RADLAN-POLICY-MIB

All MIBs › RADLAN-POLICY-MIB

Organization: Radlan Computer Communications Ltd.

Last Updated: 2006-06-26

Category: QoS and Traffic Management, Vendor: RADLAN/Cisco SB

Description: Configures policy-based QoS rules for traffic classification and action assignment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RADLAN-POLICY-MIB?

RADLAN-POLICY-MIB originates from RADLAN Computer Communications, whose switch software/silicon stack underlies many OEM switch products (historically used by vendors such as Netgear and others), and it defines policy-based QoS traffic classification and action assignment. It exposes classifier configuration objects describing how many classification offsets are available, what operators are permitted for matching (OMPC criteria), and the actual classifier/rule definitions that map traffic patterns to actions. Its monitoring relevance is mainly configuration-state oriented: an administrator can verify which classification scheme and offset limits are in effect and audit the active policy rules and classifiers, rather than reading hardware environmental data, though misconfigured classifiers can directly explain unexpected QoS/traffic-handling behavior. It is a platform-level MIB tied to the RADLAN switch software stack and is used alongside standard QoS-related MIBs on switches built on that stack. It is deployed on OEM switches built on the RADLAN switching software/silicon platform, typically SMB-class managed Ethernet switches. Network engineers evaluating or troubleshooting this functionality can download the RADLAN-POLICY-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RADLAN-POLICY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

OEM switch built on RADLAN switching software/silicon platform

Monitoring Examples

An administrator would check rlPolicyMibVersion and rlPolicyFlowClassificationOffsetsGroupScheme to understand which classification scheme and version the switch is running, along with rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup and rlPolicyFlowClassificationOffsetGroupMaximumOffset to confirm classifier capacity limits. Walking rlPolicyClassifier and rlPolicyRules reveals the actual configured classification rules and their permitted operators via rlPolicyOMPCPermittedOperators. If traffic is not being classified as expected, comparing the active rlPolicyClassifier entries against rlPolicyClassifierPlatDependParams would reveal a rule exceeding platform-dependent limits or an unsupported offset configuration.

What Can Be Monitored

policy classifier configuration
classification offset scheme and limits
permitted OMPC operators
configured policy rules

Imported Objects

From DIFF-SERV-MIB

diffServClassifierEntry

OBJECT-TYPE

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From Q-BRIDGE-MIB

PortList
VlanId

From RADLAN-BRIDGEMIBOBJECTS-MIB

VlanList1
VlanList2
VlanList3
VlanList4

From RADLAN-MIB

Percents
VlanPriority
rnd	OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32
zeroDotZero

From SNMPv2-TC

DisplayString
RowPointer
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using rlPolicyRulesDroppedPackets OID:

