NB30MIB DEFINITIONS ::= BEGIN -- nb30_mib.txt -- Revision: 01.02.01 -- Part Number: 2170992 -- Date: April 18, 1997 -- Cabletron Systems, Inc. -- 35 Industrial Way, P.O. Box 5005 -- Rochester, NH 03867-0505 -- (603) 332-9400 -- support@ctron.com -- This module provides authoritative definitions for Cabletron's -- Management Information Base For the Remote Bridge (NB30) -- -- This module will be extended, as required. -- -- Cabletron Systems reserves the right to make changes in -- specification and other information contained in this document -- without prior notice. The reader should consult Cabletron Systems -- to determine whether any such changes have been made. -- -- In no event shall Cabletron Systems be liable for any incidental, -- indirect, special, or consequential damages whatsoever (including -- but not limited to lost profits) arising out of or related to this -- document or the information contained in it, even if Cabletron -- Systems has been advised of, known, or should have known, the -- possibility of such damages. -- -- Cabletron grants vendors, end-users, and other interested parties -- a non-exclusive license to use this Specification in connection -- with the management of Cabletron products. -- Copyright (c)1996 Cabletron Systems IMPORTS OBJECT-TYPE FROM RFC-1212 Counter FROM RFC1155-SMI nb30Rev1 FROM IRM-OIDS; nb30Device OBJECT IDENTIFIER ::= { nb30Rev1 1 } nb30Dsx OBJECT IDENTIFIER ::= { nb30Rev1 2 } nb30DsxChannel OBJECT IDENTIFIER ::= { nb30Rev1 3 } nb30Port OBJECT IDENTIFIER ::= { nb30Rev1 4 } nb30RemPort OBJECT IDENTIFIER ::= { nb30Rev1 5 } nb30FilterDB OBJECT IDENTIFIER ::= { nb30Rev1 6 } nb30AcqDB OBJECT IDENTIFIER ::= { nb30FilterDB 1 } nb30PermDB OBJECT IDENTIFIER ::= { nb30FilterDB 2 } nb30SpecDB OBJECT IDENTIFIER ::= { nb30FilterDB 3 } -- Device Object Definitions -- -- This section defines the objects under the Device node. -- -- Instance Identifiers for Device Objects -- -- There is only one instance of a Device object, thus the Instance -- Identifier is 0. -- -- Device Objects nb30DeviceDisableBdg OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.1 SYNTAX INTEGER { disableBridge(2), enableBridge(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates if the bridge will be disabled." ::= { nb30Device 1 } nb30DeviceRestoreSettings OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.2 SYNTAX INTEGER { restoreSettings(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Restore the following settings to their default values: Bridge Name to CABLETRON REMOTE BRIDGE, Location to LOCAL, Enet Port 1 Name to ETHERNET PORT 1, Enet Port 2 Name to ETHERNET PORT 2, Remote Port Name to REMOTE PORT, Enet Port 1 Network Name to LAN_1, Enet Port 2 Network Name to LAN_2, Defualt Enet Port to Port 1, Enable Redundancy to NO, Port 1 and Port 2 Poll Address to 00-00-00-00-00-00, Port 1 and Port 2 Poll Interval to 5 Seconds, Port 1 and Port 2 Max Retries to 6, Remote Port Network Name to REMOTE LINK, Ageing Time for Acquired Database to 300 seconds, Place seventeen default multicast addresses into the permanent and acquired databases, Type of Spanning Tree to 802.1, Type of Filtering to IEEE 802.1, Bridge Max Age to 20 seconds, Bridge Forward Delay to 15 seconds, Bridge Hello Time to 2 seconds, Bridge Priority to 8000, Port 1 Priority to 80, Port 2 Priority to 80, Port 1 Path Cost to 1000, Port 2 Path Cost to 1000, Number of Restarts to 0." ::= { nb30Device 2 } nb30DeviceBdgName OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.3 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The user-defined name (up to 32 characters long) of the bridge. The default bridge name is CABLETRON REMOTE BRIDGE." ::= { nb30Device 3 } nb30DeviceNumPorts OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.4 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of ports present on the bridge." ::= { nb30Device 4 } nb30DeviceType OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.5 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The type of bridge, NB30." ::= { nb30Device 5 } nb30DeviceVersion OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.6 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The release version of the firmware installed in the bridge." ::= { nb30Device 6 } nb30DeviceLocation OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.7 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The user-defined name (up to 14 characters long) to indicate the location of the bridge on the network. The default location name is LOCAL." ::= { nb30Device 7 } nb30DeviceStatus OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.8 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The status of the bridge, ON-LINE, STAND BY or DISABLED." ::= { nb30Device 8 } nb30DeviceRestartBdg OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.9 SYNTAX INTEGER { restartBridge(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Force the bridge to undergo a software reset." ::= { nb30Device 9 } nb30DeviceFrFwds OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.10 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames forwarded by the bridge." ::= { nb30Device 10 } nb30DeviceFrRxs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.11 