SS-OPT-MIB

All MIBs › SS-OPT-MIB

Category: Generic / Unclassified

Description: Manages SS protocol optional feature configuration and associated operational parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SS-OPT-MIB?

Available metadata for this module is very limited — only a short description of managing optional feature configuration for an unspecified 'SS' protocol, with no module description text or sample object names supplied. Based on the short description, it appears to expose configuration of optional protocol features and associated operational parameters, rather than a clearly identified set of data categories. Any monitoring value would likely be about software/feature-configuration state (which optional features are enabled and how they're parameterized) rather than physical hardware status, but this can't be confirmed from the data available. There is insufficient information here to identify a dependency on any specific companion standard or base MIB. Likewise, the vendor and target device/platform for this MIB cannot be determined from what was provided, so the SS-OPT-MIB reference itself remains the best source for confirming its actual object definitions and behavior.

IPNetwork Monitor allows you to monitor SNMP objects defined in SS-OPT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

insufficient information to identify a specific device or vendor

Monitoring Examples

No object or table names, and no substantive module description, were provided for this module, so a concrete monitoring scenario cannot be grounded in real object names. Based on the short description alone, it would expose scalar objects for enabling/disabling optional 'SS' protocol features and configuring their operational parameters.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

enterprises

OIDs

OID symbolic	OID numeric	Type	Access	Description
codex	1.3.6.1.4.1.449
cdxProductSpecific	1.3.6.1.4.1.449.2
cdx6500	1.3.6.1.4.1.449.2.1
cdx6500Configuration	1.3.6.1.4.1.449.2.1.2
cdx6500CfgGeneralGroup	1.3.6.1.4.1.449.2.1.2.2
cdx6500GCTLSSTable	1.3.6.1.4.1.449.2.1.2.2.14		not-accessible	A list of Configuration parameters that makeup the Switched Service/LBU Table.
cdx6500SSCfgEntry	1.3.6.1.4.1.449.2.1.2.2.14.1		not-accessible	Each entry contains the Configuration parameters for each switched Service/backup link.
INT cdx6500SSEntryNumber	1.3.6.1.4.1.449.2.1.2.2.14.1.1	INTEGER	read-only	This identifies the particular Switched Service/LBU Table entry being configured. The number of instances defined by this entry depends on the configured value of the Maximum Switch Service Entry parameter in the Node record (upto a maximum of 1024 entries). If this value is 0, no switched Service/backup links may be configured i.e. this table will be empty.
STR cdx6500SSDestinationName	1.3.6.1.4.1.449.2.1.2.2.14.1.2	DisplayString	read-only	This is a unique name that identifies this entry.
STR cdx6500SSCfgMonitoredPort	1.3.6.1.4.1.449.2.1.2.2.14.1.3	DisplayString	read-only	The X.25 port to be monitored for link failure. This is the port whose calls are rerouted in the event of port failure. The format must be the following: X25-n, FRI-nSm OR BRI-nCp where n is the port number, m is the station number and p is BRI channel number.
STR cdx6500SSCfgRestoralPort	1.3.6.1.4.1.449.2.1.2.2.14.1.4	DisplayString	read-only	This is the port or channel that acts as the backup when there is a port failure on the port specified by the parameter Monitored port, or primary destination port (activated by call) The format must be the following: X25-n or BRI-nCm, where n is the port number and m is the channel number.
STR cdx6500SSDialSequence	1.3.6.1.4.1.449.2.1.2.2.14.1.5	DisplayString	read-only	This specifies the telephone numbers that will be dialed when the backup port is activated. To enter your own telephone number, use any combination of the following characters: 0-9 Decimal : Wait Tone Seperator 4 P or p Dialing to be continued in PULSE mode. T or t Dialing to be continued in DTMF mode. & Flash To have the modem dial one of its pre-programmed telephone numbers, enter: #n where 'n' identifies the pre-programmed telephone number stored in the modem.
INT cdx6500SSActivationMode	1.3.6.1.4.1.449.2.1.2.2.14.1.6	INTEGER	read-only	This specifies how the switched service/backup port will be activated. fail - Activate the backup port upon link failure. call - Activate the backup port upon a call request. either - Activate the backup port upon link failure or a call request. newvalFail - same functionality as 'fail', new enumeration added for RFC1155 compatibility.