Select an OEM switch built on RADLAN switching software/silicon platform (policy-based QoS classification) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type rlPolicyRulesDroppedPackets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of packets blocked by this filtering rule. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
rlPolicy	1.3.6.1.4.1.89.59			The private MIB module definition generic traffic policy in Radlan devices.
INT rlPolicyMibVersion	1.3.6.1.4.1.89.59.1	INTEGER	read-only	MIB's version, the current version is 14 1 - original version 2 - two new fields rlPolicyActionChangeDscpNonConform rlPolicyActionNewDscpNonConform were added. 3 - added support new policy features QoS modes: basic and advanced support for trusted mode operations mapping tables for trusted ports dscp, tcpUdp, mutation, remarking. 4 - I) added support to service mode. II)DSCP to VPT mapping table III) download marker 5 - Added cos-Dscp to RlPolicyTrustTypes 6 - Added rlPolicyFlowClassificationOffsetsGroupUseVPTId and rlPolicyFlowClassificationOffsetsGroupUseEtherTypeId To rlPolicyFlowClassificationOffsetsTable Added rlPolicyClassifierVPTID And rlPolicyClassifierEtherTypeID To rlPolicyClassifierTable Added Vpt and Ethertype support to rlPolicyClassifierAdditionalCriteriaSupported 7 - Added rlPolicyPortCfgPortRateLimitStatus,rlPolicyPortCfgCirPortRateLimit rlPolicyPortCfgCbsPortRateLimit to rlPolicyPortConfigurationTable 8 - Added rlPolicyDefaultForwardingProtocol to rlPolicyDefaultForwardingTable Added rlPolicyDscpToDpTable 9 - Add statistics 10 - Add classifier utilization 11 -Added rlPolicyFlowClassificationOffsetsGroupUseInnerVlanId To rlPolicyFlowClassificationOffsetsTable Added rlPolicyClassifierInnerVID To rlPolicyClassifierTable Added Inner vlan id support to rlPolicyClassifierAdditionalCriteriaSupported 12 - Added rlPolicyVlanConfigurationTable 13 - Added rlPolicyIsTCAvailable scalar 14 - Added rlPolicyCPUSafeGuardEnable
rlPolicyClassifier	1.3.6.1.4.1.89.59.2
rlPolicyClassifierPlatDependParams	1.3.6.1.4.1.89.59.2.1
INT rlPolicyFlowClassificationOffsetsGroupScheme	1.3.6.1.4.1.89.59.2.1.1	INTEGER	read-only	Some platforms allow Policy statements to examine all packet offsets(Opal); other platforms require specification of specific byte offsets for routedIp packets, another set of offsets for routedIpx, a third set for bridge.
INT rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup	1.3.6.1.4.1.89.59.2.1.2	INTEGER	read-only	For platforms which require an FCOG, indicates the maximum number of byte offsets specifiable for each offset group.
INT rlPolicyFlowClassificationOffsetGroupMaximumOffset	1.3.6.1.4.1.89.59.2.1.3	INTEGER	read-only	Indicates the maximum value of a byte offset in a Flow Classification Offset Group. If 0, there is no limit.
INT rlPolicyNumberOfOffsetsPerOmpcGroup	1.3.6.1.4.1.89.59.2.1.4	INTEGER	read-only	indicates the maximum number of byte offsets specifiable for each Ompc offset group.
INT rlPolicyOmpcMaximumOffset	1.3.6.1.4.1.89.59.2.1.5	INTEGER	read-only	Indicates the maximum value of a byte offset in a Ompc Group. If 0, there is no limit.
OCT rlPolicyOMPCPermittedOperators	1.3.6.1.4.1.89.59.2.1.6	OCTET STRING	read-only	A bit mask indicating which operators are permissable in an OMPC: ---------- \|87654321\| ---------- 1 - equal operator permitted 2 - not-equal operator permitted 3 - greater-than operator permitted 4 - less-than operator permitted
INT rlPolicyMaxOMPCLengthForBiggerSmallerOperation	1.3.6.1.4.1.89.59.2.1.7	INTEGER	read-only	Indicates the maximal permissible length of an OMPC using bigger' or 'smaller' condition. If 0, there is no limit.
OCT rlPolicyClassifierAdditionalCriteriaSupported	1.3.6.1.4.1.89.59.2.1.8	OCTET STRING	read-only	A bit mask indicating which additional Criteria may be supported by the classifier: ---------- \|87654321\| ---------- 1 - input port supported 2 - output port supported 3 - VLAN ID for bridging supported 4 - VPT ID for bridging supported 5 - EtherType ID for bridging supported 6 - Inner VLAN ID for bridging supported
T/F rlPolicyClassifierAdditionalCriteriaUsedInOffsetCount	1.3.6.1.4.1.89.59.2.1.9	TruthValue	read-only	Indicates whether the additional FCOG or Classifier criteria (ie. inPort, outPort VID count towards the maximum number of offsets ie. whether using inPort in the FCOG reduces the maximum number of offsets available.
OCT rlPolicyClassifierPermittedOffsetTypes	1.3.6.1.4.1.89.59.2.1.10	OCTET STRING	read-only	A bit mask indicating which offset types are supported by the platform for FCOG and OMPC definitions: ---------- \|87654321\| ---------- 1 - L2 offsets supported 2 - L3 offsets supported
OCT rlPolicyClassifierOMPCActions	1.3.6.1.4.1.89.59.2.1.11	OCTET STRING	read-only	A bit mask indicating which operation could be performed with OPMC ---------- \|87654321\| ---------- 1 - equal, 2 - notEqual, 3 - bigger, 4 - smaller.
rlPolicyFlowClassificationOffsetsTable	1.3.6.1.4.1.89.59.2.2		not-accessible	Specifies the byte offsets that the platform can use for policy decisions. This table is used for platforms which impose limitations on choosing the OMPCs for classification. If the platform does not impose any limitations, the value of rlPolicyFlowClassificationOffsetsGroupScheme is allOffsetsPermitted. Each entry in the table specifies a combination of byte offsets which can be used to specify flow classification. A rule may use a subset of the bytes of its Offset Group. The maximum value for each offset is given by rlPolicyFlowClassificationOffsetGroupMaximumOffset. The maximum number of offsets per Offset Group is given by rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup.
rlPolicyFlowClassificationOffsetsGroupEntry	1.3.6.1.4.1.89.59.2.2.1		not-accessible	The flow classification offset table entry includes the following parameters
RLP rlPolicyFlowClassificationOffsetsGroupType	1.3.6.1.4.1.89.59.2.2.1.1	RlPolicyGroupType	read-only	Specifies a classifier type for which offset bytes can be specified.
OID rlPolicyFlowClassificationOffsetsGroupOffset	1.3.6.1.4.1.89.59.2.2.1.2	OBJECT IDENTIFIER	read-write	The list of offsets to be included in the Flow Classification Offset Group are specified as subidentifiers in the OID(after the first 2 bytes which must be 1.1). The maximal number of permissible offsets is given by rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup. The maximal value that an offset can have is rlPolicyFlowClassificationOffsetGroupMaximumOffset.
OID rlPolicyFlowClassificationOffsetsGroupOffsetType	1.3.6.1.4.1.89.59.2.2.1.3	OBJECT IDENTIFIER	read-write	Indicates whether the corresponding byte denotes an offset from beginning of L2, from the beginning of L3 IPv4 packet data or from the beginning of L3 IPv6 packet data. Each byte in the OID contains either: (1) - L2 offset (2) - L3 Offset (3) - L3 IPv6 Offset
OCT rlPolicyFlowClassificationOffsetsGroupMask	1.3.6.1.4.1.89.59.2.2.1.4	OCTET STRING	read-write	The list of masks corresponding to the offsets to be included in the Flow Classification Offset Group are specified as bytes in the OID(after the first 2 bytes which must be 1.1).
T/F rlPolicyFlowClassificationOffsetsGroupUseInputInterface	1.3.6.1.4.1.89.59.2.2.1.5	TruthValue	read-write	Indicates whether or not the Input Interface Index is usable in Policy Rule definitions.
T/F rlPolicyFlowClassificationOffsetsGroupUseOutputInterface	1.3.6.1.4.1.89.59.2.2.1.6	TruthValue	read-write	Indicates whether or not the Output Interface Index(ie. routing/bridging decision) is usable in Policy Rule definitions
T/F rlPolicyFlowClassificationOffsetsGroupUseVlanId	1.3.6.1.4.1.89.59.2.2.1.7	TruthValue	read-write	Indicates whether or not the VlanId is usable in Policy Rule definitions for bridged packets
ROW rlPolicyFlowClassificationOffsetsGroupStatus	1.3.6.1.4.1.89.59.2.2.1.8	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table.
T/F rlPolicyFlowClassificationOffsetsGroupUseVPTId	1.3.6.1.4.1.89.59.2.2.1.9	TruthValue	read-write	Indicates whether or not the VPT is usable in Policy Rule definitions for bridged packets
T/F rlPolicyFlowClassificationOffsetsGroupUseEtherTypeId	1.3.6.1.4.1.89.59.2.2.1.10	TruthValue	read-write	Indicates whether or not the EtherType is usable in Policy Rule definitions for bridged packets
T/F rlPolicyFlowClassificationOffsetsGroupUseInnerVlanId	1.3.6.1.4.1.89.59.2.2.1.11	TruthValue	read-write	Indicates whether or not the inner VlanId is usable in Policy Rule definitions for bridged packets
rlPolicyOMPCTable	1.3.6.1.4.1.89.59.2.3		not-accessible	The table of OMPC statements.
rlPolicyOMPCEntry	1.3.6.1.4.1.89.59.2.3.1		not-accessible	Each classification statement consists of the following parameters
RLP rlPolicyOMPCGroupType	1.3.6.1.4.1.89.59.2.3.1.1	RlPolicyGroupType	read-only	Specifies a classifier type for which offset bytes can be specified.
INT rlPolicyOMPCIndex	1.3.6.1.4.1.89.59.2.3.1.2	INTEGER	read-only	Index into the OMPC Table.
INT rlPolicyOMPCOffset	1.3.6.1.4.1.89.59.2.3.1.3	INTEGER	read-write	Specifies the offset within the frame (in bytes) from the layer according to rlPolicyGroupType. The limitation of this field is according to the rlPolicyFlowClassificationOffsetGroupMaximumOffset parameter if this OMPC is used by an entry in the rlPolicyClassifierTable whose rlPolicyClassifierType is a protocol for which predefined offsets in rlPolicyFlowClassificationOffsetsTable are required. rlPolicyRequiredOffsetGroups indicates for which protocols there is such a requirement.
