MCAST-VPN-MIB

All MIBs › MCAST-VPN-MIB

Organization: IETF Layer-3 Virtual Private Networks Working Group.

Last Updated: 2013-07-12

Category: Standard: IETF, Technology: Multicast, VPN and Security

Description: IETF Layer-3 VPN working group MIB defining SNMP objects for monitoring IP multicast in BGP/MPLS VPN environments per RFC 6513/6514.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is MCAST-VPN-MIB?

MCAST-VPN-MIB is a Juniper Networks build of the standard IETF Layer-3 VPN Working Group MIB (RFC 6517) managing multicast in BGP/MPLS IP VPNs (MVPN). Its objects cover MVRF counts (total, IPv4/IPv6, PIM v4/v6, BGP v4/v6, mLDP), a notification-enable flag, a general table (operational-status-change and change-time, C-multicast route protocol v4/v6, I-PMSI/inter-AS-PMSI config v4/v6, row status), and a BGP-general table (mode, upstream-multihoming (UMH) selection, site type). As a configuration/status MIB it lets an administrator confirm MVPN multicast routing-protocol configuration per VRF on a Juniper PE router. It is deployed on Juniper Networks MPLS/BGP MVPN PE routers. Engineers implementing or auditing this functionality typically reference the MCAST-VPN-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in MCAST-VPN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks MPLS/BGP MVPN PE routers

Monitoring Examples

An administrator checks jnxMvpnBgpGenUmhSelection and jnxMvpnGenCmcastRouteProtocolV4 to confirm MVPN multicast routing configuration on a Juniper PE router.

