All MIBs › STN-PPTP-MIB
Organization: Spring Tide Networks, Inc.
Last Updated: 2000-02-16
Category: IPsec / VPN, Spring Tide Networks
Description: Manages Spring Tide Networks PPTP tunnel configuration, control connection state, and data channel parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is STN-PPTP-MIB?
STN-PPTP-MIB is a Spring Tide Networks enterprise MIB for managing the Point-to-Point Tunneling Protocol on Spring Tide subscriber/service platforms. It defines objects describing PPTP tunnel configuration, control-connection state, and data-channel parameters used to establish and maintain VPN tunnels. Its monitoring focus is largely software/protocol-state: control connection status and per-channel parameters that reveal whether a PPTP tunnel is correctly established or has failed to negotiate, which is critical for remote-access VPN troubleshooting. It implements a vendor MIB analogous in scope to the standard PPTP state machine described in RFC 2637, though as an enterprise MIB it is not a direct extension of any IETF MIB. It is deployed on legacy Spring Tide Networks access/tunneling platforms providing PPTP-based remote-access VPN service, with the STN-PPTP-MIB MIB remaining the reference for interpreting tunnel state on those legacy platforms.
IPNetwork Monitor allows you to monitor SNMP objects defined in STN-PPTP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Spring Tide Networks tunneling/access platforms
Monitoring Examples
This MIB's sample object list is empty in the source data, so specific OID names cannot be cited here. Based on the module description, a typical use would be polling PPTP control-connection state and data-channel status per tunnel to detect a tunnel stuck in a non-established state. Such a state would indicate a failed negotiation between the remote client and the tunneling gateway.
What Can Be Monitored
- PPTP control connection state
- PPTP data channel parameters
- tunnel establishment status
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
| stnTmpProtocols | OBJECT-IDENTITY |
| StnDomainMapType |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| stnPptp | 1.3.6.1.4.1.3551.4.1.10 | The MIB module that describes managed objects of general use by the Point-to-Point Transport Protocol. | ||
| stnPptpObjects | 1.3.6.1.4.1.3551.4.1.10.1 | |||
| stnPptpScalar | 1.3.6.1.4.1.3551.4.1.10.1.1 | |||
| stnPptpConfig | 1.3.6.1.4.1.3551.4.1.10.1.1.1 | |||
| INT stnPptpAdminState | 1.3.6.1.4.1.3551.4.1.10.1.1.1.1 | INTEGER | read-write | This object defines the administrative state of this PPTP tunnel domain. Setting this object to 'disabled' causes all tunnels to be immediately disconnected and no further tunnels to be either initiated or accepted. |
| stnPptpStats | 1.3.6.1.4.1.3551.4.1.10.1.1.2 | |||
| OCT stnPptpProtocolVersion | 1.3.6.1.4.1.3551.4.1.10.1.1.2.1 | OCTET STRING | read-only | Vector of supported PPTP protocol version and revision numbers. Supported versions are identified via a two octet pairing where the first octet indicates the version and the second octet contains the revision. |
| STR stnPptpVendorName | 1.3.6.1.4.1.3551.4.1.10.1.1.2.2 | DisplayString | read-only | This object identifies the Vendor name of the PPTP protocol stack. |
| I32 stnPptpFirmwareRev | 1.3.6.1.4.1.3551.4.1.10.1.1.2.3 | Integer32 | read-only | This object defines the firmware revision for the PPTP protocol stack. |
| stnPptpDomainConfigTable | 1.3.6.1.4.1.3551.4.1.10.1.2 | not-accessible | The PPTP Domain configuration table. | |
| stnPptpDomainConfigEntry | 1.3.6.1.4.1.3551.4.1.10.1.2.1 | not-accessible | An PPTP Domain configuration entry. An entry in this table may correspond to a single endpoint or a group of tunnel endpoints. | |
