RackMonitor-MIB

All MIBs › RackMonitor-MIB

Category: Environmental Monitoring

Description: Tracks environmental conditions in equipment racks, covering temperature, humidity, power consumption, and door sensor status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RackMonitor-MIB?

RackMonitor-MIB is a vendor-specific legacy-style MIB (RFC1155-SMI/RFC-1212) published under enterprises.534 ("powerware"), whose copyright header identifies it as an Eaton Environmental Rack Monitor MIB — the batch's vendor field was left blank, but the source clearly points to Eaton (formerly Powerware) rather than an unbranded device. It models device identity (insIdentManufacturer/Model/AgentSoftwareVersion), network/date-time/logging/Telnet/HTTP/SNMP/trap-receiver configuration, and two dual-sensor probe groups (scSensor1/scSensor2) each carrying configurable temperature and humidity threshold profiles under sensorConfig alongside live current-reading tables under sensorMonitor. It defines an extensive set of TRAP-TYPE notifications for temperature/humidity high/low warning and critical thresholds, alarm-input active/inactive transitions, and communication lost/restored events. This makes it primarily an environmental-alarm MIB for rack-level temperature, humidity, and contact-alarm inputs rather than a network-traffic MIB, deployed alongside Eaton/Powerware UPS and power-distribution gear in data-center racks, and RackMonitor-MIB SNMP monitoring is the standard way to pull live sensor readings and threshold alarms from these probes.

IPNetwork Monitor allows you to monitor SNMP objects defined in RackMonitor-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Eaton/Powerware Rack Monitor environmental monitoring appliances

Monitoring Examples

An operator polls the live sensor tables under sensorMonitor for each rack probe and compares readings against the scSensor1Temperature/scSensor2Temperature threshold profiles configured under sensorConfig; receiving an rmTemperatureHighCritical trap without a matching rmTemperatureNotHighCritical would indicate the rack is still overheating.

What Can Be Monitored

live temperature/humidity sensor readings
configurable temperature/humidity threshold profiles
alarm input active/inactive state
temperature high/low warning & critical traps
humidity high/low warning & critical traps
communication lost/restored events