INT rlPolicyOMPCOffsetType	1.3.6.1.4.1.89.59.2.3.1.4	INTEGER	read-write	Indicates whether the offset should be interpreted as relative to the beginning of L2 or the beginning of L3
OCT rlPolicyOMPCMask	1.3.6.1.4.1.89.59.2.3.1.5	OCTET STRING	read-write	Specifies which bits of the rlPolicyOMPCPattern field are significant for packet comparison. The length of the mask, in case of 'bigger' or 'smaller' rlPolicyOMPCCondition, is limited by rlPolicyMaxOMPCLengthForBiggerSmallerOperation.
OCT rlPolicyOMPCPattern	1.3.6.1.4.1.89.59.2.3.1.6	OCTET STRING	read-write	Describes the mask field. The length of this object must be equal to the length of rlPolicyOMPCMask.
INT rlPolicyOMPCCondition	1.3.6.1.4.1.89.59.2.3.1.7	INTEGER	read-write	These define the operation carried out on the two 'operands' (frame and pattern), i.e. Bigger means that frame bits should be bigger than pattern bits. The permitted values are according to rlPolicyOMPCPermittedOperators parameter, if this OMPC is used by an entry in the rlPolicyClassifierTable whose rlPolicyClassifierType is a protocol for which predefined offsets in rlPolicyFlowClassificationOffsetsTable are required. rlPolicyRequiredOffsetGroups indicates for which protocols there is such a requirement.
STR rlPolicyOMPCDescription	1.3.6.1.4.1.89.59.2.3.1.8	DisplayString	read-write	Free text specifing the nature of this OMPC.
ROW rlPolicyOMPCStatus	1.3.6.1.4.1.89.59.2.3.1.9	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table.
rlPolicyClassifierTable	1.3.6.1.4.1.89.59.2.4		not-accessible	The table of Classifier statement.
rlPolicyClassifierEntry	1.3.6.1.4.1.89.59.2.4.1		not-accessible	Classifiers can be of the ingress, egress, or post-routing phase varieties. Each multifield classification statement consists of the following parameters.
RLP rlPolicyClassifierType	1.3.6.1.4.1.89.59.2.4.1.1	RlPolicyGroupType	read-only	Specifies a classifier type for which offset bytes can be specified.
INT rlPolicyClassifierListIndex	1.3.6.1.4.1.89.59.2.4.1.2	INTEGER	read-only	List Index into the Classifier Table.
INT rlPolicyClassifierSubListIndex	1.3.6.1.4.1.89.59.2.4.1.3	INTEGER	read-only	SubList Index into the Classifier Table.
INT rlPolicyClassifierIndex	1.3.6.1.4.1.89.59.2.4.1.4	INTEGER	read-only	Index into the Classifier Table.
OID rlPolicyClassifierOmpcList	1.3.6.1.4.1.89.59.2.4.1.5	OBJECT IDENTIFIER	read-write	The list of OMPCs to check with this Classifier. Each subidentifier together with rlPolicyClassifierType specify one OMPC.
NUM rlPolicyClassifierInIfIndex	1.3.6.1.4.1.89.59.2.4.1.6	InterfaceIndexOrZero	read-write	Input interface index to be compared with received packet, a value of 0 denotes that the classifier is applied to all ports.
NUM rlPolicyClassifierOutIfIndex	1.3.6.1.4.1.89.59.2.4.1.7	InterfaceIndexOrZero	read-write	Output interface index to be compared with sent packet, a value of 0 denotes that the classifier is applied to all ports.
INT rlPolicyClassifierVID	1.3.6.1.4.1.89.59.2.4.1.8	INTEGER	read-write	VLAN ID, used only for bridged traffic.
RLP rlPolicyClassifierDiffservInIfType	1.3.6.1.4.1.89.59.2.4.1.9	RlPolicyClassifierDiffservIfType	read-write	For a classifier used by the Diffserv Rules table. Enables specification of a classifier that should apply to all Diffserv boundary ports or all Diffserv Interior ports. If normal is specified, the rlPolicyClassifierInIfIndex field is used as it is in the non-diffserv case. If allBoundary or allInterior is selected, rlPolicyClassifierInIfIndex is ignored
RLP rlPolicyClassifierDiffservOutIfType	1.3.6.1.4.1.89.59.2.4.1.10	RlPolicyClassifierDiffservIfType	read-write	For a classifier used by the Diffserv Rules table. Enables specification of a classifier that should apply to outbound traffic on all Diffserv boundary ports or all Diffserv Interior ports. If normal is specified, the rlPolicyClassifierOutIfIndex field is used as it is in the non-diffserv case. If allBoundary or allInterior is selected, rlPolicyClassifierOutIfIndex is ignored
ROW rlPolicyClassifierStatus	1.3.6.1.4.1.89.59.2.4.1.11	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table.
POR rlPolicyClassifierInIfIndexList	1.3.6.1.4.1.89.59.2.4.1.12	PortList	read-write	allow to define list of ports for the specific classifier for ingress classification. if rlPolicyClassifierInIfIndex equal to zero then the following list should be reffered , if the list is empty we refer to ALL Ports
POR rlPolicyClassifierOutIfIndexList	1.3.6.1.4.1.89.59.2.4.1.13	PortList	read-write	allow to define list of ports for the specific classifier for egress classification. if rlPolicyClassifierOutIfIndex equal to zero then the following list should be reffered , if the list is empty we refer to ALL Ports
INT rlPolicyClassifierVPTID	1.3.6.1.4.1.89.59.2.4.1.14	INTEGER	read-write	VPT ID - user priority tag to be compared with . 8 is used to indicate not used value for this classifier
INT rlPolicyClassifierVPTIDMask	1.3.6.1.4.1.89.59.2.4.1.15	INTEGER	read-write	VPT ID Mask ,mask the user priority field . 0 is the default indicate Mask all compared with any VPT value
INT rlPolicyClassifierEtherTypeID	1.3.6.1.4.1.89.59.2.4.1.16	INTEGER	read-write	EtherType ID, to be compared with. 65535 is used to indicate not used value for this classifier 1499 is uded to indicate IPv4 ethertype that is originated from IPv4 ACL with permit/deny any any any 1500 is uded to indicate IPv6 ethertype that is originated from IPv6 ACL with permit/deny any any any
INT rlPolicyClassifierInnerVID	1.3.6.1.4.1.89.59.2.4.1.17	INTEGER	read-write	INNER VLAN ID, used only for double tagged traffic.
rlPolicyRules	1.3.6.1.4.1.89.59.3
rlPolicyRulesPlatDependParams	1.3.6.1.4.1.89.59.3.1
T/F rlPolicyDroppedPacketCountSupported	1.3.6.1.4.1.89.59.3.1.1	TruthValue	read-only	Indicates whether the dropped packets counter in the rlPolicyRulesTable is supported.
OCT rlPolicyFilterActionOptions	1.3.6.1.4.1.89.59.3.1.2	OCTET STRING	read-only	A bit mask indicating which operation could be perform ---------- \|87654321\| ---------- 1 - block, 2 - blockAndTrap, 3 - permitAndTrap, 4 - permit.
T/F rlPolicyIngressMeteringSupported	1.3.6.1.4.1.89.59.3.1.3	TruthValue	read-only	Specifies whether the platform supports metering in inbound packet rules.
T/F rlPolicyEgressMeteringSupported	1.3.6.1.4.1.89.59.3.1.4	TruthValue	read-only	Specifies whether the platform supports metering on outbound packet rules (for Diffserv).
rlPolicyRulesTable	1.3.6.1.4.1.89.59.3.2		not-accessible	The table of rules and Rules statements applied to all incoming traffic at the post-routing phase - ie. both the inPort and outPort are available for classification When Diffserv is not in effect(ie. IPX, bridging, or IP when the global option for Diffserv is off), certain table parameters are not available(see below). The DiffServ option is enabled or disabled by setting rlDiffservModeEnabled.
rlPolicyRulesEntry	1.3.6.1.4.1.89.59.3.2.1		not-accessible	Each multifield classification statement consists of the following parameters.
RLP rlPolicyRulesTableType	1.3.6.1.4.1.89.59.3.2.1.1	RlPolicyGroupType	read-only	Specifies a classifier type for which offset bytes can be specified.
INT rlPolicyRulesInterfaceDirection	1.3.6.1.4.1.89.59.3.2.1.2	INTEGER	read-only	Specifies the direction for this entry on the interface. 'inbound' traffic is operated on during receipt, while 'outbound' traffic is operated on prior to transmission. Based on the metering support: inbound available while the ingress metering supported, outbound available while egress metering supported, and none while no metering supported.
INT rlPolicyRulesListIndex	1.3.6.1.4.1.89.59.3.2.1.3	INTEGER	read-only	Enumerates the rule list entry.
INT rlPolicyRulesSubListIndex	1.3.6.1.4.1.89.59.3.2.1.4	INTEGER	read-only	Enumerates the rule sub-list entry.
INT rlPolicyRulesIndex	1.3.6.1.4.1.89.59.3.2.1.5	INTEGER	read-only	Enumerates the rule index entry.
INT rlPolicyRulesFilteringAction	1.3.6.1.4.1.89.59.3.2.1.6	INTEGER	read-write	Specifies the action for the filter. Values 1-10 reserved for the System filtering implemetation; Values starting from 11 may be used for user definition about future application.
C32 rlPolicyRulesDroppedPacketsEx	1.3.6.1.4.1.89.59.3.2.1.7	Counter32	read-only	The number of packets blocked by this filtering rule.
INT rlPolicyRulesFurtherRefPointer	1.3.6.1.4.1.89.59.3.2.1.8	INTEGER	read-write	This further reference indicate on the entry at the metering or action table, based on the supported features. The rlPolicyRulesFurtherRefPointer points on the metering table if the metering feature is supported, if not this fields points on the Action table
STR rlPolicyRulesDescription	1.3.6.1.4.1.89.59.3.2.1.9	DisplayString	read-write	Free text specifing the nature of this Rule.
ROW rlPolicyRulesStatus	1.3.6.1.4.1.89.59.3.2.1.10	RowStatus	read-write	Row status of the Rules entry.
INT rlPolicyRulesCounterIdx	1.3.6.1.4.1.89.59.3.2.1.11	INTEGER	read-write	If not zero, perform counting of matched packets .
C32 rlPolicyRulesCounter	1.3.6.1.4.1.89.59.3.2.1.12	Counter32	read-only	The number of packets that matched this filtering rule.
