All MIBs › MRV-IN-REACH-SYSTEM-MIB
Category: Network Management
Description:
Monitors MRV In-Reach system resources, uptime, and software configuration.
Imported Objects
From MRV-IN-REACH-PRODUCT-DIVISION-MIB
| AddressType | |
| ChassisType | |
| DateTime | |
| HardwareType | |
| TypedAddress | |
| mrvInReachProductDivision | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| TimeTicks |
From RFC1213-MIB
| DisplayString | |
| sysLocation |
What Is MRV-IN-REACH-SYSTEM-MIB?
MRV-IN-REACH-SYSTEM-MIB is a vendor-specific enterprise MIB from MRV Communications for its In-Reach family of secure console/terminal access servers used for out-of-band management of network equipment. It exposes system-level status information such as device identification, uptime, and software/firmware version, along with general system resource and configuration data. The MIB is squarely aimed at monitoring the hardware and software health of the In-Reach unit itself — administrators use it to confirm the box is up, check how long it has been running, and verify which firmware release is loaded. Like most enterprise system MIBs it commonly builds on the standard SNMPv2-SMI and MIB-II (system group) conventions for its base structure. It is typically deployed in data centers and remote sites where In-Reach console servers provide lights-out access to routers, switches, and servers, with an NMS polling this MIB alongside traps to confirm the management-access path itself is healthy. Engineers can download the MRV-IN-REACH-SYSTEM-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in MRV-IN-REACH-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
What Can Be Monitored
- system uptime
- firmware/software version
- system identification
- general device status
Supported Devices
- MRV In-Reach terminal/console server
- MRV network access device
Monitoring Examples
No object/table names were provided for this module in the available source, so specific OIDs cannot be cited; in practice an admin would poll the device's system uptime and software version objects to confirm the In-Reach unit has not silently rebooted and is running the expected firmware. A sudden uptime reset or unexpected version string would indicate the console server itself needs attention, which is critical since it's often the last-resort path for accessing other equipment.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF resourceFailure | 1.3.6.1.4.1.33.0.9 | Indication that a system resource lack occurred of the type resType. | ||
| NTF sysLoginAuthenticationFailure | 1.3.6.1.4.1.33.0.28 | Indicates when and where a user attempted and failed to access the system. | ||
| xSystem | 1.3.6.1.4.1.33.1 | |||
| NTF resourceLack | 1.3.6.1.4.1.33.1.0.1 | Indication that the system incremented the corresponding value of resLacks. | ||
| STR sysIdent | 1.3.6.1.4.1.33.1.1 | DisplayString | read-write | An identification string for local and remote displays. Corresponds directly to SERVER IDENTIFICATION and the value labeled 'Identification:' on the SERVER CHARACTERISTICS display. |
| INT sysDefineMode | 1.3.6.1.4.1.33.1.2 | INTEGER | read-write | The system's operation with regard to DEFINE commands. 'permOnly' indicates that DEFINE commands modify only the permanent data base. 'operAndPerm' indicates that DEFINE commands modify both operational and permanent data bases, unless specifically documented to the contrary. Corresponds to SERVER CHANGE and the presence of the label CHANGE in the SERVER CHARACTERISTICS display. |
| DAT sysDateTime | 1.3.6.1.4.1.33.1.3 | DateTime | read-write | The system's current local date and time. Corresponds directly to SERVER DATE and SERVER TIME and the value in various displays. |
| OCT sysTimeZone | 1.3.6.1.4.1.33.1.4 | OCTET STRING | read-write | The adjustment to apply to a universal (Greenwich) time received when down-line loaded, comprising two octets. The first octet is the number of hours west of universal, the second is the number of minutes. Corresponds directly to SERVER TIMEZONE and the value labeled 'Timezone:' in the SERVER CHARACTERISTICS display. |
