All MIBs › SLAPM-MIB
Organization: International Business Machines Corp.
Last Updated: 2000-01-24
Category: Network Monitoring (RMON), Quality of Service
Description: Defines managed objects for Service Level Agreement performance monitoring, tracking network QoS policy compliance with per-policy statistics.
IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring SLAPM-MIB with a free 30-day trial of IPNetwork Monitor.
What Is SLAPM-MIB?
SLAPM-MIB (Service Level Agreement Performance Monitoring MIB) is a vendor-neutral SNMP module used to track compliance with network Service Level Agreements (SLAs) and quality-of-service (QoS) policies. It exposes data organized around SLA policy definitions paired with per-policy performance statistics measured against configured thresholds. In monitoring terms it is oriented toward software/policy-level status rather than hardware health, letting an operator see whether SLA thresholds such as latency, jitter, or loss are being met on an ongoing basis. It commonly works alongside other performance and QoS-related MIBs (e.g., DiffServ or RMON) since it defines the SLA policy wrapper rather than the underlying metric-collection mechanism itself. It is typically deployed in service-provider or enterprise networks that need SLA compliance reporting to customers or management, where SLAPM-MIB SNMP monitoring provides the underlying policy-vs-threshold visibility for that reporting.
IPNetwork Monitor allows you to monitor SNMP objects defined in SLAPM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- vendor-neutral, standards-based MIB, not tied to a specific manufacturer
- SLA-aware routers/switches
- network performance monitoring probes
Monitoring Examples
An administrator would poll the SLA policy definition table and its paired statistics table to check whether a given policy's measured performance remains within its configured thresholds. No sample objects were extracted for this module, so exact table/object names cannot be confirmed, but the MIB conceptually organizes an SLA policy table alongside a corresponding per-policy statistics table. A sustained SLA-violation counter increment on a policy would indicate the network is failing to meet its committed service level for that SLA. This MIB is used primarily for SLA compliance reporting rather than direct device hardware monitoring.
What Can Be Monitored
- SLA policy compliance status
- per-policy performance statistics
- threshold violation counts
- SLA policy definitions
This MIB depends on
Related MIBs
Imported Objects
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 | |
| experimental |
From SNMPv2-TC
| DateAndTime | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TestAndIncr |
How to Use in IPNetwork Monitor
Example using slapmPolicyCountQueries OID:
Select a device implementing SLAPM-MIB as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type slapmPolicyCountQueries into the Find box to locate it in the OID tree, then select it and click OK. The total number of times that a policy lookup occurred with respect to a policy agent. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| slapmMIB | 1.3.6.1.3.88 | The Service Level Agreement Performance Monitoring MIB (SLAPM-MIB) provides data collection and monitoring capabilities for Service Level Agreements (SLAs) policy definitions. | ||
| slapmNotifications | 1.3.6.1.3.88.0 | |||
| NTF slapmMonitoredEventNotAchieved | 1.3.6.1.3.88.0.1 | This notification is generated when an monitored event is not achieved with respect to threshold. This applies only towards monitoring a policy traffic profile as an aggregate via an associating slapmPolicyStatsEntry. The value of slapmPolicyMonitorControl can be examined to determine what is being monitored. The first slapmPolicyMonitorStatus value supplies the current monitor status while the 2nd value supplies the previous status. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableAggregateTraps(3), MUST be selected in order for this notification to potentially be generated. | ||
| NTF slapmMonitoredEventOkay | 1.3.6.1.3.88.0.2 | This notification is generated when a monitored event has improved to an acceptable level. This applies only towards monitoring a policy traffic profile as an aggregate via an associating slapmPolicyStatsEntry. The value of slapmPolicyMonitorControl can be examined to determine what is being monitored. The first slapmPolicyMonitorStatus value supplies the current monitor status while the 2nd value supplies the previous status. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableAggregateTraps(3), MUST be selected in order for this notification to potentially be generated. | ||
| NTF slapmPolicyProfileDeleted | 1.3.6.1.3.88.0.3 | A slapmPolicyDeleted notification is sent when a slapmPolicyStatsEntry is deleted if the value of slapmPolicyTrapEnable is enabled(1). | ||
| NTF slapmPolicyMonitorDeleted | 1.3.6.1.3.88.0.4 | A slapmPolicyMonitorDeleted notification is sent when a slapmPolicyMonitorEntry is deleted if the value of slapmPolicyTrapEnable is enabled(1). | ||
| NTF slapmSubcomponentMonitoredEventNotAchieved | 1.3.6.1.3.88.0.5 | This notification is generated when a monitored value does not achieved a threshold specification. This applies only towards monitoring the individual components of a policy traffic profile. The value of the corresponding slapmPolicyMonitorControl can be examined to determine what is being monitored. The first slapmSubcomponentMonitorStatus value supplies the current monitor status while the 2nd value supplies the previous status. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableSubcomponentTraps(4), MUST be selected in order for this notification to potentially be generated. | ||
| NTF slapmSubcomponentMonitoredEventOkay | 1.3.6.1.3.88.0.6 | This notification is generated when a monitored value has reached an acceptable level. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableSubcomponentTraps(3), MUST be selected in order for this notification to potentially be generated. | ||
| NTF slapmPolicyRuleMonNotOkay | 1.3.6.1.3.88.0.7 | This notification is generated when an monitored event is not achieved with respect to a threshold. This applies only towards monitoring a policy rule as an aggregate via an associating slapmPolicyRuleStatsEntry. The value of slapmPRMonControl can be examined to determine what is being monitored. The first slapmPRMonStatus value supplies the current monitor status while the 2nd value supplies the previous status. Note: The corresponding slapmPRMonControl BITS setting, enableAggregateTraps(3), MUST be selected in order for this notification to potentially be generated. | ||
| NTF slapmPolicyRuleMonOkay | 1.3.6.1.3.88.0.8 | This notification is generated when a monitored event has improved to an acceptable level. This applies only towards monitoring a policy rule as an aggregate via an associating slapmPolicyRuleStatsEntry. The value of slapmPRMonControl can be examined to determine what is being monitored. The first slapmPRMonStatus value supplies the current monitor status while the 2nd value supplies the previous status. Note: The corresponding slapmPRMonControl BITS setting, enableAggregateTraps(3), MUST be selected in order for this notification to potentially be generated. | ||