| STR stnPptpDomainConfigIdentifier | 1.3.6.1.4.1.3551.4.1.10.1.2.1.1 | DisplayString | not-accessible | This object is not used. |
| INT stnPptpDomainConfigAdminState | 1.3.6.1.4.1.3551.4.1.10.1.2.1.2 | INTEGER | read-create | This object is not used. |
| INT stnPptpDomainConfigAuthentication | 1.3.6.1.4.1.3551.4.1.10.1.2.1.3 | INTEGER | read-create | This object is not used |
| OCT stnPptpDomainConfigSecret | 1.3.6.1.4.1.3551.4.1.10.1.2.1.4 | OCTET STRING | read-create | This object is not used |
| INT stnPptpDomainConfigTunnelSecurity | 1.3.6.1.4.1.3551.4.1.10.1.2.1.5 | INTEGER | read-create | This object is not used. |
| I32 stnPptpDomainConfigTunnelHelloInterval | 1.3.6.1.4.1.3551.4.1.10.1.2.1.6 | Integer32 | read-create | This object is not used. |
| I32 stnPptpDomainConfigTunnelIdleTimeout | 1.3.6.1.4.1.3551.4.1.10.1.2.1.7 | Integer32 | read-create | This object is not used. |
| I32 stnPptpDomainConfigControlRWS | 1.3.6.1.4.1.3551.4.1.10.1.2.1.8 | Integer32 | read-create | This object is not used. |
| I32 stnPptpDomainConfigControlRetransmissions | 1.3.6.1.4.1.3551.4.1.10.1.2.1.9 | Integer32 | read-create | This object is not used. |
| T/F stnPptpDomainConfigPayloadSequencing | 1.3.6.1.4.1.3551.4.1.10.1.2.1.10 | TruthValue | read-create | This object is not used. |
| I32 stnPptpDomainConfigPayloadRWS | 1.3.6.1.4.1.3551.4.1.10.1.2.1.11 | Integer32 | read-create | This object is not used. |
| MIL stnPptpDomainConfigDelayedAckTimeout | 1.3.6.1.4.1.3551.4.1.10.1.2.1.12 | MilliSeconds | read-create | This object is not used. |
| MIL stnPptpDomainConfigReassemblyTimeout | 1.3.6.1.4.1.3551.4.1.10.1.2.1.13 | MilliSeconds | read-create | This object is not used. |
| ROW stnPptpDomainConfigStatus | 1.3.6.1.4.1.3551.4.1.10.1.2.1.14 | RowStatus | read-create | This object is not used. |
| stnPptpDomainStatsTable | 1.3.6.1.4.1.3551.4.1.10.1.3 | not-accessible | The PPTP Domain Status and Statistics table. | |
| stnPptpDomainStatsEntry | 1.3.6.1.4.1.3551.4.1.10.1.3.1 | not-accessible | An PPTP Domain Stats entry. An entry in this table may correspond to a single endpoint or a group of tunnel endpoints. | |
| STR stnPptpDomainStatsIdentifier | 1.3.6.1.4.1.3551.4.1.10.1.3.1.1 | DisplayString | not-accessible | The identifier, usually in the form of a Domain Name (full or partial), describing a single tunnel endpoint or a domain of tunnel endpoints. |
| C32 stnPptpDomainStatsTotalTunnels | 1.3.6.1.4.1.3551.4.1.10.1.3.1.2 | Counter32 | read-only | This object returns the total number of tunnels that have successfully reached the established state for this tunnel domain. |
| C32 stnPptpDomainStatsFailedTunnels | 1.3.6.1.4.1.3551.4.1.10.1.3.1.3 | Counter32 | read-only | This object returns the number of tunnels that failed to reach the established state for this tunnel domain. |
| C32 stnPptpDomainStatsFailedAuthentications | 1.3.6.1.4.1.3551.4.1.10.1.3.1.4 | Counter32 | read-only | This object is not used. |
| G32 stnPptpDomainStatsActiveTunnels | 1.3.6.1.4.1.3551.4.1.10.1.3.1.5 | Gauge32 | read-only | This object returns the number of tunnels that are currently active for this domain. |
| C32 stnPptpDomainStatsTotalSessions | 1.3.6.1.4.1.3551.4.1.10.1.3.1.6 | Counter32 | read-only | This object returns the total number of sessions that have successfully reached the established state for this tunnel domain. |
| C32 stnPptpDomainStatsFailedSessions | 1.3.6.1.4.1.3551.4.1.10.1.3.1.7 | Counter32 | read-only | This object returns the number of sessions that failed to reach the established state for this tunnel domain. |
