All MIBs › JUNIPER-IFOPTICS-MIB
Organization: Juniper Networks, Inc.
Last Updated: 2012-01-26
Category: Network Interfaces, Optical and WDM, Vendor: Juniper
Description: Provides managed objects for optical transceiver monitoring on Juniper Networks interfaces, including power levels, temperature, and diagnostics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is JUNIPER-IFOPTICS-MIB?
JUNIPER-IFOPTICS-MIB is a Juniper Networks vendor MIB for managing optical transceiver interfaces (the Optics interface layer) on Juniper routers and switches, commonly used for DWDM/coherent optical modules. It exposes optics configuration (per-interface config table), optical trace-tone settings, notification trigger hold-time parameters, and performance-monitoring (PM) data collected both as a current snapshot and over historical intervals. Its core use is hardware health and performance monitoring of optical interfaces — tracking signal quality/performance metrics over time and raising alarms via configurable notification triggers when optical parameters degrade, which is critical for detecting fiber degradation or transceiver failure before it causes an outage. It depends on Juniper's broader jnx enterprise MIB tree (e.g. interface indexing conventions shared with other Juniper interface MIBs) and standard SNMP notification mechanisms. It is deployed on Juniper routers and switches with pluggable optical modules in service-provider and enterprise core/edge networks, where JUNIPER-IFOPTICS-MIB SNMP monitoring of optical parameters helps prevent unplanned outages.
IPNetwork Monitor allows you to monitor SNMP objects defined in JUNIPER-IFOPTICS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Juniper router or switch with pluggable optical/DWDM transceivers
Monitoring Examples
An operator would poll jnxOpticsPMCurrentTable/jnxOpticsPMCurrentEntry for real-time optical performance-monitoring metrics on a given interface, and compare against jnxOpticsPMIntervalTable/jnxOpticsPMIntervalEntry historical bins to spot a gradual degradation trend. jnxOpticsNotificationTrigTable entries, tuned via jnxOpticsNotificationTrigDefaultHoldtimeUp/Down, determine how long a fault condition must persist before jnxOpticsAlarm notifications fire, letting an admin avoid alerting on transient optical flicker while still catching sustained signal-quality drops.
What Can Be Monitored
- optics configuration per interface
- current optical performance metrics
- historical interval performance data
- alarm/notification hold-time thresholds
- trace-tone configuration
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifDescr | OBJECT-TYPE |
| ifIndex | OBJECT-TYPE |
From JUNIPER-SMI
| jnxOpticsMibRoot | OBJECT-IDENTITY |
| jnxOpticsNotifications | OBJECT-IDENTITY |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| TEXTUAL-CONVENTION | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| jnxIfOpticsMib | 1.3.6.1.4.1.2636.3.71.1 | This MIB module defines objects used for managing the Optics interface for Juniper products. | ||
| jnxOptics | 1.3.6.1.4.1.2636.3.71.1.1 | |||
| jnxOpticsConfigTable | 1.3.6.1.4.1.2636.3.71.1.1.1 | not-accessible | Information about the optics config Table. | |
| jnxOpticsConfigEntry | 1.3.6.1.4.1.2636.3.71.1.1.1.1 | not-accessible | A conceptual row that contains information about the optics config Table. | |
| I32 jnxOpticsConfigContainerIndex | 1.3.6.1.4.1.2636.3.71.1.1.1.1.1 | Integer32 | not-accessible | The associated jnxContentsContainerIndex - eg shelf.. |
| I32 jnxOpticsConfigL1Index | 1.3.6.1.4.1.2636.3.71.1.1.1.1.2 | Integer32 | not-accessible | The level one index associated with this subject ... eg fpc slot. |
| I32 jnxOpticsConfigL2Index | 1.3.6.1.4.1.2636.3.71.1.1.1.1.3 | Integer32 | not-accessible | The level two index associated with this subject .. eg pic slot. |
| I32 jnxOpticsConfigL3Index | 1.3.6.1.4.1.2636.3.71.1.1.1.1.4 | Integer32 | not-accessible | The level three index associated with this subject.. eg port. |
| I32 jnxOpticsType | 1.3.6.1.4.1.2636.3.71.1.1.1.1.5 | Integer32 | read-only | 0 - none 1 - SFP 2 - XFP 3 - SFP+ 4 - XFP+ 5 - CFP 6 - CFP+ 7 - Non pluggable |
| T/F jnxLaserEnable | 1.3.6.1.4.1.2636.3.71.1.1.1.1.6 | TruthValue | read-write | 0 - laser off 1 - laser on |
| U32 jnxWavelength | 1.3.6.1.4.1.2636.3.71.1.1.1.1.7 | Unsigned32 | read-write | The transmit wavelength of the laser. |
| JNX jnxSpacing | 1.3.6.1.4.1.2636.3.71.1.1.1.1.8 | JnxOpticsChannelSpacing | read-only | A minimum nominal difference in frequency (GHz) between two adjacent channels. |
