| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ieee8021PbbTeMib | 1.3.111.2.802.1.1.10 | | | Copyright (C) IEEE (2014). All Rights Reserved
This version of this MIB module is part of IEEE 802.1Q;
See the standard itself for full legal notices.
Unless otherwise indicated, the references in this MIB
module are to IEEE Std 802.1Q-2014 |
| ieee8021PbbTeNotifications | 1.3.111.2.802.1.1.10.0 | | | |
| NTF ieee8021PbbTeProtectionGroupAdminFailure | 1.3.111.2.802.1.1.10.0.1 | | | A protection group generates this notification whenever
an adminisistrative command cannot be executed by the
protection state machine. For example, a requested
manual switch cannot be performed because of a signal
failure condition.
The management entity receiving the notification can
identify the system from the network source address of
the notification and can identify the protection group
by the indices of the OID
of the ieee8021PbbTeProtectionGroupConfigState variable in the
notification:
ieee8021BridgeBaseComponentId - Identifies the
component on the Bridge where the protection group
is configured.
ieee8021PbbTeProtectionGroupListGroupId - The id
of the protection group. |
| ieee8021PbbTeObjects | 1.3.111.2.802.1.1.10.1 | | | |
| ieee8021PbbTeProtectionGroupListTable | 1.3.111.2.802.1.1.10.1.1 | | not-accessible | The PBB-TE Protection group list table. Each entry in this table
corresponds to a configured PBB-TE Protection Group configured on
the B-Component of an IB-BEB. |
| ieee8021PbbTeProtectionGroupListEntry | 1.3.111.2.802.1.1.10.1.1.1 | | not-accessible | The PBB-TE protection group list table entry.
Note that the component ID must refer to an B component |
| IEE ieee8021PbbTeProtectionGroupListGroupId | 1.3.111.2.802.1.1.10.1.1.1.1 | IEEE8021PbbTeProtectionGroupId | not-accessible | The unique identifier for the protection group. |
| U32 ieee8021PbbTeProtectionGroupListMD | 1.3.111.2.802.1.1.10.1.1.1.2 | Unsigned32 | read-create | This refers to the Maintenance Domain that qualifies the
WorkingMA and ProtectionMA columns of this table. The MD
index in this column must hold a value that matches the
in the dot1agCfmStackMdIndex in the dot1agCfmStackTable
for the corresponding WorkingMA and ProtectionMA columns
of this table. This correspondence must hold for the RowStatus
of this row to be set to Active. Furthermore, this column may
not be modified while the RowStatus for this row is Active |
| U32 ieee8021PbbTeProtectionGroupListWorkingMA | 1.3.111.2.802.1.1.10.1.1.1.3 | Unsigned32 | read-create | This refers to the Maintenance Association that refers
to the PBB-TE MA that corresponds to the group's working
entity. The MA index in this column must hold a value
that is the value of dot1agCfmStackMaIndex column for
some entry in the dot1agCfmStackTable before the RowStatus
for this row can be set to Active. Furthermore, this column
may not be modified when the RowStatus for this row is Active. |
| U32 ieee8021PbbTeProtectionGroupListProtectionMA | 1.3.111.2.802.1.1.10.1.1.1.4 | Unsigned32 | read-create | This refers to the Maintenance Association that refers
to the PBB-TE MA that corresponds to the group's protection
entity. The MA index in this column must hold a value
that is the value of dot1agCfmStackMaIndex column for
some entry in the dot1agCfmStackTable before the RowStatus
for this row can be set to Active. Furthermore, this column
may not be modified when the RowStatus for this row is Active. |
| STO ieee8021PbbTeProtectionGroupListStorageType | 1.3.111.2.802.1.1.10.1.1.1.5 | StorageType | read-create | This object indicates the persistence of this entry. All read-create
columns must be writable if this column is set to permanent. |
| ROW ieee8021PbbTeProtectionGroupListRowStatus | 1.3.111.2.802.1.1.10.1.1.1.6 | RowStatus | read-create | The status of this row.