| G32 stnPptpDomainStatsActiveSessions | 1.3.6.1.4.1.3551.4.1.10.1.3.1.8 | Gauge32 | read-only | This object returns the number of sessions that are currently active for this domain. |
| C32 stnPptpDomainStatsControlRecvOctets | 1.3.6.1.4.1.3551.4.1.10.1.3.1.9 | Counter32 | read-only | This object returns the number of control channel octets received for this tunnel domain. |
| C32 stnPptpDomainStatsControlRecvPackets | 1.3.6.1.4.1.3551.4.1.10.1.3.1.10 | Counter32 | read-only | This object returns the number of control packets received for this tunnel domain. |
| C32 stnPptpDomainStatsControlSendOctets | 1.3.6.1.4.1.3551.4.1.10.1.3.1.11 | Counter32 | read-only | This object returns the number of control channel octets that were transmitted to tunnel endpoints for this domain. |
| C32 stnPptpDomainStatsControlSendPackets | 1.3.6.1.4.1.3551.4.1.10.1.3.1.12 | Counter32 | read-only | This object returns the number of control packets that were transmitted to tunnel endpoints for this domain. |
| C32 stnPptpDomainStatsPayloadRecvOctets | 1.3.6.1.4.1.3551.4.1.10.1.3.1.13 | Counter32 | read-only | This object returns the number of payload channel octets that were received for this tunnel domain. |
| C32 stnPptpDomainStatsPayloadRecvPackets | 1.3.6.1.4.1.3551.4.1.10.1.3.1.14 | Counter32 | read-only | This object returns the number of payload packets that were received for this tunnel domain. |
| C32 stnPptpDomainStatsPayloadRecvDiscards | 1.3.6.1.4.1.3551.4.1.10.1.3.1.15 | Counter32 | read-only | This object returns the number of received payload packets that were discarded by this this tunnel domain. |
| C32 stnPptpDomainStatsPayloadSendOctets | 1.3.6.1.4.1.3551.4.1.10.1.3.1.16 | Counter32 | read-only | This object returns the number of payload channel octets that were transmitted to tunnel peers within this tunnel domain. |
| C32 stnPptpDomainStatsPayloadSendPackets | 1.3.6.1.4.1.3551.4.1.10.1.3.1.17 | Counter32 | read-only | This object returns the number of payload packets that were transmitted to tunnel peers within this tunnel domain. |
| stnPptpTunnelConfigTable | 1.3.6.1.4.1.3551.4.1.10.1.4 | not-accessible | The PPTP tunnel configuration table. | |
| stnPptpTunnelConfigEntry | 1.3.6.1.4.1.3551.4.1.10.1.4.1 | not-accessible | A PPTP tunnel interface configuration entry. | |
| NUM stnPptpTunnelConfigIfIndex | 1.3.6.1.4.1.3551.4.1.10.1.4.1.1 | InterfaceIndex | read-only | This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type PPTP. |
| INT stnPptpTunnelConfigAuthentication | 1.3.6.1.4.1.3551.4.1.10.1.4.1.2 | INTEGER | read-write | This object is not used. |
| OCT stnPptpTunnelConfigSecret | 1.3.6.1.4.1.3551.4.1.10.1.4.1.3 | OCTET STRING | read-write | This object is not used. |
| INT stnPptpTunnelConfigSecurity | 1.3.6.1.4.1.3551.4.1.10.1.4.1.4 | INTEGER | read-write | This object is not used. |
| I32 stnPptpTunnelConfigHelloInterval | 1.3.6.1.4.1.3551.4.1.10.1.4.1.5 | Integer32 | read-write | This object is not used. |
| I32 stnPptpTunnelConfigIdleTimeout | 1.3.6.1.4.1.3551.4.1.10.1.4.1.6 | Integer32 | read-write | This object is not used. |
| I32 stnPptpTunnelConfigControlRWS | 1.3.6.1.4.1.3551.4.1.10.1.4.1.7 | Integer32 | read-write | This object is not used. |
| I32 stnPptpTunnelConfigControlRetransmissions | 1.3.6.1.4.1.3551.4.1.10.1.4.1.8 | Integer32 | read-write | This object is not used. |
| T/F stnPptpTunnelConfigPayloadSequencing | 1.3.6.1.4.1.3551.4.1.10.1.4.1.9 | TruthValue | read-write | This object is not used. |
| I32 stnPptpTunnelConfigPayloadRWS | 1.3.6.1.4.1.3551.4.1.10.1.4.1.10 | Integer32 | read-write | This object is not used. |
