PDN-HDSL2-SHDSL-LINE-MIB

All MIBs › PDN-HDSL2-SHDSL-LINE-MIB

Organization: Paradyne Networks MIB Working Group Other information about group editing the MIB

Last Updated: 2005-01-28

Category: DSL and Broadband

Description: Manages HDSL2 and SHDSL line configuration, attainable rates, loop attenuation, and error counts on Paradyne DSL gear.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PDN-HDSL2-SHDSL-LINE-MIB?

PDN-HDSL2-SHDSL-LINE-MIB is a Paradyne (later part of Zhone/DZS) enterprise MIB for managing HDSL2 and G.shdsl.bis DSL lines, created as an interim vendor extension to support G.shdsl.bis ahead of updates to the IETF standard HDSL2-SHDSL-LINE-MIB (RFC 3276). It exposes extended span status, endpoint configuration (including wire pair and alarm-configuration profile), and current endpoint performance objects such as attainable and actual line rate, attenuation, and SNR margin. This is a hardware/line-health monitoring MIB used to assess the physical quality of copper DSL loops — degrading attenuation or SNR margin readings, or an actual line rate falling below the attainable rate, indicate a failing or noisy line before it drops entirely. It explicitly depends on and extends the IETF standard HDSL2-SHDSL-LINE-MIB (RFC 3276) and the related G.shdsl.bis ITU specification, reusing that standard's endpoint indexing model while adding vendor-specific fields. It is deployed on Paradyne DSL access/transport equipment in carrier or enterprise access networks delivering symmetric high-speed DSL service over copper, with the PDN-HDSL2-SHDSL-LINE-MIB MIB serving as the vendor's interim extension of the IETF standard.

IPNetwork Monitor allows you to monitor SNMP objects defined in PDN-HDSL2-SHDSL-LINE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Paradyne DSL access/transport equipment

Monitoring Examples

An operator would poll pdnHdsl2ShdslEndpointCurrTable/pdnHdsl2ShdslEndpointCurrEntry for pdnHdsl2ShdslEndpointCurrAtn (attenuation) and pdnHdsl2ShdslEndpointCurrSnrMgn (SNR margin) per pdnHdsl2ShdslEndpointWirePair, and a rising attenuation or falling SNR margin signals a deteriorating copper pair. Comparing pdnHdsl2ShdslStatusActualLineRate against pdnHdsl2ShdslStatusMaxAttainableLineRate in pdnHdsl2ShdslSpanStatusExtTable reveals whether the line is running below its potential capacity, and pdnHdsl2ShdslLineNotifications would alert when an alarm profile configured via pdnHdsl2ShdslEndpointAlarmConfProfile is triggered.

What Can Be Monitored

line attenuation
SNR margin
actual vs. maximum attainable line rate
endpoint alarm profile status
wire pair configuration

Imported Objects

From HDSL2-SHDSL-LINE-MIB

Hdsl2Shdsl1DayIntervalCount
Hdsl2ShdslPerfCurrDayCount
Hdsl2ShdslPerfTimeElapsed
hdsl2ShdslEndpointSide	OBJECT-TYPE
hdsl2ShdslEndpointThreshCRCanomalies	OBJECT-TYPE
hdsl2ShdslEndpointThreshES	OBJECT-TYPE
hdsl2ShdslEndpointThreshLOSWS	OBJECT-TYPE
hdsl2ShdslEndpointThreshLoopAttenuation	OBJECT-TYPE
hdsl2ShdslEndpointThreshSES	OBJECT-TYPE
hdsl2ShdslEndpointThreshSNRMargin	OBJECT-TYPE
hdsl2ShdslEndpointThreshUAS	OBJECT-TYPE
hdsl2ShdslInvIndex	OBJECT-TYPE
hdsl2ShdslSpanConfProfileName	OBJECT-TYPE

From IF-MIB

ifIndex

OBJECT-TYPE

From PDN-HEADER-MIB

pdn-interfaces

From PerfHist-TC-MIB

PerfCurrentCount
PerfIntervalCount

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using pdnHdsl2ShdslEndpointES OID:

Select a Paradyne DSL access/transport equipment (HDSL2/G.shdsl.bis line quality) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type pdnHdsl2ShdslEndpointES into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the count of Errored Seconds (ES) on this endpoint since the xU was last restarted. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
pdnHdsl2ShdslLineMIB	1.3.6.1.4.1.1795.2.24.2.6.23			The primary purpose of this MIB is to allow support of G.shdsl.bis based on the ITU Temporary Document, DC-R15, April 2003, until such a time as the `standard' MIB, HDSL2-SHDSL-LINE-MIB, RFC 3276, May 2002 is updated to support G.shdsl.bis. In addition to providing support for G.shdsl.bis, this MIB may support SHDSL objects that are unique to the enterprise. Decisions as far as how this MIB is supported with respect to the `standard' MIB will be made in an individual basis by those involved with specific projects; those decisions are not dictated here. The following documents should be referenced with respect to this MIB: [G.991.2] ITU-T G991.2 `Single-pair high-speed digital subscriber line (SHDSL) transceivers,' December 2003. [DC-R15] ITU Study Group 15 Temporary Document `G.shdsl.bis: Draft Text`, April 2003. [RFC 3276] Ray, B., Abbi, R. `HDSL2-SHDSL-LINE-MIB', May 2002. ===================================================================== == == == Copyright (C) 2004 Paradyne Corporation. == == == =====================================================================
pdnHdsl2ShdslLineNotifications	1.3.6.1.4.1.1795.2.24.2.6.23.0
NTF pdnHdsl2ShdslLoopAttenCrossing	1.3.6.1.4.1.1795.2.24.2.6.23.0.1			This notification indicates that the loop attenuation threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation value) has been reached/exceeded for the DSL segment endpoint.
NTF pdnHdsl2ShdslSNRMarginCrossing	1.3.6.1.4.1.1795.2.24.2.6.23.0.2			This notification indicates that the SNR margin threshold (as per the hdsl2ShdslEndpointThreshSNRMargin value) has been reached/exceeded for the DSL segment endpoint.
NTF pdnHdsl2ShdslPerfESThresh	1.3.6.1.4.1.1795.2.24.2.6.23.0.3			This notification indicates that the errored seconds threshold (as per the hdsl2ShdslEndpointThreshES value) has been reached/ exceeded for the DSL segment endpoint.
NTF pdnHdsl2ShdslPerfSESThresh	1.3.6.1.4.1.1795.2.24.2.6.23.0.4			This notification indicates that the severely errored seconds threshold (as per the hdsl2ShdslEndpointThreshSES value) has been reached/exceeded for the DSL Segment Endpoint.
NTF pdnHdsl2ShdslPerfCRCanomaliesThresh	1.3.6.1.4.1.1795.2.24.2.6.23.0.5			This notification indicates that the CRC anomalies threshold (as per the hdsl2ShdslEndpointThreshCRCanomalies value) has been reached/exceeded for the DSL Segment Endpoint.
NTF pdnHdsl2ShdslPerfLOSWSThresh	1.3.6.1.4.1.1795.2.24.2.6.23.0.6			This notification indicates that the LOSW seconds threshold (as per the hdsl2ShdslEndpointThreshLOSWS value) has been reached/exceeded for the DSL segment endpoint.
NTF pdnHdsl2ShdslPerfUASThresh	1.3.6.1.4.1.1795.2.24.2.6.23.0.7			This notification indicates that the unavailable seconds threshold (as per the hdsl2ShdslEndpointThreshUAS value) has been reached/exceeded for the HDSL2/SHDSL segment endpoint.
NTF pdnHdsl2ShdslpowerBackoff	1.3.6.1.4.1.1795.2.24.2.6.23.0.8			This notification indicates that the bit setting for powerBackoff in the pdnHdsl2ShdslEndpointCurrStatus object for this endpoint has changed.
NTF pdnHdsl2ShdsldeviceFault	1.3.6.1.4.1.1795.2.24.2.6.23.0.9			This notification indicates that the bit setting for deviceFault in the pdnHdsl2ShdslEndpointCurrStatus object for this endpoint has changed.