What Can Be Monitored

MVPN multicast routing-protocol configuration per VRF

Imported Objects

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From IPMROUTE-STD-MIB

ipMRouteEntry

OBJECT-TYPE

From JUNIPER-EXPERIMENT-MIB

jnxMvpnExperiment

OBJECT-IDENTITY

From JUNIPER-SMI

jnxMibs

OBJECT-IDENTITY

From L2L3-VPN-MCAST-MIB

JnxL2L3VpnMcastProviderTunnelType

From MPLS-TC-STD-MIB

MplsLabel

From MPLS-VPN-MIB

MplsVpnRouteDistinguisher
mplsVpnVrfName	OBJECT-TYPE

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowPointer
RowStatus
TimeInterval
TimeStamp
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
jnxMvpnMIB	1.3.6.1.4.1.2636.5.12.1			This MIB contains managed object definitions for multicast in BGP/MPLS IP VPNs defined by [MVPN]. Copyright (C) The Internet Society (2012).
jnxMvpnNotifications	1.3.6.1.4.1.2636.5.12.1.0
NTF jnxMvpnMvrfChange	1.3.6.1.4.1.2636.5.12.1.0.2			A mvpnMvrfChange notification signifies a change about a MVRF in the device. The change event can be creation of the MVRF, deletion of the MVRF or an update on the I-PMSI or S-PMSI configuration of the MVRF. The change event is indicated by mvpnGenOperStatusChange embedded in the notification. The user can then query mvpnGeneralTable, and/or mvpnSpmsiConfigTable to get the details of the change as necessary. Note: Since the creation of a MVRF is often followed by configuration of I-PMSI and/or S-PMSIs for the MVRF, more than one (three at most) notifications for a MVRF may be generated serially, and it is really not necessary to generate all three of them. An agent may choose to generate a notification for the last event only, that is for S-PMSI configuration. Similarly, deletion of I-PMSI and S-PMSI configuration on a MVRF happens before a MVRF is deleted and it is recommended that the agent send the notification for MVRF deletion event only.
jnxMvpnObjects	1.3.6.1.4.1.2636.5.12.1.1
jnxMvpnScalars	1.3.6.1.4.1.2636.5.12.1.1.1
U32 jnxMvpnMvrfNumber	1.3.6.1.4.1.2636.5.12.1.1.1.1	Unsigned32	read-only	The number of MVRFs for IPv4 or IPv6 or mLDP C-Multicast that are present in this device.
U32 jnxMvpnMvrfNumberV4	1.3.6.1.4.1.2636.5.12.1.1.1.2	Unsigned32	read-only	The number of MVRFs for IPv4 C-Multicast that are present in this device.
U32 jnxMvpnMvrfNumberV6	1.3.6.1.4.1.2636.5.12.1.1.1.3	Unsigned32	read-only	The number of MVRFs for IPv6 C-Multicast that are present in this device.
U32 jnxMvpnMvrfNumberPimV4	1.3.6.1.4.1.2636.5.12.1.1.1.4	Unsigned32	read-only	The number of PIM-MVPN MVRFs for IPv4 C-Multicast that are present in this device.
U32 jnxMvpnMvrfNumberPimV6	1.3.6.1.4.1.2636.5.12.1.1.1.5	Unsigned32	read-only	The number of PIM-MVPN MVRFs for IPv6 C-Multicast that are present in this device.
U32 jnxMvpnMvrfNumberBgpV4	1.3.6.1.4.1.2636.5.12.1.1.1.6	Unsigned32	read-only	The number of BGP-MVPN MVRFs for IPv4 C-Multicast that are present in this device.
U32 jnxMvpnMvrfNumberBgpV6	1.3.6.1.4.1.2636.5.12.1.1.1.7	Unsigned32	read-only	The number of BGP-MVPN MVRFs for IPv6 C-Multicast that are present in this device.
U32 jnxMvpnMvrfNumberMldp	1.3.6.1.4.1.2636.5.12.1.1.1.8	Unsigned32	read-only	The number of BGP-MVPN MVRFs for mLDP C-Multicast that are present in this device.
T/F jnxMvpnNotificationEnable	1.3.6.1.4.1.2636.5.12.1.1.1.9	TruthValue	read-only	If this object is TRUE, then the generation of all notifications defined in this MIB is enabled.
jnxMvpnGeneral	1.3.6.1.4.1.2636.5.12.1.1.2
jnxMvpnGeneralTable	1.3.6.1.4.1.2636.5.12.1.1.2.1		not-accessible	This table specifies the general information about the MVRFs present in this device.
