All MIBs › INTEL-IPROUTER-MIB
Category: Routing Protocols, Vendor: Intel
Description: Intel IP router MIB providing SNMP objects for routing table management, interface configuration, and router statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is INTEL-IPROUTER-MIB?
INTEL-IPROUTER-MIB is an Intel private-enterprise MIB providing SNMP objects for IP router management on Intel-branded routing platforms, covering routing table management, interface configuration, and router statistics. It falls into the routing/interfaces/performance-counters category, exposing route-table entries, per-interface configuration, and traffic/error statistics for the router. Its monitoring value spans both configuration and operational health: interface configuration objects help confirm correct network setup, while router statistics (packet/error counters) reveal performance issues, and route-table visibility helps detect routing failures or unexpected route changes — collectively giving insight into the router's software-level operational status. As an IP routing MIB it almost certainly overlaps conceptually with and depends on standard IETF MIBs like IP-MIB, IF-MIB, and possibly the standard MIB-II (RFC 1213) for base interface/route objects. It is typically deployed on legacy Intel-manufactured router products in enterprise or branch-office network environments. Network engineers evaluating or troubleshooting this functionality can download the INTEL-IPROUTER-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in INTEL-IPROUTER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Intel IP router
Monitoring Examples
No object names were provided in the source excerpt, so a concrete polling walk cannot be grounded in named identifiers; based on the module description, an administrator would expect to poll a route table for destination/next-hop entries, per-interface configuration objects, and router statistics counters (e.g., packets forwarded, routing errors) to confirm routing is functioning correctly. A spike in routing error counters or an unexpected route-table entry would indicate a routing misconfiguration or network instability.
What Can Be Monitored
- IP routing table entries
- router interface configuration
- router traffic/error statistics
This MIB depends on
Related MIBs
Imported Objects
From INTEL-GEN-MIB
| mib2ext | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| TimeTicks |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| iprouter | 1.3.6.1.4.1.343.6.21 | |||
| conf | 1.3.6.1.4.1.343.6.21.1 | |||
| confIfTable | 1.3.6.1.4.1.343.6.21.1.1 | not-accessible | The table contains configuration information for each IP link. | |
| confIfEntry | 1.3.6.1.4.1.343.6.21.1.1.1 | not-accessible | Configuration information for the IP link. | |
| INT confIfIndex | 1.3.6.1.4.1.343.6.21.1.1.1.1 | INTEGER | read-only | The ifIndex of the IP link. |
| OCT confIfAddrAndMask1 | 1.3.6.1.4.1.343.6.21.1.1.1.2 | OCTET STRING | read-write | The primary IP Address and Mask of the IP link. The format of the octet string is: 4 bytes : IP Address. 4 bytes : Subnet Mask. A string of all zeros is used for unnumbered links. |
| OCT confIfAddrAndMask2 | 1.3.6.1.4.1.343.6.21.1.1.1.3 | OCTET STRING | read-write | The second IP Address and Mask of the IP link. The format of the octet string is: 4 bytes : IP Address. 4 bytes : Subnet Mask. |
| OCT confIfAddrAndMask3 | 1.3.6.1.4.1.343.6.21.1.1.1.4 | OCTET STRING | read-write | The third IP Address and Mask of the IP link. The format of the octet string is: 4 bytes : IP Address. 4 bytes : Subnet Mask. |
| OCT confIfAddrAndMask4 | 1.3.6.1.4.1.343.6.21.1.1.1.5 | OCTET STRING | read-write | The fourth IP Address and Mask of the IP link. The format of the octet string is: 4 bytes : IP Address. 4 bytes : Subnet Mask. |