| MIL stnPptpTunnelConfigDelayedAckTimeout | 1.3.6.1.4.1.3551.4.1.10.1.4.1.11 | MilliSeconds | read-write | This object is not used. |
| MIL stnPptpTunnelConfigReassemblyTimeout | 1.3.6.1.4.1.3551.4.1.10.1.4.1.12 | MilliSeconds | read-write | This object is not used. |
| INT stnPptpTunnelConfigTransport | 1.3.6.1.4.1.3551.4.1.10.1.4.1.13 | INTEGER | read-write | This object defines the underlying transport media that is in use for this tunnel entry. Different tunnel transports may define MIB extensions to the PPTP tunnel table to realize the transport layer. |
| stnPptpTunnelStatsTable | 1.3.6.1.4.1.3551.4.1.10.1.5 | not-accessible | The PPTP tunnel status and statistics table. | |
| stnPptpTunnelStatsEntry | 1.3.6.1.4.1.3551.4.1.10.1.5.1 | not-accessible | An PPTP tunnel interface stats entry. | |
| NUM stnPptpTunnelStatsIfIndex | 1.3.6.1.4.1.3551.4.1.10.1.5.1.1 | InterfaceIndex | read-only | This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type PPTP. |
| I32 stnPptpTunnelStatsLocalTID | 1.3.6.1.4.1.3551.4.1.10.1.5.1.2 | Integer32 | read-only | This object contains the local tunnel Identifier. |
| INT stnPptpTunnelStatsState | 1.3.6.1.4.1.3551.4.1.10.1.5.1.3 | INTEGER | read-only | This field contains the current state of the control tunnel. |
| INT stnPptpTunnelStatsInitiated | 1.3.6.1.4.1.3551.4.1.10.1.5.1.4 | INTEGER | read-only | This object indicates whether the tunnel was initiated locally or by the remote tunnel peer. |
| STR stnPptpTunnelStatsRemoteHostName | 1.3.6.1.4.1.3551.4.1.10.1.5.1.5 | DisplayString | read-only | This object contains the host name as discovered during the tunnel establishment phase |
| STR stnPptpTunnelStatsRemoteVendorName | 1.3.6.1.4.1.3551.4.1.10.1.5.1.6 | DisplayString | read-only | This object identifies the vendor name of the peer's PPTP implementation. |
| I32 stnPptpTunnelStatsRemoteFirmwareRevision | 1.3.6.1.4.1.3551.4.1.10.1.5.1.7 | Integer32 | read-only | This object contains the tunnel peer's firmware revision number. |
| OCT stnPptpTunnelStatsRemoteProtocolVersion | 1.3.6.1.4.1.3551.4.1.10.1.5.1.8 | OCTET STRING | read-only | This object describes the protocol version and revision of the tunnel peers implementation. The first octet contains the protocol version. The second octet contains the protocol revision. |
| INT stnPptpTunnelStatsBearerCapabilities | 1.3.6.1.4.1.3551.4.1.10.1.5.1.9 | INTEGER | read-only | This object describes the Bearer Capabilities of the tunnel peer. |
| INT stnPptpTunnelStatsFramingCapabilities | 1.3.6.1.4.1.3551.4.1.10.1.5.1.10 | INTEGER | read-only | This object describes the Framing Capabilities of the tunnel peer. |
| C32 stnPptpTunnelStatsControlRecvPackets | 1.3.6.1.4.1.3551.4.1.10.1.5.1.11 | Counter32 | read-only | This object contains the number of control packets received on the tunnel. |
| C32 stnPptpTunnelStatsControlSendPackets | 1.3.6.1.4.1.3551.4.1.10.1.5.1.12 | Counter32 | read-only | This object contains the number of control packets that were transmitted to the tunnel peer. |
| C32 stnPptpTunnelStatsTotalSessions | 1.3.6.1.4.1.3551.4.1.10.1.5.1.13 | Counter32 | read-only | This object contains the total number of sessions that this tunnel has successfully connected through to its tunnel peer since this tunnel was created. |
| C32 stnPptpTunnelStatsFailedSessions | 1.3.6.1.4.1.3551.4.1.10.1.5.1.14 | Counter32 | read-only | This object contains the total number of sessions that were initiated but failed to reach the established phase. |
| G32 stnPptpTunnelStatsActiveSessions | 1.3.6.1.4.1.3551.4.1.10.1.5.1.15 | Gauge32 | read-only | This object contains the total number of sessions in the established state for this tunnel. |