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received by the bridge." ::= { nb30Device 11 } nb30DeviceFrFlts OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.12 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames filtered by the bridge." ::= { nb30Device 12 } nb30DeviceErrs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.13 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of network errors that have occurred." ::= { nb30Device 13 } nb30DeviceNumRestarts OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.14 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times the bridge has been powered up or restarted." ::= { nb30Device 14 } nb30DeviceTypeFiltering OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.15 SYNTAX INTEGER { ieee8021(1), specialDB(2), both(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of filtering to be performed by the bridge. The default is IEEE 802.1." ::= { nb30Device 15 } nb30DeviceSTAProtocol OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.16 SYNTAX INTEGER { ieee8021(1), dec(2), none(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The spanning tree algorithm under which the bridge is operating. The selections are as follows: - IEEE 802.1 compliant spanning tree algorithm environment (802.1) - DEC LAN Bridge 100 environment (DEC) - Without the spanning tree algorithm enabled (NONE) The default is 802.1." ::= { nb30Device 16 } nb30DeviceBridgeID OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.17 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The unique identifier of the bridge. The first two bytes of the identifier are the bridge priority and the last six bytes are the Ethernet address." ::= { nb30Device 17 } nb30DeviceTopChgCnts OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.18 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times the bridge's Topology Change Flag has been changed since the bridge was powered up or initialized." ::= { nb30Device 18 } nb30DeviceTimeTopChg OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.19 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The time in seconds that has elapsed since the bridge's Topology Change Flag last recorded the value of a topology change." ::= { nb30Device 19 } nb30DeviceTopChg OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.20 SYNTAX INTEGER { noTopologyChangeInProgress(1), topologyChangeInProgress(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates if a bridge topology change is in progress." ::= { nb30Device 20 } nb30DeviceRootCost OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.21 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The cost of the path to the root from this bridge." ::= { nb30Device 21 } nb30DeviceRootPort OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.22 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port identifier for the port which offers the lowest cost path to the root, i.e. that port for which the sum of the values of the designated cost and path cost parameters held for the port is lowest." ::= { nb30Device 22 } nb30DeviceDesigRoot OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.23 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The unique identifier of the bridge recorded as the root." ::= { nb30Device 23 } nb30DeviceMaxAge OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.24 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum age of received protocol information before it is discarded." ::= { nb30Device 24 } nb30DeviceHoldTime OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.25 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The minimum time period elapsing between the transmission of configuration BPDU's through a given bridge port." ::= { nb30Device 25 } nb30DeviceFwdDly OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.26 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The time spent in the listening state while moving from the blocking state to the learning state, or the time spent in the learning state while moving from the listening state to the forwarding state." ::= { nb30Device 26 } nb30DeviceHelloTime OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.27 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The time interval between the transmission of Configuration BPDU's by a bridge which is attempting to become the root or is the root." ::= { nb30Device 27 } nb30DeviceBdgFwdDly OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.28 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The value of the forward delay parameter when the bridge is the root or is attempting to become the root. A time of 4 to 30 seconds is allowed. The default is 15 seconds." ::= { nb30Device 28 } nb30DeviceBdgMaxAge OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.29 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The value of the Max Age parameter when the bridge is the root or is attempting to become the root. A time of 6 to 40 seconds is allowed. The default is 20 seconds." ::= { nb30Device 29 } nb30DeviceBdgHello OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.30 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The