POLYCOM-VIDEO-MIB

All MIBs › POLYCOM-VIDEO-MIB

Category: Video Conferencing

Description: Provides comprehensive video conferencing management for Polycom endpoints, covering call quality, codec selection, and network performance.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is POLYCOM-VIDEO-MIB?

POLYCOM-VIDEO-MIB is a vendor-specific MIB from Polycom (now part of HP/Poly) for managing video conferencing endpoints such as room and desktop systems. It belongs to the unified-communications/video-conferencing management category, covering call setup configuration alongside operational data on codec selection and network/call quality. Its monitoring value centers on software/service status — call state, active codec, and network performance metrics that indicate whether a video call is healthy — functioning as a health dashboard for the conferencing application layer rather than raw hardware sensors like temperature or fan speed. No module description was available to confirm an explicit dependency, but MIBs of this class typically parallel or layer on standard RTP/video-conferencing management conventions. It is deployed on Polycom video conferencing endpoints and infrastructure within enterprise unified-communications environments, monitored by UC management platforms tracking call quality and device health across an organization's conferencing estate. Engineers can download the POLYCOM-VIDEO-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in POLYCOM-VIDEO-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Polycom video conferencing endpoints (room and desktop systems)

Monitoring Examples

No module description or sample object list is available for this entry, so specific table/object names cannot be confirmed. Based on its stated purpose, a monitoring scenario would typically involve polling call-quality metrics (packet loss, jitter, bitrate) and codec-selection status for active video calls to detect degraded call quality, but no concrete object names can be responsibly cited without inventing them.

What Can Be Monitored

call quality metrics
active codec in use
network performance during calls
call/session state

