ST2-MIB

All MIBs › ST2-MIB

Category: Generic / Unclassified

Description: Manages ST2 device configuration, interface parameters, and operational status objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ST2-MIB?

ST2-MIB is a Wellfleet (Bay Networks) vendor MIB — its OID root, stii, hangs off wfSt2Group imported from Wellfleet-ST2-MIB — that configures and reports on a router's implementation of ST-II, the Stream Protocol (RFC 1190), a resource-reservation protocol for real-time data streams. It exposes identification objects (st2AgentCopyright, st2ProtoVersion, st2FlowSpecVersion, st2AgentType indicating end-system/intermediate-system role, st2RoutingDerived), and a family of matched timeout/retry-count pairs governing each ST-II control message type — st2ToAccept/st2NAccept, st2ToConnect/st2NConnect, st2ToDisconnect/st2NDisconnect, st2ToHidAck/st2NHidAck, st2ToHidChange/st2NHidChange, st2ToNotify/st2NNotify, and st2ToRefuse/st2NRefuse. These objects reveal how aggressively the router retries ST-II control handshakes (ACCEPT, CONNECT, DISCONNECT, HID-CHANGE, NOTIFY, REFUSE) before giving up, which is central to diagnosing failed or flapping ST-II stream setups. It depends on RFC1155-SMI, RFC-1212, and RFC1213-MIB base types plus Wellfleet's own ST2 group definition. Network engineers troubleshooting ST-II reservations on Wellfleet routers can consult ST2-MIB RFC background (RFC 1190) alongside this MIB to tune its retry timers correctly.

IPNetwork Monitor allows you to monitor SNMP objects defined in ST2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet (Bay Networks) routers implementing ST-II (Stream Protocol, RFC 1190)

Monitoring Examples

An operator polls st2ToConnect and st2NConnect to see the current hop-by-hop CONNECT timeout and retry count, then correlates repeated timeouts with failed stream setups; a high number of CONNECT retries with no successful stream establishment would point to a downstream router failing to acknowledge ST-II CONNECT messages.

What Can Be Monitored

ST-II agent type and protocol/flow-spec version
CONNECT/ACCEPT/DISCONNECT timeout and retry counters
HID-CHANGE and HID-CHANGE-REQUEST timeout and retry counters
NOTIFY and REFUSE timeout and retry counters
routing-source configuration for ST-II