INT rlPolicyRulesActionPointer	1.3.6.1.4.1.89.59.3.2.1.13	INTEGER	read-write	This further reference indicate on the entry at the action table, The rlPolicyRulesActionPointer points on the action table if the aggregate metering feature is supported,or if meter is not belong to data path.
INT rlPolicyRulesTimeRange1	1.3.6.1.4.1.89.59.3.2.1.14	INTEGER	read-write	Time range of the first ACL.
INT rlPolicyRulesTimeRange2	1.3.6.1.4.1.89.59.3.2.1.15	INTEGER	read-write	Time range of the second ACL.
INT rlPolicyRulesSrcPortRangeStart	1.3.6.1.4.1.89.59.3.2.1.16	INTEGER	read-write	Start port of port range for source port.
INT rlPolicyRulesSrcPortRangeEnd	1.3.6.1.4.1.89.59.3.2.1.17	INTEGER	read-write	End port of port range for source port.
INT rlPolicyRulesDestPortRangeStart	1.3.6.1.4.1.89.59.3.2.1.18	INTEGER	read-write	Start port of port range for destination port.
INT rlPolicyRulesDestPortRangeEnd	1.3.6.1.4.1.89.59.3.2.1.19	INTEGER	read-write	End port of port range for destination port.
RLP rlPolicyRulesActionDropType	1.3.6.1.4.1.89.59.3.2.1.20	RlPolicyRulesActionDropType	read-write	This field is valid only if rlPolicyRulesFilteringAction is not permit. Used to distinguish between Hard and Soft drop.
INT rlPolicyRulesDownloadMarker	1.3.6.1.4.1.89.59.3.3	INTEGER	read-write	Indicates when rules download or removing starts and terminates.
rlPolicyMeterClass	1.3.6.1.4.1.89.59.4
rlPolicyMeterPlatDependParams	1.3.6.1.4.1.89.59.4.1
INT rlPolicyMeterDepth	1.3.6.1.4.1.89.59.4.1.1	INTEGER	read-only	Indicates how many meters can be chained in succession (ie. so that if the first meter fails, the second can be examined). The final meter in a sequence is always 'always-conform', so if the value of this parameter is 2, the platform that supports a single meter and then a second marking/action for meter failure.
rlPolicyMeterClassTable	1.3.6.1.4.1.89.59.4.2		not-accessible	This table defines the Metering classes for the system.
rlPolicyMeteringClassEntry	1.3.6.1.4.1.89.59.4.2.1		not-accessible	Each statement consists of the following parameters
INT rlPolicyMeteringClassIndex	1.3.6.1.4.1.89.59.4.2.1.1	INTEGER	read-only	This enumerates the table entry.
T/F rlPolicyMeteringClassAlwaysConform	1.3.6.1.4.1.89.59.4.2.1.2	TruthValue	read-write	If true, the meter always accepts all traffic; its rate is effectively infinite. In such a case, the token bucket defined by the MeterRate and Burst-Size parameters is ignored. also used when there isn't metering support.
INT rlPolicyMeteringClassAggregateMeterRate	1.3.6.1.4.1.89.59.4.2.1.3	INTEGER	read-write	The rate in kilobytes/second of traffic considered within the bandwidth allocated for this policy entry.
INT rlPolicyMeteringClassAggregateMeterBurstSize	1.3.6.1.4.1.89.59.4.2.1.4	INTEGER	read-write	The Burst Size parameter for the aggregate meter leaky bucket. A value of 0 means that the device should choose the Burst Size that it thinks is most suitable for the rule. The interval can be derived from (burstSizex8/Rate).
INT rlPolicyMeteringClassPerSessionMeteringRate	1.3.6.1.4.1.89.59.4.2.1.5	INTEGER	read-write	A Quantitative Appliction policy rule where each individual session requires a guaranteed minimum bandwidth. Specifies the Ingress traffic flow meter per session indicate a bandwidth limit to be applied to each individual session Value 0 at rlPolicyMeteringClassPerSessionMetering and rlPolicyMeteringClassMaxSessionLimit is interpreted to mean no sepecific requarment and the aggregate metering will be done by the system decision. The rate in kilobytes/second
INT rlPolicyMeteringClassMaxSessionLimit	1.3.6.1.4.1.89.59.4.2.1.6	INTEGER	read-write	indicate a the maximum number of session for a sepecific rule to guarante minimum bandwidth. Value 0 at rlPolicyMeteringClassPerSessionMetering and rlPolicyMeteringClassMaxSessionLimit is interpreted to mean no sepecific requarment and the aggregate metering will be done by the system decision.
INT rlPolicyMeteringClassActionPointer	1.3.6.1.4.1.89.59.4.2.1.7	INTEGER	read-write	Specifies the index in the rlPolicyActionTable to be accessed for packets that are in-profile. Value 0 is interpreted to mean no action. A non-zero value may be specified only for RoutedIp packets in Diffserv mode.
INT rlPolicyMeteringClassFailMeterPointer	1.3.6.1.4.1.89.59.4.2.1.8	INTEGER	read-write	Specifies an index in the rlPolicyMeterClassTable. This is the meter that is to be used if the packet is out-of-profile relative to the current meter. If non-Diffserv mode, this field is not used. If the current meter is AlwaysConform, this field is not used.
ROW rlPolicyMeteringClassStatus	1.3.6.1.4.1.89.59.4.2.1.9	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table.
T/F rlPolicyMeteringCounterEnable	1.3.6.1.4.1.89.59.4.2.1.10	TruthValue	read-write	Enable metering counter for the meter entry.
C32 rlPolicyMeteringClassInProfileCounter	1.3.6.1.4.1.89.59.4.2.1.11	Counter32	read-only	meter counter for packets that are in profile .
C32 rlPolicyMeteringClassOutProfileCounter	1.3.6.1.4.1.89.59.4.2.1.12	Counter32	read-only	meter counter for packets that are out of profile
rlPolicyAction	1.3.6.1.4.1.89.59.5
rlPolicyActionPlatDependParams	1.3.6.1.4.1.89.59.5.1
INT rlPolicyActionMREDSupported	1.3.6.1.4.1.89.59.5.1.1	INTEGER	read-only	Indicates whether the platform supports setting MRED characteristics in the packet action
T/F rlPolicyActionDroppedPacketCountSupported	1.3.6.1.4.1.89.59.5.1.2	TruthValue	read-only	Indicates whether the platform can maintain a count of packets Marked for drop by a particular action.
T/F rlPolicyActionDroppedDropPrecedenceSupported	1.3.6.1.4.1.89.59.5.1.3	TruthValue	read-only	Indicates whether the platform support at drop precedence.
OCT rlPolicyActionInProfileDropPrecedence	1.3.6.1.4.1.89.59.5.1.4	OCTET STRING	read-only	A bit mask indicating which drop precedence supported ---------- \|87654321\| ---------- 1 - low, 2 - medium, 3 - high, 4 - drop
OCT rlPolicyActionOutProfileDropPrecedence	1.3.6.1.4.1.89.59.5.1.5	OCTET STRING	read-only	A bit mask indicating which drop precedence supported ---------- \|87654321\| ---------- 1 - low, 2 - medium, 3 - high, 4 - drop
T/F rlPolicyActionDscpSupport	1.3.6.1.4.1.89.59.5.1.6	TruthValue	read-only	Indicates whether the platform support at DSCP filed modification.
INT rlPolicyActionDsQueueManagmentSupported	1.3.6.1.4.1.89.59.5.1.7	INTEGER	read-only	Indicates whether the platform supports at Q managment for implementation, mred, randomDrop used by the min/max threshold
rlPolicyActionTable	1.3.6.1.4.1.89.59.5.2		not-accessible	This table defines the Actions for packets that pass the meter table ie. the characteristics that are assigned to packets before they reach the scheduler. When Diffserv is not in effect(ie. IPX, bridging, or IP when the global option for Diffserv is off), certain table parameters are not available(see below). The DiffServ option is enabled or disabled by setting rlDiffservModeEnabled.
rlPolicyActionEntry	1.3.6.1.4.1.89.59.5.2.1		not-accessible	Each multifield classification statement consists of the following parameters
INT rlPolicyActionIndex	1.3.6.1.4.1.89.59.5.2.1.1	INTEGER	read-only	This enumerates the Action entry.
INT rlPolicyActionNewDscp	1.3.6.1.4.1.89.59.5.2.1.2	INTEGER	read-write	Indicates the new DSCP with which the packet should be marked
T/F rlPolicyActionChangeDscp	1.3.6.1.4.1.89.59.5.2.1.3	TruthValue	read-write	If true, the packet is re-marked with the value indicated by newDscp above. If false, the packet's DSCP value is not changed
INT rlPolicyActionMinThreshold	1.3.6.1.4.1.89.59.5.2.1.4	INTEGER	read-write	The min-threshold is the queue depth that a random drop process will seek to manage the queue's depth to. This object is in the action table rather than the queue table because Differentiated Services PHBs, such as the Assured Service, permit differently classified traffic to have different drop parameters even though they occupy the same queue.
INT rlPolicyActionMaxThreshold	1.3.6.1.4.1.89.59.5.2.1.5	INTEGER	read-write	The max-threshold is the maximum permissible queue depth. In tail drop scenarios, the queue will drop if a packet is presented to it and it is instantaneously full by this measure. In random drop scenarios, the queue will drop if a packet is presented to it and the average queue depth exceeds the max-threshold. This object is in the action table rather than the queue table because Differentiated Services PHBs, such as the Assured Service, permit differently classified traffic to have different drop parameters even though they occupy the same queue.
INT rlPolicyActionDropPolicy	1.3.6.1.4.1.89.59.5.2.1.6	INTEGER	read-write
C32 rlPolicyActionDroppedPackets	1.3.6.1.4.1.89.59.5.2.1.7	Counter32	read-only	The number of packets dropped by this action
INT rlPolicyActionNonDsInProfileDropPrecedence	1.3.6.1.4.1.89.59.5.2.1.8	INTEGER	read-write	This paramer is used at non diffserv mode to attached the drop precedence for packet InProfile (metering), only if there is a support for drop precedence and with what level.
INT rlPolicyActionNonDsOutProfileDropPrecedence	1.3.6.1.4.1.89.59.5.2.1.9	INTEGER	read-write	This paramer is used at non diffserv mode to attached the drop precedence for packet OutProfile (metering), only if there is a support for drop precedence and with what level.
