All MIBs › SCSI-MIB
Organization: IETF
Last Updated: 2006-03-30
Category: Fibre Channel and Storage, Network Interfaces
Description: Manages Small Computer System Interface (SCSI) entities independent of the interconnect layer, covering SCSI instances, devices, ports, and logical units.
IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring SCSI-MIB with a free 30-day trial of IPNetwork Monitor.
What Is SCSI-MIB?
SCSI-MIB is an IETF standards-based module (RFC 4455) for managing Small Computer System Interface (SCSI) subsystems independent of the underlying transport or interconnect layer, applicable to storage controllers, HBAs, and SCSI target/initiator devices. It exposes data organized around SCSI instances, devices, ports, and logical units, covering identification, aliasing, and vendor/software version information for each SCSI entity. It is used to monitor the software status of SCSI stack instances (via scsiInstSoftwareIndex and scsiInstVendorVersion), track storage type classification, and detect fault conditions through SCSI notification objects, making it valuable for spotting misconfigured or failing SCSI adapters and storage paths. Because it is transport-independent, it is commonly layered alongside Fibre Channel or iSCSI MIBs that describe the underlying physical connection while SCSI-MIB describes the logical SCSI layer. It is typically deployed on storage servers, SAN host bus adapters, and RAID/storage array controllers where administrators need vendor-neutral visibility into SCSI-level health and identity. Engineers implementing or auditing this functionality typically reference the SCSI-MIB RFC/standard documentation for the authoritative specification.
IPNetwork Monitor allows you to monitor SNMP objects defined in SCSI-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- storage controller / HBA
- vendor-neutral, standards-based MIB, not tied to a specific manufacturer
- SAN/storage array
Monitoring Examples
An administrator would poll scsiInstanceTable (indexed by scsiInstIndex) to enumerate each SCSI protocol stack instance on a host, reading scsiInstAlias and scsiInstVendorVersion to confirm expected driver/firmware versions are running. Walking scsiDeviceTable/scsiDeviceEntry (scsiDeviceIndex, scsiDeviceAlias) reveals attached SCSI devices per instance; an unexpected drop in device count signals a disconnected drive or failed HBA port. Enabling scsiInstScsiNotificationsEnable lets the instance emit scsiNotifications traps when device state changes occur, so the admin is alerted rather than relying on polling alone.
What Can Be Monitored
- SCSI instance identity and alias
- SCSI driver/software version
- storage type classification
- attached SCSI device count
- SCSI-level notifications/traps
This MIB depends on
Related MIBs
Imported Objects
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 | |
| mib-2 |
From SNMPv2-TC
| AutonomousType | |
| RowPointer | |
| RowStatus | |
| StorageType | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using scsiPortBusyStatuses OID:
Select a device implementing SCSI-MIB as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type scsiPortBusyStatuses into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object represents the number of port busy statuses sent or received by this port. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| scsiAdmin | 1.3.6.1.2.1.139.1 | |||
| SCS scsiAttIntrPortAuthIntrIdx | 1.3.6.1.2.1.139.2.3.3.2.1.2 | ScsiIndexValueOrZero | read-only | This object is the corresponding index in the scsiAuthorizedIntrTable for this current attached remote SCSI initiator device or zero if this remote attached SCSI initiator device is not configured in that table. |
| scsiAttIntrPortEntry | 1.3.6.1.2.1.139.2.3.3.2.1 | not-accessible | An entry (row) represents a remote SCSI initiator port currently attached to a particular local SCSI target port of a particular SCSI target device of a particular SCSI instance. | |
| OID scsiAttIntrPortIdentifier | 1.3.6.1.2.1.139.2.3.3.2.1.4 | ScsiIdentifier | read-only | This object represents the identifier of the remote SCSI initiator device attached to this local SCSI target port. |
| SCS scsiAttIntrPortIndex | 1.3.6.1.2.1.139.2.3.3.2.1.1 | ScsiIndexValue | not-accessible | This object represents an arbitrary integer used to uniquely identify a particular attached remote initiator port to a particular SCSI target port within a particular SCSI target device within a particular SCSI instance. |
| SCS scsiAttIntrPortName | 1.3.6.1.2.1.139.2.3.3.2.1.3 | ScsiName | read-only | This object represents the name of the remote SCSI initiator device attached to this local SCSI target port. |
| scsiAttIntrPortTable | 1.3.6.1.2.1.139.2.3.3.2 | not-accessible | This table includes all the remote SCSI initiator ports that are currently attached to a local SCSI target port of all local devices within all SCSI instances. | |
| SCS scsiAttTgtPortDscTgtIdx | 1.3.6.1.2.1.139.2.2.3.4.1.2 | ScsiIndexValueOrZero | read-only | This object contains the value of the scsiDscTgtIntrPortIndex index variable for the row in the scsiDscTgtTable representing this currently attached SCSI target port. If the currently attached SCSI target port is not represented in the scsiDscTgtTable, then the value of this object is zero. |
| scsiAttTgtPortEntry | 1.3.6.1.2.1.139.2.2.3.4.1 | not-accessible | An entry (row) represents a remote SCSI target port (scsiAttTgtPortIndex) currently attached to a particular SCSI initiator port (scsiPortIndex) of a particular SCSI initiator device within a particular SCSI instance. | |
| OID scsiAttTgtPortIdentifier | 1.3.6.1.2.1.139.2.2.3.4.1.4 | ScsiIdentifier | read-only | This object contains the identifier of the attached SCSI target port. |
| SCS scsiAttTgtPortIndex | 1.3.6.1.2.1.139.2.2.3.4.1.1 | ScsiIndexValue | not-accessible | An arbitrary integer used to uniquely identify a particular SCSI target currently attached to a particular SCSI initiator port of a particular SCSI initiator device within a particular SCSI instance. |
| SCS scsiAttTgtPortName | 1.3.6.1.2.1.139.2.2.3.4.1.3 | ScsiName | read-only | This object contains the name of the attached SCSI target port. |