| STR sysLoadSoftware | 1.3.6.1.4.1.33.1.5 | DisplayString | read-write | The software file name to request for down-line load of the server. Corresponds directly to SERVER SOFTWARE, and the value labeled 'Software:' in the SERVER CHARACTERISTICS display. |
| INT sysDump | 1.3.6.1.4.1.33.1.6 | INTEGER | read-write | Control for dumping the system's memory when the system crashes. Corresponds directly to SERVER DUMP and the presence of 'Dump' under the label 'Enabled Characteristics' in the SERVER CHARACTERISTICS display. |
| OCT sysMaintenancePassword | 1.3.6.1.4.1.33.1.7 | OCTET STRING | read-write | The password a management system must supply to force the system to reboot or use the system's remote console via the Maintenance Operation Protocol (MOP). Corresponds directly to SERVER MAINTENANCE PASSWORD. When setting this value, the management system must supply eight octets, filling with zeros from the first octet. That is, the value '1ab42' would be expressed as '0.0.0.0.0.1.ab.42'. Setting the value to zero disables the password check. When returning this value, the agent always returns a zero length OCTET STRING. |
| STR sysLocalName | 1.3.6.1.4.1.33.1.8 | DisplayString | read-write | The system's local name. Corresponds directly to SERVER NAME and the value labeled 'Name:' in the SERVER CHARACTERISTICS display. |
| INT sysSoftwareVersionType | 1.3.6.1.4.1.33.1.9 | INTEGER | read-only | The software version variant running in the system. Corresponds to the letter in the software version in the SERVER CHARACTERISTICS display. alpha 'A': alpha test beta 'B': beta test production null: normal, production software special 'S': special, custom software |
| OCT sysSoftwareVersion | 1.3.6.1.4.1.33.1.10 | OCTET STRING | read-only | The software version running in the system. In order, the octets contain major version, minor version, ECO, and pre-release number. Corresponds to the numbers in the software version in the SERVER CHARACTERISTICS display. For example, the version display for sysSoftwareVersionType 'production' and sysSoftwareVersion '2.2.0.0' is 'V2.2'. The version display for sysSoftwareVersionType 'beta' and sysSoftwareVersion '3.1.0.4' is 'V3.1B4'. |
| INT sysRomVersion | 1.3.6.1.4.1.33.1.11 | INTEGER | read-only | The firmware version of the bootstrap ROM installed in the system. Corresponds directly to the value labeled 'Rom' in the SERVER CHARACTERISTICS display. |
| HAR sysHardwareType | 1.3.6.1.4.1.33.1.12 | HardwareType | read-only | The type of hardware on which the system is running. Corresponds directly to the value labeled 'Hardware Type:' in the UNIT display. |
| INT sysHardwareVersion | 1.3.6.1.4.1.33.1.13 | INTEGER | read-only | This version of hardware on which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| CHA sysChassisType | 1.3.6.1.4.1.33.1.14 | ChassisType | read-only | The type of chassis in which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| INT sysChassisVersion | 1.3.6.1.4.1.33.1.15 | INTEGER | read-only | This version of chassis in which the system is running. Corresponds directly to part of the value labeled 'HW' in the SERVER CHARACTERISTICS display. |
| INT sysCrash | 1.3.6.1.4.1.33.1.16 | INTEGER | read-write | Control to cause this system to crash. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes an immediate crash. Corresponds to the CRASH command. |
| INT sysInitialize | 1.3.6.1.4.1.33.1.17 | INTEGER | read-write | Control to cause this system to reset its software to initial load values, typically by reloading. When executing an initialize command, the system observes the value of sysInitializeDelay as supplied anywhere in the same set request with sysInitialize. If this value is not included in the set request, the system uses its default value. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'conditionalExecute' causes initialization if the overall system state is acceptible (such as not needing to store permanent parameters). Setting it to 'unconditionalExecute' causes initialization regardless of the overall system state. Setting it to 'cancel' aborts an initialization that has not yet started. According to standard SNMP operation, if the system is not in a proper state to accept a given set request for this value, it returns the standard SNMP error 'badValue'. Corresponds to the INITIALIZE command. |