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks

From RFC1213-MIB

DisplayString

From Wellfleet-ST2-MIB

wfSt2Group

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
stii	1.3.6.1.4.1.18.3.5.16.1.2.5
STR st2AgentCopyright	1.3.6.1.4.1.18.3.5.16.1.2.5.1	DisplayString	read-only	provider of (company which wrote) the ST-II agent code, code release info and copyright info
STR st2ProtoVersion	1.3.6.1.4.1.18.3.5.16.1.2.5.2	DisplayString	read-only	version of ST-II running; RFC-1190 for starters
INT st2FlowSpecVersion	1.3.6.1.4.1.18.3.5.16.1.2.5.3	INTEGER	read-only	registered version number of Flow Spec
INT st2AgentType	1.3.6.1.4.1.18.3.5.16.1.2.5.4	INTEGER	read-only	whether this system performs ST-II end-system or intermediate-system functions or both
INT st2RoutingDerived	1.3.6.1.4.1.18.3.5.16.1.2.5.5	INTEGER	read-only	where does ST-II get routes from, whether IP routing tables or some other means
TIK st2ToAccept	1.3.6.1.4.1.18.3.5.16.1.2.5.6	TimeTicks	read-write	Initial hop-by-hop timeout for acknowledgment of ACCEPT
INT st2NAccept	1.3.6.1.4.1.18.3.5.16.1.2.5.7	INTEGER	read-write	number of ACCEPT retries before returning a failure
TIK st2ToConnect	1.3.6.1.4.1.18.3.5.16.1.2.5.8	TimeTicks	read-write	Initial hop-by-hop timeout for acknowledgment of CONNECT
INT st2NConnect	1.3.6.1.4.1.18.3.5.16.1.2.5.9	INTEGER	read-write	number of CONNECT retries before returning a failure
TIK st2ToDisconnect	1.3.6.1.4.1.18.3.5.16.1.2.5.10	TimeTicks	read-write	Initial hop-by-hop timeout for acknowledgment of DISCONNECT
INT st2NDisconnect	1.3.6.1.4.1.18.3.5.16.1.2.5.11	INTEGER	read-write	number of DISCONNECT retries before returning a failure
TIK st2ToHidAck	1.3.6.1.4.1.18.3.5.16.1.2.5.12	TimeTicks	read-write	Initial hop-by-hop timeout for acknowledgment of HID-CHANGE-REQUEST
INT st2NHidAck	1.3.6.1.4.1.18.3.5.16.1.2.5.13	INTEGER	read-write	number of HID-CHANGE-REQUEST retries before returning a failure
TIK st2ToHidChange	1.3.6.1.4.1.18.3.5.16.1.2.5.14	TimeTicks	read-write	Initial hop-by-hop timeout for acknowledgment of HID-CHANGE
INT st2NHidChange	1.3.6.1.4.1.18.3.5.16.1.2.5.15	INTEGER	read-write	number of HID-CHANGE retries before returning a failure
TIK st2ToNotify	1.3.6.1.4.1.18.3.5.16.1.2.5.16	TimeTicks	read-write	Initial hop-by-hop timeout for acknowledgment of NOTIFY
INT st2NNotify	1.3.6.1.4.1.18.3.5.16.1.2.5.17	INTEGER	read-write	number of NOTIFY retries before returning a failure
TIK st2ToRefuse	1.3.6.1.4.1.18.3.5.16.1.2.5.18	TimeTicks	read-write	Initial hop-by-hop timeout for acknowledgment of REFUSE
INT st2NRefuse	1.3.6.1.4.1.18.3.5.16.1.2.5.19	INTEGER	read-write	number of REFUSE retries before returning a failure
TIK st2ToReroute	1.3.6.1.4.1.18.3.5.16.1.2.5.20	TimeTicks	read-write	Timeout for receipt of ACCEPT or REFUSE from targets during failure recovery, allowing intermediate systems time to try recovery
INT st2NReroute	1.3.6.1.4.1.18.3.5.16.1.2.5.21	INTEGER	read-write	number of CONNECT retries before returning a failure from targets
TIK st2ToEnd2End	1.3.6.1.4.1.18.3.5.16.1.2.5.22	TimeTicks	read-write	End-to-end timeout for receipt of ACCEPT or REFUSE from targets by origin during failure recovery, allowing intermediate systems time to try recovery
INT st2NEnd2End	1.3.6.1.4.1.18.3.5.16.1.2.5.23	INTEGER	read-write	number of CONNECT retries before origin returns a failure from targets
INT st2NHidAbort	1.3.6.1.4.1.18.3.5.16.1.2.5.24	INTEGER	read-write	Number of rejected HID proposals before aborting the HID negotiation process
TIK st2HelloTimerHoldDown	1.3.6.1.4.1.18.3.5.16.1.2.5.25	TimeTicks	read-write	Interval that Restarted bit must be set after ST Agent restart
INT st2HelloLossFactor	1.3.6.1.4.1.18.3.5.16.1.2.5.26	INTEGER	read-write	Number of consecutively missed HELLO messages before declaring link failure to neighbor
TIK st2DefaultRecoveryTimeout	1.3.6.1.4.1.18.3.5.16.1.2.5.27	TimeTicks	read-write	Default for interval between successive HELLOs to/from active neighbors
INT st2DefaultHelloFactor	1.3.6.1.4.1.18.3.5.16.1.2.5.28	INTEGER	read-write	HELLO filtering function factor
CTR st2ScmpRcvdOctets	1.3.6.1.4.1.18.3.5.16.1.2.5.29	Counter	read-only	Total octets of SCMP messages received
CTR st2ScmpSentOctets	1.3.6.1.4.1.18.3.5.16.1.2.5.30	Counter	read-only	Total octets of SCMP messages sent