| I32 stnPptpTunnelStatsLastResultCode | 1.3.6.1.4.1.3551.4.1.10.1.5.1.16 | Integer32 | read-only | This object contains the last value of the result code as described in the Result Code which caused the tunnel to disconnect. |
| I32 stnPptpTunnelStatsLastErrorCode | 1.3.6.1.4.1.3551.4.1.10.1.5.1.17 | Integer32 | read-only | This object contains the last value of the error code as described in the Result Code which caused the tunnel to disconnect. |
| STR stnPptpTunnelStatsLastErrorMessage | 1.3.6.1.4.1.3551.4.1.10.1.5.1.18 | DisplayString | read-only | This object contains the last value of the optional message as described in the Result Code which caused the tunnel to disconnect. |
| stnPptpSessionStatsTable | 1.3.6.1.4.1.3551.4.1.10.1.7 | not-accessible | The PPTP session status and statistics table. | |
| stnPptpSessionStatsEntry | 1.3.6.1.4.1.3551.4.1.10.1.7.1 | not-accessible | An PPTP session interface stats entry. | |
| NUM stnPptpSessionStatsTunnelIfIndex | 1.3.6.1.4.1.3551.4.1.10.1.7.1.1 | InterfaceIndex | read-only | This object identifies the sessions associated PPTP tunnel ifIndex value. |
| NUM stnPptpSessionStatsHLIfIndex | 1.3.6.1.4.1.3551.4.1.10.1.7.1.2 | InterfaceIndex | read-only | This object identifies the ifIndex value of the interface that is either below (Lower) the tunnel (if this tunnel endpoint is a PAC) or above (Higher) the tunnel (if this tunnel endpoint is a PNS). For example this could be a DS0 ifIndex on a PAC or it would be the PPP ifIndex on the PNS. |
| I32 stnPptpSessionStatsLocalCID | 1.3.6.1.4.1.3551.4.1.10.1.7.1.3 | Integer32 | read-only | This object contains the local call identifier for the session. |
| I32 stnPptpSessionStatsRemoteCID | 1.3.6.1.4.1.3551.4.1.10.1.7.1.4 | Integer32 | read-only | This object is not used. |
| STR stnPptpSessionStatsUserName | 1.3.6.1.4.1.3551.4.1.10.1.7.1.5 | DisplayString | read-only | This object identifies the peer session name on this interface. This is typically the login name of the remote user. If the user name is unknown to the local tunnel peer then this object will contain a null string. |
| INT stnPptpSessionStatsState | 1.3.6.1.4.1.3551.4.1.10.1.7.1.6 | INTEGER | read-only | This object contains the current state of the session. |
| INT stnPptpSessionStatsCallType | 1.3.6.1.4.1.3551.4.1.10.1.7.1.7 | INTEGER | read-only | This object indicates the type of call and the role this tunnel peer is providing for this session. For example, pacIncoming(1) indicates that this tunnel peer is acting as a PAC and generated a Incoming-Call-Request to the tunnel peer (the PNS). Note that tunnel peers can be both PAC and PNS simultaneously. |
| I32 stnPptpSessionStatsCallSerialNumber | 1.3.6.1.4.1.3551.4.1.10.1.7.1.8 | Integer32 | read-only | This object contains the serial number that has been assigned to this session. |
| I32 stnPptpSessionStatsTxConnectSpeed | 1.3.6.1.4.1.3551.4.1.10.1.7.1.9 | Integer32 | read-only | This object returns the last known transmit baud rate for this session. |
| I32 stnPptpSessionStatsRxConnectSpeed | 1.3.6.1.4.1.3551.4.1.10.1.7.1.10 | Integer32 | read-only | This object returns the last known receive baud rate for this session established. |
| INT stnPptpSessionStatsCallBearerType | 1.3.6.1.4.1.3551.4.1.10.1.7.1.11 | INTEGER | read-only | This object describes the bearer type of this session. |
| INT stnPptpSessionStatsFramingType | 1.3.6.1.4.1.3551.4.1.10.1.7.1.12 | INTEGER | read-only | This object describes the framing type of this session. |
| I32 stnPptpSessionStatsPhysChanId | 1.3.6.1.4.1.3551.4.1.10.1.7.1.13 | Integer32 | read-only | This object contains the physical channel identifier for the session. |