| U32 jnxModulation | 1.3.6.1.4.1.2636.3.71.1.1.1.1.9 | Unsigned32 | read-only | Modulation Unknown - (1), NonPSK - (2), ODB - (3), DPSK - (4), QPSK - (5), DQPSK - (6), DPQPSK - (7), 16QAM - (8), 64QAM - (9), 256QAM - (10) |
| I32 jnxTxOpticalPower | 1.3.6.1.4.1.2636.3.71.1.1.1.1.10 | Integer32 | read-write | Transmit optical power. |
| I32 jnxRxOpticalPower | 1.3.6.1.4.1.2636.3.71.1.1.1.1.11 | Integer32 | read-only | Receive optical power. |
| I32 jnxModuleTempHighThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.12 | Integer32 | read-only | High module temerature in degree fahrenheit for a 15 minute period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnxModuleTempLowThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.13 | Integer32 | read-only | Low module temerature in degree fahrenheit for a 15 minute period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnxTxPowerHighThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.14 | Integer32 | read-write | Tx power for a 15 minute period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnxTxPowerLowThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.15 | Integer32 | read-write | Tx Power for a 15 minute period below which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnxRxPowerHighThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.16 | Integer32 | read-write | Rx power for a 15 minute period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnxRxPowerLowThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.17 | Integer32 | read-write | Rx Power for a 15 minute period below which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnx24HourModuleTempHighThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.18 | Integer32 | read-only | High module temerature in degree fahrenheit for a 24 hour period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnx24HourModuleTempLowThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.19 | Integer32 | read-only | Low module temerature in degree fahrenheit for a 24 hour period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnx24HourTxPowerHighThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.20 | Integer32 | read-write | Tx power for a 24 hour period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnx24HourTxPowerLowThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.21 | Integer32 | read-write | Tx for a 24 hour period Power below which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnx24HourRxPowerHighThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.22 | Integer32 | read-write | Rx power for a 24 hour period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnx24HourRxPowerLowThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.23 | Integer32 | read-write | Rx Power for a 24 hour period below which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnxRxLosPowerWarningThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.24 | Integer32 | read-write | Rx Power warning threshold for seeting the optical LOS warning. |
| I32 jnxRxLosPowerAlarmThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.25 | Integer32 | read-write | Rx Power alarm threshold for seeting the optical LOS warning. |
| BIT jnxOpticsCurrentStatus | 1.3.6.1.4.1.2636.3.71.1.1.1.1.26 | Bits | read-only | |
| T/F jnxTxPowerHighEnableTCA | 1.3.6.1.4.1.2636.3.71.1.1.1.1.27 | TruthValue | read-write | Enable/Disable for the Tx Power High TCA. |
| T/F jnxTxPowerLowEnableTCA | 1.3.6.1.4.1.2636.3.71.1.1.1.1.28 | TruthValue | read-write | Enable/Disable for the Tx Power Low TCA. |
| T/F jnxRxPowerHighEnableTCA | 1.3.6.1.4.1.2636.3.71.1.1.1.1.29 | TruthValue | read-write | Enable/Disable for the Rx Power High TCA. |
| T/F jnxRxPowerLowEnableTCA | 1.3.6.1.4.1.2636.3.71.1.1.1.1.30 | TruthValue | read-write | Enable/Disable for the Rx Power Low TCA. |
| T/F jnxModuleTempHighEnableTCA | 1.3.6.1.4.1.2636.3.71.1.1.1.1.31 | TruthValue | read-write | Enable/Disable for the Module Temp High TCA. |
| T/F jnxModuleTempLowEnableTCA | 1.3.6.1.4.1.2636.3.71.1.1.1.1.32 | TruthValue | read-write | Enable/Disable for the Module Temp Low TCA. |
| T/F jnxCarFreqOffsetHighEnableTCA | 1.3.6.1.4.1.2636.3.71.1.1.1.1.33 | TruthValue | read-write | Enable/Disable for the Carrier Frequency Offset High TCA. |
| T/F jnxCarFreqOffsetLowEnableTCA | 1.3.6.1.4.1.2636.3.71.1.1.1.1.34 | TruthValue | read-write | Enable/Disable for the CarrierFreqOffetLow TCA's. |
| I32 jnxCarFreqOffsetHighThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.35 | Integer32 | read-write | Carrier frequency offset for a 15 minute period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnx24HourCarFreqOffsetHighThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.36 | Integer32 | read-write | Carrier frequency offset for a 24 Hour period above which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnxCarFreqOffsetLowThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.37 | Integer32 | read-write | Carrier frequency offset for a 15 minute period Low which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| I32 jnx24HourCarFreqOffsetLowThresh | 1.3.6.1.4.1.2636.3.71.1.1.1.1.38 | Integer32 | read-write | Carrier frequency offset for a 24 Hour period Low which a Threshold Crossing Alert (TCA) should be sent. Only one TCA will be sent per period . |
| jnxOpticsTraceToneCfgTable | 1.3.6.1.4.1.2636.3.71.1.1.2 | not-accessible | Information about the optics tests. | |
| jnxOpticsTraceToneCfgEntry | 1.3.6.1.4.1.2636.3.71.1.1.2.1 | not-accessible | Information about the optics FRU's. | |
| I32 jnxOpticsTraceToneCfgContainerIndex | 1.3.6.1.4.1.2636.3.71.1.1.2.1.1 | Integer32 | not-accessible | The associated jnxContentsContainerIndex - eg shelf.. |
| I32 jnxOpticsTraceToneCfgL1Index | 1.3.6.1.4.1.2636.3.71.1.1.2.1.2 | Integer32 | not-accessible | The level one index associated with this subject ... eg fpc slot. |
| I32 jnxOpticsTraceToneCfgL2Index | 1.3.6.1.4.1.2636.3.71.1.1.2.1.3 | Integer32 | not-accessible | The level two index associated with this subject .. eg pic slot. |
| I32 jnxOpticsTraceToneCfgL3Index | 1.3.6.1.4.1.2636.3.71.1.1.2.1.4 | Integer32 | not-accessible | The level three index associated with this subject.. eg port. |
| T/F jnxOpticsTraceToneCfgTxEnable | 1.3.6.1.4.1.2636.3.71.1.1.2.1.5 | TruthValue | read-write | This will enable/disable the transmit Trace tone feature. |
| T/F jnxOpticsTraceToneCfgRxEnable | 1.3.6.1.4.1.2636.3.71.1.1.2.1.6 | TruthValue | read-write | This will enable/disable the receive Trace tone feature. |
| OCT jnxOpticsTraceToneCfgDestId | 1.3.6.1.4.1.2636.3.71.1.1.2.1.7 | OCTET STRING | read-write | This is the destination Id of the link ID/ the chassis and the blade. The transmit messages will also have the src id which is this chassis id and this port info. |
| OCT jnxOpticsTraceToneCfgTxMsg | 1.3.6.1.4.1.2636.3.71.1.1.2.1.8 | OCTET STRING | read-write | This will be the transmit data in the tracetone message. |
| OCT jnxOpticsTraceToneCfgRxMsg | 1.3.6.1.4.1.2636.3.71.1.1.2.1.9 | OCTET STRING | read-only | This will be the receive data in the trace tone message. |
| I32 jnxOpticsNotificationTrigDefaultHoldtimeUp | 1.3.6.1.4.1.2636.3.71.1.1.3 | Integer32 | read-write | This object will indicate the time (ms) for the defect to persist before it is declared an alarm. |
| I32 jnxOpticsNotificationTrigDefaultHoldtimeDown | 1.3.6.1.4.1.2636.3.71.1.1.4 | Integer32 | read-write | This object will indicate the time (ms) for the defect to absent before the alarm is cleared. |
| jnxOpticsNotificationTrigTable | 1.3.6.1.4.1.2636.3.71.1.1.5 | not-accessible | Information about the otn Alarm/Alart/Info trigger table. | |
| jnxOpticsNotificationTrigEntry | 1.3.6.1.4.1.2636.3.71.1.1.5.1 | not-accessible | A conceptual row that contains information about the Otn Alarm Trigger Table. | |
| I32 jnxOpticsNotificationTrigContainerIndex | 1.3.6.1.4.1.2636.3.71.1.1.5.1.1 | Integer32 | not-accessible | The associated jnxContentsContainerIndex - eg shelf. |
| I32 jnxOpticsNotificationTrigL1Index | 1.3.6.1.4.1.2636.3.71.1.1.5.1.2 | Integer32 | not-accessible | The level one index associated with this subject ... eg fpc slot. |
| I32 jnxOpticsNotificationTrigL2Index | 1.3.6.1.4.1.2636.3.71.1.1.5.1.3 | Integer32 | not-accessible | The level two index associated with this subject .. eg pic slot. |
| I32 jnxOpticsNotificationTrigL3Index | 1.3.6.1.4.1.2636.3.71.1.1.5.1.4 | Integer32 | not-accessible | The level three index associated with this subject.. eg port. |
| JNX jnxOpticsNotificationTrigAlmId | 1.3.6.1.4.1.2636.3.71.1.1.5.1.5 | JnxOpticsNotificationId | not-accessible | This will be the type of Alarm as defined by JnxOpticsNotificationId |
| JNX jnxOpticsNotificationTrigSeverity | 1.3.6.1.4.1.2636.3.71.1.1.5.1.6 | JnxOpticsSeverity | read-write | This will be the Severity of the Notification. |
| T/F jnxOpticsNotificationTrigIgnore | 1.3.6.1.4.1.2636.3.71.1.1.5.1.7 | TruthValue | read-write | This object will ignore the alarm when set. |
| I32 jnxOpticsNotificationTrigHoldtimeUp | 1.3.6.1.4.1.2636.3.71.1.1.5.1.8 | Integer32 | read-write | This object will indicate the time (ms) for the defect to persist before it is declared an alarm. |
| I32 jnxOpticsNotificationTrigHoldtimeDown | 1.3.6.1.4.1.2636.3.71.1.1.5.1.9 | Integer32 | read-write | This object will indicate the time (ms) the defect is absent before the alarm is cleared. |