value of the Hello Time parameter when the bridge is the root or is attempting to become the root. A time of 1 to 10 seconds is allowed. The default is 2 seconds." ::= { nb30Device 30 } nb30DeviceBdgPriority OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.31 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Used in the spanning tree for priority comparisons. Allowed range is 0 through FFFF. The default is 8000." ::= { nb30Device 31 } nb30DeviceResetCounts OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.32 SYNTAX INTEGER { resetCounts(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Reset all counters to zero." ::= { nb30Device 32 } nb30DeviceUptime OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.33 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The time, in seconds, that has elapsed since the bridge was last reset or initialized." ::= { nb30Device 33 } nb30DeviceRootSwitch OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.34 SYNTAX INTEGER { noRoot(1), root(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of the Root switch on the front panel of the NB30." ::= { nb30Device 34 } nb30DeviceFwdBroadcast OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.35 SYNTAX INTEGER { forwardBroadcast(1), filterBroadcast(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of the Forward Broadcast switch on the front panel of the NB30." ::= { nb30Device 35 } nb30DeviceConfigSw1 OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.36 SYNTAX INTEGER { switchOff(1), switchOn(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of Config switch 1 on the back panel of the NB30." ::= { nb30Device 36 } nb30DeviceConfigSw2 OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.37 SYNTAX INTEGER { switchOff(1), switchOn(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of Config switch 2 on the back panel of the NB30." ::= { nb30Device 37 } nb30DeviceConfigSw3 OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.38 SYNTAX INTEGER { switchOff(1), switchOn(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of Config switch 3 on the back panel of the NB30." ::= { nb30Device 38 } nb30DeviceConfigSw4 OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.39 SYNTAX INTEGER { switchOff(1), switchOn(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of Config switch 4 on the back panel of the NB30." ::= { nb30Device 39 } nb30DevicePortActive OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.40 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The Port number which is acting as the online Ethernet Port on the NB30." ::= { nb30Device 40 } nb30DeviceDefPort OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.41 SYNTAX INTEGER { ethernetPort1(1), ethernetPort2(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The Port number which is Default Ethernet Port on the NB30 at power up." ::= { nb30Device 41 } nb30DeviceRedEnable OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.1.42 SYNTAX INTEGER { disableRedundancy(1), enableRedundancy(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The state of the Redundancy Enable Flag." ::= { nb30Device 42 } -- This section defines the objects specific to the DSX-1 Remote interface. -- -- DSX-1 Remote Interface Objects nb30DsxLoopUp OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.2.1 SYNTAX INTEGER { loopUp(1) } ACCESS read-write STATUS mandatory DESCRIPTION "The loop up command for the DSX-1 Remote Interface." ::= { nb30Dsx 1 } nb30DsxLoopDn OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.2.2 SYNTAX INTEGER { loopDown(1) } ACCESS read-write STATUS mandatory DESCRIPTION "The loop down command for the DSX-1 Remote Interface." ::= { nb30Dsx 2 } nb30DsxLoopSt OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.2.3 SYNTAX INTEGER { notInLoopback(1), loopbackInProgress(2), networkLoopback(3), loopbackPassed(4), loopbackFailed(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The loop status for the DSX-1 Remote Interface." ::= { nb30Dsx 3 } nb30DsxLoopPattern OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.2.4 SYNTAX INTEGER { alternate1sAnd0s(1), all1s(2), all0s(3), incrementingData(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The loop test pattern for the DSX-1 Remote Interface." ::= { nb30Dsx 4 } -- DSX-1 Channel Object Definitions -- -- This section defines the objects under the DSX-1 Channel node. -- -- Instance Identifiers for DSX-1 Channel Objects -- -- The Instance Identifier for nb30DsxChannel objects is the number of -- channels on the DSX-1 interface. Valid instance identifiers for the -- remote channels are 1 - 24. -- -- DSX-1 Channel Objects nb30DsxChannelTable OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.3.1 SYNTAX SEQUENCE OF Nb30DsxEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "NB30 DSX-1 Remote Port Channelization Table" ::= { nb30DsxChannel 1 } nb30DsxEntry OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.3.1.1 SYNTAX Nb30DsxEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { nb30DsxChannelId } ::= { nb30DsxChannelTable 1 } Nb30DsxEntry ::= SEQUENCE { nb30DsxChannelControl INTEGER, nb30DsxChannelId INTEGER } nb30DsxChannelControl OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.3.1.1.1 