REDLINE-AN50-PMP-V1-MIB

All MIBs › REDLINE-AN50-PMP-V1-MIB

Category: Wireless and Radio

Description: Provides version 1 management objects for Redline AN50 point-to-multipoint WiMAX sector and subscriber unit control.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is REDLINE-AN50-PMP-V1-MIB?

REDLINE-AN50-PMP-V1-MIB is a vendor MIB from Redline Communications providing version-1 management objects for the AN50 point-to-multipoint (PMP) WiMAX base station, covering sector and subscriber-unit link control in fixed wireless broadband access networks. It exposes a link table describing each subscriber connection to the base station sector, including link identity, peer MAC address, and configured burst-rate/committed-information-rate parameters. Its data is used to monitor the operational status and configuration of each wireless subscriber link, verifying link presence via peer MAC visibility and bandwidth provisioning (max uplink/downlink burst rates, CIR/PIR), which helps diagnose subscriber connectivity loss or bandwidth misprovisioning on the sector. It is a self-contained Redline enterprise MIB with no strong dependency on external wireless standards MIBs. It is typically deployed by wireless ISPs operating Redline AN50 WiMAX base stations to manage point-to-multipoint subscriber connectivity, and the REDLINE-AN50-PMP-V1-MIB download lets administrators load it directly into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in REDLINE-AN50-PMP-V1-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Redline AN50 WiMAX base station (point-to-multipoint)

Monitoring Examples

An operator can poll the an50pmpLinkTable/an50pmpLinkEntry rows, each keyed by an50pmpLinkID, to see the an50pmpLinkPeerMac of every subscriber unit associated with a given an50pmpLinkGroupID (sector). Comparing configured an50pmpLinkMaxDLBurstRate/an50pmpLinkMaxULBurstRate and an50pmpLinkCIDDLCIR/an50pmpLinkCIDDLPIR values against actual observed link behavior confirms bandwidth is provisioned as expected for each subscriber. A subscriber link entry disappearing from the table, or an50pmpLinkMaxHost being exceeded, would indicate a lost connection or an over-subscribed sector.

What Can Be Monitored

subscriber link status
peer MAC address per link
downlink/uplink burst rate provisioning
CIR/PIR bandwidth settings
hosts per link