| JNX jnxOpticsTrigServiceStateAction | 1.3.6.1.4.1.2636.3.71.1.1.5.1.10 | JnxOpticsServiceStateAction | read-only | This will indicate whether this alarm is service affecting or not . |
| T/F jnxOpticsClearAllPMs | 1.3.6.1.4.1.2636.3.71.1.1.6 | TruthValue | read-write | To clear all optics Performance monitoring counters on all interfaces. |
| jnxOpticsClearIfPMsTable | 1.3.6.1.4.1.2636.3.71.1.1.7 | not-accessible | To clear optics Performance monitoring counters on this interfaces | |
| jnxOpticsClearIfPMsEntry | 1.3.6.1.4.1.2636.3.71.1.1.7.1 | not-accessible | A conceptual row that s used to clear the Optics PM Table. | |
| T/F jnxOpticsClearCurrent | 1.3.6.1.4.1.2636.3.71.1.1.7.1.1 | TruthValue | read-write | 1- to clear all the Current Optics PM's for this interface |
| T/F jnxOpticsClearInterfaceInterval | 1.3.6.1.4.1.2636.3.71.1.1.7.1.2 | TruthValue | read-write | 1- to clear all the Optics PM's intervals(1-96) for this interface |
| T/F jnxOpticsClearInterfaceDay | 1.3.6.1.4.1.2636.3.71.1.1.7.1.3 | TruthValue | read-write | 1 - to clear all the Current Day and Previous Day Optics PM's for this interface |
| T/F jnxOpticsClearInterfaceAll | 1.3.6.1.4.1.2636.3.71.1.1.7.1.4 | TruthValue | read-write | 1 - to clear all the Optics PM's for this interface |
| jnxOpticsPerformanceMonitoring | 1.3.6.1.4.1.2636.3.71.1.2 | |||
| jnxOpticsPMCurrentTable | 1.3.6.1.4.1.2636.3.71.1.2.1 | not-accessible | A table of current PM entries. | |
| jnxOpticsPMCurrentEntry | 1.3.6.1.4.1.2636.3.71.1.2.1.1 | not-accessible | A conceptual row that contains information about the PM Current Table. | |
| I32 jnxPMCurChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.1.1.1 | Integer32 | read-only | Residual Chromatic Dispersion measured at Rx Transceiver port |
| I32 jnxPMCurDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.1.1.2 | Integer32 | read-only | Differential group delay |
| I32 jnxPMCurPolarizationState | 1.3.6.1.4.1.2636.3.71.1.2.1.1.3 | Integer32 | read-only | Polarization state |
| I32 jnxPMCurPolarDepLoss | 1.3.6.1.4.1.2636.3.71.1.2.1.1.4 | Integer32 | read-only | The polarisation dependent loss (PDL) is the difference (in dB) between the maximum and minimum values of the channel insertion loss (or gain) of the black-link from point SS to RS due to a variation of the state of polarization (SOP) over all SOPs |
| I32 jnxPMCurQ | 1.3.6.1.4.1.2636.3.71.1.2.1.1.5 | Integer32 | read-only | 'Q' factor estimated at Rx Transceiver port |
| I32 jnxPMCurSNR | 1.3.6.1.4.1.2636.3.71.1.2.1.1.6 | Integer32 | read-only | SNR - signal to noise ratio |
| I32 jnxPMCurTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.1.1.7 | Integer32 | read-only | TxOutputPower - transmit output power |
| I32 jnxPMCurRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.1.1.8 | Integer32 | read-only | RxInputPower - receive output power |
| I32 jnxPMCurMinChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.1.1.9 | Integer32 | read-only | Min Residual Chromatic Dispersion measured at Rx Transceiver port |
| I32 jnxPMCurMaxChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.1.1.10 | Integer32 | read-only | Max Residual Chromatic Dispersion measured at Rx Transceiver port |
| I32 jnxPMCurAvgChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.1.1.11 | Integer32 | read-only | Average Residual Chromatic Dispersion measured at Rx Transceiver port |
| I32 jnxPMCurMinDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.1.1.12 | Integer32 | read-only | Min Differential group delay |
| I32 jnxPMCurMaxDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.1.1.13 | Integer32 | read-only | Max Differential group delay |
| I32 jnxPMCurAvgDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.1.1.14 | Integer32 | read-only | Average Differential group delay |
| I32 jnxPMCurMinPolarState | 1.3.6.1.4.1.2636.3.71.1.2.1.1.15 | Integer32 | read-only | Min Polarization state |
| I32 jnxPMCurMaxPolarState | 1.3.6.1.4.1.2636.3.71.1.2.1.1.16 | Integer32 | read-only | Max Polarization state |
| I32 jnxPMCurAvgPolarState | 1.3.6.1.4.1.2636.3.71.1.2.1.1.17 | Integer32 | read-only | Avg Polarization state |
| I32 jnxPMCurMinPolarDepLoss | 1.3.6.1.4.1.2636.3.71.1.2.1.1.18 | Integer32 | read-only | Min - The polarisation dependent loss (PDL) |
| I32 jnxPMCurMaxPolarDepLoss | 1.3.6.1.4.1.2636.3.71.1.2.1.1.19 | Integer32 | read-only | Max - The polarisation dependent loss (PDL) |
| I32 jnxPMCurAvgPolarDepLoss | 1.3.6.1.4.1.2636.3.71.1.2.1.1.20 | Integer32 | read-only | Avg - The polarisation dependent loss (PDL) |
| I32 jnxPMCurMinQ | 1.3.6.1.4.1.2636.3.71.1.2.1.1.21 | Integer32 | read-only | Min 'Q' factor estimated at Rx Transceiver port |
