All MIBs › LaserJet-Series8000-Stapler-MIB › prtoutputmaxdimfeeddir
prtoutputmaxdimfeeddir
Module: LaserJet-Series8000-Stapler-MIB
OID (symbolic): LaserJet-Series8000-Stapler-MIB::prtoutputmaxdimfeeddir
OID (numeric): 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-only
Description: The maximum dimensions supported by this output sub-unit for measurements taken parallel relative to the feed direction associated with that sub-unit in output sub-unit dimensional units (MediaUnit). If this output sub-unit can reliably sense this value, the value is sensed by the printer and may not be changed with management protocol operations. Refer to ftp://ftp.pwg.org/pub/pwg/pmp/drafts/pmib_031698.txt, for more details in the Standard Printer MIB. Additional information: The value returned by this object depends on the value of prtOutputDimUnit. For example, for the built-in output bins, it is 177000 if prtOutputDimUnit is ePtenThousandthsOfInches or 450000 if prtOutputDimUnit is ePmicrometers. 177000 corresponds to the largest custom paper size a Yukon engine can handle. 170000 is the length of Ledger paper, which is the largest an external device can handle, and 85000 is the feed dimension of LETTER paper, which is the largest size the stapler can handle.
What is prtoutputmaxdimfeeddir?
The longest sheet length, measured in the feed direction, that this output bin can physically accept, expressed in the units given by prtoutputdimunit. Since the value differs by bin type -- built-in bins handle up to Ledger-length paper while the stapler module is limited to Letter-length -- an admin can use it to confirm a bin will accept a given job's paper size before routing print jobs there. For example, the stapler's output sub-unit reports 85000 (ten-thousandths of an inch), meaning it can't accept anything longer than Letter-size paper.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15 snmpwalk -v2c -c public <target> LaserJet-Series8000-Stapler-MIB::prtoutputmaxdimfeeddir
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15.1 snmpget -v2c -c public <target> LaserJet-Series8000-Stapler-MIB::prtoutputmaxdimfeeddir.1
Start monitoring HP LaserJet 8000 series printer with stapler/finisher accessory with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the LaserJet-Series8000-Stapler-MIB::prtoutputmaxdimfeeddir OID value, configure state conditions and alerts, and monitor any HP LaserJet 8000 series printer with stapler/finisher accessory from a single console.
OID Breakdown
Upper-level ancestors (16 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.11 | hp | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2 | nm | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3 | hpsystem | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9 | net_peripheral | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4 | netdm | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2 | dm | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2.2 | printmib | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9 | prtOutput | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2 | prtOutputTable | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1 | prtOutputEntry | CLJ8500-MIB |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.11.2.3.9.4.2.2.9.2.1.15 | prtoutputmaxdimfeeddir | LaserJet-Series8000-Stapler-MIB |