All MIBs › RADLAN-TRAPS-MIB
Organization: Marvell Semiconductor, Inc.
Last Updated: 2010-06-25
Category: System Management, Vendor: RADLAN/Cisco SB
Description:
Defines SNMP trap notifications for system events on Marvell/Radlan switch platforms.
Imported Objects
From RADLAN-BRIDGEMIBOBJECTS-MIB
| rldot1dStpTrapVrblVID | OBJECT-TYPE |
| rldot1dStpTrapVrblifIndex | OBJECT-TYPE |
| rndErrorDesc | OBJECT-TYPE |
| rndErrorSeverity | OBJECT-TYPE |
From RADLAN-MIB
| rnd | OBJECT-IDENTITY |
From SNMPv2-SMI
| NOTIFICATION-TYPE |
What Is RADLAN-TRAPS-MIB?
This is a Marvell/Radlan private MIB defining SNMP trap notifications for system-level events on switch platforms built on the Radlan embedded switch software stack, widely OEM'd by many switch vendors. Without sample objects available, its content is inferred to be primarily notification/trap definitions rather than a rich set of polled data objects, covering events such as system state changes, faults, or configuration events. Its monitoring value is in fault/event awareness—receiving asynchronous traps that flag hardware or software events (e.g., link state changes, power events, or system resets) as they happen rather than through periodic polling. It is part of Radlan's private enterprise MIB family, commonly used alongside other Radlan-based switch MIBs (interfaces, VLAN, etc.) on OEM switch platforms. It would be deployed on a wide range of OEM switches built on the Radlan/Marvell switch software stack across various vendors' branded products, and the RADLAN-TRAPS-MIB download is usually bundled with the vendor's switch firmware or management software package.
IPNetwork Monitor allows you to monitor SNMP objects defined in RADLAN-TRAPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
What Can Be Monitored
- system-level fault/event traps
Supported Devices
- OEM switches built on Marvell/Radlan switch software
Monitoring Examples
No sample objects were provided for this MIB, so specific trap names cannot be cited directly; however, based on its purpose, an NMS would typically register to receive traps from this MIB to be alerted in real time to system-level events such as a reboot, configuration change, or fault condition on a Radlan-based switch, rather than polling for them. Because trap MIBs are event-driven, the value here is immediate notification rather than periodic counter monitoring. Confirming exact trap object names would require consulting the actual MIB source.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| rndNotifications | 1.3.6.1.4.1.89.0 | This private MIB module defines Marvell's private notifications | ||
| NTF rxOverflowHWFault | 1.3.6.1.4.1.89.0.3 | An RX buffer overflow has occurred in one of the LAN or link interfaces. The bound variable rndErrorDesc provides the interface number. | ||
| NTF txOverflowHWFault | 1.3.6.1.4.1.89.0.4 | Interport queue overflow has occurred in one of the LAN or link interfaces. The bound variable rndErrorDesc provides the interface number. | ||
| NTF routeTableOverflow | 1.3.6.1.4.1.89.0.5 | An overflow condition has occurred in the Routing Table. The Routing Table is used for IP routing algorithm (RIP). | ||
| NTF resetRequired | 1.3.6.1.4.1.89.0.10 | This trap indicates that in order to perform the last SET request, a reset operation of the router/bridge is required. This occurs when the layer 2 routing algorithm is changed between SPF and Spanning Tree. The reset can be performed manually or using the variable rndAction. | ||