| NTF slapmPolicyRuleDeleted | 1.3.6.1.3.88.0.9 | A slapmPolicyRuleDeleted notification is sent when a slapmPolicyRuleStatsEntry is deleted if the value of slapmPolicyTrapEnable is enabled(1). | ||
| NTF slapmPolicyRuleMonDeleted | 1.3.6.1.3.88.0.10 | A slapmPolicyRuleMonDeleted notification is sent when a slapmPRMonEntry is deleted if the value of slapmPolicyTrapEnable is enabled(1). | ||
| NTF slapmSubcMonitorNotOkay | 1.3.6.1.3.88.0.11 | This notification is generated when a monitored value does not achieved a threshold specification. This applies only towards monitoring the individual components of a policy rule. The value of the corresponding slapmPRMonControl can be examined to determine what is being monitored. The first slapmSubcomponentMonitorStatus value supplies the current monitor status while the 2nd value supplies the previous status. Note: The corresponding slapmPRMonControl BITS setting, enableSubcomponentTraps(4), MUST be selected in order for this notification to potentially be generated. | ||
| NTF slapmSubcMonitorOkay | 1.3.6.1.3.88.0.12 | This notification is generated when a monitored value has reached an acceptable level. Note: The corresponding slapmPRMonControl BITS setting, enableSubcomponentTraps(3), MUST be selected in order for this notification to potentially be generated. | ||
| slapmObjects | 1.3.6.1.3.88.1 | |||
| slapmBaseObjects | 1.3.6.1.3.88.1.1 | |||
| TES slapmSpinLock | 1.3.6.1.3.88.1.1.1 | TestAndIncr | read-write | An advisory lock used to allow cooperating applications to coordinate their use of the contents of this MIB. This typically occurs when an application seeks to create an new entry or alter an existing entry in slapmPRMonTable (or old slapmPolicyMonitorTable). A management implementation MAY utilize the slapmSpinLock to serialize its changes or additions. This usage is not required. However, slapmSpinLock MUST be supported by agent implementations. |
| C32 slapmPolicyCountQueriesEx | 1.3.6.1.3.88.1.1.2 | Counter32 | read-only | The total number of times that a policy lookup occurred with respect to a policy agent. This is the number of times that a reference was made to a policy definition at a system and includes the number of times that a policy repository was accessed, slapmPolicyCountAccesses. The object slapmPolicyCountAccesses should be less than slapmPolicyCountQueries when policy definitions are cached at a system. |
| C32 slapmPolicyCountAccesses | 1.3.6.1.3.88.1.1.3 | Counter32 | read-only | Total number of times that a policy repository was accessed with respect to a policy agent. The value of this object should be less than slapmPolicyCountQueries, since typically policy entries are cached to minimize repository accesses. |
| C32 slapmPolicyCountSuccessAccesses | 1.3.6.1.3.88.1.1.4 | Counter32 | read-only | Total number of successful policy repository accesses with respect to a policy agent. |
| C32 slapmPolicyCountNotFounds | 1.3.6.1.3.88.1.1.5 | Counter32 | read-only | Total number of policy repository accesses, with respect to a policy agent, that resulted in an entry not being located. |
| I32 slapmPolicyPurgeTime | 1.3.6.1.3.88.1.1.6 | Integer32 | read-write | The purpose of this object is to define the amount of time (in seconds) to wait before removing an slapmPolicyRuleStatsEntry (or old slapmPolicyStatsEntry) when a system detects that the associated policy definition has been deleted. This gives any polling management applications time to complete their last poll before an entry is removed. An slapmPolicyRuleStatsEntry (or old slapmPolicyStatsEntry) enters the deleteNeeded(3) state via slapmPolicyRuleStatsOperStatus (or old slapmPolicyStatsOperStatus) when a system first detects that the entry needs to be removed. Once slapmPolicyPurgeTime has expired for an entry in deleteNeeded(3) state it is removed a long with any dependent slapmPRMonTable (or slapmPolicyMonitorTable) entries. A value of 0 for this option disables this function and results in the automatic purging of slapmPRMonTable (or slapmPolicyTable) entries upon transition into deleteNeeded(3) state. A slapmPolicyRuleDeleted (or slapmPolicyProfileDeleted) notification is sent when an slapmPolicyRuleStatsEntry (or slapmPolicyStatsEntry) is removed. Dependent slapmPRMonTable (or slapmPolicyMonitorTable) deletion results in a slapmPolicyRuleMonDeleted (or slapmPolicyMonitorDeleted) notification being sent. These notifications are suppressed if the value of slapmPolicyTrapEnable is disabled(2). |
| INT slapmPolicyTrapEnable | 1.3.6.1.3.88.1.1.7 | INTEGER | read-write | Indicates whether slapmPolicyRuleDeleted and slapmPolicyRuleMonDeleted (or slapmPolicyProfileDeleted and slapmPolicyMonitorDeleted) notifications should be generated by this system. |
| I32 slapmPolicyTrapFilter | 1.3.6.1.3.88.1.1.8 | Integer32 | read-write | The purpose of this object is to suppress unnecessary slapmSubcMonitorNotOkay (or slapmSubcomponentMonitoredEventNotAchieved), for example, notifications. Basically, a monitored event has to not meet its SLA requirement for the number of consecutive intervals indicated by the value of this object. |
| slapmTableObjects | 1.3.6.1.3.88.1.2 | |||
| slapmPolicyStatsTable | 1.3.6.1.3.88.1.2.1 | not-accessible | Provides statistics on all policies known at a system. This table has been deprecated and replaced with the slapmPolicyRuleStatsTable. Older implementations of this MIB are expected to continue their support of this table. | |
| slapmPolicyStatsEntry | 1.3.6.1.3.88.1.2.1.1 | not-accessible | Defines an entry in the slapmPolicyStatsTable. This table defines a set of statistics that is kept on a per system, policy and traffic profile basis. A policy can be defined to contain multiple traffic profiles that map to a single action. Entries in this table are not created or deleted via SNMP but reflect the set of policy definitions known at a system. | |
| OCT slapmPolicyStatsSystemAddress | 1.3.6.1.3.88.1.2.1.1.1 | OCTET STRING | not-accessible | Address of a system that an Policy definition relates to. A zero length octet string must be used to indicate that only a single system is being represented. Otherwise, the length of the octet string must be 4 for an ipv4 address or 16 for an ipv6 address. |
| SLA slapmPolicyStatsPolicyName | 1.3.6.1.3.88.1.2.1.1.2 | SlapmNameType | not-accessible | Policy name that this entry relates to. |
| SLA slapmPolicyStatsTrafficProfileName | 1.3.6.1.3.88.1.2.1.1.3 | SlapmNameType | not-accessible | The name of a traffic profile that is associated with a policy. |