NTF pdnHdsl2ShdsldcContinuityFault	1.3.6.1.4.1.1795.2.24.2.6.23.0.10			This notification indicates that the bit setting for dcContinuityFault in the pdnHdsl2ShdslEndpointCurrStatus object for this endpoint has changed.
NTF pdnHdsl2ShdslconfigInitFailure	1.3.6.1.4.1.1795.2.24.2.6.23.0.11			This notification indicates that the bit setting for configInitFailure in the pdnHdsl2ShdslEndpointCurrStatus object for this endpoint has changed.
NTF pdnHdsl2ShdslprotocolInitFailure	1.3.6.1.4.1.1795.2.24.2.6.23.0.12			This notification indicates that the bit setting for protocolInitFailure in the pdnHdsl2ShdslEndpointCurrStatus object for this endpoint has changed.
NTF pdnHdsl2ShdslnoNeighborPresent	1.3.6.1.4.1.1795.2.24.2.6.23.0.13			This notification indicates that the bit setting for noNeighborPresent in the pdnHdsl2ShdslEndpointCurrStatus object for this endpoint has changed.
pdnHdsl2ShdslLineObjects	1.3.6.1.4.1.1795.2.24.2.6.23.1
pdnHdsl2ShdslSpanStatusExtTable	1.3.6.1.4.1.1795.2.24.2.6.23.1.1		not-accessible	This table extends the hdsl2ShdslSpanStatusTable defined in the HDSL2-SHDSL-LINE-MIB (the `standard' MIB) which provides overall information of DSL spans.
pdnHdsl2ShdslSpanStatusExtEntry	1.3.6.1.4.1.1795.2.24.2.6.23.1.1.1		not-accessible	An entry extends the hdsl2ShdslSpanStatusEntry defined in [RFC 3276]. Each entry corresponds to a DSL line.
U32 pdnHdsl2ShdslStatusMaxAttainableLineRate	1.3.6.1.4.1.1795.2.24.2.6.23.1.1.1.1	Unsigned32	read-only	Contains the maximum attainable line rate, in bps, in this DSL span.
U32 pdnHdsl2ShdslStatusActualLineRate	1.3.6.1.4.1.1795.2.24.2.6.23.1.1.1.2	Unsigned32	read-only	Contains the actual line rate, in bps, in this DSL span. This is based upon measurements made during line probing.
pdnHdsl2ShdslEndpointConfTable	1.3.6.1.4.1.1795.2.24.2.6.23.1.2		not-accessible	This table supports configuration parameters for segment endpoints in a HDSL2/SHDSL line. As this table is indexed by ifIndex, it MUST be maintained in a persistent manner.
pdnHdsl2ShdslEndpointConfEntry	1.3.6.1.4.1.1795.2.24.2.6.23.1.2.1		not-accessible	Each entry represents a single segment endpoint in a HDSL2/SHDSL line. It is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, the side of the unit, and the wire-pair of the associated modem.
PDN pdnHdsl2ShdslEndpointWirePair	1.3.6.1.4.1.1795.2.24.2.6.23.1.2.1.1	PdnHdsl2ShdslWirePair	not-accessible	The wire-pair of the modem associated with this segment endpoint as per the PdnHdsl2ShdslWirePair textual convention.
STR pdnHdsl2ShdslEndpointAlarmConfProfile	1.3.6.1.4.1.1795.2.24.2.6.23.1.2.1.2	SnmpAdminString	read-write	This object configures the alarm threshold values to be used for this segment endpoint. The values are obtained from the alarm configuration profile referenced by this object. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero- length SnmpAdminString). If the value is a zero-length SnmpAdminString, the endpoint uses the default Alarm Configuration Profile for the associated span as per the hdsl2ShdslSpanConfAlarmProfile object in the hdsl2ShdslSpanConfTable. The default value of this object is a zero-length SnmpAdminString. Any attempt to set this object to a value that is not the value of the index for an active entry in the profile table, hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected.
pdnHdsl2ShdslEndpointCurrTable	1.3.6.1.4.1.1795.2.24.2.6.23.1.3		not-accessible	This table contains current status and performance information for segment endpoints in HDSL2/SHDSL Lines. As with other tables in this MIB indexed by ifIndex, entries in this table MUST be maintained in a persistent manner.