| INT sysInitializeDelay | 1.3.6.1.4.1.33.1.18 | INTEGER | read-write | The number of minutes to delay before beginning the system initialization process as executed with sysInitialize. This value cannot be set outside a set-request that contains the value 'execute' for sysInitialize. If not included in such a set, the default value is 1. Corresponds to the INITIALIZE command's DELAY parameter and to the value labeled 'Minutes to shutdown:' in the SYSTEM STATUS display. |
| INT sysZeroAll | 1.3.6.1.4.1.33.1.19 | INTEGER | read-write | Control to zero all counters. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes all the system's counters to be zeroed. Corresponds to the ZERO ALL command. |
| INT sysZeroBase | 1.3.6.1.4.1.33.1.20 | INTEGER | read-write | Control to zero all base counters. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes all the system's base counters to be zeroed. Examples of counters that are zeroed are the SNMP counters or the counters from the SYSTEM COUNTERS display. Examples of counters that are not zeroed are Ethernet interface counters or port counters. Corresponds to the ZERO SYSTEM command. |
| TIK sysZeroBaseTime | 1.3.6.1.4.1.33.1.21 | TimeTicks | read-only | The number hundredths of a second since the most recent zeroing of the base counters, such as through execution of sysZeroAll or sysZeroBase. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the SERVER COUNTERS display. |
| STR sysLoaderName | 1.3.6.1.4.1.33.1.22 | DisplayString | read-only | The name of the system that provided this system's running software. Corresponds directly to the value labeled 'Primary Host:' in the SERVER STATUS display. |
| ADR sysLoaderAddressType | 1.3.6.1.4.1.33.1.23 | AddressType | read-only | The type of network address contained in sysLoaderAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'local' means there is no address and this system's software was loaded from local storage. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the value labeled 'Load Address:' in the SERVER STATUS display. |
| OCT sysLoaderAddress | 1.3.6.1.4.1.33.1.24 | OCTET STRING | read-only | The network address of the system that provided this system's running software. Corresponds directly to the value labeled 'Load Address:' in the SERVER STATUS display. |
| ADR sysDumperAddressType | 1.3.6.1.4.1.33.1.25 | AddressType | read-only | The type of network address contained in sysDumperAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'local' means there is no address and this system's was dumped to local storage. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. Corresponds indirectly to the value labeled 'Dump Address:' in the SERVER STATUS display. |
| OCT sysDumperAddress | 1.3.6.1.4.1.33.1.26 | OCTET STRING | read-only | The network address of the system that most recently accepted a crash dump from this system. Corresponds directly to the value labeled 'Dump Address:' in the SERVER STATUS display. |
| CTR sysResourceLacks | 1.3.6.1.4.1.33.1.27 | Counter | read-only | The number of times a local resource allocation failed, for example due to lack of dynamic memory. Corresponds directly to the value labeled 'Resource Errors:' in the SERVER STATUS display. |
| INT sysChassisState | 1.3.6.1.4.1.33.1.28 | INTEGER | read-only | For chassis-based systems, the state of the overall chassis. 'notApplicable' indicates the system is not chassis based. 'noFault' indicates no current chassis problem. 'fault' indicates a current chassis problem such as a card or power supply failure. Corresponds directly to the value labeled 'Crate Current State: in the SERVER ALTERNATE STATUS display. |