| INT slapmPolicyStatsOperStatus | 1.3.6.1.3.88.1.2.1.1.4 | INTEGER | read-only | The state of a policy entry: inactive(1) - An policy entry was either defined by local system definition or discovered via a directory search but has not been activated (not currently being used). active(2) - Policy entry is being used to affect traffic flows. deleteNeeded(3) - Either though local implementation dependent methods or by discovering that the directory entry corresponding to this table entry no longer exists and slapmPolicyPurgeTime needs to expire before attempting to remove the corresponding slapmPolicyStatsEntry and any dependent slapmPolicyMonitor table entries. Note: a policy traffic profile in a state other than active(1) is not being used to affect traffic flows. |
| G32 slapmPolicyStatsActiveConns | 1.3.6.1.3.88.1.2.1.1.5 | Gauge32 | read-only | The number of active TCP connections that are affected by the corresponding policy entry. |
| C32 slapmPolicyStatsTotalConns | 1.3.6.1.3.88.1.2.1.1.6 | Counter32 | read-only | The number of total TCP connections that are affected by the corresponding policy entry. |
| DAT slapmPolicyStatsFirstActivated | 1.3.6.1.3.88.1.2.1.1.7 | DateAndTime | read-only | The timestamp for when the corresponding policy entry is activated. The value of this object serves as the discontinuity event indicator when polling entries in this table. The value of this object is updated on transition of slapmPolicyStatsOperStatus into the active(2) state. |
| DAT slapmPolicyStatsLastMapping | 1.3.6.1.3.88.1.2.1.1.8 | DateAndTime | read-only | The timestamp for when the last time that the associated policy entry was used. |
| C32 slapmPolicyStatsInOctets | 1.3.6.1.3.88.1.2.1.1.9 | Counter32 | read-only | The number of octets that was received by IP for an entity that map to this entry. |
| C32 slapmPolicyStatsOutOctets | 1.3.6.1.3.88.1.2.1.1.10 | Counter32 | read-only | The number of octets that was transmitted by IP for an entity that map to this entry. |
| I32 slapmPolicyStatsConnectionLimit | 1.3.6.1.3.88.1.2.1.1.11 | Integer32 | read-only | The limit for the number of active TCP connections that are allowed for this policy definition. A value of zero for this object implies that a connection limit has not been specified. |
| C32 slapmPolicyStatsCountAccepts | 1.3.6.1.3.88.1.2.1.1.12 | Counter32 | read-only | This counter is incremented when a policy action's Permission value is set to Accept and a session (TCP connection) is accepted. |
| C32 slapmPolicyStatsCountDenies | 1.3.6.1.3.88.1.2.1.1.13 | Counter32 | read-only | This counter is incremented when a policy action's Permission value is set to Deny and a session is denied, or when a session (TCP connection) is rejected due to a policy's connection limit (slapmPolicyStatsConnectLimit) being reached. |
| C32 slapmPolicyStatsInDiscards | 1.3.6.1.3.88.1.2.1.1.14 | Counter32 | read-only | This counter counts the number of in octets discarded. This occurs when an error is detected. Examples of this are buffer overflow, checksum error, or bad packet format. |
| C32 slapmPolicyStatsOutDiscards | 1.3.6.1.3.88.1.2.1.1.15 | Counter32 | read-only | This counter counts the number of out octets discarded. Examples of this are buffer overflow, checksum error, or bad packet format. |
| C32 slapmPolicyStatsInPackets | 1.3.6.1.3.88.1.2.1.1.16 | Counter32 | read-only | This counter counts the number of in packets received that relate to this policy entry from IP. |
| C32 slapmPolicyStatsOutPackets | 1.3.6.1.3.88.1.2.1.1.17 | Counter32 | read-only | This counter counts the number of out packets sent by IP that relate to this policy entry. |
| C32 slapmPolicyStatsInProfileOctets | 1.3.6.1.3.88.1.2.1.1.18 | Counter32 | read-only | This counter counts the number of in octets that are determined to be within profile. |
| C32 slapmPolicyStatsOutProfileOctets | 1.3.6.1.3.88.1.2.1.1.19 | Counter32 | read-only | This counter counts the number of out octets that are determined to be within profile. |
| I32 slapmPolicyStatsMinRate | 1.3.6.1.3.88.1.2.1.1.20 | Integer32 | read-only | The minimum transfer rate defined for this entry. |
| I32 slapmPolicyStatsMaxRate | 1.3.6.1.3.88.1.2.1.1.21 | Integer32 | read-only | The maximum transfer rate defined for this entry. |
| I32 slapmPolicyStatsMaxDelay | 1.3.6.1.3.88.1.2.1.1.22 | Integer32 | read-only | The maximum delay defined for this entry. |
| slapmPolicyMonitorTable | 1.3.6.1.3.88.1.2.2 | not-accessible | Provides a method of monitoring policies and their effect at a system. This table has been deprecated and replaced with the slapmPRMonTable. Older implementations of this MIB are expected to continue their support of this table. | |
| slapmPolicyMonitorEntry | 1.3.6.1.3.88.1.2.2.1 | not-accessible | Defines an entry in the slapmPolicyMonitorTable. This table defines which policies should be monitored on a per policy traffic profile basis. | |
| STR slapmPolicyMonitorOwnerIndex | 1.3.6.1.3.88.1.2.2.1.1 | SnmpAdminString | not-accessible | To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 2575, VACM) for tables in which multiple users may need to independently create or modify entries, the initial index is used as an 'owner index'. Such an initial index has a syntax of SnmpAdminString, and can thus be trivially mapped to a securityName or groupName as defined in VACM, in accordance with a security policy. All entries in that table belonging to a particular user will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the 'column' subidentifier) up to the end of the encoded owner index. To configure VACM to permit access to this portion of the table, one would create vacmViewTreeFamilyTable entries with the value of vacmViewTreeFamilySubtree including the owner index portion, and vacmViewTreeFamilyMask 'wildcarding' the column subidentifier. More elaborate configurations are possible. |
| OCT slapmPolicyMonitorSystemAddress | 1.3.6.1.3.88.1.2.2.1.2 | OCTET STRING | not-accessible | Address of a system that an Policy definition relates to. A zero length octet string can be used to indicate that only a single system is being represented. Otherwise, the length of the octet string should be 4 for an ipv4 address and 16 for an ipv6 address. |
| SLA slapmPolicyMonitorPolicyName | 1.3.6.1.3.88.1.2.2.1.3 | SlapmNameType | not-accessible | Policy name that this entry relates to. |
| SLA slapmPolicyMonitorTrafficProfileName | 1.3.6.1.3.88.1.2.2.1.4 | SlapmNameType | not-accessible | The corresponding Traffic Profile name. |
| BIT slapmPolicyMonitorControl | 1.3.6.1.3.88.1.2.2.1.5 | Bits | read-create | The value of this object determines the type and level of monitoring that is applied to a policy/profile. The value of this object can't be changed once the table entry that it is a part of is activated via a slapmPolicyMonitorRowStatus transition to active state. monitorMinRate(0) - Monitor minimum transfer rate. monitorMaxRate(1) - Monitor maximum transfer rate. monitorMaxDelay(2) - Monitor maximum delay. enableAggregateTraps(3) - The enableAggregateTraps(3) BITS setting enables notification generation when monitoring a policy traffic profile as an aggregate using the values in the corresponding slapmPolicyStatsEntry. By default this function is not enabled. enableSubcomponentTraps(4) - This BITS setting enables notification generation when monitoring all subcomponents that are mapped to an corresponding slapmPolicyStatsEntry. By default this function is not enabled. monitorSubcomponents(5) - This BITS setting enables monitoring of each subcomponent (typically a TCP connection or UDP listener) individually. |