pdnHdsl2ShdslEndpointCurrEntry	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1		not-accessible	Each entry contains status and performance information relating to a single segment endpoint. It is indexed by the ifIndex of the HDSL2/SHDSL line, the UnitId of the associated unit, the side of the unit, and the wire-pair of the associated modem.
I32 pdnHdsl2ShdslEndpointCurrAtn	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.1	Integer32	read-only	The current loop attenuation for this endpoint as reported in a Network or Customer Side Performance Status message.
I32 pdnHdsl2ShdslEndpointCurrSnrMgn	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.2	Integer32	read-only	The current SNR margin for this endpoint as reported in a Status Response/SNR message.
BIT pdnHdsl2ShdslEndpointCurrStatus	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.3	Bits	read-only	Contains the current state of the endpoint. This is a bitmap of possible conditions. The various bit positions are: noDefect There no defects on the line. powerBackoff Indicates enhanced Power Backoff. deviceFault Indicates a vendor-dependent diagnostic or self-test fault has been detected. dcContinuityFault Indicates vendor-dependent conditions that interfere with span powering such as short and open circuits. snrMarginAlarm Indicates that the SNR margin has dropped below the alarm threshold. loopAttenuationAlarm Indicates that the loop attenuation exceeds the alarm threshold. loswFailureAlarm Indicates a forward LOSW alarm. configInitFailure Endpoint failure during initialization due to paired endpoint not able to support requested configuration. protocolInitFailure Endpoint failure during initialization due to incompatible protocol used by the paired endpoint. noNeighborPresent Endpoint failure during initialization due to no activation sequence detected from paired endpoint. loopbackActive A loopback is currently active at this Segment Endpoint. This is intended to supplement ifOperStatus. Note that there is a 1-1 relationship between the status bits defined in this object and the notification thresholds defined elsewhere in this MIB.
C32 pdnHdsl2ShdslEndpointESEx	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.4	Counter32	read-only	Count of Errored Seconds (ES) on this endpoint since the xU was last restarted.
C32 pdnHdsl2ShdslEndpointSES	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.5	Counter32	read-only	Count of Severely Errored Seconds (SES) on this endpoint since the xU was last restarted.
C32 pdnHdsl2ShdslEndpointCRCanomalies	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.6	Counter32	read-only	Count of CRC anomalies on this endpoint since the xU was last restarted.
C32 pdnHdsl2ShdslEndpointLOSWS	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.7	Counter32	read-only	Count of Loss of Sync Word (LOSW) Seconds on this endpoint since the xU was last restarted.
C32 pdnHdsl2ShdslEndpointUAS	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.8	Counter32	read-only	Count of Unavailable Seconds (UAS) on this endpoint since the xU was last restarted.
HDS pdnHdsl2ShdslEndpointCurr15MinTimeElapsed	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.9	Hdsl2ShdslPerfTimeElapsed	read-only	Total elapsed seconds in the current 15-minute interval.
PER pdnHdsl2ShdslEndpointCurr15MinES	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.10	PerfCurrentCount	read-only	Count of Errored Seconds (ES) in the current 15-minute interval.
PER pdnHdsl2ShdslEndpointCurr15MinSES	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.11	PerfCurrentCount	read-only	Count of Severely Errored Seconds (SES) in the current 15-minute interval.