| CTR sysChassisFaultTransitions | 1.3.6.1.4.1.33.1.29 | Counter | read-only | The number of times this system has seen sysChassisState switch from 'noFault' to 'fault' or from 'fault' to 'noFault'. Corresponds directly to the value labeled 'Crate Transition Count: in the SERVER ALTERNATE STATUS display. |
| INT sysResourceNumber | 1.3.6.1.4.1.33.1.30 | INTEGER | read-only | The number of resource entries in the Resource table. |
| INT sysFeatureNumber | 1.3.6.1.4.1.33.1.31 | INTEGER | read-only | The number of feature entries in the Feature table. |
| resTable | 1.3.6.1.4.1.33.1.32 | not-accessible | A list of resource entries. The number of entries is given by the value of sysResourceNumber. | |
| resEntry | 1.3.6.1.4.1.33.1.32.1 | not-accessible | Status values for a system resource. | |
| INT resType | 1.3.6.1.4.1.33.1.32.1.1 | INTEGER | read-only | Identification of a resource type. Typically corresponds directly to a label such as 'Processes:' in the SERVER ALTERNATE STATUS display. |
| GAU resCurrent | 1.3.6.1.4.1.33.1.32.1.2 | Gauge | read-only | The number of resources currently in use on the system. Typically corresponds directly to a value labeled 'Cur' in the SERVER ALTERNATE STATUS display. |
| GAU resWorst | 1.3.6.1.4.1.33.1.32.1.3 | Gauge | read-only | The highest or lowest value of resCurrent since system initialization. Typically corresponds directly to a value labeled 'High' or 'Low' in the SERVER ALTERNATE STATUS display. |
| INT resAdminMaximum | 1.3.6.1.4.1.33.1.32.1.4 | INTEGER | read-write | The desired maximum possible number of resources in the system. In many cases, ACCESS to this object for a particular resType is read-only. Typically corresponds directly to a value labeled 'Max' in the SERVER ALTERNATE STATUS display for desired, administrative values. When the desired change takes effect is implementation specific, ranging from immediately to the next system initialization. |
| CTR resLacks | 1.3.6.1.4.1.33.1.32.1.5 | Counter | read-only | The number of times since system initialization that the system could not obtain the resource because none were available. Typically corresponds directly to a value labeled 'Failure' in the SERVER ALTERNATE STATUS display. If such failures do not apply to the particular resource, such as 'cpuPercent', the agent returns zero for this object. |
| DAT resLackTime | 1.3.6.1.4.1.33.1.32.1.6 | DateTime | read-only | The local system date and time when resLack last increased. Typically corresponds directly to a value labeled 'Last Occurred' in the SERVER ALTERNATE STATUS display. If such failures do not apply to the particular resource, such as 'cpuPercent', the agent returns all zeroes (unknown) for this object. |
| INT resOperMaximum | 1.3.6.1.4.1.33.1.32.1.7 | INTEGER | read-only | The current maximum possible number of resources in the system. Typically corresponds directly to a value labeled 'Max' in the SERVER ALTERNATE STATUS display for current operational values. This value is based on current or previous value of resAdminMaximum. |
| featTable | 1.3.6.1.4.1.33.1.33 | not-accessible | A list of feature entries. The number of entries is given by the value of sysFeatureNumber. | |
| featEntry | 1.3.6.1.4.1.33.1.33.1 | not-accessible | Status values for a system feature. | |
| INT featType | 1.3.6.1.4.1.33.1.33.1.1 | INTEGER | read-only | Identification of a feature type. Corresponds to a SERVER feature keyword. |
| INT featStatus | 1.3.6.1.4.1.33.1.33.1.2 | INTEGER | read-write | The status of the feature as of the next system initialization. Corresponds to the presence of the feature's lable following the label 'Enabled Feature(s): in the UNIT display. |
| STR featKey | 1.3.6.1.4.1.33.1.33.1.3 | DisplayString | read-write | The key a management system must supply to make a locked feature available. When unlocking a feature and the management system does not supply a value for featStatus, that object's value is implementation dependent. When returning this value, the agent always returns a zero length DisplayString. |