| NTF endTftp | 1.3.6.1.4.1.89.0.12 | This trap indicates that in the device finished a TFTP transaction with the management station. variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively. | ||
| NTF abortTftp | 1.3.6.1.4.1.89.0.13 | This trap indicates that in the device aborted a TFTP session with the management station. Variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively. | ||
| NTF startTftp | 1.3.6.1.4.1.89.0.14 | Informational trap indicating that the device has intiated a TFTP session. rndErrorDesc will contain the file type in question | ||
| NTF faultBackUp | 1.3.6.1.4.1.89.0.23 | Automantic switchover to backup link because of main link fault. | ||
| NTF mainLinkUp | 1.3.6.1.4.1.89.0.24 | Communication returened to main link. | ||
| NTF ipxRipTblOverflow | 1.3.6.1.4.1.89.0.36 | This trap indicates that in an OpenGate IPX RIP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively. | ||
| NTF ipxSapTblOverflow | 1.3.6.1.4.1.89.0.37 | This trap indicates that in an OpenGate IPX SAP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively. | ||
| NTF facsAccessVoilation | 1.3.6.1.4.1.89.0.49 | This trap indicates that message that fits FACS statenebt with operation blockAndReport was forward to the interface. The bound variable rndErrorDesc, rndErrorSeverity(== info ) and interface Number. | ||
| NTF autoConfigurationCompleted | 1.3.6.1.4.1.89.0.50 | This trap indicates that auto comfiguration completetd succssefully. The bound variable rndErrorDesc, rndErrorSeverity(== info ) | ||
| NTF forwardingTabOverflow | 1.3.6.1.4.1.89.0.51 | This trap indicates that an overflow condition has occurred in the layer II Forward Table. The bound variable rndErrorDesc, rndErrorSeverity(== warning ) | ||
| NTF framRelaySwitchConnectionUp | 1.3.6.1.4.1.89.0.53 | This trap indicates that a connection establish between the Frame relay Switch and the WanGate. The bound variable rndErrorDesc, rndErrorSeverity(== warning ) | ||
| NTF framRelaySwitchConnectionDown | 1.3.6.1.4.1.89.0.54 | This trap indicates that a connection between the Frame Relay Switch and the WanGate failed. The bound variable rndErrorDesc, rndErrorSeverity(== warning ) | ||
| NTF errorsDuringInit | 1.3.6.1.4.1.89.0.61 | This trap indicates that the an error occured during initialization The bound variable rndErrorDesc, rndErrorSeverity(== error ) | ||
| NTF vlanDynPortAdded | 1.3.6.1.4.1.89.0.66 | |||
| NTF vlanDynPortRemoved | 1.3.6.1.4.1.89.0.67 | |||
| NTF rsSDclientsTableOverflow | 1.3.6.1.4.1.89.0.68 | This warning is generated when an overflow occurs in the clients table. | ||
| NTF rsSDinactiveServer | 1.3.6.1.4.1.89.0.69 | This warning is generated when a server does not respond to the dispatchers polling and is thought to be inactive. | ||
| NTF rsIpZhrConnectionsTableOverflow | 1.3.6.1.4.1.89.0.70 | The Zero Hop Routing connections Table has been overflown. | ||
| NTF rsIpZhrReqStaticConnNotAccepted | 1.3.6.1.4.1.89.0.71 | The requested static connection was not accepted because there is no available IP virtual address to allocate to it. | ||
| NTF rsIpZhrVirtualIpAsSource | 1.3.6.1.4.1.89.0.72 | The virtual IP address appeared as a source IP. All the connections using it will be deleted and it will not be further allocated to new connections. | ||
| NTF rsIpZhrNotAllocVirtualIp | 1.3.6.1.4.1.89.0.73 | The source IP address sent an ARP specifying a virtual IP which was not allocated for this source. This virtual IP will not be allocated to connections of this specific source IP. | ||
