NB30MIB

All MIBs › NB30MIB

Category: Cisco Aironet / Wireless

Description: Manages NB30 device configuration, interfaces, and basic system status objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NB30MIB?

NB30MIB is a vendor-specific MIB (apparently from a bridge/router equipment maker, based on the "nb30" naming and bridging/DSX objects) managing NB30 device configuration, interfaces, and basic system status. It belongs to the WAN/bridge networking technology area, covering bridging and DSX (digital signal cross-connect) circuit interfaces. It exposes device-level identity and control objects (bridge name, port count, device type/version, location), bridge frame-forwarding/receive counters, and DSX channel objects, plus operations to disable or restart the bridge and restore settings. Its monitoring value spans both software and traffic status: nb30DeviceStatus reports overall device operational status, nb30DeviceVersion identifies firmware, and nb30DeviceFrFwds/nb30DeviceFrRxs track bridge frame forwarding/reception performance counters, together letting an admin confirm the bridge is up, running the expected version, and passing traffic. It is a self-contained enterprise MIB with an internal dependency structure between its device, bridge, and DSX/channel object groups. It's typically deployed on WAN bridge/DSX interface equipment used to interconnect LAN segments over digital circuits. Engineers can download the NB30MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in NB30MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

NB30 bridge/DSX WAN interconnect device

Monitoring Examples

An administrator would poll nb30DeviceStatus and nb30DeviceType to confirm the unit is operational and identify its hardware type, while nb30DeviceFrFwds and nb30DeviceFrRxs give bridge frame forwarding and receive counts useful for spotting a stalled or congested bridge link. The nb30DeviceNumPorts and nb30DeviceBdgName objects identify the bridge's port count and configured name, and nb30DeviceVersion would be checked after a firmware update to confirm the new version took effect. Falling nb30DeviceFrFwds/nb30DeviceFrRxs counters on an otherwise-up device would point to a bridging or DSX channel problem rather than a device outage.

What Can Be Monitored

device operational status
hardware/firmware version
bridge frame forward/receive counters
port count and bridge name
DSX channel configuration