| INT confIfRouteProto | 1.3.6.1.4.1.343.6.21.1.1.1.6 | INTEGER | read-write | The Routing Protocol used on the link. |
| INT confIfTrigRip | 1.3.6.1.4.1.343.6.21.1.1.1.7 | INTEGER | read-write | Indicates whether Triggered RIP is used on the link. |
| INT confIfRipMetric | 1.3.6.1.4.1.343.6.21.1.1.1.8 | INTEGER | read-write | The RIP metric used on the link. |
| INT confIfRip2AuthType | 1.3.6.1.4.1.343.6.21.1.1.1.9 | INTEGER | read-write | The RIP-2 Authentication type used on the link. |
| OCT confIfRip2AuthKey | 1.3.6.1.4.1.343.6.21.1.1.1.10 | OCTET STRING | read-write | The authentication key used in RIP-2. |
| INT confIfBootpReqForw | 1.3.6.1.4.1.343.6.21.1.1.1.11 | INTEGER | read-write | Indicates whether BOOTP requests are forwarded on the link |
| INT confIfProxyArp | 1.3.6.1.4.1.343.6.21.1.1.1.12 | INTEGER | read-write | Indicates whether Proxy Arp is used on the link. |
| INT confIfFiltering | 1.3.6.1.4.1.343.6.21.1.1.1.13 | INTEGER | read-write | Indicates whether IP filtering is used on the link. |
| INT confIfRxDefAction | 1.3.6.1.4.1.343.6.21.1.1.1.14 | INTEGER | read-write | Indicates whether packets not matching any of the Rx filters on the link must be passed or discarded. |
| INT confIfTxDefAction | 1.3.6.1.4.1.343.6.21.1.1.1.15 | INTEGER | read-write | Indicates whether packets not matching any of the Tx filters on the link must be passed or discarded. |
| INT confIfRxDefLogging | 1.3.6.1.4.1.343.6.21.1.1.1.16 | INTEGER | read-write | Indicates whether packets not matching any of the Rx filters must be logged. |
| INT confIfTxDefLogging | 1.3.6.1.4.1.343.6.21.1.1.1.17 | INTEGER | read-write | Indicates whether packets not matching any of the Tx filters must be logged. |
| OCT confIfCreateObj | 1.3.6.1.4.1.343.6.21.1.1.1.18 | OCTET STRING | read-write | Create a non existing table entry. If the entry already exist, genError is returned. Binary format: 4 bytes : confIfAddr1 4 bytes : confIfMask1 4 bytes : confIfAddr2 4 bytes : confIfMask2 4 bytes : confIfAddr3 4 bytes : confIfMask3 4 bytes : confIfAddr4 4 bytes : confIfMask4 1 byte : confIfRouteProto 1 byte : confIfTrigRip 1 byte : confIfRipMetric 1 byte : confIfRip2AuthType 16 bytes : confIfRip2AuthKey 1 byte : confIfBootpReqForw 1 byte : confIfProxyArp 1 byte : confIfFiltering 1 byte : confIfRxDefAction 1 byte : confIfTxDefAction 1 byte : confIfRxDefLogging 1 byte : confIfTxDefLogging 1 byte : confIfTtlThreshold 30 bytes : confIfTunnelName 4 bytes : confIfLocalIP 4 bytes : confIfRemoteIP 1 byte : confIfMgtAccess 1 byte : confIfRtrDiscovery |
| INT confIfDeleteObj | 1.3.6.1.4.1.343.6.21.1.1.1.19 | INTEGER | read-write | Delete an existing table entry |
| INT confIfMCRouteProto | 1.3.6.1.4.1.343.6.21.1.1.1.20 | INTEGER | read-only | The multicast Routing Protocol used on the link. |
| INT confIfDvmrpMetric | 1.3.6.1.4.1.343.6.21.1.1.1.21 | INTEGER | read-only | The DVMRP metric used on the link. |
| INT confIfTtlThreshold | 1.3.6.1.4.1.343.6.21.1.1.1.22 | INTEGER | read-write | The TTL Threshold used on the link. |
| OCT confIfTunnelName | 1.3.6.1.4.1.343.6.21.1.1.1.23 | OCTET STRING | read-write | The symbolic name of the IP-in-IP tunnel. |
| IP confIfLocalIP | 1.3.6.1.4.1.343.6.21.1.1.1.24 | IpAddress | read-write | The Local IP address of the IP-in-IP tunnel. |
| IP confIfRemoteIP | 1.3.6.1.4.1.343.6.21.1.1.1.25 | IpAddress | read-write | The Remote IP address of the IP-in-IP tunnel. |
| INT confIfMgtAccess | 1.3.6.1.4.1.343.6.21.1.1.1.26 | INTEGER | read-write | Indicates whether management access to the router is allowed via the link. |
| INT confIfRtrDiscovery | 1.3.6.1.4.1.343.6.21.1.1.1.27 | INTEGER | read-write | Indicates whether the router is allowed to send ICMP Router Advertisement messages. |
| INT confIfType | 1.3.6.1.4.1.343.6.21.1.1.1.28 | INTEGER | read-only | Indicates the type of interface used for the link. |