| I32 jnxPMCurMaxQ | 1.3.6.1.4.1.2636.3.71.1.2.1.1.22 | Integer32 | read-only | Max 'Q' factor estimated at Rx Transceiver port |
| I32 jnxPMCurAvgQ | 1.3.6.1.4.1.2636.3.71.1.2.1.1.23 | Integer32 | read-only | Avg 'Q' factor estimated at Rx Transceiver port |
| I32 jnxPMCurMinSNR | 1.3.6.1.4.1.2636.3.71.1.2.1.1.24 | Integer32 | read-only | Min SNR - signal to noise ratio |
| I32 jnxPMCurMaxSNR | 1.3.6.1.4.1.2636.3.71.1.2.1.1.25 | Integer32 | read-only | Max SNR - signal to noise ratio |
| I32 jnxPMCurAvgSNR | 1.3.6.1.4.1.2636.3.71.1.2.1.1.26 | Integer32 | read-only | Avg SNR - signal to noise ratio |
| I32 jnxPMCurMinTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.1.1.27 | Integer32 | read-only | Min TxOutputPower - transmit output power |
| I32 jnxPMCurMaxTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.1.1.28 | Integer32 | read-only | Max TxOutputPower - transmit output power |
| I32 jnxPMCurAvgTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.1.1.29 | Integer32 | read-only | Avg TxOutputPower - transmit output power |
| I32 jnxPMCurMinRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.1.1.30 | Integer32 | read-only | Min RxInputPower - receive output power |
| I32 jnxPMCurMaxRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.1.1.31 | Integer32 | read-only | Max RxInputPower - receive output power |
| I32 jnxPMCurAvgRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.1.1.32 | Integer32 | read-only | Avg RxInputPower - receive output power |
| T/F jnxPMCurSuspectedFlag | 1.3.6.1.4.1.2636.3.71.1.2.1.1.33 | TruthValue | read-only | If true, the data in this entry may be unreliable. |
| I32 jnxPMCurSuspectReason | 1.3.6.1.4.1.2636.3.71.1.2.1.1.34 | Integer32 | read-only | If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts |
| I32 jnxPMCurTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.1.1.35 | Integer32 | read-only | Trasmit LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMCurMinTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.1.1.36 | Integer32 | read-only | Minimum trasmit LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMCurMaxTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.1.1.37 | Integer32 | read-only | Maximum trasmit LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMCurAvgTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.1.1.38 | Integer32 | read-only | Average LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMCurTemperature | 1.3.6.1.4.1.2636.3.71.1.2.1.1.39 | Integer32 | read-only | Temperature measured at Transceiver port |
| I32 jnxPMCurMinTemperature | 1.3.6.1.4.1.2636.3.71.1.2.1.1.40 | Integer32 | read-only | Minimum Temperature measured at Transceiver port |
| I32 jnxPMCurMaxTemperature | 1.3.6.1.4.1.2636.3.71.1.2.1.1.41 | Integer32 | read-only | Maximum Temperature measure at Transceiver port |
| I32 jnxPMCurAvgTemperature | 1.3.6.1.4.1.2636.3.71.1.2.1.1.42 | Integer32 | read-only | Average Temperature measure at Transceiver port |
| I32 jnxPMCurCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.1.1.43 | Integer32 | read-only | Carrier frequency offset measured at Transceiver port |
| I32 jnxPMCurMinCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.1.1.44 | Integer32 | read-only | Minimum Carrier frequency offset measured at Transceiver port |
| I32 jnxPMCurMaxCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.1.1.45 | Integer32 | read-only | Maximum Carrier frequency offset measured at Transceiver port |
| I32 jnxPMCurAvgCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.1.1.46 | Integer32 | read-only | Average Carrier frequency offset measured at Transceiver port |
| I32 jnxPMCurRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.1.1.47 | Integer32 | read-only | Received LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMCurMinRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.1.1.48 | Integer32 | read-only | Received Minimum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMCurMaxRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.1.1.49 | Integer32 | read-only | Received Maximum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMCurAvgRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.1.1.50 | Integer32 | read-only | Received Average LaserBiasCurrent measured at Transceiver port |
| jnxOpticsPMIntervalTable | 1.3.6.1.4.1.2636.3.71.1.2.2 | not-accessible | A table of current PM entries. | |
| jnxOpticsPMIntervalEntry | 1.3.6.1.4.1.2636.3.71.1.2.2.1 | not-accessible | A conceptual row that contains information about the PM Interval Table. | |
| U32 jnxOpticsPMIntervalNumber | 1.3.6.1.4.1.2636.3.71.1.2.2.1.1 | Unsigned32 | not-accessible | This is the 15 mintute interavl number. |