jnxMvpnGeneralEntry	1.3.6.1.4.1.2636.5.12.1.1.2.1.1		not-accessible	An entry in this table is created for every MVRF in the device.
INT jnxMvpnGenOperStatusChange	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.1	INTEGER	read-only	This object describes the last operational change that happened for the given MVRF. createdMvrf - indicates that the MVRF was created in the device. deletedMvrf - indicates that the MVRF was deleted from the device. A row in this table will never have mvpnGenOperStatusChange equal to deletedMvrf(2), because in that case the row itself will be deleted from the table. This value for mvpnGenOperStatusChange is defined mainly for use in mvpnMvrfChange notification. modifiedMvrfIpmsiConfig - indicates that the I-PMSI for the MVRF was configured, deleted or changed. modifiedMvrfSpmsiConfig - indicates that the S-PMSI for the MVRF was configured, deleted or changed.
TIM jnxMvpnGenOperChangeTime	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.2	TimeStamp	read-only	The time at which the last operational change for the MVRF in question took place. The last operational change is specified by mvpnGenOperStatusChange.
INT jnxMvpnGenCmcastRouteProtocolV4	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.3	INTEGER	read-only	Protocol used to signal IPv4 C-multicast states across the provider core. pim(1): PIM (PIM-MVPN). bgp(2): BGP (BGP-MVPN).
INT jnxMvpnGenCmcastRouteProtocolV6	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.4	INTEGER	read-only	Protocol used to signal IPv6 C-multicast states across the provider core. pim(1): PIM (PIM-MVPN). bgp(2): BGP (BGP-MVPN).
NUM jnxMvpnGenIpmsiConfigV4	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.5	RowPointer	read-only	This points to a row in MvpnPmsiConfigTable, for I-PMSI configuration for IPv4.
NUM jnxMvpnGenIpmsiConfigV6	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.6	RowPointer	read-only	This points to a row in MvpnPmsiConfigTable, for I-PMSI configuration for IPv6.
NUM jnxMvpnGenInterAsPmsiConfigV4	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.7	RowPointer	read-only	This points to a row in MvpnPmsiConfigTable, for inter-as I-PMSI configuration for IPv4, in case of segmented inter-as provider tunnels.
NUM jnxMvpnGenInterAsPmsiConfigV6	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.8	RowPointer	read-only	This points to a row in MvpnPmsiConfigTable, for inter-as I-PMSI configuration for IPv6, in case of segmented inter-as provider tunnels.
ROW jnxMvpnGenRowStatus	1.3.6.1.4.1.2636.5.12.1.1.2.1.1.9	RowStatus	read-only	This is used to create or delete a row in this table.
jnxMvpnBgpGeneralTable	1.3.6.1.4.1.2636.5.12.1.1.2.2		not-accessible	This table augments the mvpnGeneralTable and is for BGP-MVPN specific information.
jnxMvpnBgpGeneralEntry	1.3.6.1.4.1.2636.5.12.1.1.2.2.1		not-accessible	The mvpnBgpGeneralEntry matches and augments an mvpnGeneralEntry for a BGP-MVPN instance, with BGP-MVPN specific informatoin.
INT jnxMvpnBgpGenMode	1.3.6.1.4.1.2636.5.12.1.1.2.2.1.1	INTEGER	read-only	For two different BGP-MVPN modes: rpt-spt(1): intersite-site shared tree mode spt-only(2): inter-site source-only tree mode.
INT jnxMvpnBgpGenUmhSelection	1.3.6.1.4.1.2636.5.12.1.1.2.2.1.2	INTEGER	read-only	The UMH selection method for this mvpn, as specified in section 5.1.3 of [MVPN]: highest-pe-address (1): PE with the highest address c-root-group-hashing (2): hashing based on (c-root, c-group) uncast-umh-route (3): per ucast route towards c-root