| INT confMgtAddress | 1.3.6.1.4.1.343.6.21.1.1.1.29 | INTEGER | read-only | Enabled if the first address of this interface is the management address. |
| filterTable | 1.3.6.1.4.1.343.6.21.1.2 | not-accessible | The table contains IP filter configuration information. | |
| filterEntry | 1.3.6.1.4.1.343.6.21.1.2.1 | not-accessible | Configuration information for the IP filter. | |
| INT filterIfIndex | 1.3.6.1.4.1.343.6.21.1.2.1.1 | INTEGER | read-only | The ifIndex of the IP link on which the filter is used. |
| INT filterDirIndex | 1.3.6.1.4.1.343.6.21.1.2.1.2 | INTEGER | read-only | Indicates whether the filter is an Rx or Tx filter. |
| INT filterIndex | 1.3.6.1.4.1.343.6.21.1.2.1.3 | INTEGER | read-only | Index in the Rx or Tx filter list for the link. |
| INT filterAction | 1.3.6.1.4.1.343.6.21.1.2.1.4 | INTEGER | read-write | The action to be taken when a packet matches the filter. Disabled filters are ignored. |
| INT filterLogging | 1.3.6.1.4.1.343.6.21.1.2.1.5 | INTEGER | read-write | Indicates whether packets matching the filter must be logged. |
| INT filterProtocol | 1.3.6.1.4.1.343.6.21.1.2.1.6 | INTEGER | read-write | Indicates whether the filter matches all protocols, a user defined protocol or a known protocol. |
| INT filterProtocolValue | 1.3.6.1.4.1.343.6.21.1.2.1.7 | INTEGER | read-write | The protocol field in the IP header of the packet. |
| INT filterTcpFlags | 1.3.6.1.4.1.343.6.21.1.2.1.8 | INTEGER | read-write | Indicates whether the filter matches all TCP packets or only TCP packets with the ACK flag set. When the ACK flag is set, the packet belongs to an established TCP connection. |
| INT filterSrcAddrType | 1.3.6.1.4.1.343.6.21.1.2.1.9 | INTEGER | read-write | Indicates whether the filter matches all source addresses, addresses on a specific network or a specific host address. |
| IP filterSrcAddr | 1.3.6.1.4.1.343.6.21.1.2.1.10 | IpAddress | read-write | Indicates the network or host address which the source address must match. |
| IP filterSrcMask | 1.3.6.1.4.1.343.6.21.1.2.1.11 | IpAddress | read-write | The subnet mask of the network which the source address must match. |
| INT filterSrcPort | 1.3.6.1.4.1.343.6.21.1.2.1.12 | INTEGER | read-write | Indicates whether the filter matches all or a specific UDP/TCP source port. |
| INT filterSrcPortValue | 1.3.6.1.4.1.343.6.21.1.2.1.13 | INTEGER | read-write | The UDP/TCP source port of the filter. |
| INT filterSrcPortOper | 1.3.6.1.4.1.343.6.21.1.2.1.14 | INTEGER | read-write | The source port operator indicates whether UDP/TCP source port values equal to, not equal to, greater than or less than the filter source port match the filter. |
| INT filterDestAddrType | 1.3.6.1.4.1.343.6.21.1.2.1.15 | INTEGER | read-write | Indicates whether the filter matches all destination addresses, addresses on a specific network or a specific host address. |
| IP filterDestAddr | 1.3.6.1.4.1.343.6.21.1.2.1.16 | IpAddress | read-write | Indicates the network or host address which the destination address must match. |
| IP filterDestMask | 1.3.6.1.4.1.343.6.21.1.2.1.17 | IpAddress | read-write | The subnet mask of the network which the destination address must match. |
| INT filterDestPort | 1.3.6.1.4.1.343.6.21.1.2.1.18 | INTEGER | read-write | Indicates whether the filter matches all or a specific UDP/TCP destination port. |
| INT filterDestPortValue | 1.3.6.1.4.1.343.6.21.1.2.1.19 | INTEGER | read-write | The UDP/TCP destination port of the filter. |
| INT filterDestPortOper | 1.3.6.1.4.1.343.6.21.1.2.1.20 | INTEGER | read-write | The destination port operator indicates whether UDP/TCP destination port values equal to, not equal to, greater than or less than the filter destination port match the filter. |
| CTR filterHits | 1.3.6.1.4.1.343.6.21.1.2.1.21 | Counter | read-only | The number of packets matching the filter. |