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
powerware	1.3.6.1.4.1.534
product	1.3.6.1.4.1.534.6
dataCenter	1.3.6.1.4.1.534.6.7
environmentalMonitor	1.3.6.1.4.1.534.6.7.1
insObjects	1.3.6.1.4.1.534.6.7.1.1
rmIdent	1.3.6.1.4.1.534.6.7.1.1.1
STR insIdentManufacturer	1.3.6.1.4.1.534.6.7.1.1.1.1	DisplayString	read-only	The name of the RackMonitor manufacturer.
STR insIdentModel	1.3.6.1.4.1.534.6.7.1.1.1.2	DisplayString	read-only	The RackMonitor Model designation.
STR insIdentAgentSoftwareVersion	1.3.6.1.4.1.534.6.7.1.1.1.3	DisplayString	read-only	The RackMonitor software/firmware version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.
STR insIdentName	1.3.6.1.4.1.534.6.7.1.1.1.4	DisplayString	read-write	A string identifying the RackMonitor. This object should be set by the administrator.
rmConfig	1.3.6.1.4.1.534.6.7.1.1.2
INT rmConfigMibVersion	1.3.6.1.4.1.534.6.7.1.1.2.1	INTEGER	read-only	The version of MIB spec.
rmConfigNetwork	1.3.6.1.4.1.534.6.7.1.1.2.2
IP rmConfigIpAddress	1.3.6.1.4.1.534.6.7.1.1.2.2.1	IpAddress	read-write	The ip address that NMS can identify the managed device
IP rmConfigGateway	1.3.6.1.4.1.534.6.7.1.1.2.2.2	IpAddress	read-write	The default gateway that allow device managed through routers
IP rmConfigSubnetMask	1.3.6.1.4.1.534.6.7.1.1.2.2.3	IpAddress	read-write	Internet address subnet mask
rmConfigDateTime	1.3.6.1.4.1.534.6.7.1.1.2.3
STR rmConfigDate	1.3.6.1.4.1.534.6.7.1.1.2.3.1	DisplayString	read-write	The date in Environmental Rack Monitor, format is (dd/mm/yyyy)
STR rmConfigTime	1.3.6.1.4.1.534.6.7.1.1.2.3.2	DisplayString	read-write	The time in Environmental Rack Monitor, format is (hh:mm:ss)
INT rmConfigTimeFromNtp	1.3.6.1.4.1.534.6.7.1.1.2.3.3	INTEGER	read-write	Enable/disable update of the date and time from the NTP server.
IP rmConfigNtpIpAddress	1.3.6.1.4.1.534.6.7.1.1.2.3.4	IpAddress	read-write	NTP IP address.
INT rmConfigNtpTimeZone	1.3.6.1.4.1.534.6.7.1.1.2.3.5	INTEGER	read-write	Enable/disable update of the date and time from the NTP server.
INT rmConfigDayLightSaving	1.3.6.1.4.1.534.6.7.1.1.2.3.6	INTEGER	read-write	Enable/disable daylight saving for NTP time, if enabled, the time obtained from the NTP will be set one hour in advance to reflect daylight saving status.
rmConfigLog	1.3.6.1.4.1.534.6.7.1.1.2.4
INT rmConfigHistoryLogFrequency	1.3.6.1.4.1.534.6.7.1.1.2.4.1	INTEGER	read-write	The frequency of the history log update. The value is in seconds
INT rmConfigExtHistoryLogFrequency	1.3.6.1.4.1.534.6.7.1.1.2.4.2	INTEGER	read-write	The frequency of the extended history log update. The value is in seconds
INT rmConfigConfigurationLog	1.3.6.1.4.1.534.6.7.1.1.2.4.3	INTEGER	read-write	Enable/Disable Environmental Rack Monitor parameters change logging.
INT rmConfigDhcpStatue	1.3.6.1.4.1.534.6.7.1.1.2.5	INTEGER	read-write	Enable or Disable DHCP/BootP capability
INT rmConfigPingStatue	1.3.6.1.4.1.534.6.7.1.1.2.6	INTEGER	read-write	Enable or Disable Ping Echo capability
INT rmConfigTftpStatue	1.3.6.1.4.1.534.6.7.1.1.2.7	INTEGER	read-write	Enable or Disable TFTP network upgrade capability
rmConfigTelnet	1.3.6.1.4.1.534.6.7.1.1.2.8
INT rmConfigTelnetStatue	1.3.6.1.4.1.534.6.7.1.1.2.8.1	INTEGER	read-write	Enable or Disable telnet access
INT rmConfigTelnetPortNumber	1.3.6.1.4.1.534.6.7.1.1.2.8.2	INTEGER	read-write	Setting the server port for telnet.
rmConfigHttp	1.3.6.1.4.1.534.6.7.1.1.2.9
INT rmConfigHttpStatue	1.3.6.1.4.1.534.6.7.1.1.2.9.1	INTEGER	read-write	Enable or Disable HTTP access