Imported Objects

From IRM-OIDS

nb30Rev1

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter

OIDs

OID symbolic	OID numeric	Type	Access	Description
nb30Device	1.3.6.1.4.1.52.1.6.12.1
INT nb30DeviceDisableBdg	1.3.6.1.4.1.52.1.6.12.1.1	INTEGER	read-write	Indicates if the bridge will be disabled.
INT nb30DeviceRestoreSettings	1.3.6.1.4.1.52.1.6.12.1.2	INTEGER	read-write	Restore the following settings to their default values: Bridge Name to CABLETRON REMOTE BRIDGE, Location to LOCAL, Enet Port 1 Name to ETHERNET PORT 1, Enet Port 2 Name to ETHERNET PORT 2, Remote Port Name to REMOTE PORT, Enet Port 1 Network Name to LAN_1, Enet Port 2 Network Name to LAN_2, Defualt Enet Port to Port 1, Enable Redundancy to NO, Port 1 and Port 2 Poll Address to 00-00-00-00-00-00, Port 1 and Port 2 Poll Interval to 5 Seconds, Port 1 and Port 2 Max Retries to 6, Remote Port Network Name to REMOTE LINK, Ageing Time for Acquired Database to 300 seconds, Place seventeen default multicast addresses into the permanent and acquired databases, Type of Spanning Tree to 802.1, Type of Filtering to IEEE 802.1, Bridge Max Age to 20 seconds, Bridge Forward Delay to 15 seconds, Bridge Hello Time to 2 seconds, Bridge Priority to 8000, Port 1 Priority to 80, Port 2 Priority to 80, Port 1 Path Cost to 1000, Port 2 Path Cost to 1000, Number of Restarts to 0.
OCT nb30DeviceBdgName	1.3.6.1.4.1.52.1.6.12.1.3	OCTET STRING	read-write	The user-defined name (up to 32 characters long) of the bridge. The default bridge name is CABLETRON REMOTE BRIDGE.
INT nb30DeviceNumPorts	1.3.6.1.4.1.52.1.6.12.1.4	INTEGER	read-only	The number of ports present on the bridge.
OCT nb30DeviceType	1.3.6.1.4.1.52.1.6.12.1.5	OCTET STRING	read-only	The type of bridge, NB30.
OCT nb30DeviceVersion	1.3.6.1.4.1.52.1.6.12.1.6	OCTET STRING	read-only	The release version of the firmware installed in the bridge.
OCT nb30DeviceLocation	1.3.6.1.4.1.52.1.6.12.1.7	OCTET STRING	read-write	The user-defined name (up to 14 characters long) to indicate the location of the bridge on the network. The default location name is LOCAL.
OCT nb30DeviceStatus	1.3.6.1.4.1.52.1.6.12.1.8	OCTET STRING	read-only	The status of the bridge, ON-LINE, STAND BY or DISABLED.
INT nb30DeviceRestartBdg	1.3.6.1.4.1.52.1.6.12.1.9	INTEGER	read-write	Force the bridge to undergo a software reset.
CTR nb30DeviceFrFwds	1.3.6.1.4.1.52.1.6.12.1.10	Counter	read-only	The number of frames forwarded by the bridge.
CTR nb30DeviceFrRxs	1.3.6.1.4.1.52.1.6.12.1.11	Counter	read-only	The number of frames received by the bridge.
CTR nb30DeviceFrFlts	1.3.6.1.4.1.52.1.6.12.1.12	Counter	read-only	The number of frames filtered by the bridge.
CTR nb30DeviceErrs	1.3.6.1.4.1.52.1.6.12.1.13	Counter	read-only	The total number of network errors that have occurred.
CTR nb30DeviceNumRestarts	1.3.6.1.4.1.52.1.6.12.1.14	Counter	read-only	The number of times the bridge has been powered up or restarted.
INT nb30DeviceTypeFiltering	1.3.6.1.4.1.52.1.6.12.1.15	INTEGER	read-write	The type of filtering to be performed by the bridge. The default is IEEE 802.1.
INT nb30DeviceSTAProtocol	1.3.6.1.4.1.52.1.6.12.1.16	INTEGER	read-write	The spanning tree algorithm under which the bridge is operating. The selections are as follows: - IEEE 802.1 compliant spanning tree algorithm environment (802.1) - DEC LAN Bridge 100 environment (DEC) - Without the spanning tree algorithm enabled (NONE) The default is 802.1.
OCT nb30DeviceBridgeID	1.3.6.1.4.1.52.1.6.12.1.17	OCTET STRING	read-only	The unique identifier of the bridge. The first two bytes of the identifier are the bridge priority and the last six bytes are the Ethernet address.
CTR nb30DeviceTopChgCnts	1.3.6.1.4.1.52.1.6.12.1.18	Counter	read-only	The number of times the bridge's Topology Change Flag has been changed since the bridge was powered up or initialized.