| STR stnPptpSessionStatsDNIS | 1.3.6.1.4.1.3551.4.1.10.1.7.1.14 | DisplayString | read-only | This object identifies the Dialed Number Information String that the PAC obtained from the network for the session. If no DNIS was provided then a null string will be returned. |
| STR stnPptpSessionStatsCLID | 1.3.6.1.4.1.3551.4.1.10.1.7.1.15 | DisplayString | read-only | This object identifies the Calling Line ID that the PAC obtained from the network for the session. If no CLID was provided then a null string will be returned. |
| STR stnPptpSessionStatsSubAddress | 1.3.6.1.4.1.3551.4.1.10.1.7.1.16 | DisplayString | read-only | This object identifies the Sub Address that the PAC obtained from the network for the session. If no Sub Address was provided then a null string will be returned. |
| STR stnPptpSessionStatsPrivateGroupID | 1.3.6.1.4.1.3551.4.1.10.1.7.1.17 | DisplayString | read-only | This object identifies the Private Group Identifier used for this tunneled session. If no Private Group Identifier was provided then a null string will be returned. |
| I32 stnPptpSessionStatsLocalRWS | 1.3.6.1.4.1.3551.4.1.10.1.7.1.18 | Integer32 | read-only | This object returns the local send window size for this session. |
| I32 stnPptpSessionStatsRemoteInitialRWS | 1.3.6.1.4.1.3551.4.1.10.1.7.1.19 | Integer32 | read-only | This object returns the initial remote send window size for this session. |
| I32 stnPptpSessionStatsRemotePPD | 1.3.6.1.4.1.3551.4.1.10.1.7.1.20 | Integer32 | read-only | This object contains the Packet Processing Delay for the session. |
| C32 stnPptpSessionStatsRecvZLB | 1.3.6.1.4.1.3551.4.1.10.1.7.1.21 | Counter32 | read-only | This object returns the total number of Zero Length Body acknowlegement payload packets received for this session. |
| C32 stnPptpSessionStatsOutSequence | 1.3.6.1.4.1.3551.4.1.10.1.7.1.22 | Counter32 | read-only | This object returns the total number of packets received for this session which were received out of sequence. |
| C32 stnPptpSessionStatsSendZLB | 1.3.6.1.4.1.3551.4.1.10.1.7.1.23 | Counter32 | read-only | This object returns the total number of Zero Length Body acknowledgement packets transmitted on this session. |
| C32 stnPptpSessionStatsAckTimeouts | 1.3.6.1.4.1.3551.4.1.10.1.7.1.24 | Counter32 | read-only | This object returns the total number of acknowledgement timeouts seen on payload packets for this session. |
| G32 stnPptpSesssionStatsCurrentRemoteRWS | 1.3.6.1.4.1.3551.4.1.10.1.7.1.25 | Gauge32 | read-only | This object contains the current remote receive window size as determined by the local flow control mechanism employed. |
| I32 stnPptpSessionStatsSendSeq | 1.3.6.1.4.1.3551.4.1.10.1.7.1.26 | Integer32 | read-only | This object contains the next send sequence number for for this session. |
| I32 stnPptpSessionStatsSendSeqAck | 1.3.6.1.4.1.3551.4.1.10.1.7.1.27 | Integer32 | read-only | This object contains the send sequence number that the tunnel peer has acknowledged for the payload channel. The flow control state can be determined by subtracting the stnPptpSessionStatsSendSeq from stnPptpSessionStatsSendSeqAck and comparing this value to stnPptpSesssionStatsCurrentRemoteRWS. |
| I32 stnPptpSessionStatsRecvSeq | 1.3.6.1.4.1.3551.4.1.10.1.7.1.28 | Integer32 | read-only | This object contains the next receive sequence number expected to be received on this session. |
| I32 stnPptpSessionStatsRecvSeqAck | 1.3.6.1.4.1.3551.4.1.10.1.7.1.29 | Integer32 | read-only | This object contains the last receive sequence number that was acknowledged back to the tunnel peer for the session. |