| SLA slapmPolicyMonitorStatus | 1.3.6.1.3.88.1.2.2.1.6 | SlapmStatus | read-only | The value of this object indicates when a monitored value has not meet a threshold or isn't meeting the defined service level. The SlapmStatus TEXTUAL-CONVENTION defines two levels of not meeting a threshold. The first set: slaMinInRateNotAchieved(0), slaMaxInRateExceeded(1), slaMaxDelayExceeded(2), slaMinOutRateNotAchieved(3), slaMaxOutRateExceeded(4) are used to indicate when the SLA as an aggregate is not meeting a threshold while the second set: monitorMinInRateNotAchieved(5), monitorMaxInRateExceeded(6), monitorMaxDelayExceeded(7), monitorMinOutRateNotAchieved(8), monitorMaxOutRateExceeded(9) indicate that at least one subcomponent is not meeting a threshold. |
| I32 slapmPolicyMonitorInterval | 1.3.6.1.3.88.1.2.2.1.7 | Integer32 | read-create | The number of seconds that defines the sample period. |
| DAT slapmPolicyMonitorIntTime | 1.3.6.1.3.88.1.2.2.1.8 | DateAndTime | read-only | The timestamp for when the last interval ended. |
| G32 slapmPolicyMonitorCurrentInRate | 1.3.6.1.3.88.1.2.2.1.9 | Gauge32 | read-only | Using the value of the corresponding slapmPolicyMonitorInterval, slapmPolicyStatsInOctets is sampled and then divided by slapmPolicyMonitorInterval to determine the current in transfer rate. |
| G32 slapmPolicyMonitorCurrentOutRate | 1.3.6.1.3.88.1.2.2.1.10 | Gauge32 | read-only | Using the value of the corresponding slapmPolicyMonitorInterval, slapmPolicyStatsOutOctets is sampled and then divided by slapmPolicyMonitorInterval to determine the current out transfer rate. |
| I32 slapmPolicyMonitorMinRateLow | 1.3.6.1.3.88.1.2.2.1.11 | Integer32 | read-create | The threshold for generating a slapmMonitoredEventNotAchieved notification, signalling that a monitored minimum transfer rate has not been meet. A slapmMonitoredEventNotAchieved notification is not generated again for an slapmPolicyMonitorEntry until the minimum transfer rate exceeds slapmPolicyMonitorMinRateHigh (a slapmMonitoredEventOkay notification is then transmitted) and then fails below slapmPolicyMonitorMinRateLow. This behavior reduces the slapmMonitoredEventNotAchieved notifications that are transmitted. A value of zero for this object is returned when the slapmPolicyMonitorControl monitorMinRate(0) is not enabled. When enabled the default value for this object is the min rate value specified in the associated action definition minus 10%. If the action definition doesn't have a min rate defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMinRate(0) is selected. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| I32 slapmPolicyMonitorMinRateHigh | 1.3.6.1.3.88.1.2.2.1.12 | Integer32 | read-create | The threshold for generating a slapmMonitoredEventOkay notification, signalling that a monitored minimum transfer rate has increased to an acceptable level. A value of zero for this object is returned when the slapmPolicyMonitorControl monitorMinRate(0) is not enabled. When enabled the default value for this object is the min rate value specified in the associated action definition plus 10%. If the action definition doesn't have a min rate defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMinRate(0) is selected. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| I32 slapmPolicyMonitorMaxRateHigh | 1.3.6.1.3.88.1.2.2.1.13 | Integer32 | read-create | The threshold for generating a slapmMonitoredEventNotAchieved notification, signalling that a monitored maximum transfer rate has been exceeded. A slapmMonitoredEventNotAchieved notification is not generated again for an slapmPolicyMonitorEntry until the maximum transfer rate fails below slapmPolicyMonitorMaxRateLow (a slapmMonitoredEventOkay notification is then transmitted) and then raises above slapmPolicyMonitorMaxRateHigh. This behavior reduces the slapmMonitoredEventNotAchieved notifications that are transmitted. A value of zero for this object is returned when the slapmPolicyMonitorControl monitorMaxRate(1) is not enabled. When enabled the default value for this object is the max rate value specified in the associated action definition plus 10%. If the action definition doesn't have a max rate defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMaxRate(1) is selected. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| I32 slapmPolicyMonitorMaxRateLow | 1.3.6.1.3.88.1.2.2.1.14 | Integer32 | read-create | The threshold for generating a slapmMonitoredEventOkay notification, signalling that a monitored maximum transfer rate has fallen to an acceptable level. A value of zero for this object is returned when the slapmPolicyMonitorControl monitorMaxRate(1) is not enabled. When enabled the default value for this object is the max rate value specified in the associated action definition minus 10%. If the action definition doesn't have a max rate defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMaxRate(1) is selected. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| I32 slapmPolicyMonitorMaxDelayHigh | 1.3.6.1.3.88.1.2.2.1.15 | Integer32 | read-create | The threshold for generating a slapmMonitoredEventNotAchieved notification, signalling that a monitored maximum delay rate has been exceeded. A slapmMonitoredEventNotAchieved notification is not generated again for an slapmPolicyMonitorEntry until the maximum delay rate falls below slapmPolicyMonitorMaxDelayLow (a slapmMonitoredEventOkay notification is then transmitted) and raises above slapmPolicyMonitorMaxDelayHigh. This behavior reduces the slapmMonitoredEventNotAchieved notifications that are transmitted. A value of zero for this object is returned when the slapmPolicyMonitorControl monitorMaxDelay(4) is not enabled. When enabled the default value for this object is the max delay value specified in the associated action definition plus 10%. If the action definition doesn't have a max delay defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMaxDelay(4) is selected. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| I32 slapmPolicyMonitorMaxDelayLow | 1.3.6.1.3.88.1.2.2.1.16 | Integer32 | read-create | The threshold for generating a slapmMonitoredEventOkay notification, signalling that a monitored maximum delay rate has fallen to an acceptable level. A value of zero for this object is returned when the slapmPolicyMonitorControl monitorMaxDelay(4) is not enabled. When enabled the default value for this object is the max delay value specified in the associated action definition minus 10%. If the action definition doesn't have a max delay defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMaxDelay(4) is selected. Note: The corresponding slapmPolicyMonitorControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| C32 slapmPolicyMonitorMinInRateNotAchieves | 1.3.6.1.3.88.1.2.2.1.17 | Counter32 | read-only | The number of times that a minimum transfer in rate was not achieved. |