The writable columns in a row cannot be changed if the row is
active. The PbbTeProtectionGroupListWorkingMA, and
PbbTeProtectionGroupListProtectionMA columns must be specified
before the row can be activated. |
| ieee8021PbbTeMASharedGroupTable | 1.3.111.2.802.1.1.10.1.2 | | not-accessible | This table contains references to all protection groups that
share a working or protection entity with a given protection
group. |
| ieee8021PbbTeMASharedGroupEntry | 1.3.111.2.802.1.1.10.1.2.1 | | not-accessible | The ieee801PbbTeMASharedGroupEntry table. The table is
indexed by protection group and by a simple integer. The
table lists all protection groups that load share with that
group. |
| U32 ieee8021PbbTeMASharedGroupSubIndex | 1.3.111.2.802.1.1.10.1.2.1.1 | Unsigned32 | not-accessible | A simple integer to distinguish the members of the set
of MAs that comprise the set of load sharing MAs for the
specified protection group. |
| IEE ieee8021PbbTeMASharedGroupId | 1.3.111.2.802.1.1.10.1.2.1.2 | IEEE8021PbbTeProtectionGroupId | read-only | This column holds the group id of a protection group that shares
a working or protection group with the group whose index is the
first index of this row. |
| ieee8021PbbTeTesiTable | 1.3.111.2.802.1.1.10.1.3 | | not-accessible | The PBB-TE TESI table contains information for each
TE Service Instance known to a system. |
| ieee8021PbbTeTesiEntry | 1.3.111.2.802.1.1.10.1.3.1 | | not-accessible | The PBB-TE TESI entry. Each entry maps a TESI to
a component and CBP. |
| IEE ieee8021PbbTeTesiId | 1.3.111.2.802.1.1.10.1.3.1.1 | IEEE8021PbbTeTSidId | not-accessible | This is the unique identifier for a PBB-TE TE-SID. |
| OID ieee8021PbbTeTesiComponent | 1.3.111.2.802.1.1.10.1.3.1.2 | IEEE8021PbbComponentIdentifier | read-create | This is the component upon which the Bridge Port of the
TESI is located. |
| IEE ieee8021PbbTeTesiBridgePort | 1.3.111.2.802.1.1.10.1.3.1.3 | IEEE8021BridgePortNumber | read-create | This is the Bridge Port of the TESI. |
| STO ieee8021PbbTeTesiStorageType | 1.3.111.2.802.1.1.10.1.3.1.4 | StorageType | read-create | This object indicates the persistence of this entry. All read-crate
columns must be writable for rows whose StorageType is permanaent. |
| ROW ieee8021PbbTeTesiRowStatus | 1.3.111.2.802.1.1.10.1.3.1.5 | RowStatus | read-create | This column holds the status for this row.
When the status is active, no columns of this table may be
modified. All columns must have a valid value before the row
can be activated. |
| ieee8021PbbTeTeSiEspTable | 1.3.111.2.802.1.1.10.1.4 | | not-accessible | The PBB-TE TE-SID table contains information for each TE
service instance known to a system. |
| ieee8021PbbTeTeSiEspEntry | 1.3.111.2.802.1.1.10.1.4.1 | | not-accessible | The PBB-TE TE-SID entry. Each entry refers to a
TE Service Instance by identifier and contains information about
one of the ESPs that comprise this TE Service Instance. |
| U32 ieee8021PbbTeTeSiEspEspIndex | 1.3.111.2.802.1.1.10.1.4.1.1 | Unsigned32 | not-accessible | This is an identifier, of local signifigance to a particular
PBB-TE TE-SID which is used to index all of the ESPs associated
with the TE-SID. |
| IEE ieee8021PbbTeTeSiEspEsp | 1.3.111.2.802.1.1.10.1.4.1.2 | IEEE8021PbbTeEsp | read-create | This column holds the ESP identifier for one of the Ethernet
Switched Paths that define the TE service instance. |
| STO ieee8021PbbTeTeSiEspStorageType | 1.3.111.2.802.1.1.10.1.4.1.3 | StorageType | read-create | This object indicates the persistence of this entry. All read-create
columns must be writable for permanent rows. |
| ROW ieee8021PbbTeTeSiEspRowStatus | 1.3.111.2.802.1.1.10.1.4.1.4 | RowStatus | read-create | This column holds the status for this row.