SYNTAX INTEGER { disableChannel(1), enableChannel(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Disable the DSX-1 Channel." ::= { nb30DsxEntry 1 } nb30DsxChannelId OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The channel number for this entry." ::= { nb30DsxEntry 2 } -- Port Object Definitions -- -- This section defines the objects under the Port node. -- -- Instance Identifiers for Port Objects -- -- The Instance Identifier for nb30Port objects is the number of the -- port on the bridge. Valid instance identifiers for the ports on -- the NB30 are 1 and 2. -- -- Port Objects nb30PortTable OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1 SYNTAX SEQUENCE OF Nb30PortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Bridge Port information table" ::= { nb30Port 1 } nb30PortEntry OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1 SYNTAX Nb30PortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { nb30PortId } ::= { nb30PortTable 1 } Nb30PortEntry ::= SEQUENCE { nb30PortAddress OCTET STRING, nb30PortName OCTET STRING, nb30PortType OCTET STRING, nb30PortStatus OCTET STRING, nb30PortNetName OCTET STRING, nb30PortFrRxs Counter, nb30PortDisInbounds Counter, nb30PortFwdOutbs Counter, nb30PortDisLOBs Counter, nb30PortDisTDEs Counter, nb30PortCollisions Counter, nb30PortTxAborts Counter, nb30PortOowCollisions Counter, nb30PortCRCErrs Counter, nb30PortFrAlignErrs Counter, nb30PortPriority INTEGER, nb30PortState OCTET STRING, nb30PortPathCost INTEGER, nb30PortDesigCost INTEGER, nb30PortDesigBrdg OCTET STRING, nb30PortDesigPort INTEGER, nb30PortTopChgAck INTEGER , nb30PortDesigRoot OCTET STRING, nb30PortOversizePkts Counter, nb30PortFrFiltereds Counter, nb30PortPollAddress OCTET STRING, nb30PortPollInterval INTEGER, nb30PortMaxRetry INTEGER, nb30PortId INTEGER } nb30PortAddress OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.1 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The Ethernet address of the port. Instance of 1 represents the local Ethernet address, instance of 2 represents the remote Ethernet address." ::= { nb30PortEntry 1 } nb30PortName OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.2 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The user-defined name (up to 32 characters long) assigned to the port. The default Enet port 1 name is ETHERNET PORT 1 and the default Enet Port 2 name is ETHERNET PORT 2." ::= { nb30PortEntry 2 } nb30PortType OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.3 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The IEEE specification the port meets, e.g. 802.3." ::= { nb30PortEntry 3 } nb30PortStatus OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.4 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The status in which the port is operating. The status messages for Ports 1 and 2 are: OFF - The port is off, due to a failed network interface chip associated with that port. OK/SQE ON - The port is communicating with the network and the transceiver making the connection to the network has SQE enabled. OK/SQE OFF - The port is communicating with the network and the transceiver making the connection to the network has SQE disabled. CARRIER LOST - Communication with the network has not been established or has been lost." ::= { nb30PortEntry 4 } nb30PortNetName OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.5 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The user-defined name (up to 32 characters long) assigned to a network segment connected to the port. The default network name for Port 1 is LAN_1 and the default network name for Port 2 is LAN_2." ::= { nb30PortEntry 5 } nb30PortFrRxs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.6 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received at the specified port." ::= { nb30PortEntry 6 } nb30PortDisInbounds OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.7 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of valid frames that were received at the port but then discarded by the bridge in the forwarding process." ::= { nb30PortEntry 7 } nb30PortFwdOutbs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.8 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames forwarded successfully to the appropriate port." ::= { nb30PortEntry 8 } nb30PortDisLOBs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.9 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data." ::= { nb30PortEntry 9 } nb30PortDisTDEs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.10 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was possible." ::= { nb30PortEntry 10 } nb30PortCollisions OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.11 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of collisions that have occurred on the network at the specified port." ::= { nb30PortEntry 11 } nb30PortTxAborts OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.12 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of transmissions that have been aborted due to excessive collisions (over 16 attempts to transmit the same packet)." ::= { nb30PortEntry 12 } nb30PortOowCollisions OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.13 