| natTable | 1.3.6.1.4.1.343.6.21.1.3 | not-accessible | The table contains NAT information. | |
| natEntry | 1.3.6.1.4.1.343.6.21.1.3.1 | not-accessible | Information for the NAT entry. | |
| INT natIfIndex | 1.3.6.1.4.1.343.6.21.1.3.1.1 | INTEGER | read-only | The ifIndex of the IP link on which the NAT entry is used. |
| INT natIndex | 1.3.6.1.4.1.343.6.21.1.3.1.2 | INTEGER | read-only | Internal NAT index. |
| IP natIntAddr | 1.3.6.1.4.1.343.6.21.1.3.1.3 | IpAddress | read-write | The Internal IP Address of the NAT entry. |
| IP natIntMask | 1.3.6.1.4.1.343.6.21.1.3.1.4 | IpAddress | read-write | The Internal Mask of the NAT entry. |
| INT natIntPort | 1.3.6.1.4.1.343.6.21.1.3.1.5 | INTEGER | read-write | The Internal Port of the NAT entry. |
| IP natExtAddr | 1.3.6.1.4.1.343.6.21.1.3.1.6 | IpAddress | read-write | The External IP Address of the NAT entry. |
| IP natExtMask | 1.3.6.1.4.1.343.6.21.1.3.1.7 | IpAddress | read-write | The External Mask of the NAT entry. |
| INT natExtPort | 1.3.6.1.4.1.343.6.21.1.3.1.8 | INTEGER | read-write | The External Port of the NAT entry. |
| INT natType | 1.3.6.1.4.1.343.6.21.1.3.1.9 | INTEGER | read-write | Indicates whether the NAT entry is static or dynamic. |
| INT natTime | 1.3.6.1.4.1.343.6.21.1.3.1.10 | INTEGER | read-only | The time left for dynamic NAT entries. |
| statRoutTable | 1.3.6.1.4.1.343.6.21.1.4 | not-accessible | The table contains static route information. | |
| statRoutEntry | 1.3.6.1.4.1.343.6.21.1.4.1 | not-accessible | Information for the static route entry. | |
| INT statRoutIfIndex | 1.3.6.1.4.1.343.6.21.1.4.1.1 | INTEGER | read-write | The ifIndex of the IP link on which the static route is used. |
| IP statRoutNetwork | 1.3.6.1.4.1.343.6.21.1.4.1.2 | IpAddress | read-write | IP address of network. |
| IP statRoutMask | 1.3.6.1.4.1.343.6.21.1.4.1.3 | IpAddress | read-write | Subnet mask of network |
| IP statRoutNextHop | 1.3.6.1.4.1.343.6.21.1.4.1.4 | IpAddress | read-write | Next hop router (LAN only) |
| INT statRoutMetric | 1.3.6.1.4.1.343.6.21.1.4.1.5 | INTEGER | read-write | Metric to network |
| OCT statRoutCreateObj | 1.3.6.1.4.1.343.6.21.1.4.1.6 | OCTET STRING | read-write | Create a non existing table entry. If the entry already exist, genError is returned. Binary format: 4 bytes : statRoutMask 4 bytes : statRoutNextHop 4 bytes : statRoutMetric |
| INT statRoutDeleteObj | 1.3.6.1.4.1.343.6.21.1.4.1.7 | INTEGER | read-write | Delete an existing table entry |
| INT tosPrefThreshold | 1.3.6.1.4.1.343.6.21.1.5 | INTEGER | read-write | The threshold for Type of Service for the IP router. IP packets have a Precendence value in the Type of Service field. If the value is higher than the threshold the packet will be forwarded with high priority. |
| stat | 1.3.6.1.4.1.343.6.21.2 | |||
| statIfTable | 1.3.6.1.4.1.343.6.21.2.1 | not-accessible | The table contains statistic information for each IP link. | |
| statIfEntry | 1.3.6.1.4.1.343.6.21.2.1.1 | not-accessible | Statistic information for the IP link. | |
| INT statIfIndex | 1.3.6.1.4.1.343.6.21.2.1.1.1 | INTEGER | read-only | The ifIndex of the IP link. |
| INT statIfType | 1.3.6.1.4.1.343.6.21.2.1.1.2 | INTEGER | read-only | The type of the network (LAN or WAN) to which the IP link is connected. |
| INT statIfState | 1.3.6.1.4.1.343.6.21.2.1.1.3 | INTEGER | read-only | The actual state of the IP link. The link layer informs the IP link of link state changes. |
| INT statIfMTU | 1.3.6.1.4.1.343.6.21.2.1.1.4 | INTEGER | read-only | The maximum transmit unit of the IP link. IP packets larger than the MTU will be fragmented. |
| CTR statIfRxDefHits | 1.3.6.1.4.1.343.6.21.2.1.1.5 | Counter | read-only | The number of packets that did not match any of the Rx Filters for the link. |