When the status is active, no columns of this table may be
modified. All columns must have a valid value before the row
can be activated. |
| ieee8021PbbTeProtectionGroupConfigTable | 1.3.111.2.802.1.1.10.1.5 | | not-accessible | The PBB-TE Protection group config table contains
configuration and status information for each configuration
group configured in the system. Entries in this table are
created implicitly by the creation of entries in the
ieee8021PbbTeProtectionGroupListTable table. |
| ieee8021PbbTeProtectionGroupConfigEntry | 1.3.111.2.802.1.1.10.1.5.1 | | not-accessible | The protection group confguration table entry. Rows are
created in this table implicitly when a row is added to the
ieee8021PbbTeProtectionGroupListTable. |
| INT ieee8021PbbTeProtectionGroupConfigState | 1.3.111.2.802.1.1.10.1.5.1.1 | INTEGER | read-only | This column indicates the current state of the protection
switching state machine for a protection group. |
| IEE ieee8021PbbTeProtectionGroupConfigCommandStatus | 1.3.111.2.802.1.1.10.1.5.1.2 | IEEE8021PbbTeProtectionGroupConfigAdmin | read-only | This column indicates the status of administrative commands
within the protection group. It reflects the current
operational administrative command being acted upon by the
protection group. |
| IEE ieee8021PbbTeProtectionGroupConfigCommandLast | 1.3.111.2.802.1.1.10.1.5.1.3 | IEEE8021PbbTeProtectionGroupConfigAdmin | read-only | This column indicates the last attempted administrative
command applied to the protection group. It is changed
whenever a write is made to the CommandAdmin column of
this table and is a record of the last attempted
administrative operation. |
| IEE ieee8021PbbTeProtectionGroupConfigCommandAdmin | 1.3.111.2.802.1.1.10.1.5.1.4 | IEEE8021PbbTeProtectionGroupConfigAdmin | read-create | This column is used by the operator to request that the
protection group state machine perform some administrative
operation. The operator requests a command by writing the
command value to this column. The state machine indicates the
command that it is performing by setting the value of the
CommandStatus column of this table. This column always reads
back as clear(1). |
| IEE ieee8021PbbTeProtectionGroupConfigActiveRequests | 1.3.111.2.802.1.1.10.1.5.1.5 | IEEE8021PbbTeProtectionGroupActiveRequests | read-only | This column shows the status of active requests within
the TE protection group. |
| U32 ieee8021PbbTeProtectionGroupConfigWTR | 1.3.111.2.802.1.1.10.1.5.1.6 | Unsigned32 | read-create | This column is used to configure the wait-to-restore timer
for the protection group operation. The timer may be
configured in steps of 1 minute between 5 and 12 minutes, the
default being 5. Additionally, the value 0 is used to
indicate that the protection group is to operate
non-revertively. |
| U32 ieee8021PbbTeProtectionGroupConfigHoldOff | 1.3.111.2.802.1.1.10.1.5.1.7 | Unsigned32 | read-create | This column is used to configure the hold off
timer. The purpose is to allow a service layer protection
mechanism to have a chance to fix athe problem before
switching at the client layer, or to allow an upstream
protected domain to switch before a downsream domain. The
hold off timer has a period of from 0 to 10 seconds, the
default being 0, with a 100ms granularity. |
| T/F ieee8021PbbTeProtectionGroupConfigNotifyEnable | 1.3.111.2.802.1.1.10.1.5.1.8 | TruthValue | read-create | This column is used to enable or disable transmission
of ieee8021PbbTeProtectionGroupAdminFailure
notifications. These notifications are generated
whenever an administrative command cannot be performed
by the protection group. |
| STO ieee8021PbbTeProtectionGroupConfigStorageType | 1.3.111.2.802.1.1.10.1.5.1.9 | StorageType | read-create | This object indicates the persistence of this entry. For
permanent objects the
ieee8021PbbTeProtectionGroupConfigCommandAdmin column
must be writable. |
| ieee8021PbbTeProtectionGroupISidTable | 1.3.111.2.802.1.1.10.1.6 | | not-accessible | This table contains entries for each I-SID that is
transported over TE-SIDs that belong to protection groups.
Each I-SID maps to a single protection group. |
| ieee8021PbbTeProtectionGroupISidEntry | 1.3.111.2.802.1.1.10.1.6.1 | | not-accessible | The ieee8021PbbTeProtectionGroupISidTable entry. |
| OID ieee8021PbbTeProtectionGroupISidIndex | 1.3.111.2.802.1.1.10.1.6.1.1 | IEEE8021PbbServiceIdentifier | not-accessible | This is the I-Sid that is to be mapped to a protection
group. |
| OID ieee8021PbbTeProtectionGroupISidComponentId | 1.3.111.2.802.1.1.10.1.6.1.2 | IEEE8021PbbComponentIdentifier | read-create | This column qualifies the GroupId column to a particular
component. |
| IEE ieee8021PbbTeProtectionGroupISidGroupId | 1.3.111.2.802.1.1.10.1.6.1.3 | IEEE8021PbbTeProtectionGroupId | read-create | This column contains the Id of the protection group used
to transport the data belonging to the service identified
by the I-SID value specified in the ISidIndex column of this
table. |
| STO ieee8021PbbTeProtectionGroupISidStorageType | 1.3.111.2.802.1.1.10.1.6.1.4 | StorageType | read-create | This object indicates the persistence of this entry. |
| ROW ieee8021PbbTeProtectionGroupISidRowStatus | 1.3.111.2.802.1.1.10.1.6.1.5 | RowStatus | read-create | This column contains the status for this row. Once active
none of the columns in the row may be modified. All columns
must be specified when creating the row. |
| ieee8021PbbTeBridgeStaticForwardAnyUnicastTable | 1.3.111.2.802.1.1.10.1.7 | | not-accessible | A table containing forwarding information for each vlan
specifying the set of ports to which forwarding of unicast
addressed frames for which no more specific forwarding information
applies. This is configured statically by management. |
| ieee8021PbbTeBridgeStaticForwardAnyUnicastEntry | 1.3.111.2.802.1.1.10.1.7.1 | | not-accessible | Forwarding information for a VLAN, specifying the
set of ports to which forwarding of unicast addressed
frames for which no more specific forwarding information
applies.