INT nb30DeviceTimeTopChg	1.3.6.1.4.1.52.1.6.12.1.19	INTEGER	read-only	The time in seconds that has elapsed since the bridge's Topology Change Flag last recorded the value of a topology change.
INT nb30DeviceTopChg	1.3.6.1.4.1.52.1.6.12.1.20	INTEGER	read-only	Indicates if a bridge topology change is in progress.
INT nb30DeviceRootCost	1.3.6.1.4.1.52.1.6.12.1.21	INTEGER	read-only	The cost of the path to the root from this bridge.
INT nb30DeviceRootPort	1.3.6.1.4.1.52.1.6.12.1.22	INTEGER	read-only	The port identifier for the port which offers the lowest cost path to the root, i.e. that port for which the sum of the values of the designated cost and path cost parameters held for the port is lowest.
OCT nb30DeviceDesigRoot	1.3.6.1.4.1.52.1.6.12.1.23	OCTET STRING	read-only	The unique identifier of the bridge recorded as the root.
INT nb30DeviceMaxAge	1.3.6.1.4.1.52.1.6.12.1.24	INTEGER	read-only	The maximum age of received protocol information before it is discarded.
INT nb30DeviceHoldTime	1.3.6.1.4.1.52.1.6.12.1.25	INTEGER	read-only	The minimum time period elapsing between the transmission of configuration BPDU's through a given bridge port.
INT nb30DeviceFwdDly	1.3.6.1.4.1.52.1.6.12.1.26	INTEGER	read-only	The time spent in the listening state while moving from the blocking state to the learning state, or the time spent in the learning state while moving from the listening state to the forwarding state.
INT nb30DeviceHelloTime	1.3.6.1.4.1.52.1.6.12.1.27	INTEGER	read-only	The time interval between the transmission of Configuration BPDU's by a bridge which is attempting to become the root or is the root.
INT nb30DeviceBdgFwdDly	1.3.6.1.4.1.52.1.6.12.1.28	INTEGER	read-write	The value of the forward delay parameter when the bridge is the root or is attempting to become the root. A time of 4 to 30 seconds is allowed. The default is 15 seconds.
INT nb30DeviceBdgMaxAge	1.3.6.1.4.1.52.1.6.12.1.29	INTEGER	read-write	The value of the Max Age parameter when the bridge is the root or is attempting to become the root. A time of 6 to 40 seconds is allowed. The default is 20 seconds.
INT nb30DeviceBdgHello	1.3.6.1.4.1.52.1.6.12.1.30	INTEGER	read-write	The value of the Hello Time parameter when the bridge is the root or is attempting to become the root. A time of 1 to 10 seconds is allowed. The default is 2 seconds.
INT nb30DeviceBdgPriority	1.3.6.1.4.1.52.1.6.12.1.31	INTEGER	read-write	Used in the spanning tree for priority comparisons. Allowed range is 0 through FFFF. The default is 8000.
INT nb30DeviceResetCounts	1.3.6.1.4.1.52.1.6.12.1.32	INTEGER	read-write	Reset all counters to zero.
INT nb30DeviceUptime	1.3.6.1.4.1.52.1.6.12.1.33	INTEGER	read-only	The time, in seconds, that has elapsed since the bridge was last reset or initialized.
INT nb30DeviceRootSwitch	1.3.6.1.4.1.52.1.6.12.1.34	INTEGER	read-only	The status of the Root switch on the front panel of the NB30.
INT nb30DeviceFwdBroadcast	1.3.6.1.4.1.52.1.6.12.1.35	INTEGER	read-only	The status of the Forward Broadcast switch on the front panel of the NB30.
INT nb30DeviceConfigSw1	1.3.6.1.4.1.52.1.6.12.1.36	INTEGER	read-only	The status of Config switch 1 on the back panel of the NB30.
INT nb30DeviceConfigSw2	1.3.6.1.4.1.52.1.6.12.1.37	INTEGER	read-only	The status of Config switch 2 on the back panel of the NB30.
INT nb30DeviceConfigSw3	1.3.6.1.4.1.52.1.6.12.1.38	INTEGER	read-only	The status of Config switch 3 on the back panel of the NB30.
INT nb30DeviceConfigSw4	1.3.6.1.4.1.52.1.6.12.1.39	INTEGER	read-only	The status of Config switch 4 on the back panel of the NB30.
INT nb30DevicePortActive	1.3.6.1.4.1.52.1.6.12.1.40	INTEGER	read-only	The Port number which is acting as the online Ethernet Port on the NB30.