T/F rlPolicyActionChangeVpt	1.3.6.1.4.1.89.59.5.2.1.10	TruthValue	read-write	Routed packets that run through the Rules receive VPT as define at the service class they attached to, bridge packets receive through the 802.1p operation unless we define to change the VPT for those packets.
INT rlPolicyActionNewVpt	1.3.6.1.4.1.89.59.5.2.1.11	INTEGER	read-write	Priority Tag that will be written to packets .
INT rlPolicyActionServiceClassPointer	1.3.6.1.4.1.89.59.5.2.1.12	INTEGER	read-write	Specifies the index in rlPolicyServiceClassTable denoting the service class to which the packet should be assigned after the action specified in this entry is carried out. A value of 0 means that no Service class is assigned. A value of 0 is legal only for routedIp packets in Diffserv mode on Inbound processing.
ROW rlPolicyActionStatus	1.3.6.1.4.1.89.59.5.2.1.13	RowStatus	read-write	The status of the table entry
T/F rlPolicyActionChangeDscpNonConform	1.3.6.1.4.1.89.59.5.2.1.14	TruthValue	read-write	If true, the packet is re-marked with the value indicated by newDscp for non conforming packets. If false, the packet's DSCP value is not changed
INT rlPolicyActionChangeNewDscpNonConform	1.3.6.1.4.1.89.59.5.2.1.15	INTEGER	read-write	Indicates the new DSCP with which the packet should be marked
T/F rlPolicyActionAdvancedTrustMode	1.3.6.1.4.1.89.59.5.2.1.16	TruthValue	read-write	Indicates if egress queue is assigned for packets match rule according to global trust mode or note.
INT rlPolicyActionNewIpPrecedence	1.3.6.1.4.1.89.59.5.2.1.17	INTEGER	read-write	Indicates the new Ip- Precedence with which the packet should be marked
T/F rlPolicyActionChangeIpPrecedence	1.3.6.1.4.1.89.59.5.2.1.18	TruthValue	read-write	If true, the packet is re-marked with the value indicated by newIpPrecedence above. If false, the packet's DSCP value is not changed
RLP rlPolicyActionReDirect	1.3.6.1.4.1.89.59.5.2.1.19	RlPolicyRedirectAction	read-write	Specified the redirection action/
NUM rlPolicyActionNewInterface	1.3.6.1.4.1.89.59.5.2.1.20	InterfaceIndexOrZero	read-write	Relevant if rlQosClassMapRedirect is either 'redirectToInterface' or 'analyzerPort'. Specified the output interface the packet is redireted to or the port that gets copy of the packet in addition to the port it was farwarded.
RLP rlPolicyActionChangeVidAction	1.3.6.1.4.1.89.59.5.2.1.21	RlPolicyMarkVlanAction	read-write	If 'mark', than the classified traffic will be remarked with new VLAN id. If 'disabled' VLAN id is not changed. If markNestedVlan, if the egress interface defined as VLAN tagged member then a new VLAN tag is added to the packet.
INT rlPolicyActionNewVid	1.3.6.1.4.1.89.59.5.2.1.22	INTEGER	read-write	If rlPolicyActionChangeVid is true, specify the new Vlan id to assigned to the packet
INT rlPolicyActionTrapTypeId	1.3.6.1.4.1.89.59.5.2.1.23	INTEGER	read-write	If now zero, Indicates the trap type id the matched packets arrives with, relevant when RedirectAction is trap or mirror.
U32 rlPolicyActionAddTunnel	1.3.6.1.4.1.89.59.5.2.1.24	Unsigned32	read-write	If not zero - Tunnel is added to matched packets.
rlPolicyServiceClass	1.3.6.1.4.1.89.59.6
rlPolicyServiceClassPlatDependParams	1.3.6.1.4.1.89.59.6.1
INT rlPolicyNumberOfServiceClassesSupported	1.3.6.1.4.1.89.59.6.1.1	INTEGER	read-only	Indicates the number of service classes supported on each port of the platform. Service classes can be neither created nor destroyed.
INT rlPolicyBoundedPriorityQueueSupport	1.3.6.1.4.1.89.59.6.1.2	INTEGER	read-only	Indicates whether the platform supports setting an upper limit to the bandwidth of traffic transmitted on queues operating in Strict Priority mode.
INT rlPolicyDefaultServiceClass	1.3.6.1.4.1.89.59.6.2	INTEGER	read-write	Indicates which service class is default one for packets whose COS is undetermined.
INT rlPolicyActiveServiceClassTable	1.3.6.1.4.1.89.59.6.3	INTEGER	read-write	Specifies the Service Class table preform active action (usuarlly after set of entries at the service class tentative table). Specifies the current status of a table, there could be two options, tentative/active table. only the tentative table is the read-write and the active table is read-only. at set to activeAction the tentative table will be copied to the active table.
rlPolicyServiceClassTentativeTable	1.3.6.1.4.1.89.59.6.4		not-accessible	This table defines the service classes for the system ie. the queue discipline and weight characteristics that are implemented on each port unless the user configures a port specific value in .... The total number of service classes defined can not exceed rlPolicyNumberOfTransmitQueuesPerPort.
rlPolicyServiceClassTentativeEntry	1.3.6.1.4.1.89.59.6.4.1		not-accessible	Each multifield classification statement consists of the following parameters
INT rlPolicyServiceClassTentativeIndex	1.3.6.1.4.1.89.59.6.4.1.1	INTEGER	read-only	This enumerates the ServiceClass Tentative entry.
STR rlPolicyServiceClassTentativeName	1.3.6.1.4.1.89.59.6.4.1.2	DisplayString	read-write	The name given by the system administrator to the class.
INT rlPolicyServiceClassTentativePhbType	1.3.6.1.4.1.89.59.6.4.1.3	INTEGER	read-write	Indicates the type of Diffserv per-hop behaviour that this service class is intended to support. This object can be set by the user only in DiffServ mode (i.e. rlDiffservModeEnabled = enabled).
INT rlPolicyServiceClassTentativeMinRate	1.3.6.1.4.1.89.59.6.4.1.4	INTEGER	read-write	Specifies either the minimum throughput of the queue as a percentage of the throughput of each output port on which the service class is implemented. If zero, there is no minimum rate. This field can not be set by the user if rlDiffservModeEnabled = disabled and rlPolicyServiceClassPriority > 0 or rlDiffservModeEnabled = enabled and rlPolicyServiceClassPhbType = expeditedForwarding.
INT rlPolicyServiceClassTentativeMaxRate	1.3.6.1.4.1.89.59.6.4.1.5	INTEGER	read-write	Specifies either the upper limit on the throughput of the queue as a percentage of the throughput of each output port on which the service class is implemented. If zero, there is no maximum rate. This field can not be set by the user if rlDiffservModeEnabled = disabled and rlPolicyServiceClassPriority = 0 or rlDiffservModeEnabled = enabled and rlPolicyServiceClassPhbType != expeditedForwarding or rlBoundedPriorityQueueSupport = notSupported.
INT rlPolicyServiceClassTentativePriority	1.3.6.1.4.1.89.59.6.4.1.6	INTEGER	read-write	If non-zero, this service class will operate as a priority service class with the specified priority value. This object can not be set in Diffserv mode (i.e. rlDiffservModeEnabled = enabled), in which case rlServiceClassPhbType should be used instead. It can't be set when rlBoundedPriorityQueueSupport = notSupported as well.
INT rlPolicyServiceClassTentative8021DPri	1.3.6.1.4.1.89.59.6.4.1.7	INTEGER	read-write	802.1D Priority Tag that will be written to routed packets and untagged bridged packets transmitted with this service class.
ROW rlPolicyServiceClassTentativeStatus	1.3.6.1.4.1.89.59.6.4.1.8	RowStatus	read-write	Status of this entry.
INT rlPolicyServiceClassTentativeTdThersholdDp0	1.3.6.1.4.1.89.59.6.4.1.9	INTEGER	read-write	Tail Drop Threshold for Drop Precedence 0. UNITS percent 0-100
INT rlPolicyServiceClassTentativeTdThersholdDp1	1.3.6.1.4.1.89.59.6.4.1.10	INTEGER	read-write	Tail Drop Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyServiceClassTentativeTdThersholdDp2	1.3.6.1.4.1.89.59.6.4.1.11	INTEGER	read-write	Tail Drop Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyServiceClassTentativeRedMinDp0	1.3.6.1.4.1.89.59.6.4.1.12	INTEGER	read-write	WRED Min Threshold for Drop Precedence 0. UNITS percent 0-100
INT rlPolicyServiceClassTentativeRedMaxDp0	1.3.6.1.4.1.89.59.6.4.1.13	INTEGER	read-write	WRED Max Threshold for Drop Precedence 0. UNITS percent 0-100
INT rlPolicyServiceClassTentativeRedProbDp0	1.3.6.1.4.1.89.59.6.4.1.14	INTEGER	read-write	WRED probability for Drop Precedence 0.
INT rlPolicyServiceClassTentativeRedMinDp1	1.3.6.1.4.1.89.59.6.4.1.15	INTEGER	read-write	WRED Min Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyServiceClassTentativeRedMaxDp1	1.3.6.1.4.1.89.59.6.4.1.16	INTEGER	read-write	WRED Max Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyServiceClassTentativeRedProbDp1	1.3.6.1.4.1.89.59.6.4.1.17	INTEGER	read-write	WRED probability for Drop Precedence 1.
INT rlPolicyServiceClassTentativeRedMinDp2	1.3.6.1.4.1.89.59.6.4.1.18	INTEGER	read-write	WRED Min Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyServiceClassTentativeRedMaxDp2	1.3.6.1.4.1.89.59.6.4.1.19	INTEGER	read-write	WRED Max Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyServiceClassTentativeRedProbDp2	1.3.6.1.4.1.89.59.6.4.1.20	INTEGER	read-write	WRED probability for Drop Precedence 2.
INT rlPolicyServiceClassTentativeRedQweight	1.3.6.1.4.1.89.59.6.4.1.21	INTEGER	read-write	additional parameter for the WRED algorithem supporting the Queue weight exponentail factor
T/F rlPolicyServiceClassTentativeShaperStatus	1.3.6.1.4.1.89.59.6.4.1.22	TruthValue	read-write	If there is shaper on the Queue
INT rlPolicyServiceClassTentativeCirQueueShaper	1.3.6.1.4.1.89.59.6.4.1.23	INTEGER	read-write	The CIR for the Queue shaper. N/A when the shper is disabled. UNITS bps bits per second
INT rlPolicyServiceClassTentativeCbsQueueShaper	1.3.6.1.4.1.89.59.6.4.1.24	INTEGER	read-write	The CBS for the Queue shaper. N/A when the shper is disabled. UNITS bytes