CTR st2ScmpRcvdBadTypes	1.3.6.1.4.1.18.3.5.16.1.2.5.31	Counter	read-only	Count of SCMP messages received with bad type field
CTR st2ScmpRcvdBadCks	1.3.6.1.4.1.18.3.5.16.1.2.5.32	Counter	read-only	Count of SCMP messages received with bad checksum
CTR st2ScmpSentAccepts	1.3.6.1.4.1.18.3.5.16.1.2.5.33	Counter	read-only	Count of SCMP ACCEPT messages sent
CTR st2ScmpSentAcks	1.3.6.1.4.1.18.3.5.16.1.2.5.34	Counter	read-only	Count of SCMP ACK messages sent
CTR st2ScmpSentChanges	1.3.6.1.4.1.18.3.5.16.1.2.5.35	Counter	read-only	Count of SCMP CHANGE messages sent
CTR st2ScmpSentChangeReqs	1.3.6.1.4.1.18.3.5.16.1.2.5.36	Counter	read-only	Count of SCMP CHANGE-REQUEST messages sent
CTR st2ScmpSentConnects	1.3.6.1.4.1.18.3.5.16.1.2.5.37	Counter	read-only	Count of SCMP CONNECT messages sent
CTR st2ScmpSentDisconnects	1.3.6.1.4.1.18.3.5.16.1.2.5.38	Counter	read-only	Count of SCMP DISCONNECT messages sent
CTR st2ScmpSentErrorInReqs	1.3.6.1.4.1.18.3.5.16.1.2.5.39	Counter	read-only	Count of SCMP ERROR-IN-REQUEST messages sent
CTR st2ScmpSentErrorInResps	1.3.6.1.4.1.18.3.5.16.1.2.5.40	Counter	read-only	Count of SCMP ERROR-IN-RESPONSE messages sent
CTR st2ScmpSentHellos	1.3.6.1.4.1.18.3.5.16.1.2.5.41	Counter	read-only	Count of SCMP HELLO messages sent
CTR st2ScmpSentHidApproves	1.3.6.1.4.1.18.3.5.16.1.2.5.42	Counter	read-only	Count of SCMP HID-APPROVE messages sent
CTR st2ScmpSentHidChanges	1.3.6.1.4.1.18.3.5.16.1.2.5.43	Counter	read-only	Count of SCMP HID-CHANGE messages sent
CTR st2ScmpSentHidChangeReqs	1.3.6.1.4.1.18.3.5.16.1.2.5.44	Counter	read-only	Count of SCMP HID-CHANGE-REQUEST messages sent
CTR st2ScmpSentHidRejects	1.3.6.1.4.1.18.3.5.16.1.2.5.45	Counter	read-only	Count of SCMP HID-REJECT messages sent
CTR st2ScmpSentNotifys	1.3.6.1.4.1.18.3.5.16.1.2.5.46	Counter	read-only	Count of SCMP NOTIFY messages sent
CTR st2ScmpSentRefuses	1.3.6.1.4.1.18.3.5.16.1.2.5.47	Counter	read-only	Count of SCMP REFUSE messages sent
CTR st2ScmpSentStatus	1.3.6.1.4.1.18.3.5.16.1.2.5.48	Counter	read-only	Count of SCMP STATUS messages sent
CTR st2ScmpSentStatusResps	1.3.6.1.4.1.18.3.5.16.1.2.5.49	Counter	read-only	Count of SCMP STATUS-RESPONSE messages sent
CTR st2ScmpRcvdAccepts	1.3.6.1.4.1.18.3.5.16.1.2.5.50	Counter	read-only	Count of SCMP ACCEPT messages received
CTR st2ScmpRcvdAcks	1.3.6.1.4.1.18.3.5.16.1.2.5.51	Counter	read-only	Count of SCMP ACK messages received
CTR st2ScmpRcvdChanges	1.3.6.1.4.1.18.3.5.16.1.2.5.52	Counter	read-only	Count of SCMP CHANGE messages received
CTR st2ScmpRcvdChangeReqs	1.3.6.1.4.1.18.3.5.16.1.2.5.53	Counter	read-only	Count of SCMP CHANGE-REQUEST messages received
CTR st2ScmpRcvdConnects	1.3.6.1.4.1.18.3.5.16.1.2.5.54	Counter	read-only	Count of SCMP CONNECT messages received
CTR st2ScmpRcvdDisconnects	1.3.6.1.4.1.18.3.5.16.1.2.5.55	Counter	read-only	Count of SCMP DISCONNECT messages received
CTR st2ScmpRcvdErrorInReqs	1.3.6.1.4.1.18.3.5.16.1.2.5.56	Counter	read-only	Count of SCMP ERROR-IN-REQUEST messages received
CTR st2ScmpRcvdErrorInResps	1.3.6.1.4.1.18.3.5.16.1.2.5.57	Counter	read-only	Count of SCMP ERROR-IN-RESPONSE messages received
CTR st2ScmpRcvdHellos	1.3.6.1.4.1.18.3.5.16.1.2.5.58	Counter	read-only	Count of SCMP HELLO messages received
CTR st2ScmpRcvdHidApproves	1.3.6.1.4.1.18.3.5.16.1.2.5.59	Counter	read-only	Count of SCMP HID-APPROVE messages received
CTR st2ScmpRcvdHidChanges	1.3.6.1.4.1.18.3.5.16.1.2.5.60	Counter	read-only	Count of SCMP HID-CHANGE messages received
CTR st2ScmpRcvdHidChangeReqs	1.3.6.1.4.1.18.3.5.16.1.2.5.61	Counter	read-only	Count of SCMP HID-CHANGE-REQUEST messages received
CTR st2ScmpRcvdHidRejects	1.3.6.1.4.1.18.3.5.16.1.2.5.62	Counter	read-only	Count of SCMP HID-REJECT messages received
CTR st2ScmpRcvdNotifys	1.3.6.1.4.1.18.3.5.16.1.2.5.63	Counter	read-only	Count of SCMP NOTIFY messages received
CTR st2ScmpRcvdRefuses	1.3.6.1.4.1.18.3.5.16.1.2.5.64	Counter	read-only	Count of SCMP REFUSE messages received
CTR st2ScmpRcvdStatus	1.3.6.1.4.1.18.3.5.16.1.2.5.65	Counter	read-only	Count of SCMP STATUS messages received
CTR st2ScmpRcvdStatusResps	1.3.6.1.4.1.18.3.5.16.1.2.5.66	Counter	read-only	Count of SCMP STATUS-RESPONSE messages received
OCT st2ScmpRcvdErrorSnap	1.3.6.1.4.1.18.3.5.16.1.2.5.67	OCTET STRING	read-only	Contents from last SCMP packet received with error
