.8886.6.1.1.2.1 | INTEGER | read-only | Total number of slot |
| INT rcSlotPortIndex | 1.3.6.1.4.1.8886.6.1.1.4.1.1.4 | INTEGER | read-only | index of this port in the slot |
| INT rcSlotPortNum | 1.3.6.1.4.1.8886.6.1.1.2.2.1.3 | INTEGER | read-only | the number of ports in this slot |
| INT rcSlotPortStart | 1.3.6.1.4.1.8886.6.1.1.2.2.1.2 | INTEGER | read-only | the start number of port in this slot |
| rcSlotStateEntry | 1.3.6.1.4.1.8886.6.1.1.2.2.1 | not-accessible | A list of slot. | |
| rcSlotStateTable | 1.3.6.1.4.1.8886.6.1.1.2.2 | not-accessible | A table of slot . | |
| INT rcSlotTableIndex | 1.3.6.1.4.1.8886.6.1.1.4.1.1.3 | INTEGER | read-only | the index of slot which this port is in. |
| INT rcSlotType | 1.3.6.1.4.1.8886.6.1.1.2.2.1.4 | INTEGER | read-only | slot type |
| I32 rcStaticRouteDistance | 1.3.6.1.4.1.8886.6.1.1.3.24 | Integer32 | read-write | system static route distance value . this is a commnd MIB variable . |
| ENA rcStormControlBcastEnable | 1.3.6.1.4.1.8886.6.1.1.3.2 | EnableVar | read-write | Set the Storm control for broadcast on the interface to enable(1) or disable(2). |
| INT rcStormControlbps | 1.3.6.1.4.1.8886.6.1.1.3.6 | INTEGER | read-write | The limit number for storm control on the interface . |
| INT rcStormControlBurst | 1.3.6.1.4.1.8886.6.1.1.3.8 | INTEGER | read-write | Set burst length when storm control open on the interface. . |
| ENA rcStormControlDlfEnable | 1.3.6.1.4.1.8886.6.1.1.3.4 | EnableVar | read-write | Set the Storm control for DLF on the interface to enable(1) or disable(2). |
| ENA rcStormControlMcastEnable | 1.3.6.1.4.1.8886.6.1.1.3.3 | EnableVar | read-write | Set the Storm control for multicast on the interface to enable(1) or disable(2). |
| INT rcStormControlOperbps | 1.3.6.1.4.1.8886.6.1.1.3.36 | INTEGER | read-only | The actual limit number for storm control on the interface . |
| INT rcStormControlOperpps | 1.3.6.1.4.1.8886.6.1.1.3.35 | INTEGER | read-only | The actual limit number for storm control on the interface . |
| INT rcStormControlpps | 1.3.6.1.4.1.8886.6.1.1.3.5 | INTEGER | read-write | The limit number for storm control on the interface . |
| INT rcStormControlRatio | 1.3.6.1.4.1.8886.6.1.1.3.7 | INTEGER | read-write | storm control limit ratio |
| ENA rcStpEnable | 1.3.6.1.4.1.8886.6.1.1.3.9 | EnableVar | read-write | The enabled/disabled status of STP for the bridge entity. |
| I32 rcSvlDefaultVlan | 1.3.6.1.4.1.8886.6.1.1.3.30 | Integer32 | read-write | default vlan which the mac address is also learned to. |
| ENA rcSvlEnable | 1.3.6.1.4.1.8886.6.1.1.3.10 | EnableVar | read-write | share vlan mode enable or disable |
| OCT rcSwitchBackBoardName | 1.3.6.1.4.1.8886.6.1.1.1.22 | OCTET STRING | read-only | Backboard name. |
| OCT rcSwitchBackBoardSerialNumber | 1.3.6.1.4.1.8886.6.1.1.1.21 | OCTET STRING | read-only | Serial number of the backboard. |
| OCT rcSwitchBackBoardVendorName | 1.3.6.1.4.1.8886.6.1.1.1.20 | OCTET STRING | read-only | Backboard vendor name. |
| OCT rcSwitchBackBoardVersion | 1.3.6.1.4.1.8886.6.1.1.1.23 | OCTET STRING | read-only | Backboard version. |
| OCT rcSwitchBootstrapVersion | 1.3.6.1.4.1.8886.6.1.1.1.13 | OCTET STRING | read-only | rose bootstrap version . |
