HUAWEI-LswRSTP-MIB

All MIBs › HUAWEI-LswRSTP-MIB

Last Updated: 2001-06-29

Category: Protocol: STP, Technology: Switching/L2, Vendor: Huawei

Description: Huawei LAN switch RSTP MIB for managing Rapid Spanning Tree Protocol port roles, states, and topology change events on Huawei switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-LswRSTP-MIB?

HUAWEI-LswRSTP-MIB is a Huawei LAN switch MIB for managing Rapid Spanning Tree Protocol (RSTP) on Huawei switches, exposing per-port role and state information along with topology-change event data. It provides visibility into which ports are root, designated, alternate, or backup, their forwarding/blocking/discarding state, and counts or notifications of topology change events across the switched network. For monitoring, this is primarily a software/protocol health indicator: frequent topology changes or a port unexpectedly transitioning roles can reveal a flapping link, a loop, or a misconfigured redundant path in the Layer 2 topology, while it does not directly expose hardware sensor data. It implements the IEEE 802.1w/802.1D RSTP standard with Huawei-specific extensions layered on top. It is deployed on Huawei LAN switches in enterprise and campus networks that rely on spanning tree for loop prevention and redundant-path failover. Engineers can download the HUAWEI-LswRSTP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-LswRSTP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei enterprise LAN switches (Quidway/S-series, RSTP-capable)

Monitoring Examples

No sample objects were provided, but a realistic scenario would involve polling per-port RSTP role and state objects to confirm the expected root/designated port assignment, and monitoring the topology-change counter for unexpected increments. A rapidly increasing topology-change count would reveal a flapping uplink or a redundant link repeatedly failing over.

What Can Be Monitored

port RSTP role
port forwarding/blocking state
topology change count/events
root bridge information

Imported Objects

From BRIDGE-MIB

dot1dStpPort
dot1dStpPortEntry

From HUAWEI-3COM-OID-MIB

lswCommon

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

MacAddress
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using hwdot1dStpRXStpBPDU OID:

Select a Huawei enterprise LAN switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hwdot1dStpRXStpBPDU into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the number of STP BPDU received. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwLswRstpMib	1.3.6.1.4.1.2011.2.23.1.6
hwLswRstpMibObject	1.3.6.1.4.1.2011.2.23.1.6.1
hwRstpEventsV2	1.3.6.1.4.1.2011.2.23.1.6.1.0			Definition point for RSTP notifications.
NTF hwRstpBpduGuarded	1.3.6.1.4.1.2011.2.23.1.6.1.0.1			The SNMP trap that is generated when an edged port of the BPDU-guard switch recevies BPDU packets.
NTF hwRstpRootGuarded	1.3.6.1.4.1.2011.2.23.1.6.1.0.2			The SNMP trap that is generated when a root-guard port receives a superior bpdu.
NTF hwRstpBridgeLostRootPrimary	1.3.6.1.4.1.2011.2.23.1.6.1.0.3			The SNMP trap that is generated when the bridge is no longer the root bridge of the spanning tree. Another switch with higher priority has already been the root bridge.
NTF hwRstpLoopGuarded	1.3.6.1.4.1.2011.2.23.1.6.1.0.4			The SNMP trap that is generated when a loop-guard port is aged out .
ENA hwdot1dStpStatus	1.3.6.1.4.1.2011.2.23.1.6.1.1	EnabledStatus	read-write	Bridge STP enabled/disabled state
INT hwdot1dStpForceVersion	1.3.6.1.4.1.2011.2.23.1.6.1.2	INTEGER	read-write	Running mode of the bridge RSTP state machine
INT hwdot1dStpDiameter	1.3.6.1.4.1.2011.2.23.1.6.1.3	INTEGER	read-write	Permitted amount of bridges between any two ends on the network.
MAC hwdot1dStpRootBridgeAddress	1.3.6.1.4.1.2011.2.23.1.6.1.4	MacAddress	read-only	MAC address of the root bridge
hwdot1dStpPortXTable	1.3.6.1.4.1.2011.2.23.1.6.1.5		not-accessible	RSTP extended information of the port
hwdot1dStpPortXEntry	1.3.6.1.4.1.2011.2.23.1.6.1.5.1		not-accessible	RSTP extended information of the port
ENA hwdot1dStpPortStatus	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.1	EnabledStatus	read-write	RSTP status of the port
T/F hwdot1dStpPortEdgeport	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.2	TruthValue	read-write	Whether the port can be an edge port
INT hwdot1dStpPortPointToPoint	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.3	INTEGER	read-write	It is the administrative value indicates whether the port can be connected to a point-to-point link or not. If the value is 'auto', the operative value of a point-to-point link state is determined by device itself, and can be read from hwdot1dStpOperPortPointToPoint.
T/F hwdot1dStpMcheck	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.4	TruthValue	read-write	Check if the port transfer state machine enters
INT hwdot1dStpTransLimit	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.5	INTEGER	read-write	Packet transmission limit of the bridge in a duration of Hello Time.
C32 hwdot1dStpRXStpBPDUEx	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.6	Counter32	read-only	Number of STP BPDU received
C32 hwdot1dStpTXStpBPDU	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.7	Counter32	read-only	Number of STP BPDU transmitted
C32 hwdot1dStpRXTCNBPDU	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.8	Counter32	read-only	Number of TCN BPDU received
C32 hwdot1dStpTXTCNBPDU	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.9	Counter32	read-only	Number of TCN BPDU transmitted
C32 hwdot1dStpRXRSTPBPDU	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.10	Counter32	read-only	Number of RSTP BPDU received
C32 hwdot1dStpTXRSTPBPDU	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.11	Counter32	read-only	Number of RSTP BPDU transmitted
INT hwdot1dStpClearStatistics	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.12	INTEGER	read-write	Clear RSTP statistics. Read operation not supported.
INT hwdot1dSetStpDefaultPortCost	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.13	INTEGER	read-write	Set PathCost back to the default setting. Read operation not supported.
ENA hwdot1dStpRootGuard	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.14	EnabledStatus	read-write	If the port guard root bridge. Other bridge which want to be root can not become root through this port if enabled.
ENA hwdot1dStpLoopGuard	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.15	EnabledStatus	read-write	Loop guard function that keep a root port or an alternate port in discarding state while the information on the port is aged out.
INT hwdot1dStpPortBlockedReason	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.16	INTEGER	read-only	Record the block reason of the port. notBlock (1) means that the port is not in block state,. blockForProtocol (2) means that the port is blocked by stp protocol to avoid loop. blockForRootGuard(3) means that the root guard flag of bridge is set and a better message received from the port,and the port is blocked. blockForBPDUGuard(4) means that the port has been configured as an edge port and receive a BPDU and thus blocked. blockForLoopGuard(5) means that the port is blocked for loopguarded.
C32 hwdot1dStpRXTCBPDU	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.17	Counter32	read-only	The number of received TC BPDUs
INT hwdot1dStpPortSendingBPDUType	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.18	INTEGER	read-only	Type of BPDU which the port is sending.
INT hwdot1dStpOperPortPointToPoint	1.3.6.1.4.1.2011.2.23.1.6.1.5.1.19	INTEGER	read-only	This object indicates whether the port has connected to a point-to-point link or not. The administrative value should be read from hwdot1dStpPortPointToPoint.
ENA hwDot1dStpBpduGuard	1.3.6.1.4.1.2011.2.23.1.6.1.6	EnabledStatus	read-write	If BPDU guard enabled. The edge port will discard illegal BPDU when enabled
INT hwDot1dStpRootType	1.3.6.1.4.1.2011.2.23.1.6.1.7	INTEGER	read-write	Root type of the bridge
INT hwDot1dTimeOutFactor	1.3.6.1.4.1.2011.2.23.1.6.1.8	INTEGER	read-write	Time Out Factor of the bridge.
INT hwDot1dStpPathCostStandard	1.3.6.1.4.1.2011.2.23.1.6.1.9	INTEGER	read-write	Path Cost Standard of the bridge. Value 'dot1d-1998' is IEEE 802.1d standard in 1998, value 'dot1t' is IEEE 802.1t standard, and value 'legacy' is a private legacy standard.
hwdot1dStpIgnoredVlanTable	1.3.6.1.4.1.2011.2.23.1.6.1.10		not-accessible	RSTP extended information of vlan
hwdot1dStpIgnoredVlanEntry	1.3.6.1.4.1.2011.2.23.1.6.1.10.1		not-accessible	RSTP extended information of the vlan
INT hwdot1dVlan	1.3.6.1.4.1.2011.2.23.1.6.1.10.1.1	INTEGER	read-only	Vlan id supported
INT hwdot1dStpIgnore	1.3.6.1.4.1.2011.2.23.1.6.1.10.1.2	INTEGER	read-write	Whether the vlan is stp Ignored

RFC description

Huawei Rapid Spanning Tree Protocol (RSTP) MIB for bridge loop prevention on LAN switches.

Start monitoring Huawei enterprise LAN switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-LswRSTP-MIB