| I32 jnxPMIntMinChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.2.1.2 | Integer32 | read-only | Residual Chromatic Dispersion measured at Rx Transceiver port - min in the 15 minute interval |
| I32 jnxPMIntMaxChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.2.1.3 | Integer32 | read-only | Residual Chromatic Dispersion measured at Rx Transceiver port - max in the 15 minute interval |
| I32 jnxPMIntAvgChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.2.1.4 | Integer32 | read-only | Residual Chromatic Dispersion measured at Rx Transceiver port - average in the 15 minute interval |
| I32 jnxPMIntMinDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.2.1.5 | Integer32 | read-only | Differential group delay measured at Rx Transceiver port -- min in the 15 minute interval |
| I32 jnxPMIntMaxDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.2.1.6 | Integer32 | read-only | Differential group delay measured at Rx Transceiver port -- max in the 15 minute interval |
| I32 jnxPMIntAvgDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.2.1.7 | Integer32 | read-only | Differential group delay measured at Rx Transceiver port -- average in the 15 minute interval |
| I32 jnxPMIntMinPolarState | 1.3.6.1.4.1.2636.3.71.1.2.2.1.8 | Integer32 | read-only | Polarization state -- min in the 15 minute interval |
| I32 jnxPMIntMaxPolarState | 1.3.6.1.4.1.2636.3.71.1.2.2.1.9 | Integer32 | read-only | Polarization state -- max in the 15 minute interval |
| I32 jnxPMIntAvgPolarState | 1.3.6.1.4.1.2636.3.71.1.2.2.1.10 | Integer32 | read-only | Polarization state -- average in the 15 minute interval |
| I32 jnxPMIntMinPolarDependentLoss | 1.3.6.1.4.1.2636.3.71.1.2.2.1.11 | Integer32 | read-only | Polarization Dependent Loss -- min in the 15 minute interval |
| I32 jnxPMIntMaxPolarDependentLoss | 1.3.6.1.4.1.2636.3.71.1.2.2.1.12 | Integer32 | read-only | Polarization Dependent Loss -- max in the 15 minute interval |
| I32 jnxPMIntAvgPolarDependentLoss | 1.3.6.1.4.1.2636.3.71.1.2.2.1.13 | Integer32 | read-only | Polarization Dependent Loss -- average in the 15 minute interval |
| I32 jnxPMIntMinQ | 1.3.6.1.4.1.2636.3.71.1.2.2.1.14 | Integer32 | read-only | Q -- min in the 15 minute interval |
| I32 jnxPMIntMaxQ | 1.3.6.1.4.1.2636.3.71.1.2.2.1.15 | Integer32 | read-only | Q -- max in the 15 minute interval |
| I32 jnxPMIntAvgQ | 1.3.6.1.4.1.2636.3.71.1.2.2.1.16 | Integer32 | read-only | Q -- Avg in the 15 minute interval |
| I32 jnxPMIntMinSNR | 1.3.6.1.4.1.2636.3.71.1.2.2.1.17 | Integer32 | read-only | SNR -- min in the 15 minute interval |
| I32 jnxPMIntMaxSNR | 1.3.6.1.4.1.2636.3.71.1.2.2.1.18 | Integer32 | read-only | SNR -- max in the 15 minute interval |
| I32 jnxPMIntAvgSNR | 1.3.6.1.4.1.2636.3.71.1.2.2.1.19 | Integer32 | read-only | SNR -- avg in the 15 minute interval |
| I32 jnxPMIntMinTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.2.1.20 | Integer32 | read-only | TxOutputPower -- min in the 15 minute interval |
| I32 jnxPMIntMaxTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.2.1.21 | Integer32 | read-only | TxOutputPower -- max in the 15 minute interval |
| I32 jnxPMIntAvgTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.2.1.22 | Integer32 | read-only | TxOutputPower -- average in the 15 minute interval |
| I32 jnxPMIntMinRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.2.1.23 | Integer32 | read-only | RxInputPower -- min in the 15 minute interval |
| I32 jnxPMIntMaxRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.2.1.24 | Integer32 | read-only | RxInputPower -- max in the 15 minute interval |
| I32 jnxPMIntAvgRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.2.1.25 | Integer32 | read-only | RxInputPower -- average in the 15 minute interval |
| DAT jnxPMIntTimeStamp | 1.3.6.1.4.1.2636.3.71.1.2.2.1.26 | DateAndTime | read-only | Time stamp PM interval |
| T/F jnxPMIntSuspectedFlag | 1.3.6.1.4.1.2636.3.71.1.2.2.1.27 | TruthValue | read-only | If true, the data in this entry may be unreliable. |
| I32 jnxPMIntSuspectReason | 1.3.6.1.4.1.2636.3.71.1.2.2.1.28 | Integer32 | read-only | If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts |
| I32 jnxPMIntMinTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.2.1.29 | Integer32 | read-only | Transmit Minimum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMIntMaxTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.2.1.30 | Integer32 | read-only | Transmit Maximum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMIntAvgTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.2.1.31 | Integer32 | read-only | Transmit Average LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMIntMinTemperature | 1.3.6.1.4.1.2636.3.71.1.2.2.1.32 | Integer32 | read-only | Minimum Temperature measured at Transceiver port |