INT nb30DeviceDefPort	1.3.6.1.4.1.52.1.6.12.1.41	INTEGER	read-write	The Port number which is Default Ethernet Port on the NB30 at power up.
INT nb30DeviceRedEnable	1.3.6.1.4.1.52.1.6.12.1.42	INTEGER	read-write	The state of the Redundancy Enable Flag.
nb30Dsx	1.3.6.1.4.1.52.1.6.12.2
INT nb30DsxLoopUp	1.3.6.1.4.1.52.1.6.12.2.1	INTEGER	read-write	The loop up command for the DSX-1 Remote Interface.
INT nb30DsxLoopDn	1.3.6.1.4.1.52.1.6.12.2.2	INTEGER	read-write	The loop down command for the DSX-1 Remote Interface.
INT nb30DsxLoopSt	1.3.6.1.4.1.52.1.6.12.2.3	INTEGER	read-only	The loop status for the DSX-1 Remote Interface.
INT nb30DsxLoopPattern	1.3.6.1.4.1.52.1.6.12.2.4	INTEGER	read-write	The loop test pattern for the DSX-1 Remote Interface.
nb30DsxChannel	1.3.6.1.4.1.52.1.6.12.3
nb30DsxChannelTable	1.3.6.1.4.1.52.1.6.12.3.1		not-accessible	NB30 DSX-1 Remote Port Channelization Table
nb30DsxEntry	1.3.6.1.4.1.52.1.6.12.3.1.1		not-accessible
INT nb30DsxChannelControl	1.3.6.1.4.1.52.1.6.12.3.1.1.1	INTEGER	read-write	Disable the DSX-1 Channel.
INT nb30DsxChannelId	1.3.6.1.4.1.52.1.6.12.3.1.1.2	INTEGER	read-write	The channel number for this entry.
nb30Port	1.3.6.1.4.1.52.1.6.12.4
nb30PortTable	1.3.6.1.4.1.52.1.6.12.4.1		not-accessible	Bridge Port information table
nb30PortEntry	1.3.6.1.4.1.52.1.6.12.4.1.1		not-accessible
OCT nb30PortAddress	1.3.6.1.4.1.52.1.6.12.4.1.1.1	OCTET STRING	read-only	The Ethernet address of the port. Instance of 1 represents the local Ethernet address, instance of 2 represents the remote Ethernet address.
OCT nb30PortName	1.3.6.1.4.1.52.1.6.12.4.1.1.2	OCTET STRING	read-write	The user-defined name (up to 32 characters long) assigned to the port. The default Enet port 1 name is ETHERNET PORT 1 and the default Enet Port 2 name is ETHERNET PORT 2.
OCT nb30PortType	1.3.6.1.4.1.52.1.6.12.4.1.1.3	OCTET STRING	read-only	The IEEE specification the port meets, e.g. 802.3.
OCT nb30PortStatus	1.3.6.1.4.1.52.1.6.12.4.1.1.4	OCTET STRING	read-only	The status in which the port is operating. The status messages for Ports 1 and 2 are: OFF - The port is off, due to a failed network interface chip associated with that port. OK/SQE ON - The port is communicating with the network and the transceiver making the connection to the network has SQE enabled. OK/SQE OFF - The port is communicating with the network and the transceiver making the connection to the network has SQE disabled. CARRIER LOST - Communication with the network has not been established or has been lost.
OCT nb30PortNetName	1.3.6.1.4.1.52.1.6.12.4.1.1.5	OCTET STRING	read-write	The user-defined name (up to 32 characters long) assigned to a network segment connected to the port. The default network name for Port 1 is LAN_1 and the default network name for Port 2 is LAN_2.
CTR nb30PortFrRxs	1.3.6.1.4.1.52.1.6.12.4.1.1.6	Counter	read-only	The number of frames received at the specified port.
CTR nb30PortDisInbounds	1.3.6.1.4.1.52.1.6.12.4.1.1.7	Counter	read-only	The total number of valid frames that were received at the port but then discarded by the bridge in the forwarding process.
CTR nb30PortFwdOutbs	1.3.6.1.4.1.52.1.6.12.4.1.1.8	Counter	read-only	The number of frames forwarded successfully to the appropriate port.
CTR nb30PortDisLOBs	1.3.6.1.4.1.52.1.6.12.4.1.1.9	Counter	read-only	The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data.
CTR nb30PortDisTDEs	1.3.6.1.4.1.52.1.6.12.4.1.1.10	Counter	read-only	The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was possible.
CTR nb30PortCollisions	1.3.6.1.4.1.52.1.6.12.4.1.1.11	Counter	read-only	The number of collisions that have occurred on the network at the specified port.
CTR nb30PortTxAborts	1.3.6.1.4.1.52.1.6.12.4.1.1.12	Counter	read-only	The number of transmissions that have been aborted due to excessive collisions (over 16 attempts to transmit the same packet).