| C32 slapmPolicyMonitorMaxInRateExceeds | 1.3.6.1.3.88.1.2.2.1.18 | Counter32 | read-only | The number of times that a maximum transfer in rate was exceeded. |
| C32 slapmPolicyMonitorMaxDelayExceeds | 1.3.6.1.3.88.1.2.2.1.19 | Counter32 | read-only | The number of times that a maximum delay in rate was exceeded. |
| C32 slapmPolicyMonitorMinOutRateNotAchieves | 1.3.6.1.3.88.1.2.2.1.20 | Counter32 | read-only | The number of times that a minimum transfer out rate was not achieved. |
| C32 slapmPolicyMonitorMaxOutRateExceeds | 1.3.6.1.3.88.1.2.2.1.21 | Counter32 | read-only | The number of times that a maximum transfer out rate was exceeded. |
| G32 slapmPolicyMonitorCurrentDelayRate | 1.3.6.1.3.88.1.2.2.1.22 | Gauge32 | read-only | The current delay rate for this entry. This is calculated by taking the average of the TCP round trip times for all associating slapmSubcomponentTable entries within a interval. |
| ROW slapmPolicyMonitorRowStatus | 1.3.6.1.3.88.1.2.2.1.23 | RowStatus | read-create | This object allows entries to be created and deleted in the slapmPolicyMonitorTable. An entry in this table is deleted by setting this object to destroy(6). Removal of a corresponding (same policy and traffic profile names) slapmPolicyStatsEntry has the side effect of the automatic deletion an entry in this table. |
| slapmSubcomponentTable | 1.3.6.1.3.88.1.2.3 | not-accessible | Defines a table to provide information on the individually components that are mapped to a policy rule (or old traffic profile). The indexing for this table is designed to support the use of an SNMP GET-NEXT operation using only the remote address and remote port as a way for a management station to retrieve the table entries relating to a particular client. | |
| slapmSubcomponentEntry | 1.3.6.1.3.88.1.2.3.1 | not-accessible | Describes a particular subcomponent entry. This table does not have an OwnerIndex as part of its indexing since this table's contents is intended to span multiple users. | |
| OCT slapmSubcomponentRemAddress | 1.3.6.1.3.88.1.2.3.1.1 | OCTET STRING | not-accessible | Indicate the remote address of a subcomponent. A remote address can be either an ipv4 address in which case 4 octets are required or as an ipv6 address that requires 16 octets. The value of this subidentifier is a zero length octet string when this entry relates to a UDP listener. |
| I32 slapmSubcomponentRemPort | 1.3.6.1.3.88.1.2.3.1.2 | Integer32 | not-accessible | Indicate the remote port of a subcomponent. The value of this subidentifier is 0 when this entry relates to a UDP listener. |
| OCT slapmSubcomponentLocalAddress | 1.3.6.1.3.88.1.2.3.1.3 | OCTET STRING | not-accessible | Indicate the local address of a subcomponent. A local address can be either an ipv4 address in which case 4 octets are required or as an ipv6 address that requires 16 octets. |
| I32 slapmSubcomponentLocalPort | 1.3.6.1.3.88.1.2.3.1.4 | Integer32 | not-accessible | Indicate the local port of a subcomponent. |
| INT slapmSubcomponentProtocol | 1.3.6.1.3.88.1.2.3.1.5 | INTEGER | read-only | Indicate the protocol in use that identifies the type of subcomponent. |
| OCT slapmSubcomponentSystemAddress | 1.3.6.1.3.88.1.2.3.1.6 | OCTET STRING | read-only | Address of a system that an Policy definition relates to. A zero length octet string can be used to indicate that only a single system is being represented. Otherwise, the length of the octet string should be 4 for an ipv4 address and 16 for an ipv6 address. |
| SLA slapmSubcomponentPolicyName | 1.3.6.1.3.88.1.2.3.1.7 | SlapmNameType | read-only | Policy name that this entry relates to. This object, along with slapmSubcomponentTrafficProfileName, have been replaced with the use of an unsigned integer index that is mapped to an slapmPolicyNameEntry to actually identify policy naming. |
| SLA slapmSubcomponentTrafficProfileName | 1.3.6.1.3.88.1.2.3.1.8 | SlapmNameType | read-only | The corresponding traffic profile name. This object, along with slapmSubcomponentProfileName, have been replaced with the use of an unsigned integer index that is mapped to an slapmPolicyNameEntry to actually identify policy naming. |
| DAT slapmSubcomponentLastActivity | 1.3.6.1.3.88.1.2.3.1.9 | DateAndTime | read-only | The date and timestamp of when this entry was last used. |
| C32 slapmSubcomponentInOctets | 1.3.6.1.3.88.1.2.3.1.10 | Counter32 | read-only | The number of octets received from IP for this connection. |
| C32 slapmSubcomponentOutOctets | 1.3.6.1.3.88.1.2.3.1.11 | Counter32 | read-only | The number of octets sent to IP for this connection. |
| C32 slapmSubcomponentTcpOutBufferedOctets | 1.3.6.1.3.88.1.2.3.1.12 | Counter32 | read-only | Number of outgoing octets buffered. The value of this object is zero when the entry is not for a TCP connection. |
| C32 slapmSubcomponentTcpInBufferedOctets | 1.3.6.1.3.88.1.2.3.1.13 | Counter32 | read-only | Number of incoming octets buffered. The value of this object is zero when the entry is not for a TCP connection. |
| C32 slapmSubcomponentTcpReXmts | 1.3.6.1.3.88.1.2.3.1.14 | Counter32 | read-only | Number of retransmissions. The value of this object is zero when the entry is not for a TCP connection. |
| I32 slapmSubcomponentTcpRoundTripTime | 1.3.6.1.3.88.1.2.3.1.15 | Integer32 | read-only | The amount of time that has elapsed, measured in milliseconds, from when the last TCP segment was transmitted by the TCP Stack until the ACK was received. The value of this object is zero when the entry is not for a TCP connection. |
| I32 slapmSubcomponentTcpRoundTripVariance | 1.3.6.1.3.88.1.2.3.1.16 | Integer32 | read-only | Round trip time variance. The value of this object is zero when the entry is not for a TCP connection. |
| C32 slapmSubcomponentInPdus | 1.3.6.1.3.88.1.2.3.1.17 | Counter32 | read-only | The number of protocol related data units transferred inbound: slapmSubcomponentProtocol PDU Type udpListener(1) UDP datagrams tcpConnection(2) TCP segments |
| C32 slapmSubcomponentOutPdus | 1.3.6.1.3.88.1.2.3.1.18 | Counter32 | read-only | The number of protocol related data units transferred outbound: slapmSubcomponentProtocol PDU Type udpListener(1) UDP datagrams tcpConnection(2) TCP segments |
| STR slapmSubcomponentApplName | 1.3.6.1.3.88.1.2.3.1.19 | SnmpAdminString | read-only | The application name associated with this entry if known, otherwise a zero-length octet string is returned as the value of this object. |
| SLA slapmSubcomponentMonitorStatus | 1.3.6.1.3.88.1.2.3.1.20 | SlapmStatus | read-only | The value of this object indicates when a monitored value has exceeded a threshold or isn't meeting the defined service level. Only the following SlapmStatus BITS setting can be reported here: monitorMinInRateNotAchieved(5), monitorMaxInRateExceeded(6), monitorMaxDelayExceeded(7), monitorMinOutRateNotAchieved(8), monitorMaxOutRateExceeded(9) This object only has meaning when an corresponding slapmPolicyMonitorEntry exists with the slapmPolicyMonitorControl BITS setting monitorSubcomponents(5) enabled. |