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
polycom	1.3.6.1.4.1.2684
polycomVideo	1.3.6.1.4.1.2684.1
polycomViewStation	1.3.6.1.4.1.2684.1.1
NTF loginOK	1.3.6.1.4.1.2684.1.1.0.1			Sent when an administrator logs in via embedded UI, ftp, telnet or web.
NTF loginFail	1.3.6.1.4.1.2684.1.1.0.2			Sent when an attempt to log in as an administrator fails via embedded UI, ftp, telnet or web.
NTF lowBattery	1.3.6.1.4.1.2684.1.1.0.3			Sent when the remote has a low battery.
NTF callUp	1.3.6.1.4.1.2684.1.1.0.4			When a call is successfully connected, this notifies the SNMP manager of the far site number.
NTF callDown	1.3.6.1.4.1.2684.1.1.0.5			When a call is disconnected with normal call clearing, this notifies the SNMP manager of the far site number.
NTF callFail	1.3.6.1.4.1.2684.1.1.0.6			When a call is disconnected with a cause code other than normal, this notifies the SNMP manager of the reason.
NTF userAssist	1.3.6.1.4.1.2684.1.1.0.7			Sent when a user sends a help request to GMS.
NTF visualConcertUp	1.3.6.1.4.1.2684.1.1.0.8			Sent when a visual concert pod is connected.
NTF visualConcertOff	1.3.6.1.4.1.2684.1.1.0.9			Sent when a visual concert pod is disconnected.
NTF micChange	1.3.6.1.4.1.2684.1.1.0.10			Sent when a mic pod or VTX is connected or disconnected and includes the total mic count.
NTF autoAnswerChange	1.3.6.1.4.1.2684.1.1.0.11			Sent when the auto answer setting is changed.
NTF timeServerUp	1.3.6.1.4.1.2684.1.1.0.12			Sent when the time server successfully connects.
NTF timeServerDown	1.3.6.1.4.1.2684.1.1.0.13			Sent when the time server is enabled but does not connect correctly.
NTF timeServerOn	1.3.6.1.4.1.2684.1.1.0.14			Sent when the time server is enabled.
NTF timeServerOff	1.3.6.1.4.1.2684.1.1.0.15			Sent when the time server is disabled.
NTF gdsUp	1.3.6.1.4.1.2684.1.1.0.16			Sent when a global directory server successfully connects.
NTF gdsDown	1.3.6.1.4.1.2684.1.1.0.17			Sent when a global directory server is enabled, but not connected correctly.
NTF gdsOff	1.3.6.1.4.1.2684.1.1.0.18			Sent when a global directory server is disabled.
NTF gatekeeperReg	1.3.6.1.4.1.2684.1.1.0.19			Sent when a gatekeeper is registered successfully.
NTF gatekeeperDown	1.3.6.1.4.1.2684.1.1.0.20			Sent when a gatekeeper is specified, but not registered successfully.
NTF gatekeeperOff	1.3.6.1.4.1.2684.1.1.0.21			Sent when a gatekeeper is disabled.
NTF ipAddressChange	1.3.6.1.4.1.2684.1.1.0.22			Sent when the system IP address has changed.
NTF interfaceTypeChange	1.3.6.1.4.1.2684.1.1.0.23			Sent when the system network interface card type has changed.
NTF lineEnabled	1.3.6.1.4.1.2684.1.1.0.24			Sent when a V.35 or ISDN line has been enabled.
NTF lineDisabled	1.3.6.1.4.1.2684.1.1.0.25			Sent when a V.35 or ISDN line has been disabled.
NTF lineUp	1.3.6.1.4.1.2684.1.1.0.26			Sent when a V.35 or ISDN line has been enabled and becomes available for placing a call.
NTF lineDown	1.3.6.1.4.1.2684.1.1.0.27			Sent when a V.35 or ISDN line has been enabled, but is not working correctly.
NTF v35PortsEnabled	1.3.6.1.4.1.2684.1.1.0.28			Sent when the V.35 enabled ports setting has changed.
NTF lineCountChange	1.3.6.1.4.1.2684.1.1.0.29			Sent when the total of available V.35 or ISDN lines has changed.
NTF mainCameraUp	1.3.6.1.4.1.2684.1.1.0.30			Sent when the main camera is working correctly.
NTF mainCameraDown	1.3.6.1.4.1.2684.1.1.0.31			Sent when the main camera is not working correctly.
NTF upnpChange	1.3.6.1.4.1.2684.1.1.0.32			Sent when the state of the UPnP device changes.
NTF percentPacketLossExcessive	1.3.6.1.4.1.2684.1.1.0.33			Sent when the combined tx/rx percentage of packet loss exceeds 1 percent based on 1 minute samples.
NTF jitterExcessive	1.3.6.1.4.1.2684.1.1.0.34			Sent when the combined tx/rx average jitter exceeds 35 ms based on 1 minute samples.
NTF latencyExcessive	1.3.6.1.4.1.2684.1.1.0.35			Sent when the combined tx/rx average latency exceeds 150 ms based on 1 minute samples.
INT polycomVSAuthLocation	1.3.6.1.4.1.2684.1.1.1	INTEGER	read-only	The origin of the last attempted admin login. Valid values are 0(local), 1(ftp), 2(telnet) or 3(web).
STR polycomVSPhoneNumber	1.3.6.1.4.1.2684.1.1.2	DisplayString	read-only	The far site number.
STR polycomVSReason	1.3.6.1.4.1.2684.1.1.3	DisplayString	read-only	The cause code associated with a call disconnecting.
STR polycomVSPlead	1.3.6.1.4.1.2684.1.1.4	DisplayString	read-only	The contact phone number for the user who sent the help request to GMS.
STR polycomVSMicData	1.3.6.1.4.1.2684.1.1.5	DisplayString	read-only	The current total connected mic count or VTX status.
STR polycomVSAutoAnswerSetting	1.3.6.1.4.1.2684.1.1.6	DisplayString	read-only	The current user-specified auto answer setting (i.e. Yes, No, Do_Not_Disturb).
STR polycomVSTimeServerAddress	1.3.6.1.4.1.2684.1.1.7	DisplayString	read-only	The current time server address.
STR polycomVSTimeServerSetting	1.3.6.1.4.1.2684.1.1.8	DisplayString	read-only	The current time server setting.
STR polycomVSGDSAddress	1.3.6.1.4.1.2684.1.1.9	DisplayString	read-only	The current global directory server address related to a certain GDS event.
STR polycomVSGatekeeperAddress	1.3.6.1.4.1.2684.1.1.10	DisplayString	read-only	The current gatekeeper address related to a certain gatekeeper event.
STR polycomVSPreviousIPAddress	1.3.6.1.4.1.2684.1.1.11	DisplayString	read-only	The previous IP address.
STR polycomVSCurrentIPAddress	1.3.6.1.4.1.2684.1.1.12	DisplayString	read-only	The current IP address.
STR polycomVSPreviousNicType	1.3.6.1.4.1.2684.1.1.13	DisplayString	read-only	The previous network interface card type.
STR polycomVSCurrentNicType	1.3.6.1.4.1.2684.1.1.14	DisplayString	read-only	The current network interface card type.
STR polycomVSNicLineNumber	1.3.6.1.4.1.2684.1.1.15	DisplayString	read-only	The V.35 or ISDN line number related to a certain line event.
STR polycomVSPreviousNicLineCount	1.3.6.1.4.1.2684.1.1.16	DisplayString	read-only	The total nic line count (i.e. ISDN Quad BRI = 4 lines).
STR polycomVSCurrentNicLineCount	1.3.6.1.4.1.2684.1.1.17	DisplayString	read-only	The current nic line count (i.e. ISDN Quad BRI = 4 lines).
STR polycomVSV35PortsEnabled	1.3.6.1.4.1.2684.1.1.18	DisplayString	read-only	The current user specified V.35 ports enabled setting (i.e. 1, 1+2, none).
STR polycomVSAuthClientAddress	1.3.6.1.4.1.2684.1.1.19	DisplayString	read-only	The address of the login client.
STR polycomVSUPnPStatus	1.3.6.1.4.1.2684.1.1.20	DisplayString	read-only	The current status of the UPnP device.
STR polycomVSPercentPacketLoss	1.3.6.1.4.1.2684.1.1.21	DisplayString	read-only	The current combined (audio/video) average percentage packet loss when in an H.323 call.
STR polycomVSJitter	1.3.6.1.4.1.2684.1.1.22	DisplayString	read-only	The current combined (audio/video) cumulative average jitter (in ms) when in an H.323 call.
STR polycomVSLatency	1.3.6.1.4.1.2684.1.1.23	DisplayString	read-only	The current average latency based on round trip delay when in an H.323 call.
polycomAudio	1.3.6.1.4.1.2684.2
polycomData	1.3.6.1.4.1.2684.3

RFC description

Monitors Polycom video conferencing devices including call status, authentication, and device settings.

Start monitoring Polycom video conferencing endpoints, room and desktop systems with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download POLYCOM-VIDEO-MIB

What Is POLYCOM-VIDEO-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description