TIK st2ScmpRcvdBadTypeTime	1.3.6.1.4.1.18.3.5.16.1.2.5.68	TimeTicks	read-only	Time that last SCMP packet was received with bad Type field
TIK st2ScmpRcvdBadCksTime	1.3.6.1.4.1.18.3.5.16.1.2.5.69	TimeTicks	read-only	Time that last SCMP packet was received with bad checksum
CTR st2OriginOpens	1.3.6.1.4.1.18.3.5.16.1.2.5.70	Counter	read-only	Count of streams opened with this agent as origin, but they may have since been closed
CTR st2IntermedOpens	1.3.6.1.4.1.18.3.5.16.1.2.5.71	Counter	read-only	Count of streams opened with this agent as intermediate system
CTR st2TargetOpens	1.3.6.1.4.1.18.3.5.16.1.2.5.72	Counter	read-only	Count of streams opened with this agent as target (destination) - may also be counted in intermediate
CTR st2FailOpens	1.3.6.1.4.1.18.3.5.16.1.2.5.73	Counter	read-only	Count of stream opens attempted which did not complete
CTR st2AcceptTimeouts	1.3.6.1.4.1.18.3.5.16.1.2.5.74	Counter	read-only	Count of stream opens failed because ACCEPT did not get acknowledged
CTR st2ParamChangeFails	1.3.6.1.4.1.18.3.5.16.1.2.5.75	Counter	read-only	Count of stream parameter changes which failed
GAU st2NumStreamEntries	1.3.6.1.4.1.18.3.5.16.1.2.5.76	Gauge	read-only	Count of stream table entries (extent of streams table)
GAU st2NumOpenStreams	1.3.6.1.4.1.18.3.5.16.1.2.5.77	Gauge	read-only	Count of streams which are open (number of table entries for them)
GAU st2NumOpenOriginStreams	1.3.6.1.4.1.18.3.5.16.1.2.5.78	Gauge	read-only	Count of current open streams which were originated here
GAU st2NumHops	1.3.6.1.4.1.18.3.5.16.1.2.5.79	Gauge	read-only	Count of Hop entries (extent of next-hop table)
GAU st2NumNeighbors	1.3.6.1.4.1.18.3.5.16.1.2.5.80	Gauge	read-only	Count of Neighbor entries (extent of neighbor table)
GAU st2NumTargets	1.3.6.1.4.1.18.3.5.16.1.2.5.81	Gauge	read-only	Count of target entries (extent of target table)
GAU st2NumGroups	1.3.6.1.4.1.18.3.5.16.1.2.5.82	Gauge	read-only	count of group entries (extent of groups table)
GAU st2NumSubgroups	1.3.6.1.4.1.18.3.5.16.1.2.5.83	Gauge	read-only	Count of subgroup entries (extent of subgroups table)
CTR st2RouteFailures	1.3.6.1.4.1.18.3.5.16.1.2.5.84	Counter	read-only	Count of stream opens failed because no route found
CTR st2RouteLoops	1.3.6.1.4.1.18.3.5.16.1.2.5.85	Counter	read-only	Count of stream opens failed because route inconsistency found, e.g. potential or actual loop
CTR st2ScmpRetrans	1.3.6.1.4.1.18.3.5.16.1.2.5.86	Counter	read-only	count of SCMP control timeout and retransmissions
st2StreamTable	1.3.6.1.4.1.18.3.5.16.1.2.5.87		not-accessible	table of information for each stream
st2StreamEntry	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1		not-accessible
OCT st2StreamName	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.1	OCTET STRING	read-only	internal format name of this stream
IP st2StreamPrevHopAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.2	IpAddress	read-only	previous hop entry which feeds data to this node
INT st2StreamPrevHopVlid	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.3	INTEGER	read-only	virtual link identifier of the previous hop
TIK st2StreamStartTime	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.4	TimeTicks	read-only	timestamp when this stream was first entered in this table
INT st2StreamState	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.5	INTEGER	read-only	current state of this stream at this node
TIK st2StreamStateTime	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.6	TimeTicks	read-only	time this stream entered its current state
INT st2StreamRole	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.7	INTEGER	read-only	role that this agent performs for this stream
OCT st2StreamGroup	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.8	OCTET STRING	read-only	group (if any) which this stream is in
GAU st2StreamNumSubgroups	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.9	Gauge	read-only	number of subgroups which this stream is in (get info from subgroup table)
GAU st2StreamNumNextHops	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.10	Gauge	read-only	number of nexthops to which this stream feeds data (get info from hop table)