| stnPptpTunnelMapTable | 1.3.6.1.4.1.3551.4.1.10.1.8 | not-accessible | The PPTP Tunnel index mapping table. | |
| stnPptpTunnelMapEntry | 1.3.6.1.4.1.3551.4.1.10.1.8.1 | not-accessible | An PPTP tunnel index map entry. | |
| I32 stnPptpTunnelMapLocalTID | 1.3.6.1.4.1.3551.4.1.10.1.8.1.1 | Integer32 | read-only | This object contains the local tunnel Identifier. |
| NUM stnPptpTunnelMapIfIndex | 1.3.6.1.4.1.3551.4.1.10.1.8.1.2 | InterfaceIndex | read-only | This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type PPTP. |
| stnPptpSessionMapTable | 1.3.6.1.4.1.3551.4.1.10.1.9 | not-accessible | The PPTP Session index mapping table. | |
| stnPptpSessionMapEntry | 1.3.6.1.4.1.3551.4.1.10.1.9.1 | not-accessible | An PPTP Session index map entry. | |
| NUM stnPptpSessionMapHLIfIndex | 1.3.6.1.4.1.3551.4.1.10.1.9.1.1 | InterfaceIndex | read-only | This object identifies the ifIndex value of the interface that is either below (Lower) the tunnel (if this tunnel endpoint is a PAC) or above (Higher) the tunnel (if this tunnel endpoint is a PNS). For example this could be a DS0 ifIndex on a PAC or it would be the PPP ifIndex on the PNS. |
| NUM stnPptpSessionMapTunnelIfIndex | 1.3.6.1.4.1.3551.4.1.10.1.9.1.2 | InterfaceIndex | read-only | This object identifies the sessions associated PPTP tunnel ifIndex value. |
| I32 stnPptpSessionMapLocalCID | 1.3.6.1.4.1.3551.4.1.10.1.9.1.3 | Integer32 | read-only | This object contains the local call identifier for the session. |
| stnPptpDomainMapTable | 1.3.6.1.4.1.3551.4.1.10.1.10 | not-accessible | This table provides a mapping between PPTP Domain identifiers, hostnames, and IP-ATM information | |
| stnPptpDomainMapTableEntry | 1.3.6.1.4.1.3551.4.1.10.1.10.1 | not-accessible | An entry within the STN PPTP Map Table. | |
| STR stnPptpDomainMapIdentifier | 1.3.6.1.4.1.3551.4.1.10.1.10.1.1 | DisplayString | not-accessible | PPTP Domain Identifier. |
| STR stnPptpDomainMapHostName | 1.3.6.1.4.1.3551.4.1.10.1.10.1.2 | DisplayString | read-only | The hostname that maps to the PPTP Domain Identifier. |
| STN stnPptpDomainMapType | 1.3.6.1.4.1.3551.4.1.10.1.10.1.3 | StnDomainMapType | read-only | Identifiers whether the PPTP Domain maps to an IP subnet or an ATM circuit. |
| STR stnPptpDomainMapTypeInfo | 1.3.6.1.4.1.3551.4.1.10.1.10.1.4 | DisplayString | read-only | Provides either IP or ATM specific display info. |
| stnPptpMibConformance | 1.3.6.1.4.1.3551.4.1.10.2 | |||
| stnPptpGroups | 1.3.6.1.4.1.3551.4.1.10.2.1 | |||
| stnPptpConfigGroup | 1.3.6.1.4.1.3551.4.1.10.2.1.1 | A collection of objects providing configuration information of the PPTP protocol, tunnels and sessions. | ||
| stnPptpStatsGroup | 1.3.6.1.4.1.3551.4.1.10.2.1.2 | A collection of objects providing status and statistics of the PPTP protocol, tunnels and sessions. | ||
| stnPptpDomainGroup | 1.3.6.1.4.1.3551.4.1.10.2.1.4 | A collection of objects providing configuration, status and statistics of PPTP tunnel domains. | ||
| stnPptpMappingGroup | 1.3.6.1.4.1.3551.4.1.10.2.1.5 | A collection of objects providing index mapping. | ||
| stnPptpCompliances | 1.3.6.1.4.1.3551.4.1.10.2.2 | |||
| stnPptpCompliance | 1.3.6.1.4.1.3551.4.1.10.2.2.1 | The compliance statement for SNMPv2 entities which implement the PPTP MIB. | ||
| stnPptpTraps | 1.3.6.1.4.1.3551.4.1.10.3 |
RFC description
Spring Tide Networks Point-to-Point Transport Protocol (PPTP) MIB for managing PPTP tunnel configuration and statistics (vendor-private).
Start monitoring Spring Tide Networks (Lucent) tunneling/access platform (PPTP tunnel status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.