All MIBs › LaserJet-Series8100-Stapler-MIB › prtoutputmaxdimfeeddir
prtoutputmaxdimfeeddir
Module: LaserJet-Series8100-Stapler-MIB
OID (symbolic): LaserJet-Series8100-Stapler-MIB::prtoutputmaxdimfeeddir
OID (numeric): 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-only
Description: The maximum dimensions supported by this output sub-unit for measurements taken parallel relative to the feed direction associated with that sub-unit in output sub-unit dimensional units (MediaUnit). If this output sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed with management protocol operations. Refer to ftp://ftp.pwg.org/pub/pwg/pmp/drafts/pmib_031698.txt, for more details in the Standard Printer MIB. Additional information: The value returned by this object depends on the value of prtOutputDimUnit. For example, for the built-in output bins, it is 177000 if prtOutputDimUnit is ePtenThousandthsOfInches or 450000 if prtOutputDimUnit is ePmicrometers. 177000 corresponds to the largest custom paper size a Yukon engine can handle. 170000 is the length of Ledger paper, which is the largest an external device can handle, and 85000 is the feed dimension of LETTER paper, which is the largest size the stapler can handle.
What is prtoutputmaxdimfeeddir?
This reports the maximum media dimension this output sub-unit supports measured parallel to the paper feed direction, in the units set by prtoutputdimunit. An admin uses this to know the largest paper length a given output bin can accept, since sensor-derived values on this object can't be changed via SNMP. For example, the built-in bins return 177000 (in ePtenThousandthsOfInches units), corresponding to the largest custom paper size the base engine can handle, while the stapler unit is limited to 85000, the feed-direction size of Letter paper.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15 snmpwalk -v2c -c public <target> LaserJet-Series8100-Stapler-MIB::prtoutputmaxdimfeeddir
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15.1 snmpget -v2c -c public <target> LaserJet-Series8100-Stapler-MIB::prtoutputmaxdimfeeddir.1
Start monitoring HP LaserJet 8100 series printer with stapler/finisher accessory with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the LaserJet-Series8100-Stapler-MIB::prtoutputmaxdimfeeddir OID value, configure state conditions and alerts, and monitor any HP LaserJet 8100 series printer with stapler/finisher accessory from a single console.
OID Breakdown
Upper-level ancestors (16 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.11 | hp | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2 | nm | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3 | hpsystem | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9 | net_peripheral | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4 | netdm | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2 | dm | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2.2 | printmib | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9 | prtOutput | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2 | prtOutputTable | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1 | prtOutputEntry | CLJ8500-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15 | prtoutputmaxdimfeeddir | LaserJet-Series8100-Stapler-MIB |