INT jnxMvpnBgpGenSiteType	1.3.6.1.4.1.2636.5.12.1.1.2.2.1.3	INTEGER	read-only	Whether this site is a receiver-only site or not. sender-receiver (1): both sender and receiver site. receiver-only (2): receiver-only site. sender-only (3): sender-only site.
MPL jnxMvpnBgpGenCmcastImportRt	1.3.6.1.4.1.2636.5.12.1.1.2.2.1.4	MplsVpnRouteDistinguisher	read-only	The C-multicast Import RT that this device adds to unicast vpn routes that it advertises for this mvpn.
U32 jnxMvpnBgpGenSrcAs	1.3.6.1.4.1.2636.5.12.1.1.2.2.1.5	Unsigned32	read-only	The Source AS number in Source AS Extended Community that this device adds to the unicast vpn routes that it advertises for this mvpn.
U32 jnxMvpnBgpGenSptnlLimit	1.3.6.1.4.1.2636.5.12.1.1.2.2.1.6	Unsigned32	read-only	The max number of selective provider tunnels this device allows for this mvpn.
jnxMvpnConfig	1.3.6.1.4.1.2636.5.12.1.1.3
jnxMvpnPmsiConfigTable	1.3.6.1.4.1.2636.5.12.1.1.3.1		not-accessible	This table specifies the configured PMSIs.
jnxMvpnPmsiConfigEntry	1.3.6.1.4.1.2636.5.12.1.1.3.1.1		not-accessible	An entry in this table is created for each PMSI configured on this router. It can be referred to by either I-PMSI configuration (in mvpnGeneralEntry) or S-PMSI configuration (in mvpnSpmsiConfigEntry)
JNX jnxMvpnPmsiConfigTunnelType	1.3.6.1.4.1.2636.5.12.1.1.3.1.1.1	JnxL2L3VpnMcastProviderTunnelType	not-accessible	Type of tunnel used to instantiate the PMSI.
U32 jnxMvpnPmsiConfigTunnelAuxInfo	1.3.6.1.4.1.2636.5.12.1.1.3.1.1.2	Unsigned32	not-accessible	Additional tunnel information depending on the type. pim: In case of S-PMSI, number of groups starting at mvpnPmsiConfigTunnelPimGroupAddress. This allows a range of PIM provider tunnel group addresses to be specified in S-PMSI case. In I-PMSI case, it must be 1. rsvp-p2mp: 1 for statically specified rsvp-p2mp tunnel 2 for dynamically created rsvp-p2mp tunnel ingress-replication: 1 for using any existing p2p/mp2p lsp 2 for dynamically creating new p2p lsp
IPt jnxMvpnPmsiConfigTunnelPimGroupAddressType	1.3.6.1.4.1.2636.5.12.1.1.3.1.1.3	InetAddressType	not-accessible	In case of PIM provider tunnel, the type of tunnel address.
IP jnxMvpnPmsiConfigTunnelPimGroupAddress	1.3.6.1.4.1.2636.5.12.1.1.3.1.1.4	InetAddress	not-accessible	In case of PIM provider tunnel, the provider tunnel address.
STR jnxMvpnPmsiConfigTunnelOrTemplateName	1.3.6.1.4.1.2636.5.12.1.1.3.1.1.5	SnmpAdminString	not-accessible	The tunnel name or template name used to create tunnels. Depending on mvpnPmsiConfigTunnelType and mvpnPmsiConfigTunnelAuxInfo: dynamically created rsvp-p2mp tunnel: template name statically specified rsvp-p2mp tunnel: tunnel name ingress-replication using dynamically created lsps: template name other: null
INT jnxMvpnPmsiConfigEncapsType	1.3.6.1.4.1.2636.5.12.1.1.3.1.1.6	INTEGER	read-only	The encapsulation type to be used, in case of PIM tunnel or ingress-replication.
ROW jnxMvpnPmsiConfigRowStatus	1.3.6.1.4.1.2636.5.12.1.1.3.1.1.7	RowStatus	read-only	Used to create/modify/delete a row in this table.
jnxMvpnSpmsiConfigTable	1.3.6.1.4.1.2636.5.12.1.1.3.2		not-accessible	This table specifies S-PMSI configuration.
jnxMvpnSpmsiConfigEntry	1.3.6.1.4.1.2636.5.12.1.1.3.2.1		not-accessible	An entry is created for each S-PMSI configuration.
IPt jnxMvpnSpmsiConfigCmcastAddressType	1.3.6.1.4.1.2636.5.12.1.1.3.2.1.1	InetAddressType	not-accessible	Type of C-multicast address
IP jnxMvpnSpmsiConfigCmcastGroupAddress	1.3.6.1.4.1.2636.5.12.1.1.3.2.1.2	InetAddress	not-accessible	C-multicast group address
U32 jnxMvpnSpmsiConfigCmcastGroupPrefixLen	1.3.6.1.4.1.2636.5.12.1.1.3.2.1.3	Unsigned32	not-accessible	C-multicast group address prefix length. A group 0 (or ::0) with prefix length 32 (or 128) indicates wildcard group, while a group 0 (or ::0) with prefix length 0 indicates any group.