INT rmConfigHttpPortNumber	1.3.6.1.4.1.534.6.7.1.1.2.9.2	INTEGER	read-write	Setting the server port of HTTP.
INT rmConfigHttpSecurity	1.3.6.1.4.1.534.6.7.1.1.2.9.3	INTEGER	read-write	Enable/Disable HTTP access for read-only users
rmConfigSnmp	1.3.6.1.4.1.534.6.7.1.1.2.10
INT rmConfigSnmpStatue	1.3.6.1.4.1.534.6.7.1.1.2.10.1	INTEGER	read-write	Enable or Disable SNMP access
INT rmConfigSnmpPortNumber	1.3.6.1.4.1.534.6.7.1.1.2.10.2	INTEGER	read-write	Setting the server port for SNMP.
rmConfigControl	1.3.6.1.4.1.534.6.7.1.1.2.11
INT rmConfigResetToDefault	1.3.6.1.4.1.534.6.7.1.1.2.11.1	INTEGER	read-write	Reset all parameters of Environmental Rack Monitor to default values
INT rmConfigRestart	1.3.6.1.4.1.534.6.7.1.1.2.11.2	INTEGER	read-write	Restart rm
rmConfigTrap	1.3.6.1.4.1.534.6.7.1.1.2.12
INT rmConfigTrapRetryCount	1.3.6.1.4.1.534.6.7.1.1.2.12.1	INTEGER	read-write	The count of repeat traps to send to NMS before trap acknowledge received.
INT rmConfigTrapRetryTime	1.3.6.1.4.1.534.6.7.1.1.2.12.2	INTEGER	read-write	The time between retry traps sent to NMS.
INT rmConfigTrapAckSignature	1.3.6.1.4.1.534.6.7.1.1.2.12.3	INTEGER	read-write	The signature of trap acknowledge.
INT rmConfigPollRate	1.3.6.1.4.1.534.6.7.1.1.2.13	INTEGER	read-write	The frequency that the Rack Monitor will read from sensors (unit : second).
rmConfigTrapsReceiversTable	1.3.6.1.4.1.534.6.7.1.1.2.14		not-accessible	A list of managers to send traps to. The number of entries is given by the value of rmConfigNumTrapReceivers
rmConfigTrapsReceiversEntry	1.3.6.1.4.1.534.6.7.1.1.2.14.1		not-accessible	The managers to send traps to.
INT trapsIndex	1.3.6.1.4.1.534.6.7.1.1.2.14.1.1	INTEGER	read-only	The index to a trap receiver entry.
IP trapsReceiverAddr	1.3.6.1.4.1.534.6.7.1.1.2.14.1.2	IpAddress	read-write	The IP address of the manager to send a trap to.
STR receiverCommunityString	1.3.6.1.4.1.534.6.7.1.1.2.14.1.3	DisplayString	read-write	The community name to use in the trap when sent to the manager.
INT receiverSeverityLevel	1.3.6.1.4.1.534.6.7.1.1.2.14.1.4	INTEGER	read-write	The severity level of traps to be received by this manager.
STR receiverDescription	1.3.6.1.4.1.534.6.7.1.1.2.14.1.5	DisplayString	read-write	Description of trap receivers
rmConfigAccessControlTable	1.3.6.1.4.1.534.6.7.1.1.2.15		not-accessible	A list of managers which can access rm with private community string.
rmConfigAccessControlEntry	1.3.6.1.4.1.534.6.7.1.1.2.15.1		not-accessible	The managers.
INT accessIndex	1.3.6.1.4.1.534.6.7.1.1.2.15.1.1	INTEGER	read-only	The index to a access control entry.
IP accessControlAddr	1.3.6.1.4.1.534.6.7.1.1.2.15.1.2	IpAddress	read-write	The IP address of the manager to access RackMonitor
STR accessCommunityString	1.3.6.1.4.1.534.6.7.1.1.2.15.1.3	DisplayString	read-write	The community name to use in the manager when access RackMonitor
INT accessControlMode	1.3.6.1.4.1.534.6.7.1.1.2.15.1.4	INTEGER	read-write	Access type, only read/Write access type can change parameter of RackMonitor
INT rmConfigTemperatureUnit	1.3.6.1.4.1.534.6.7.1.1.2.16	INTEGER	read-write	The temperature unit of the system, can be Celsius or Fahrenheit
INT rmConfigDateFormat	1.3.6.1.4.1.534.6.7.1.1.2.17	INTEGER	read-write	The date format of the system, can be dd/mm/yyyy or mm/dd/yyyy
sensorMonitor	1.3.6.1.4.1.534.6.7.1.1.3
INT smSensorNumber	1.3.6.1.4.1.534.6.7.1.1.3.1	INTEGER	read-only	The number of sensors that can be monitored.