The EgressPorts and ForbiddenPorts PortList objects, together,
implement the PortMap control element listed in 802.1Q 8.8.1.c. |
| IEE ieee8021PbbTeBridgeStaticForwardAnyUnicastVlanIndex | 1.3.111.2.802.1.1.10.1.7.1.1 | IEEE8021VlanIndexOrWildcard | not-accessible | The VLAN-ID or other identifier refering to the VLAN to
which this static filtering entry applies. |
| POR ieee8021PbbTeBridgeStaticForwardAnyUnicastEgressPorts | 1.3.111.2.802.1.1.10.1.7.1.2 | PortList | read-create | The complete set of ports to which a unicast addressed frame
is to be forwarded. This value is persistent and will be restored
upon system reboot. A port may not be added to this set if it
is already a member of
ieee8021PbbTeBridgeStaticForwardAnyUnicastForbiddenPorts. The default
value is a string of zeros of appropriate length.
The value of this object MUST be retained across
reinitialization of the management system. |
| POR ieee8021PbbTeBridgeStaticForwardAnyUnicastForbiddenPorts | 1.3.111.2.802.1.1.10.1.7.1.3 | PortList | read-create | The complete set of ports to which a unicast addressed frame
is to be filtered. This value is persistent and will be restored
upon system reboot. A port may not be added to this set if it
is already a member of
ieee8021PbbTeBridgeStaticForwardAnyUnicastEgress. The default
value is a string of zeros of appropriate length.
The value of this object MUST be retained across
reinitialization of the management system. |
| STO ieee8021PbbTeBridgeStaticForwardAnyUnicastStorageType | 1.3.111.2.802.1.1.10.1.7.1.4 | StorageType | read-create | The storage type for this row. All read-create columns must be
writable for permanent entries. |
| ROW ieee8021PbbTeBridgeStaticForwardAnyUnicastRowStatus | 1.3.111.2.802.1.1.10.1.7.1.5 | RowStatus | read-create | This column contains the status for this row. |
| ieee8021PbbTeConformance | 1.3.111.2.802.1.1.10.2 | | | |
| ieee8021PbbTeCompliances | 1.3.111.2.802.1.1.10.2.1 | | | |
| ieee8021PbbTeCompliance | 1.3.111.2.802.1.1.10.2.1.1 | | | The compliance statement for support of the PBB-TE MIB module. |
| ieee8021PbbTeGroups | 1.3.111.2.802.1.1.10.2.2 | | | |
| ieee8021PbbTeGroupListGroup | 1.3.111.2.802.1.1.10.2.2.1 | | | Objects for the GroupList group. |
| ieee8021PbbTeMASharedGroup | 1.3.111.2.802.1.1.10.2.2.2 | | | Objects for the MA Load Sharing Table Group. |
| ieee8021PbbTeTesiGroup | 1.3.111.2.802.1.1.10.2.2.3 | | | Objects for the TE SI group |
| ieee8021PbbTeSiEspGroup | 1.3.111.2.802.1.1.10.2.2.4 | | | Objects for the TESI ESP group. |
| ieee8021PbbTeProtectionConfigManGroup | 1.3.111.2.802.1.1.10.2.2.5 | | | Objects for the PbbTeConfiguration group. |
| ieee8021PbbTeProtectionConfigOptGroup | 1.3.111.2.802.1.1.10.2.2.6 | | | Objects for the PbbTeConfiguration group. |
| ieee8021PbbTeProtectionGroupISidGroup | 1.3.111.2.802.1.1.10.2.2.7 | | | Objects for the ieee8021PbbTeProtectionGroupISidGroup group. |
| ieee8021PbbTeFdbGroup | 1.3.111.2.802.1.1.10.2.2.8 | | | Fdb extension objects group |
| ieee8021PbbTeNotificationsGroup | 1.3.111.2.802.1.1.10.2.2.9 | | | Objects for the notifications group. |