Imported Objects

From RFC1155-SMI

IpAddress
OBJECT-TYPE
TimeTicks
enterprises

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT an50pmpCIDSaveConfig	1.3.6.1.4.1.10728.2.51.3	INTEGER	read-write	The attribute saves the entire config set of the AN50 PMP.
OCT an50pmpLastDeniedSsMacAddress	1.3.6.1.4.1.10728.2.51.8	OCTET STRING	read-write	MAC address of the SS that will be denied by thisBS.
OCT an50pmpLastMissedSsMacAddress	1.3.6.1.4.1.10728.2.51.5	OCTET STRING	read-only	MAC address of the SS that missed the registration with the BS.
INT an50pmpLastModifiedCID	1.3.6.1.4.1.10728.2.51.4	INTEGER	read-only	The attribute represents the last modified CID.
OCT an50pmpLastRegisteredSsMacAddress	1.3.6.1.4.1.10728.2.51.6	OCTET STRING	read-only	MAC address of the last SS that successfuly registered with the BS.
INT an50pmpLastSuccessfulID	1.3.6.1.4.1.10728.2.51.7	INTEGER	read-only	The ID of the Link registered in BS table that is sent through LastSuccessfulRegisteredSS Trap(number10).
INT an50pmpLinkCIDDLCIR	1.3.6.1.4.1.10728.2.51.1.1.8	INTEGER	read-write	The downlink commited rate for this connection in kb/s.
INT an50pmpLinkCIDDLPIR	1.3.6.1.4.1.10728.2.51.1.1.9	INTEGER	read-write	The downlink peak rate for this connection in kb/s.
INT an50pmpLinkCIDULCIR	1.3.6.1.4.1.10728.2.51.1.1.10	INTEGER	read-write	The uplink commited rate for this connection in kb/s.
INT an50pmpLinkCIDULPIR	1.3.6.1.4.1.10728.2.51.1.1.11	INTEGER	read-write	The uplink peak rate for this connection in kb/s.
INT an50pmpLinkDLBurstRate	1.3.6.1.4.1.10728.2.51.2.1.5	INTEGER	read-only	Current master Tx burst rate. Rate range: 6Mb/s=1, 9Mb/s=2, 12Mb/s=3, 18Mb/s=4, 24Mb/s=5, 36Mb/s=6, 48Mb/s=7, 54Mbs=8.
INT an50pmpLinkDLCIDStatPktDisc	1.3.6.1.4.1.10728.2.51.2.1.12	INTEGER	read-only	Packets discarded by master due to buffer full.
INT an50pmpLinkDLCIDStatPktRecv	1.3.6.1.4.1.10728.2.51.2.1.14	INTEGER	read-only	Packets received by slave
INT an50pmpLinkDLCIDStatPktTran	1.3.6.1.4.1.10728.2.51.2.1.13	INTEGER	read-only	Packets transmitted from master to slave.
INT an50pmpLinkDLQoS	1.3.6.1.4.1.10728.2.51.1.1.12	INTEGER	read-write	The downlink QoS level.
INT an50pmpLinkDLRSSI	1.3.6.1.4.1.10728.2.51.2.1.6	INTEGER	read-only	RSSI (Received Signal Strength Indicator) at slave.
INT an50pmpLinkDLSINADR	1.3.6.1.4.1.10728.2.51.2.1.7	INTEGER	read-only	SINADR (Signal Interference and Noise Distorsion Ratio) at slave.
INT an50pmpLinkDLStatBlksDisc	1.3.6.1.4.1.10728.2.51.2.1.11	INTEGER	read-only	Blocks lost from master to slave
INT an50pmpLinkDLStatBlksRetr	1.3.6.1.4.1.10728.2.51.2.1.10	INTEGER	read-only	Block re-transmitted from master to slave.
INT an50pmpLinkDLStatBlksTot	1.3.6.1.4.1.10728.2.51.2.1.9	INTEGER	read-only	Blocks transmitted from master to slave.
INT an50pmpLinkDLStatLostFrm	1.3.6.1.4.1.10728.2.51.2.1.8	INTEGER	read-only	SINADR at slave.
an50pmpLinkEntry	1.3.6.1.4.1.10728.2.51.1.1		not-accessible	A unique set of link parameters.
INT an50pmpLinkGroupID	1.3.6.1.4.1.10728.2.51.1.1.3	INTEGER	read-write	Group assigned to this link.
INT an50pmpLinkID	1.3.6.1.4.1.10728.2.51.1.1.1	INTEGER	read-only	Link ID, a unique number between 1 and 1024 that identifies a particular link.
INT an50pmpLinkLostCount	1.3.6.1.4.1.10728.2.51.2.1.26	INTEGER	read-only	Number of times the link has been lost.
INT an50pmpLinkMaxDLBurstRate	1.3.6.1.4.1.10728.2.51.1.1.5	INTEGER	read-write	Maximum downlink rate for this link. Rate range: 6Mb/s=1, 9Mb/s=2, 12Mb/s=3, 18Mb/s=4, 24Mb/s=5, 36Mb/s=6, 48Mb/s=7, 54Mbs=8.