smSensorTable	1.3.6.1.4.1.534.6.7.1.1.3.2		not-accessible	A list of sensor devices to be monitored.
smSensorEntry	1.3.6.1.4.1.534.6.7.1.1.3.2.1		not-accessible	The sensor device.
INT smDeviceIndex	1.3.6.1.4.1.534.6.7.1.1.3.2.1.1	INTEGER	read-only	The index to a sensor device entry.
INT smDeviceStatus	1.3.6.1.4.1.534.6.7.1.1.3.2.1.2	INTEGER	read-only	The device type plugged into RackMonitor.
INT smDeviceTemperature	1.3.6.1.4.1.534.6.7.1.1.3.2.1.3	INTEGER	read-only	The temperature of sensor on device RackMonitor, the unit is 0.1 degree.
INT smDeviceTemperatureAlarm	1.3.6.1.4.1.534.6.7.1.1.3.2.1.4	INTEGER	read-only	The status of temperature sensor on device RackMonitor.
INT smDeviceHumidity	1.3.6.1.4.1.534.6.7.1.1.3.2.1.5	INTEGER	read-only	The humidity of sensor on device RackMonitor, the unit is 0.1%.
INT smDeviceHumidityAlarm	1.3.6.1.4.1.534.6.7.1.1.3.2.1.6	INTEGER	read-only	The device type plugged into RackMonitor.
INT smAlarm1	1.3.6.1.4.1.534.6.7.1.1.3.2.1.7	INTEGER	read-only	The device type plugged into RackMonitor.
INT smAlarm2	1.3.6.1.4.1.534.6.7.1.1.3.2.1.8	INTEGER	read-only	The device type plugged into RackMonitor.
sensorConfig	1.3.6.1.4.1.534.6.7.1.1.4
INT scSensorNumber	1.3.6.1.4.1.534.6.7.1.1.4.1	INTEGER	read-only	The number of sensors that can be plugged into RackMonitor.
scSensorTable	1.3.6.1.4.1.534.6.7.1.1.4.2		not-accessible	A list of sensor devices to be configured.
scSensorEntry	1.3.6.1.4.1.534.6.7.1.1.4.2.1		not-accessible	The sensor device.
INT scDeviceIndex	1.3.6.1.4.1.534.6.7.1.1.4.2.1.1	INTEGER	read-only	The index to a sensor device entry.
STR scDeviceName	1.3.6.1.4.1.534.6.7.1.1.4.2.1.2	DisplayString	read-write	The name of the sensor device for identification.
INT scDeviceState	1.3.6.1.4.1.534.6.7.1.1.4.2.1.3	INTEGER	read-write	The setup of sensor device type.
scSensor1	1.3.6.1.4.1.534.6.7.1.1.4.3
STR scSensor1DeviceName	1.3.6.1.4.1.534.6.7.1.1.4.3.1	DisplayString	read-write	The name of sensor device.
INT scSensor1DeviceState	1.3.6.1.4.1.534.6.7.1.1.4.3.2	INTEGER	read-write	The setup of sensor device type.
scSensor1Temperature	1.3.6.1.4.1.534.6.7.1.1.4.3.3
STR scSensor1TemperatureName	1.3.6.1.4.1.534.6.7.1.1.4.3.3.1	DisplayString	read-write	The temperature sensor name.
INT scSensor1TemperatureLowWarning	1.3.6.1.4.1.534.6.7.1.1.4.3.3.2	INTEGER	read-write	The set point to trigger low warning alarm.
INT scSensor1TemperatureLowCritical	1.3.6.1.4.1.534.6.7.1.1.4.3.3.3	INTEGER	read-write	The threshold to trigger low critical alarm.
INT scSensor1TemperatureHighWarning	1.3.6.1.4.1.534.6.7.1.1.4.3.3.4	INTEGER	read-write	The threshold to trigger high warning alarm.
INT scSensor1TemperatureHighCritical	1.3.6.1.4.1.534.6.7.1.1.4.3.3.5	INTEGER	read-write	The threshold to trigger high critical alarm.
INT scSensor1TemperatureHysteresis	1.3.6.1.4.1.534.6.7.1.1.4.3.3.6	INTEGER	read-write	The set value to prevent too many alarms when temperature is hovering around the set threshold.
INT scSensor1TemperatureCalibration	1.3.6.1.4.1.534.6.7.1.1.4.3.3.7	INTEGER	read-write	The set value to get the correct temperature according to the reference temperature.
INT scSensor1TemperatureLowWarningStatus	1.3.6.1.4.1.534.6.7.1.1.4.3.3.8	INTEGER	read-write	Enable/Disable the set point to trigger low warning alarm.
INT scSensor1TemperatureLowCriticalStatus	1.3.6.1.4.1.534.6.7.1.1.4.3.3.9	INTEGER	read-write	Enable/Disable the set point to trigger low critical alarm.
