SONOMASYSTEMS-SONOMA-ATM-T1-MIB

All MIBs › SONOMASYSTEMS-SONOMA-ATM-T1-MIB

Category: ATM Interface Management, SonomaSystems ATM WAN Management

Description: Manages SonomaSystems ATM T1 interface configuration, framing, and DS1 performance monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SONOMASYSTEMS-SONOMA-ATM-T1-MIB?

This is a vendor-specific MIB from Sonoma Systems for managing ATM interfaces carried over T1 (DS1) circuits. It would expose T1 framing configuration and DS1 physical-layer performance data alongside ATM cell-layer parameters for the interface. Its monitoring emphasis is on physical-layer fault and performance status — DS1 line errors, framing alarms, and signal state — reflecting the health of the underlying T1 transport hardware rather than general system-level resources. It would depend on standard DS1/ATM MIBs (e.g., RFC 2495 DS1/E1 MIB, ATM-MIB) for shared conventions typical of T1-over-ATM interface modules. It was deployed on Sonoma Systems ATM access equipment providing T1 uplinks, typically in carrier access or enterprise WAN settings. Engineers can download the SONOMASYSTEMS-SONOMA-ATM-T1-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SONOMASYSTEMS-SONOMA-ATM-T1-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Sonoma Systems ATM T1 access device

Monitoring Examples

No sample objects were provided for this module, so a concrete example cannot be built from real object names; based on the description an admin would poll DS1 framing/alarm status and ATM cell counters on the T1 interface to detect line degradation.

What Can Be Monitored

DS1/T1 framing and alarm status
ATM cell-layer counters
interface line state

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter

From SONOMASYSTEMS-SONOMA-MIB

sonomaATM

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
sonomaT1ATMAdapterGroup	1.3.6.1.4.1.2926.25.7.5
atmDs1ConfGroup	1.3.6.1.4.1.2926.25.7.5.1
atmDs1ConfPhyTable	1.3.6.1.4.1.2926.25.7.5.1.1		not-accessible	A table of physical layer configuration for the DS1 interface
atmDs1ConfPhyEntry	1.3.6.1.4.1.2926.25.7.5.1.1.1		not-accessible	A entry in the table, containing information about the physical layer of a DS1 interface
INT atmDs1ConfPhysIndex	1.3.6.1.4.1.2926.25.7.5.1.1.1.1	INTEGER	read-only	The physical interface index.
INT atmDs1ConfLoopback	1.3.6.1.4.1.2926.25.7.5.1.1.1.2	INTEGER	read-write	This object is used to modify the state of internal loopback....
INT atmDs1ConfTxClockSelect	1.3.6.1.4.1.2926.25.7.5.1.1.1.3	INTEGER	read-write	Configure the transmit clock.
INT atmDs1ConfFillerCells	1.3.6.1.4.1.2926.25.7.5.1.1.1.4	INTEGER	read-write	This parameter indicates the type of filler cells to send when there are no data cells.
INT atmDs1ConfLineBuildOut	1.3.6.1.4.1.2926.25.7.5.1.1.1.5	INTEGER	read-write	This parameter indicates the value selected for the Line Build Out.
atmDs1StatsGroup	1.3.6.1.4.1.2926.25.7.5.2
atmDs1StatsTable	1.3.6.1.4.1.2926.25.7.5.2.1		not-accessible	A table of physical layer statistics information for the DS1 interface
atmDs1StatsEntry	1.3.6.1.4.1.2926.25.7.5.2.1.1		not-accessible	A entry in the table, containing information about the physical layer of a DS1 interface
INT atmDs1StatsPhysIndex	1.3.6.1.4.1.2926.25.7.5.2.1.1.1	INTEGER	read-only	The physical interface index.
CTR atmDs1StatsNoSignals	1.3.6.1.4.1.2926.25.7.5.2.1.1.2	Counter	read-only	No signal error counter.
CTR atmDs1StatsAISDetects	1.3.6.1.4.1.2926.25.7.5.2.1.1.3	Counter	read-only	AIS Detect counter.
CTR atmDs1StatsYelAlarmCount	1.3.6.1.4.1.2926.25.7.5.2.1.1.4	Counter	read-only	A count of the number of Yellow Alarms.
CTR atmDs1StatsLCVErrors	1.3.6.1.4.1.2926.25.7.5.2.1.1.5	Counter	read-only	LCV (Line Code Violation) error counter.
CTR atmDs1StatsPCVErrors	1.3.6.1.4.1.2926.25.7.5.2.1.1.6	Counter	read-only	PCV (Path Code Violation) error counter.
CTR atmDs1StatsMOSErrors	1.3.6.1.4.1.2926.25.7.5.2.1.1.7	Counter	read-only	Multiframe out of sync error counter.
CTR atmDs1StatsSyncLossCount	1.3.6.1.4.1.2926.25.7.5.2.1.1.8	Counter	read-only	Sync Loss counter.
CTR atmDs1StatsHECErrors	1.3.6.1.4.1.2926.25.7.5.2.1.1.9	Counter	read-only	HEC error counter.
INT atmDs1StatsSignalLoss	1.3.6.1.4.1.2926.25.7.5.2.1.1.10	INTEGER	read-only	Signal loss indication.
INT atmDs1StatsAISDetect	1.3.6.1.4.1.2926.25.7.5.2.1.1.11	INTEGER	read-only	AIS indication.
INT atmDs1StatsYellowAlarm	1.3.6.1.4.1.2926.25.7.5.2.1.1.12	INTEGER	read-only	Yellow Alarm indication.
INT atmDs1StatsSyncLoss	1.3.6.1.4.1.2926.25.7.5.2.1.1.13	INTEGER	read-only	Loss of sync indication.
INT atmDs1StatsTxClockLoss	1.3.6.1.4.1.2926.25.7.5.2.1.1.14	INTEGER	read-only	Loss of transmit clock indication.
INT atmDs1StatsClearCounters	1.3.6.1.4.1.2926.25.7.5.2.1.1.15	INTEGER	read-write	Clear all counters in this group ONLY.

RFC description

Manages Sonoma Systems ATM/DS1 T1 interface configuration and statistics including frame transmission metrics.

Start monitoring Sonoma Systems ATM T1 access device (DS1 physical-layer/ATM cell status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SONOMASYSTEMS-SONOMA-ATM-T1-MIB

What Is SONOMASYSTEMS-SONOMA-ATM-T1-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description