| DAT slapmSubcomponentMonitorIntTime | 1.3.6.1.3.88.1.2.3.1.21 | DateAndTime | read-only | The timestamp for when the last interval ended. This object only has meaning when an corresponding slapmPRMonEntry (or old slapmPolicyMonitorEntry) exists with the slapmPRMonControl (or slapmPolicyMonitorControl) BITS setting monitorSubcomponents(5) enabled. All of the octets returned when monitoring is not in effect must be zero. |
| G32 slapmSubcomponentMonitorCurrentInRate | 1.3.6.1.3.88.1.2.3.1.22 | Gauge32 | read-only | Using the value of the corresponding slapmPRMonInterval (or slapmPolicyMonitorInterval), slapmSubcomponentStatsInOctets is divided by slapmSubcomponentMonitorInterval to determine the current in transfer rate. This object only has meaning when an corresponding slapmPRMonEntry (or slapmPolicyMonitorEntry) exists with the slapmPRMonControl (or slapmPolicyMonitorControl) BITS setting monitorSubcomponents(5) enabled. The value of this object is zero when monitoring is not in effect. |
| G32 slapmSubcomponentMonitorCurrentOutRate | 1.3.6.1.3.88.1.2.3.1.23 | Gauge32 | read-only | Using the value of the corresponding slapmPRMonInterval (or slapmPolicyMonitorInterva)l, slapmSubcomponentStatsOutOctets is divided by slapmPRMonInterval (or slapmPolicyMonitorInterval) to determine the current out transfer rate. This object only has meaning when an corresponding slapmPRMonEntry (or slapmPolicyMonitorEntry) exists with the slapmPRMonControl (or slapmPolicyMonitorControl) BITS setting monitorSubcomponents(5) enabled. The value of this object is zero when monitoring is not in effect. |
| U32 slapmSubcomponentPolicyRuleIndex | 1.3.6.1.3.88.1.2.3.1.24 | Unsigned32 | read-only | Points to an slapmPolicyNameEntry when combined with slapmSubcomponentSystemAddress to indicate the policy naming that relates to this entry. A value of 0 for this object MUST be returned when the corresponding slapmSubcomponentEntry has no policy rule associated with it. |
| slapmPolicyNameTable | 1.3.6.1.3.88.1.2.4 | not-accessible | Provides the mapping between a policy index as a unsigned 32 bit integer and the unique name associated with a policy rule. | |
| slapmPolicyNameEntry | 1.3.6.1.3.88.1.2.4.1 | not-accessible | Defines an entry in the slapmPolicyNameTable. | |
| OCT slapmPolicyNameSystemAddress | 1.3.6.1.3.88.1.2.4.1.1 | OCTET STRING | not-accessible | Address of a system that an Policy rule definition relates to. A zero length octet string must be used to indicate that only a single system is being represented. Otherwise, the length of the octet string must be 4 for an ipv4 address or 16 for an ipv6 address. |
| U32 slapmPolicyNameIndex | 1.3.6.1.3.88.1.2.4.1.2 | Unsigned32 | not-accessible | A locally arbitrary, but unique identifier associated with this table entry. This value is not expected to remain constant across reIPLs. |
| SLA slapmPolicyNameOfRule | 1.3.6.1.3.88.1.2.4.1.3 | SlapmPolicyRuleName | read-only | The unique name that identifies a policy rule definition. |
| slapmPolicyRuleStatsTable | 1.3.6.1.3.88.1.2.5 | not-accessible | Provides statistics on a per system and a per policy rule basis. | |
| slapmPolicyRuleStatsEntry | 1.3.6.1.3.88.1.2.5.1 | not-accessible | Defines an entry in the slapmPolicyRuleStatsTable. This table defines a set of statistics that is kept on a per system and per policy rule basis. Entries in this table are not created or deleted via SNMP but reflect the set of policy rule definitions known at a system. | |
| INT slapmPolicyRuleStatsOperStatus | 1.3.6.1.3.88.1.2.5.1.1 | INTEGER | read-only | The state of a policy entry: inactive(1) - An policy entry was either defined by local system definition or discovered via a directory search but has not been activated (not currently being used). active(2) - Policy entry is being used to affect traffic flows. deleteNeeded(3) - Either though local implementation dependent methods or by discovering that the directory entry corresponding to this table entry no longer exists and slapmPolicyPurgeTime needs to expire before attempting to remove the corresponding slapmPolicyStatsEntry and any dependent slapmPolicyMonitor table entries. Note: a policy rule in a state other than active(2) is not being used to affect traffic flows. |
| G32 slapmPolicyRuleStatsActiveConns | 1.3.6.1.3.88.1.2.5.1.2 | Gauge32 | read-only | The number of active TCP connections that are affected by the corresponding policy entry. |
| C32 slapmPolicyRuleStatsTotalConns | 1.3.6.1.3.88.1.2.5.1.3 | Counter32 | read-only | The number of total TCP connections that are affected by the corresponding policy entry. |
| DAT slapmPolicyRuleStatsLActivated | 1.3.6.1.3.88.1.2.5.1.4 | DateAndTime | read-only | The timestamp for when the corresponding policy entry was last activated. The value of this object serves as the discontinuity event indicator when polling entries in this table. The value of this object is updated on transition of slapmPolicyRuleStatsOperStatus into the active(2) state. |
| DAT slapmPolicyRuleStatsLastMapping | 1.3.6.1.3.88.1.2.5.1.5 | DateAndTime | read-only | The timestamp for when the last time that the associated policy entry was used. |
| C32 slapmPolicyRuleStatsInOctets | 1.3.6.1.3.88.1.2.5.1.6 | Counter32 | read-only | The number of octets that was received by IP for an entity that map to this entry. |
| C32 slapmPolicyRuleStatsOutOctets | 1.3.6.1.3.88.1.2.5.1.7 | Counter32 | read-only | The number of octets that was transmitted by IP for an entity that map to this entry. |
| U32 slapmPolicyRuleStatsConnLimit | 1.3.6.1.3.88.1.2.5.1.8 | Unsigned32 | read-only | The limit for the number of active TCP connections that are allowed for this policy definition. A value of zero for this object implies that a connection limit has not been specified. |
| C32 slapmPolicyRuleStatsCountAccepts | 1.3.6.1.3.88.1.2.5.1.9 | Counter32 | read-only | This counter is incremented when a policy action's Permission value is set to Accept and a session (TCP connection) is accepted. |
| C32 slapmPolicyRuleStatsCountDenies | 1.3.6.1.3.88.1.2.5.1.10 | Counter32 | read-only | This counter is incremented when a policy action's Permission value is set to Deny and a session is denied, or when a session (TCP connection) is rejected due to a policy's connection limit (slapmPolicyRuleStatsConnectLimit) being reached. |
| C32 slapmPolicyRuleStatsInDiscards | 1.3.6.1.3.88.1.2.5.1.11 | Counter32 | read-only | This counter counts the number of in octets discarded. This occurs when an error is detected. Examples of this are buffer overflow, checksum error, or bad packet format. |
| C32 slapmPolicyRuleStatsOutDiscards | 1.3.6.1.3.88.1.2.5.1.12 | Counter32 | read-only | This counter counts the number of out octets discarded. Examples of this are buffer overflow, checksum error, or bad packet format. |
| C32 slapmPolicyRuleStatsInPackets | 1.3.6.1.3.88.1.2.5.1.13 | Counter32 | read-only | This counter counts the number of in packets received that relate to this policy entry from IP. |
| C32 slapmPolicyRuleStatsOutPackets | 1.3.6.1.3.88.1.2.5.1.14 | Counter32 | read-only | This counter counts the number of out packets sent by IP that relate to this policy entry. |