| scsiAttTgtPortTable | 1.3.6.1.2.1.139.2.2.3.4 | not-accessible | This table includes all the remote (not in the local system) SCSI target ports that are currently attached to each local SCSI initiator port of this SCSI instance. | |
| C32 scsiAuthIntrAttachedTimes | 1.3.6.1.2.1.139.2.3.3.1.1.6 | Counter32 | read-only | This object indicates the number of times that this remote SCSI initiator device or port has transitioned from unattached to attached to this local SCSI target device or port. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation. |
| SCS scsiAuthIntrDevOrPort | 1.3.6.1.2.1.139.2.3.3.1.1.3 | ScsiDeviceOrPort | read-create | This object specifies whether this entry refers to a remote SCSI initiator port or to a SCSI initiator device. A value of device(1) means that the authorized remote initiator is a SCSI initiator device and includes all of its ports. A value of port(2) means that the authorized remote initiator is a SCSI initiator port. |
| C64 scsiAuthIntrHSOutCommands | 1.3.6.1.2.1.139.2.3.3.1.1.10 | Counter64 | read-only | This object represents the number of commands sent by the remote SCSI initiator device or port corresponding to this entry to the local SCSI target device or port corresponding to this entry. This object provides support for systems that can quickly generate a large number of commands because they run at high speed. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation. |
| SCS scsiAuthIntrIndex | 1.3.6.1.2.1.139.2.3.3.1.1.2 | ScsiIndexValue | not-accessible | This object is an arbitrary integer used to uniquely identify a SCSI initiator device or port that is authorized to attach to a particular local SCSI target device or port of a particular SCSI instance. |
| TIM scsiAuthIntrLastCreation | 1.3.6.1.2.1.139.2.3.3.1.1.11 | TimeStamp | read-only | This object indicates the value of sysUpTime when this row was last created. |
| SCS scsiAuthIntrLunMapIndex | 1.3.6.1.2.1.139.2.3.3.1.1.5 | ScsiIndexValueOrZero | read-create | This object identifies the set of entries in the scsiLunMapTable for which scsiLunMapIndex has the same value as the value of this object. The identified set of entries constitutes the LUN map to be used for accessing logical units when the remote SCSI initiator port or device corresponding to this entry is attached to any local SCSI target port or device corresponding to this entry. Note that this object has a value of zero if this entry should use the default LUN map. |
| SCS scsiAuthIntrName | 1.3.6.1.2.1.139.2.3.3.1.1.4 | ScsiName | read-create | This object represents the name of the remote SCSI initiator device or port authorized by this row. |
| C32 scsiAuthIntrOutCommands | 1.3.6.1.2.1.139.2.3.3.1.1.7 | Counter32 | read-only | This object indicates the number of commands that the remote SCSI initiator device or port corresponding to this entry has sent to the local SCSI target device or port corresponding to this entry. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation. |
| C32 scsiAuthIntrReadMegaBytes | 1.3.6.1.2.1.139.2.3.3.1.1.8 | Counter32 | read-only | This object indicates the amount of data in megabytes that the remote SCSI initiator device or port corresponding to this entry has read from the local SCSI target device or port corresponding to this entry. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation. |
| ROW scsiAuthIntrRowStatus | 1.3.6.1.2.1.139.2.3.3.1.1.12 | RowStatus | read-create | This object allows an administrator to create or delete this entry. A newly created row cannot be made active until a value has been set for scsiAuthIntrName. In this case, the value of the corresponding instance of the scsiAuthIntrRowStatus column will stay 'notReady'. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| SCS scsiAuthIntrTgtPortIndex | 1.3.6.1.2.1.139.2.3.3.1.1.1 | ScsiPortIndexValueOrZero | not-accessible | This object contains either the index of the port or zero, to indicate any port, on the particular local SCSI target device. |
| C32 scsiAuthIntrWrittenMegaBytes | 1.3.6.1.2.1.139.2.3.3.1.1.9 | Counter32 | read-only | This object indicates the amount of data in megabytes that the remote SCSI initiator device or port corresponding to this entry has written to the local SCSI target device or port corresponding to this entry. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiAuthIntrLastCreation. |
| scsiAuthorizedIntrEntry | 1.3.6.1.2.1.139.2.3.3.1.1 | not-accessible | An entry (row) represents a remote SCSI initiator port or remote SCSI initiator device that may attach to the local SCSI target port or device within a particular SCSI instance. The StorageType of a row in this table is specified by the instance of scsiInstStorageType that is INDEXed by the same value of scsiInstIndex. | |
| scsiAuthorizedIntrTable | 1.3.6.1.2.1.139.2.3.3.1 | not-accessible | This table includes all the authorized SCSI initiator devices or ports that may attach a SCSI target device (ScsiAuthIntrTgtPortIndex = 0) or port (ScsiAuthIntrTgtPortIndex different than 0) of the local SCSI instance. Statistics are kept for each such authorization; thus, the authorizations should be configured in the manner that will cause the desired set of statistics to be collected and that will determine the correct LUN map. | |
| scsiCompliance | 1.3.6.1.2.1.139.3.1.1 | Describes the requirements for compliance to this SCSI MIB module. If an implementation can be both a SCSI target device and a SCSI initiator device, all groups are mandatory. | ||
| scsiCompliances | 1.3.6.1.2.1.139.3.1 | |||
| scsiConformance | 1.3.6.1.2.1.139.3 | |||
| STR scsiDeviceAlias | 1.3.6.1.2.1.139.2.1.2.1.2 | SnmpAdminString | read-write | This object contains an administrative name for this device. If no name is assigned, the value of this object is the zero-length string. The StorageType of this object is specified by the instance of scsiInstStorageType that is INDEXed by the same value of scsiInstIndex. |
| scsiDeviceEntry | 1.3.6.1.2.1.139.2.1.2.1 | not-accessible | An entry (row) containing management information applicable to a particular SCSI device included in this SCSI manageable instance identifiable by the value of scsiInstIndex. | |
| scsiDeviceGroup | 1.3.6.1.2.1.139.3.2.1 | A collection of objects providing information about SCSI instances, devices, and ports. | ||
