| OID symbolic | OID numeric | Type | Access | Description |
|---|
| modVcs | 1.3.6.1.4.1.562.2.4.1.16.2 | | | |
| modVcsRowStatusTable | 1.3.6.1.4.1.562.2.4.1.16.2.1 | | not-accessible | This entry controls the addition and deletion of
modVcs components. |
| modVcsRowStatusEntry | 1.3.6.1.4.1.562.2.4.1.16.2.1.1 | | not-accessible | A single entry in the table represents a single
modVcs component. |
| ROW modVcsRowStatus | 1.3.6.1.4.1.562.2.4.1.16.2.1.1.1 | RowStatus | read-write | This variable is used as the basis for SNMP naming of
modVcs components.
These components can be added and deleted. |
| STR modVcsComponentName | 1.3.6.1.4.1.562.2.4.1.16.2.1.1.2 | DisplayString | read-only | This variable provides the component's string name for
use with the ASCII Console Interface |
| STO modVcsStorageType | 1.3.6.1.4.1.562.2.4.1.16.2.1.1.4 | StorageType | read-only | This variable represents the storage type value for the
modVcs tables. |
| NON modVcsIndex | 1.3.6.1.4.1.562.2.4.1.16.2.1.1.10 | NonReplicated | not-accessible | This variable represents the index for the modVcs tables. |
| modVcsAccOptTable | 1.3.6.1.4.1.562.2.4.1.16.2.10 | | not-accessible | Accounting information is owned by the Vc System; it is stored in
the Vc Accounting component, which itself is considered to be a
component on the switch. The Accounting Component contains a
bit map indicating which of the accounting facilities are to be
spooled in the accounting record - for example, bit '0' if set
indicates that the accounting facility with facility code H.00 should
be spooled if present in the Vc for accounting purposes. The data
contained in the Vc Accounting must be identical network wide
even though the component can be changed and upgraded on a
module by module basis. |
| modVcsAccOptEntry | 1.3.6.1.4.1.562.2.4.1.16.2.10.1 | | not-accessible | An entry in the modVcsAccOptTable. |
| INT modVcsSegmentSize | 1.3.6.1.4.1.562.2.4.1.16.2.10.1.1 | INTEGER | read-write | This attribute specifies the segment size for accounting of national
calls. Minimum allowed segment size is 1. If data segment is sent
which is less than segmentSize it is still counted as one segment. |
| INT modVcsUnitsCounted | 1.3.6.1.4.1.562.2.4.1.16.2.10.1.2 | INTEGER | read-write | This attribute specifies what is counted by frame services. If set to
frames, frames are counted, else segments are counted. |
| OCT modVcsAccountingFax | 1.3.6.1.4.1.562.2.4.1.16.2.10.1.3 | OCTET STRING | read-write | Each value corresponds to an accounting facility code, of which
there are currently 10 facility codes defined with codes H.00 to
H.09, and corresponding to the above 10 facilities.
Each of the above facilities may or may not be present and stored in
the Vc for accounting purposes, depending on the nature of the call.
For example, only those Vcs where a NUI (Network User Identifier)
is used for charging or identification purposes will have a NUI
stored in the Vc.
Description of bits:
notused0(0)
notused1(1)
originalCalledAddressFax(2) |
| INT modVcsGenerationMode | 1.3.6.1.4.1.562.2.4.1.16.2.10.1.4 | INTEGER | read-write | This attribute specifies part of the rules by which the network
generates accounting records. If set to bothEnds, then both ends of
the Vc generate accounting records. If set to singleEnd, then the
charged end of the Vc generates accounting records. In single end
generation mode, if the call does not clear gracefully, both ends of
the Vc will generate accounting record. |
| modVcsAddOptTable | 1.3.6.1.4.1.562.2.4.1.16.2.12 | | not-accessible | The Vc AddressingOptions group describes the addressing
parameters. It is currently owned by the Vc.
Most of the data contained in the Vc AddressingOptions group is
identical network wide even though the group can be changed and
upgraded on a module by module basis. |
| modVcsAddOptEntry | 1.3.6.1.4.1.562.2.4.1.16.2.12.1 | | not-accessible | An entry in the modVcsAddOptTable. |
| INT modVcsDefaultNumberingPlan | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.3 | INTEGER | read-write | This attribute specifies the numbering plan used which determines
the address format: X.121-- the international numbering plan for
public packet switched data networks or E.164-- the international
numbering plan for ISDN and PSTN.
The default numbering plan does not need to be consistent across all
of the nodes in the network. |
| INT modVcsNetworkIdType | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.4 | INTEGER | read-only | This attribute specifies whether the network uses a DNIC or INIC. It
is used by X.75 Gateways to indicate whether in network the DNIC
or INIC is used in various utilities. If it is DNIC it can be DNIC or
DCC type. If it is INIC it can be 4 digits only. |
| INT modVcsX121Type | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.5 | INTEGER | read-write | This attribute specifies whether DNIC mode or DCC mode is used
in X.121 address of international calls.
If DCC is specified, then the first 3 digits of each DNA must be the
Network ID Code.