rlPolicyServiceClassActiveTable	1.3.6.1.4.1.89.59.6.5		not-accessible	This table defines the service classes for the system ie. the queue discipline and weight characteristics that are implemented on each port unless the user configures a port specific value in .... The total number of service classes defined can not exceed rlPolicyNumberOfTransmitQueuesPerPort.
rlPolicyServiceClassActiveEntry	1.3.6.1.4.1.89.59.6.5.1		not-accessible	Each multifield classification statement consists of the following parameters
INT rlPolicyServiceClassActiveIndex	1.3.6.1.4.1.89.59.6.5.1.1	INTEGER	read-only	This enumerates the ServiceClass Active entry.
STR rlPolicyServiceClassActiveName	1.3.6.1.4.1.89.59.6.5.1.2	DisplayString	read-only	The name given by the system administrator to the class.
INT rlPolicyServiceClassActivePhbType	1.3.6.1.4.1.89.59.6.5.1.3	INTEGER	read-only	Indicates the type of Diffserv per-hop behaviour that this service class is intended to support. This object can be set by the user only in DiffServ mode (i.e. rlDiffservModeEnabled = enabled).
INT rlPolicyServiceClassActiveMinRate	1.3.6.1.4.1.89.59.6.5.1.4	INTEGER	read-only	Specifies either the minimum throughput of the queue as a percentage of the throughput of each output port on which the service class is implemented. If zero, there is no minimum rate. This field can not be set by the user if rlDiffservModeEnabled = disabled and rlPolicyServiceClassPriority > 0 or rlDiffservModeEnabled = enabled and rlPolicyServiceClassPhbType = expeditedForwarding.
INT rlPolicyServiceClassActiveMaxRate	1.3.6.1.4.1.89.59.6.5.1.5	INTEGER	read-only	Specifies either the upper limit on the throughput of the queue as a percentage of the throughput of each output port on which the service class is implemented. If zero, there is no maximum rate. This field can not be set by the user if rlDiffservModeEnabled = disabled and rlPolicyServiceClassPriority = 0 or rlDiffservModeEnabled = enabled and rlPolicyServiceClassPhbType != expeditedForwarding or rlBoundedPriorityQueueSupport = notSupported.
INT rlPolicyServiceClassActivePriority	1.3.6.1.4.1.89.59.6.5.1.6	INTEGER	read-only	If non-zero, this service class will operate as a priority service class with the specified priority value. This object can not be set in Diffserv mode (i.e. rlDiffservModeEnabled = enabled), in which case rlServiceClassPhbType should be used instead. It can't be set when rlBoundedPriorityQueueSupport = notSupported as well.
INT rlPolicyServiceClassActive8021DPri	1.3.6.1.4.1.89.59.6.5.1.7	INTEGER	read-only	802.1D Priority Tag that will be written to routed packets and untagged bridged packets transmitted with this service class.
INT rlPolicyServiceClassActiveTdThersholdDp0	1.3.6.1.4.1.89.59.6.5.1.8	INTEGER	read-only	Tail Drop Threshold for Drop Precedence 0. UNITS percent 0-100
INT rlPolicyServiceClassActiveTdThersholdDp1	1.3.6.1.4.1.89.59.6.5.1.9	INTEGER	read-only	Tail Drop Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyServiceClassActiveTdThersholdDp2	1.3.6.1.4.1.89.59.6.5.1.10	INTEGER	read-only	Tail Drop Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyServiceClassActiveRedMinDp0	1.3.6.1.4.1.89.59.6.5.1.11	INTEGER	read-only	WRED Min Threshold for Drop Precedence 0. UNITS percent 0-100
INT rlPolicyServiceClassActiveRedMaxDp0	1.3.6.1.4.1.89.59.6.5.1.12	INTEGER	read-only	WRED Max Threshold for Drop Precedence 0. UNITS percent 0-100
INT rlPolicyServiceClassActiveRedProbDp0	1.3.6.1.4.1.89.59.6.5.1.13	INTEGER	read-only	WRED probability for Drop Precedence 0.
INT rlPolicyServiceClassActiveRedMinDp1	1.3.6.1.4.1.89.59.6.5.1.14	INTEGER	read-only	WRED Min Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyServiceClassActiveRedMaxDp1	1.3.6.1.4.1.89.59.6.5.1.15	INTEGER	read-only	WRED Max Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyServiceClassActiveRedProbDp1	1.3.6.1.4.1.89.59.6.5.1.16	INTEGER	read-only	WRED probability for Drop Precedence 1.
INT rlPolicyServiceClassActiveRedMinDp2	1.3.6.1.4.1.89.59.6.5.1.17	INTEGER	read-only	WRED Min Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyServiceClassActiveRedMaxDp2	1.3.6.1.4.1.89.59.6.5.1.18	INTEGER	read-only	WRED Max Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyServiceClassActiveRedProbDp2	1.3.6.1.4.1.89.59.6.5.1.19	INTEGER	read-only	WRED probability for Drop Precedence 2.
INT rlPolicyServiceClassActiveRedQweight	1.3.6.1.4.1.89.59.6.5.1.20	INTEGER	read-only	additional parameter for the WRED algorithem supporting the Queue weight exponentail factor
T/F rlPolicyServiceClassActiveShaperStatus	1.3.6.1.4.1.89.59.6.5.1.21	TruthValue	read-only	If there is shaper on the Queue
INT rlPolicyServiceClassActiveCirQueueShaper	1.3.6.1.4.1.89.59.6.5.1.22	INTEGER	read-only	The CIR for the queue shaper. N/A when the shper is disabled UNITS bps bits per second
INT rlPolicyServiceClassActiveCbsQueueShaper	1.3.6.1.4.1.89.59.6.5.1.23	INTEGER	read-only	The CBS for the queue shaper. N/A when the shper is disabled. UNITS bytes
rlPolicyPortConfigurationTable	1.3.6.1.4.1.89.59.6.6		not-accessible	This table enables the network administrator to fine-tune the bandwidth given to each service class on each port. The values in this table will thus override those of the rlServiceClassTable (THIS TABLE IS MANAGE FROM 3SW).
rlPolicyPortCfgEntry	1.3.6.1.4.1.89.59.6.6.1		not-accessible	Configuration parameters for each port/service class.
NUM rlPolicyPortCfgIfIndex	1.3.6.1.4.1.89.59.6.6.1.1	InterfaceIndex	read-only	Interface index.
OID rlPolicyPortCfgMinimalBandwidth	1.3.6.1.4.1.89.59.6.6.1.2	OBJECT IDENTIFIER	read-write	The list of objects contain parameters at Precents type for the minimal bandwidth to this port/service class at WWR . The OID length is based on the number of the service class number, every OID define parameter of service class.
OID rlPolicyPortCfgMaximalBandwidth	1.3.6.1.4.1.89.59.6.6.1.3	OBJECT IDENTIFIER	read-write	The list of objects contain parameters at Precents type for the maximal bandwidth to this port/service class at SP . The OID length is based on the number of the service class number, every OID define parameter of service class.
ROW rlPolicyPortCfgStatus	1.3.6.1.4.1.89.59.6.6.1.4	RowStatus	read-write	Status of this entry.
INT rlpolicyDropProfilePointer	1.3.6.1.4.1.89.59.6.6.1.5	INTEGER	read-write	pointing to drop algorithem profile. the profile describs the drop algorithem (tail, red)and params
OID rlPolicyPortCfgQueueShaperStatus	1.3.6.1.4.1.89.59.6.6.1.6	OBJECT IDENTIFIER	read-write	If there is shaper on the Queue
OID rlPolicyPortCfgCirQueueShaper	1.3.6.1.4.1.89.59.6.6.1.7	OBJECT IDENTIFIER	read-write	The CIR for the Queue shaper. N/A when the shper is disabled UNITS bps bits per second
OID rlPolicyPortCfgCbsQueueShaper	1.3.6.1.4.1.89.59.6.6.1.8	OBJECT IDENTIFIER	read-write	The CBS for the Queue shaper. N/A when the shper is disabled. UNITS bytes
T/F rlPolicyPortCfgPortShaperStatus	1.3.6.1.4.1.89.59.6.6.1.9	TruthValue	read-write	If there is shaper on the port
INT rlPolicyPortCfgCirPortShaper	1.3.6.1.4.1.89.59.6.6.1.10	INTEGER	read-write	The CIR for the port shaper. N/A when the shper is disabled UNITS bps bits per second
INT rlPolicyPortCfgCbsPortShaper	1.3.6.1.4.1.89.59.6.6.1.11	INTEGER	read-write	The CBS for the port shaper. N/A when the shper is disabled. UNITS bytes
T/F rlPolicyPortCfgPortRateLimitStatus	1.3.6.1.4.1.89.59.6.6.1.12	TruthValue	read-write	If there is Rate Limit on the port
INT rlPolicyPortCfgCirPortRateLimit	1.3.6.1.4.1.89.59.6.6.1.13	INTEGER	read-write	The CIR for the port Rate limit. N/A when the Rate limit is disabled UNITS bps bits per second
INT rlPolicyPortCfgCbsPortRateLimit	1.3.6.1.4.1.89.59.6.6.1.14	INTEGER	read-write	The CBS for the port Rate Limit. N/A when the Rate Limit is disabled. UNITS bytes
rlPolicyDropProfileTable	1.3.6.1.4.1.89.59.6.7		not-accessible	this table defines drop profile which describ the queue's drop algorithems
rlPolicyDropProfileEntry	1.3.6.1.4.1.89.59.6.7.1		not-accessible	Configuration parameters for each port/service class.
INT rlPolicyDropProfileIndex	1.3.6.1.4.1.89.59.6.7.1.1	INTEGER	read-only	Interface index.
INT rlPolicyDropProfileQueueNumber	1.3.6.1.4.1.89.59.6.7.1.2	INTEGER	read-only	Interface Queue number.
INT rlPolicyDropProfileTdThersholdDp0	1.3.6.1.4.1.89.59.6.7.1.3	INTEGER	read-write	Tail Drop Threshold for Drop Precedence 0. UNITS percent 0-100
INT rlPolicyDropProfileTdThersholdDp1	1.3.6.1.4.1.89.59.6.7.1.4	INTEGER	read-write	Tail Drop Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyDropProfileTdThersholdDp2	1.3.6.1.4.1.89.59.6.7.1.5	INTEGER	read-write	Tail Drop Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyDropProfileRedMinDp0	1.3.6.1.4.1.89.59.6.7.1.6	INTEGER	read-write	WRED Min Threshold for Drop Precedence 0. UNITS percent 0-100
INT rlPolicyDropProfileRedMaxDp0	1.3.6.1.4.1.89.59.6.7.1.7	INTEGER	read-write	WRED Max Threshold for Drop Precedence 0. UNITS percent 0-100 0-100
INT rlPolicyDropProfileRedProbDp0	1.3.6.1.4.1.89.59.6.7.1.8	INTEGER	read-write	WRED probability for Drop Precedence 0.
INT rlPolicyDropProfileRedMinDp1	1.3.6.1.4.1.89.59.6.7.1.9	INTEGER	read-write	WRED Min Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyDropProfileRedMaxDp1	1.3.6.1.4.1.89.59.6.7.1.10	INTEGER	read-write	WRED Max Threshold for Drop Precedence 1. UNITS percent 0-100