| xBootControl | 1.3.6.1.4.1.33.1.34 | |||
| STR bootControlLoadInternetFile | 1.3.6.1.4.1.33.1.34.1 | DisplayString | read-write | The filename to request when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD FILE and the value labeled 'Internet Load File:' in the SERVER BOOT CHARACTERISTICS display. |
| IP bootControlLoadInternetServer | 1.3.6.1.4.1.33.1.34.2 | IpAddress | read-write | The internet address of the server to use when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD HOST and the value labeled 'Internet Load Host:' in the SERVER BOOT CHARACTERISTICS display. |
| IP bootControlLoadInternetGateway | 1.3.6.1.4.1.33.1.34.3 | IpAddress | read-write | The internet address of the gateway to use when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD GATEWAY and the value labeled 'Internet Load Gateway:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadBootpTftp | 1.3.6.1.4.1.33.1.34.4 | INTEGER | read-write | Control for loading via the combination of BOOTP and TFTP. Corresponds to SERVER LOAD PROTOCOL BOOTPTFTP and the presence of 'BOOTP/TFTP/' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadTftpDirect | 1.3.6.1.4.1.33.1.34.5 | INTEGER | read-write | Control for loading via directed TFTP. Corresponds to SERVER LOAD PROTOCOL TFTPDIRECT and the presence of 'TFTPDIRECT' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadLocal | 1.3.6.1.4.1.33.1.34.6 | INTEGER | read-write | Control for loading from a local medium. Corresponds to SERVER LOAD PROTOCOL LOCAL and the presence of 'LOCAL' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadMop | 1.3.6.1.4.1.33.1.34.7 | INTEGER | read-write | Control for loading via DEC MOP. Corresponds to SERVER LOAD PROTOCOL MOP and the presence of 'MOP' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadProprietary | 1.3.6.1.4.1.33.1.34.8 | INTEGER | read-write | Control for loading via MRV In-Reach-proprietary extended MOP. Corresponds to SERVER LOAD PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlLoadRarpTftp | 1.3.6.1.4.1.33.1.34.9 | INTEGER | read-write | Control for loading via the combination of RARP and TFTP. Corresponds to SERVER LOAD PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpBootpTftp | 1.3.6.1.4.1.33.1.34.10 | INTEGER | read-write | Control for dumping via the combination of BOOTP and TFTP. Corresponds to SERVER DUMP PROTOCOL BOOTPTFTP and the presence of 'BOOTP/TFTP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpLocal | 1.3.6.1.4.1.33.1.34.11 | INTEGER | read-write | Control for dumping to a local medium. Corresponds to SERVER DUMP PROTOCOL LOCAL and the presence of 'Local' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpMop | 1.3.6.1.4.1.33.1.34.12 | INTEGER | read-write | Control for dumping via DEC MOP. Corresponds to SERVER DUMP PROTOCOL MOP and the presence of 'MOP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpProprietary | 1.3.6.1.4.1.33.1.34.13 | INTEGER | read-write | Control for dumping via MRV In-Reach-proprietary extended MOP. Corresponds to SERVER DUMP PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlDumpRarpTftp | 1.3.6.1.4.1.33.1.34.14 | INTEGER | read-write | Control for dumping via the combination of RARP and TFTP. Corresponds to SERVER DUMP PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamBootpTftp | 1.3.6.1.4.1.33.1.34.15 | INTEGER | read-write | Control for loading parameters via the combination of BOOTP and TFTP. Corresponds to SERVER PARAMETER PROTOCOL MOP and the presence of 'BOOTP/TFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamLocal | 1.3.6.1.4.1.33.1.34.16 | INTEGER | read-write | Control for loading parameters from a local medium. Corresponds to SERVER PARAMETER PROTOCOL LOCAL and the presence of 'LOCAL' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamMop | 1.3.6.1.4.1.33.1.34.17 | INTEGER | read-write | Control for loading parameters via DEC MOP. Corresponds to SERVER PARAMETER PROTOCOL MOP and the presence of 'MOP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamProprietary | 1.3.6.1.4.1.33.1.34.18 | INTEGER | read-write | Control for loading parameters via MRV In-Reach-proprietary extended MOP. Corresponds to SERVER PARAMETER PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootControlParamRarpTftp | 1.3.6.1.4.1.33.1.34.19 | INTEGER | read-write | Control for loading parameters via the combination of RARP and TFTP. Corresponds to SERVER PARAMETER PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| GAU sysInstalledMemory | 1.3.6.1.4.1.33.1.35 | Gauge | read-only | The total number of bytes of main memory installed in the system. Corresponds directly to the value labeled 'Installed' on the SERVER ALTERNATE STATUS display. A value of 0 indicates standard memory for the particular hardware. |
| INT sysTemperatureLevel | 1.3.6.1.4.1.33.1.36 | INTEGER | read-only | The temperature level of the system. 'unknown' indicates the system does not support a temperature sensor. 'normal' indicates a normal temperature level. 'high' indicates an excessive temperature level. Corresponds directly to the value labeled 'Temperature Level:' in the SERVER ALTERNATE STATUS display. |
| bootRecordTable | 1.3.6.1.4.1.33.1.37 | not-accessible | A list of boot control records. | |
| bootRecordEntry | 1.3.6.1.4.1.33.1.37.1 | not-accessible | Values for a boot record. | |
| INT bootRecordIndex | 1.3.6.1.4.1.33.1.37.1.1 | INTEGER | read-only | An index value that uniquely identifies a boot control record entry, from 1 to the number of entries for the system. |
| STR bootRecordLoadInternetFile | 1.3.6.1.4.1.33.1.37.1.2 | DisplayString | read-write | The filename to request when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD FILE and the value labeled 'Internet Load File:' in the SERVER BOOT CHARACTERISTICS display. |
| IP bootRecordLoadInternetServer | 1.3.6.1.4.1.33.1.37.1.3 | IpAddress | read-write | The internet address of the server to use when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD HOST and the value labeled 'Internet Load Host:' in the SERVER BOOT CHARACTERISTICS display. |
| IP bootRecordLoadInternetGateway | 1.3.6.1.4.1.33.1.37.1.4 | IpAddress | read-write | The internet address of the gateway to use when loading an image via TFTP. Corresponds directly to SERVER INTERNET LOAD GATEWAY and the value labeled 'Internet Load Gateway:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordLoadBootpTftp | 1.3.6.1.4.1.33.1.37.1.5 | INTEGER | read-write | Control for loading via the combination of BOOTP and TFTP. Corresponds to SERVER LOAD PROTOCOL BOOTPTFTP and the presence of 'BOOTP/TFTP/' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordLoadTftpDirect | 1.3.6.1.4.1.33.1.37.1.6 | INTEGER | read-write | Control for loading via directed TFTP. Corresponds to SERVER LOAD PROTOCOL TFTPDIRECT and the presence of 'TFTPDIRECT' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordLoadLocal | 1.3.6.1.4.1.33.1.37.1.7 | INTEGER | read-write | Control for loading from a local medium. Corresponds to SERVER LOAD PROTOCOL LOCAL and the presence of 'LOCAL' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordLoadMop | 1.3.6.1.4.1.33.1.37.1.8 | INTEGER | read-write | Control for loading via DEC MOP. Corresponds to SERVER LOAD PROTOCOL MOP and the presence of 'MOP' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordLoadProprietary | 1.3.6.1.4.1.33.1.37.1.9 | INTEGER | read-write | Control for loading via MRV In-Reach-proprietary extended MOP. Corresponds to SERVER LOAD PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordLoadRarpTftp | 1.3.6.1.4.1.33.1.37.1.10 | INTEGER | read-write | Control for loading via the combination of RARP and TFTP. Corresponds to SERVER LOAD PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Load Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordDumpBootpTftp | 1.3.6.1.4.1.33.1.37.1.11 | INTEGER | read-write | Control for dumping via the combination of BOOTP and TFTP. Corresponds to SERVER DUMP PROTOCOL BOOTPTFTP and the presence of 'BOOTP/TFTP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordDumpLocal | 1.3.6.1.4.1.33.1.37.1.12 | INTEGER | read-write | Control for dumping to a local medium. Corresponds to SERVER DUMP PROTOCOL LOCAL and the presence of 'Local' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordDumpMop | 1.3.6.1.4.1.33.1.37.1.13 | INTEGER | read-write | Control for dumping via DEC MOP. Corresponds to SERVER DUMP PROTOCOL MOP and the presence of 'MOP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordDumpProprietary | 1.3.6.1.4.1.33.1.37.1.14 | INTEGER | read-write | Control for dumping via MRV In-Reach-proprietary extended MOP. Corresponds to SERVER DUMP PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordDumpRarpTftp | 1.3.6.1.4.1.33.1.37.1.15 | INTEGER | read-write | Control for dumping via the combination of RARP and TFTP. Corresponds to SERVER DUMP PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Dump Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordParamBootpTftp | 1.3.6.1.4.1.33.1.37.1.16 | INTEGER | read-write | Control for loading parameters via the combination of BOOTP and TFTP. Corresponds to SERVER PARAMETER PROTOCOL MOP and the presence of 'BOOTP/TFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordParamLocal | 1.3.6.1.4.1.33.1.37.1.17 | INTEGER | read-write | Control for loading parameters from a local medium. Corresponds to SERVER PARAMETER PROTOCOL LOCAL and the presence of 'LOCAL' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordParamMop | 1.3.6.1.4.1.33.1.37.1.18 | INTEGER | read-write | Control for loading parameters via DEC MOP. Corresponds to SERVER PARAMETER PROTOCOL MOP and the presence of 'MOP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordParamProprietary | 1.3.6.1.4.1.33.1.37.1.19 | INTEGER | read-write | Control for loading parameters via MRV In-Reach proprietary extended MOP. Corresponds to SERVER PARAMETER PROTOCOL PROPRIETARY and the presence of 'Proprietary' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordParamRarpTftp | 1.3.6.1.4.1.33.1.37.1.20 | INTEGER | read-write | Control for loading parameters via the combination of RARP and TFTP. Corresponds to SERVER PARAMETER PROTOCOL RARPTFTP and the presence of 'RARP/TFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| INT bootRecordStatus | 1.3.6.1.4.1.33.1.37.1.21 | INTEGER | read-write | The status of the entry. Set to 'disabled' to disable the entry. |
| STR bootRecordMopFile | 1.3.6.1.4.1.33.1.37.1.22 | DisplayString | read-write | The software file name to request for down-line load of the server via MOP or XMOP. |
| IP bootRecordInternetAddress | 1.3.6.1.4.1.33.1.37.1.23 | IpAddress | read-write | The internet address of the system is to use for itself when loading via TFTP. The value 0.0.0.0 indicates default action. |
| INT bootRecordParamTftpDirect | 1.3.6.1.4.1.33.1.37.1.24 | INTEGER | read-write | Control for loading parameters via the protocol DTFTP. Corresponds to SERVER PARAMETER PROTOCOL DTFTP and the presence of 'DTFTP' following the label 'Parameter Protocols Enabled:' in the SERVER BOOT CHARACTERISTICS display. |
| STR bootRecordInternetDelimiter | 1.3.6.1.4.1.33.1.37.1.25 | DisplayString | read-write | The character separating the load file directory name from the file name. |
| INT sysLastAgentError | 1.3.6.1.4.1.33.1.38 | INTEGER | read-only | The most recent error the agent encountered in attempting to satisfy an SNMP request. Reading this value has the side effect of resetting it to 'noError'. |
| INT sysRcpMulticast | 1.3.6.1.4.1.33.1.40 | INTEGER | read-write | Control for sending of the MOP RCP system identifier message. Corresponds directly to the presence of 'RCP Multicast' under the label 'Enabled Characteristics' in the SERVER CHARACTERISTICS display. |
