All MIBs › PSA-LinBcm5700Trap-MIB
Category: Server Hardware Monitoring
Description: Provides NEC ESMPRO ServerAgents trap notifications for Broadcom BCM5700/5703 Gigabit Ethernet NIC driver events on Linux.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is PSA-LinBcm5700Trap-MIB?
PSA-LinBcm5700Trap-MIB is a vendor MIB used by NEC ESMPRO ServerAgents (Linux) to relay trap notifications originating from the Broadcom BCM5700/5703-series Gigabit Ethernet NIC driver, effectively surfacing NIC/hardware-driver events into an SNMP management console. It exposes trap payload objects describing the affected server partition, event severity level and identifier, plus hardware identity fields for the physical unit (model number, serial number, stepping, part number). Its core purpose is hardware status/fault monitoring of the network interface card: it reports driver-detected NIC problems (e.g., link/hardware faults captured via trapEventLevel and trapEventId) tied to a specific physical adapter identified by trapSerialNo, trapModelNo, and trapStepping, letting an administrator correlate a hardware alert to the exact NIC unit. It depends on the NEC ESMPRO ServerAgent trap-forwarding framework rather than any IETF NIC MIB standard. It is deployed on Linux servers running NEC ESMPRO ServerAgents with Broadcom BCM5700/5703 Gigabit Ethernet adapters, typically in NEC Express5800-series server environments, where PSA-LinBcm5700Trap-MIB SNMP monitoring flags NIC-level hardware faults as they occur.
IPNetwork Monitor allows you to monitor SNMP objects defined in PSA-LinBcm5700Trap-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Fujitsu PRIMEQUEST server partition, Linux, Broadcom BCM5700/5703 Gigabit Ethernet NIC (driver fault traps)
Monitoring Examples
When a BCM5700/5703 NIC driver detects a fault, a trap is generated carrying trapEventLevel and trapEventId to indicate severity/type, trapPartitionName/trapPartitionId to identify the affected server partition, and trapUnitName plus trapModelNo/trapSerialNo/trapStepping/trapPartNo to pin down the exact physical NIC hardware involved. An admin correlating trapSuspect with the reported trapEventLevel would determine whether the event points to a hardware defect requiring adapter replacement versus a transient driver-level condition.
What Can Be Monitored
- NIC event severity level
- NIC event identifier
- affected server partition
- NIC hardware model/serial/stepping identity
- suspect hardware flag
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| TimeTicks | |
| enterprises | |
| mgmt |
From RFC1213-MIB
| DisplayString | |
| mib-2 |
OIDs
RFC description
Fujitsu PRIMEQUEST Linux Broadcom 5700 network adapter trap MIB for device event notifications.
Start monitoring Fujitsu PRIMEQUEST server partition, Linux, Broadcom BCM5700/5703 Gigabit Ethernet NIC (driver fault traps) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.