PER pdnHdsl2ShdslEndpointCurr15MinCRCanomalies	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.12	PerfCurrentCount	read-only	Count of CRC anomalies in the current 15-minute interval.
PER pdnHdsl2ShdslEndpointCurr15MinLOSWS	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.13	PerfCurrentCount	read-only	Count of Loss of Sync Word (LOSW) Seconds in the current 15-minute interval.
PER pdnHdsl2ShdslEndpointCurr15MinUAS	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.14	PerfCurrentCount	read-only	Count of Unavailable Seconds (UAS) in the current 15-minute interval.
HDS pdnHdsl2ShdslEndpointCurr1DayTimeElapsed	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.15	Hdsl2ShdslPerfTimeElapsed	read-only	Number of seconds that have elapsed since the beginning of the current 1-day interval.
HDS pdnHdsl2ShdslEndpointCurr1DayES	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.16	Hdsl2ShdslPerfCurrDayCount	read-only	Count of Errored Seconds (ES) during the current day as measured by pdnHdsl2ShdslEndpointCurr1DayTimeElapsed.
HDS pdnHdsl2ShdslEndpointCurr1DaySES	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.17	Hdsl2ShdslPerfCurrDayCount	read-only	Count of Severely Errored Seconds (SES) during the current day as measured by pdnHdsl2ShdslEndpointCurr1DayTimeElapsed.
HDS pdnHdsl2ShdslEndpointCurr1DayCRCanomalies	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.18	Hdsl2ShdslPerfCurrDayCount	read-only	Count of CRC anomalies during the current day as measured by pdnHdsl2ShdslEndpointCurr1DayTimeElapsed.
HDS pdnHdsl2ShdslEndpointCurr1DayLOSWS	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.19	Hdsl2ShdslPerfCurrDayCount	read-only	Count of Loss of Sync Word (LOSW) Seconds during the current day as measured by pdnHdsl2ShdslEndpointCurr1DayTimeElapsed.
HDS pdnHdsl2ShdslEndpointCurr1DayUAS	1.3.6.1.4.1.1795.2.24.2.6.23.1.3.1.20	Hdsl2ShdslPerfCurrDayCount	read-only	Count of Unavailable Seconds (UAS) during the current day as measured by pdnHdsl2ShdslEndpointCurr1DayTimeElapsed.
pdnHdsl2Shdsl15MinIntervalTable	1.3.6.1.4.1.1795.2.24.2.6.23.1.4		not-accessible	This table provides one row for each HDSL2/SHDSL endpoint performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
pdnHdsl2Shdsl15MinIntervalEntry	1.3.6.1.4.1.1795.2.24.2.6.23.1.4.1		not-accessible	An entry in the pdnHdsl2Shdsl15MinIntervalTable.
U32 pdnHdsl2Shdsl15MinIntervalNumber	1.3.6.1.4.1.1795.2.24.2.6.23.1.4.1.1	Unsigned32	not-accessible	Performance Data Interval number. 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
NUM pdnHdsl2Shdsl15MinIntervalES	1.3.6.1.4.1.1795.2.24.2.6.23.1.4.1.2	PerfIntervalCount	read-only	Count of Errored Seconds (ES) during the interval.
NUM pdnHdsl2Shdsl15MinIntervalSES	1.3.6.1.4.1.1795.2.24.2.6.23.1.4.1.3	PerfIntervalCount	read-only	Count of Severely Errored Seconds (SES) during the interval.
NUM pdnHdsl2Shdsl15MinIntervalCRCanomalies	1.3.6.1.4.1.1795.2.24.2.6.23.1.4.1.4	PerfIntervalCount	read-only	Count of CRC anomalies during the interval.
NUM pdnHdsl2Shdsl15MinIntervalLOSWS	1.3.6.1.4.1.1795.2.24.2.6.23.1.4.1.5	PerfIntervalCount	read-only	Count of Loss of Sync Word (LOSW) Seconds during the interval.
NUM pdnHdsl2Shdsl15MinIntervalUAS	1.3.6.1.4.1.1795.2.24.2.6.23.1.4.1.6	PerfIntervalCount	read-only	Count of Unavailable Seconds (UAS) during the interval.
pdnHdsl2Shdsl1DayIntervalTable	1.3.6.1.4.1.1795.2.24.2.6.23.1.5		not-accessible	This table provides one row for each HDSL2/SHDSL endpoint performance data collection interval. This table contains live data from equipment. As such, it is NOT persistent.
pdnHdsl2Shdsl1DayIntervalEntry	1.3.6.1.4.1.1795.2.24.2.6.23.1.5.1		not-accessible	An entry in the pdnHdsl2Shdsl1DayIntervalTable.