| OCT rcSwitchCmpAbName | 1.3.6.1.4.1.8886.6.1.1.1.17 | OCTET STRING | read-only | manufacturer abbreviated name |
| OCT rcSwitchCmpFullName | 1.3.6.1.4.1.8886.6.1.1.1.18 | OCTET STRING | read-only | manufacturer full name |
| rcSwitchConfig | 1.3.6.1.4.1.8886.6.1.1.3 | |||
| INT rcSwitchDefaultVlan | 1.3.6.1.4.1.8886.6.1.1.1.12 | INTEGER | read-only | Default vlan |
| OCT rcSwitchDeviceName | 1.3.6.1.4.1.8886.6.1.1.1.19 | OCTET STRING | read-only | device name |
| OCT rcSwitchFpgaVersion | 1.3.6.1.4.1.8886.6.1.1.1.15 | OCTET STRING | read-only | rose fpga version. |
| OCT rcSwitchHardwareVersion | 1.3.6.1.4.1.8886.6.1.1.1.2 | OCTET STRING | read-only | rose hardware version . |
| rcSwitchInformation | 1.3.6.1.4.1.8886.6.1.1.1 | |||
| I32 rcSwitchLastErrorCode | 1.3.6.1.4.1.8886.6.1.1.1.4 | Integer32 | read-only | This mib object stand for system last error code ,for system analysis 0 for no error 1 ...0x7fffffff for error code |
| MAC rcSwitchMacAddress | 1.3.6.1.4.1.8886.6.1.1.1.9 | MacAddress | read-only | MAC address. |
| I32 rcSwitchMacTableCapability | 1.3.6.1.4.1.8886.6.1.1.1.8 | Integer32 | read-only | The capability of MAC table. |
| INT rcSwitchMaxAggregationPortNum | 1.3.6.1.4.1.8886.6.1.1.1.6 | INTEGER | read-only | The aggregation port number which system supports. |
| INT rcSwitchMaxL3IpSubnetNum | 1.3.6.1.4.1.8886.6.1.1.1.7 | INTEGER | read-only | The layer 3 port number which system supports. |
| INT rcSwitchMaxPhysicalPortNum | 1.3.6.1.4.1.8886.6.1.1.1.5 | INTEGER | read-only | The physical port number which system supports. |
| OCT rcSwitchProductVersion | 1.3.6.1.4.1.8886.6.1.1.1.16 | OCTET STRING | read-only | product version |
| INT rcSwitchPvidSpaceSize | 1.3.6.1.4.1.8886.6.1.1.1.11 | INTEGER | read-only | |
| OCT rcSwitchRoseVersion | 1.3.6.1.4.1.8886.6.1.1.1.1 | OCTET STRING | read-only | rose software version . |
| OCT rcSwitchSerialNumber | 1.3.6.1.4.1.8886.6.1.1.1.14 | OCTET STRING | read-only | The serial number of the motherboard. |
| I32 rcSwitchServiceInfo | 1.3.6.1.4.1.8886.6.1.1.1.3 | Integer32 | read-only | rose software service information version . every bit stand for one type of service and , '0' stand for service is up, '1' stand for not start Qos-- bit(0) Filter -- bit(1) Storm control -- bit(2) Authentication-- bit(3) IGMP Snooping-- bit(4) STP-- bit(5) RIP-- bit(6) OSPF-- bit(7) PIM-DM-- bit(8) PIM-SM-- bit(9) .... |
| INT rcSwitchVlanSpaceSize | 1.3.6.1.4.1.8886.6.1.1.1.10 | INTEGER | read-only | the number of vlans in a vlan |
| rcSystem | 1.3.6.1.4.1.8886.6.1.1 | iscom switch system Enterprise MIB definition. | ||
| POR rcTelnetAcceptPorts | 1.3.6.1.4.1.8886.6.1.1.3.32 | PortList | read-write | Ports that access telnet connect request to telnet server on device. |
| I32 rcTelnetMaxSessions | 1.3.6.1.4.1.8886.6.1.1.3.31 | Integer32 | read-write | Max sessions device telnet server permits. '0' indicates that device won't permits any telnet connect. |
| ENA rcTrapBindipEnable | 1.3.6.1.4.1.8886.6.1.1.3.38 | EnableVar | read-write | Enable or disable rapBindip.DEFVAL { disable } |
| INT rcUspIfIndex | 1.3.6.1.4.1.8886.6.1.1.8.7.1.5 | INTEGER | read-only | The If Index which is mapped to the IF. |