| CTR statIfTxDefHits | 1.3.6.1.4.1.343.6.21.2.1.1.6 | Counter | read-only | The number of packets that did not match any of the Tx Filters for the link. |
| TIK statIfChange | 1.3.6.1.4.1.343.6.21.2.2 | TimeTicks | read-only | The value of sysUpTime at the time any IP link changed state. |
| arp | 1.3.6.1.4.1.343.6.21.3 | |||
| arpIfTable | 1.3.6.1.4.1.343.6.21.3.1 | not-accessible | The table contains ARP information for each IP link. | |
| arpIfEntry | 1.3.6.1.4.1.343.6.21.3.1.1 | not-accessible | ARP information for the IP link. | |
| INT arpIfIndex | 1.3.6.1.4.1.343.6.21.3.1.1.1 | INTEGER | read-only | The ifIndex of the IP link. |
| CTR arpIfInReq | 1.3.6.1.4.1.343.6.21.3.1.1.2 | Counter | read-only | The number of ARP requests received on the link. |
| CTR arpIfOutRep | 1.3.6.1.4.1.343.6.21.3.1.1.3 | Counter | read-only | The number of ARP replies sent on the link. |
| CTR arpIfOutReq | 1.3.6.1.4.1.343.6.21.3.1.1.4 | Counter | read-only | The number of ARP requests sent on the link. |
| CTR arpIfInRep | 1.3.6.1.4.1.343.6.21.3.1.1.5 | Counter | read-only | The number of ARP replies received on the link. |
| CTR arpIfInHdrErrors | 1.3.6.1.4.1.343.6.21.3.1.1.6 | Counter | read-only | The number of ARP packets received on the link which were discarded because of ARP header errors. |
| CTR arpInReq | 1.3.6.1.4.1.343.6.21.3.2 | Counter | read-only | The total number of ARP requests received. |
| CTR arpOutRep | 1.3.6.1.4.1.343.6.21.3.3 | Counter | read-only | The total number of ARP replies sent. |
| CTR arpOutReq | 1.3.6.1.4.1.343.6.21.3.4 | Counter | read-only | The total number of ARP requests sent. |
| CTR arpInRep | 1.3.6.1.4.1.343.6.21.3.5 | Counter | read-only | The total number of ARP replies received. |
| CTR arpInHdrErrors | 1.3.6.1.4.1.343.6.21.3.6 | Counter | read-only | The total number of received ARP packets which were discarded because of ARP header errors. |
| ip | 1.3.6.1.4.1.343.6.21.4 | |||
| ipIfTable | 1.3.6.1.4.1.343.6.21.4.1 | not-accessible | The table contains statistic information for each IP link. | |
| ipIfEntry | 1.3.6.1.4.1.343.6.21.4.1.1 | not-accessible | IP information for the IP link. | |
| INT ipIfIndex | 1.3.6.1.4.1.343.6.21.4.1.1.1 | INTEGER | read-only | The ifIndex of the IP link. |
| CTR ipIfInReceives | 1.3.6.1.4.1.343.6.21.4.1.1.2 | Counter | read-only | The number of IP packets received on the link. |
| CTR ipIfInHdrErrors | 1.3.6.1.4.1.343.6.21.4.1.1.3 | Counter | read-only | The number of IP packets received on the link which were discarded because of IP header errors. |
| CTR ipIfInAddrErrors | 1.3.6.1.4.1.343.6.21.4.1.1.4 | Counter | read-only | The number of IP packets received on the link which were discarded because of IP source or destination address errors. |
| CTR ipIfInDiscards | 1.3.6.1.4.1.343.6.21.4.1.1.5 | Counter | read-only | The number of IP packets received on the link which were discarded because of lack of buffer space. |
| CTR ipIfForwDatagrams | 1.3.6.1.4.1.343.6.21.4.1.1.6 | Counter | read-only | The number of IP packets forwarded on the link. |
| CTR ipIfOutRequests | 1.3.6.1.4.1.343.6.21.4.1.1.7 | Counter | read-only | The number of IP packets sent by the router itself. |
| CTR ipIfOutDiscards | 1.3.6.1.4.1.343.6.21.4.1.1.8 | Counter | read-only | The number of IP packets which should have been sent on the link, but were discarded because of lack of buffer space or failed ARP requests. |
| icmp | 1.3.6.1.4.1.343.6.21.5 | |||
| icmpIfTable | 1.3.6.1.4.1.343.6.21.5.1 | not-accessible | The table contains ICMP information for each IP link. | |
| icmpIfEntry | 1.3.6.1.4.1.343.6.21.5.1.1 | not-accessible | ICMP information for the IP link. | |
| INT icmpIfIndex | 1.3.6.1.4.1.343.6.21.5.1.1.1 | INTEGER | read-only | The ifIndex of the IP link. |