U32 pdnHdsl2Shdsl1DayIntervalNumber	1.3.6.1.4.1.1795.2.24.2.6.23.1.5.1.1	Unsigned32	not-accessible	History Data Interval number. Interval 1 is the the most recent previous day; interval 30 is 30 days ago. Intervals 2..30 are optional.
HDS pdnHdsl2Shdsl1DayIntervalMoniSecs	1.3.6.1.4.1.1795.2.24.2.6.23.1.5.1.2	Hdsl2ShdslPerfTimeElapsed	read-only	The amount of time in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
NUM pdnHdsl2Shdsl1DayIntervalES	1.3.6.1.4.1.1795.2.24.2.6.23.1.5.1.3	Hdsl2Shdsl1DayIntervalCount	read-only	Count of Errored Seconds (ES) during the 1-day interval as measured by pdnHdsl2Shdsl1DayIntervalMoniSecs.
NUM pdnHdsl2Shdsl1DayIntervalSES	1.3.6.1.4.1.1795.2.24.2.6.23.1.5.1.4	Hdsl2Shdsl1DayIntervalCount	read-only	Count of Severely Errored Seconds (SES) during the 1-day interval as measured by pdnHdsl2Shdsl1DayIntervalMoniSecs.
NUM pdnHdsl2Shdsl1DayIntervalCRCanomalies	1.3.6.1.4.1.1795.2.24.2.6.23.1.5.1.5	Hdsl2Shdsl1DayIntervalCount	read-only	Count of CRC anomalies during the 1-day interval as measured by pdnHdsl2Shdsl1DayIntervalMoniSecs.
NUM pdnHdsl2Shdsl1DayIntervalLOSWS	1.3.6.1.4.1.1795.2.24.2.6.23.1.5.1.6	Hdsl2Shdsl1DayIntervalCount	read-only	Count of Loss of Sync Word (LOSW) Seconds during the 1-day interval as measured by pdnHdsl2Shdsl1DayIntervalMoniSecs.
NUM pdnHdsl2Shdsl1DayIntervalUAS	1.3.6.1.4.1.1795.2.24.2.6.23.1.5.1.7	Hdsl2Shdsl1DayIntervalCount	read-only	Count of Unavailable Seconds (UAS) during the 1-day interval as measured by pdnHdsl2Shdsl1DayIntervalMoniSecs.
pdnHdsl2ShdslSpanConfProfileExtTable	1.3.6.1.4.1.1795.2.24.2.6.23.1.6		not-accessible	This table extends the hdsl2ShdslSpanConfProfileTable defined in the HDSL2-SHDSL-LINE-MIB (the `standard' MIB) which supports definitions of span configuration profiles for DSL lines. IMPORTANT NOTE: This table is a 'pseudo-augments' of the hdsl2ShdslSpanConfProfileTable. Refer to the April 21, 2004 revision description for a discussion on why the table is indexed as opposed to augments. This table shares the same table table index as the hdsl2ShdslSpanConfProfileTable. However, this table does not have a row status object. Therefore, rows are created or deleted in this table by creating or deleting rows in the hdsl2ShdslSpanConfProfileTable.
pdnHdsl2ShdslSpanConfProfileExtEntry	1.3.6.1.4.1.1795.2.24.2.6.23.1.6.1		not-accessible	An entry extends the hdsl2ShdslSpanConfProfileEntry defined in [RFC 3276]. Each entry corresponds to a profile for a span.
INT pdnHdsl2ShdslSpanConfWireInterface	1.3.6.1.4.1.1795.2.24.2.6.23.1.6.1.1	INTEGER	read-create	This object configures number of wires that are operational for this span. The following values are defined for this object: twoWire(1) - 2-wire mode fourWire(2) - 4-wire mode sixWire(3) - 6-wire mode eightWire(4) - 8-wire mode
U32 pdnHdsl2ShdslSpanConfMinLineRate	1.3.6.1.4.1.1795.2.24.2.6.23.1.6.1.2	Unsigned32	read-create	This object configures the minimum transmission rate, in multiples of 64 kbits per second, for the associated DSL Line in bits-per-second (bps). If the minimum line rate equals the maximum line rate (pdnHdsl2ShdslSpanConfMaxLineRate), the line rate is considered `fixed'. If the minimum line rate is less than the maximum line rate, the line is considered `rate-adaptive'.
U32 pdnHdsl2ShdslSpanConfMaxLineRate	1.3.6.1.4.1.1795.2.24.2.6.23.1.6.1.3	Unsigned32	read-create	This object configures the maximum transmission rate, in multiples of 64 kbits per second, for the associated DSL Line in bits-per-second (bps). If the minimum line rate (pdnHdsl2Shdsl- SpanConfMinLineRate) equals the maximum line rate, the line rate is considered `fixed'. if the minimum line rate is less than the maximum line rate, the line rate is considered `rate-adaptive'.