INT cdx6500SSDeactivationMode	1.3.6.1.4.1.449.2.1.2.2.14.1.7	INTEGER	read-only	This specifies how the switched service/backup port is deactivated after the original link is up. none - Backup port can only be deactivated by operator intervention. busyOut - The backup port is deactivated after all the calls on that port are cleared for a predetermined amount of time. This substitutes the value assigned to the parameter Link Hold Time with the value assigned to the parameter Idle Disconnect Time in the X.25 Port Record. The Idle Disconnect Time will then work as described in the Operators Guide. When Deactivation Mode = BUSY OUT and Link Hold Time = 0 (zero) the overall effect is the same as setting this entry to NONE. imm - The backup link is terminated IMMediately when the monitored port is restored regardless of how many calls are present. newvalNone - same functionality as 'none', new enumeration added for RFC1155 compatibility.
INT cdx6500SSLinkHoldTime	1.3.6.1.4.1.449.2.1.2.2.14.1.8	INTEGER	read-only	This replaces the value of the parameter Idle Disconnect Timer in the X.25 Port Record and specifies how long (in seconds) the backup link remains active after the original link is back up.
STR cdx6500SSOutBoundPass	1.3.6.1.4.1.449.2.1.2.2.14.1.9	DisplayString	read-only	This is the password used by the remote station to determine if dial access is authorized.
INT cdx6500SSRedialTime	1.3.6.1.4.1.449.2.1.2.2.14.1.10	INTEGER	read-only	This is the time in seconds between dial attempts when bringing up a switched service call.
INT cdx6500SSRedialCounter	1.3.6.1.4.1.449.2.1.2.2.14.1.11	INTEGER	read-only	This parameter is used to specify the number of times that the Switched Service will attempt to redial when redial timer is expired. A value of zero will allow unlimited attempts.
INT cdx6500SSSecurityMode	1.3.6.1.4.1.449.2.1.2.2.14.1.12	INTEGER	read-only	This specifies under what conditions the port/channel authorizes call request. none - A call request not be rejected based on password of calling party id validation. password - A call request will only be accepted if the password it provides matches the switched services password configured in the node record. callingId - A call request will only be accepted if the calling party id of the caller matches one of the entries found in the calling party id table. both - A call request is accepted only if both the password and the calling party id are valid. newvalNone - same functionality as 'none', new enumeration added for RFC1155 compatibility.
INT cdx6500SSSetupTime	1.3.6.1.4.1.449.2.1.2.2.14.1.13	INTEGER	read-only	This is the time in seconds the monitor port(s) are given to come up after node boot before the backup port is activated.
STR cdx6500SSCfgMonitoredPort2	1.3.6.1.4.1.449.2.1.2.2.14.1.14	DisplayString	read-only	The X.25 port to be monitored for link failure. This is the port whose calls are rerouted in the event of port failure. The format must be the following: X25-n, FRI-nSm OR BRI-nCp where n is the port number, m is the station number and p is BRI channel number.
STR cdx6500SSCfgMonitoredPort3	1.3.6.1.4.1.449.2.1.2.2.14.1.15	DisplayString	read-only	The X.25 port to be monitored for link failure. This is the port whose calls are rerouted in the event of port failure. The format must be the following: X25-n, FRI-nSm OR BRI-nCp where n is the port number, m is the station number and p is BRI channel number.
STR cdx6500SSCfgMonitoredPort4	1.3.6.1.4.1.449.2.1.2.2.14.1.16	DisplayString	read-only	The X.25 port to be monitored for link failure. This is the port whose calls are rerouted in the event of port failure. The format must be the following: X25-n, FRI-nSm OR BRI-nCp where n is the port number, m is the station number and p is BRI channel number.
STR cdx6500SSDialSequence2	1.3.6.1.4.1.449.2.1.2.2.14.1.17	DisplayString	read-only	This specifies the telephone numbers that will be dialed when the backup port is activated. To enter your own telephone number, use any combination of the following characters: 0-9 Decimal : Wait Tone Seperator 4 P or p Dialing to be continued in PULSE mode. T or t Dialing to be continued in DTMF mode. & Flash To have the modem dial one of its pre-programmed telephone numbers, enter: #n where 'n' identifies the pre-programmed telephone number stored in the modem.
STR cdx6500SSDialSequence3	1.3.6.1.4.1.449.2.1.2.2.14.1.18	DisplayString	read-only	This specifies the telephone numbers that will be dialed when the backup port is activated. To enter your own telephone number, use any combination of the following characters: 0-9 Decimal : Wait Tone Seperator 4 P or p Dialing to be continued in PULSE mode. T or t Dialing to be continued in DTMF mode. & Flash To have the modem dial one of its pre-programmed telephone numbers, enter: #n where 'n' identifies the pre-programmed telephone number stored in the modem.