| CTR icmpIfInMsgs | 1.3.6.1.4.1.343.6.21.5.1.1.2 | Counter | read-only | The number of ICMP messages to the router received on the link. |
| CTR icmpIfInErrors | 1.3.6.1.4.1.343.6.21.5.1.1.3 | Counter | read-only | The number of ICMP messages to the router received on the link which were discarded because of ICMP header errors. |
| CTR icmpIfInEchos | 1.3.6.1.4.1.343.6.21.5.1.1.4 | Counter | read-only | The number of ICMP echo requests received on the link. |
| CTR icmpIfInEchoReps | 1.3.6.1.4.1.343.6.21.5.1.1.5 | Counter | read-only | The number of ICMP echo replies received on the link. |
| CTR icmpIfOutMsgs | 1.3.6.1.4.1.343.6.21.5.1.1.6 | Counter | read-only | The number of ICMP messages sent on the link. |
| CTR icmpIfOutEchos | 1.3.6.1.4.1.343.6.21.5.1.1.7 | Counter | read-only | The number of ICMP echo requests sent on the link. |
| CTR icmpIfOutEchoReps | 1.3.6.1.4.1.343.6.21.5.1.1.8 | Counter | read-only | The number of ICMP echo replies sent on the link. |
| CTR icmpInRouterAdvs | 1.3.6.1.4.1.343.6.21.5.2 | Counter | read-only | The total number of received ICMP Router Advertisements. |
| CTR icmpInRouterSols | 1.3.6.1.4.1.343.6.21.5.3 | Counter | read-only | The total number of received ICMP Router Solicitations. |
| CTR icmpOutRouterAdvs | 1.3.6.1.4.1.343.6.21.5.4 | Counter | read-only | The total number of sent ICMP Router Advertisements. |
| CTR icmpOutRouterSols | 1.3.6.1.4.1.343.6.21.5.5 | Counter | read-only | The total number of sent ICMP Router Solicitations. |
| rip | 1.3.6.1.4.1.343.6.21.6 | |||
| ripIfTable | 1.3.6.1.4.1.343.6.21.6.1 | not-accessible | The table contains RIP information for each IP link. | |
| ripIfEntry | 1.3.6.1.4.1.343.6.21.6.1.1 | not-accessible | RIP information for the IP link. | |
| INT ripIfIndex | 1.3.6.1.4.1.343.6.21.6.1.1.1 | INTEGER | read-only | The ifIndex of the IP link. |
| CTR ripIfInReceives | 1.3.6.1.4.1.343.6.21.6.1.1.2 | Counter | read-only | The number of RIP packets received on the link. |
| CTR ripIfInHdrErrors | 1.3.6.1.4.1.343.6.21.6.1.1.3 | Counter | read-only | The number of RIP packets received on the link which were discarded because of RIP header errors. |
| CTR ripIfInBadSrcAddrs | 1.3.6.1.4.1.343.6.21.6.1.1.4 | Counter | read-only | The number of RIP packets received on the link which were discarded because of source address errors. This may indicate an IP address configuration error on the link or the link of the router from which the RIP packet was received. The error may also occur if the link is connected to a physical network with multiple logical IP networks. In the latter case a source address error is not an indication of an IP address configuration error. |
| CTR ripIfInBadVers | 1.3.6.1.4.1.343.6.21.6.1.1.5 | Counter | read-only | The number of RIP packets received on the link which were discarded because of RIP version errors. This indicates a RIP configuration error on the link or the link of the router from which the RIP packet was received. The error occurs when receiving a RIP packet with a version different from the version configured on the link. The error also occurs if a RIP packet is received and the link is configured not to use RIP. |
| CTR ripIfInAuthFails | 1.3.6.1.4.1.343.6.21.6.1.1.6 | Counter | read-only | The number of RIP packets received on the link which were discarded because of RIP-2 authentication failures. |
| CTR ripIfInUnknComs | 1.3.6.1.4.1.343.6.21.6.1.1.7 | Counter | read-only | The number of RIP packets received on the link which were discarded because of an unknown command type. This may indicate that the link is not configured to use Triggered RIP and the remote router is using Triggered RIP. |
| CTR ripIfOutSent | 1.3.6.1.4.1.343.6.21.6.1.1.8 | Counter | read-only | The number of RIP packets sent on the link. |
| CTR ripIfOutDiscards | 1.3.6.1.4.1.343.6.21.6.1.1.9 | Counter | read-only | The number of RIP packets discarded because of lack of buffer space. |