INT scSensor1TemperatureHighWarningStatus	1.3.6.1.4.1.534.6.7.1.1.4.3.3.10	INTEGER	read-write	Enable/Disable the set point to trigger high warning alarm.
INT scSensor1TemperatureHighCriticalStatus	1.3.6.1.4.1.534.6.7.1.1.4.3.3.11	INTEGER	read-write	Enable/disable the set point to trigger high critical alarm.
scSensor1Humidity	1.3.6.1.4.1.534.6.7.1.1.4.3.4
STR scSensor1HumdityName	1.3.6.1.4.1.534.6.7.1.1.4.3.4.1	DisplayString	read-write	The humidity sensor name.
INT scSensor1HumidityLowWarning	1.3.6.1.4.1.534.6.7.1.1.4.3.4.2	INTEGER	read-write	The set point to trigger low warning alarm.
INT scSensor1HumidityLowCritical	1.3.6.1.4.1.534.6.7.1.1.4.3.4.3	INTEGER	read-write	The threshold to trigger low critical alarm.
INT scSensor1HumidityHighWarning	1.3.6.1.4.1.534.6.7.1.1.4.3.4.4	INTEGER	read-write	The threshold to trigger high warning alarm.
INT scSensor1HumidityHighCritical	1.3.6.1.4.1.534.6.7.1.1.4.3.4.5	INTEGER	read-write	The threshold to trigger high critical alarm.
INT scSensor1HumidityHysteresis	1.3.6.1.4.1.534.6.7.1.1.4.3.4.6	INTEGER	read-write	The set value to prevent too many alarms when Humidity is hovering around the set threshold.
INT scSensor1HumidityCalibration	1.3.6.1.4.1.534.6.7.1.1.4.3.4.7	INTEGER	read-write	The set value to get the correct temperature according to your reference temperature.
INT scSensor1HumidityLowWarningStatus	1.3.6.1.4.1.534.6.7.1.1.4.3.4.8	INTEGER	read-write	Enable/Disable the set point to trigger low warning alarm.
INT scSensor1HumidityLowCriticalStatus	1.3.6.1.4.1.534.6.7.1.1.4.3.4.9	INTEGER	read-write	Enable/Disable the set point to trigger low critical alarm.
INT scSensor1HumidityHighWarningStatus	1.3.6.1.4.1.534.6.7.1.1.4.3.4.10	INTEGER	read-write	Enable/Disable the set point to trigger high warning alarm.
INT scSensor1HumidityHighCriticalStatus	1.3.6.1.4.1.534.6.7.1.1.4.3.4.11	INTEGER	read-write	Enable/Disable the set point to trigger high critical alarm.
scSensor1Alarm1	1.3.6.1.4.1.534.6.7.1.1.4.3.5
STR scSensor1Alarm1Name	1.3.6.1.4.1.534.6.7.1.1.4.3.5.1	DisplayString	read-write	The name of alarm-1.
INT scSensor1Alarm1State	1.3.6.1.4.1.534.6.7.1.1.4.3.5.2	INTEGER	read-write	Setup the signal type to trigger alarm.
INT scSensor1Alarm1Hysteresis	1.3.6.1.4.1.534.6.7.1.1.4.3.5.3	INTEGER	read-write	The set value to delay the alarm triggered when event occurs.
scSensor1Alarm2	1.3.6.1.4.1.534.6.7.1.1.4.3.6
STR scSensor1Alarm2Name	1.3.6.1.4.1.534.6.7.1.1.4.3.6.1	DisplayString	read-write	The name of alarm-1.
INT scSensor1Alarm2State	1.3.6.1.4.1.534.6.7.1.1.4.3.6.2	INTEGER	read-write	Setup the signal type to trigger alarm.
INT scSensor1Alarm2Hysteresis	1.3.6.1.4.1.534.6.7.1.1.4.3.6.3	INTEGER	read-write	The set value to delay the alarm triggered when event occurs.
scSensor2	1.3.6.1.4.1.534.6.7.1.1.4.4
STR scSensor2DeviceName	1.3.6.1.4.1.534.6.7.1.1.4.4.1	DisplayString	read-write	The name of sensor device.
INT scSensor2DeviceState	1.3.6.1.4.1.534.6.7.1.1.4.4.2	INTEGER	read-write	The setup of sensor device type.
scSensor2Temperature	1.3.6.1.4.1.534.6.7.1.1.4.4.3
STR scSensor2TemperatureName	1.3.6.1.4.1.534.6.7.1.1.4.4.3.1	DisplayString	read-write	The temperature sensor name.
INT scSensor2TemperatureLowWarning	1.3.6.1.4.1.534.6.7.1.1.4.4.3.2	INTEGER	read-write	The set point to trigger low warning alarm.
INT scSensor2TemperatureLowCritical	1.3.6.1.4.1.534.6.7.1.1.4.4.3.3	INTEGER	read-write	The threshold to trigger low critical alarm.