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of collisions out of the standard collision window (51.2 uS). This indicates a network problem." ::= { nb30PortEntry 13 } nb30PortCRCErrs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.14 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets detected with Cyclical Redundancy Check failures." ::= { nb30PortEntry 14 } nb30PortFrAlignErrs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.15 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of errors due to misaligned packets." ::= { nb30PortEntry 15 } nb30PortPriority OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.16 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The part of the port identifier which is used with the spanning tree algorithm when determining which port in a LAN segment has priority. The default is 80. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port." ::= { nb30PortEntry 16 } nb30PortState OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.17 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the port, DISABLED, LISTENING, LEARNING, FORWARDING or BLOCKING. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port." ::= { nb30PortEntry 17 } nb30PortPathCost OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.18 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The contributory cost of the applicable port to the overall cost of the path when the specified port is the root port. Allowable range is 1 to 65535. The default is 1000. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port." ::= { nb30PortEntry 18 } nb30PortDesigCost OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.19 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The cost of the path of this port to the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port." ::= { nb30PortEntry 19 } nb30PortDesigBrdg OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.20 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The network address of the bridge that is assumed to be the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port." ::= { nb30PortEntry 20 } nb30PortDesigPort OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.21 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port identifier of the bridge port believed to be the designated port for the LAN associated with the port. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port." ::= { nb30PortEntry 21 } nb30PortTopChgAck OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.22 SYNTAX INTEGER { noTopologyChangeIsOccurring(1), topologyChangeIsOccurring(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The value of the topology change acknowledgement flag in the next configuration BPDU to be transmitted on the associated port. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port." ::= { nb30PortEntry 22 } nb30PortDesigRoot OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.23 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The unique bridge identifier of the bridge that is assumed to be the root bridge on the network. Applies to the LOCAL and REMOTE Ethernet ports where instance 1 always refers to the local ethernet port and instance 2 always refers to the remote ethernet port." ::= { nb30PortEntry 23 } nb30PortOversizePkts OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.24 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets received at the indicated NB30 Port that were greater than the IEEE 802.3 maximum Ethernet frame size of 1518 bytes." ::= { nb30PortEntry 24 } nb30PortFrFiltereds OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.25 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received at the indicated port that were filtered by the bridge." ::= { nb30PortEntry 25 } nb30PortPollAddress OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.26 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The Poll Address that will be used by the Redundant Port Algorithm on the NB30." ::= { nb30PortEntry 26 } nb30PortPollInterval OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.27 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The Poll Interval used by the Redundant Port Algorithm on the NB30. Valid range is 1 - 30 seconds." ::= { nb30PortEntry 27 } nb30PortMaxRetry OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.4.1.1.28 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The Max number of retries for the Redundant Port Algorithm on the NB30. Valid range is 2 - 99 retries" ::= { nb30PortEntry 28 } nb30PortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The port number for this entry." ::= { nb30PortEntry 29 } -- Remote Port Object Definitions -- -- This section defines the objects under the Remote Port node. -- -- Instance Identifiers for Remote Port Objects -- -- There is only one instance of the remote port on the NB30 bridge -- thus the Instance Identifier is 0. -- -- Port Objects nb30RemPortTable OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1 SYNTAX SEQUENCE OF Nb30RemPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Bridge Remote Port information table" ::= { nb30RemPort 1 } nb30RemPortEntry OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1 SYNTAX