| C32 slapmPolicyRuleStatsInProOctets | 1.3.6.1.3.88.1.2.5.1.15 | Counter32 | read-only | This counter counts the number of in octets that are determined to be within profile. |
| C32 slapmPolicyRuleStatsOutProOctets | 1.3.6.1.3.88.1.2.5.1.16 | Counter32 | read-only | This counter counts the number of out octets that are determined to be within profile. |
| U32 slapmPolicyRuleStatsMinRate | 1.3.6.1.3.88.1.2.5.1.17 | Unsigned32 | read-only | The minimum transfer rate defined for this entry. |
| U32 slapmPolicyRuleStatsMaxRate | 1.3.6.1.3.88.1.2.5.1.18 | Unsigned32 | read-only | The maximum transfer rate defined for this entry. |
| U32 slapmPolicyRuleStatsMaxDelay | 1.3.6.1.3.88.1.2.5.1.19 | Unsigned32 | read-only | The maximum delay defined for this entry. |
| C32 slapmPolicyRuleStatsTotalRsvpFlows | 1.3.6.1.3.88.1.2.5.1.20 | Counter32 | read-only | Total number of RSVP flows that have be activated. |
| G32 slapmPolicyRuleStatsActRsvpFlows | 1.3.6.1.3.88.1.2.5.1.21 | Gauge32 | read-only | Current number of active RSVP flows. |
| slapmPRMonTable | 1.3.6.1.3.88.1.2.6 | not-accessible | Provides a method of monitoring policies and their effect at a system. | |
| slapmPRMonEntry | 1.3.6.1.3.88.1.2.6.1 | not-accessible | Defines an entry in the slapmPRMonTable. This table defines which policies should be monitored on a per policy rule basis. An attempt to set any read-create object defined within an slapmPRMonEntry while the value of slapmPRMonRowStatus is active(1) will result in an inconsistentValue error. | |
| STR slapmPRMonOwnerIndex | 1.3.6.1.3.88.1.2.6.1.1 | SnmpAdminString | not-accessible | To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 2575, VACM) for tables in which multiple users may need to independently create or modify entries, the initial index is used as an 'owner index'. Such an initial index has a syntax of SnmpAdminString, and can thus be trivially mapped to a securityName or groupName as defined in VACM, in accordance with a security policy. All entries in that table belonging to a particular user will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the 'column' subidentifier) up to the end of the encoded owner index. To configure VACM to permit access to this portion of the table, one would create vacmViewTreeFamilyTable entries with the value of vacmViewTreeFamilySubtree including the owner index portion, and vacmViewTreeFamilyMask 'wildcarding' the column subidentifier. More elaborate configurations are possible. |
| OCT slapmPRMonSystemAddress | 1.3.6.1.3.88.1.2.6.1.2 | OCTET STRING | not-accessible | Address of a system that an Policy definition relates to. A zero length octet string can be used to indicate that only a single system is being represented. Otherwise, the length of the octet string should be 4 for an ipv4 address and 16 for an ipv6 address. |
| U32 slapmPRMonIndex | 1.3.6.1.3.88.1.2.6.1.3 | Unsigned32 | not-accessible | An slapmPolicyNameTable index, slapmPolicyNameIndex, that points to the unique name associated with a policy rule definition. |
| BIT slapmPRMonControl | 1.3.6.1.3.88.1.2.6.1.4 | Bits | read-create | The value of this object determines the type and level of monitoring that is applied to a policy rule. The value of this object can't be changed once the table entry that it is a part of is activated via a slapmPRMonRowStatus transition to active state. monitorMinRate(0) - Monitor minimum transfer rate. monitorMaxRate(1) - Monitor maximum transfer rate. monitorMaxDelay(2) - Monitor maximum delay. enableAggregateTraps(3) - The enableAggregateTraps(3) BITS setting enables notification generation when monitoring a policy rule as an aggregate using the values in the corresponding slapmPRMonStatsEntry. By default this function is not enabled. enableSubcomponentTraps(4) - This BITS setting enables notification generation when monitoring all subcomponents that are mapped to an corresponding slapmPRMonStatsEntry. By default this function is not enabled. monitorSubcomponents(5) - This BITS setting enables monitoring of each subcomponent (typically a TCP connection or UDP listener) individually. |
| SLA slapmPRMonStatus | 1.3.6.1.3.88.1.2.6.1.5 | SlapmStatus | read-only | The value of this object indicates when a monitored value has not meet a threshold or isn't meeting the defined service level. The SlapmStatus TEXTUAL-CONVENTION defines two levels of not meeting a threshold. The first set: slaMinInRateNotAchieved(0), slaMaxInRateExceeded(1), slaMaxDelayExceeded(2), slaMinOutRateNotAchieved(3), slaMaxOutRateExceeded(4) are used to indicate when the SLA as an aggregate is not meeting a threshold while the second set: monitorMinInRateNotAchieved(5), monitorMaxInRateExceeded(6), monitorMaxDelayExceeded(7), monitorMinOutRateNotAchieved(8), monitorMaxOutRateExceeded(9) indicate that at least one subcomponent is not meeting a threshold. |
| U32 slapmPRMonInterval | 1.3.6.1.3.88.1.2.6.1.6 | Unsigned32 | read-create | The number of seconds that defines the sample period. |
| DAT slapmPRMonIntTime | 1.3.6.1.3.88.1.2.6.1.7 | DateAndTime | read-only | The timestamp for when the last interval ended. |
| G32 slapmPRMonCurrentInRate | 1.3.6.1.3.88.1.2.6.1.8 | Gauge32 | read-only | Using the value of the corresponding slapmPRMonInterval, slapmPolicyRuleStatsInOctets is sampled and then divided by slapmPRMonInterval to determine the current in transfer rate. |
| G32 slapmPRMonCurrentOutRate | 1.3.6.1.3.88.1.2.6.1.9 | Gauge32 | read-only | Using the value of the corresponding slapmPolicyMonInterval, slapmPolicyRuleStatsOutOctets is sampled and then divided by slapmPRMonInterval to determine the current out transfer rate. |
| U32 slapmPRMonMinRateLow | 1.3.6.1.3.88.1.2.6.1.10 | Unsigned32 | read-create | The threshold for generating a slapmPolicyRuleMonNotOkay notification, signalling that a monitored minimum transfer rate has not been meet. A slapmPolicyRuleMonNotOkay notification is not generated again for an slapmPRMonEntry until the minimum transfer rate exceeds slapmPRMonMinRateHigh (a slapmPolicyRuleMonOkay notification is then transmitted) and then fails below slapmPRMonMinRateLow. This behavior reduces the slapmPolicyRuleMonNotOkay notifications that are transmitted. A value of zero for this object is returned when the slapmPRMonControl monitorMinRate(0) is not enabled. When enabled the default value for this object is the min rate value specified in the associated action definition minus 10%. If the action definition doesn't have a min rate defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMinRate(0) is selected. Note: The corresponding slapmPRMonControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| U32 slapmPRMonMinRateHigh | 1.3.6.1.3.88.1.2.6.1.11 | Unsigned32 | read-create | The threshold for generating a slapmPolicyRuleMonOkay notification, signalling that a monitored minimum transfer rate has increased to an acceptable level. A value of zero for this object is returned when the slapmPRMonControl monitorMinRate(0) is not enabled. When enabled the default value for this object is the min rate value specified in the associated action definition plus 