All MIBs › Juniper-IP-MIB › juniIpIfInitSeqPrefOper
juniIpIfInitSeqPrefOper
Module: Juniper-IP-MIB
OID (symbolic): Juniper-IP-MIB::juniIpIfInitSeqPrefOper
OID (numeric): 1.3.6.1.4.1.4874.2.2.12.1.1.2.1.32
Node type: OBJECT-TYPE
Type: Unsigned32
Access: read-only
Description: Indicates the operational warm-restart replay initial sequence preference value for an IP interface. Following an HA SRP switchover, high-preference (value 1) IP interfaces are replayed first, followed by static routes, and then low-preference (value 0) IP interfaces. This allows static routes that are dependent on high-preference interfaces to be resolved and routing protocols to exchange information with peers over high-preference interfaces before low-preference interfaces are replayed. An IP interface is designated as high-preference either (1) implicitly by configuring an IGP or PIM protocol on that interface, or (2) explicitly by juniIpIfInitSeqPrefAdmin (or CLI) configuration.
What is juniIpIfInitSeqPrefOper?
Reports the operational warm-restart replay preference for this interface: high-preference (1) interfaces are replayed first after an HA switchover (before static routes and low-preference interfaces), so routing protocols can re-establish over them sooner.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.4874.2.2.12.1.1.2.1.32 snmpwalk -v2c -c public <target> Juniper-IP-MIB::juniIpIfInitSeqPrefOper
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.4874.2.2.12.1.1.2.1.32.1 snmpget -v2c -c public <target> Juniper-IP-MIB::juniIpIfInitSeqPrefOper.1
Start monitoring Juniper Networks E-series broadband router (IPv4 routing/addressing) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the Juniper-IP-MIB::juniIpIfInitSeqPrefOper OID value, configure state conditions and alerts, and monitor any Juniper Networks E-series broadband router (IPv4 routing/addressing) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.4874 | juniperUni | Juniper-UNI-SMI |
| 1.3.6.1.4.1.4874.2 | juniperUniMibs | Juniper-UNI-SMI |
| 1.3.6.1.4.1.4874.2.2 | juniMibs | Juniper-MIBs |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.4874.2.2.12 | juniIpMIB | Juniper-IP-MIB |
| 1.3.6.1.4.1.4874.2.2.12.1 | juniIpObjects | Juniper-IP-MIB |
| 1.3.6.1.4.1.4874.2.2.12.1.1 | juniIpInterface | Juniper-IP-MIB |
| 1.3.6.1.4.1.4874.2.2.12.1.1.2 | juniIpIfTable | Juniper-IP-MIB |
| 1.3.6.1.4.1.4874.2.2.12.1.1.2.1 | juniIpIfEntry | Juniper-IP-MIB |
| 1.3.6.1.4.1.4874.2.2.12.1.1.2.1.32 | juniIpIfInitSeqPrefOper | Juniper-IP-MIB |