| I32 jnxPMIntMaxTemperature | 1.3.6.1.4.1.2636.3.71.1.2.2.1.33 | Integer32 | read-only | Maximum Temperature measure at Transceiver port |
| I32 jnxPMIntAvgTemperature | 1.3.6.1.4.1.2636.3.71.1.2.2.1.34 | Integer32 | read-only | Average Temperature measure at Transceiver port |
| I32 jnxPMIntMinCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.2.1.35 | Integer32 | read-only | Minimum Carrier frequency offset measured at Transceiver port |
| I32 jnxPMIntMaxCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.2.1.36 | Integer32 | read-only | Maximum Carrier frequency offset measured at Transceiver port |
| I32 jnxPMIntAvgCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.2.1.37 | Integer32 | read-only | Average Carrier frequency offset measured at Transceiver port |
| I32 jnxPMIntMinRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.2.1.38 | Integer32 | read-only | Receive Minimum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMIntMaxRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.2.1.39 | Integer32 | read-only | Receive Maximum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMIntAvgRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.2.1.40 | Integer32 | read-only | Receive Average LaserBiasCurrent measured at Transceiver port |
| jnxOpticsPMDayTable | 1.3.6.1.4.1.2636.3.71.1.2.3 | not-accessible | A table of current PM Day entries. | |
| jnxOpticsPMDayEntry | 1.3.6.1.4.1.2636.3.71.1.2.3.1 | not-accessible | A conceptual row that contains information about the PM Day Table | |
| U32 jnxOpticsPMDayIndex | 1.3.6.1.4.1.2636.3.71.1.2.3.1.1 | Unsigned32 | not-accessible | This is 1 - cur day/ 2 - prev day |
| I32 jnxPMDayMinChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.3.1.2 | Integer32 | read-only | Residual Chromatic Dispersion measured at Rx Transceiver port - min in the day |
| I32 jnxPMDayMaxChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.3.1.3 | Integer32 | read-only | Residual Chromatic Dispersion measured at Rx Transceiver port - max in the day |
| I32 jnxPMDayAvgChromaticDispersion | 1.3.6.1.4.1.2636.3.71.1.2.3.1.4 | Integer32 | read-only | Residual Chromatic Dispersion measured at Rx Transceiver port - average in the day |
| I32 jnxPMDayMinDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.3.1.5 | Integer32 | read-only | Differential Group Delay measured at Rx Transceiver port -- min in the day |
| I32 jnxPMDayMaxDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.3.1.6 | Integer32 | read-only | Differential Group Delay measured at Rx Transceiver port -- max in the day |
| I32 jnxPMDayAvgDiffGroupDelay | 1.3.6.1.4.1.2636.3.71.1.2.3.1.7 | Integer32 | read-only | Differential Group Delay measured at Rx Transceiver port -- average in the day |
| I32 jnxPMDayMinPolarState | 1.3.6.1.4.1.2636.3.71.1.2.3.1.8 | Integer32 | read-only | Polarization state -- min in the day |
| I32 jnxPMDayMaxPolarState | 1.3.6.1.4.1.2636.3.71.1.2.3.1.9 | Integer32 | read-only | Polarization state -- max in the day |
| I32 jnxPMDayAvgPolarState | 1.3.6.1.4.1.2636.3.71.1.2.3.1.10 | Integer32 | read-only | Polarization state -- average in the day |
| I32 jnxPMDayMinPolarDependentLoss | 1.3.6.1.4.1.2636.3.71.1.2.3.1.11 | Integer32 | read-only | Polarization Dependent Loss -- min in the day |
| I32 jnxPMDayMaxPolarDependentLoss | 1.3.6.1.4.1.2636.3.71.1.2.3.1.12 | Integer32 | read-only | Polarization Dependent Loss -- max in the day |
| I32 jnxPMDayAvgPolarDependentLoss | 1.3.6.1.4.1.2636.3.71.1.2.3.1.13 | Integer32 | read-only | Polarization Dependent Loss -- average in the day interval |
| I32 jnxPMDayMinQ | 1.3.6.1.4.1.2636.3.71.1.2.3.1.14 | Integer32 | read-only | Q -- min in the day |
| I32 jnxPMDayMaxQ | 1.3.6.1.4.1.2636.3.71.1.2.3.1.15 | Integer32 | read-only | Q -- max in the day |
| I32 jnxPMDayAvgQ | 1.3.6.1.4.1.2636.3.71.1.2.3.1.16 | Integer32 | read-only | Q -- Avg in the day |
| I32 jnxPMDayMinSNR | 1.3.6.1.4.1.2636.3.71.1.2.3.1.17 | Integer32 | read-only | SNR -- min in the day |
| I32 jnxPMDayMaxSNR | 1.3.6.1.4.1.2636.3.71.1.2.3.1.18 | Integer32 | read-only | SNR -- max in the day |
| I32 jnxPMDayAvgSNR | 1.3.6.1.4.1.2636.3.71.1.2.3.1.19 | Integer32 | read-only | SNR -- avg in the day |
| I32 jnxPMDayMinTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.3.1.20 | Integer32 | read-only | TxOutputPower -- min in the day |
| I32 jnxPMDayMaxTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.3.1.21 | Integer32 | read-only | TxOutputPower -- max in the day. |