Nb30RemPortEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { nb30RemPortId } ::= { nb30RemPortTable 1 } Nb30RemPortEntry ::= SEQUENCE { nb30RemPortName OCTET STRING, nb30RemPortType OCTET STRING, nb30RemPortStatus OCTET STRING, nb30RemPortNetName OCTET STRING, nb30RemPortFrRxs Counter, nb30RemPortFwdOutbs Counter, nb30RemPortDisLOBs Counter, nb30RemPortDisTDEs Counter, nb30RemPortCRCErrs Counter, nb30RemPortFrAlErrs Counter, nb30RemPortId INTEGER } nb30RemPortName OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.1 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The user-defined name assigned to the remote port. The default Remote port name is REMOTE PORT." ::= { nb30RemPortEntry 1 } nb30RemPortType OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.2 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The Electrical interface specification the port meets, e.g. DSX-1, V.35." ::= { nb30RemPortEntry 2 } nb30RemPortStatus OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.3 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The status in which the remote port is operating. The status messages for the Remote Port are: NO EXT CLOCK DCE NOT READY / NO DM DCE NOT READY / NO CTS LINK OK / DCE READY NET LOOP / RED ALARM REM LOOP / RED ALARM NORMAL / RED ALARM NET LOOP / YELLOW ALARM REM LOOP / YELLOW ALARM NORMAL / YELLOW ALARM NET LOOP / LINK OK REM LOOP / LINK OK NORMAL / LINK OK NET LOOP / LINK LOST REM LOOP / LINK LOST NORMAL / LINK LOST" ::= { nb30RemPortEntry 3 } nb30RemPortNetName OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.4 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The user-defined name assigned to a wide area segment connected to the remote port. The default network name for Remote Port is REMOTE LINK." ::= { nb30RemPortEntry 4 } nb30RemPortFrRxs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.5 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames received at the remote port." ::= { nb30RemPortEntry 5} nb30RemPortFwdOutbs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.6 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames forwarded successfully to the remote port." ::= { nb30RemPortEntry 6 } nb30RemPortDisLOBs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.7 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets that were discarded by the bridge because of a lack of buffer space to maintain the data." ::= { nb30RemPortEntry 7 } nb30RemPortDisTDEs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.8 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of frames that were intended for forwarding but were discarded when the maximum time period set for transmission was exceeded before forwarding was possible." ::= { nb30RemPortEntry 8 } nb30RemPortCRCErrs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.9 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets detected with Cyclical Redundancy Check failures." ::= { nb30RemPortEntry 9 } nb30RemPortFrAlErrs OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.5.1.1.10 SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of errors due to misaligned packets." ::= { nb30RemPortEntry 10 } nb30RemPortId OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The remote port ID, there is only a single port which is identified as 0." ::= { nb30RemPortEntry 11 } -- Acquired Database Statistical Object Definitions -- -- This section defines the objects under the Acquired Database -- Statistics node. -- -- Instance Identifiers for Acquired Database Statistical Objects -- -- There is only one instance of an Acquired Database Statistical object, -- thus the Instance Identifier is 0. -- -- Acquired Database Statistical Objects nb30AcqTotalEntries OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.1 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total number of entries in the acquired database." ::= { nb30AcqDB 1 } nb30AcqMaxEntries OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.2 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of entries allowed in the acquired database 8191 entries." ::= { nb30AcqDB 2 } nb30AcqStaticEntries OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.3 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of addresses added to the Acquired database by the user or network manager." ::= { nb30AcqDB 3 } nb30AcqDynamicEntries OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.4 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of entries that have been accumulated in the Acquired database through the bridge's learning process." ::= { nb30AcqDB 4 } nb30AcqDynAgeTime OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.5 SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The length of time allowed for a dynamic entry in the acquired database to be inactive before it is dropped from the database. A time from 10 - 1,000,000 seconds is allowed. The default is 300 seconds." ::= { nb30AcqDB 5 } nb30AcqEraseDatabase OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.6 SYNTAX INTEGER { eraseAcquiredDatabase(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Set to one to erase all entries in the acquired database." ::= { nb30AcqDB 6 } -- Aquired database tables -- nb30AcqDBTable OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.7 SYNTAX SEQUENCE OF Nb30AcqDBEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Aquired database entrys table" ::= { nb30AcqDB 7 } nb30AcqDBEntry OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.7.1 SYNTAX Nb30AcqDBEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { nb30AcqMacAddress } ::= { nb30AcqDBTable 1 } Nb30AcqDBEntry ::= SEQUENCE { nb30AcqCreateFilter INTEGER, nb30AcqCreateForward INTEGER, nb30AcqDeleteFilter INTEGER, nb30AcqFilterType OCTET STRING, nb30AcqFilterAction INTEGER, nb30AcqSourceAddress OCTET STRING, nb30AcqMacAddress OCTET STRING } -- Acquired Database Option Object Definitions -- -- This section defines the objects under the Acquired Database -- Option node. -- -- Instance Identifiers for Acquired Database Option Objects -- -- The instance identifier for the acquired database option objects is -- the 6-byte Ethernet address of the device to be added, deleted or -- displayed to/from the acquired database. -- -- Acquired Database Option Objects nb30AcqCreateFilter OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.7.1.1 SYNTAX INTEGER { createAcquiredFilter(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Add an entry to the acquired database to filter packets entering port 1 if those packets are destined for the specified address." ::= { nb30AcqDBEntry 1 } nb30AcqCreateForward OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.7.1.2 SYNTAX INTEGER { createAcquiredForward(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Add an entry to the acquired database to forward packets entering port 1 to the remote port if those packets are destined for the specified address." ::= { nb30AcqDBEntry 2 } nb30AcqDeleteFilter OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.7.1.3 SYNTAX INTEGER { deleteAcquiredEntry(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Delete an entry from the acquired database." ::= { nb30AcqDBEntry 3 } nb30AcqFilterType OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.7.1.4 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Display the entry type, STATIC or DYNAMIC." ::= { nb30AcqDBEntry 4 } nb30AcqFilterAction OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.7.1.5 SYNTAX INTEGER { filter(1), relay(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The action to be taken for packets entering port 1." ::= { nb30AcqDBEntry 5 } nb30AcqSourceAddress OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.1.7.1.6 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The source address of this acquired database entry, i.e. the instance." ::= { nb30AcqDBEntry 6 } nb30AcqMacAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "The MAC address for the specific entry." ::= { nb30AcqDBEntry 7 } -- Permanent Database Statistical Object Definitions -- -- This section defines the objects under the Permanent Database -- Statistics node. -- -- Instance Identifiers for Permanent Database Statistical Objects -- -- There is only one instance of an Permanent Database Statistical -- object, thus the Instance Identifier is 0. -- -- Permanent Database Statistical Objects nb30PermMaxEntries OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.1 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of entries allowed in the permanent database 2047 entries." ::= { nb30PermDB 1 } nb30PermCurrentEntries OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.2 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of entries currently recorded in the bridge's permanent database." ::= { nb30PermDB 2 } nb30PermEraseDatabase OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.3 SYNTAX INTEGER { erasePermanentDatabase(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Erase all entries in the permanent database." ::= { nb30PermDB 3 } -- Permanent Database Option Object Definitions -- -- This section defines the objects under the Permanent Database -- Option node. -- -- Instance Identifiers for Permanent Database Option Objects -- -- The instance identifier for the permanent database option objects is -- the 6-byte Ethernet address of the device to be added, deleted or -- displayed to/from the permanent database. -- -- Permanent Database Option Objects nb30PermDBTable OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.4 SYNTAX SEQUENCE OF Nb30PermDBEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Aquired database entrys table" ::= { nb30PermDB 4 } nb30PermDBEntry OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.4.1 SYNTAX Nb30PermDBEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { nb30PermDBMacAddress } ::= { nb30PermDBTable 1 } Nb30PermDBEntry ::= SEQUENCE { nb30PermCreateFilter INTEGER, nb30PermCreateForward INTEGER, nb30PermDeleteEntry INTEGER, nb30PermFilterType OCTET STRING, nb30PermFilterAction INTEGER, nb30PermSourceAddress OCTET STRING, nb30PermDBMacAddress OCTET STRING } nb30PermCreateFilter OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.4.1.1 SYNTAX INTEGER { createPermanentFilter(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Add an entry to the permanent database to filter packets entering port 1 if those packets are destined for the specified address." ::= { nb30PermDBEntry 