STR cdx6500SSDialSequence4	1.3.6.1.4.1.449.2.1.2.2.14.1.19	DisplayString	read-only	This specifies the telephone numbers that will be dialed when the backup port is activated. To enter your own telephone number, use any combination of the following characters: 0-9 Decimal : Wait Tone Seperator 4 P or p Dialing to be continued in PULSE mode. T or t Dialing to be continued in DTMF mode. & Flash To have the modem dial one of its pre-programmed telephone numbers, enter: #n where 'n' identifies the pre-programmed telephone number stored in the modem.
cdx6500CallIDTable	1.3.6.1.4.1.449.2.1.2.2.18		not-accessible	A list of Configuration calling ID that makeup the Calling ID Table.
cdx6500CallIDEntry	1.3.6.1.4.1.449.2.1.2.2.18.1		not-accessible	Each entry contains the Configuration Calling ID.
INT cdx6500CallIDEntryNumber	1.3.6.1.4.1.449.2.1.2.2.18.1.1	INTEGER	read-only	This is not a configurable parameter. This identifies the particular calling ID Table entry being configured by the other parameters in the record.
STR cdx6500CallIDString	1.3.6.1.4.1.449.2.1.2.2.18.1.2	DisplayString	read-only	Each calling id entry is a numeric value which may contain periods or dashes. Only calls matching these ids will be allowed when calling id security is enabled.
cdx6500Statistics	1.3.6.1.4.1.449.2.1.3
cdx6500StatOtherStatsGroup	1.3.6.1.4.1.449.2.1.3.2
cdx6500OSTSSTable	1.3.6.1.4.1.449.2.1.3.2.3		not-accessible	A list of statistics parameters for the Switch Service/Link Backup port,station,and channel.
cdx6500SSStatEntry	1.3.6.1.4.1.449.2.1.3.2.3.1		not-accessible	Each entry on this table pertains to the Switched Service/Link Backup port,station and channel, and can be accessed using the following index: the switched/backup port number, switched/backup station number and the switched/backup channel number.
INT cdx6500SSStatRestoralPort	1.3.6.1.4.1.449.2.1.3.2.3.1.1	INTEGER	read-only	This is the backup port number, used as an index to access Switched Service/LBU statistics.
STR cdx6500SSPortType	1.3.6.1.4.1.449.2.1.3.2.3.1.2	DisplayString	read-only	The port type of the backup port.
STR cdx6500SSConnType	1.3.6.1.4.1.449.2.1.3.2.3.1.3	DisplayString	read-only	The connection type of the backup port.
INT cdx6500SSStatus	1.3.6.1.4.1.449.2.1.3.2.3.1.4	INTEGER	read-only	The status of the backup port. newvalDown - same functionality as 'down', new enumeration added for RFC1155 compatibility.
INT cdx6500SSReason	1.3.6.1.4.1.449.2.1.3.2.3.1.5	INTEGER	read-only	The reason that the backup port is active. none : Backup port is deactivated. call : A call request was made on the backup port. fail : Due to a link failure on the monitored port. remote : A call request was made to the backup port. ctp : Backup port was activated from the control terminal. newvalNone : same functionality as 'none', new enumeration added for RFC1155 compatibility.
INT cdx6500SSRedial	1.3.6.1.4.1.449.2.1.3.2.3.1.6	INTEGER	read-only	This parameter is used to specify the number of times that the Switched Service will attempt to redial when the redial timer is expired. A value of zero will allow unlimited attempts.
STR cdx6500SSLastActivated	1.3.6.1.4.1.449.2.1.3.2.3.1.7	DisplayString	read-only	The last time the backup port was activated.
STR cdx6500SSLastPhoneDialed	1.3.6.1.4.1.449.2.1.3.2.3.1.8	DisplayString	read-only	The phone number dialed the last time the backup port was activated.
cdx6500OSTSSMonTable	1.3.6.1.4.1.449.2.1.3.2.4		not-accessible	A list of statistics parameters for the Link Backup's monitored port.
cdx6500SSMonStatEntry	1.3.6.1.4.1.449.2.1.3.2.4.1		not-accessible	Each entry on this table pertains to one of the monitored ports/station/channel that is monitored by the backup port/ station/channel and should be accessed using the following index, * the backup port number * the backup station number * the backup channel number * the monitored port * the monitored station * the monitored channel.
INT cdx6500SSStatRestMonPort	1.3.6.1.4.1.449.2.1.3.2.4.1.1	INTEGER	read-only	This is the backup port number, used as a primary index to access monitored port statistics.
INT cdx6500SSStatMonitoredPort	1.3.6.1.4.1.449.2.1.3.2.4.1.2	INTEGER	read-only	This is the port being monitored by the backup port, used as a secondary index to access monitored port statistics.
INT cdx6500SSMonPortState	1.3.6.1.4.1.449.2.1.3.2.4.1.3	INTEGER	read-only	State of the monitored port. newvalDown : same functionality as 'down', new enumeration added for RFC1155 compatibility.
STR cdx6500SSRestPhoneNum	1.3.6.1.4.1.449.2.1.3.2.4.1.4	DisplayString	read-only	Phone number that the backup port will dial when a monitored port has a link failure.

RFC description

SNMP MIB for managing optical parameters on Dense Wavelength Division Multiplexing (DWDM) interfaces. Provides objects for monitoring and configuring optical signal characteristics and performance metrics.

Start monitoring insufficient information to identify a specific device or vendor (optional SS-protocol feature configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SS-OPT-MIB

What Is SS-OPT-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description