GAU st2StreamNumTargets	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.11	Gauge	read-only	number of targets to which this stream feeds data (get info from target table)
CTR st2StreamRefuses	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.12	Counter	read-only	number of times this stream has suffered the ignominy of getting changes refused
CTR st2StreamFlowspecChanges	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.13	Counter	read-only	number of times this flowspec has been changed over the duration of this stream.
INT st2StreamFlowPrecedence	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.14	INTEGER	read-only	flowspec precedence field (8 bits) -- NOTE: THIS MOVES DOWN BELOW ERROR RATE
INT st2StreamFlowDutyFactor	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.15	INTEGER	read-only	flowspec dutyfactor field (8 bits)
INT st2StreamFlowErrorRate	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.16	INTEGER	read-only	flowspec error rate field (8 bits)
INT st2StreamFlowReliability	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.17	INTEGER	read-only	flowspec reliability field (8 bits)
INT st2StreamFlowTradeoffs	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.18	INTEGER	read-only	flowspec tradeoffs field (16 bits)
INT st2StreamFlowRecoveryTimeout	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.19	INTEGER	read-only	flowspec recovery timeout field (16 bits)
INT st2StreamFlowLimitOnCost	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.20	INTEGER	read-only	flowspec limit on cost field (16 bits)
INT st2StreamFlowLimitOnDelay	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.21	INTEGER	read-only	flowspec limit on delay field (16 bits)
INT st2StreamFlowLimitOnPduBytes	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.22	INTEGER	read-only	flowspec LIMIT ON PDU BYTES (pdu size in octets) field (16 bits)
INT st2StreamFlowLimitOnPduRate	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.23	INTEGER	read-only	flowspec limit on pdu rate field (16 bits)
INT st2StreamFlowMinBytesXRate	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.24	INTEGER	read-only	flowspec min bytes x rate field (product gives bandwidth in bytes per 10 seconds; divide by 1250 for Kbits per second) (32 bits)
INT st2StreamFlowMeanDelay	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.25	INTEGER	read-only	flowspec accumulated mean delay field (32 bits)
INT st2StreamFlowDelayVariance	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.26	INTEGER	read-only	flowspec accumulated delay variance field (32 bits)
INT st2StreamFlowDesPduBytes	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.27	INTEGER	read-only	flowspec desired pdu bytes (size) field (16 bits)
INT st2StreamFlowDesPduRate	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.28	INTEGER	read-only	flowspec desired pdu rate field (16 bits)
INT st2StreamOptionPtp	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.29	INTEGER	read-only	true if POINT TO POINT option specified on this stream
INT st2StreamOptionFdx	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.30	INTEGER	read-only	true if FULL DUPLEX option specified on this stream; reverse stream is the same but takes a separate stream table entry in this MIB
INT st2StreamOptionRecover	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.31	INTEGER	read-only	false if NO RECOVERY option specified for this stream
INT st2StreamOptionReverseCharge	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.32	INTEGER	read-only	true if REVERSE CHARGE option specified for this stream
INT st2StreamOptionTimestamp	1.3.6.1.4.1.18.3.5.16.1.2.5.87.1.33	INTEGER	read-only	the TIMESTAMP option specified for this stream
st2HopTable	1.3.6.1.4.1.18.3.5.16.1.2.5.88		not-accessible	table of information for each prev- or next-hop
st2HopEntry	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1		not-accessible
INT st2HopHid	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.1	INTEGER	read-only	HID which this node has negotiated with this next hop (and all others on a multicast)
INT st2HopMyVlid	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.2	INTEGER	read-only	VLID (table index or something) by which this next hop addresses me
INT st2HopYourVlid	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.3	INTEGER	read-only	VLID (table index or something) by which I address this next hop