INT an50pmpLinkMaxHost	1.3.6.1.4.1.10728.2.51.1.1.7	INTEGER	read-write	Maximum number of hosts for this link.
INT an50pmpLinkMaxULBurstRate	1.3.6.1.4.1.10728.2.51.1.1.6	INTEGER	read-write	Maximum uplink rate for this link. Rate range: 6Mb/s=1, 9Mb/s=2, 12Mb/s=3, 18Mb/s=4, 24Mb/s=5, 36Mb/s=6, 48Mb/s=7, 54Mbs=8.
OCT an50pmpLinkName	1.3.6.1.4.1.10728.2.51.1.1.2	OCTET STRING	read-write	The name of the Link/Connection
OCT an50pmpLinkPeerMac	1.3.6.1.4.1.10728.2.51.1.1.4	OCTET STRING	read-write	Link Destination MAC address.
INT an50pmpLinkRegConn	1.3.6.1.4.1.10728.2.51.2.1.4	INTEGER	read-only	Number of connections configured for this link.
ROW an50pmpLinkRowStatus	1.3.6.1.4.1.10728.2.51.1.1.14	RowStatus	read-write	Status of the row
INT an50pmpLinkStatus	1.3.6.1.4.1.10728.2.51.2.1.2	INTEGER	read-only	Status of the Link.
INT an50pmpLinkStatusCode	1.3.6.1.4.1.10728.2.51.2.1.3	INTEGER	read-only	Alarm bits shown as a hex number.
an50pmpLinkStatusEntry	1.3.6.1.4.1.10728.2.51.2.1		not-accessible	Statistics for a link connection.
INT an50pmpLinkStatusID	1.3.6.1.4.1.10728.2.51.2.1.1	INTEGER	read-only	Index for an50pmpLinkStatusTable table
an50pmpLinkStatusTable	1.3.6.1.4.1.10728.2.51.2		not-accessible	Statistics per uplink connections.
an50pmpLinkTable	1.3.6.1.4.1.10728.2.51.1		not-accessible	Table with Wireless links and connections information configured into AN50 PMP device based on V1 processor.
INT an50pmpLinkULBurstRate	1.3.6.1.4.1.10728.2.51.2.1.15	INTEGER	read-only	Current Slave Tx Burst Rate. Rate range: 6Mb/s=1, 9Mb/s=2, 12Mb/s=3, 18Mb/s=4, 24Mb/s=5, 36Mb/s=6, 48Mb/s=7, 54Mbs=8.
INT an50pmpLinkULCIDStatPktDisc	1.3.6.1.4.1.10728.2.51.2.1.22	INTEGER	read-only	Packets discarded by slave due to buffer full.
INT an50pmpLinkULCIDStatPktRecv	1.3.6.1.4.1.10728.2.51.2.1.24	INTEGER	read-only	Packets received by master from slave.
INT an50pmpLinkULCIDStatPktTran	1.3.6.1.4.1.10728.2.51.2.1.23	INTEGER	read-only	Packets transmitted from slave to master.
INT an50pmpLinkULQoS	1.3.6.1.4.1.10728.2.51.1.1.13	INTEGER	read-write	The uplink QoS level.
INT an50pmpLinkULRSSI	1.3.6.1.4.1.10728.2.51.2.1.16	INTEGER	read-only	RSSI at master.
INT an50pmpLinkULSINADR	1.3.6.1.4.1.10728.2.51.2.1.17	INTEGER	read-only	SINADR at master.
INT an50pmpLinkULStatBlksDisc	1.3.6.1.4.1.10728.2.51.2.1.21	INTEGER	read-only	Blocks lost from slave to master.
INT an50pmpLinkULStatBlksRetr	1.3.6.1.4.1.10728.2.51.2.1.20	INTEGER	read-only	Block re-transmitted slave to master.
INT an50pmpLinkULStatBlksTot	1.3.6.1.4.1.10728.2.51.2.1.19	INTEGER	read-only	Blocks transmitted slave to master.
INT an50pmpLinkULStatLostFrm	1.3.6.1.4.1.10728.2.51.2.1.18	INTEGER	read-only	Frames lost from slave to master
TIK an50pmpLinkUpTime	1.3.6.1.4.1.10728.2.51.2.1.25	TimeTicks	read-only	Time since the link is UP (in hundreth a of second).
redline	1.3.6.1.4.1.10728
redlineAN50	1.3.6.1.4.1.10728.1.1
redlineAN50PMPV1	1.3.6.1.4.1.10728.2.51
redlineMgmt	1.3.6.1.4.1.10728.2
redlineProducts	1.3.6.1.4.1.10728.1

RFC description

Redline Communications SNMP MIB for managing AN-50 series wireless broadband equipment in Point-to-Multipoint (PMP) mode, supporting 5.5 GHz TDD operations.

Start monitoring Redline AN50 WiMAX base station, point-to-multipoint, V1 processor (subscriber link status/bandwidth) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download REDLINE-AN50-PMP-V1-MIB

What Is REDLINE-AN50-PMP-V1-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description