INT scSensor2TemperatureHighWarning	1.3.6.1.4.1.534.6.7.1.1.4.4.3.4	INTEGER	read-write	The threshold to trigger high warning alarm.
INT scSensor2TemperatureHighCritical	1.3.6.1.4.1.534.6.7.1.1.4.4.3.5	INTEGER	read-write	The threshold to trigger high critical alarm.
INT scSensor2TemperatureHysteresis	1.3.6.1.4.1.534.6.7.1.1.4.4.3.6	INTEGER	read-write	The set value to prevent too many alarms when temperature is hovering around the set threshold.
INT scSensor2TemperatureCalibration	1.3.6.1.4.1.534.6.7.1.1.4.4.3.7	INTEGER	read-write	The set value to get the correct temperature according to your reference temperature.
INT scSensor2TemperatureLowWarningStatus	1.3.6.1.4.1.534.6.7.1.1.4.4.3.8	INTEGER	read-write	Enable/Disable the set point to trigger low warning alarm.
INT scSensor2TemperatureLowCriticalStatus	1.3.6.1.4.1.534.6.7.1.1.4.4.3.9	INTEGER	read-write	Enable/Disable the set point to trigger low critical alarm.
INT scSensor2TemperatureHighWarningStatus	1.3.6.1.4.1.534.6.7.1.1.4.4.3.10	INTEGER	read-write	Enable/Disable the set point to trigger high warning alarm.
INT scSensor2TemperatureHighCriticalStatus	1.3.6.1.4.1.534.6.7.1.1.4.4.3.11	INTEGER	read-write	Enable/Disable the set point to trigger high critical alarm.
scSensor2Humidity	1.3.6.1.4.1.534.6.7.1.1.4.4.4
STR scSensor2HumdityName	1.3.6.1.4.1.534.6.7.1.1.4.4.4.1	DisplayString	read-write	The humidity sensor name.
INT scSensor2HumidityLowWarning	1.3.6.1.4.1.534.6.7.1.1.4.4.4.2	INTEGER	read-write	The set point to trigger low warning alarm.
INT scSensor2HumidityLowCritical	1.3.6.1.4.1.534.6.7.1.1.4.4.4.3	INTEGER	read-write	The threshold to trigger low critical alarm.
INT scSensor2HumidityHighWarning	1.3.6.1.4.1.534.6.7.1.1.4.4.4.4	INTEGER	read-write	The threshold to trigger high warning alarm.
INT scSensor2HumidityHighCritical	1.3.6.1.4.1.534.6.7.1.1.4.4.4.5	INTEGER	read-write	The threshold to trigger high critical alarm.
INT scSensor2HumidityHysteresis	1.3.6.1.4.1.534.6.7.1.1.4.4.4.6	INTEGER	read-write	The set value to prevent too many alarms when Humidity is hovering around the set threshold.
INT scSensor2HumidityCalibration	1.3.6.1.4.1.534.6.7.1.1.4.4.4.7	INTEGER	read-write	The set value to get the correct temperature according to the reference temperature.
INT scSensor2HumidityLowWarningStatus	1.3.6.1.4.1.534.6.7.1.1.4.4.4.8	INTEGER	read-write	Enable/Disable the set point to trigger low warning alarm.
INT scSensor2HumidityLowCriticalStatus	1.3.6.1.4.1.534.6.7.1.1.4.4.4.9	INTEGER	read-write	Enable/Disable the set point to trigger low critical alarm.
INT scSensor2HumidityHighWarningStatus	1.3.6.1.4.1.534.6.7.1.1.4.4.4.10	INTEGER	read-write	Enable/Disable the set point to trigger high warning alarm.
INT scSensor2HumidityHighCriticalStatus	1.3.6.1.4.1.534.6.7.1.1.4.4.4.11	INTEGER	read-write	Enable/Disable the set point to trigger high critical alarm.
scSensor2Alarm1	1.3.6.1.4.1.534.6.7.1.1.4.4.5
STR scSensor2Alarm1Name	1.3.6.1.4.1.534.6.7.1.1.4.4.5.1	DisplayString	read-write	The name of alarm-1.
INT scSensor2Alarm1State	1.3.6.1.4.1.534.6.7.1.1.4.4.5.2	INTEGER	read-write	Setup the signal type to trigger alarm.
INT scSensor2Alarm1Hysteresis	1.3.6.1.4.1.534.6.7.1.1.4.4.5.3	INTEGER	read-write	The set value to delay the alarm triggered when event occurs.
scSensor2Alarm2	1.3.6.1.4.1.534.6.7.1.1.4.4.6
STR scSensor2Alarm2Name	1.3.6.1.4.1.534.6.7.1.1.4.4.6.1	DisplayString	read-write	The name of alarm-1.