INT st2HopState	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.4	INTEGER	read-only	state of negotiation for this stream to this hop
TIK st2HopStateTime	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.5	TimeTicks	read-only	time this state was entered
GAU st2HopNumTargets	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.6	Gauge	read-only	number of targets reached via this next hop
IP st2HopMcastAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.7	IpAddress	read-only	multicast address, if any, used to reach this hop and others on same net (for current ST-II, this does not work here)(this should be an IP multicast address, or some magic IP address which translates into local-net multicast
INT st2HopErrorCode	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.8	INTEGER	read-only	refuse code or other error indicator received from next hop
IP st2HopDetectorAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.9	IpAddress	read-only	detector address field from error message received from next hop
IP st2HopNeighborAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.10	IpAddress	read-only	ip address of neighbor which is this next hop (it has the info rfc1190 to all next hops for streams which go through that node)
OCT st2HopStreamName	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.11	OCTET STRING	read-only	back pointer to stream for which this is a hop
CTR st2HopPkts	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.12	Counter	read-only	count of packets received from this hop in this stream, or sent in this stream to this hop, depending on st2HopRole
CTR st2HopOctets	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.13	Counter	read-only	count of octets received from this hop in this stream, or sent in this stream to this hop, depending on st2HopRole
CTR st2HopDiscards	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.14	Counter	read-only	count of packets received from this hop in this stream and not processed, or not able to be sent in this stream to this hop, depending on st2HopRole
INT st2HopIpEncap	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.15	INTEGER	read-only	true if data for this stream is sent with IP encapsulation to this next hop
IP st2HopIpAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.16	IpAddress	read-only	if ip encapsulation is on, this is the direct (local) next hop IP address of the next router on the path. the ST agent next hop can be further away. Implementations might store this so as to bypass the IP routing function.
INT st2HopRole	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.17	INTEGER	read-only	tells whether this hop entry is a previous-hop for this stream or a next-hop. this is to help identify whether the packet, octet and discard counters are for input from a prev-hop or output to a next-hop.
INT st2HopInterfaceIndex	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.18	INTEGER	read-only	Interface Index
TIK st2HopErrorTime	1.3.6.1.4.1.18.3.5.16.1.2.5.88.1.19	TimeTicks	read-only	Time when refuse code or other error occurs
st2NeighborTable	1.3.6.1.4.1.18.3.5.16.1.2.5.89		not-accessible	table of information for each neighbor common info
st2NeighborEntry	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1		not-accessible
IP st2NeighborAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.1	IpAddress	read-only	address of neighbor ST Agent serving as nexthop or previous hop for one or more streams
INT st2NeighborState	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.2	INTEGER	read-only	state of neighbor ST Agent w.r.t. hellos and data
TIK st2NeighborStateTime	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.3	TimeTicks	read-only	time entered this state of neighbor ST Agent
GAU st2NeighborNumHops	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.4	Gauge	read-only	number of hops using this neighbor for next or prev
TIK st2NeighborHelloTimer	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.5	TimeTicks	read-only	min of hello times based on RecoveryTimeout for all streams via this neighbor - or possibly default. Note: ST specifies this in milliseconds
