Juniper-ATM-CONF

All MIBs › Juniper-ATM-CONF

Organization: Juniper Networks, Inc.

Last Updated: 2005-08-17

Category: ATM, Protocol: ATM, Vendor: Juniper

Description: Defines conformance and compliance statements for ATM interface management on Juniper Networks E-series broadband routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-ATM-CONF?

Juniper-ATM-CONF is an AGENT-CAPABILITIES module for Juniper Networks' E-series broadband routers, declaring which parts of the companion Juniper-UNI-ATM-MIB (ATM interface management) the router's SNMP agent actually implements. It defines no managed objects of its own; instead it lists capability statements mapping to ATM VCC endpoints, VP tunnels, NBMA (non-broadcast multi-access) service, and ATM switch fabric features across different agent versions. Because it is purely a conformance/capabilities declaration, it exposes no interface, environment, performance, or fault data of its own and cannot be polled for hardware or software status directly. It is entirely dependent on the Juniper-UNI-ATM-MIB (and the broader ATM MIB family) whose object support it describes. In practice it is consulted by management systems at MIB-compilation or agent-discovery time to determine which ATM features are supported by a given Juniper E-series software release, rather than used for ongoing runtime monitoring. Engineers can download the Juniper-ATM-CONF file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-ATM-CONF. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks E-series broadband routers

Monitoring Examples

This module contains no runtime data objects to poll -- it is a conformance/AGENT-CAPABILITIES module whose entries (juniAtmVccEndPointAgent, juniAtmVpTunnelAgent, juniAtmNbmaAgent, juniAtmSwitchAgent/V1/V2) merely declare which ATM MIB groups the Juniper E-series agent implements across software releases. An NMS would consult it only during MIB compilation or agent capability discovery, not for ongoing monitoring.

Imported Objects

From Juniper-Agents

juniAgents

MODULE-IDENTITY

From SNMPv2-CONF

AGENT-CAPABILITIES

From SNMPv2-SMI

MODULE-IDENTITY

OIDs

OID symbolic	OID numeric	Description
juniAtmAgent	1.3.6.1.4.1.4874.5.2.3	Juniper-UNI-ATM-MIB: The agent capabilities definitions for the ATM component of the SNMP agent in the Juniper E-series family of products.
juniAtmVccEndPointAgent	1.3.6.1.4.1.4874.5.2.3.1
juniAtmVccEndPointAgentV1	1.3.6.1.4.1.4874.5.2.3.1.1	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilities became obsolete when new objects were added to the juniAtmSubIfGroup and support for the atmfM4IfLoopbackLocationCode object was added.
juniAtmVccEndPointAgentV2	1.3.6.1.4.1.4874.5.2.3.1.2	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilities became obsolete when support was added to the Juniper-UNI-ATM-MIB for connection admission control (CAC).
juniAtmVccEndPointAgentV3	1.3.6.1.4.1.4874.5.2.3.1.3	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilities became obsolete when support was added to the Juniper-UNI-ATM-MIB for switched virtual connection (SVC).
juniAtmVccEndPointAgentV4	1.3.6.1.4.1.4874.5.2.3.1.4	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilitie became obsolete when CAC recieve bandwith and E164 public addressing objects were added.
juniAtmVccEndPointAgentV5	1.3.6.1.4.1.4874.5.2.3.1.5	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilitie became obsolete when F4 flow OAM circuits and ATM VP description objects were added to the Juniper-UNI-ATM-MIB.
juniAtmVccEndPointAgentV6	1.3.6.1.4.1.4874.5.2.3.1.6	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilitie became obsolete when ATM sub-interface location support was added to the Juniper-UNI-ATM-MIB.
juniAtmVccEndPointAgentV7	1.3.6.1.4.1.4874.5.2.3.1.7	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilitie became obsolete when support was added to export ATM sub-interface descriptions to the line cards.
juniAtmVccEndPointAgentV8	1.3.6.1.4.1.4874.5.2.3.1.8	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilities became obsolete when ATM bulk configuration profile override was introduced.
juniAtmVccEndPointAgentV9	1.3.6.1.4.1.4874.5.2.3.1.9	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilities became obsolete when ATM bulk configuration profile override was introduced.
juniAtmVccEndPointAgentV10	1.3.6.1.4.1.4874.5.2.3.1.10	The MIBs supported by the SNMP agent for the ATM application in JUNOSe.These capabilities became obsolete when ATM VP Statistics was introduced.
juniAtmVccEndPointAgentV11	1.3.6.1.4.1.4874.5.2.3.1.11	The MIBs supported by the SNMP agent for the ATM application in JUNOSe. These capabilities became obsolete when SVC support was removed.
juniAtmVccEndPointAgentV12	1.3.6.1.4.1.4874.5.2.3.1.12	The MIBs supported by the SNMP agent for the ATM application in JUNOSe.
juniAtmVpTunnelAgent	1.3.6.1.4.1.4874.5.2.3.2
juniAtmVpTunnelAgentV1	1.3.6.1.4.1.4874.5.2.3.2.1	The MIB supported by the SNMP agent for the ATM application in JUNOSe.
juniAtmNbmaAgent	1.3.6.1.4.1.4874.5.2.3.3
juniAtmNbmaAgentV1	1.3.6.1.4.1.4874.5.2.3.3.1	The MIB supported by the SNMP agent for the ATM application in JUNOSe.
juniAtmSwitchAgent	1.3.6.1.4.1.4874.5.2.3.4
juniAtmSwitchAgentV1	1.3.6.1.4.1.4874.5.2.3.4.1
juniAtmSwitchAgentV2	1.3.6.1.4.1.4874.5.2.3.4.2
juniAtmTrafficShapingAgent	1.3.6.1.4.1.4874.5.2.3.5
juniAtmTrafficShapingAgentV1	1.3.6.1.4.1.4874.5.2.3.5.1	The MIB supported by the SNMP agent for the ATM application in JUNOSe.

RFC description

Documents SNMP agent capabilities for ATM management in Juniper E-series routers. Specifies ATM circuit, VCC, and OAM support across JUNOSe versions.

Start monitoring Juniper Networks E-series broadband router (agent capabilities, ATM) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-ATM-CONF

What Is Juniper-ATM-CONF?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description