| NTF rsSnmpSetRequestInSpecialCfgState | 1.3.6.1.4.1.89.0.74 | An incoming SNMP SET request was rejected because no such requests (except action requests) are accepted after start of new configuration reception or during sending the current configuration to an NMS. | ||
| NTF rsPingCompletion | 1.3.6.1.4.1.89.0.136 | A rsPingCompleted trap is sent at the completion of a sequence of pings if such a trap was requested when the sequence was initiated. The trap severity is info. The trap text will specify the following information: rsPingCompletionStatus, rsPingSentPackets, rsPingReceivedPackets In addition to the above listed objects (which are always present), the message will also specify the following quantities: if any responses were received: rsPingMinReturnTime rsPingAvgReturnTime rsPingMaxReturnTime | ||
| NTF pppSecurityViolation | 1.3.6.1.4.1.89.0.137 | This trap indicates that a PPP link got an unrecognized secret. The bound variables rndErrorDesc, rndErrorSeverity(== warning ), interface Number. and pppSecurityIdentity | ||
| NTF frDLCIStatudChange | 1.3.6.1.4.1.89.0.138 | |||
| NTF papFailedCommunication | 1.3.6.1.4.1.89.0.139 | |||
| NTF chapFailedCommunication | 1.3.6.1.4.1.89.0.140 | |||
| NTF rsWSDRedundancySwitch | 1.3.6.1.4.1.89.0.141 | Whenever main server fails and backup takes over or server comes up after failure a trap of this type is issued. | ||
| NTF rsDhcpAllocationFailure | 1.3.6.1.4.1.89.0.142 | DHCP failed to allocate an IP address to a requesting host because of memory shortage or inadequate configuration of available IP addresses. | ||
| NTF rlIpFftStnOverflow | 1.3.6.1.4.1.89.0.145 | The IP SFFT overflow. | ||
| NTF rlIpFftSubOverflow | 1.3.6.1.4.1.89.0.146 | The IP NFFT overflow. | ||
| NTF rlIpxFftStnOverflow | 1.3.6.1.4.1.89.0.147 | The IPX SFFT overflow. | ||
| NTF rlIpxFftSubOverflow | 1.3.6.1.4.1.89.0.148 | The IPX NFFT overflow. | ||
| NTF rlIpmFftOverflow | 1.3.6.1.4.1.89.0.149 | The IPM FFT overflow. | ||
| NTF rlPhysicalDescriptionChanged | 1.3.6.1.4.1.89.0.150 | Indicates that the physical decription of the device has changed | ||
| NTF rldot1dStpPortStateForwarding | 1.3.6.1.4.1.89.0.151 | The trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state. | ||
| NTF rldot1dStpPortStateNotForwarding | 1.3.6.1.4.1.89.0.152 | The trap is sent by a bridge when any of its configured ports transitions from the Forwarding state to the Blocking state. | ||
| NTF rlPolicyDropPacketTrap | 1.3.6.1.4.1.89.0.153 | Indicates that the packet drop due to the policy | ||
| NTF rlPolicyForwardPacketTrap | 1.3.6.1.4.1.89.0.154 | Indicates that the packet has forward based on policy | ||
| NTF rlIgmpProxyTableOverflow | 1.3.6.1.4.1.89.0.156 | An IGMP PROXY Table overflow. | ||
| NTF rlIgmpV1MsgReceived | 1.3.6.1.4.1.89.0.157 | An IGMP Message of v1 received on ifIndex. | ||
| NTF rlVrrpEntriesDeleted | 1.3.6.1.4.1.89.0.158 | One or more VRRP entries deleted due to IP interface deletion or transition. | ||
| NTF rlHotSwapTrap | 1.3.6.1.4.1.89.0.159 | Hot swap trap. | ||
| NTF rlTrunkPortAddedTrap | 1.3.6.1.4.1.89.0.160 | Informational trap indicating that a port is added to a trunk | ||
| NTF rlTrunkPortRemovedTrap | 1.3.6.1.4.1.89.0.161 | This warning is generated when a port removed from a trunk. | ||
| NTF rlTrunkPortNotCapableTrap | 1.3.6.1.4.1.89.0.162 | Informational trap indicating that a port can not be added to a trunk because of device limitations or diffrent swIfType. | ||