TIK st2NeighborHelloRcvdTime	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.6	TimeTicks	read-only	timestamp when most recent hello received from this neighbor
TIK st2NeighborDataRcvdTime	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.7	TimeTicks	read-only	timestamp when most recent ST data received from this neighbor - this may be updated infrequently, perhaps every couple of seconds
INT st2NeighborAckRequested	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.8	INTEGER	read-only	I have requested an ACK from this neighbor, still outstanding - for RTT estimation
INT st2NeighborRestarted	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.9	INTEGER	read-only	hello received from this neighbor with the restart bit on indicating neighbor has restarted recently
CTR st2NeighborSentHellos	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.10	Counter	read-only	count of hellos sent to this neighbor
CTR st2NeighborRcvdHellos	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.11	Counter	read-only	count of hellos received from this neighbor
CTR st2NeighborMissedHellos	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.12	Counter	read-only	count of hellos expected which were not received from this neighbor
TIK st2NeighborRoundTripTime	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.13	TimeTicks	read-only	current estimate of round trip time to this neighbor based on hello exchanges
INT st2NeighborInterfaceIdx	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.14	INTEGER	read-only	internal index of interface which reaches this neighbor
CTR st2NeighborStBadMsgs	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.15	Counter	read-only	count of bad stream data messages received from this neighbor
CTR st2NeighborScmpBadMsgs	1.3.6.1.4.1.18.3.5.16.1.2.5.89.1.16	Counter	read-only	count of bad stream control messages received from this neighbor
st2TargetTable	1.3.6.1.4.1.18.3.5.16.1.2.5.90		not-accessible	table of information for each target
st2TargetEntry	1.3.6.1.4.1.18.3.5.16.1.2.5.90.1		not-accessible
IP st2TargetAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.90.1.1	IpAddress	read-only	ip address of target
IP st2TargetHop	1.3.6.1.4.1.18.3.5.16.1.2.5.90.1.2	IpAddress	read-only	ip address of the nexthop which gets to this target
OCT st2TargetStreamName	1.3.6.1.4.1.18.3.5.16.1.2.5.90.1.3	OCTET STRING	read-only	name of the stream this target is a member of
st2GroupTable	1.3.6.1.4.1.18.3.5.16.1.2.5.91		not-accessible	table of information for each group
st2GroupEntry	1.3.6.1.4.1.18.3.5.16.1.2.5.91.1		not-accessible
OCT st2GroupName	1.3.6.1.4.1.18.3.5.16.1.2.5.91.1.1	OCTET STRING	read-only	the ST-II name of this group of streams
INT st2GroupId	1.3.6.1.4.1.18.3.5.16.1.2.5.91.1.2	INTEGER	read-only	a group identifier
GAU st2GroupNumStreams	1.3.6.1.4.1.18.3.5.16.1.2.5.91.1.3	Gauge	read-only	number of streams which are members of this group
GAU st2GroupNumSubgroups	1.3.6.1.4.1.18.3.5.16.1.2.5.91.1.4	Gauge	read-only	number of subgroups in this group
st2SubgroupTable	1.3.6.1.4.1.18.3.5.16.1.2.5.92		not-accessible	table of information for each sub-group
st2SubgroupEntry	1.3.6.1.4.1.18.3.5.16.1.2.5.92.1		not-accessible
OCT st2SubgroupGroup	1.3.6.1.4.1.18.3.5.16.1.2.5.92.1.1	OCTET STRING	read-only	group which this subgroup is a member
GAU st2SubgroupNumStreams	1.3.6.1.4.1.18.3.5.16.1.2.5.92.1.2	Gauge	read-only	number of streams in this subgroup
INT st2SubgroupIndex	1.3.6.1.4.1.18.3.5.16.1.2.5.92.1.3	INTEGER	read-only	internal index into sub-group table
st2InterfaceTable	1.3.6.1.4.1.18.3.5.16.1.2.5.93		not-accessible	table of information for each interface
st2InterfaceEntry	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1		not-accessible
INT st2InterfaceIndex	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.1	INTEGER	read-only	interface index of this interface - like ifIndex from main MIB
GAU st2InterfaceNumInStreams	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.2	Gauge	read-only	number of streams coming in this interface
GAU st2InterfaceNumOutStreams	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.3	Gauge	read-only	number of streams going out this interface
GAU st2InterfaceNumNeighbors	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.4	Gauge	read-only	number of neighbors on this interface being used as prev or next hop