| CTR ripInReceives | 1.3.6.1.4.1.343.6.21.6.2 | Counter | read-only | The total number of received RIP packets. |
| CTR ripInHdrErrors | 1.3.6.1.4.1.343.6.21.6.3 | Counter | read-only | The total number of received RIP packets discarded because of RIP header errors. |
| CTR ripInBadSrcAddrs | 1.3.6.1.4.1.343.6.21.6.4 | Counter | read-only | The total number of received RIP packets discarded because of source address errors. |
| CTR ripInBadVers | 1.3.6.1.4.1.343.6.21.6.5 | Counter | read-only | The total number of received RIP packets discarded because of RIP version errors. |
| CTR ripInAuthFails | 1.3.6.1.4.1.343.6.21.6.6 | Counter | read-only | The total number of RIP-2 authentication failures. |
| CTR ripInUnknComs | 1.3.6.1.4.1.343.6.21.6.7 | Counter | read-only | The total number of received RIP packets discarded because of an unknown command type. |
| CTR ripOutSent | 1.3.6.1.4.1.343.6.21.6.8 | Counter | read-only | The total number of RIP packets sent by the router. |
| CTR ripOutDiscards | 1.3.6.1.4.1.343.6.21.6.9 | Counter | read-only | The total number of RIP packets discarded because of lack of buffer space. |
| bootp | 1.3.6.1.4.1.343.6.21.7 | |||
| bootpIfTable | 1.3.6.1.4.1.343.6.21.7.1 | not-accessible | The table contains BOOTP information for each IP link. | |
| bootpIfEntry | 1.3.6.1.4.1.343.6.21.7.1.1 | not-accessible | BOOTP information for the IP link. | |
| INT bootpIfIndex | 1.3.6.1.4.1.343.6.21.7.1.1.1 | INTEGER | read-only | The ifIndex of the IP link. |
| CTR bootpIfInRequests | 1.3.6.1.4.1.343.6.21.7.1.1.2 | Counter | read-only | The number of BOOTP requests received on the link. |
| CTR bootpIfInReplies | 1.3.6.1.4.1.343.6.21.7.1.1.3 | Counter | read-only | The number of BOOTP replies received on the link. |
| CTR bootpIfInErrors | 1.3.6.1.4.1.343.6.21.7.1.1.4 | Counter | read-only | The number of BOOTP packets received on the link which were discarded because of header errors. |
| CTR bootpIfInDiscards | 1.3.6.1.4.1.343.6.21.7.1.1.5 | Counter | read-only | The number of BOOTP requests received on the link which were discarded. This is done in the following situations: - The maximum value of the BOOTP hop count is exceeded. - More than 3 BOOTP packets are received per second. - The router does not have a route back to the assisting router using the receving link. |
| CTR bootpIfOutRequests | 1.3.6.1.4.1.343.6.21.7.1.1.6 | Counter | read-only | The number of BOOTP requests sent on the link. |
| CTR bootpIfOutReplies | 1.3.6.1.4.1.343.6.21.7.1.1.7 | Counter | read-only | The number of BOOTP replies sent on the link. |
| CTR bootpIfOutDiscards | 1.3.6.1.4.1.343.6.21.7.1.1.8 | Counter | read-only | The number of BOOTP requests discarded because of lack of buffer space. |
| CTR bootpInRequests | 1.3.6.1.4.1.343.6.21.7.2 | Counter | read-only | The total number of received BOOTP requests. |
| CTR bootpInReplies | 1.3.6.1.4.1.343.6.21.7.3 | Counter | read-only | The total number of received BOOTP replies. |
| CTR bootpInErrors | 1.3.6.1.4.1.343.6.21.7.4 | Counter | read-only | The total number of received BOOTP packets discarded because of header errors. |
| CTR bootpInDiscards | 1.3.6.1.4.1.343.6.21.7.5 | Counter | read-only | The total number of received BOOTP requests discarded. This is done in the following situations: - The maximum value of the BOOTP hop count is exceeded. - More than 3 BOOTP packets are received per second. - The router does not have a route back to the assisting router using the receiving link. |
| CTR bootpOutRequests | 1.3.6.1.4.1.343.6.21.7.6 | Counter | read-only | The total number of BOOTP requests sent by the router. |
| CTR bootpOutReplies | 1.3.6.1.4.1.343.6.21.7.7 | Counter | read-only | The total number of BOOTP replies sent to BOOTP clients. |