IP jnxMvpnSpmsiConfigCmcastSourceAddress	1.3.6.1.4.1.2636.5.12.1.1.3.2.1.4	InetAddress	not-accessible	C-multicast source address
U32 jnxMvpnSpmsiConfigCmcastSourcePrefixLen	1.3.6.1.4.1.2636.5.12.1.1.3.2.1.5	Unsigned32	read-only	C-multicast source address prefix length. A source 0 (or ::0) with prefix length 32 (or 128) indicates a wildcard source, while a source 0 (or ::0) with prefix length 0 indicates any source.
U32 jnxMvpnSpmsiConfigThreshold	1.3.6.1.4.1.2636.5.12.1.1.3.2.1.6	Unsigned32	read-only	The bandwidth threshold value which when exceeded for a multicast routing entry in the given MVRF, triggers usage of S-PMSI.
NUM jnxMvpnSpmsiConfigPmsiPointer	1.3.6.1.4.1.2636.5.12.1.1.3.2.1.7	RowPointer	read-only	This points to a row in MvpnPmsiConfigTable, to specify tunnel attributes.
ROW jnxMvpnSpmsiConfigRowStatus	1.3.6.1.4.1.2636.5.12.1.1.3.2.1.8	RowStatus	read-only	Used to create/modify/delete a row in this table.
jnxMvpnStates	1.3.6.1.4.1.2636.5.12.1.1.4
jnxMvpnIpmsiTable	1.3.6.1.4.1.2636.5.12.1.1.4.1		not-accessible	This table is for all advertised/received I-PMSI advertisements.
jnxMvpnIpmsiEntry	1.3.6.1.4.1.2636.5.12.1.1.4.1.1		not-accessible	An entry in this table corresponds to an I-PMSI advertisement that is advertised/received on this router. This represents all the sender PEs in the MVPN, with the provider tunnel they use to send traffic.
U32 jnxMvpnIpmsiAfi	1.3.6.1.4.1.2636.5.12.1.1.4.1.1.1	Unsigned32	not-accessible	The address family this I-PMSI is for. 1 - IPv4 2 - IPv6
MPL jnxMvpnIpmsiRD	1.3.6.1.4.1.2636.5.12.1.1.4.1.1.2	MplsVpnRouteDistinguisher	not-accessible	The Route Distinguisher in this I-PMSI.
IPt jnxMvpnIpmsiOrigAddrType	1.3.6.1.4.1.2636.5.12.1.1.4.1.1.3	InetAddressType	not-accessible	The Internet address type of mvpnIpmsiOrigAddress.
IP jnxMvpnIpmsiOrigAddress	1.3.6.1.4.1.2636.5.12.1.1.4.1.1.4	InetAddress	not-accessible	The BGP address of the device that originated the I-PMSI.
NUM jnxMvpnIpmsiUpTime	1.3.6.1.4.1.2636.5.12.1.1.4.1.1.5	TimeInterval	read-only	The time since this I-PMSI was first advertised/received by the device.
NUM jnxMvpnIpmsiAttribute	1.3.6.1.4.1.2636.5.12.1.1.4.1.1.6	RowPointer	read-only	Points to a row in the mvpnPmsiTunnelAttributeTable.
jnxMvpnInterasIpmsiTable	1.3.6.1.4.1.2636.5.12.1.1.4.2		not-accessible	This table is for all advertised/received inter-as I-PMSI advertisements.
jnxMvpnInterasIpmsiEntry	1.3.6.1.4.1.2636.5.12.1.1.4.2.1		not-accessible	An entry in this table corresponds to an inter-as I-PMSI advertisement that is advertised/received on this router. This represents all the ASes in the MVPN, with the provider tunnel used to send traffic to.
U32 jnxMvpnInterasIpmsiAfi	1.3.6.1.4.1.2636.5.12.1.1.4.2.1.1	Unsigned32	not-accessible	The address family this I-PMSI is for. 1 - IPv4 2 - IPv6
MPL jnxMvpnInterasIpmsiRD	1.3.6.1.4.1.2636.5.12.1.1.4.2.1.2	MplsVpnRouteDistinguisher	not-accessible	The Route Distinguisher in this inter-as I-PMSI.
U32 jnxMvpnInterasIpmsiSrcAs	1.3.6.1.4.1.2636.5.12.1.1.4.2.1.3	Unsigned32	not-accessible	The source-as in this inter-as I-PMSI.
NUM jnxMvpnInterasIpmsiAttribute	1.3.6.1.4.1.2636.5.12.1.1.4.2.1.4	RowPointer	read-only	Points to a row in the mvpnPmsiTunnelAttributeTable.
jnxMvpnSpmsiTable	1.3.6.1.4.1.2636.5.12.1.1.4.3		not-accessible	This table has information about the S-PMSIs sent/received by a device.
jnxMvpnSpmsiEntry	1.3.6.1.4.1.2636.5.12.1.1.4.3.1		not-accessible	An entry in this table is created or updated for every S-PMSI advertised/received in a particular MVRF.