INT scSensor2Alarm2State	1.3.6.1.4.1.534.6.7.1.1.4.4.6.2	INTEGER	read-write	Setup the signal type to trigger alarm.
INT scSensor2Alarm2Hysteresis	1.3.6.1.4.1.534.6.7.1.1.4.4.6.3	INTEGER	read-write	The set value to delay the alarm triggered when event occurs.
rmTraps	1.3.6.1.4.1.534.6.7.1.2
NTF rmCommunicationRestored	1.3.6.1.4.1.534.6.7.1.2.0.1			INFORMATION: Communication between RackMonitor and sensor had established.
NTF rmCommunicationLost	1.3.6.1.4.1.534.6.7.1.2.0.2			WARNING: Communication between RackMonitor and sensor had lost.
NTF rmAlarm1Inactive	1.3.6.1.4.1.534.6.7.1.2.0.3			INFORMATION: Alarm1 of sensor had return from active state.
NTF rmAlarm1Active	1.3.6.1.4.1.534.6.7.1.2.0.4			WARNING: Alarm1 has become active.
NTF rmAlarm2Inactive	1.3.6.1.4.1.534.6.7.1.2.0.5			INFORMATION: Alarm2 of sensor has returned to normal state.
NTF rmAlarm2Active	1.3.6.1.4.1.534.6.7.1.2.0.6			WARNING: Alarm2 had became active.
NTF rmTemperatureNotHighWarning	1.3.6.1.4.1.534.6.7.1.2.0.7			INFORMATION: The temperature of sensor had return from High warning to normal.
NTF rmTemperatureHighWarning	1.3.6.1.4.1.534.6.7.1.2.0.8			WARNING: The temperature of sensor was higher than High warning set point.
NTF rmTemperatureNotLowWarning	1.3.6.1.4.1.534.6.7.1.2.0.9			INFORMATION: The temperature of sensor had return from low warning to normal.
NTF rmTemperatureLowWarning	1.3.6.1.4.1.534.6.7.1.2.0.10			WARNING: The temperature of sensor was lower than low warning set point.
NTF rmTemperatureNotHighCritical	1.3.6.1.4.1.534.6.7.1.2.0.11			INFORMATION: The temperature of sensor lower than high critical set point.
NTF rmTemperatureHighCritical	1.3.6.1.4.1.534.6.7.1.2.0.12			CRITICAL: The temperature of sensor was higher than high critical set point.
NTF rmTemperatureNotLowCritical	1.3.6.1.4.1.534.6.7.1.2.0.13			INFORMATION: The temperature of sensor was higher than low critical set point.
NTF rmTemperatureLowCritical	1.3.6.1.4.1.534.6.7.1.2.0.14			CRITICAL: The temperature of sensor was lower than low critical set point.
NTF rmHumidityNotHighWarning	1.3.6.1.4.1.534.6.7.1.2.0.15			INFORMATION: The humidity of sensor had return from High warning to normal.
NTF rmHumidityHighWarning	1.3.6.1.4.1.534.6.7.1.2.0.16			WARNING: The humidity of sensor was higher than High warning set point.
NTF rmHumidityNotLowWarning	1.3.6.1.4.1.534.6.7.1.2.0.17			INFORMATION: The humidity of sensor had return from low warning to normal.
NTF rmHumidityLowWarning	1.3.6.1.4.1.534.6.7.1.2.0.18			WARNING: The humidity of sensor was lower than low warning set point.
NTF rmHumidityNotHighCritical	1.3.6.1.4.1.534.6.7.1.2.0.19			INFORMATION: The humidity of sensor lower than high critical set point.
NTF rmHumidityHighCritical	1.3.6.1.4.1.534.6.7.1.2.0.20			CRITICAL: The humidity of sensor was higher than high critical set point.
NTF rmHumidityNotLowCritical	1.3.6.1.4.1.534.6.7.1.2.0.21			INFORMATION: The humidity of sensor was higher than low critical set point.
NTF rmHumidityLowCritical	1.3.6.1.4.1.534.6.7.1.2.0.22			CRITICAL: The humidity of sensor was lower than low critical set point.

RFC description

Monitors rack-mounted environmental conditions including temperature, humidity, power consumption, and door sensor status.

Start monitoring Eaton/Powerware Rack Monitor environmental monitoring appliances (temperature/humidity/alarm probes) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RackMonitor-MIB

What Is RackMonitor-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description