INT rlPolicyDropProfileRedProbDp1	1.3.6.1.4.1.89.59.6.7.1.11	INTEGER	read-write	WRED probability for Drop Precedence 1.
INT rlPolicyDropProfileRedMinDp2	1.3.6.1.4.1.89.59.6.7.1.12	INTEGER	read-write	WRED Min Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyDropProfileRedMaxDp2	1.3.6.1.4.1.89.59.6.7.1.13	INTEGER	read-write	WRED Max Threshold for Drop Precedence 2. UNITS percent 0-100
INT rlPolicyDropProfileRedProbDp2	1.3.6.1.4.1.89.59.6.7.1.14	INTEGER	read-write	WRED probability for Drop Precedence 2.
INT rlPolicyDropProfileRedQweight	1.3.6.1.4.1.89.59.6.7.1.15	INTEGER	read-write	additional parameter for the WRED algorithem supporting the Queue weight exponentail factor
ROW rlPolicyDropProfileStatus	1.3.6.1.4.1.89.59.6.7.1.16	RowStatus	read-write	Status of this entry.
rlPolicyVlanConfigurationTable	1.3.6.1.4.1.89.59.6.8		not-accessible	This table enables the network administrator to fine-tune the rate limit given to each vlan. The values in this table will thus override those of the rlQosIfPolicyTable (THIS TABLE IS MANAGED FROM 3SW).
rlPolicyVlanCfgEntry	1.3.6.1.4.1.89.59.6.8.1		not-accessible	Configuration parameters for each vlan.
VLA rlPolicyVlanCfgVlanId	1.3.6.1.4.1.89.59.6.8.1.1	VlanId	read-only	Interface index.
T/F rlPolicyVlanCfgPortRateLimitStatus	1.3.6.1.4.1.89.59.6.8.1.2	TruthValue	read-write	If there is Rate Limit on the vlan
INT rlPolicyVlanCfgCirPortRateLimit	1.3.6.1.4.1.89.59.6.8.1.3	INTEGER	read-write	The CIR for the port Rate limit. N/A when the Rate limit is disabled UNITS bps bits per second
INT rlPolicyVlanCfgCbsPortRateLimit	1.3.6.1.4.1.89.59.6.8.1.4	INTEGER	read-write	The CBS for the port Rate Limit. N/A when the Rate Limit is disabled. UNITS bytes
ROW rlPolicyVlanCfgStatus	1.3.6.1.4.1.89.59.6.8.1.5	RowStatus	read-write	Status of this entry.
rlPolicyDiffServ	1.3.6.1.4.1.89.59.7
rlPolicyDiffServPlatDependParams	1.3.6.1.4.1.89.59.7.1
INT rlDiffservModeSupported	1.3.6.1.4.1.89.59.7.1.1	INTEGER	read-only	Indicates whether Diffserv mode is supported on the platform.
INT rlDiffservModeEnabled	1.3.6.1.4.1.89.59.7.2	INTEGER	read-write	Indicates whether Diffserv mode is currently enabled.
rlDiffservBoundaryTable	1.3.6.1.4.1.89.59.7.3		not-accessible	Indicates whether a port is considered a boundary or an interior node of the Diffserv domain
rlDiffservBoundaryEntry	1.3.6.1.4.1.89.59.7.3.1		not-accessible	Each boundary/interior ports table entry consists of the following parameters
INT rlDiffservBoundaryIfIndex	1.3.6.1.4.1.89.59.7.3.1.1	INTEGER	read-only	The Interface index whose type is being defined
INT rlDiffservBoundaryPortType	1.3.6.1.4.1.89.59.7.3.1.2	INTEGER	read-write	The boundary status of the port.
ROW rlDiffservBoundaryStatus	1.3.6.1.4.1.89.59.7.3.1.3	RowStatus	read-write	Status of this entry.
rlPolicyGlobalParams	1.3.6.1.4.1.89.59.9
INT rlPolicyGlobalOperationEnabled	1.3.6.1.4.1.89.59.9.1	INTEGER	read-write	Indicates whether Policy is currently enabled.
T/F rlPolicyGlobalDefaultForwarding	1.3.6.1.4.1.89.59.9.2	TruthValue	read-write	Indicates whether or not the unmach traffic is forwarded or blocked.
INT rlPolicyGlobalAdminTrapfrequency	1.3.6.1.4.1.89.59.9.3	INTEGER	read-write	define the the min number of seconds between successive traps. 0 means no traps will be sent, uints in Sec
INT rlPolicyGlobalOperTrapElapsedTime	1.3.6.1.4.1.89.59.9.4	INTEGER	read-only	show the time out elaps from the last trap sent uints in Sec.
RLP rlPolicyGlobalQoSMode	1.3.6.1.4.1.89.59.9.5	RlPolicyQosMode	read-write	V750 DEPRECATED - replaced with rlPolicyGlobalQosMode field in rlPolicyQosModeGlobalCfg table. user can set the system to operate either in the Basic mode or in the Advanced mode
RLP rlPolicyGlobalTrustMode	1.3.6.1.4.1.89.59.9.6	RlPolicyTrustTypes	read-write	V750 DEPRECATED - replaced with rlPolicyGlobalTrustMode field in rlPolicyQosModeGlobalCfg table. Global Trust state. the value refered to Basic mode and specify the trust mode the device is support. all phisical ports are trusted
INT rlPolicyGlobalDeviceQosOperationTypes	1.3.6.1.4.1.89.59.9.7	INTEGER	read-only	Indicates if the system support basic or advanced mode or Both basic and Advanced
T/F rlPolicyGlobalDscpMutationSupported	1.3.6.1.4.1.89.59.9.8	TruthValue	read-only	mutation over the ingress packet dscp field supported for the device.
T/F rlPolicyGlobalClassifyIpPrecedenceSupported	1.3.6.1.4.1.89.59.9.9	TruthValue	read-only	Indicates if the system support classification according ip precedence most significant 3 bits in the TOS byte
INT rlPolicyGlobalDeviceShapingTypeSupported	1.3.6.1.4.1.89.59.9.10	INTEGER	read-only	Indicates the shaper shaper type supported for the device
T/F rlPolicyGlobalDscpRemarkingSupported	1.3.6.1.4.1.89.59.9.11	TruthValue	read-only	Indicates if dscp remarking supported for the device
INT rlPolicyGlobalqueueSchedulerPerDeviceOrPort	1.3.6.1.4.1.89.59.9.12	INTEGER	read-only	indicates if the system support scheduling configuration per port or per device. device (1 ) or port (2)
rlPolicyMapping	1.3.6.1.4.1.89.59.10
rlPolicyDscpServiceClassTable	1.3.6.1.4.1.89.59.10.1		not-accessible	This table specifies The DSCP to ServiceClass map table
rlPolicyDscpServiceClassEntry	1.3.6.1.4.1.89.59.10.1.1		not-accessible	Each entry in this table describes The ServiceClass assigned to a Dscp value. The index is DSCP represent by rlPolicyDscpIndex
INT rlPolicyDscpIndex	1.3.6.1.4.1.89.59.10.1.1.1	INTEGER	read-only	DSCP value.
INT rlPolicyServiceClassValue	1.3.6.1.4.1.89.59.10.1.1.2	INTEGER	read-write	ServiceClass value.
ROW rlPolicyDscpServiceClassStatus	1.3.6.1.4.1.89.59.10.1.1.3	RowStatus	read-write	The status of a table entry. It is used to delete/Add an entry from this table.
rlPolicyTcpUdpPortServiceClassTable	1.3.6.1.4.1.89.59.10.2		not-accessible	This table specifies TCP/UDP Port to ServiceClass map table
rlPolicyTcpUdpPortServiceClassEntry	1.3.6.1.4.1.89.59.10.2.1		not-accessible	Each entry in this table describes The ServiceClass Value. The index is TCP/UDP port represent by rlPolicyTcpUdpPort
L4P rlPolicyProtocolType	1.3.6.1.4.1.89.59.10.2.1.1	L4ProtType	read-only	TCP/UDP port type.
INT rlPolicyTcpUdpPort	1.3.6.1.4.1.89.59.10.2.1.2	INTEGER	read-only	TCP/UDP port number.
INT rlPolicyMappedServiceClass	1.3.6.1.4.1.89.59.10.2.1.3	INTEGER	read-write	ServiceClass value.
ROW rlPolicyTcpUdpPortServiceClassStatus	1.3.6.1.4.1.89.59.10.2.1.4	RowStatus	read-write	The status of a table entry. It is used to delete/Add an entry from this table.
rlPolicyDscpRemarkTable	1.3.6.1.4.1.89.59.10.3		not-accessible	This table specifies The DSCP Remark table
rlPolicyDscpRemarkEntry	1.3.6.1.4.1.89.59.10.3.1		not-accessible	Each entry in this table describes the new DSCP for the packet. The index is Old DSCP represent by rlPolicyOldDscp
INT rlPolicyRmOldDscp	1.3.6.1.4.1.89.59.10.3.1.1	INTEGER	read-only	Old DSCP.
INT rlPolicyRmNewDscp	1.3.6.1.4.1.89.59.10.3.1.2	INTEGER	read-write	New DSCP for the violation action.
ROW rlPolicyDscpRemarkStatus	1.3.6.1.4.1.89.59.10.3.1.3	RowStatus	read-write	The status of a table entry. It is used to delete/Add an entry from this table.
INT rlPolicyRmNewExceedDscp	1.3.6.1.4.1.89.59.10.3.1.4	INTEGER	read-write	New DSCP for the exceed action.
rlPolicyDscpMutationTable	1.3.6.1.4.1.89.59.10.4		not-accessible	This table specifies The DSCP Mutation table
rlPolicyDscpMutationEntry	1.3.6.1.4.1.89.59.10.4.1		not-accessible	Each entry in this table describes the new DSCP for the packet. The index is Old DSCP represent by rlPolicyOldDscp
INT rlPolicyOldDscp	1.3.6.1.4.1.89.59.10.4.1.1	INTEGER	read-only	Old DSCP.
INT rlPolicyNewDscp	1.3.6.1.4.1.89.59.10.4.1.2	INTEGER	read-write	New DSCP.
ROW rlPolicyDscpMutationStatus	1.3.6.1.4.1.89.59.10.4.1.3	RowStatus	read-write	The status of a table entry. It is used to delete/Add an entry from this table.
rlPolicyTrustModeTable	1.3.6.1.4.1.89.59.10.5		not-accessible	This table specifies the port state for the trusted basic mode
rlPolicyTrustModeEntry	1.3.6.1.4.1.89.59.10.5.1		not-accessible	describes the ports status that belongs to the global trusted state
INT rlPolicyTrustModePortNumber	1.3.6.1.4.1.89.59.10.5.1.1	INTEGER	read-only	phisical port number .
INT rlPolicyTrustModePortState	1.3.6.1.4.1.89.59.10.5.1.2	INTEGER	read-write	the port state for the trusted mode. the port can be enabled or disabled for the basic trust mode
rlPolicyDscpVptTable	1.3.6.1.4.1.89.59.10.6		not-accessible	This table specifies The DSCP to VPT map table
rlPolicyDscpVptEntry	1.3.6.1.4.1.89.59.10.6.1		not-accessible	Each entry in this table describes The VPT assigned to a Dscp value. The index is DSCP represent by rlPolicyDscpValue.
INT rlPolicyDscpValue	1.3.6.1.4.1.89.59.10.6.1.1	INTEGER	read-only	DSCP value.
INT rlPolicyVptValue	1.3.6.1.4.1.89.59.10.6.1.2	INTEGER	read-write	VPT value.
ROW rlPolicyDscpVptStatus	1.3.6.1.4.1.89.59.10.6.1.3	RowStatus	read-write	The status of a table entry. It is used to delete/Add an entry from this table.
rlPolicyDscpToDpTable	1.3.6.1.4.1.89.59.10.7		not-accessible	This table specifies The DSCP To Dp table
rlPolicyDscpToDpEntry	1.3.6.1.4.1.89.59.10.7.1		not-accessible	Each entry in this table describes the new DP for the packet. The index is DSCP represent by rlPolicyDscp
INT rlPolicyDscp	1.3.6.1.4.1.89.59.10.7.1.1	INTEGER	read-only	Packet DSCP.
INT rlPolicyDp	1.3.6.1.4.1.89.59.10.7.1.2	INTEGER	read-write	New DP.
