REDLINE-AN50-PMP-V2-MIB

MIB Reference — IPNetwork Monitor · Updated September 09, 2026

All MIBs › REDLINE-AN50-PMP-V2-MIB

Organization: Redline Communications, Inc.

Last Updated: 2005-03-16

Category: Wireless and Radio

Description: Provides version 2 management objects for Redline Communications AN50 point-to-multipoint WiMAX subscriber provisioning and statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is REDLINE-AN50-PMP-V2-MIB?

REDLINE-AN50-PMP-V2-MIB is a Redline Communications enterprise MIB for the AN-50 point-to-multipoint (PMP) WiMAX base station/subscriber system using the V2 processor hardware, which connects multiple subscriber stations to a central base station over fixed wireless links. It exposes per-link configuration and performance objects, including link identification, peer subscriber MAC address, group assignment, and quality-of-service parameters such as maximum burst rates and committed/peak information rates (CIR/PIR) per connection identifier (CID). Its monitoring focus centers on wireless link performance and subscriber connection status rather than general chassis hardware: an operator uses it to track how many subscriber links are active, their configured burst-rate limits, and per-CID bandwidth guarantees, which helps identify bandwidth contention or misconfigured subscriber service levels. It is a vendor-specific MIB not built directly on a common wireless standard MIB, reflecting Redline's proprietary V2 hardware/software stack. It is deployed on Redline AN-50 PMP base stations and subscriber units in fixed wireless broadband access networks, such as rural or enterprise WiMAX deployments, and operators typically open a REDLINE-AN50-PMP-V2-MIB MIB Browser session to review the per-link and per-CID objects during provisioning.

IPNetwork Monitor allows you to monitor SNMP objects defined in REDLINE-AN50-PMP-V2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

  • Redline AN-50 PMP WiMAX base stations
  • Redline AN-50 subscriber station units

Monitoring Examples

An operator would poll an50pmpLinkTable/an50pmpLinkEntry, keyed by an50pmpLinkID, to see each subscriber link's an50pmpLinkName, an50pmpLinkGroupId, and an50pmpLinkPeerMac. Comparing an50pmpLinkMaxDLBurstRate/an50pmpLinkMaxULBurstRate and an50pmpLinkCIDDLCIR/an50pmpLinkCIDDLPIR against actual observed throughput would reveal whether a subscriber is being rate-limited as configured or is failing to reach its committed rate due to RF conditions. A subscriber link missing from the table, or one with an unexpected an50pmpLinkMaxHost value, would indicate a provisioning or connectivity problem for that station.

What Can Be Monitored

  • per-subscriber link status and identity
  • configured max downlink/uplink burst rate
  • committed/peak information rate (CIR/PIR) per link
  • subscriber group assignment
  • peer MAC address per link

This MIB depends on

Related MIBs

Imported Objects

From REDLINE-MIB

redlineMgmtOBJECT-IDENTITY

From SNMPv2-CONF

OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

RowStatus

How to Use in IPNetwork Monitor

Example using an50pmpGroupStatusDLPacketsDiscards OID:

Select a Redline AN-50 PMP WiMAX base station/subscriber station, V2 processor (per-link QoS/bandwidth) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type an50pmpGroupStatusDLPacketsDiscards into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The packets discarded at master due to full buffer. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.
OIDs

RFC description

Wireless point-to-multipoint links and connections for Redline AN-50 PMP base station devices managing multiple subscriber stations.

Start monitoring Redline AN-50 PMP WiMAX base station/subscriber station, V2 processor (per-link QoS/bandwidth) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download REDLINE-AN50-PMP-V2-MIB