| INT rcUspIfState | 1.3.6.1.4.1.8886.6.1.1.8.6.1.5 | INTEGER | read-only | The IF State. |
| rcUspIfToUspMappingEntry | 1.3.6.1.4.1.8886.6.1.1.8.6.1 | not-accessible | Defines an entry in the rcUspIfToUspMappingTable.The index is ifIndex,while is unique in raisecom private mib. | |
| INT rcUspIfToUspMappingPortIndex | 1.3.6.1.4.1.8886.6.1.1.8.6.1.3 | INTEGER | read-only | The port index which IF is mapped to. |
| INT rcUspIfToUspMappingSlotIndex | 1.3.6.1.4.1.8886.6.1.1.8.6.1.2 | INTEGER | read-only | The slot index which IF is mapped to. |
| rcUspIfToUspMappingTable | 1.3.6.1.4.1.8886.6.1.1.8.6 | not-accessible | The table describes how the IF map to the USP. | |
| INT rcUspIfToUspMappingUnitIndex | 1.3.6.1.4.1.8886.6.1.1.8.6.1.1 | INTEGER | read-only | The unit index which IF is mapped to. |
| INT rcUspIfType | 1.3.6.1.4.1.8886.6.1.1.8.6.1.4 | INTEGER | read-only | The IF type which IF is mapped to. |
| INT rcUspIfTypeIndex | 1.3.6.1.4.1.8886.6.1.1.8.7.1.4 | INTEGER | not-accessible | The port type which is mapped to the IF. |
| INT rcUspPortIndex | 1.3.6.1.4.1.8886.6.1.1.8.2.1.4 | INTEGER | read-only | The port index which the USP is mapped to. |
| rcUspPortToUspMappingEntry | 1.3.6.1.4.1.8886.6.1.1.8.1.1 | not-accessible | Defines an entry in the rcUspPortToUspMappingTable.The index is rcPortIndex,while is unique in raisecom private mib. | |
| INT rcUspPortToUspMappingPortIndex | 1.3.6.1.4.1.8886.6.1.1.8.1.1.3 | INTEGER | read-only | The port index which port is mapped to. |
| INT rcUspPortToUspMappingSlotIndex | 1.3.6.1.4.1.8886.6.1.1.8.1.1.2 | INTEGER | read-only | The slot index which port is mapped to. |
| rcUspPortToUspMappingTable | 1.3.6.1.4.1.8886.6.1.1.8.1 | not-accessible | The table describes how the port map to the USP. | |
| INT rcUspPortToUspMappingUnitIndex | 1.3.6.1.4.1.8886.6.1.1.8.1.1.1 | INTEGER | read-only | The unit index which port is mapped to. |
| INT rcUspSlotActualSubcardType | 1.3.6.1.4.1.8886.6.1.1.8.5.1.5 | INTEGER | read-only | The type of subcard which is inserted to the slot. |
| rcUspSlotEntry | 1.3.6.1.4.1.8886.6.1.1.8.5.1 | not-accessible | Defines an entry in the rcUspSlotTable.The indexes are rcUspSlotUnitIndex and rcUspSlotSlotIndex. | |
| OCT rcUspSlotHardVersion | 1.3.6.1.4.1.8886.6.1.1.8.5.1.7 | OCTET STRING | read-only | The hard version of slot. |
| INT rcUspSlotPortNum | 1.3.6.1.4.1.8886.6.1.1.8.5.1.10 | INTEGER | read-only | The number of ports this slot has. |
| INT rcUspSlotPortStart | 1.3.6.1.4.1.8886.6.1.1.8.5.1.9 | INTEGER | read-only | The global port index this slot starts from. |
| INT rcUspSlotRightSubcardType | 1.3.6.1.4.1.8886.6.1.1.8.5.1.4 | INTEGER | read-only | The type of subcard which is suitable to the slot. |
| OCT rcUspSlotSerial | 1.3.6.1.4.1.8886.6.1.1.8.5.1.6 | OCTET STRING | read-only | The serial number of slot. |
| INT rcUspSlotSlotIndex | 1.3.6.1.4.1.8886.6.1.1.8.5.1.2 | INTEGER | not-accessible | The slot index. |
| INT rcUspSlotSlotState | 1.3.6.1.4.1.8886.6.1.1.8.5.1.11 | INTEGER | read-only | The slot State. |
| INT rcUspSlotSlotType | 1.3.6.1.4.1.8886.6.1.1.8.5.1.3 | INTEGER | read-only | The slot type. |
| OCT rcUspSlotSoftwareVersion | 1.3.6.1.4.1.8886.6.1.1.8.5.1.8 | OCTET STRING | read-only | The soft version of slot. |