pdnHdsl2ShdslIfTable	1.3.6.1.4.1.1795.2.24.2.6.23.1.7		not-accessible	This table provides objects related to a particular interface and each entry corresponds to an ifIndex.
pdnHdsl2ShdslIfEntry	1.3.6.1.4.1.1795.2.24.2.6.23.1.7.1		not-accessible	An entry in the pdnHdsl2ShdslIfTableTable.
INT pdnHdsl2ShdslIfTableEquipMode	1.3.6.1.4.1.1795.2.24.2.6.23.1.7.1.1	INTEGER	read-write	This object allows the mode of the equipment to be set.
INT pdnHdsl2ShdslExtendedRateMode	1.3.6.1.4.1.1795.2.24.2.6.23.1.8	INTEGER	read-write	This object is used to select a mode of operation that supports extended rates. Some hardware implementations require different configurations base on whether or not higher speed rates are desired. For example, an implementation may require different code be loaded in a digital signal processor or an implementation may dictate that fewer subscriber ports are supported for a higher data rate. The payload5696(2) corresponds to the 5696 kbits per second rate specified in G.991.2, Annex F.
pdnHdsl2ShdslLineAFNs	1.3.6.1.4.1.1795.2.24.2.6.23.2
pdnHdsl2ShdslLineConformance	1.3.6.1.4.1.1795.2.24.2.6.23.3
pdnHdsl2ShdslLineCompliances	1.3.6.1.4.1.1795.2.24.2.6.23.3.1
pdnHdsl2ShdslLineMIBCompliance	1.3.6.1.4.1.1795.2.24.2.6.23.3.1.1			The compliance statement for pdnHdsl2ShdslLineMIB entities which implement the pdnHdsl2ShdslLineMIB.
pdnHdsl2ShdslLineGroups	1.3.6.1.4.1.1795.2.24.2.6.23.3.2
pdnHdsl2ShdslLineObjGroups	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1
pdnHdsl2ShdslSpanShdslStatusGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1.1			This group supports objects for retrieving SHDSL-specific span related status.
pdnHdsl2ShdslEndpointConfGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1.2			This group supports objects for configuring parameters for segment endpoints in SHDSL lines.
pdnHdsl2ShdslEndpointCurrGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1.3			This group supports objects which provide current status and performance measurements relating to segment endpoints in DSL lines.
pdnHdsl2Shdsl15MinIntervalGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1.4			This group supports objects which maintain historic performance measurements relating to segment endpoints in DSL lines.
pdnHdsl2Shdsl1DayIntervalGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1.5			This group supports objects which maintain historic performance measurements relating to segment endpoints in DSL line in 1-day intervals.
pdnHdsl2ShdslSpanConfProfileGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1.6			This group supports objects that constitute configuration profiles for configuring span related parameters in DSL lines.
pdnHdsl2ShdslIfTableGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1.7			This group supports objects on a per-interface basis.
pdnHdsl2ShdslExtendedRateModeGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.1.8			This group supports objects to select the extended base data rate mode.
pdnHdsl2ShdslLineAfnGroups	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.2
pdnHdsl2ShdslLineNtfyGroups	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.3
pdnHdsl2ShdslNotificationGroup	1.3.6.1.4.1.1795.2.24.2.6.23.3.2.3.1			This group supports notifications of significant conditions associated with DSL lines.

RFC description

Monitors HDSL2 and SHDSL digital subscriber line performance metrics and configuration for Paradyne devices.

Start monitoring Paradyne DSL access/transport equipment (HDSL2/G.shdsl.bis line quality) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PDN-HDSL2-SHDSL-LINE-MIB