| SCS scsiDeviceIndex | 1.3.6.1.2.1.139.2.1.2.1.1 | ScsiIndexValue | not-accessible | This object is an arbitrary integer used to uniquely identify a particular device within a particular SCSI instance. |
| U32 scsiDevicePortNumber | 1.3.6.1.2.1.139.2.1.2.1.4 | Unsigned32 | read-only | This object represents the number of ports contained in this device. |
| BIT scsiDeviceRole | 1.3.6.1.2.1.139.2.1.2.1.3 | Bits | read-only | This object determines whether this device is acting as a SCSI initiator device, or as a SCSI target device, or as both. |
| scsiDeviceStatGroup | 1.3.6.1.2.1.139.3.2.14 | A collection of statistics regarding SCSI devices and ports. | ||
| scsiDeviceTable | 1.3.6.1.2.1.139.2.1.2 | not-accessible | A list of SCSI devices contained in each of the SCSI manageable instances that this agent is reporting. | |
| scsiDiscoveryGroup | 1.3.6.1.2.1.139.3.2.3 | This group is relevant for the discovered SCSI target devices by a SCSI initiator port. | ||
| scsiDiscoveryHSStatsGroup | 1.3.6.1.2.1.139.3.2.13 | This group is a collection of high speed statistics for all implementations of the SCSI MIB module that contain discovered SCSI initiator devices. | ||
| scsiDiscoveryStatsGroup | 1.3.6.1.2.1.139.3.2.12 | This group is a collection of statistics for all implementations of the SCSI MIB module that contain discovered SCSI initiator devices. | ||
| scsiDscLunEntry | 1.3.6.1.2.1.139.2.2.3.2.1 | not-accessible | An entry (row) represents a discovered LUN at a particular SCSI target device (scsiDscTgtIndex), where the LUN was discovered by a particular local SCSI initiator device within a particular SCSI instance, possibly via a particular local SCSI initiator port. Note that when an entry in the scsiDscTgtTable is deleted, all corresponding entries in this table should automatically be deleted. | |
| SCS scsiDscLunIdAssociation | 1.3.6.1.2.1.139.2.2.3.3.1.3 | ScsiIdAssociation | read-only | This object specifies what the identifier is associated with (e.g., with the addressed physical/logical device or with a particular port). The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page. |
| SCS scsiDscLunIdCodeSet | 1.3.6.1.2.1.139.2.2.3.3.1.2 | ScsiIdCodeSet | read-only | This object specifies the code set in use with this identifier. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page. |
| scsiDscLunIdEntry | 1.3.6.1.2.1.139.2.2.3.3.1 | not-accessible | An entry (row) represents the LU identifier of a discovered LUN at a particular SCSI target device (scsiDscTgtIndex), where the LUN was discovered by a particular local SCSI initiator device within a particular SCSI instance, possibly via a particular local SCSI initiator port. | |
| SCS scsiDscLunIdIndex | 1.3.6.1.2.1.139.2.2.3.3.1.1 | ScsiIndexValue | not-accessible | This object is an arbitrary integer used to uniquely identify a particular LUN identifier discovered by each SCSI initiator device or particular SCSI initiator port within a particular SCSI instance. |
| scsiDscLunIdTable | 1.3.6.1.2.1.139.2.2.3.3 | not-accessible | This table includes all the known LU identifiers of the remote (not in the local system) logical units discovered via each local SCSI initiator port or device of this SCSI instance. | |
| SCS scsiDscLunIdType | 1.3.6.1.2.1.139.2.2.3.3.1.4 | ScsiIdType | read-only | This object specifies the type of the identifier. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page. |
| SCS scsiDscLunIdValue | 1.3.6.1.2.1.139.2.2.3.3.1.5 | ScsiIdValue | read-only | This object represents the actual value of this identifier. The format is defined by the objects scsiDscLunIdCodeSet, scsiDscLunIdAssociation, scsiDscLunIdType. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page. |
| SCS scsiDscLunIndex | 1.3.6.1.2.1.139.2.2.3.2.1.1 | ScsiIndexValue | not-accessible | This object is an arbitrary integer used to uniquely identify a particular LUN discovered by a particular SCSI initiator port or a particular SCSI initiator device within a particular SCSI instance. Entries in the scsiDscLunIdTable are associated with a LUN by having the value of this object in their INDEX. |
| SCS scsiDscLunLun | 1.3.6.1.2.1.139.2.2.3.2.1.2 | ScsiLUN | read-only | This object contains the Logical Unit Number (LUN) of the discovered logical unit. |
| scsiDscLunTable | 1.3.6.1.2.1.139.2.2.3.2 | not-accessible | This table includes all the remote (not in the local system) logical unit numbers (LUNs) discovered via each local SCSI initiator port of each local device within a particular SCSI instance. | |
| T/F scsiDscTgtConfigured | 1.3.6.1.2.1.139.2.2.3.1.1.5 | TruthValue | read-create | This object means -true(1): this entry has been configured by an administrator. -false(2): this entry has been added from a discovery mechanism (e.g., SendTargets, SLP, iSNS). An administrator can modify this value from false to true. |
| SCS scsiDscTgtDevOrPort | 1.3.6.1.2.1.139.2.2.3.1.1.3 | ScsiDeviceOrPort | read-create | This object indicates whether this entry describes a configured SCSI target device name (and applies to all ports on the identified SCSI target device) or an individual SCSI target port. |
| T/F scsiDscTgtDiscovered | 1.3.6.1.2.1.139.2.2.3.1.1.6 | TruthValue | read-only | This object means -true(1): this entry has been discovered by the SCSI instance as result of an automatic discovery process. -false(2):this entry has been added by manual configuration. This entry is read-only because an administrator cannot change it. Note that it is an implementation decision to determine how long to retain a row with configured=false, such as when the SCSI target device is no longer visible/accessible to the local SCSI initiator device. |
| scsiDscTgtEntry | 1.3.6.1.2.1.139.2.2.3.1.1 | not-accessible | Each entry (row) contains information about the SCSI target device or port to which this SCSI initiator port (or all SCSI initiator ports in the SCSI initiator entry indexed by scsiInstIndex, scsiDeviceIndex) will attempt to attach. The entry is either for all local ports (if scsiDscTgtIntrPortIndex is zero) or only for the specific SCSI initiator port identified by scsiDscTgtIntrPortIndex. Note that if an entry in this table is deleted, any corresponding entries in the scsiDscLunsTable must be deleted as well. The StorageType of a row in this table is specified by the instance of scsiInstStorageType that is INDEXed by the same value of scsiInstIndex. | |