ROW rlPolicyDscpToDpStatus	1.3.6.1.4.1.89.59.10.7.1.3	RowStatus	read-write	The status of a table entry. It is used to delete/Add an entry from this table.
rlPolicyDefaultForwardingTable	1.3.6.1.4.1.89.59.11		not-accessible	This table specifies The default forwarding values : permit or deny for list of specific ports , vlans
rlPolicyDefaultForwardingEntry	1.3.6.1.4.1.89.59.11.1		not-accessible	Since the table is search to find match according to first match Entries with specific protocol should be set before entries for entire layer.
INT rlPolicyDefaultForwardingIndex	1.3.6.1.4.1.89.59.11.1.1	INTEGER	read-only	Default Forwarding Index.
POR rlPolicyDefaultForwardingPortList	1.3.6.1.4.1.89.59.11.1.2	PortList	read-write	Default Forwarding Port List.
VLA rlPolicyDefaultForwardingVlanId1To1024	1.3.6.1.4.1.89.59.11.1.3	VlanList1	read-write	Default Forwarding VlanId List 1.
VLA rlPolicyDefaultForwardingVlanId1025To2048	1.3.6.1.4.1.89.59.11.1.4	VlanList2	read-write	Default Forwarding VlanId List 2.
VLA rlPolicyDefaultForwardingVlanId2049To3072	1.3.6.1.4.1.89.59.11.1.5	VlanList3	read-write	Default Forwarding VlanId List 3.
VLA rlPolicyDefaultForwardingVlanId3073To4096	1.3.6.1.4.1.89.59.11.1.6	VlanList4	read-write	Default Forwarding VlanId List 4.
INT rlPolicyDefaultForwardingLayer	1.3.6.1.4.1.89.59.11.1.7	INTEGER	read-write	Default Forwarding Action specify layer l2 l3 l3-ipv6
INT rlPolicyDefaultForwardingAction	1.3.6.1.4.1.89.59.11.1.8	INTEGER	read-write	Default Forwarding Action specify permit or deny
ROW rlPolicyDefaultForwardingStatus	1.3.6.1.4.1.89.59.11.1.9	RowStatus	read-write	The status of a table entry. It is used to delete/Add an entry from this table.
INT rlPolicyDefaultForwardingProtocol	1.3.6.1.4.1.89.59.11.1.10	INTEGER	read-write	The protocol type to be applied with the default action.
rlPolicyStatistics	1.3.6.1.4.1.89.59.12
rlPolicyPortPolicyStatisticsTable	1.3.6.1.4.1.89.59.12.1		not-accessible	This table specifies statistics counter for policies with specific actions
rlPolicyPortPolicyStatisticsEntry	1.3.6.1.4.1.89.59.12.1.1		not-accessible	Each entry in this table describes counter per port. The index is port represent by rlIfIndex. In each entry represents counter, it's type , it's size and whether it's enabled.
INT rlPolicyPortPolicyStatisticsIfIndex	1.3.6.1.4.1.89.59.12.1.1.1	INTEGER	read-write	Interface index.
STA rlPolicyPortPolicyStatisticsCntrType	1.3.6.1.4.1.89.59.12.1.1.2	StatisticsCntrType	read-only	Counter type.
STA rlPolicyPolicyStatisticsCntrSize	1.3.6.1.4.1.89.59.12.1.1.3	StatisticsCntrNumOfBitsType	read-only	Counter size in bits.
T/F rlPolicyPolicyStatisticsEnableCounting	1.3.6.1.4.1.89.59.12.1.1.4	TruthValue	read-write	Indication whether the counter is enabled.
C64 rlPolicyPolicyStatisticsCounterValue	1.3.6.1.4.1.89.59.12.1.1.5	Counter64	read-only	Counter value.
rlPolicyOutQueueStatisticsTable	1.3.6.1.4.1.89.59.12.2		not-accessible	Each entry in this table describes counter per any permutation of Port/VLAN/Queue/Drop Precedence . Each of the above can a group off 'All'. The index is port represent by rlPolicyOutQueueStatisticsCountrID. In each entry there are fields representing whether the counter is enabled and counters value.
rlPolicyOutQueueStatisticsEntry	1.3.6.1.4.1.89.59.12.2.1		not-accessible	Each entry includes port, vlan, queue, drop precedence and counter value.
INT rlPolicyOutQueueStatisticsCountrID	1.3.6.1.4.1.89.59.12.2.1.1	INTEGER	read-only	Counter id, the key of the table.
POR rlPolicyOutQueueStatisticsIfIndexList	1.3.6.1.4.1.89.59.12.2.1.2	PortList	read-write	Port for which the flow is counted.
T/F rlPolicyOutQueueStatisticsPortAll	1.3.6.1.4.1.89.59.12.2.1.3	TruthValue	read-write	Indication for whether the port is configured as range of all the ports
INT rlPolicyOutQueueStatisticsVlan	1.3.6.1.4.1.89.59.12.2.1.4	INTEGER	read-write	VLAN for which the flow is counted.
T/F rlPolicyOutQueueStatisticsVlanAll	1.3.6.1.4.1.89.59.12.2.1.5	TruthValue	read-write	Indication for whether the Vlan is configured as range of all the Vlans
INT rlPolicyOutQueueStatisticsQueue	1.3.6.1.4.1.89.59.12.2.1.6	INTEGER	read-write	Queue for which the flow is counted.
T/F rlPolicyOutQueueStatisticsQueueAll	1.3.6.1.4.1.89.59.12.2.1.7	TruthValue	read-write	Indication for whether the Queue is configured as range of all the Queues
STA rlPolicyOutQueueStatisticsDP	1.3.6.1.4.1.89.59.12.2.1.8	StatisticsDPType	read-write	Drop Precedence for which the flow is counted.
T/F rlPolicyOutQueueStatisticsDPAll	1.3.6.1.4.1.89.59.12.2.1.9	TruthValue	read-write	Indication for whether the DP is configured as range of all the DPs
C64 rlPolicyOutQueueStatisticsCounterTailDropValue	1.3.6.1.4.1.89.59.12.2.1.10	Counter64	read-only	The counter for tail dropped value.
C64 rlPolicyOutQueueStatisticsCounterAllValue	1.3.6.1.4.1.89.59.12.2.1.11	Counter64	read-only	The counter for all traffic value.
STA rlPolicyOutQueueStatisticsCntrNumOfBits	1.3.6.1.4.1.89.59.12.2.1.12	StatisticsCntrNumOfBitsType	read-only	Counter size in bits for the counter.
ROW rlPolicyOutQueueStatisticsStatus	1.3.6.1.4.1.89.59.12.2.1.13	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table.
rlPolicyGlobalStatisticsCntrsTable	1.3.6.1.4.1.89.59.12.3		not-accessible	This table specifies statistics global counters for specific rules for all ports that they are connected to
rlPolicyGlobalStatisticsCntrsEntry	1.3.6.1.4.1.89.59.12.3.1		not-accessible	Each entry represents global counter.
STA rlPolicyGlobalStatisticsCntrsType	1.3.6.1.4.1.89.59.12.3.1.1	StatisticsCntrType	read-only	Counter type.
STA rlPolicyGlobalStatisticsCntrsNumOfBits	1.3.6.1.4.1.89.59.12.3.1.2	StatisticsCntrNumOfBitsType	read-only	Counter size in bits.
C64 rlPolicyGlobalStatisticsCntrsCounterValue	1.3.6.1.4.1.89.59.12.3.1.3	Counter64	read-only	Counter value.
ROW rlPolicyGlobalStatisticsStatus	1.3.6.1.4.1.89.59.12.3.1.4	RowStatus	read-write	The status of a table entry. It is used to delete an entry from this table.
INT rlPolicyClearCounters	1.3.6.1.4.1.89.59.12.4	INTEGER	read-write	This scalar indicates to clear all the counters.
rlPolicyClassifierUtilization	1.3.6.1.4.1.89.59.13
rlPolicyClassifierUtilizationTable	1.3.6.1.4.1.89.59.13.1		not-accessible	A table containing Classifier utilization information. Each row represents objects for a particular Unit present in this system.
rlPolicyClassifierUtilizationEntry	1.3.6.1.4.1.89.59.13.1.1		not-accessible	A Single entry containing Classifier utilization information.
U32 rlPolicyClassifierUtilizationUnitId	1.3.6.1.4.1.89.59.13.1.1.1	Unsigned32	not-accessible	The Unit ID of this Classifier. must be unique per entry. This is an index into the table.
U32 rlPolicyClassifierUtilizationPercent	1.3.6.1.4.1.89.59.13.1.1.2	Unsigned32	read-only	The classifier utilization percentage.
U32 rlPolicyClassifierUtilizationRulesNumber	1.3.6.1.4.1.89.59.13.1.1.3	Unsigned32	read-only	The classifier utilization number of used rules, in short rules resolution.
U32 rlPolicyIsTCAvailable	1.3.6.1.4.1.89.59.14	Unsigned32	read-only	This scalar indicates the number of currently reserved amount of traffic conditioners.
INT rlPolicyCPUSafeGuardEnable	1.3.6.1.4.1.89.59.15	INTEGER	read-write	This scalar enables/disables CPU Safeguard.
rlPolicyQosModeGlobalCfgTable	1.3.6.1.4.1.89.59.16		not-accessible	This table responsible to set the global qos mode configuration: qos mode, qos trust mode, and if port are trusted by default in qos advanced mode.
rlPolicyQosModeGlobalCfgEntry	1.3.6.1.4.1.89.59.16.1		not-accessible	This table responsible to set the global qos mode configuration: qos mode, qos trust mode, and if port are trusted by default in qos advanced mode. Current implemnetaion assumes only one entry exist.
INT rlPolicyGlobalIndex	1.3.6.1.4.1.89.59.16.1.1	INTEGER	not-accessible	Entry index - currenly only one entry can exist, indexes hard coded with value '1'.
RLP rlPolicyBasicGlobalTrustMode	1.3.6.1.4.1.89.59.16.1.3	RlPolicyTrustTypes	read-write	This field replaces deprecated scalar rlPolicyCliBasicModeCfg. Defines the global qos trust operation mode when qos mode is basic.
RLP rlPolicyAdvcGlobalTrustMode	1.3.6.1.4.1.89.59.16.1.4	RlPolicyTrustTypes	read-write	This field replaces deprecated scalar rlPolicyCliBasicModeCfg. Defines the global qos trust operation mode when qos mode is advanced.
T/F rlPolicyPortTrustAdvancedMode	1.3.6.1.4.1.89.59.16.1.5	TruthValue	read-write	This field specified whether ports are set to trused or not-trusted by default when switching to qos advanced mode.
T/F rlPolicyDscpMutationEnable	1.3.6.1.4.1.89.59.16.1.6	TruthValue	read-write	This field indicates if dscp to dscp mutation mode is enable. It can be set to true in the following terms: 1.rlQosGlobalTrustMode is in {dscp, vpt-dscp} ( rlQosGlobalQoSMode must be basic or advanced) 2.if rlQosGlobalQoSMode is advanced then rlQoSPortTrustAdvancedMode must be set to true.
ROW rlPolicyModeGlobalCfgStatus	1.3.6.1.4.1.89.59.16.1.7	RowStatus	read-write	This status of entry action. In current implementation only one entry exist, therefor only status = active is acceptable.

RFC description

Manages quality-of-service policies including traffic classification, ACLs, and rate limiting on network switches.

Start monitoring OEM switch built on RADLAN switching software/silicon platform (policy-based QoS classification) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RADLAN-POLICY-MIB