| rcUspSlotTable | 1.3.6.1.4.1.8886.6.1.1.8.5 | not-accessible | The table describes the detail of slot. | |
| INT rcUspSlotUnitIndex | 1.3.6.1.4.1.8886.6.1.1.8.5.1.1 | INTEGER | not-accessible | The unit index which a slot belongs to. |
| rcUspUnitEntry | 1.3.6.1.4.1.8886.6.1.1.8.4.1 | not-accessible | Defines an entry in the rcUspUnitTable.The index is rcUspUnitIndex. | |
| INT rcUspUnitIndex | 1.3.6.1.4.1.8886.6.1.1.8.4.1.1 | INTEGER | not-accessible | The port index which the USP is mapped to. |
| INT rcUspUnitNum | 1.3.6.1.4.1.8886.6.1.1.8.3 | INTEGER | read-only | The total unit number. |
| INT rcUspUnitPortNum | 1.3.6.1.4.1.8886.6.1.1.8.4.1.3 | INTEGER | read-only | The total port num which the corresponding unit has. |
| INT rcUspUnitSlotNum | 1.3.6.1.4.1.8886.6.1.1.8.4.1.2 | INTEGER | read-only | The total slot num which the corresponding unit has. |
| rcUspUnitTable | 1.3.6.1.4.1.8886.6.1.1.8.4 | not-accessible | The table describes the detail of unit. | |
| rcUspUspToIfMappingEntry | 1.3.6.1.4.1.8886.6.1.1.8.7.1 | not-accessible | Defines an entry in the rcUspUspToIfMappingTable.The indexes are rcUspUspToIfMappingUnitIndex,rcUspUspToIfMappingSlotIndex,rcUspUspToIfMappingPortIndex and rcUspIfTypeIndex. | |
| INT rcUspUspToIfMappingPortIndex | 1.3.6.1.4.1.8886.6.1.1.8.7.1.3 | INTEGER | not-accessible | The port index which is mapped to the IF. |
| INT rcUspUspToIfMappingSlotIndex | 1.3.6.1.4.1.8886.6.1.1.8.7.1.2 | INTEGER | not-accessible | The slot index which is mapped to the IF. |
| rcUspUspToIfMappingTable | 1.3.6.1.4.1.8886.6.1.1.8.7 | not-accessible | The table describes how the USP map to the IF. | |
| INT rcUspUspToIfMappingUnitIndex | 1.3.6.1.4.1.8886.6.1.1.8.7.1.1 | INTEGER | not-accessible | The unit index which is mapped to the IF. |
| rcUspUspToPortMappingEntry | 1.3.6.1.4.1.8886.6.1.1.8.2.1 | not-accessible | Defines an entry in the rcUspUspToPortMappingTable.The indexes are rcUspUspToPortMappingUnitIndex,rcUspUspToPortMappingSlotIndex and rcUspUspToPortMappingPortIndex. | |
| INT rcUspUspToPortMappingPortIndex | 1.3.6.1.4.1.8886.6.1.1.8.2.1.3 | INTEGER | not-accessible | The port index which is mapped to the port. |
| INT rcUspUspToPortMappingSlotIndex | 1.3.6.1.4.1.8886.6.1.1.8.2.1.2 | INTEGER | not-accessible | The slot index which is mapped to the port. |
| rcUspUspToPortMappingTable | 1.3.6.1.4.1.8886.6.1.1.8.2 | not-accessible | The table describes how the USP map to the port. | |
| INT rcUspUspToPortMappingUnitIndex | 1.3.6.1.4.1.8886.6.1.1.8.2.1.1 | INTEGER | not-accessible | The unit index which is mapped to the port. |
| VLA rcVlanMacLearning | 1.3.6.1.4.1.8886.6.1.1.3.33 | Vlanset | read-write | Enable or disable source MAC address learning on VLAN. |
| INT rcVlanSpaceNum | 1.3.6.1.4.1.8886.6.1.1.3.13 | INTEGER | read-write | The system supports at most rcVlanSpaceSize vlans, so the vlan ID increases at rcVlanSpaceSize step over. |
RFC description
Raisecom proprietary MIB for network switch system management and configuration.
Start monitoring Raisecom iSCOM-series metro Ethernet switch family (system identity/hardware inventory) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.