| CTR bootpOutDiscards | 1.3.6.1.4.1.343.6.21.7.8 | Counter | read-only | The total number of BOOTP requests discarded because of lack of buffer space. |
| INT bootpMaxHops | 1.3.6.1.4.1.343.6.21.7.9 | INTEGER | read-write | The maximum allowed value of the hop count in received BOOTP requests. |
| octetcounters | 1.3.6.1.4.1.343.6.21.8 | |||
| octetIfTable | 1.3.6.1.4.1.343.6.21.8.1 | not-accessible | The table contains octet counters for each IP link. | |
| octetIfEntry | 1.3.6.1.4.1.343.6.21.8.1.1 | not-accessible | Octet counter information for the IP link. | |
| INT octetIfIndex | 1.3.6.1.4.1.343.6.21.8.1.1.1 | INTEGER | read-only | The ifIndex of the IP link. |
| CTR octetIfInTotal | 1.3.6.1.4.1.343.6.21.8.1.1.2 | Counter | read-only | The total number of octets received on the IP link. |
| CTR octetIfOutTotal | 1.3.6.1.4.1.343.6.21.8.1.1.3 | Counter | read-only | The total number of octets sent on the IP link. |
| CTR octetIfInOther | 1.3.6.1.4.1.343.6.21.8.1.1.4 | Counter | read-only | The number of octets received on the IP link which were not classified as a specific protocol. |
| CTR octetIfOutOther | 1.3.6.1.4.1.343.6.21.8.1.1.5 | Counter | read-only | The number of octets sent on the IP link which were not classified as a specific protocol. |
| CTR octetIfInFtp | 1.3.6.1.4.1.343.6.21.8.1.1.6 | Counter | read-only | The number of FTP octets received on the IP link. |
| CTR octetIfOutFtp | 1.3.6.1.4.1.343.6.21.8.1.1.7 | Counter | read-only | The number of FTP octets sent on the IP link. |
| CTR octetIfInTelnet | 1.3.6.1.4.1.343.6.21.8.1.1.8 | Counter | read-only | The number of Telnet octets received on the IP link. |
| CTR octetIfOutTelnet | 1.3.6.1.4.1.343.6.21.8.1.1.9 | Counter | read-only | The number of Telnet octets sent on the IP link. |
| CTR octetIfInSmtp | 1.3.6.1.4.1.343.6.21.8.1.1.10 | Counter | read-only | The number of SMTP octets received on the IP link. |
| CTR octetIfOutSmtp | 1.3.6.1.4.1.343.6.21.8.1.1.11 | Counter | read-only | The number of SMTP octets sent on the IP link. |
| CTR octetIfInDns | 1.3.6.1.4.1.343.6.21.8.1.1.12 | Counter | read-only | The number of DNS octets received on the IP link. |
| CTR octetIfOutDns | 1.3.6.1.4.1.343.6.21.8.1.1.13 | Counter | read-only | The number of DNS octets sent on the IP link. |
| CTR octetIfInBootp | 1.3.6.1.4.1.343.6.21.8.1.1.14 | Counter | read-only | The number of BOOTP octets received on the IP link. |
| CTR octetIfOutBootp | 1.3.6.1.4.1.343.6.21.8.1.1.15 | Counter | read-only | The number of BOOTP octets sent on the IP link. |
| CTR octetIfInHttp | 1.3.6.1.4.1.343.6.21.8.1.1.16 | Counter | read-only | The number of HTTP octets received on the IP link. |
| CTR octetIfOutHttp | 1.3.6.1.4.1.343.6.21.8.1.1.17 | Counter | read-only | The number of HTTP octets sent on the IP link. |
| CTR octetIfInSnmp | 1.3.6.1.4.1.343.6.21.8.1.1.18 | Counter | read-only | The number of SNMP octets received on the IP link. |
| CTR octetIfOutSnmp | 1.3.6.1.4.1.343.6.21.8.1.1.19 | Counter | read-only | The number of SNMP octets sent on the IP link. |
| CTR octetIfInRip | 1.3.6.1.4.1.343.6.21.8.1.1.20 | Counter | read-only | The number of RIP octets received on the IP link. |
| CTR octetIfOutRip | 1.3.6.1.4.1.343.6.21.8.1.1.21 | Counter | read-only | The number of RIP octets sent on the IP link. |
| CTR octetIfInTunnel | 1.3.6.1.4.1.343.6.21.8.1.1.22 | Counter | read-only | The number of Tunnel octets received on the IP link. |
| CTR octetIfOutTunnel | 1.3.6.1.4.1.343.6.21.8.1.1.23 | Counter | read-only | The number of Tunnel octets sent on the IP link. |
RFC description
Intel IP router MIB providing SNMP objects for routing table management, interface configuration, and router statistics; vendor-private.
Start monitoring Intel IP router (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.