| C64 scsiDscTgtHSInCommands | 1.3.6.1.2.1.139.2.2.3.1.1.10 | Counter64 | read-only | This object represents the number of commands received by this SCSI target port or device. This object provides support for system that can quickly generate a large number of commands because they run at high speed. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiDscTgtLastCreation. |
| C32 scsiDscTgtInCommands | 1.3.6.1.2.1.139.2.2.3.1.1.7 | Counter32 | read-only | This object represents the number of commands received from this SCSI target port or device. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiDscTgtLastCreation. |
| SCS scsiDscTgtIndex | 1.3.6.1.2.1.139.2.2.3.1.1.2 | ScsiIndexValue | not-accessible | This object is an arbitrary integer used to uniquely identify a particular SCSI target device either discovered by, or configured for use with, one or more ports scsiDscTgtName of a particular device within a particular SCSI instance. |
| SCS scsiDscTgtIntrPortIndex | 1.3.6.1.2.1.139.2.2.3.1.1.1 | ScsiPortIndexValueOrZero | not-accessible | This object relates to a particular local device within a particular SCSI instance and specifies - the index of the local SCSI initiator port, - or zero, if this entry refers to the local device and therefore refers to all the local SCSI initiator ports. |
| TIM scsiDscTgtLastCreation | 1.3.6.1.2.1.139.2.2.3.1.1.11 | TimeStamp | read-only | This object represents the value of sysUpTime when this row was created. |
| SCS scsiDscTgtName | 1.3.6.1.2.1.139.2.2.3.1.1.4 | ScsiName | read-create | This object represents the name of this configured or discovered SCSI target device or port depending on the value of scsiDscTgtDevOrPort. |
| C32 scsiDscTgtReadMegaBytes | 1.3.6.1.2.1.139.2.2.3.1.1.9 | Counter32 | read-only | This object represents the amount of megabytes received as the result of READ commands to this SCSI target port or device. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiDscTgtLastCreation. |
| ROW scsiDscTgtRowStatus | 1.3.6.1.2.1.139.2.2.3.1.1.12 | RowStatus | read-create | This object allows an administrator to configure dynamically a new entry in this table via SNMP or eventually delete it. An administrator is not allowed to delete an entry for which the value of the object scsiIntrDscTgtDiscovered is equal to true. Note that when an entry in this table is deleted, then any corresponding entries in the scsiDscLunsTable must also be automatically deleted. A newly created row cannot be made active until a value has been set for scsiDscTgtName. In this case, the value of the corresponding instance of the scsiDscTgtRowStatus column will stay 'notReady'. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified. |
| scsiDscTgtTable | 1.3.6.1.2.1.139.2.2.3.1 | not-accessible | This table includes all the remote (not in the local system) SCSI target ports that are authorized to attach to each local SCSI initiator port of this SCSI instance. | |
| C32 scsiDscTgtWrittenMegaBytes | 1.3.6.1.2.1.139.2.2.3.1.1.8 | Counter32 | read-only | This object represents the amount of megabytes of data sent as the result of WRITE commands to this SCSI target port or device. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiDscTgtLastCreation. |
| scsiGeneral | 1.3.6.1.2.1.139.2.1 | |||
| scsiGroups | 1.3.6.1.2.1.139.3.2 | |||
| scsiInitiatorDevHSStatsGroup | 1.3.6.1.2.1.139.3.2.11 | This group is a collection of high speed statistics for all implementations of the SCSI MIB module that contain SCSI initiator devices. | ||
| scsiInitiatorDevice | 1.3.6.1.2.1.139.2.2 | |||
| scsiInitiatorDeviceGroup | 1.3.6.1.2.1.139.3.2.2 | This group is relevant for s SCSI initiator device and port. | ||
| scsiInitiatorDevStatsGroup | 1.3.6.1.2.1.139.3.2.10 | This group is a collection of statistics for all implementations of the SCSI MIB module that contain SCSI initiator devices. | ||
| STR scsiInstAlias | 1.3.6.1.2.1.139.2.1.1.1.2 | SnmpAdminString | read-write | This object represents an administrative string, configured by the administrator. It can be a zero-length string. |
| scsiInstanceEntry | 1.3.6.1.2.1.139.2.1.1.1 | not-accessible | An entry (row) containing management information applicable to a particular SCSI instance. | |
| scsiInstanceTable | 1.3.6.1.2.1.139.2.1.1 | not-accessible | A list of SCSI instances present on the system. The SCSI instance is the top-level entity, to which everything else belongs. An SNMP agent could represent more than one instance if it represents either a stack of devices, or virtual partitions of a larger device, or a host running multiple SCSI implementations from different vendors. | |
| SCS scsiInstIndex | 1.3.6.1.2.1.139.2.1.1.1.1 | ScsiIndexValue | not-accessible | This object represents an arbitrary integer used to uniquely identify a particular SCSI instance. |
| T/F scsiInstScsiNotificationsEnable | 1.3.6.1.2.1.139.2.1.1.1.5 | TruthValue | read-write | This object indicates whether notifications defined in this MIB module will be generated. |
| SCS scsiInstSoftwareIndex | 1.3.6.1.2.1.139.2.1.1.1.3 | ScsiHrSWInstalledIndexOrZero | read-only | If this management instance corresponds to an installed software module, then this object's value is the value of the hrSWInstalledIndex of that module. If there is no correspondence to an installed software module (or no module that has an hrSWInstalledIndex value), then the value of this object is zero. |
| STO scsiInstStorageType | 1.3.6.1.2.1.139.2.1.1.1.6 | StorageType | read-write | This object specifies the memory realization for this SCSI entity. Specifically, each row in the following tables: scsiIntrDevTable scsiDscTgtTable scsiAuthorizedIntrTable scsiLunMapTable has a StorageType as specified by the instance of this object that is INDEXed by the same value of scsiInstIndex. This value of this object is also used to indicate the persistence across reboots of writable values in its row of the scsiInstanceTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row, nor to any object belonging to a table whose entry is INDEXed by the same value of scsiInstIndex. |