IPt jnxMvpnSpmsiOrigAddrType	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.1	InetAddressType	not-accessible	The Internet address type of mvpnSpmsiOrigAddress.
IP jnxMvpnSpmsiOrigAddress	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.2	InetAddress	not-accessible	The BGP address of the device that originated the S-PMSI.
IPt jnxMvpnSpmsiCmcastAddrType	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.3	InetAddressType	not-accessible	The Internet address type of mvpnSpmsiCmcastGroup/Source.
IP jnxMvpnSpmsiCmcastGroup	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.4	InetAddress	not-accessible	S-PMSI C-multicast group address. If it is 0 (or ::0), this is a wildcard group, and mvpnSpmsiCmcastGroupPrefixLen must be 32 (or 128).
U32 jnxMvpnSpmsiCmcastGroupPrefixLen	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.5	Unsigned32	not-accessible	S-PMSI C-multicast group address prefix length.
IP jnxMvpnSpmsiCmcastSource	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.6	InetAddress	not-accessible	S-PMSI C-multicast source address If it is 0 (or ::0), this is a wildcard source, and mvpnSpmsiCmcastSourcePrefixLen must be 32 (or 128).
U32 jnxMvpnSpmsiCmcastSourcePrefixLen	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.7	Unsigned32	not-accessible	S-PMSI C-multicast source address prefix length.
NUM jnxMvpnSpmsiTunnelAttribute	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.8	RowPointer	read-only	A row pointer to the mvpnPmsiTunnelAttributeTable
NUM jnxMvpnSpmsiUpTime	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.9	TimeInterval	read-only	The time since this S-PMSI was first advertised/received by the device.
NUM jnxMvpnSpmsiExpTime	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.10	TimeInterval	read-only	For UDP-based S-PMSI signaling for PIM-MVPN, the amount of time remaining before this received S-PMSI Join Message expires, or the next S-PMSI Join Message refresh is to be advertised again from the device. Otherwise, it is zero.
U32 jnxMvpnSpmsiRefCnt	1.3.6.1.4.1.2636.5.12.1.1.4.3.1.11	Unsigned32	read-only	The number of c-multicast routes that are mapped to this S-PMSI.
jnxMvpnMrouteTable	1.3.6.1.4.1.2636.5.12.1.1.4.4		not-accessible	This table augments ipMcastRouteTable, to provide some MVPN specific information.
jnxMvpnMrouteEntry	1.3.6.1.4.1.2636.5.12.1.1.4.4.1		not-accessible	The mvpnMrouteEntry matches and augments an ipMcastRouteTable, with MVPN specific information, such as PMSI used.
NUM jnxMvpnMroutePmsiPointer	1.3.6.1.4.1.2636.5.12.1.1.4.4.1.1	RowPointer	read-only	The I-PMSI or S-PMSI this C-multicast route is using. This is important because an implementation may not have an interface corresponding to a provider tunnel, that can be used in ipMcastRouteNextHopEntry.
U32 jnxMvpnMrouteNumberOfLocalReplication	1.3.6.1.4.1.2636.5.12.1.1.4.4.1.2	Unsigned32	read-only	Number of replications to local receivers.
U32 jnxMvpnMrouteNumberOfRemoteReplication	1.3.6.1.4.1.2636.5.12.1.1.4.4.1.3	Unsigned32	read-only	Number of (local) replications to remote receivers.
U32 jnxMvpnMrouteDataRate	1.3.6.1.4.1.2636.5.12.1.1.4.4.1.4	Unsigned32	read-only	The data rate for traffic following this route.

RFC description

Manages multicast in BGP/MPLS IP VPNs (MVPN) including provider tunnels and multicast route distribution for virtual private network environments.

Start monitoring Juniper Networks MPLS/BGP MVPN PE router with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download MCAST-VPN-MIB

What Is MCAST-VPN-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description