| ADR sysTimeServerAddress | 1.3.6.1.4.1.33.1.41 | TypedAddress | read-only | The address of the time server, either an IpAddr or an ethernet address. |
| ADR sysTimeServerConfiguredAddress | 1.3.6.1.4.1.33.1.46 | TypedAddress | read-write | The address of a configured time server (, either an IpAddr or an ethernet address). |
| INT sysTimeServerConfiguredStatus | 1.3.6.1.4.1.33.1.47 | INTEGER | read-write | Control whether the sysTimeServerConfiguredAddress is the only time server used to obtain the time (REQUIRED), the first time server used to obtain the time (ENABLED), or not used to obtain the time (DISABLED). |
| INT sysBootRecordOverrideDefinedAddress | 1.3.6.1.4.1.33.1.48 | INTEGER | read-write | Control to override the internally defined Internet address with that obtained from the bootp loading protocol. |
| INT sysBootRecordMessageEnable | 1.3.6.1.4.1.33.1.49 | INTEGER | read-write | Control to display load status messages during reboot. Corresponds directly to the value labeled 'Status Message:' in the SERVER LOADDUMP display. |
| INT sysBootRecordParamDefaults | 1.3.6.1.4.1.33.1.50 | INTEGER | read-write | Control to use default parameters upon the next reboot after which time this control reverts to disabled. This control only applies to stand-alone devices. Corresponds directly to the value labeled 'Default Parameters:' in the SERVER LOADDUMP display. |
| INT sysLoginAuthFailureTrapType | 1.3.6.1.4.1.33.1.78 | INTEGER | read-only | Indicates the type of authentication failure which last occurred. |
| STR sysLoginAuthTrapIdentity | 1.3.6.1.4.1.33.1.81 | DisplayString | read-only | An identification string for the circuit or port where an authentication failure last occurred. |
| INT sysLocalScriptServer | 1.3.6.1.4.1.33.1.82 | INTEGER | read-write | Control to allow script serving for this system from a script residing in a local flash card. |
| INT sysInReachManagementSecurityStatus | 1.3.6.1.4.1.33.1.83 | INTEGER | read-only | Indicates whether per port authentication is in use. This includes username, password, privilege level, and list of power outlets controlled by that user, or console connections allowed from that port. |
| STR sysProductName | 1.3.6.1.4.1.33.1.84 | DisplayString | read-only | Displays the product name of this system. |
| INT sysModemPresent | 1.3.6.1.4.1.33.1.85 | INTEGER | read-only | Indicates whether this system has a built-in modem. |
| INT sysCauseAction | 1.3.6.1.4.1.33.1.86 | INTEGER | read-write | A control for toggling the cause action feature. Corresponds directly to the presence of 'Trigger/Action' under the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. The desired change will not take effect until the next system initialization. |
| INT sysWebServerConfigAdminStatus | 1.3.6.1.4.1.33.1.87 | INTEGER | read-write | A control for bring the web server up or down. Corresponds directly to the presence of 'Web Server' under the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| STR sysTl1SourceIdentifier | 1.3.6.1.4.1.33.1.88 | DisplayString | read-write | The source identifier (SID) is the server name used by TL1 to identify the server. |
| INT sysInitializeDelayParameter | 1.3.6.1.4.1.33.1.89 | INTEGER | read-write | Control to begin the system initialization process providing that at least one parameter server is current. Corresponds directly to the INITIALIZE DELAY PARAMETER command. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. |
| INT sysTimeProtocol | 1.3.6.1.4.1.33.1.90 | INTEGER | read-write | Indicates whether the SNTP protocol is used to obtain the time at startup. If disabled, the older TIMED protocol is used. Both protocols run over UDP. |
| INT sysTimeBroadcast | 1.3.6.1.4.1.33.1.91 | INTEGER | read-write | Indicates whether the unit will broadcast for the time at startup. |
RFC description
MRV In-Reach system management including identification and operational modes.
Start monitoring MRV In-Reach terminal/console server (system identity/firmware) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.