| STR scsiInstVendorVersion | 1.3.6.1.2.1.139.2.1.1.1.4 | SnmpAdminString | read-only | This object represents a text string set by the manufacturer describing the version of this instance. The format of this string is determined solely by the manufacturer and is for informational purposes only. It is unrelated to the SCSI specification version numbers. |
| scsiIntrDevEntry | 1.3.6.1.2.1.139.2.2.1.1 | not-accessible | An entry (row) containing information applicable to a SCSI initiator device within a particular SCSI instance. | |
| C32 scsiIntrDevOutResets | 1.3.6.1.2.1.139.2.2.1.1.2 | Counter32 | read-only | This object represents the total number of times that this SCSI initiator device has issued - a LOGICAL UNIT RESET or TARGET RESET task management request, or - any other SCSI transport protocol-specific action or event that causes a Logical Unit Reset or a Hard Reset at one or more SCSI target ports ([SAM2] chapters 5.9.6, 5.9.7). Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| scsiIntrDevTable | 1.3.6.1.2.1.139.2.2.1 | not-accessible | This table contains information for each local SCSI initiator device in each instance. | |
| INT scsiIntrDevTgtAccessMode | 1.3.6.1.2.1.139.2.2.1.1.1 | INTEGER | read-write | This object controls whether or not a discovered SCSI target device is immediately authorized: - autoEnable (2) means that when a SCSI initiator device discovers a SCSI target device, it can use it immediately. - manualEnable (3) means that the SCSI initiator device must wait for an operator to set scsiIntrDscTgtConfigured = true before it is authorized. The StorageType of this object is specified by the instance of scsiInstStorageType that is INDEXed by the same value of scsiInstIndex. |
| scsiIntrPortEntry | 1.3.6.1.2.1.139.2.2.2.1 | not-accessible | An entry (row) containing information applicable to a particular SCSI initiator port of a particular SCSI device within a SCSI instance. | |
| C64 scsiIntrPortHSOutCommands | 1.3.6.1.2.1.139.2.2.2.1.6 | Counter64 | read-only | This object represents the number of commands sent by this SCSI initiator port. This object provides support for systems that can quickly generate a large number of commands because they run at high speed. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| OID scsiIntrPortIdentifier | 1.3.6.1.2.1.139.2.2.2.1.2 | ScsiIdentifier | read-only | This object represents the identifier of the port in one of the format(s) appropriate for the type of transport in use. |
| SCS scsiIntrPortName | 1.3.6.1.2.1.139.2.2.2.1.1 | ScsiName | read-only | This object represents the name of the port assigned for use by the SCSI protocol. The format will depend on the type of transport this port is using. |
| C32 scsiIntrPortOutCommands | 1.3.6.1.2.1.139.2.2.2.1.3 | Counter32 | read-only | This object represents the number of commands sent by this SCSI initiator port. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| C32 scsiIntrPortReadMegaBytes | 1.3.6.1.2.1.139.2.2.2.1.5 | Counter32 | read-only | This object represents the amount of data in megabytes received by this SCSI initiator port. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| scsiIntrPortTable | 1.3.6.1.2.1.139.2.2.2 | not-accessible | This table contains all the SCSI initiator ports for each local SCSI initiator or target/initiator devices in each SCSI instance. | |
| C32 scsiIntrPortWrittenMegaBytes | 1.3.6.1.2.1.139.2.2.2.1.4 | Counter32 | read-only | This object represents the amount of data in megabytes sent by this SCSI initiator port. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| scsiLogicalUnit | 1.3.6.1.2.1.139.2.4 | |||
| SCS scsiLuDefaultLun | 1.3.6.1.2.1.139.2.4.1.1.2 | ScsiLUN | read-only | This object represents the default Logical Unit Number (LUN) for this logical unit; if a SCSI initiator device has not been configured to view this logical unit via an entry in the ScsiLunMapTable, the LU will be visible as scsiLuDefaultLun. If this logical unit does not have a default LUN, it will only be visible if specified via the ScsiLunMapTable, and this object will contain a zero-length string. |
| scsiLuEntry | 1.3.6.1.2.1.139.2.4.1.1 | not-accessible | An entry (row) contains information applicable to a particular logical unit of a particular local SCSI target device within a particular SCSI instance. | |
| C64 scsiLuHSInCommands | 1.3.6.1.2.1.139.2.4.1.1.15 | Counter64 | read-only | This object represents the number of commands received by this logical unit. This object provides support for systems that can quickly generate a large number of commands because they run at high speed. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation. |
| SCS scsiLuIdAssociation | 1.3.6.1.2.1.139.2.4.2.1.3 | ScsiIdAssociation | read-only | This object specifies what the identifier is associated with (e.g., with the addressed physical/logical device or with a particular port). The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page. |
| SCS scsiLuIdCodeSet | 1.3.6.1.2.1.139.2.4.2.1.2 | ScsiIdCodeSet | read-only | This object specifies the code set in use with this identifier. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page. |
| scsiLuIdEntry | 1.3.6.1.2.1.139.2.4.2.1 | not-accessible | An entry (row) containing information applicable to a particular identifier for a particular logical unit of a particular SCSI target device within a particular SCSI instance. | |
| SCS scsiLuIdIndex | 1.3.6.1.2.1.139.2.4.2.1.1 | ScsiIndexValue | not-accessible | This object represents an arbitrary integer used to uniquely identify a particular LU identifier within a particular logical unit within a particular SCSI target device within a particular SCSI instance. |
| scsiLuIdTable | 1.3.6.1.2.1.139.2.4.2 | not-accessible | A table of identifiers for all logical units exposed by the local SCSI target device. | |
| SCS scsiLuIdType | 1.3.6.1.2.1.139.2.4.2.1.4 | ScsiIdType | read-only | This object specifies the type of the identifier. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page. |
| SCS scsiLuIdValue | 1.3.6.1.2.1.139.2.4.2.1.5 | ScsiIdValue | read-only | This object represents the actual value of this identifier. The format is defined by the objects scsiLuIdCodeSet, scsiLuIdAssociation, scsiLuIdType. The value is represented in the same format as is contained in the identifier's Identification Descriptor within the logical unit's Device Identification Page. |