CTR nb30PortOowCollisions	1.3.6.1.4.1.52.1.6.12.4.1.1.13	Counter	read-only	The number of collisions out of the standard collision window (51.2 uS). This indicates a network problem.
CTR nb30PortCRCErrs	1.3.6.1.4.1.52.1.6.12.4.1.1.14	Counter	read-only	The number of packets detected with Cyclical Redundancy Check failures.
CTR nb30PortFrAlignErrs	1.3.6.1.4.1.52.1.6.12.4.1.1.15	Counter	read-only	The number of errors due to misaligned packets.
INT nb30PortPriority	1.3.6.1.4.1.52.1.6.12.4.1.1.16	INTEGER	read-write	The part of the port identifier which is used with the spanning tree algorithm when determining which port in a LAN segment has priority. The default is 80. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
OCT nb30PortState	1.3.6.1.4.1.52.1.6.12.4.1.1.17	OCTET STRING	read-only	The current state of the port, DISABLED, LISTENING, LEARNING, FORWARDING or BLOCKING. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
INT nb30PortPathCost	1.3.6.1.4.1.52.1.6.12.4.1.1.18	INTEGER	read-write	The contributory cost of the applicable port to the overall cost of the path when the specified port is the root port. Allowable range is 1 to 65535. The default is 1000. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
INT nb30PortDesigCost	1.3.6.1.4.1.52.1.6.12.4.1.1.19	INTEGER	read-only	The cost of the path of this port to the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
OCT nb30PortDesigBrdg	1.3.6.1.4.1.52.1.6.12.4.1.1.20	OCTET STRING	read-only	The network address of the bridge that is assumed to be the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
INT nb30PortDesigPort	1.3.6.1.4.1.52.1.6.12.4.1.1.21	INTEGER	read-only	The port identifier of the bridge port believed to be the designated port for the LAN associated with the port. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
INT nb30PortTopChgAck	1.3.6.1.4.1.52.1.6.12.4.1.1.22	INTEGER	read-only	The value of the topology change acknowledgement flag in the next configuration BPDU to be transmitted on the associated port. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
OCT nb30PortDesigRoot	1.3.6.1.4.1.52.1.6.12.4.1.1.23	OCTET STRING	read-only	The unique bridge identifier of the bridge that is assumed to be the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port.
CTR nb30PortOversizePkts	1.3.6.1.4.1.52.1.6.12.4.1.1.24	Counter	read-only	The number of packets received at the indicated NB30 Port that were greater than the IEEE 802.3 maximum Ethernet frame size of 1518 bytes.
CTR nb30PortFrFiltereds	1.3.6.1.4.1.52.1.6.12.4.1.1.25	Counter	read-only	The number of frames received at the indicated port that were filtered by the bridge.
OCT nb30PortPollAddress	1.3.6.1.4.1.52.1.6.12.4.1.1.26	OCTET STRING	read-write	The Poll Address that will be used by the Redundant Port Algorithm on the NB30.
INT nb30PortPollInterval	1.3.6.1.4.1.52.1.6.12.4.1.1.27	INTEGER	read-write	The Poll Interval used by the Redundant Port Algorithm on the NB30. Valid range is 1 - 30 seconds.
INT nb30PortMaxRetry	1.3.6.1.4.1.52.1.6.12.4.1.1.28	INTEGER	read-write	The Max number of retries for the Redundant Port Algorithm on the NB30. Valid range is 2 - 99 retries
INT nb30PortId	1.3.6.1.4.1.52.1.6.12.4.1.1.29	INTEGER	read-only	The port number for this entry.
nb30RemPort	1.3.6.1.4.1.52.1.6.12.5
nb30RemPortTable	1.3.6.1.4.1.52.1.6.12.5.1		not-accessible	Bridge Remote Port information table
nb30RemPortEntry	1.3.6.1.4.1.52.1.6.12.5.1.1		not-accessible
OCT nb30RemPortName	1.3.6.1.4.1.52.1.6.12.5.1.1.1	OCTET STRING	read-write	The user-defined name assigned to the remote port. The default Remote port name is REMOTE PORT.
OCT nb30RemPortType	1.3.6.1.4.1.52.1.6.12.5.1.1.2	OCTET STRING	read-only	The Electrical interface specification the port meets, e.g. DSX-1, V.35.