1 } nb30PermCreateForward OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.4.1.2 SYNTAX INTEGER { createPermanentForward(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Add an entry to the permanent database to forward packets entering port 1 to the remote port if those packets are destined for the specified address." ::= { nb30PermDBEntry 2 } nb30PermDeleteEntry OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.4.1.3 SYNTAX INTEGER { deletePermanentEntry(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Delete an entry from the permanent database." ::= { nb30PermDBEntry 3 } nb30PermFilterType OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.4.1.4 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Display the entry type, STATIC ." ::= { nb30PermDBEntry 4 } nb30PermFilterAction OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.4.1.5 SYNTAX INTEGER { filter(1), relay(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The action taken on packets entering port 1." ::= { nb30PermDBEntry 5 } nb30PermSourceAddress OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.2.4.1.6 SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The source address in this permanent database entry, i.e. the instance." ::= { nb30PermDBEntry 6 } nb30PermDBMacAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "The specific MAC address for this entry." ::= { nb30PermDBEntry 7 } -- Special Database Statistical Object Definitions -- -- This section defines the objects under the Special Database -- Statistical node. -- -- Instance Identifiers for Special Database Statistical Objects -- -- There is only one instance of a Special Database Statistical object, -- thus the Instance Identifier is 0. -- -- Special Database Statistical Objects nb30SpecNumEntries OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.1 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of filters in the special database." ::= { nb30SpecDB 1 } nb30SpecMaxEntries OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.2 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of filters the special database can contain." ::= { nb30SpecDB 2 } nb30SpecNextFilterNum OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.3 SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of the next available filter that can be added to the special database. This OID will return a 255 if the database is full" ::= { nb30SpecDB 3 } -- Special Database Filter Object Definitions -- -- This section defines the objects under the Special Database -- Filter node. -- -- Instance Identifiers for Special Database Filter Objects -- -- The instance identifier of the special database filter objects -- is the filter number, values from 1 through 10 are allowed. -- -- Special Database Filter Objects nb30SpecDBTable OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4 SYNTAX SEQUENCE OF Nb30SpecDBEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" ::= { nb30SpecDB 4 } nb30SpecDBEntry OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4.1 SYNTAX Nb30SpecDBEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { nb30SpecDbFilterNumber } ::= { nb30SpecDBTable 1 } Nb30SpecDBEntry ::= SEQUENCE { nb30SpecEnable INTEGER, nb30SpecPort1 INTEGER, nb30SpecDestAddress OCTET STRING, nb30SpecSrcAddress OCTET STRING, nb30SpecType OCTET STRING, nb30SpecDataField OCTET STRING, nb30SpecDeleteFilter INTEGER, nb30SpecDbFilterNumber INTEGER } nb30SpecEnable OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4.1.1 SYNTAX INTEGER { disableFilter(1), enableFilter(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable or disable the filter." ::= { nb30SpecDBEntry 1 } nb30SpecPort1 OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4.1.2 SYNTAX INTEGER { filter(1), relay(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set port 1 to filter or forward packets." ::= { nb30SpecDBEntry 2 } nb30SpecDestAddress OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4.1.3 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "Set the special database to filter packets with a specific destination address." ::= { nb30SpecDBEntry 3 } nb30SpecSrcAddress OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4.1.4 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "Set the special database to filter packets with a specific source address." ::= { nb30SpecDBEntry 4 } nb30SpecType OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4.1.5 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "Set the special database to filter packets with a specific type field." ::= { nb30SpecDBEntry 5 } nb30SpecDataField OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4.1.6 SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "Set the special database to filter packets based on the first sixteen bytes of data in the packet." ::= { nb30SpecDBEntry 6 } nb30SpecDeleteFilter OBJECT-TYPE --OID 1.3.6.1.4.1.52.1.6.12.6.3.4.1.7 SYNTAX INTEGER { deleteFilter(1) } ACCESS read-write STATUS mandatory DESCRIPTION "Delete a filter from the special database." ::= { nb30SpecDBEntry 7 } nb30SpecDbFilterNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The specific special data base filter number." ::= { nb30SpecDBEntry 8 } END