| I32 jnxPMDayAvgTxOutputPower | 1.3.6.1.4.1.2636.3.71.1.2.3.1.22 | Integer32 | read-only | TxOutputPower -- average in the day. |
| I32 jnxPMDayMinRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.3.1.23 | Integer32 | read-only | RxInputPower -- min in the day. |
| I32 jnxPMDayMaxRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.3.1.24 | Integer32 | read-only | RxInputPower -- max in the day. |
| I32 jnxPMDayAvgRxInputPower | 1.3.6.1.4.1.2636.3.71.1.2.3.1.25 | Integer32 | read-only | RxInputPower -- average in the day. |
| DAT jnxPMDayTimeStamp | 1.3.6.1.4.1.2636.3.71.1.2.3.1.26 | DateAndTime | read-only | Time for the Day. |
| T/F jnxPMDaySuspectedFlag | 1.3.6.1.4.1.2636.3.71.1.2.3.1.27 | TruthValue | read-only | If true, the data in this entry may be unreliable. |
| I32 jnxPMDaySuspectReason | 1.3.6.1.4.1.2636.3.71.1.2.3.1.28 | Integer32 | read-only | If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - partial data 7 - one or more intervals are invaild |
| I32 jnxPMDayMinTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.3.1.29 | Integer32 | read-only | Transmit LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMDayMaxTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.3.1.30 | Integer32 | read-only | Transmit Minimum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMDayAvgTxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.3.1.31 | Integer32 | read-only | Transmit Maximum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMDayMinTemperature | 1.3.6.1.4.1.2636.3.71.1.2.3.1.32 | Integer32 | read-only | Minimum Temperature measured at Transceiver port |
| I32 jnxPMDayMaxTemperature | 1.3.6.1.4.1.2636.3.71.1.2.3.1.33 | Integer32 | read-only | Maximum Temperature measure at Transceiver port |
| I32 jnxPMDayAvgTemperature | 1.3.6.1.4.1.2636.3.71.1.2.3.1.34 | Integer32 | read-only | Average Temperature measure at Transceiver port |
| I32 jnxPMDayMinCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.3.1.35 | Integer32 | read-only | Minimum Carrier frequency offset measured at Transceiver port |
| I32 jnxPMDayMaxCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.3.1.36 | Integer32 | read-only | Maximum Carrier frequency offset measured at Transceiver port |
| I32 jnxPMDayAvgCarFreqOffset | 1.3.6.1.4.1.2636.3.71.1.2.3.1.37 | Integer32 | read-only | Average Carrier frequency offset measured at Transceiver port |
| I32 jnxPMDayMinRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.3.1.38 | Integer32 | read-only | Receive LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMDayMaxRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.3.1.39 | Integer32 | read-only | Receive Minimum LaserBiasCurrent measured at Transceiver port |
| I32 jnxPMDayAvgRxLaserBiasCurrent | 1.3.6.1.4.1.2636.3.71.1.2.3.1.40 | Integer32 | read-only | Receive Maximum LaserBiasCurrent measured at Transceiver port |
| jnxOpticsAlarm | 1.3.6.1.4.1.2636.3.71.1.3 | |||
| jnxOpticsNotificationTable | 1.3.6.1.4.1.2636.3.71.1.3.1 | not-accessible | A table of Notification entries. | |
| jnxOpticsNotificationEntry | 1.3.6.1.4.1.2636.3.71.1.3.1.1 | not-accessible | A conceptual entry in the Notification table. | |
| JNX jnxOpticsNotificationLocation | 1.3.6.1.4.1.2636.3.71.1.3.1.1.1 | JnxOpticsLocation | accessible-for-notify | The object identifies indicates if this entry was for Near end/Far end. |
| JNX jnxOpticsNotificationDirection | 1.3.6.1.4.1.2636.3.71.1.3.1.1.2 | JnxOpticsDirection | accessible-for-notify | The object identifies indicates if this entry was for for the Tx/Rx or both. |
| JNX jnxOpticsLastNotificationId | 1.3.6.1.4.1.2636.3.71.1.3.1.1.3 | JnxOpticsNotificationId | accessible-for-notify | The object identifies the OTN alarm that most recently was set or cleared. |
| JNX jnxOpticsNotificationSeverity | 1.3.6.1.4.1.2636.3.71.1.3.1.1.4 | JnxOpticsSeverity | accessible-for-notify | The object identifies the severity of the last alarm/alert that most recently was set or cleared. |
| DAT jnxOpticsNotificationDate | 1.3.6.1.4.1.2636.3.71.1.3.1.1.5 | DateAndTime | accessible-for-notify | This specifies the date and time when this alarm occurred. |
| jnxOpticsNotificationPrefix | 1.3.6.1.4.1.2636.4.22.0 | |||
| NTF jnxOpticsNotificationSet | 1.3.6.1.4.1.2636.4.22.0.1 | Notification of a recently set optics alarm. | ||
| NTF jnxOpticsNotificationCleared | 1.3.6.1.4.1.2636.4.22.0.2 | Notification of a recently cleared optics alarm. |
RFC description
Manages optical interface properties including configuration, alarms, and performance metrics for Juniper network devices.
Start monitoring Juniper router or switch with pluggable optical/DWDM transceivers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.