If this attribute is changed all Dnas in the network must start with
this code. Numbering plan is affected by the change. |
| STR modVcsNetworkIdCode | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.6 | DigitString | read-write | This attribute specifies the DNIC (Data Network ID Code) of the
network or DCC code. |
| INT modVcsX121IntlAddresses | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.7 | INTEGER | read-write | This attribute indicates if any DTE is allowed to signal international
addresses. |
| U32 modVcsX121IntllPrefixDigit | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.8 | Unsigned32 | read-write | This attribute indicates the prefix digit to be used for X.121
international calls. When this digit is provided the call will have full
international address. |
| U32 modVcsX121MinAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.11 | Unsigned32 | read-write | This attribute indicates minimum length of x121 address. |
| U32 modVcsX121MaxAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.12 | Unsigned32 | read-write | This attribute indicates maximum length of x121 address. |
| INT modVcsX121ToE164EscapeSignificance | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.13 | INTEGER | read-write | This attribute specifies whether an X.121 to E.164 escape digit has
significance in selecting an X.32 (analog) or an ISDN switched
path. If two values are significant (the value 0 or the value 9) then
yes is set to this attribute. If the value of the originally entered
escape digit is not significant in routing the call then value of no is
assigned to this attribute. |
| INT modVcsE164IntlFormatAllowed | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.14 | INTEGER | read-write | This attribute indicates whether or not to allow national format
E.164 addresses. If this attribute is set to a value of Yes (=1) then
national format E.164 addresses are not allowed and international
format addresses only are allowed. If this attribute is set to a value
of No (=0), then national format E.164 addresses are allowed.
If only international format E.164 addresses are allowed, then the
'e164NatlPrefixDigit' attribute is not required, nor is the
'e164IntlPrefixDigits' required. |
| STR modVcsE164IntlPrefixDigits | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.15 | DigitString | read-write | This attribute specifies the E.164 international prefix digits. If
applicable, it is specified as 1 to 3 BCD digits.
The 3 BCD digits are stored with the length of the international
prefix in the low order nibble, nibble [0] followed by the most
significant digit of the international prefix in the next low order
nibble, nibble [1], etc.
This attribute is not required if the corresponding attribute,
'e164IntlFormatOnly' is set to a value of Yes (=1). |
| U32 modVcsE164NatlPrefixDigit | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.16 | Unsigned32 | read-write | This attribute contains the E.164 national prefix which may be
added in front of E.164 local or national call. If
e164IntlFormatOnly is set to 1, this attribute is not needed. |
| U32 modVcsE164LocalAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.17 | Unsigned32 | read-write | This attribute indicates the length of a local E.164 DNA on this
module. This attribute is not required if the corresponding attribute,
e164IntlFormatOnly is set to a value of yes.
This attribute does not need to be consistent across all of the nodes
in the network. |
| STR modVcsE164TeleCountryCode | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.18 | DigitString | read-write | This attribute specifies the E.164 Telephone Country Code (TCC)
for the country in which the network resides. If applicable, it is
specified as 1 to 3 BCD digits.
The 3 BCD digits are stored with the length of the TCC in the low
order nibble, nibble [0] followed by the most significant digit of the
TCC in the next low order nibble, nibble [1], etc. |
| U32 modVcsE164NatlMinAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.20 | Unsigned32 | read-write | This attribute indicates minimum length of e164 national address. |
| U32 modVcsE164NatlMaxAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.21 | Unsigned32 | read-write | This attribute indicates maximum length of e164 national address. |
| U32 modVcsE164IntlMinAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.22 | Unsigned32 | read-write | This attribute indicates minimum length of e164 international
address. |
| U32 modVcsE164IntlMaxAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.23 | Unsigned32 | read-write | This attribute indicates maximum length of e164 international
address. |
| U32 modVcsE164LocalMinAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.24 | Unsigned32 | read-write | This attribute indicates minimum length of e164 local address. |
| U32 modVcsE164LocalMaxAddressLength | 1.3.6.1.4.1.562.2.4.1.16.2.12.1.25 | Unsigned32 | read-write | This attribute indicates maximum length of e164 local address. |
| modVcsIntOptTable | 1.3.6.1.4.1.562.2.4.1.16.2.13 | | not-accessible | The Vc InterfaceOptions group defines Vc system parameters
common in the network. It is owned by the Vc and is considered to
be a module wide component on the switch.
The data contained in the Vc InterfaceOptions group must be
identical network wide even though this group can be changed and
upgraded on a module by module basis. |
| modVcsIntOptEntry | 1.3.6.1.4.1.562.2.4.1.16.2.13.1 | | not-accessible | An entry in the modVcsIntOptTable. |
| OCT modVcsHighPriorityPacketSizes | 1.3.6.1.4.1.562.2.4.1.16.2.13.1.1 | OCTET STRING | read-only | This attribute indicates which packet sizes are supported for high
priority calls within the network.