OCT nb30RemPortStatus	1.3.6.1.4.1.52.1.6.12.5.1.1.3	OCTET STRING	read-only	The status in which the remote port is operating. The status messages for the Remote Port are: NO EXT CLOCK DCE NOT READY / NO DM DCE NOT READY / NO CTS LINK OK / DCE READY NET LOOP / RED ALARM REM LOOP / RED ALARM NORMAL / RED ALARM NET LOOP / YELLOW ALARM REM LOOP / YELLOW ALARM NORMAL / YELLOW ALARM NET LOOP / LINK OK REM LOOP / LINK OK NORMAL / LINK OK NET LOOP / LINK LOST REM LOOP / LINK LOST NORMAL / LINK LOST
OCT nb30RemPortNetName	1.3.6.1.4.1.52.1.6.12.5.1.1.4	OCTET STRING	read-write	The user-defined name assigned to a wide area segment connected to the remote port. The default network name for Remote Port is REMOTE LINK.
CTR nb30RemPortFrRxs	1.3.6.1.4.1.52.1.6.12.5.1.1.5	Counter	read-only	The number of frames received at the remote port.
CTR nb30RemPortFwdOutbs	1.3.6.1.4.1.52.1.6.12.5.1.1.6	Counter	read-only	The number of frames forwarded successfully to the remote port.
CTR nb30RemPortDisLOBs	1.3.6.1.4.1.52.1.6.12.5.1.1.7	Counter	read-only	The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data.
CTR nb30RemPortDisTDEs	1.3.6.1.4.1.52.1.6.12.5.1.1.8	Counter	read-only	The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was possible.
CTR nb30RemPortCRCErrs	1.3.6.1.4.1.52.1.6.12.5.1.1.9	Counter	read-only	The number of packets detected with Cyclical Redundancy Check failures.
CTR nb30RemPortFrAlErrs	1.3.6.1.4.1.52.1.6.12.5.1.1.10	Counter	read-only	The number of errors due to misaligned packets.
INT nb30RemPortId	1.3.6.1.4.1.52.1.6.12.5.1.1.11	INTEGER	read-only	The remote port ID, there is only a single port which is identified as 0.
nb30FilterDB	1.3.6.1.4.1.52.1.6.12.6
nb30AcqDB	1.3.6.1.4.1.52.1.6.12.6.1
INT nb30AcqTotalEntries	1.3.6.1.4.1.52.1.6.12.6.1.1	INTEGER	read-only	The total number of entries in the acquired database.
INT nb30AcqMaxEntries	1.3.6.1.4.1.52.1.6.12.6.1.2	INTEGER	read-only	The maximum number of entries allowed in the acquired database 8191 entries.
INT nb30AcqStaticEntries	1.3.6.1.4.1.52.1.6.12.6.1.3	INTEGER	read-only	The number of addresses added to the Acquired database by the user or network manager.
INT nb30AcqDynamicEntries	1.3.6.1.4.1.52.1.6.12.6.1.4	INTEGER	read-only	The number of entries that have been accumulated in the Acquired database through the bridge's learning process.
INT nb30AcqDynAgeTime	1.3.6.1.4.1.52.1.6.12.6.1.5	INTEGER	read-write	The length of time allowed for a dynamic entry in the acquired database to be inactive before it is dropped from the database. A time from 10 - 1,000,000 seconds is allowed. The default is 300 seconds.
INT nb30AcqEraseDatabase	1.3.6.1.4.1.52.1.6.12.6.1.6	INTEGER	read-write	Set to one to erase all entries in the acquired database.
nb30AcqDBTable	1.3.6.1.4.1.52.1.6.12.6.1.7		not-accessible	Aquired database entrys table
nb30AcqDBEntry	1.3.6.1.4.1.52.1.6.12.6.1.7.1		not-accessible
INT nb30AcqCreateFilter	1.3.6.1.4.1.52.1.6.12.6.1.7.1.1	INTEGER	read-write	Add an entry to the acquired database to filter packets entering port 1 if those packets are destined for the specified address.
INT nb30AcqCreateForward	1.3.6.1.4.1.52.1.6.12.6.1.7.1.2	INTEGER	read-write	Add an entry to the acquired database to forward packets entering port 1 to the remote port if those packets are destined for the specified address.
INT nb30AcqDeleteFilter	1.3.6.1.4.1.52.1.6.12.6.1.7.1.3	INTEGER	read-write	Delete an entry from the acquired database.
OCT nb30AcqFilterType	1.3.6.1.4.1.52.1.6.12.6.1.7.1.4	OCTET STRING	read-only	Display the entry type, STATIC or DYNAMIC.
INT nb30AcqFilterAction	1.3.6.1.4.1.52.1.6.12.6.1.7.1.5	INTEGER	read-only	The action to be taken for packets entering port 1.
OCT nb30AcqSourceAddress	1.3.6.1.4.1.52.1.6.12.6.1.7.1.6	OCTET STRING	read-only	The source address of this acquired database entry, i.e. the instance.