10%. If the action definition doesn't have a min rate defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMinRate(0) is selected. Note: The corresponding slapmPRMonControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| U32 slapmPRMonMaxRateHigh | 1.3.6.1.3.88.1.2.6.1.12 | Unsigned32 | read-create | The threshold for generating a slapmPolicyRuleMonNotOkay notification, signalling that a monitored maximum transfer rate has been exceeded. A slapmPolicyRuleNotOkay notification is not generated again for an slapmPRMonEntry until the maximum transfer rate fails below slapmPRMonMaxRateLow (a slapmPolicyRuleMonOkay notification is then transmitted) and then raises above slapmPRMonMaxRateHigh. This behavior reduces the slapmPolicyRuleMonNotOkay notifications that are transmitted. A value of zero for this object is returned when the slapmPRMonControl monitorMaxRate(1) is not enabled. When enabled the default value for this object is the max rate value specified in the associated action definition plus 10%. If the action definition doesn't have a max rate defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMaxRate(1) is selected. Note: The corresponding slapmPRMonControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| U32 slapmPRMonMaxRateLow | 1.3.6.1.3.88.1.2.6.1.13 | Unsigned32 | read-create | The threshold for generating a slapmPolicyRuleMonOkay notification, signalling that a monitored maximum transfer rate has fallen to an acceptable level. A value of zero for this object is returned when the slapmPRMonControl monitorMaxRate(1) is not enabled. When enabled the default value for this object is the max rate value specified in the associated action definition minus 10%. If the action definition doesn't have a max rate defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMaxRate(1) is selected. Note: The corresponding slapmPRMonControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| U32 slapmPRMonMaxDelayHigh | 1.3.6.1.3.88.1.2.6.1.14 | Unsigned32 | read-create | The threshold for generating a slapmPolicyRuleMonNotOkay notification, signalling that a monitored maximum delay rate has been exceeded. A slapmPolicyRuleMonNotOkay notification is not generated again for an slapmPRMonEntry until the maximum delay rate falls below slapmPRMonMaxDelayLow (a slapmPolicyRuleMonOkay notification is then transmitted) and raises above slapmPRMonMaxDelayHigh. This behavior reduces the slapmPolicyRuleMonNotOkay notifications that are transmitted. A value of zero for this object is returned when the slapmPRMonControl monitorMaxDelay(4) is not enabled. When enabled the default value for this object is the max delay value specified in the associated action definition plus 10%. If the action definition doesn't have a max delay defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMaxDelay(4) is selected. Note: The corresponding slapmPRMonControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| U32 slapmPRMonMaxDelayLow | 1.3.6.1.3.88.1.2.6.1.15 | Unsigned32 | read-create | The threshold for generating a slapmPolicyRuleMonOkay notification, signalling that a monitored maximum delay rate has fallen to an acceptable level. A value of zero for this object is returned when the slapmPRMonControl monitorMaxDelay(4) is not enabled. When enabled the default value for this object is the max delay value specified in the associated action definition minus 10%. If the action definition doesn't have a max delay defined then there is no default for this object and a value MUST be specified prior to activating this entry when monitorMaxDelay(4) is selected. Note: The corresponding slapmPRMonControl BITS setting, enableAggregateTraps(3), MUST be selected in order for any notification relating to this entry to potentially be generated. |
| C32 slapmPRMonMinInRateNotAchieves | 1.3.6.1.3.88.1.2.6.1.16 | Counter32 | read-only | The number of times that a minimum transfer in rate was not achieved. |
| C32 slapmPRMonMaxInRateExceeds | 1.3.6.1.3.88.1.2.6.1.17 | Counter32 | read-only | The number of times that a maximum transfer in rate was exceeded. |
| C32 slapmPRMonMaxDelayExceeds | 1.3.6.1.3.88.1.2.6.1.18 | Counter32 | read-only | The number of times that a maximum delay in rate was exceeded. |
| C32 slapmPRMonMinOutRateNotAchieves | 1.3.6.1.3.88.1.2.6.1.19 | Counter32 | read-only | The number of times that a minimum transfer out rate was not achieved. |
| C32 slapmPRMonMaxOutRateExceeds | 1.3.6.1.3.88.1.2.6.1.20 | Counter32 | read-only | The number of times that a maximum transfer out rate was exceeded. |
| G32 slapmPRMonCurrentDelayRate | 1.3.6.1.3.88.1.2.6.1.21 | Gauge32 | read-only | The current delay rate for this entry. This is calculated by taking the average of the TCP round trip times for all associating slapmSubcomponentTable entries within a interval. |
| ROW slapmPRMonRowStatus | 1.3.6.1.3.88.1.2.6.1.22 | RowStatus | read-create | This object allows entries to be created and deleted in the slapmPRMonTable. An entry in this table is deleted by setting this object to destroy(6). Removal of an corresponding (same policy index) slapmPolicyRuleStatsEntry has the side effect of the automatic deletion an entry in this table. Note that an attempt to set any read-create object defined within an slapmPRMonEntry while the value of slapmPRMonRowStatus is active(1) will result in an inconsistentValue error. |
| slapmConformance | 1.3.6.1.3.88.2 | |||
| slapmCompliances | 1.3.6.1.3.88.2.1 | |||
| slapmCompliance | 1.3.6.1.3.88.2.1.1 | The compliance statement for the SLAPM-MIB. | ||
| slapmGroups | 1.3.6.1.3.88.2.2 | |||
| slapmBaseGroup | 1.3.6.1.3.88.2.2.1 | The group of objects defined by this MIB that are required for all implementations to be compliant. | ||
| slapmOptionalGroup | 1.3.6.1.3.88.2.2.2 | The group of objects defined by this MIB that are optional. | ||
| slapmEndSystemGroup | 1.3.6.1.3.88.2.2.3 | The group of objects defined by this MIB that are required for end system implementations. | ||
| slapmNotGroup | 1.3.6.1.3.88.2.2.4 | The group of notifications defined by this MIB that MUST be implemented. | ||
| slapmEndSystemNotGroup | 1.3.6.1.3.88.2.2.5 | The group of objects defined by this MIB that are required for end system implementations. | ||
| slapmBaseGroup2 | 1.3.6.1.3.88.2.2.6 | The group of objects defined by this MIB that are required for all implementations to be compliant. | ||
| slapmEndSystemGroup2 | 1.3.6.1.3.88.2.2.7 | The group of objects defined by this MIB that are required for end system implementations. | ||
| slapmNotGroup2 | 1.3.6.1.3.88.2.2.8 | The group of notifications defined by this MIB that MUST be implemented. | ||
| slapmEndSystemNotGroup2 | 1.3.6.1.3.88.2.2.9 | The group of objects defined by this MIB that are required for end system implementations. |
RFC description
Collects and monitors Service Level Agreement (SLA) performance metrics and policy rules.
Start monitoring vendor-neutral, standards-based MIB, SLA-aware routers/switches and performance monitoring probes (SLA policy vs. threshold status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.