Description of bits:
n16(0)
n32(1)
n64(2)
n128(3)
n256(4)
n512(5)
n1024(6)
n2048(7)
n4096(8) |
| INT modVcsMaxSubnetPacketSize | 1.3.6.1.4.1.562.2.4.1.16.2.13.1.2 | INTEGER | read-write | This attribute specifies the maximum subnet packet size used for the
connections originating or terminating on this module. All modules
in the same network should have the same maxSubnetPacketSize.
If this value is not identical throughout the network, the following
points need to be considered:
a) When Passport and DPN switches are connected in the same
network, the maxSubnetPacketSize on a DPN switch can be at most
2048 and the DPN part of the network must be configured with
hardware which supports this size:
- Dedicated PE386 Network link/Trunk
- Minimum measured link speed of 256Kbits/sec
This hardware has to be present on every potential data path
between connecting end points!
b) The calling end of the connection signals the
maxSubnetPacketSize value to the called end. The called end then
compares this value to its own provisioned value and selects the
smaller value. Note that this smaller value is not signalled back to
the calling end. The calling and called ends can therefore have
different maxSubnetPacketSize values. |
| U32 modVcsCallSetupTimer | 1.3.6.1.4.1.562.2.4.1.16.2.13.1.3 | Unsigned32 | read-write | This attribute specifies the Vc callSetupTimer in units of 1 second
ticks. This timer specifies how long the Vc will wait, after sending
a subnet Call Request packet into the network, for a response from
the remote end of the Vc (in the form of a subnet Raccept packet).
If, after sending a subnet Call packet into the network, a response is
not received within this time period, the Vc will time out, clearing
the call in the assumption that the remote end is unreachable. This
timer must be long enough to take into account the time required for
routing the subnet Call Request through the Source Call Routing
and the Destination Call Routing systems in order to be delivered to
the final destination. |
| U32 modVcsCallRetryTimer | 1.3.6.1.4.1.562.2.4.1.16.2.13.1.4 | Unsigned32 | read-write | This attribute specifies, for Vc implementing Direct Calls with the
auto-call retry feature (including PVCs), the Vc callRetryTimer in
units of 1 second ticks. This timer specifies how long the Vc will
wait between unsuccessful call attempts. |
| INT modVcsDelaySubnetAcks | 1.3.6.1.4.1.562.2.4.1.16.2.13.1.5 | INTEGER | read-write | This attribute specifies delay acknowledgment timer mechanism.
If this attribute is set to no, then the Vc will automatically return
acknowledgment packets without delay. If this attribute is set to yes,
then the Vc will wait for one second in an attempt to piggyback the
acknowledgment packet on another credit or data packet. If the Vc
cannot piggyback the acknowledgment packet within this time, then
the packet is returned without piggybacking. |
| modVcsWinsTable | 1.3.6.1.4.1.562.2.4.1.16.2.213 | | not-accessible | This is the windowSize corresponding to the given packet size and
throughput class. All Vcs using the windowSize matrix support
large Vc windows on both ends of the Vc, and support the signalling
of the chosen Vc window size from the destination (called) end to
the source (calling) end. This is the only matrix supported.
The windowSize should be configured in the same way network
wide, though it can be upgraded on a module by module basis. Vcs
using the windowSize matrix will run properly if the matrices on
different nodes differ since the Vc window is selected by the
destination (called) side of the Vc. |
| modVcsWinsEntry | 1.3.6.1.4.1.562.2.4.1.16.2.213.1 | | not-accessible | An entry in the modVcsWinsTable. |
| INT modVcsWinsPktIndex | 1.3.6.1.4.1.562.2.4.1.16.2.213.1.1 | INTEGER | not-accessible | This variable represents the next to last index for the
modVcsWinsTable. |
| I32 modVcsWinsTptIndex | 1.3.6.1.4.1.562.2.4.1.16.2.213.1.2 | Integer32 | not-accessible | This variable represents the final index for the
modVcsWinsTable. |
| U32 modVcsWinsValue | 1.3.6.1.4.1.562.2.4.1.16.2.213.1.3 | Unsigned32 | read-write | This variable represents an individual value for the
modVcsWinsTable. |
| subnetInterfaceMIB | 1.3.6.1.4.1.562.2.4.2.45 | | | |
| subnetInterfaceGroup | 1.3.6.1.4.1.562.2.4.2.45.1 | | | |
| subnetInterfaceGroupBE | 1.3.6.1.4.1.562.2.4.2.45.1.5 | | | |
| subnetInterfaceGroupBE00 | 1.3.6.1.4.1.562.2.4.2.45.1.5.1 | | | |
| subnetInterfaceGroupBE00A | 1.3.6.1.4.1.562.2.4.2.45.1.5.1.2 | | | |
| subnetInterfaceCapabilities | 1.3.6.1.4.1.562.2.4.2.45.3 | | | |
| subnetInterfaceCapabilitiesBE | 1.3.6.1.4.1.562.2.4.2.45.3.5 | | | |
| subnetInterfaceCapabilitiesBE00 | 1.3.6.1.4.1.562.2.4.2.45.3.5.1 | | | |
| subnetInterfaceCapabilitiesBE00A | 1.3.6.1.4.1.562.2.4.2.45.3.5.1.2 | | | |