OCT nb30AcqMacAddress	1.3.6.1.4.1.52.1.6.12.6.1.7.1.7	OCTET STRING	read-only	The MAC address for the specific entry.
nb30PermDB	1.3.6.1.4.1.52.1.6.12.6.2
INT nb30PermMaxEntries	1.3.6.1.4.1.52.1.6.12.6.2.1	INTEGER	read-only	The maximum number of entries allowed in the permanent database 2047 entries.
INT nb30PermCurrentEntries	1.3.6.1.4.1.52.1.6.12.6.2.2	INTEGER	read-only	The number of entries currently recorded in the bridge's permanent database.
INT nb30PermEraseDatabase	1.3.6.1.4.1.52.1.6.12.6.2.3	INTEGER	read-write	Erase all entries in the permanent database.
nb30PermDBTable	1.3.6.1.4.1.52.1.6.12.6.2.4		not-accessible	Aquired database entrys table
nb30PermDBEntry	1.3.6.1.4.1.52.1.6.12.6.2.4.1		not-accessible
INT nb30PermCreateFilter	1.3.6.1.4.1.52.1.6.12.6.2.4.1.1	INTEGER	read-write	Add an entry to the permanent database to filter packets entering port 1 if those packets are destined for the specified address.
INT nb30PermCreateForward	1.3.6.1.4.1.52.1.6.12.6.2.4.1.2	INTEGER	read-write	Add an entry to the permanent database to forward packets entering port 1 to the remote port if those packets are destined for the specified address.
INT nb30PermDeleteEntry	1.3.6.1.4.1.52.1.6.12.6.2.4.1.3	INTEGER	read-write	Delete an entry from the permanent database.
OCT nb30PermFilterType	1.3.6.1.4.1.52.1.6.12.6.2.4.1.4	OCTET STRING	read-only	Display the entry type, STATIC .
INT nb30PermFilterAction	1.3.6.1.4.1.52.1.6.12.6.2.4.1.5	INTEGER	read-only	The action taken on packets entering port 1.
OCT nb30PermSourceAddress	1.3.6.1.4.1.52.1.6.12.6.2.4.1.6	OCTET STRING	read-only	The source address in this permanent database entry, i.e. the instance.
OCT nb30PermDBMacAddress	1.3.6.1.4.1.52.1.6.12.6.2.4.1.7	OCTET STRING	read-only	The specific MAC address for this entry.
nb30SpecDB	1.3.6.1.4.1.52.1.6.12.6.3
INT nb30SpecNumEntries	1.3.6.1.4.1.52.1.6.12.6.3.1	INTEGER	read-only	The number of filters in the special database.
INT nb30SpecMaxEntries	1.3.6.1.4.1.52.1.6.12.6.3.2	INTEGER	read-only	The maximum number of filters the special database can contain.
INT nb30SpecNextFilterNum	1.3.6.1.4.1.52.1.6.12.6.3.3	INTEGER	read-only	The number of the next available filter that can be added to the special database. This OID will return a 255 if the database is full
nb30SpecDBTable	1.3.6.1.4.1.52.1.6.12.6.3.4		not-accessible
nb30SpecDBEntry	1.3.6.1.4.1.52.1.6.12.6.3.4.1		not-accessible
INT nb30SpecEnable	1.3.6.1.4.1.52.1.6.12.6.3.4.1.1	INTEGER	read-write	Enable or disable the filter.
INT nb30SpecPort1	1.3.6.1.4.1.52.1.6.12.6.3.4.1.2	INTEGER	read-write	Set port 1 to filter or forward packets.
OCT nb30SpecDestAddress	1.3.6.1.4.1.52.1.6.12.6.3.4.1.3	OCTET STRING	read-write	Set the special database to filter packets with a specific destination address.
OCT nb30SpecSrcAddress	1.3.6.1.4.1.52.1.6.12.6.3.4.1.4	OCTET STRING	read-write	Set the special database to filter packets with a specific source address.
OCT nb30SpecType	1.3.6.1.4.1.52.1.6.12.6.3.4.1.5	OCTET STRING	read-write	Set the special database to filter packets with a specific type field.
OCT nb30SpecDataField	1.3.6.1.4.1.52.1.6.12.6.3.4.1.6	OCTET STRING	read-write	Set the special database to filter packets based on the first sixteen bytes of data in the packet.
INT nb30SpecDeleteFilter	1.3.6.1.4.1.52.1.6.12.6.3.4.1.7	INTEGER	read-write	Delete a filter from the special database.
INT nb30SpecDbFilterNumber	1.3.6.1.4.1.52.1.6.12.6.3.4.1.8	INTEGER	read-only	The specific special data base filter number.

RFC description

Cabletron NB30 remote bridge management for MAC address filtering and bridging control.

Start monitoring NB30 bridge/DSX WAN interconnect device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NB30MIB

What Is NB30MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

RFC description