| NTF rlLockPortTrap | 1.3.6.1.4.1.89.0.170 | Informational trap indicating that a locked port receive a frame with new source Mac Address. | ||
| NTF vlanDynVlanAdded | 1.3.6.1.4.1.89.0.171 | add gvrp dynamic vlan | ||
| NTF vlanDynVlanRemoved | 1.3.6.1.4.1.89.0.172 | remove gvrp dynamic vlan | ||
| NTF vlanDynamicToStatic | 1.3.6.1.4.1.89.0.173 | vlan status was changed from dynamic to static | ||
| NTF vlanStaticToDynamic | 1.3.6.1.4.1.89.0.174 | vlan status was changed from static to dynamic | ||
| NTF dstrSysLog | 1.3.6.1.4.1.89.0.175 | Master receive trap from slave , and forward it as trap | ||
| NTF rlEnvMonFanStateChange | 1.3.6.1.4.1.89.0.176 | Trap indicating the fan state. rndErrorSeverity will be: 0 for fan state nomal, notPresent 1 for fan state warning, notFunctioning 2 for fan state critical 3 for fan state fatal The error text will specify the fan index, fan description and the exact fan state | ||
| NTF rlEnvMonPowerSupplyStateChange | 1.3.6.1.4.1.89.0.177 | Trap indicating the power supply state. rndErrorSeverity will be: 0 for power supply state nomal, notPresent 1 for power supply state warning, notFunctioning 2 for power supply state critical 3 for power supply state fatal The error text will specify the power supply index, power supply description and the exact power supply state | ||
| NTF rlStackStateChange | 1.3.6.1.4.1.89.0.178 | Trap indicating the stack connection state 0 for stack state connected, 1 for stack state disconnected | ||
| NTF rlEnvMonTemperatureRisingAlarm | 1.3.6.1.4.1.89.0.179 | Trap indicating that the temperature in the device has exceeded the device specific safe temperature threshold. | ||
| NTF rlBrgMacAddFailedTrap | 1.3.6.1.4.1.89.0.183 | Informational trap indicating that adding dynamic mac/s failed due to full hash chain. | ||
| NTF rldot1xPortStatusAuthorizedTrap | 1.3.6.1.4.1.89.0.184 | Informational trap indicating that port 802.1x status is authorized. | ||
| NTF rldot1xPortStatusUnauthorizedTrap | 1.3.6.1.4.1.89.0.185 | Warning trap is indicating that port 802.1x status is unAuthorized. | ||
| NTF swIfTablePortLock | 1.3.6.1.4.1.89.0.192 | Warning trap is indicating port lock hase began. | ||
| NTF swIfTablePortUnLock | 1.3.6.1.4.1.89.0.193 | Warning trap is indicating port lock has ended. | ||
| NTF rlAAAUserLocked | 1.3.6.1.4.1.89.0.194 | Warning trap indicating that the user was locked after number of consecutives unsuccessful login attempts. | ||
| NTF bpduGuardPortSuspended | 1.3.6.1.4.1.89.0.202 | Warning trap indicating - Port was suspended because there was BPDU Guard violation. | ||
| NTF rldot1xSupplicantMacAuthorizedTrap | 1.3.6.1.4.1.89.0.203 | Informational trap indicating that MAC authentication supplicant is authenticated and is allowed to access the network. | ||
| NTF rldot1xSupplicantMacUnauthorizedTrap | 1.3.6.1.4.1.89.0.204 | Warning trap is indicating that Radius server rejects MAC authentication supplicant. | ||
| NTF stpLoopbackDetection | 1.3.6.1.4.1.89.0.205 | Warning trap indicating - A loopback was detected on port. | ||
| NTF stpLoopbackDetectionResolved | 1.3.6.1.4.1.89.0.206 | Warning trap indicating - A loopback detection resolved on port. | ||
| NTF loopbackDetectionPortSuspended | 1.3.6.1.4.1.89.0.207 | Warning trap indicating - A port has been suspended by Loopback Detection. | ||
| NTF rlPortSuspended | 1.3.6.1.4.1.89.0.213 | Warning trap indicating - A port has been suspended by Any application. | ||