| C32 scsiLuInCommands | 1.3.6.1.2.1.139.2.4.1.1.10 | Counter32 | read-only | This object represents the number of commands received by this logical unit. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation. |
| SCS scsiLuIndex | 1.3.6.1.2.1.139.2.4.1.1.1 | ScsiIndexValue | not-accessible | This object represents an arbitrary integer used to uniquely identify a particular logical unit within a particular SCSI target device within a particular SCSI instance. |
| C32 scsiLuInResets | 1.3.6.1.2.1.139.2.4.1.1.13 | Counter32 | read-only | This object represents the number of times that this logical unit received - a LOGICAL UNIT RESET or TARGET RESET task management request, or - any other SCSI transport protocol-specific action or event that causes a Logical Unit Reset or a Hard Reset at a SCSI target port of the containing device ([SAM2] Chapters 5.9.6, 5.9.7). Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation. |
| TIM scsiLuLastCreation | 1.3.6.1.2.1.139.2.4.1.1.16 | TimeStamp | read-only | This object indicates the value of sysUpTime when this row was last created. |
| scsiLunMapEntry | 1.3.6.1.2.1.139.2.4.3.1 | not-accessible | An entry containing information about the mapping of a particular logical unit to a particular LUN. The set of entries that all have the same values of scsiInstIndex, scsiDeviceIndex and scsiLunMapIndex constitutes a LUN map within a particular SCSI instance. The StorageType of a row in this table is specified by the instance of scsiInstStorageType that is INDEX-ed by the same value of scsiInstIndex. | |
| scsiLunMapGroup | 1.3.6.1.2.1.139.3.2.5 | This group is a collection of attributes regarding the mapping between Logical Unit Number, logical unit, and target device. | ||
| scsiLunMapHSStatsGroup | 1.3.6.1.2.1.139.3.2.9 | This group is a collection of high speed statistics regarding SCSI initiator devices authorized to attach local logical unit and SCSI target device. | ||
| SCS scsiLunMapIndex | 1.3.6.1.2.1.139.2.4.3.1.1 | ScsiIndexValue | not-accessible | This object represents an arbitrary integer used to uniquely identify a particular LunMap within a particular SCSI target device within a particular SCSI instance. |
| SCS scsiLunMapLuIndex | 1.3.6.1.2.1.139.2.4.3.1.3 | ScsiIndexValue | read-create | This object identifies the logical unit for which the value of scsiLuIndex is the same as the value of this object. The identified logical unit is the one mapped to a LUN by this row. |
| SCS scsiLunMapLun | 1.3.6.1.2.1.139.2.4.3.1.2 | ScsiLUN | not-accessible | This object specifies the Logical Unit Number, to which a logical unit is mapped by this row. |
| ROW scsiLunMapRowStatus | 1.3.6.1.2.1.139.2.4.3.1.4 | RowStatus | read-create | This object allows an administrator to create and delete this entry. |
| scsiLunMapStatsGroup | 1.3.6.1.2.1.139.3.2.8 | This group is a collection of statistics regarding SCSI initiator devices authorized to attach local logical unit and SCSI target device. | ||
| scsiLunMapTable | 1.3.6.1.2.1.139.2.4.3 | not-accessible | This table provides the ability to present a logical unit using different Logical Unit Numbers for different SCSI initiator devices. This table provides a mapping between a logical unit and a Logical Unit Number, and can be referenced by a ScsiAuthorizedIntrEntry to specify the LUN map for that initiator. | |
| C32 scsiLuOutTaskSetFullStatus | 1.3.6.1.2.1.139.2.4.1.1.14 | Counter32 | read-only | This object represents the number of Task Set full statuses issued for this logical unit. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation. |
| U32 scsiLuPeripheralType | 1.3.6.1.2.1.139.2.4.1.1.7 | Unsigned32 | read-only | This object is the value returned by SCSI Standard INQUIRY data. It can be: direct-access device, sequential-access device, printer, communication device and so on. The values that can be returned here are defined in SCSI Primary Commands -2. |
| STR scsiLuProductId | 1.3.6.1.2.1.139.2.4.1.1.5 | SnmpAdminString | read-only | This object represents a string identifying the product for this LU as reported in the Standard INQUIRY data. |
| C32 scsiLuReadMegaBytes | 1.3.6.1.2.1.139.2.4.1.1.11 | Counter32 | read-only | This object represents the amount of data in megabytes read from this logical unit. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation. |
| STR scsiLuRevisionId | 1.3.6.1.2.1.139.2.4.1.1.6 | SnmpAdminString | read-only | This object represents a string defining the product revision of this LU as reported in the Standard INQUIRY data. |
| BIT scsiLuState | 1.3.6.1.2.1.139.2.4.1.1.9 | Bits | read-only | This object represents the state of a logical unit and its meaning according to the bit position: 0 Data lost: Within the logical unit data has been lost. 1 Dynamic reconfiguration in progress: The logical unit is being reconfigured. In this state all data is still protected. 2 Exposed: Within the logical unit data is not protected. In this state all data is still valid; however, loss of data or data availability is unavoidable in the event of a failure. 3 Fractionally exposed: Within the logical unit part of the data is not protected. In this state all data is still valid; however, a failure may cause a loss of data or a loss of data availability. 4 Partially exposed: Within the logical unit one or more underlying storage devices have failed. In this state all data is still protected. 5 Protected rebuild: The logical unit is in the process of a rebuild operation. In this state all data is protected. 6 Protection disabled: Within the logical unit the data protection method has been disabled. In this state all data is still valid; however, loss of data or data availability is unavoidable in the event of a failure. 7 Rebuild: The data protection method is in the process of rebuilding data. In this state data is not protected. 8 Recalculate: The logical unit is in the process of a recalculate operation. 9 Spare in use: Within the logical unit a storage device in full or part is being used to store data. In this state all data is still protected. 10 Verify in progress: Within the logical unit data is being verified. |