GAU st2InterfaceInBwReserved	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.5	Gauge	read-only	total of flowspec (bytes x rate) into this interface in units of bits-per-second
GAU st2InterfaceInBwReservable	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.6	Gauge	read-write	amount of bandwidth remaining able to be reserved for input into this interface in units of bits-per-second
GAU st2InterfaceOutBwReserved	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.7	Gauge	read-only	total of flowspec (bytes x rate) out of this interface in units of bits-per-second
GAU st2InterfaceOutBwReservable	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.8	Gauge	read-write	amount of bandwidth remaining able to be reserved for output out of this interface in units of bits-per-second
CTR st2InterfaceTotRcvdPkts	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.9	Counter	read-only	Count of stream data packets received overall (for streams both current and expired)
CTR st2InterfaceTotSentPkts	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.10	Counter	read-only	Count of stream data packets sent overall (??) including replications for multiple output interfaces and multiple next-hops when multicast is not used ( make this per interface ??)
CTR st2InterfaceTotRcvdOctets	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.11	Counter	read-only	Count of stream data octets received overall
CTR st2InterfaceTotSentOctets	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.12	Counter	read-only	Count of stream data octets sent
CTR st2InterfaceRcvdHdrErrors	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.13	Counter	read-only	Count of stream data packets received with header format errors
CTR st2InterfaceRcvdHidErrors	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.14	Counter	read-only	Count of stream data packets received with errors in HID
CTR st2InterfaceRcvdLenErrors	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.15	Counter	read-only	Count of stream data packets received with errors in length
TIK st2InterfaceRcvdHdrErrorTime	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.16	TimeTicks	read-only	Time of last stream data packet received with header format errors
TIK st2InterfaceRcvdHidErrorTime	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.17	TimeTicks	read-only	Time of last stream data packet received with errors in HID
TIK st2InterfaceRcvdLenErrorTime	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.18	TimeTicks	read-only	Time of last stream data packet received with errors in length
STR st2InterfaceRcvdErrorSnap	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.19	DisplayString	read-only	Contents from last stream data packet received with error
CTR st2InterfaceRcvdPktDrops	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.20	Counter	read-only	Count of stream data packets received and dropped due to resource limitations
CTR st2InterfaceSentPktDrops	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.21	Counter	read-only	Count of stream data packets sent and dropped due to resource limitations
IP st2InterfaceIpAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.93.1.22	IpAddress	read-only	Interface Ip address
OCT st2LastCloseStreamName	1.3.6.1.4.1.18.3.5.16.1.2.5.94	OCTET STRING	read-only	Last close stream name
IP st2LastClosePrevHopIpAddr	1.3.6.1.4.1.18.3.5.16.1.2.5.95	IpAddress	read-only	Last close previous hop Ip address
INT st2LastCloseReasonCode	1.3.6.1.4.1.18.3.5.16.1.2.5.96	INTEGER	read-only	Reason code field from the last close message
IP st2LastCloseDetectorIpAddress	1.3.6.1.4.1.18.3.5.16.1.2.5.97	IpAddress	read-only	detector address from the last close message
TIK st2LastCloseTime	1.3.6.1.4.1.18.3.5.16.1.2.5.98	TimeTicks	read-only	sysuptime when the last close received

RFC description

RFC 1190 ST-II (Stream Protocol II) MIB for managing stream protocol configuration, flow specifications, and agent information on ST-II capable systems.

Start monitoring Wellfleet (Bay Networks) router implementing ST-II Stream Protocol (RFC 1190) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ST2-MIB

What Is ST2-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description