| NTF rlSpecialBpduDbOverflow | 1.3.6.1.4.1.89.0.214 | Warning trap indicating - Special BPDU DB Overflow. | ||
| NTF rldot1xSupplicantLoggedOutTrap | 1.3.6.1.4.1.89.0.215 | Warning trap is indicating that supplicant was logged out Since the port�s time-range state was changed to inactive. | ||
| NTF rldot1xPortControlModeNotAutoTrap | 1.3.6.1.4.1.89.0.216 | Warning trap is indicating that altough port�s time-range Is active now, it can not start working in mode auto. | ||
| NTF rlEeeLldpMultipleNeighbours | 1.3.6.1.4.1.89.0.217 | Warning trap indicating - Port has multiple LLDP remote link neighbours - EEE operational state will be FALSE. | ||
| NTF rlEeeLldpSingleNeighbour | 1.3.6.1.4.1.89.0.218 | Warning trap indicating - Port has single LLDP remote link neighbour - EEE operational can be TRUE. | ||
| NTF rldot1xSupplicantQuietPeriodTrap | 1.3.6.1.4.1.89.0.219 | Warning trap is indicating that supplicant quiet period timeout is active now. | ||
| NTF rlStackVersionUpgradeTrap | 1.3.6.1.4.1.89.0.222 | Informational trap indicating that stack slave is upgrading to the image or boot version of the stack master. | ||
| NTF rlStackVersionDowngradeTrap | 1.3.6.1.4.1.89.0.223 | Warning trap indicating that stack slave is downgrading to the image or boot version of the stack master. | ||
| NTF pseInrushPort | 1.3.6.1.4.1.89.0.240 | Informational trap indicating that port in PD does not meet the inrush-current standard. | ||
| NTF pseOverloadPort | 1.3.6.1.4.1.89.0.241 | Informational trap indicating that Port (x) requires more power than it should require. | ||
| NTF poePowerNegotiationInfo | 1.3.6.1.4.1.89.0.242 | Informational trap indicating power negotiation resolved power in Watts. | ||
| NTF poePowerNegotiation4Wire | 1.3.6.1.4.1.89.0.243 | Informational trap indicating power negotiation 4-Wire status. | ||
| NTF poePowerHWFail | 1.3.6.1.4.1.89.0.244 | Informational trap indicating power HW fail status. | ||
| NTF rlStormControlMinRateTrap | 1.3.6.1.4.1.89.0.246 | Warning trap indicating that port storm control rate limit is configured to minumum rate. | ||
| NTF rlApBackplanePortResolutionTrap | 1.3.6.1.4.1.89.0.247 | Informational trap indicating about backplane ethernet port resolution. | ||
| NTF sfpPortPresent | 1.3.6.1.4.1.89.0.248 | Informational trap indicating that gbic is now present on port (X). | ||
| NTF sfpPortNotPresent | 1.3.6.1.4.1.89.0.249 | Informational trap indicating that gbic is not present anymore on port (X). | ||
| NTF sfpPortLoss | 1.3.6.1.4.1.89.0.250 | Informational trap indicating that loss Diagnosed on port (X). | ||
| NTF sfpPortNotLoss | 1.3.6.1.4.1.89.0.251 | Informational trap indicating that loss isn't active anymore on port (X). | ||
| NTF rlStormControlOccursTrap | 1.3.6.1.4.1.89.0.252 | Warning trap indicating that port storm control occurs on a port. | ||
| NTF rlRadiusServTrapAcct | 1.3.6.1.4.1.89.0.255 | Radius server accounting event trap. | ||
| NTF rlRadiusServTrapAuthFailure | 1.3.6.1.4.1.89.0.256 | Radius server authentication failure event trap. | ||
| NTF rlRadiusServTrapAuthSuccess | 1.3.6.1.4.1.89.0.257 | Radius server authentication success event trap. |
RFC description
Defines enterprise-specific notifications and traps for Marvell/Radlan network devices including hardware faults and errors.
Start monitoring OEM switches built on Marvell/Radlan switch software (system-event trap notifications) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.