| INT scsiLuStatus | 1.3.6.1.2.1.139.2.4.1.1.8 | INTEGER | read-only | This object represents the status of this logical unit: - unknown(1): The status of this logical unit cannot be determined. - available(2): The logical unit is fully operational (i.e., accepts media access SCSI commands and has no state information to report). - notAvailable(3): The logical unit is capable of being supported but is not available (i.e., no logical unit is currently present or the logical unit is present but not configured for use). - broken(4): The logical unit has failed and cannot respond to SCSI commands. - readying(5): The logical unit is being initialized and access is temporarily limited. - abnormal(6): The logical unit has state information available that indicates it is operating with limits. The scsiLuState indicates what those limits are. |
| NTF scsiLuStatusChanged | 1.3.6.1.2.1.139.0.0.2 | This notification will be generated each time that scsiLuStatus changes providing that the SCSI instance's value of scsiInstScsiNotificationsEnable is enabled. An SNMP agent implementing the SCSI MIB module should not send more than three SCSI identical notifications in any 10-second period. | ||
| scsiLuTable | 1.3.6.1.2.1.139.2.4.1 | not-accessible | This table contains the logical units exposed by local SCSI target devices. It includes attributes for the World Wide Name (WWN), scsiLuVendorId, scsiLuProductId, and scsiLuRevisionId, which may also appear in the scsiLuIdTable. If an implementation exposes a WWN as a LuIdTable entry, it must match the scsiLuWwnName in this table. If an implementation exposes a (vendor, product, revision) identifier as an LuIdTable entry, each of these fields must match the scsiLuVendorId, scsiLuProductId, and scsiLuRevisionId attributes in this table. | |
| STR scsiLuVendorId | 1.3.6.1.2.1.139.2.4.1.1.4 | SnmpAdminString | read-only | This object represents a string identifying the vendor of this LU as reported in the Standard INQUIRY data. |
| C32 scsiLuWrittenMegaBytes | 1.3.6.1.2.1.139.2.4.1.1.12 | Counter32 | read-only | This object represents the amount of data in megabytes written to this logical unit. Discontinuities in the value of this counter can occur at re- initialization of the management system, and at other times as indicated by the value of scsiLuLastCreation. |
| SCS scsiLuWwnName | 1.3.6.1.2.1.139.2.4.1.1.3 | ScsiLuNameOrZero | read-only | This object represents the World Wide Name of this LU that is the device identifier of the Vital Product Data (VPD) page name; if there is no WWN for this LU, this object will contain a zero-length string. If there is more than one identifier, they will be listed in the scsiLuIdTable and this object will contain a zero-length string. |
| scsiMIB | 1.3.6.1.2.1.139 | The SCSI MIB Module. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4455; see the RFC itself for full legal notices. | ||
| scsiNotifications | 1.3.6.1.2.1.139.0 | |||
| scsiNotificationsPrefix | 1.3.6.1.2.1.139.0.0 | |||
| scsiObjects | 1.3.6.1.2.1.139.2 | |||
| C32 scsiPortBusyStatusesEx | 1.3.6.1.2.1.139.2.1.3.1.4 | Counter32 | read-only | This object represents the number of port busy statuses sent or received by this port. Note: Initiator ports only receive busy status and SCSI target ports only send busy status. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| scsiPortEntry | 1.3.6.1.2.1.139.2.1.3.1 | not-accessible | An entry (row) containing management information applicable to a particular SCSI port of a particular SCSI device in a particular SCSI instance. | |
| SCS scsiPortIndex | 1.3.6.1.2.1.139.2.1.3.1.1 | ScsiIndexValue | not-accessible | An arbitrary integer used to uniquely identify a particular port of a given device within a particular SCSI instance. |
| BIT scsiPortRole | 1.3.6.1.2.1.139.2.1.3.1.2 | Bits | read-only | This object indicates whether this port is acting as a SCSI initiator port, or as a SCSI target port or as both. |
| scsiPortTable | 1.3.6.1.2.1.139.2.1.3 | not-accessible | A list of SCSI ports for each SCSI device in each instance. | |
| NUM scsiPortTransportPtr | 1.3.6.1.2.1.139.2.1.3.1.3 | RowPointer | read-only | This object is a pointer to the corresponding row in the scsiTransportTable. This row contains information on the transport such as transport type and port name. |
| scsiRemoteIntrDev | 1.3.6.1.2.1.139.2.3.3 | |||
| scsiRemoteTgtDev | 1.3.6.1.2.1.139.2.2.3 | |||
| scsiTargetDevHSStatsGroup | 1.3.6.1.2.1.139.3.2.7 | This group is a collection of high speed statistics for all implementations of the SCSI MIB module that contain SCSI target devices. | ||
| scsiTargetDevice | 1.3.6.1.2.1.139.2.3 | |||
| scsiTargetDeviceGroup | 1.3.6.1.2.1.139.3.2.4 | This group is relevant for a SCSI target device and port. | ||
| scsiTargetDevStatsGroup | 1.3.6.1.2.1.139.3.2.6 | This group is a collection of statistics for all implementations of the SCSI MIB module that contain SCSI target devices. | ||
| scsiTgtDevEntry | 1.3.6.1.2.1.139.2.3.1.1 | not-accessible | An entry (row) containing information applicable to a particular local SCSI target device within a particular SCSI instance. | |
| INT scsiTgtDeviceStatus | 1.3.6.1.2.1.139.2.3.1.1.2 | INTEGER | read-only | This object represents the status of this SCSI device, summarizing the state of both the addressable devices (i.e., the logical units) and the non-addressable devices within this SCSI device: - unknown(1): This value is used when the status cannot be determined - available(2): All addressable and non-addressable devices within the SCSI device are fully operational (i.e., no logical units have an abnormal status). - broken(3): The SCSI device is not operational and cannot be made operational without external intervention. - readying(4): One or more logical units within the SCSI device are being initialized and access to the SCSI device is temporarily limited (i.e., one or more of the logical units have a readying status). - abnormal(5): One or more addressable devices within the SCSI device are indicating a status other than available; nevertheless, the SCSI device is operational (i.e., one or more of the logical units have an abnormal status). - nonAddrFailure(6): One or more non-addressable devices within the SCSI device have failed; nevertheless, the SCSI device is operational (i.e., no logical units have an abnormal or readying status). - nonAddrFailReadying(7): One or more non-addressable devices within the SCSI device have failed; nevertheless, one or more logical units within the SCSI device are being initialized and access to the SCSI device is temporarily limited. - nonAddrFailAbnormal(8): One or more non-addressable devices within the SCSI device have failed and one or more addressable devices within the SCSI device are indicating a status other than available; however, the SCSI device is operational. |
| NTF scsiTgtDeviceStatusChanged | 1.3.6.1.2.1.139.0.0.1 | This notification will be generated for each occurrence of the abnormal status (e.g., if the SCSI target device's current status is abnormal) providing that the SCSI instance's value of scsiInstScsiNotificationsEnable is enabled. An SNMP agent implementing the SCSI MIB module should not send more than three SCSI identical notifications in any 10-second period. | ||
| scsiTgtDevLuNotificationsGroup | 1.3.6.1.2.1.139.3.2.15 | A collection of notifications regarding status change of SCSI target devices and logical units. | ||
| G32 scsiTgtDevNonAccessibleLUs | 1.3.6.1.2.1.139.2.3.1.1.3 | Gauge32 | read-only | This object is the number of logical units existing but not currently accessible via this local SCSI target device. |
| G32 scsiTgtDevNumberOfLUs | 1.3.6.1.2.1.139.2.3.1.1.1 | Gauge32 | read-only | This object is the number of logical units accessible via this local SCSI target device. |
| C32 scsiTgtDevResets | 1.3.6.1.2.1.139.2.3.1.1.4 | Counter32 | read-only | This object counts the number of hard resets encountered by this SCSI target device. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| scsiTgtDevTable | 1.3.6.1.2.1.139.2.3.1 | not-accessible | This table contains information about each local SCSI target device. | |
| scsiTgtPortEntry | 1.3.6.1.2.1.139.2.3.2.1 | not-accessible | An entry (row) containing information applicable to a particular local SCSI target port of a particular local SCSI target device within a particular SCSI instance. | |
| C64 scsiTgtPortHSInCommands | 1.3.6.1.2.1.139.2.3.2.1.6 | Counter64 | read-only | This object represents the number of commands received. This object provides support for systems that can quickly generate a large number of commands because they run at high speed. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| OID scsiTgtPortIdentifier | 1.3.6.1.2.1.139.2.3.2.1.2 | ScsiIdentifier | read-only | This object represents the identifier of the port in one of the format(s) appropriate for the type of transport. |
| C32 scsiTgtPortInCommands | 1.3.6.1.2.1.139.2.3.2.1.3 | Counter32 | read-only | This object represents the number of commands received by this SCSI target port. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| SCS scsiTgtPortName | 1.3.6.1.2.1.139.2.3.2.1.1 | ScsiName | read-only | This object represents the name of the port assigned for use in the SCSI protocol. |
| C32 scsiTgtPortReadMegaBytes | 1.3.6.1.2.1.139.2.3.2.1.5 | Counter32 | read-only | This object represents the amount of data read in megabytes by this SCSI target port. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| scsiTgtPortTable | 1.3.6.1.2.1.139.2.3.2 | not-accessible | This table includes all the local SCSI target ports of all the local SCSI target devices. | |
| C32 scsiTgtPortWrittenMegaBytes | 1.3.6.1.2.1.139.2.3.2.1.4 | Counter32 | read-only | This object represents the amount of data written in megabytes by this SCSI target port. Discontinuities in the value of this counter can occur at re- initialization of the management system. |
| SCS scsiTransportDevName | 1.3.6.1.2.1.139.2.1.5.1.4 | ScsiName | read-only | This object represents the name of this device in one of the format(s) appropriate for this type of transport. |
| scsiTransportEntry | 1.3.6.1.2.1.139.2.1.5.1 | not-accessible | An entry (row) containing parameters applicable to a transport used by a particular device of a particular SCSI manageable instance. | |
| scsiTransportFCP | 1.3.6.1.2.1.139.1.1.3 | This identity identifies a Fibre Channel Protocol for SCSI, Second Version. | ||
| SCS scsiTransportIndex | 1.3.6.1.2.1.139.2.1.5.1.1 | ScsiIndexValue | not-accessible | An arbitrary integer used to uniquely identify a particular transport within a given device within a particular SCSI instance. |
| scsiTransportISCSI | 1.3.6.1.2.1.139.1.1.5 | This identity identifies an iSCSI transport. | ||
| scsiTransportOther | 1.3.6.1.2.1.139.1.1.1 | This identity identifies a transport that has no identity; it might happen because the transport is unknown or might not have been defined when this MIB module was created. | ||
| NUM scsiTransportPointer | 1.3.6.1.2.1.139.2.1.5.1.3 | RowPointer | read-only | This object represents a pointer to a conceptual row in a 'transport' MIB module allowing a manager to get useful information for the transport described by this entry. For example, if the transport of this device is iSCSI, this object will point to the iSCSI Instance of the iSCSI MIB module. If there is no MIB for this transport, this object has the value 0.0. |
| scsiTransportSAS | 1.3.6.1.2.1.139.1.1.7 | This identity identifies the Serial Attach SCSI Protocol. | ||
| scsiTransportSBP | 1.3.6.1.2.1.139.1.1.6 | This identity identifies the Serial Bus Protocol 3. | ||
| scsiTransportSPI | 1.3.6.1.2.1.139.1.1.2 | This identity identifies a parallel SCSI transport. | ||
| scsiTransportSRP | 1.3.6.1.2.1.139.1.1.4 | This identity identifies a protocol for transporting SCSI over Remote Direct Memory Access (RDMA) interfaces, e.g., InfiniBand (tm). | ||
| scsiTransportTable | 1.3.6.1.2.1.139.2.1.5 | not-accessible | This table contains the device transport-specific information for each transport connected to each device in scsiDeviceTable. | |
| OID scsiTransportType | 1.3.6.1.2.1.139.2.1.5.1.2 | AutonomousType | read-only | This object identifies the transport type of this row of the transport table. For example, if this object has the value scsiTransportFCP, then the identified transport is FCP. |
| scsiTransportTypes | 1.3.6.1.2.1.139.1.1 |
RFC description
Standard MIB for SCSI (Small Computer System Interface) device management; defines objects for monitoring SCSI host adapters and target devices.
Start monitoring vendor-neutral, standards-based MIB, storage controller/HBA, SAN/storage array (SCSI-layer identity/status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.